CADFEM Information Day
Begin: 10:00 am
End: 5:00 pm
Fee: Free of charge
• Reception and introduction of CADFEM
• Simulation-Driven-Product-Development
• Drive engineering
- Simulation based design of electric drives
·
Example: permanently excited synchronous machine
·
Cogging torques, inductivities, start-up behavior
- Loss assessment of electric drives
·
Eddy current, iron and copper losses
·
Time and frequency coupling
- Electric machine acoustics
· Example: transient, DFT
• Electromechanical systems
- Abstraction of system description (analytics, COSIM, ROM)
- Modeling of sensor systems (incremental encoders)
- Control (speed control of a drive, PWM)
• Automation technology
- Sensors and control systems
- Interference on wires
· Determination of concentrated parameters
· Mains pollution
· Parasitic effects
Register ar http://www.cadfem.at/produkte/infoveranstaltungen/infotage/s/11885.html
Taashee is a 100% Linux and Open source software (OSS) company. Taashee uniquely offers a one-stop solution for all Linux and OSS related projects. We have a dedicated team of certified Linux engineers and passionate developers to handle any kind of projects related to implementation or development on Linux.
Taashee helps its customers to fully utilize the power of Linux and Open Source technologies. This results in, higher stability, higher security and higher performance with lower cost and lesser administrative overheads compared to Microsoft based solution. Even for long-time Unix users, who are stuck with limited and proprietary solutions, we offer migration services to switch over to Enterprise-grade Red Hat.
We specialize in high-availability and high-performance clusters; remote and on-site system management and maintenance services; Linux consulting services; Druid and Asterisk based VoIP solutions; Telco-grade Mail servers with uptime of as much as 99.999%; Application design and development using Open Source Technologies. Besides this, we provide comprehensive Jboss related services like: Development, Deployment, Clustering, Production-level optimization, Security etc & also Virtualization.
Taashee is a 100% Linux and Open source software (OSS) company. Taashee uniquely offers a one-stop solution for all Linux and OSS related projects. We have a dedicated team of certified Linux engineers and passionate developers to handle any kind of projects related to implementation or development on Linux.
Taashee helps its customers to fully utilize the power of Linux and Open Source technologies. This results in, higher stability, higher security and higher performance with lower cost and lesser administrative overheads compared to Microsoft based solution. Even for long-time Unix users, who are stuck with limited and proprietary solutions, we offer migration services to switch over to Enterprise-grade Red Hat.
We specialize in high-availability and high-performance clusters; remote and on-site system management and maintenance services; Linux consulting services; Druid and Asterisk based VoIP solutions; Telco-grade Mail servers with uptime of as much as 99.999%; Application design and development using Open Source Technologies. Besides this, we provide comprehensive Jboss related services like: Development, Deployment, Clustering, Production-level optimization, Security etc & also Virtualization.
"Genetic Testing: Do You Really Want To Know What's In Your Genes?"
This Science Pub took place at the Bagdad Theater in Portland, Oregon, on Monday, July 6, 2009. It was presented by Dr. Lisa Sardinia, Associate Professor at Pacific University and Associate director of the Pacific Institute for Ethics and Social Policy.
http://www.pacificu.edu/as/biology/faculty/sardinia.cfm
Taashee is a 100% Linux and Open source software (OSS) company. Taashee uniquely offers a one-stop solution for all Linux and OSS related projects. We have a dedicated team of certified Linux engineers and passionate developers to handle any kind of projects related to implementation or development on Linux.
Taashee helps its customers to fully utilize the power of Linux and Open Source technologies. This results in, higher stability, higher security and higher performance with lower cost and lesser administrative overheads compared to Microsoft based solution. Even for long-time Unix users, who are stuck with limited and proprietary solutions, we offer migration services to switch over to Enterprise-grade Red Hat.
We specialize in high-availability and high-performance clusters; remote and on-site system management and maintenance services; Linux consulting services; Druid and Asterisk based VoIP solutions; Telco-grade Mail servers with uptime of as much as 99.999%; Application design and development using Open Source Technologies. Besides this, we provide comprehensive Jboss related services like: Development, Deployment, Clustering, Production-level optimization, Security etc & also Virtualization.
Taashee is a 100% Linux and Open source software (OSS) company. Taashee uniquely offers a one-stop solution for all Linux and OSS related projects. We have a dedicated team of certified Linux engineers and passionate developers to handle any kind of projects related to implementation or development on Linux.
Taashee helps its customers to fully utilize the power of Linux and Open Source technologies. This results in, higher stability, higher security and higher performance with lower cost and lesser administrative overheads compared to Microsoft based solution. Even for long-time Unix users, who are stuck with limited and proprietary solutions, we offer migration services to switch over to Enterprise-grade Red Hat.
We specialize in high-availability and high-performance clusters; remote and on-site system management and maintenance services; Linux consulting services; Druid and Asterisk based VoIP solutions; Telco-grade Mail servers with uptime of as much as 99.999%; Application design and development using Open Source Technologies. Besides this, we provide comprehensive Jboss related services like: Development, Deployment, Clustering, Production-level optimization, Security etc & also Virtualization.
"Genetic Testing: Do You Really Want To Know What's In Your Genes?"
This Science Pub took place at the Bagdad Theater in Portland, Oregon, on Monday, July 6, 2009. It was presented by Dr. Lisa Sardinia, Associate Professor at Pacific University and Associate director of the Pacific Institute for Ethics and Social Policy.
http://www.pacificu.edu/as/biology/faculty/sardinia.cfm
Smart deployment of Finite Element Analysis
The TCS engineering department increasingly deploys Finite Element Analysis (FEA) as a method
of optimising the detailed design of steel structures. “FEA is particularly useful in complex projects,
for example calculating irregular-shaped joints,” says TCS Head of Engineering Peter Neven.
KEY FACTS
• TCS increasingly uses Finite Element Analysis
(FEA) in designing steel structures.
• FEA is used typically in smart combination
with hand calculation methods.
• Projects include Canary Wharf Station and the
new giant Stageco performance stage due to
tour this summer.
ANSYS AIM her mühendisin kolaylıkla kullanabilmesi için tasarlanmış, pratik ve güçlü bir multi-fizik simulasyon platformudur. ANSYS Release 17.1 ile ANSYS Mechanical Enterprise müşterileri için ücretsiz olarak kullanılabilmektedir. Bilgi için info@anova.com.tr adresinden bizimle iletişime geçebilirsiniz.
This presentation introduces the concepts of mechatronic system simulation, and the LMS Imagine.Lab Amesim software.
For more information, please visit our website: www.siemens.com/plm/simcenter-amesim
RTaW SysML Companion transforms SysML models into VHDL/AMS so that it becomes possible to simulate SysML models. SysML Companion enables to perform virtual prototyping and derive tests very early in the design phase directly from SysML specification. To the best of our knowledge, SysML Companion is the first tool of its kind.
3d printer electronics engineering live projects abstracts @1000KV Technologi...1000kv technologies
electronics engineering live projects abstracts
electronics projects, electronics projects for engineering final year students, electronics and communication engineering projects for final year students,100kv,1000kv,1000kv technologies,1000kv projects,technologies,live projects,Hyderabad live projects,live projects in, diploma low cost projects,1000kv projects, , academic projects,btech live projects,Hyderabad,1000kilovolts,1000kilovolts technologies ,btech main projects ,
INDUCTION MACHINES ANALYSIS USING LABVIEW SOFTWARE PACKAGE _Ijmet 10 04_085Isaac Samuel
Induction machines are widely used in many industries due to their robustness, ruggedness and easy maintenance feature. Due to the addition of power electronics devices and the complexity involved in the design of induction machines, their study and analysis can be very difficult. The use of software packages has been widely adopted to analyze and study the behaviours of induction machines. This work focused on the use
of an engineering software package known as Laboratory Virtual Instrument Engineering Workbench (LabVIEW). It is used in this work to study the behaviour and characteristics of induction machines. LabVIEW was utilized due to its cheap and userfriendly feature. This work shows that induction machines can be completely analyzed using related mathematical equations for performance analysis.
Wir freuen uns, Sie bei der CADFEM ANSYS Simulation Conference auch 2017 wieder in der voestalpine Stahlwelt in Linz begrüßen zu dürfen. Die CADFEM (Austria) GmbH sowie zahlreiche Aussteller präsentieren branchenübergreifend das komplette Simulationsspektrum aus der Struktur- und Strömungsmechanik, Elektromagnetik, Systemsimulation und Multiphysik.
Die Konferenz ist mit 200 Gästen an zwei Konferenztagen einer der wichtigsten CAE-Branchentreffpunkte in Österreich. Lassen Sie uns gemeinsam über CAE im Allgemeinen und die Programmfamilie von ANSYS im Besonderen diskutieren. Wie immer in einer entspannten und motivierenden Atmosphäre! Sowohl Neueinsteiger, als auch erfahrene Simulationsanwender sind herzlich eingeladen.
ANSYS in der Praxis:
Multiphysik-Simulationen für die Auslegung elektrischer Antriebe
Hilite profitiert vom verstärkten Ausbau der Simulation
Simulation mit System: Interview mit Prof. Dr.-Ing. Christian Sleziona von Hilite
Neue Konzepte analysieren und bewerten
Wärmemanagement in der virtuellen Produktentwicklung mit Icepak
Analyse der Verformung von feinjustierbaren Reibahlen
Optimierung von Faserverbundbauteilen im Segelrennsport
REAL4HYBRID: Auslegung von Fügeverbindungen an Hybridstrukturen
Rieter sorgt für mehr Energieeffizienz
More Related Content
Similar to CADFEM Information Day: Drives and automation engineering
Smart deployment of Finite Element Analysis
The TCS engineering department increasingly deploys Finite Element Analysis (FEA) as a method
of optimising the detailed design of steel structures. “FEA is particularly useful in complex projects,
for example calculating irregular-shaped joints,” says TCS Head of Engineering Peter Neven.
KEY FACTS
• TCS increasingly uses Finite Element Analysis
(FEA) in designing steel structures.
• FEA is used typically in smart combination
with hand calculation methods.
• Projects include Canary Wharf Station and the
new giant Stageco performance stage due to
tour this summer.
ANSYS AIM her mühendisin kolaylıkla kullanabilmesi için tasarlanmış, pratik ve güçlü bir multi-fizik simulasyon platformudur. ANSYS Release 17.1 ile ANSYS Mechanical Enterprise müşterileri için ücretsiz olarak kullanılabilmektedir. Bilgi için info@anova.com.tr adresinden bizimle iletişime geçebilirsiniz.
This presentation introduces the concepts of mechatronic system simulation, and the LMS Imagine.Lab Amesim software.
For more information, please visit our website: www.siemens.com/plm/simcenter-amesim
RTaW SysML Companion transforms SysML models into VHDL/AMS so that it becomes possible to simulate SysML models. SysML Companion enables to perform virtual prototyping and derive tests very early in the design phase directly from SysML specification. To the best of our knowledge, SysML Companion is the first tool of its kind.
3d printer electronics engineering live projects abstracts @1000KV Technologi...1000kv technologies
electronics engineering live projects abstracts
electronics projects, electronics projects for engineering final year students, electronics and communication engineering projects for final year students,100kv,1000kv,1000kv technologies,1000kv projects,technologies,live projects,Hyderabad live projects,live projects in, diploma low cost projects,1000kv projects, , academic projects,btech live projects,Hyderabad,1000kilovolts,1000kilovolts technologies ,btech main projects ,
INDUCTION MACHINES ANALYSIS USING LABVIEW SOFTWARE PACKAGE _Ijmet 10 04_085Isaac Samuel
Induction machines are widely used in many industries due to their robustness, ruggedness and easy maintenance feature. Due to the addition of power electronics devices and the complexity involved in the design of induction machines, their study and analysis can be very difficult. The use of software packages has been widely adopted to analyze and study the behaviours of induction machines. This work focused on the use
of an engineering software package known as Laboratory Virtual Instrument Engineering Workbench (LabVIEW). It is used in this work to study the behaviour and characteristics of induction machines. LabVIEW was utilized due to its cheap and userfriendly feature. This work shows that induction machines can be completely analyzed using related mathematical equations for performance analysis.
Wir freuen uns, Sie bei der CADFEM ANSYS Simulation Conference auch 2017 wieder in der voestalpine Stahlwelt in Linz begrüßen zu dürfen. Die CADFEM (Austria) GmbH sowie zahlreiche Aussteller präsentieren branchenübergreifend das komplette Simulationsspektrum aus der Struktur- und Strömungsmechanik, Elektromagnetik, Systemsimulation und Multiphysik.
Die Konferenz ist mit 200 Gästen an zwei Konferenztagen einer der wichtigsten CAE-Branchentreffpunkte in Österreich. Lassen Sie uns gemeinsam über CAE im Allgemeinen und die Programmfamilie von ANSYS im Besonderen diskutieren. Wie immer in einer entspannten und motivierenden Atmosphäre! Sowohl Neueinsteiger, als auch erfahrene Simulationsanwender sind herzlich eingeladen.
ANSYS in der Praxis:
Multiphysik-Simulationen für die Auslegung elektrischer Antriebe
Hilite profitiert vom verstärkten Ausbau der Simulation
Simulation mit System: Interview mit Prof. Dr.-Ing. Christian Sleziona von Hilite
Neue Konzepte analysieren und bewerten
Wärmemanagement in der virtuellen Produktentwicklung mit Icepak
Analyse der Verformung von feinjustierbaren Reibahlen
Optimierung von Faserverbundbauteilen im Segelrennsport
REAL4HYBRID: Auslegung von Fügeverbindungen an Hybridstrukturen
Rieter sorgt für mehr Energieeffizienz
Das CADFEM Journal berichtet zweimal jährlich aus der CAE-Praxis und liefert theoretisch-wissenschaftliche Beiträge. Die aktuelle Ausgabe präsentiert zum Thema "Simulation verbindet" u.a. Artikel zu Signalübertragung: Antennen und Leiterplatten; Baugruppen: Kleben, Schweißen, Schrauben;
Physikalische Domänen: Feld- und Systemsimulation. Aus dem Inhalt: Elektromagnetik – Simulation von Antennen. Elektromagnetik – HF-Simulation der Leiterplatte zur Layout-Optimierung. Artikelreihe zu Fügetechniken Kleben, Schweißen und Schrauben. Systemsimulation: Optimierte Produktentwicklung durch gekoppelte Feld- und Systemsimulation.
Simulation of a fatigue crack problem in electronic devicesCADFEM Austria GmbH
Fatigue crack growth under active cycling conditions is simulated using the cohesive zone modeling concept within the framework of the Finite Element Method.
To this end, a cyclic cohesive zone model based on a damage evolution equation is extended onto the case of transient thermal loading conditions and is implemented into ANSYS. The thermal and mechanical interaction of the cohesive surfaces is taken into account for both open and closed crack states. By incorporating the temperature dependence of the cohesive zone model parameters, the model is also extended onto cases of nonisothermal fatigue.
To speed-up fatigue simulations, the cyclic cohesive zone model is equipped with the cycle jump technique based on direct iteration of the damage evolution equation.
The implemented thermomechanical cyclic cohesive zone model is applied to a problem of interfacial debonding between two layers of a power metallization stack subjected to the active thermal cycling.
Schraubenberechnung "inside"ANSYS nach der Richtlinie VDI 2230
Die Richtlinie VDI 2230 sieht einen Berechnungsablauf vor, der die Montage, die Beanspruchung unter statischen und dynamischen Lasten, die Flächenpressung sowie das Abscheren der Gewindegänge berücksichtigt. Als Nennspannungskonzept sind für den Nachweis keine Auswertungen der Spannungen aus der FEM-Analyse notwendig. Die aus der Analyse ermittelten Kräfte und Momente sind für die Verarbeitung ausreichend.
Wer diese für einen richtlinienkonformen Nachweis nutzen mochte, musste bisher selbst manuell aktiv werden: Die erforderlichen Größen aus der FEM-Berechnung mussten extrahiert, übertragen und in weiterer Folge per Tabellenkalkulation oder separater Software verarbeitet werden. Das neue Softwaremodul von CADFEM „Bolt Assessment inside ANSYS“ bietet mit einem in ANSYS Workbench integrierten Nachweis konform der VDI-Richtlinie 2230 die ideale Lösung.
Programm Fachkonferenz zur numerischen Simulation in Wien 2015CADFEM Austria GmbH
Die Fachkonferenz zur Numerischen Simulation
Der CAE-Branchentreffpunkt in Wien
Am 29. und 30. April 2015 findet mit der Fachkonferenz zur numerischen Simulation der jährliche CAE-Branchentreffpunkt in Wien statt. CADFEM Austria und ANSYS Germany laden Anwender und CAE-Interessierte herzlich ein. Die Teilnehmer erwartet viel Neues aus der Welt der Simulation: Keynote-Vorträge von HP & Intel, KTM TECHNOLOGiES und John Deere, Anwenderbeiträge aus verschiedenen Branchen und Simulationsgebieten, sowie Kompaktseminare zu aktuellen Themen. Ein attraktives Rahmenprogramm anlässlich des 10-Jahres-Jubiläums von CADFEM rundet die Konferenz ab.
Simulation in der Produktentwicklung: Anwender berichten
Computersimulationen physikalischer Eigenschaften sind in der Produktentwicklung heutzutage ein wichtiger Baustein, um sich im internationalen Wettbewerb und schnell wandelnden Märkten durchzusetzen. Ingenieure und Physiker von ATX-Unternehmen, aus der mittelständischen Industrie und hochspezialisierten Kleinunternehmen, aber auch Forschungsinstituten setzen auf diese Technologie. Anwender berichten bei der Konferenz darüber, wie sie Simulation in ihrer Produktentwicklung einsetzen. Sowohl Neueinsteiger, als auch erfahrene Simulanten kommen jedes Jahr wieder ins Staunen, wenn gezeigt wird, was Simulation alles möglich macht - und welche Potenziale noch auszuschöpfen sind. Die Konferenzteilnehmer erwartet auch ein attraktives Rahmenprogramm. Erstmals präsentieren Studierende ihre Simulationsprojekte im Rahmen einer Poster-Session. Die CAE-Fachausstellung und die Abendveranstaltung bieten die ideale Möglichkeit, interessantes Zusatzangebot kennen zu lernen und wichtige Kontakte in der CAE-Branche zu knüpfen.
Simulation lernen: Kompaktseminare für alle Level
Am zweiten Konferenztag stehen erstmals zehn halbtägige Kompaktseminare zur Auswahl. Die Seminare behandeln aktuelle Simulationsthemen für jeden Wissensstand. Interessenten ohne Vorkenntnisse bekommen mit ersten Übungen am Rechner einen Einblick in ANSYS. Fortgeschrittenen Seminare umfassen u.a. die Schraubenbewertung nach VDI 2230 oder Schweißnahtbewertung nach FKM-Richtlinie. Auch elektromagnetische, sowie strömungsmechanische Themen werden abgedeckt.
Simulation erleben: anmelden und bei der CAE-Konferenz dabei sein
Simulation macht vieles möglich. Simulationsexperten, Neueinsteiger oder Interessenten sind eingeladen, die ganze Bandbreite moderner Simulationstechnologie als Werkzeug für mehr Qualität, Innovation und Zeitersparnis in der Produktentwicklung zu erleben.
Details & Anmeldung unter http://www.usersmeeting.at
Die CADFEM (Austria) GmbH und ANSYS Germany GmbH laden herzlich zur Fachkonferenz zur numerischen Simulation nach Wien ein! Am 29. + 30. April 2015 dreht sich im Schloss Schönbrunn Tagungszentrum alles um die virtuelle Produktentwicklung. Anlässlich des 10-Jahres-Jubiläums von CADFEM Austria dürfen sich die Teilnehmer auf einige Highlights freuen.
Numerische Simulation in Österreich: Der CAE-Branchentreffpunkt
- Kostenfreier erster Konferenztag
- Keynote-Vorträge von HP und Intel, sowie zum Simulationsmanagement in der virtuellen Produktentwicklung bei John Deere
- Anwendervorträge zu Struktur- und Strömungsmechanik, sowie Elektromagnetik - Erfahren Sie, wie österreichische Top- Unternehmen Simulation erfolgreich einsetzen
- CAE-Fachausstellung
- Poster-Session mit Simulationsprojekten von Studierenden
- Abendveranstaltung in der Ottakringer Brauerei
- Erstmals 10 Kompaktseminare am 2. Konferenztag - Stellen Sie sich Ihr individuelles Programm für Vor- und Nachmittag zusammen!
Simulation im täglichen Einsatz: Anwender berichten
Bei der Konferenz kommen sowohl Neueinsteiger, als auch erfahrene Simulanten jedes Jahr wieder ins Staunen, wenn gezeigt wird, was Simulation alles möglich macht!
In Anwendervorträgen berichten Unternehmen und Forschungsinstitute über ihre tägliche Simulationsarbeit. Mit KAI Villach, Trumpf Maschinen Austria, Egston System Electronics Eggenburg oder Hottinger Baldwin Messtechnik, sowie dem AIT, Universität Innsbruck und JKU Linz konnten interessante Referenten gewonnen werden. Informieren Sie sich über eine große Bandbreite an Themen. In den Pausen besteht die Gelegenheit, bei der CAE-Fachausstellung interessantes Zusatzangebot kennen zu lernen und sich mit Kollegen und Gleichgesinnten auszutauschen.
Simulation lernen: Kompaktseminare für alle Level
Am 2. Konferenztag stehen erstmals 10 Kompaktseminare zur Auswahl. Die Besonderheit: die Teilnehmer stellen sich ihr Programm individuell zusammen! Die Seminare sind für Anwender aller Level konzipiert: vom Einsteiger-Modul mit ersten Übungen am Rechner, bis zu fortgeschrittenen Seminare zur Schraubenbewertung nach VDI 2230 oder Schweißnahtbewertung nach FKM-Richtlinie findet sich alles im Angebot. Auch elektromagnetische, sowie strömungsmechanische Themen werden abgedeckt.
Simulation erleben: Anmelden und bei der CAE-Konferenz dabei sein
CADFEM und ANSYS freuen sich darauf, Visionen und Trends zur Simulation gemeinsam mit Ihnen zu diskutieren!
Alle Informationen zu Hotels, Tagungsort, Anfahrt usw. erhalten Sie auf der Veranstaltungswebsite unter http://www.usersmeeting.at
Im Life Cycle Engineering wird genau das gemacht: alle Lebensphasen eines Produktes - beginnend bei der Konstruktion über die Produktion bis hin zur Nutzung und Wiederverwendung bzw. Recycling der Rohstoffe -werden ganzheitlich betrachtet. Wirtschaftliche, ökologische und technische Faktoren werden in die Analysen mit einbezogen. In der Präsentation werden durchgeführte Simulationsaufgaben zur Beurteilung der Nutzungsdauer bestehender Brückentragwerke vorgestellt. Diese beinhalten neben dem Ermüdungsnachweis, die Rissfortschrittsberechnung und die Simulation von Reparaturschweißungen.
Thermal and mechanical stress modelling of smart power switches under active ...CADFEM Austria GmbH
Smart power switches (SPS) for industrial and automotive applications have to withstand substantial power dissipation during operation. They are expected to work even under extreme temperature and electrical stresses, such as transient start up or overload. Several thousands of cyclic loading of electric pulses might cause failure to this SPS device. The reason behind this failure is that the electrical pulses induce thermal stress, which in turn leads to mechanical stress. Due to the multi-material design of SPS, the thermal stress often induces tractions at the material interfaces. These tractions might initiate cracks and delamination, which can lead to a device failure due to loss of electrical contact. If a crack is not nucleated, the device may fail due to overheating. Therefore, thermal and mechanical stress plays a crucial role to determine the device failure and thereby the lifetime modelling of the device. Finite Element simulation is used to analyse heat transfer and mechanical problems in SPS.
ANSYS is the FEM simulation tool which is used to perform the electrical, thermal and mechanical simulations. Electro-Thermal simulation is initially carried out in a 3D model of the SPS for various electrical pulses and as a result, the thermal stress in the model is analysed. Thermo-Mechanical chip simulation is performed with the thermal stress as loading conditions and the mechanical stress across the model is analysed. Microscopic stress simulation of the SPS sub- model is performed to analyse the stress in power metal. The electrical, thermal and the mechanical problem are solved using the FEM method in ANSYS.
Schweißverzugssimulation: Rohrplatte eines HochdruckwärmetauschersCADFEM Austria GmbH
Bei der Plattierung der Rohrplatte eines Hochdruckwärmetauschers kommt es zu einem Schweißverzug. Der eingesetzte Konus gleicht diesen aus. Im vorliegenden Projekt übernahm CADFEM den Modellaufbau und die Programmierung der notwendigen Makros für zur Berechnung der idealen Größe dieses Konus.
Die Rohrplatte eines Hochdruckwärmetauschers, welcher zur Herstellung von Harnstoff dient, wird einseitig mittels Auftragsschweißen in mehreren Durchgängen mit unterschiedlichen Materialen plattiert. Dabei kommt es zu einer nennenswerten Wärmeeinbringung und daher zu einem Schweißverzug. Um diesen auszugleichen, wird der Schmiederohteil der Rohrplatte schon in konischer Form bestellt. Abhängig von der Größe der Rohrplatte und dem eingesetzten Material wurde mittels FE-Simulation berechnet, wie groß dieser Konus sein muss.
Anmeldung & Detailinfo: http://www.cadfem.at/designverstehen
Betriebsfestigkeit eines Hüftimplantats - Spannungsberechnung und Betriebsfes...CADFEM Austria GmbH
Hüftimplantaten werden als hoch beanspruchbare Bauteile entwickelt. Nichtsdestotrotz kann es speziell am Schaftquerschnitt zu Brüchen kommen. Dieser kann nicht beliebig groß dimensioniert werden, da sonst der Bewegungsfreiraum eingeschränkt wäre.
Im vorliegenden Fall wurden durch die Verwendung von publizierten Messergebnissen von Kräften in Hüftgelenken realer Patienten sowie Vorgaben aus Prüfnormen Simulationen mit ANSYS Workbench für ein Implantat durchgeführt.
Lesen Sie mehr im Flyer anbei - bei Fragen können Sie sich jederzeit an uns wenden - christoph.schlegel@cadfem.at bzw. info@cadfem.at
Ein Algorithmus zur parameterfreien Formoptimierung und Vergleich mit kommerz...CADFEM Austria GmbH
Motivation für die Entwicklung des Algorithmus
Vorstellung des entwickelten Algorithmus
Vergleich mit parameterfreien Topologieoptimierung
Zusammenfassung und AusblickVergleich mit parameterorientierter Gestaltoptimierung
Anwendung an einem Druckgussgehäuse
Optimierungsverfahren mittels FEM
Fakten zum AB Stahlbau der Universität Innsbruck:
•Anwendung der numerischen Software ANSYS,
•Seit kurzem Einführung neuer optischer Messsysteme ARAMIS und PONTOS.
Grundidee: Anwendungsmöglichkeiten der Messsyteme ARAMIS und PONTOS testen und mit den numerischen Möglichkeiten von ANSYS vergleichen.
Ziel: Erkennen der Vor- und Nachteile der Systeme für einen optimalen Einsatz.
Inhalt:
• Kontaktmodellierung
Kontaktformulierungen in ANSYS
• Vorgehensweise bei der MKS-Modellierung
• Anwendungsbeispiele (Heckmäher, 4-Kreisel Schwader, Scheibenegge am 4-Poster)
Fazit:
Mit Hilfe der Kontaktmodellierung kann die Modellkomplexität erheblich gemindert werden
– Genauere Ergebnisse aufgrund der HEX-Modellierung
– Höhere Performance beim Postprocessing im MKS-Programm
– Weniger Vernetzungsprobleme
Bei der Pure Penalty Formulierung ergeben sich für die Starrkörperfrequenzen Werte ≠ 0, wenn Spalte bzw.
Durchdringungen zwischen den Kontaktflächen gegeben sind
– Abhilfe mittels MPC-Kontakt bzw. Kontaktelemente auf Zielfläche verschieben
Determining the Material Parameters of a Polyurethane Foam Using Numerical Op...CADFEM Austria GmbH
Komplexe numerische Simulationen werden täglich in R & D-Prozesse einbezogen.
• Grundsätzlich können Materialeigenschaften gemessen werden, aber welche Werte sollten für die Parameter der Materialmodelle in numerischen Simulationen angewendet werden?
• Wie kann man die Parameter der Materialmodelle schätzen, wenn
sie nicht direkt aus experimentellen Daten berechnet werden
können?
Finden Sie die Antwort auf diese Fragen in der folgenden Präsentation bzw. dem inkludierten Paper.
Refiner werden in der Papier- und Faserplatten-Herstellung zur Aufbereitung von Hackschnitzeln zu Faser oder Zellstoff eingesetzt. Eine genaue Berechnung von Refinern und der Scheibe ist wichtig.
Bruchmechanische Parameter in ANSYS:
* Energiefreisetzungsrate Gi über VCCT
* Spannungsintensitätsfaktor Ki über Interaktionsintegral
* J-Integral über äquivalentes Gebietsintegral
Einsatz der Drapiersimulation mittels ANSYS Composite PrePost zur Erstellung ...CADFEM Austria GmbH
Orthotropie von Faser-Kunststoff-Verbunden
Spezielle Anforderungen an die FE-Modellierung
Möglichkeiten des ANSYS Composite PrepPost 13.0
Beispielsimulationen
Simulation von Kraftwerken mit Rostfeuerung m. ANSYS Fluent & alternativem Co...CADFEM Austria GmbH
Darstellung der Temperatur-, Geschwindigkeits- und Speziesverteilungen in einer Verbrennungsanlage mit Rostfeuerung.
Simulation der Feststoffverbrennung und der Gasphasenumwandlung
Beurteilung der Sekundärlufteinbringung
Beurteilung der Strömungsverhältnisse
Simulation von Kraftwerken mit Rostfeuerung m. ANSYS Fluent & alternativem Co...
CADFEM Information Day: Drives and automation engineering
1. Information day
The whole world of simulation Drives and automation
Fluid Dynamics engineering
Structural Mechanics
➔ Thermodynamics
with ANSYS Workbench ® ™
➔ Electromagnetics
Systems and Multiphysics
Simulating electric drives and calculating the losses,
v
ibration behavior, failures and mains pollution –
engineering with ANSYS Workbench covers it all
® ™
Comprehensive ANSYS simulation software provides a number of important fea-
®
tures for analyzing electric drives and electromechanical systems. It allows users to
detect losses and vibration behavior early on in the design process, enabling them
to significantly shorten development times and create innovative solutions.
The profit of FEM-simulation software:
• Integrated design-tool chain enabling fast, accurate descriptions of electric
drive operating behavior;
• Automatic creation of three-dimensional machine models for dynamic analysis
e. g. start-up or loss assessment;
• Design optimization through parameterization and direct CAD-connection;
• Simulation of power electronics makes it possible to reproduce real operating
conditions which, amongst others, allow for the analysis of harmonic contents;
• Direct integration into ANSYS Workbench also allows for investigation of
® ™
t
hermal interaction, including CFD;
• Allows user-friendly analysis of the vibration behavior as an interaction of the
electromechanical system (including power electronics) through to acoustic
a
ssessment of drive systems.
ANSYS and integrated Simplorer and Maxwell products are industry proven and
® ® ®
t
ested ystems, enabling users to carry out the above mentioned tasks more efficiently.
s
Picture: manfredxy/istockphoto.com
ANSYS covers the full application range of
®
Target audience
simulation in the product development.
This information day has been organized for
- Design engineers of:
CADFEM as ANSYS Competence Center FEM in
· Electric drives and machines
Germany, Austria and Switzerland is in cooperation
· Magnetic switches and couplings
with ALGORITEM your partner for structural mechanics
as well as
and multiphysics in Slovenia.
- Systems developers in power electronics
and control engineering
Date and Venue
March 14, 2013 in Ljubljana
AHOTEL
Cesta dveh cesarjev 34d
1000 Ljubljana, Slovenija