1. 1 of 4
CURRICULUM VITAE
Rohith Kumar C
No. 7, 1st
“A” Cross,
V.R. Garden,
Near LIC Colony,
Yeshwanthpur, Email Id: c.rohithkumar@gmail.com
Bangalore-560022. Phone: +91 9449493727
Career Objective
To obtain a challenging position in a high quality Electrical, Electronics and Communication
Engineering environment where my resourceful experience and academic skills will add value to
organizational operations.
Area Of Expertise
 Safety testing of Electrical and electronic equipments.
 Power Electronics Devices, Circuits and Drives.
 OrCAD, PSpice Simulation, PCB Design.
 Advance Digital Signal Processing and DSP Application to Drives.
 Design and simulation of Analog circuits.
 Special electrical machines, Electrical Machines Design & Modeling.
 Modeling and simulations of Power electronics systems.
 Manual Testing.
Professional Experience
Organization: Electronics Test and Development Centre, STQC directorate,
Ministry of Communication and Information Technology,
Government of India, Bangalore.
Designation: Test Engineer.
Duration: Jan 2015 to till date
Having experience in testing of various electrical and electronics equipments as per national and
international standards where planning, implementation of test methods, analysis and troubleshooting
are involved.
 Safety Testing
Carried out electrical safety testing of various electrical and electronic equipments under
Compulsory registration scheme(CRS), Non CRS and Surveillance tests of equipments under standards
mentioned below

2. 2 of 4
 Information Technology Equipment as per IEC 60950-1:2005+A1:2009+A2: 2013 / IS 13252
(Part 1):2010+A1:2013+A2:2015.
 Uninterruptible Power Supply as per IEC 62040-1:2008/ IS16242 (Part1):2014.
 Audio, video and similar electronic apparatus as per IEC 60065:2005/ IS616:2010.
 Safety test of Household and similar Electrical Appliances (Microwave Ovens, including
combination microwave ovens) as per IEC 60335-2-25/ IS302-2-25:2014.
 Carried out On-site testing as per safety standard IEC 60204-1:2005 +A1:2008 of Electrical
equipment of machines.
 Carried out PT/ILC.
 Successfully demonstrated various test during NABL Audit 2016 at ETDC, Bangalore.
 Successfully demonstrated various test during BIS Audit 2015 at ETDC, Bangalore.
 Environmental Simulation Testing
Carried out environmental testing of various electrical and electronic products as per National and
International standards (IEC 60068, MIL-STD-810, MIL-STD-202, JSS-55555, JSS-50101, IS 9000,
QM333).
 Climatic Tests like Cold Test, High Temperature Test, Temperature Cyclic Test, Damp Heat
Steady State/Cyclic Test, Thermal Shock Test, Corrosion (Salt Spray) Test
 Durability Test Methods: Vibration Test, Bump Test, Drop Test.
 Evaluation of test result and preparation of test reports
 Laboratory management as per lab QMS including maintenance of laboratory documents, up
keeping of records, In-Service Checks, Lab Environmental conditions and periodic calibration etc.
Certification Courses and Internship
 Laboratory management system and internal audit course as per ISO/IEC 17025:2005.
 ”Electronic Design andAutomation” course from CADD center, Mangalore.
(OrCAD, PSpice Simulation, PCB Designing)
 “BSNL, Mangalore – Mobile communication and Internet” undergone an training from
21/02/2012 to 03/03/2012
 “KIOCL, Mangalore - Pellet Plant Unit” undergone one month internship during June 2011.

3. 3 of 4
Education Profile
2014: M.Tech (Computer application in industrial drives) from The Oxford College of Engineering,
Bangalore. Affiliated to VTU, Belgaum with an aggregate of 70%.
2012: B.E. (Electronics and communication engineering) from Shree Devi Institute of Technology,
Mangalore. Affiliated to VTU, Belgaum with an aggregate of 67%.
2008: PUC from Sharada Indp PU College, Mangalore with 64%.
2006: SSLC from Christha Jyothi High School, Arakalgud with 84%.
Academic Project
 Implementation of Field Oriented Control for PMSM Drive based on TMS320F28035 DSP
Controller
Softwares Used: CCS 5.4, OrCAD and PSpice.
Description: The implementation of the Permanent magnet synchronous motor (PMSM)
controller by using Field Oriented Control (FOC) method. The digital signal processor (DSP) was
used as a controller to interface between the FOC and the PMSM. In this project, a 32 bit DSP
controller TMS320F28035 is used to realize the drive system. TMDSHVMTRPFCKIT board by Texas
Instrument is used to run the motor
 Surface Irregularity Monitoring System
Softwares Used: Keil μVision3 IDE and OrCAD.
Description: This system is designed mainly on a vision to provide safety for passengers, their
vehicle and co-vehicle sharing the road. This model is more help full during rainy and snow
condition. On the basics of the behaviour of sensors which are fixed at the front end of vehicle (i.e.
delay in receiving signal) the controller will decide the condition of road and alert the driver of the
vehicle.
Software Proficiency
 Programming languages and tools: LabVIEW, VHDL, Verilog, MATLAB, CCS, Programming of
8051µC, Basics of C, Java and Manual Testing.
 Operating systems: Windows 8 and earlier versions.

4. 4 of 4
Extra-Curricular Activities
 A paper entitled “Implementation of Field Oriented Control for PMSM Drive Based on
TMS320F28035 DSP Controller” was published in IJMRAE journal Vol.6 No II April 2014.
 A paper entitled “Field Oriented Control of Induction Motor Drive Based on TMS320F28035
DSP Controller” was presented in national conference at New Horizon College of Engineering,
Bangalore.
 Participated in a workshop organized by Cranes Software International Limited titled “TI
C2000” during my 2nd
sem M.tech.
 Participated in a workshop organized by Cranes Software International Limited titled “TI
MSP430” during my 1st
sem M.tech.
 Participated in a workshop organized by BSNL titled “Internet and Mobile Communication”
during my 7th
sem B.E.
Personal Details:
Father's Name : Chandra C A
Mother's Name : Manjula
Date of Birth : 31st
Oct 1990
Gender : Male
Marital Status : Single
Languages Known : English, Hindi, Kannada
Declaration
I hereby do declare that the above mentioned information is true to the best of my knowledge
and I bear the responsibility for the correctness of the above mentioned particulars.
Place: Bangalore ROHITH KUMAR C
Date: