Since 2010, the global 3D printing market has been in a period of rapid development, with an AAGR of 30% or so. In 2014, the market size totaled USD4.1 billion. 3D printing mainly involves software, equipment, materials and service, of which 3D printing equipment accounted for about 46.5% in the industry in 2014.
Additive Manufacturing (AM) Adding up Growth Opportunities for ASEANAbhinav Singhal
Additive Manufacturing (AM), also known as 3D printing, is currently at a technological and economical inflection point with potential to re-invent and disrupt the ~$12 trillion global manufacturing sector. Manufacturing is also at the center of the ASEAN economy driven by its cost competitiveness accounting for more than 20% of the region’s GDP and employing nearly 50 million workforce.
However, AM has potential to disrupt traditional manufacturing cost structures and supply chains and give an equal opportunity to advanced economies to close their competitiveness gap and move manufacturing nearer to the end consumers. This poses a risk for ASEAN to fall behind and ASEAN needs to act now to secure its place in the age of Fourth Industrial revolution.
However, very little empirical research exists on the current status of AM in ASEAN (i.e., status of current adoption, leading markets & sectors, opportunities) leaving policymakers and business leaders without any guidance to best prepare for the future.
thyssenkrupp recognized this gap and assembled a multidisciplinary team of experts to construct a comprehensive perspective on the state of AM in the region and its implications for policymakers and businesses going forward. This builds on our rich working experience in the region over the last 150 years, our deep AM technology expertise in Mulheim, our recent set-up in Singapore, and the knowledge of our experts and our partners from EOS and NAMIC across the whole AM value chain.
This whitepaper provides a rich evidence base for policymakers and business leaders seeking to understand, analyze and invest in AM in ASEAN. The paper is structured along three chapters keeping in mind the diverse interest of various stakeholders:
• For business leaders: Chapter 1 provides a detailed overview of the AM market and its potential across ASEAN countries; while Chapter 3 lays down a systematic approach to analyze AM value chain and develop a commercially attractive business model
• For policy makers: Chapter 2 outlines the overall economic opportunity from adopting AM in ASEAN and the impact it can create across various aspects of the economy from trade, social development, job creation to sustainability
• For AM enthusiasts: Appendix 1 provides a brief overview of the technology and its applications today
We invite you to study the findings of this whitepaper and we look forward to partnering with you in driving your AM priorities for the region.
Asia Pacific Industrial 3D Printing Market Analysis, 2020ShivaKumar1833
The Asia-Pacific industrial 3D printing market is driven primarily by government initiatives. The government of China and Singapore have committed millions of dollars to develop and commercialize 3D printing. Japan’s New Energy and Industrial Technology Development Organization (NEDO), invested in a 3D printing technology that can fabricate from pure copper by using a high-intensity blue laser diode. As the project made from 3D printers are designed on a software program, design creation and redesign challenges can be easily overcome by updating the file on the program. This reduces, and in some cases, eliminates the trial and error process and the high costs associated with re-tooling, redesign, and rework as with the traditional manufacturing method, thus reducing the overall product development cycle time. Therefore, the demand for industrial 3D printing is generating in the region.
Automotive 3 d printing market global trends, market share, industry size, gr...Shubham Bhosale
Automotive engineering prototypes involve complex mechanical geometric blueprints widely used in the manufacturing process of various automotive parts. Advanced 3D printing technology utilizes precision based high-resolution design tools reducing the human errors, cost, time and customization efforts as compared to traditional ways. Layer by layer depositing of raw material using 3D printing facilitates substantial material wastage reduction.
Automotive 3 d printing market global trends, market share, industry size, gr...itejasmore
Automotive 3 d printing market global trends, market share, industry size, growth, opportunities, and market forecast. Market Research Reports and Analysis - FutureWise Market Research - UK
Additive Manufacturing (AM) Adding up Growth Opportunities for ASEANAbhinav Singhal
Additive Manufacturing (AM), also known as 3D printing, is currently at a technological and economical inflection point with potential to re-invent and disrupt the ~$12 trillion global manufacturing sector. Manufacturing is also at the center of the ASEAN economy driven by its cost competitiveness accounting for more than 20% of the region’s GDP and employing nearly 50 million workforce.
However, AM has potential to disrupt traditional manufacturing cost structures and supply chains and give an equal opportunity to advanced economies to close their competitiveness gap and move manufacturing nearer to the end consumers. This poses a risk for ASEAN to fall behind and ASEAN needs to act now to secure its place in the age of Fourth Industrial revolution.
However, very little empirical research exists on the current status of AM in ASEAN (i.e., status of current adoption, leading markets & sectors, opportunities) leaving policymakers and business leaders without any guidance to best prepare for the future.
thyssenkrupp recognized this gap and assembled a multidisciplinary team of experts to construct a comprehensive perspective on the state of AM in the region and its implications for policymakers and businesses going forward. This builds on our rich working experience in the region over the last 150 years, our deep AM technology expertise in Mulheim, our recent set-up in Singapore, and the knowledge of our experts and our partners from EOS and NAMIC across the whole AM value chain.
This whitepaper provides a rich evidence base for policymakers and business leaders seeking to understand, analyze and invest in AM in ASEAN. The paper is structured along three chapters keeping in mind the diverse interest of various stakeholders:
• For business leaders: Chapter 1 provides a detailed overview of the AM market and its potential across ASEAN countries; while Chapter 3 lays down a systematic approach to analyze AM value chain and develop a commercially attractive business model
• For policy makers: Chapter 2 outlines the overall economic opportunity from adopting AM in ASEAN and the impact it can create across various aspects of the economy from trade, social development, job creation to sustainability
• For AM enthusiasts: Appendix 1 provides a brief overview of the technology and its applications today
We invite you to study the findings of this whitepaper and we look forward to partnering with you in driving your AM priorities for the region.
Asia Pacific Industrial 3D Printing Market Analysis, 2020ShivaKumar1833
The Asia-Pacific industrial 3D printing market is driven primarily by government initiatives. The government of China and Singapore have committed millions of dollars to develop and commercialize 3D printing. Japan’s New Energy and Industrial Technology Development Organization (NEDO), invested in a 3D printing technology that can fabricate from pure copper by using a high-intensity blue laser diode. As the project made from 3D printers are designed on a software program, design creation and redesign challenges can be easily overcome by updating the file on the program. This reduces, and in some cases, eliminates the trial and error process and the high costs associated with re-tooling, redesign, and rework as with the traditional manufacturing method, thus reducing the overall product development cycle time. Therefore, the demand for industrial 3D printing is generating in the region.
Automotive 3 d printing market global trends, market share, industry size, gr...Shubham Bhosale
Automotive engineering prototypes involve complex mechanical geometric blueprints widely used in the manufacturing process of various automotive parts. Advanced 3D printing technology utilizes precision based high-resolution design tools reducing the human errors, cost, time and customization efforts as compared to traditional ways. Layer by layer depositing of raw material using 3D printing facilitates substantial material wastage reduction.
Automotive 3 d printing market global trends, market share, industry size, gr...itejasmore
Automotive 3 d printing market global trends, market share, industry size, growth, opportunities, and market forecast. Market Research Reports and Analysis - FutureWise Market Research - UK
With some experts predicting that 3D printing will have more impact on economies and society than the internet, manufacturing industries are expected to look for opportunities for the early adoption of this game changing, innovative, technology. However, a recent report by Ipsos Business Consulting and VNU Exhibitions Asia suggests that manufacturers in China are adopting 3D printing technology at a much slower pace than anticipated.
Contact our China team to find out more. Email: china.bc@ipsos.com
China printing and dyeing auxiliary industry report, 2014 2017ResearchInChina
Printing and dyeing auxiliaries are crucial for the upgrading and generation replacement of textile products and the growth of added value. In 2006-2012, China’s printing and dyeing auxiliary output showed an uptrend with a CAGR of 8.8%. In 2013, the output reached 1.366 million tons, representing a slight increase over 2012.
Market Reports on India presents the latest report on “India 3d Printing Market”. http://www.marketreportsonindia.com/technology-media-market-research-reports-13772/india-3d-printing-material-plastics-photopolymers.html The technology allows printing with suitable range of materials in lesser time.
With Korea acting as a fast follower rather than an innovator in the 3D printing industry, Korean companies are now setting their sights on catching up to the field in this quickly developing sector. In this Ipsos publication, we review the Korean 3D printing industry in its present state, including its most promising opportunities as well as the barriers to success that business is currently facing. We then put a special focus on the major Korean players, the parts of industry where the technology is most likely to take hold in the coming years, and how the government and businesses are stepping up to the challenge. The Ipsos publication includes:
- Market Potential of the Korean 3D Printing Industry
- Barriers to Growth in the Korean 3D Printing Industry
- Detailed Trends of the Korean 3D Printing Industry, by Sector
- 3D Printing in the Education and Health Sectors within Korea
- Korean Government Policies for 3D Printing
- Government Investment in Korean 3D Printing Industry
- Future Prospects for the Korean 3D Printing Industry
Email your questions and comments about this Ipsos paper on the developments in Korean 3D Printing paper to korea.bc@ipsos.com
Blog – What is next for 3D printing – April 2021.
1. How 3D printing is changing the world - https://www.creativebloq.com/features/12-ways-3d-printing-changed-the-world
2. Canada trails other countries with the adoption of 3D printing - https://www.3dnatives.com/en/results-from-3d-printing-sentiment-index-show-global-growth-despite-pandemic/
3. Five myths about 3D printing - https://www.rcgt.com/en/insights/five-myths-about-3d-printing/
4. Canada has issues with productivity - https://tradingeconomics.com/canada/productivity or https://www.imd.org/news/updates/IMD-2020-World-Competitiveness-Ranking-revealed/
5. Canada is falling behind on its competitiveness https://www.businesscouncilab.com/work/canada-is-falling-behind-and-has-no-plan-to-get-ahead/
6. 3D printing of houses - https://www.3dsourced.com/guides/3d-printed-house-2/
7. EMEA a global hub for 3D printing - https://www.epo.org/news-events/news/2020/20200713.html
8. Canada needs to do more to promote innovation through grants and tax policies open to everyone - https://www.visualcapitalist.com/national-innovation-the-most-innovative-countries-by-income/. The goal of any govt is not to pick winners and losers.
9. Canada trails many countries in terms of automation - https://ifr.org/ifr-press-releases/news/robot-race-the-worlds-top-10-automated-countries
10. How 3D printing can help the environment - https://all3dp.com/4/7-ways-3d-printing-helps-you-become-eco-friendly/
The global 3d printing software market generated revenue of US$ XX.X million in 2020 and is expected to reach US$ XX.X million by 2025 with a CAGR of XX.X% in the forecast period. The 3d printing software market report offers a comprehensive market analysis of the different segments and regions that lets readers make crucial business-related decisions with a wealth of information enclosed in this report. The research report offers both qualitative and quantitative information on the global 3d printing software market. In qualitative terms, the 3d printing software market report provides insights into numerous factors, such as market determinants, value chain analysis, emerging trends, growth opportunity analysis, Porter five-force model analysis, macro-economic factors, segment analysis, and regional analysis at a granular level. Similarly, in quantitative terms, the report provides historical and forecast market numbers of 3d printing software in various segments such as by component, deployment model, technology, enterprise size & end-user at global, regional, and country-level. Also, the report provides a detailed analysis of the market vendors and their product offerings. The report also covers details of the competitive market environment and includes information on the capabilities and competencies of market vendors.
Rapid Prototyping or Additive Manufacturing Industry AnalysisRajesh Maji
The scope of business opportunities brought by Additive Manufacturing is tremendous, but still the industry is in research and development phase. The companies who are active in product and process standardization will gain competitive advantage in future.
Global and china vr and ar industry research summary, 2016 2020 [兼容模式]ResearchInChina
VR Trends:
Gradually-formed industrial standards raise access threshold, thus eliminating less competitive teams and companies;
Large companies gradually build perfect VR ecosystem;
PC VR products, primarily games and movies, will be targeted at expert players and game enthusiasts;
Mobile VR products gradually move into business fields like education and tourism;
The number of content development teams will increase, and the scope of VR contents will broaden.
3-D printing or additive manufacturing is the process which builds layer upon layer to create a three dimensional solid object from a digital model with the help of computer system. The computer controls layer by layer material deposition maintains very low wastage of printing material.
The aims of the presentation are to:
- Present what leading analysts say on trends in 2015
- Outline what new skills will be required in 2015+
- Suggest some market niches for growth
with focus on IT market.
Global and china animation industry report, 2014ResearchInChina
From the production and broadcast market, China’s animation production suffered three consecutive years of decline (2011-2013). In 2013 China produced 358 domestic TV cartoons, a total of 204,732 minutes long, respectively down 9.37% and 8.17% year on year, mainly because it was difficult for government subsidiaries to cover the increasingly higher costs of production. In addition, the original IP resource scarcity has been a tough and unbreakable bottleneck for domestic animation.
Global and china li ion power battery industry report , 2017-2020ResearchInChina
There are three major technology roadmaps for power battery around the world:
(1) Ternary materials-based: NCA and NCM as main cathode materials. Featuring high energy density, NCM batteries have become a mainstream battery technology for electric vehicles along with a sharp cutin procurement costs of the batteries in recent years. Chinese battery enterprises, represented by Tianjin Lishen and Boston Power, have started the production of NCM batteries since 2014. NCA is chiefly used in 18650-type battery (the highest energy density so far), which supports mainly Tesla and Toyota RAV4. However, due to strong chemical activity of aluminum mixed in NCA, advanced BMS is needed to monitor the operating condition of the battery, thus resulting in a low penetration in carmakers.
(2) LFP-based. Canada and the United States were the first countries to develop power battery technology. In China, LFP, the mainstream technology for power lithium battery, is widely used in passenger cars and buses, with the typical enterprises including BYD and Guoxuan High-tech. However, due to the factors like low specific energy and poor low-temperature starting performance, LFP batteries still have not been widely used worldwide.
(3) Manganese series: with LMO as main cathode material. LMO is generally modified and is mixed with a small amount of NCM or LNO to raise battery energy density. Key representative manufacturers are LGC, AESC, LEJ, etc. And in China, they are CITIC Guoan MGL, Do-Fluoride Chemicals, etc.
China silicon carbide industry report, 2016 2020ResearchInChina
Since China's silicon carbide export quota was abolished, China’s silicon carbide export volume grew rapidly during 2013-2014, and tended to stabilize during 2015-2016. In 2016, China’s silicon carbide exports came to 321,500 tons, up 2.1% year on year; wherein, Ningxia’s export volume amounted to 111,900 tons, accounting for 34.9% of the total exports and acting as a main silicon carbide exporter in China.
As China's silicon carbide products are mainly low-end preliminarily processed products with moderate added value, the average price gap between export and import is enormous. In 2016, China's silicon carbide exports had the average price at USD0.9 / kg, less than 1/4 of the import average price (USD4.3 / kg).
More Related Content
Similar to Global and china 3 d printing industry report, 2015 2018
With some experts predicting that 3D printing will have more impact on economies and society than the internet, manufacturing industries are expected to look for opportunities for the early adoption of this game changing, innovative, technology. However, a recent report by Ipsos Business Consulting and VNU Exhibitions Asia suggests that manufacturers in China are adopting 3D printing technology at a much slower pace than anticipated.
Contact our China team to find out more. Email: china.bc@ipsos.com
China printing and dyeing auxiliary industry report, 2014 2017ResearchInChina
Printing and dyeing auxiliaries are crucial for the upgrading and generation replacement of textile products and the growth of added value. In 2006-2012, China’s printing and dyeing auxiliary output showed an uptrend with a CAGR of 8.8%. In 2013, the output reached 1.366 million tons, representing a slight increase over 2012.
Market Reports on India presents the latest report on “India 3d Printing Market”. http://www.marketreportsonindia.com/technology-media-market-research-reports-13772/india-3d-printing-material-plastics-photopolymers.html The technology allows printing with suitable range of materials in lesser time.
With Korea acting as a fast follower rather than an innovator in the 3D printing industry, Korean companies are now setting their sights on catching up to the field in this quickly developing sector. In this Ipsos publication, we review the Korean 3D printing industry in its present state, including its most promising opportunities as well as the barriers to success that business is currently facing. We then put a special focus on the major Korean players, the parts of industry where the technology is most likely to take hold in the coming years, and how the government and businesses are stepping up to the challenge. The Ipsos publication includes:
- Market Potential of the Korean 3D Printing Industry
- Barriers to Growth in the Korean 3D Printing Industry
- Detailed Trends of the Korean 3D Printing Industry, by Sector
- 3D Printing in the Education and Health Sectors within Korea
- Korean Government Policies for 3D Printing
- Government Investment in Korean 3D Printing Industry
- Future Prospects for the Korean 3D Printing Industry
Email your questions and comments about this Ipsos paper on the developments in Korean 3D Printing paper to korea.bc@ipsos.com
Blog – What is next for 3D printing – April 2021.
1. How 3D printing is changing the world - https://www.creativebloq.com/features/12-ways-3d-printing-changed-the-world
2. Canada trails other countries with the adoption of 3D printing - https://www.3dnatives.com/en/results-from-3d-printing-sentiment-index-show-global-growth-despite-pandemic/
3. Five myths about 3D printing - https://www.rcgt.com/en/insights/five-myths-about-3d-printing/
4. Canada has issues with productivity - https://tradingeconomics.com/canada/productivity or https://www.imd.org/news/updates/IMD-2020-World-Competitiveness-Ranking-revealed/
5. Canada is falling behind on its competitiveness https://www.businesscouncilab.com/work/canada-is-falling-behind-and-has-no-plan-to-get-ahead/
6. 3D printing of houses - https://www.3dsourced.com/guides/3d-printed-house-2/
7. EMEA a global hub for 3D printing - https://www.epo.org/news-events/news/2020/20200713.html
8. Canada needs to do more to promote innovation through grants and tax policies open to everyone - https://www.visualcapitalist.com/national-innovation-the-most-innovative-countries-by-income/. The goal of any govt is not to pick winners and losers.
9. Canada trails many countries in terms of automation - https://ifr.org/ifr-press-releases/news/robot-race-the-worlds-top-10-automated-countries
10. How 3D printing can help the environment - https://all3dp.com/4/7-ways-3d-printing-helps-you-become-eco-friendly/
The global 3d printing software market generated revenue of US$ XX.X million in 2020 and is expected to reach US$ XX.X million by 2025 with a CAGR of XX.X% in the forecast period. The 3d printing software market report offers a comprehensive market analysis of the different segments and regions that lets readers make crucial business-related decisions with a wealth of information enclosed in this report. The research report offers both qualitative and quantitative information on the global 3d printing software market. In qualitative terms, the 3d printing software market report provides insights into numerous factors, such as market determinants, value chain analysis, emerging trends, growth opportunity analysis, Porter five-force model analysis, macro-economic factors, segment analysis, and regional analysis at a granular level. Similarly, in quantitative terms, the report provides historical and forecast market numbers of 3d printing software in various segments such as by component, deployment model, technology, enterprise size & end-user at global, regional, and country-level. Also, the report provides a detailed analysis of the market vendors and their product offerings. The report also covers details of the competitive market environment and includes information on the capabilities and competencies of market vendors.
Rapid Prototyping or Additive Manufacturing Industry AnalysisRajesh Maji
The scope of business opportunities brought by Additive Manufacturing is tremendous, but still the industry is in research and development phase. The companies who are active in product and process standardization will gain competitive advantage in future.
Global and china vr and ar industry research summary, 2016 2020 [兼容模式]ResearchInChina
VR Trends:
Gradually-formed industrial standards raise access threshold, thus eliminating less competitive teams and companies;
Large companies gradually build perfect VR ecosystem;
PC VR products, primarily games and movies, will be targeted at expert players and game enthusiasts;
Mobile VR products gradually move into business fields like education and tourism;
The number of content development teams will increase, and the scope of VR contents will broaden.
3-D printing or additive manufacturing is the process which builds layer upon layer to create a three dimensional solid object from a digital model with the help of computer system. The computer controls layer by layer material deposition maintains very low wastage of printing material.
The aims of the presentation are to:
- Present what leading analysts say on trends in 2015
- Outline what new skills will be required in 2015+
- Suggest some market niches for growth
with focus on IT market.
Global and china animation industry report, 2014ResearchInChina
From the production and broadcast market, China’s animation production suffered three consecutive years of decline (2011-2013). In 2013 China produced 358 domestic TV cartoons, a total of 204,732 minutes long, respectively down 9.37% and 8.17% year on year, mainly because it was difficult for government subsidiaries to cover the increasingly higher costs of production. In addition, the original IP resource scarcity has been a tough and unbreakable bottleneck for domestic animation.
Similar to Global and china 3 d printing industry report, 2015 2018 (20)
Global and china li ion power battery industry report , 2017-2020ResearchInChina
There are three major technology roadmaps for power battery around the world:
(1) Ternary materials-based: NCA and NCM as main cathode materials. Featuring high energy density, NCM batteries have become a mainstream battery technology for electric vehicles along with a sharp cutin procurement costs of the batteries in recent years. Chinese battery enterprises, represented by Tianjin Lishen and Boston Power, have started the production of NCM batteries since 2014. NCA is chiefly used in 18650-type battery (the highest energy density so far), which supports mainly Tesla and Toyota RAV4. However, due to strong chemical activity of aluminum mixed in NCA, advanced BMS is needed to monitor the operating condition of the battery, thus resulting in a low penetration in carmakers.
(2) LFP-based. Canada and the United States were the first countries to develop power battery technology. In China, LFP, the mainstream technology for power lithium battery, is widely used in passenger cars and buses, with the typical enterprises including BYD and Guoxuan High-tech. However, due to the factors like low specific energy and poor low-temperature starting performance, LFP batteries still have not been widely used worldwide.
(3) Manganese series: with LMO as main cathode material. LMO is generally modified and is mixed with a small amount of NCM or LNO to raise battery energy density. Key representative manufacturers are LGC, AESC, LEJ, etc. And in China, they are CITIC Guoan MGL, Do-Fluoride Chemicals, etc.
China silicon carbide industry report, 2016 2020ResearchInChina
Since China's silicon carbide export quota was abolished, China’s silicon carbide export volume grew rapidly during 2013-2014, and tended to stabilize during 2015-2016. In 2016, China’s silicon carbide exports came to 321,500 tons, up 2.1% year on year; wherein, Ningxia’s export volume amounted to 111,900 tons, accounting for 34.9% of the total exports and acting as a main silicon carbide exporter in China.
As China's silicon carbide products are mainly low-end preliminarily processed products with moderate added value, the average price gap between export and import is enormous. In 2016, China's silicon carbide exports had the average price at USD0.9 / kg, less than 1/4 of the import average price (USD4.3 / kg).
Global and china hd map industry research summary, 2016 [兼容模式]ResearchInChina
Overall, autonomous driving is now dominated by automakers, and they will not completely open their underlying data on vehicles to HD map providers. Thus, many auto makers (like Audi, Mercedes-Benz, and BMW), obtain HD map data sources by acquiring digital map providers. In contrast, due to a lack of experience in fault tolerance and underlying data of vehicles, Internet companies end up cooperating with automakers.
Global and china natural rubber industry report, 2016 2020ResearchInChina
Due to the sluggish global economic growth and the excess supply of natural rubber, the price of natural rubber has been hovering at a low level. As of the end of 2015, China's natural rubber price had fallen to around USD1,140 / ton which was also the cost price. In 2016, the global average price of natural rubber fluctuates at USD1,200-1,500 / ton.
Automotive PCB market is the biggest highlight. Global automotive PCB market size was USD5.28 billion in 2015 and is expected to grow by 8.3% to USD5.72 billion in 2016 and by 8.2% to USD6.19 billion in 2017, primarily because of impetus of millimeter-wave radar to RF board, of connected vehicle to multi-layer board, and of chassis electronization to metal substrate.
Global and china titanium dioxide industry report, 2016 2020ResearchInChina
In 2015, the global titanium dioxide market size hit EUR10.17 billion, up 3.7% year on year. In 2016-2020, the global market size is expected to present a CAGR of around 4.5% and reach nearly EUR13 billion in 2020.
As consumers have growing awareness of car navigation products as well as telematics develops radically, the global car navigation market witnesses steady development and a higher penetration rate. In 2015, the global embedded automotive navigation system shipment was estimated at 23.9 million sets, with the market size of USD21.6 billion; in 2016, the shipment will reach 25.3 million sets, with the market size up to USD22.6 billion.
From January to May of 2016, China preinstalled 2.074 million sets of car navigation; in 2016, the figure will exceed 5 million sets and hit 5.563 million sets.
Currently, Chinese car navigation map OEMs include NavInfo, AutoNavi (AMAP) and eMapgo Technologies (Beijing); aftermarket map companies embrace Careland, Ritu and NavInfo, among which, NavInfo and Careland occupy the majority of market share in the OEM market and the aftermarket respectively.
In the next few years, China’s preinstalled car navigation will jump year by year, with the expected amount of 9.55 million sets by 2020 and the CAGR of 15% in 2016-2020.
The increase of preinstallation is driven by the two below:
1. The navigation installation ratio of vehicle models for sale increases steadily
As of May 2016, 4,724 models of passenger cars had been on sale in the Chinese market, including 1,782 models equipped with navigation systems, with the installation ratio of 37.7%; among them, Haval’s 130 models had been equipped with navigation systems with the installation ratio of 85%, ranking first. Independent brands, such as Haval, Chang'an, Geely and BYD, played main roles in promoting navigation systems.
2. Automotive navigation has spread gradually from medium and high-end vehicle models to low-end models.
In terms of the navigation installation ratio of vehicle models on sale, 1,245 models tagged with the unit price of RMB200,000 or less were equipped with navigation in May 2016, compared with 1,004 models in? January; correspondingly, the navigation installation ratio ascended from 31.1% to 32.7%. This shows that Chinese car navigation has spread gradually from medium and high-end vehicle models to low-end models.
Global and china supercapacitor industry report, 2016 2020ResearchInChina
Globally, supercapacitor is primarily applied to consumer electronics and transportation, which made up 47% and 29% of total supercapacitor consumption respectively in 2015. The demand for supercapacitor from transportation, particularly electric vehicles, has risen rapidly and is expected to account for roughly 41% in 2020, becoming the largest application field of supercapacitor.
Global and china carbon fiber and cfrp industry report, 2016 2020ResearchInChina
The global carbon fiber demand amounted to 59,000 tons in 2015. 22%, 62% and 16% of carbon fiber were applied to aerospace, industries, and sports & leisure respectively. Specifically, the demand from industries grew fastest, especially from automobiles, wind power, pressure vessels and other market segments. By 2020, 72% of the global carbon fiber will be used in industries, of which 23% will be adopted by automobiles and 21% by wind power.
China etc (electronic toll collection) industry report, 2015 2019ResearchInChina
The Chinese ETC equipment (OBU, RSU) market size has expanded rapidly in recent years, growing at a CAGR of 33.5% during 2012-2014. With advances in networked ETC nationwide, the Chinese ETC equipment market size is estimated to be up to RMB1.35 billion in 2015, presenting a year-on-year jump of 40.5%.
Global and china low e glass industry report, 2015-2018ResearchInChina
Although China’s Low-E glass capacity grows rapidly, the constraint of production technologies (especially online coating technology) leads to a low capacity utilization rate. In 2014, China’s Low-E glass output ascended 11.9% year on year to 150 million m2, while the capacity utilization rate was only 25.1%. In 2015, the capacity utilization rate is expected to hit 25.8% amid the stable glass market. In addition, China's Low-E glass penetration rate is less than 15%, still lagging far behind 80% in Europe, Japan, South Korea, the United States and other developed countries.
Global and china li ion power battery industry report, 2016-2020ResearchInChina
In 2014, the global demand for Li-ion power battery for electric vehicles came to 9.8GWh, up 87% from a year earlier, of which the demand from passenger vehicles totaled 7.3GWh and commercial vehicles 2.5GWh. In H1 2015, the global demand for EV Li-ion power battery hit 7GWh, maintaining high growth
Global and china graphene industry report, 2015 2018ResearchInChina
Global graphene market size is only USD24.4 million in 2015, and most of demand comes from semiconductor electronics, lithium battery and composite materials industries, which seize a combined 60.1% share. As progress is made in the industrialized application of graphene, global graphene market size is expected to hit USD65 million in 2018.
China tire curing press industry report,2015 2018 ResearchInChina
By the end of 2014, there are about 40 tire curing press manufacturers in China with the annual capacity of 4,500 units or so, mainly distributed in major tire-producing provinces such as Shandong province (Qingdao city), Jiangsu province, Guangdong province. Among them, only Guilin Rubber Machinery and Sino-Rubber Machinery have annual capacity of more than 500 units of curing press, others produce 200-400 units a year. In 2014, Guilin Rubber Machinery, Yiyang Rubber & Plastics Machinery Group, Greatoo Inc., Sino-Rubber Machinery, Guangzhou SCUT Bestry Technology occupied the top five spots of curing press production ranking.
Global and china tyre pressure monitoring system (tpms) industry report, 2015...ResearchInChina
South Korea, European Union, and Taiwan joined the camp that forces the installation of TPMS in 2014, as the former in Jul 2014 and the latter two in Nov 2014 asked that related auto models must be installed with TPMS, directly boosting global demand for the product. Global installation rate of TPMS reached 36% in 2014, up 6 percentage points from 2013, and is expected to exceed 45% in 2015, creating a demand of more than 40 million sets.
The development of automobiles, machinery manufacturing, electrical, and other industries in China has triggered a rapid expansion of lubricant market size. So far, China has become one of the world’s major lubricant producers and consumers. However, amid the low-speed growth of the global economy, China’s lubricant market continued to decline for the past two years, with 2014’s lubricant output falling by 3.6% year-on-year to 5.6866 million tons.
China financial leasing industry report, 2015ResearchInChina
Although China’s economic growth posted continuous downturn, China financial leasing industry maintained fast increase since 2014, with total turnover reaching around RMB 3,420 billion as of the end of March 2015, up about RMB 220 billion compared to the end of 2014. The number of enterprises totaled 2,661, an increase of 459 compared to the end of 2014. The number of foreign leasing enterprises enjoyed the fastest growth, being 2,440, an increase of 420.
Global and china automotive seating industry report, 2014 2015ResearchInChina
The seemingly simple automotive seating actually reflects a country's machining ability. In the world, at most 20 companies are capable of producing automotive seating whose frames are made of precision metals via stamping, while nearly a thousand companies have the capability to produce automotive engines.
Global and china ic substrate industry report, 2015ResearchInChina
IC substrate industry may be in a predicament in 2015, rooted in two aspects: first, the maturing of FOWLP; second, the tablet sales decline and sluggish smartphone growth. In addition, the prosperity of IC substrate industry in 2013 stimulated large-scale expansion of enterprises in 2014, thus leading to an insufficient rate of capacity utilization.
Global and china rigid pcb industry report, 2015ResearchInChina
2014 was a good year for majority of PCB companies, as output value of PCB industry touched USD59.6 billion, rising 3.7% against 2013, the fastest growth rate since 2011. Looking forward to 2015, a collapse in prices of commodities, especially in that of copper, will significantly reduce raw materials costs of PCB companies, thus further driving their profit margins.
UiPath Test Automation using UiPath Test Suite series, part 3DianaGray10
Welcome to UiPath Test Automation using UiPath Test Suite series part 3. In this session, we will cover desktop automation along with UI automation.
Topics covered:
UI automation Introduction,
UI automation Sample
Desktop automation flow
Pradeep Chinnala, Senior Consultant Automation Developer @WonderBotz and UiPath MVP
Deepak Rai, Automation Practice Lead, Boundaryless Group and UiPath MVP
Generating a custom Ruby SDK for your web service or Rails API using Smithyg2nightmarescribd
Have you ever wanted a Ruby client API to communicate with your web service? Smithy is a protocol-agnostic language for defining services and SDKs. Smithy Ruby is an implementation of Smithy that generates a Ruby SDK using a Smithy model. In this talk, we will explore Smithy and Smithy Ruby to learn how to generate custom feature-rich SDKs that can communicate with any web service, such as a Rails JSON API.
UiPath Test Automation using UiPath Test Suite series, part 4DianaGray10
Welcome to UiPath Test Automation using UiPath Test Suite series part 4. In this session, we will cover Test Manager overview along with SAP heatmap.
The UiPath Test Manager overview with SAP heatmap webinar offers a concise yet comprehensive exploration of the role of a Test Manager within SAP environments, coupled with the utilization of heatmaps for effective testing strategies.
Participants will gain insights into the responsibilities, challenges, and best practices associated with test management in SAP projects. Additionally, the webinar delves into the significance of heatmaps as a visual aid for identifying testing priorities, areas of risk, and resource allocation within SAP landscapes. Through this session, attendees can expect to enhance their understanding of test management principles while learning practical approaches to optimize testing processes in SAP environments using heatmap visualization techniques
What will you get from this session?
1. Insights into SAP testing best practices
2. Heatmap utilization for testing
3. Optimization of testing processes
4. Demo
Topics covered:
Execution from the test manager
Orchestrator execution result
Defect reporting
SAP heatmap example with demo
Speaker:
Deepak Rai, Automation Practice Lead, Boundaryless Group and UiPath MVP
Elevating Tactical DDD Patterns Through Object CalisthenicsDorra BARTAGUIZ
After immersing yourself in the blue book and its red counterpart, attending DDD-focused conferences, and applying tactical patterns, you're left with a crucial question: How do I ensure my design is effective? Tactical patterns within Domain-Driven Design (DDD) serve as guiding principles for creating clear and manageable domain models. However, achieving success with these patterns requires additional guidance. Interestingly, we've observed that a set of constraints initially designed for training purposes remarkably aligns with effective pattern implementation, offering a more ‘mechanical’ approach. Let's explore together how Object Calisthenics can elevate the design of your tactical DDD patterns, offering concrete help for those venturing into DDD for the first time!
State of ICS and IoT Cyber Threat Landscape Report 2024 previewPrayukth K V
The IoT and OT threat landscape report has been prepared by the Threat Research Team at Sectrio using data from Sectrio, cyber threat intelligence farming facilities spread across over 85 cities around the world. In addition, Sectrio also runs AI-based advanced threat and payload engagement facilities that serve as sinks to attract and engage sophisticated threat actors, and newer malware including new variants and latent threats that are at an earlier stage of development.
The latest edition of the OT/ICS and IoT security Threat Landscape Report 2024 also covers:
State of global ICS asset and network exposure
Sectoral targets and attacks as well as the cost of ransom
Global APT activity, AI usage, actor and tactic profiles, and implications
Rise in volumes of AI-powered cyberattacks
Major cyber events in 2024
Malware and malicious payload trends
Cyberattack types and targets
Vulnerability exploit attempts on CVEs
Attacks on counties – USA
Expansion of bot farms – how, where, and why
In-depth analysis of the cyber threat landscape across North America, South America, Europe, APAC, and the Middle East
Why are attacks on smart factories rising?
Cyber risk predictions
Axis of attacks – Europe
Systemic attacks in the Middle East
Download the full report from here:
https://sectrio.com/resources/ot-threat-landscape-reports/sectrio-releases-ot-ics-and-iot-security-threat-landscape-report-2024/
DevOps and Testing slides at DASA ConnectKari Kakkonen
My and Rik Marselis slides at 30.5.2024 DASA Connect conference. We discuss about what is testing, then what is agile testing and finally what is Testing in DevOps. Finally we had lovely workshop with the participants trying to find out different ways to think about quality and testing in different parts of the DevOps infinity loop.
Kubernetes & AI - Beauty and the Beast !?! @KCD Istanbul 2024Tobias Schneck
As AI technology is pushing into IT I was wondering myself, as an “infrastructure container kubernetes guy”, how get this fancy AI technology get managed from an infrastructure operational view? Is it possible to apply our lovely cloud native principals as well? What benefit’s both technologies could bring to each other?
Let me take this questions and provide you a short journey through existing deployment models and use cases for AI software. On practical examples, we discuss what cloud/on-premise strategy we may need for applying it to our own infrastructure to get it to work from an enterprise perspective. I want to give an overview about infrastructure requirements and technologies, what could be beneficial or limiting your AI use cases in an enterprise environment. An interactive Demo will give you some insides, what approaches I got already working for real.
GraphRAG is All You need? LLM & Knowledge GraphGuy Korland
Guy Korland, CEO and Co-founder of FalkorDB, will review two articles on the integration of language models with knowledge graphs.
1. Unifying Large Language Models and Knowledge Graphs: A Roadmap.
https://arxiv.org/abs/2306.08302
2. Microsoft Research's GraphRAG paper and a review paper on various uses of knowledge graphs:
https://www.microsoft.com/en-us/research/blog/graphrag-unlocking-llm-discovery-on-narrative-private-data/
Epistemic Interaction - tuning interfaces to provide information for AI supportAlan Dix
Paper presented at SYNERGY workshop at AVI 2024, Genoa, Italy. 3rd June 2024
https://alandix.com/academic/papers/synergy2024-epistemic/
As machine learning integrates deeper into human-computer interactions, the concept of epistemic interaction emerges, aiming to refine these interactions to enhance system adaptability. This approach encourages minor, intentional adjustments in user behaviour to enrich the data available for system learning. This paper introduces epistemic interaction within the context of human-system communication, illustrating how deliberate interaction design can improve system understanding and adaptation. Through concrete examples, we demonstrate the potential of epistemic interaction to significantly advance human-computer interaction by leveraging intuitive human communication strategies to inform system design and functionality, offering a novel pathway for enriching user-system engagements.
2. METHODOLOGY
Both primary and secondary research methodologies were used
in preparing this study. Initially, a comprehensive and exhaustive
search of the literature on this industry was conducted. These
sources included related books and journals, trade literature,
marketing literature, other product/promotional literature, annual
reports, security analyst reports, and other publications.
Subsequently, telephone interviews or email correspondence
was conducted with marketing executives etc. Other sources
included related magazines, academics, and consulting
companies.
INFORMATION SOURCES
The primary information sources include Company Reports,
and National Bureau of Statistics of China etc.
STUDY GOAL AND OBJECTIVES
This report provides the industry executives with strategically significant
competitor information, analysis, insight and projection on the
competitive pattern and key companies in the industry, crucial to the
development and implementation of effective business, marketing and
R&D programs.
REPORT OBJECTIVES
To establish a comprehensive, factual, annually updated and cost-
effective information base on market size, competition patterns,
market segments, goals and strategies of the leading players in the
market, reviews and forecasts.
To assist potential market entrants in evaluating prospective
acquisition and joint venture candidates.
To complement the organizations’ internal competitor information
gathering efforts with strategic analysis, data interpretation and
insight.
To suggest for concerned investors in line with the current
development of this industry as well as the development tendency.
To help company to succeed in a competitive market, and
understand the size and growth rate of any opportunity.
Room 502, Block 3, Tower C, Changyuan Tiandi Building, No. 18, Suzhou Street, Haidian District, Beijing, China 100080
Phone: +86 10 82600828 ● Fax: +86 10 82601570 ● www.researchinchina.com ● report@researchinchina.com
Copyright 2012 ResearchInChina
3. Abstract
3D printing (also called additive manufacturing) is a technology
with which, based on digital model file, to fabricate objects by
using binding materials like plastic or metal powder and through
layer-by-layer printing. It is widely used in many fields such as
manufacturing, medical treatment, education, archaeology,
architecture, and military.
Since 2010, the global 3D printing market has been in a period of
rapid development, with an AAGR of 30% or so. In 2014, the
market size totaled USD4.1 billion. 3D printing mainly involves
software, equipment, materials and service, of which 3D printing
equipment accounted for about 46.5% in the industry in 2014.
3D printing equipment can be roughly divided into two categories,
personal and industrial. The personal 3D printers, whose prices
are relatively low, get chiefly used in personal DIY, education,
among others. In 2014, the global sales volume amounted to
approximately 100,000 units. By contrast, industrial 3D printers
have wide applications and are principally marketed in the United
States, Japan and Germany. Among them, the United States
occupied a market share of around 40% in 2014.
Room 502, Block 3, Tower C, Changyuan Tiandi Building, No. 18, Suzhou Street, Haidian District, Beijing, China 100080
Phone: +86 10 82600828 ● Fax: +86 10 82601570 ● www.researchinchina.com ● report@researchinchina.com
Copyright 2012ResearchInChina
Through acquisition, 3D Systems and Stratasys have become the
world’s two 3D printing giants, whose businesses cover the whole
3D printing industry chain. In terms of sales value, the two
companies swept a 34% market share in 2014. In 2014, Stratasys
acquired Solid Concept, Harvest Technologies, GrabCAD, and
Interfacial Solutions, while 3D Systems purchased Cimatron,
Simbionix, LayerWise, Laser Reproductions, Robtec, etc.
At present, China's 3D printing market is still at its initial stage, with
the industry chain to be improved. For example, some core
components and 3D printing materials for China-made 3D printing
equipment have to be imported from overseas. But 3D printing
technologies in national defense and aviation industries have
taken the lead in the world. In 2014, China’s 3D printing market
size approximated 4.65 billion. It is projected that in the following
years the market size will still grow at an average rate of around
40%, and that it will very likely exceed RMB20 billion by 2018.
In 2014, China's 3D printing market featured a rather low
concentration degree, and the number of enterprises involved was
close to 100, but mostly small-sized. The 3D printing equipment
manufacturers consist mainly of Beijing Tiertime Technology Co.,
Ltd., Hunan Farsoon High-tech Co., Ltd., and Shining 3D.
4. In recent years, as the State introduced policies incentive to the development of 3D printing industry, more and more listed companies
have entered the industry, a situation that helped integrate and develop China’s 3D printing industry. In 2014, there were more than 10
enterprises operating 3D printing business in China, mainly including Golden Laser, Sunshine Laser & Electronics, Guangdong Silver
Age Sci & Tech, Yinbang Clad Material, and Jiangsu Asia-Pacific Light Alloy Technology, etc.
Global and China 3D Printing Industry Report, 2015-2018 compiled by ResearchInChina is primarily concerned with the following:
Market size, competitive landscape and development prediction of global 3D printing industry;
Market size, competitive landscape and development prediction of China’s 3D printing industry;
Operation and 3D printing business of 26 global and Chinese 3D Printer manufacturers.
Room 502, Block 3, Tower C, Changyuan Tiandi Building, No. 18, Suzhou Street, Haidian District, Beijing, China 100080
Phone: +86 10 82600828 ● Fax: +86 10 82601570 ● www.researchinchina.com ● report@researchinchina.com
Copyright 2012ResearchInChina
5. 1 Overview of 3D Printing
1.1 Definition
1.2 Process
1.3 Technology
1.4 Application
1.5 Industry Chain
2 Global 3D Printing Market
2.1 Development History
2.2 Relevant Policies
2.3 Market Size
2.4 3D Printer
2.5 Competitive Landscape
2.6 Development Trend
3 China’s 3D Printing Market
3.1 Development History
3.2 Policies
3.3 Market Size
3.4 Competitive Landscape
4 Key Global Companies
4.1 Stratasys
Table of contents
Room 502, Block 3, Tower C, Changyuan Tiandi Building, No. 18, Suzhou Street, Haidian District, Beijing, China 100080
Phone: +86 10 82600828 ● Fax: +86 10 82601570 ● www.researchinchina.com ● report@researchinchina.com
5.1.4 Gross Margin
5.1.5 Clients and Suppliers
5.1.6 3D Printing Business
5.1.7 Development and Forecast
5.2 Beijing Beike Guangda Information
Technology Co., Ltd.
5.2.1 Profile
5.2.2 Operation
5.2.3 Revenue Structure
5.2.4 3D Printing Business
5.2.5 Development and Forecast
5.3 Zhengzhou LECAI Science and
Technology Co., Ltd.
5.3.1 Profile
5.3.2 Operation
5.3.3 Revenue Structure
5.3.4 3D Printing Business
5.3.5 Development and Forecast
5.4 Suzhou TOPRUN Electrical Equipment
Co. Ltd.
5.4.1 Profile
5.4.2 Operation
5.4.3 Revenue Structure
5.4.4 3D Printing Business
4.1.1 Profile
4.1.2 Operation
4.1.3 Revenue Structure
4.1.4 Profit Structure
4.1.5 3D Printing Business
4.2 3D Systems
4.2.1 Profile
4.2.2 Operation
4.2.3 Revenue Structure
4.2.4 Profit Structure
4.2.5 3D Printing Business
4.3 Others
4.3.1 Cimatron
4.3.2 Autodesk
4.3.3 Materialise
4.3.4 Arcam
4.3.5 Envisiontec
5 Key Chinese Enterprises
5.1 Shining 3D
5.1.1 Profile
5.1.2 Operation
5.1.3 Revenue Structure
6. 5.4.5 Development and Forecast
5.5 Shenzhen Sunshine Laser & Electronics
Technology Co., Ltd.
5.5.1 Profile
5.5.2 Operation
5.5.3 Revenue Structure
5.5.4 Gross Margin
5.5.5 3D Printing Business
5.5.6 Development and Forecast
5.6 Golden Laser
5.6.1 Profile
5.6.2 Operation
5.6.3 Revenue Structure
5.6.4 Gross Margin
5.6.5 3D Printing Business
5.6.6 Development and Forecast
5.7 Yinbang Clad Material Co., Ltd.
5.7.1 Profile
5.7.2 Operation
5.7.3 3D Printing Business
5.8 Guangdong Silver Age Sci & Tech Co., Ltd.
5.8.1 Profile
5.8.2 Operation
Table of contents
Room 502, Block 3, Tower C, Changyuan Tiandi Building, No. 18, Suzhou Street, Haidian District, Beijing, China 100080
Phone: +86 10 82600828 ● Fax: +86 10 82601570 ● www.researchinchina.com ● report@researchinchina.com
5.8.2 Operation
5.8.3 3D Printing Business
5.9 Jiangsu Asia-Pacific Light Alloy
Technology Co., Ltd.
5.10 SJEC Corporation
5.10.1 Profile
5.10.2 Operation
5.10.3 3D Printing Business
5.11 Fujian Haiyuan Automatic Equipments
Co., Ltd.
5.11.1 Profile
5.11.2 Operation
5.11.3 3D Printing Business
5.12 SIASUN Robot & Automation Co., Ltd.
5.12.1 Profile
5.12.2 Operation
5.12.3 3D Printing Business
5.13 Nanfang Ventilator Co., Ltd
5.13.1 Profile
5.13.2 Operation
5.13.3 3D Printing Business
5.14 Zhejiang Yasha Decoration Co., Ltd.
5.14.1 Profile
5.14.2 Operation
5.14.3 3D Printing Business
5.15 Other Companies
5.15.1 Beijing Tiertime Technology Co., Ltd.
5.15.2 Hunan Farsoon High-tech Co., Ltd.
5.15.3 Shenzhen Aurora Technology Co.,
Ltd
5.15.4 Wuhan Binhu Mechanical & Electrical
Co. Ltd.
5.15.5 Beijing Longyuan AFS
6 Conclusion and Anticipation
6.1 Conclusion
6.2 Development Prediction
6.2.1 Global
6.2.2 China
7. • Procedure of 3D Printing Operation
• Main 3D Printing Technologies, Materials, and Representative Companies
• Comparison of 3D Printing Technology and Manufacturing Technology
• Advantage and Disadvantage of 3D Printing Technology
• 3D Printing Applications
• 3D Printing Industry Chain
• Development History of 3D Printing
• Global 3D Printing Application Cases
• Polices on 3D Printing in Major Countries
• Market Size and Growth Rate of Global 3D Printing, 2005-2014
• Proportion of Different Links of Global 3D Printing Industry by Market Size, 2014
• Global Sales Volume of Personal 3D Printers, 2009-2014
• Distribution of 3D Printers Worldwide by Application, 2014
• Global Distribution of Industrial 3D Printers by Sales Value, 2014
• Global Distribution of Industrial 3D Printers by Output Value, 2014
• Main Business Models of Global 3D Printing
• Major Global 3D Printing Enterprises by Category
• Development Trend of Global 3D Printing Industry
• Major Chinese 3D Printing Enterprises and Their R&D Teams
• Development History of 3D Printing Industry in China
• Market Size and Growth Rate of 3D Printing in China, 2012-2014
• Listed 3D Printing Companies in China and Related Business, 2014
• 3D Printing Enterprises Listed in China’s New OTC Market and Related Business, 2014
• 3D Printing Equipment Manufacturers in China, 2014
Selected Charts
Room 502, Block 3, Tower C, Changyuan Tiandi Building, No. 18, Suzhou Street, Haidian District, Beijing, China 100080
Phone: +86 10 82600828 ● Fax: +86 10 82601570 ● www.researchinchina.com ● report@researchinchina.com
8. • Stratasys’ Net Revenue and Net Income, 2010-2014
• Stratasys’ Revenue by Product, 2012-2014
• Revenue Structure of Stratasys by Product, 2012-2014
• Revenue of Stratasys by Region, 2012-2014
• Revenue Structure of Stratasys by Region, 2012-2014
• Stratasys’ Gross Profit by Product, 2012-2014
• Gross Profit Proportion of Stratasys by Product, 2012-2014
• Stratasys’ Gross Margin by Product, 2012-2014
• Development History of Stratasys’ 3D Printing Business
• Stratasys’ 3D Printer Series
• Stratasys’ Global Arms
• 3D Systems’ Net Revenue and Net Income, 2010-2014
• Revenue of 3D Systems by Product, 2012-2014
• Revenue Structure of 3D Systems by Product, 2012-2014
• Revenue of 3D Systems by Region, 2012-2014
• Revenue Structure of 3D Systems by Region, 2012-2014
• 3D Systems’ Gross Profit by Product, 2012-2014
• Gross Profit Proportion of 3D Systems by Product, 2012-2014
• Development History of Stratasys’ 3D Printing Business
• 3D Systems’ Product Series
• 3D Systems’ Global Arms
• Revenue and Net Income of Shining 3D, 2012-2014
• Revenue of Shining 3D by Product, 2012-2014
• Revenue Structure of Shining 3D by Product, 2012-2014
Selected Charts
Room 502, Block 3, Tower C, Changyuan Tiandi Building, No. 18, Suzhou Street, Haidian District, Beijing, China 100080
Phone: +86 10 82600828 ● Fax: +86 10 82601570 ● www.researchinchina.com ● report@researchinchina.com
9. • Revenue of Shining 3D by Region, 2012-2013
• Revenue Structure of Shining 3D by Region, 2012-2013
• Shining 3D’s Gross Margin for Main Products, 2012-2013
• Name List and Revenue Contribution of Shining 3D’s Top 5 Clients,2013
• Shining 3D’s Main Raw Materials and Suppliers
• Name List and Procurement of Shining 3D’s Top 5 Suppliers, 2013
• Shining 3D’s 3D Printing-related Business
• Development History of Shining 3D’s 3D Printing Business
• Revenue of Shining 3D by Application, 2012-2013
• Revenue Structure of Shining 3D by Application, 2012-2013
• Shining 3D’s 3D Printing Partners
• Revenue and Net Income of Shining 3D, 2014-2018E
• Revenue and Net Income of Beike Guangda, 2012-2014
• Revenue of Beike Guangda by Product, 2012-2014
• Revenue Structure of Beike Guangda by Product, 2012-2014
• Beike Guangda’s 3D Printing Business Development Trends
• Revenue and Net Income of Beike Guangda, 2014-2018E
• Revenue and Net Income of LECAI, 2012-2014
• Revenue of LECAI by Product, 2012-2014
• Revenue Structure of LECAI by Product, 2012-2014
• Revenue and Net Income of LECAI, 2014-2018E
• Revenue and Net Income of Suzhou TOPRUN Electrical Equipment, 2012-2014
• Revenue of Suzhou TOPRUN Electrical Equipment by Product, 2012-2014
• Revenue Structure of Suzhou TOPRUN Electrical Equipment by Product, 2012-2014
Selected Charts
Room 502, Block 3, Tower C, Changyuan Tiandi Building, No. 18, Suzhou Street, Haidian District, Beijing, China 100080
Phone: +86 10 82600828 ● Fax: +86 10 82601570 ● www.researchinchina.com ● report@researchinchina.com
10. • Revenue and Net Income of Suzhou TOPRUN Electrical Equipment, 2014-2018E
• Revenue and Net Income of Sunshine Laser & Electronics, 2010-2014
• Revenue Structure of Sunshine Laser & Electronics by Product, 2014
• Revenue of Sunshine Laser & Electronics by Region, 2013-2014
• Revenue Structure of Sunshine Laser & Electronics by Region, 2013-2014
• Sunshine Laser & Electronics’ Gross Margin for Main Products, 2014
• Revenue and Net Income of Sunshine Laser & Electronics, 2014-2018E
• Revenue and Net Income of Golden Laser, 2010-2014
• Revenue of Golden Laser by Product, 2012-2014
• Revenue Structure of Golden Laser by Product, 2012-2014
• Revenue of Golden Laser by Region, 2012-2014
• Revenue Structure of Golden Laser by Region, 2012-2014
• Golden Laser’s Gross Margin for Main Products, 2012-2014
• Development of Golden Laser’s 3D Printing Business, 2014-2015
• Operation of Wuhan Loodii Creative Culture Communication, 2014
• Revenue and Net Income of Golden Laser’s 3D Printing Subsidiaries, 2014
• Revenue and Net Income of Golden Laser, 2014-2018E
• Revenue and Net Income of Yinbang Clad Material, 2010-2014
• Revenue and Net Income of FalconTech, 2013-2014
• Revenue and Net Income of Wuxi Yinbang Precision Manufacturing, 2013-2014
• Revenue and Net Income of Silver Age Sci & Tech, 2010-2014
• Revenue and Net Income of Jiangsu Asia-Pacific Light Alloy Technology, 2010-2014
• Revenue and Net Income of SJEC Corporation, 2010-2014
• Revenue and Net Income of Fujian Haiyuan Automatic Equipments, 2010-2014
Selected Charts
Room 502, Block 3, Tower C, Changyuan Tiandi Building, No. 18, Suzhou Street, Haidian District, Beijing, China 100080
Phone: +86 10 82600828 ● Fax: +86 10 82601570 ● www.researchinchina.com ● report@researchinchina.com
11. • Revenue and Net Income of Haiyuan Three Dimensional, 2013-2014
• Revenue and Net Income of SIASUN Robot & Automation, 2010-2014
• Revenue and Net Income of Nanfang Ventilator, 2010-2014
• Revenue and Net Income of Yasha Decoration, 2010-2014
• Development of Yingchuang’s 3D Printing Business,
• Revenue and Net Income of Yingchuang, 2013-2014
• Revenue of Major Global and Chinese 3D Printing Enterprises, 2014
• Market Size of 3D Printing Industry Worldwide, 2014-2018E
• Sales Volume of Personal 3D Printers Worldwide, 2014-2018E
• Market Size of 3D Printing Industry in China, 2014-2018E
Selected Charts
Room 502, Block 3, Tower C, Changyuan Tiandi Building, No. 18, Suzhou Street, Haidian District, Beijing, China 100080
Phone: +86 10 82600828 ● Fax: +86 10 82601570 ● www.researchinchina.com ● report@researchinchina.com
12. You can place your order in the following alternative ways:
1.Order online at www.researchinchina.com
2.Fax order sheet to us at fax number:+86 10 82601570
3. Email your order to: report@researchinchina.com
4. Phone us at +86 10 82600828/ 82601561
Party A:
Name:
Address:
Contact Person: Tel
E-mail: Fax
Party B:
Name: Beijing Waterwood Technologies Co., Ltd (ResearchInChina)
Address: Room 502, Block 3, Tower C, Changyuan Tiandi Building, No. 18,
Suzhou Street, Haidian District, Beijing, China 100080
Contact
Person:
Liao Yan Phone: 86-10-82600828
E-mail: report@researchinchina.com Fax: 86-10-82601570
Bank details: Beneficial Name: Beijing Waterwood Technologies Co., Ltd
Bank Name: Bank of Communications, Beijing Branch
Bank Address: NO.1 jinxiyuan shijicheng,Landianchang,Haidian
District,Beijing
Bank Account No #: 110060668012015061217
Routing No # : 332906
Bank SWIFT Code: COMMCNSHBJG
Title Format Cost
Total
Choose type of format
PDF (Single user license) …………..2,300 USD
Hard copy ………………….……. 2,500 USD
PDF (Enterprisewide license)…....... 3,500 USD
※ Reports will be dispatched immediately
once full payment has been received.
Payment may be made by wire transfer or
credit card via PayPal.
How to Buy
Room 502, Block 3, Tower C, Changyuan Tiandi Building, No. 18, Suzhou Street, Haidian District, Beijing, China 100080
Phone: +86 10 82600828 ● Fax: +86 10 82601570 ● www.researchinchina.com ● report@researchinchina.com
13. About ResearchInChina
ResearchInChina (www.researchinchina.com) is a leading independent provider of China business intelligence. Our
research is designed to meet the diverse planning and information needs of businesses, institutions, and professional
investors worldwide. Our services are used in a variety of ways, including strategic planning, product and sales forecasting,
risk and sensitivity management, and as investment research.
Our Major Activities
Multi-users market reports
Database-RICDB
Custom Research
Company Search
RICDB (http://www.researchinchina.com/data/database.html ), is a visible financial data base presented by map and graph
covering global and China macroeconomic data, industry data, and company data. It has included nearly 500,000 indices
(based on time series), and is continuing to update and increase. The most significant feature of this base is that the vast
majority of indices (about 400,000) can be displayed in map.
After purchase of our report, you will be automatically granted to enjoy 2 weeks trial service of RICDB for free.
After trial, you can decide to become our formal member or not. We will try our best to meet your demand. For more
information, please find at www.researchinchina.com
For any problems, please contact our service team at:
Room 502, Block 3, Tower C, Changyuan Tiandi Building, No. 18, Suzhou Street, Haidian District, Beijing, China 100080
Phone: +86 10 82600828 ● Fax: +86 10 82601570 ● www.researchinchina.com ● report@researchinchina.com
RICDB service