concrete tech.reading representation
•
0 likes•126 views
The cement sample was tested for fineness, consistency, setting time, soundness, and compressive strength according to standard tests. The fineness, setting time, and soundness tests all met standards, with the cement being finer, setting within acceptable time ranges, and having low soundness. The 7-day and 28-day compressive strengths exceeded the minimum requirements.
Report
Share
Report
Share
Download to read offline
![TESTING OF CEMENT
SAMPLE CODE:
Sr.No. Name of Test Result Remark
1. FINENESS
a] By dry Sieving(%) 2% Cement is more finer
In nature.
b] Specific Surface(cm/gm)
2. CONSISTANCY (%) 30.25% Say as ‘P’
3. SETTING TIME
a] Initial (Minutes) 120 min. More than 30min. So,O.K.
b] Final (Minutes) 407min. Less than 600min. So,O.K.
4. SOUNDNESS
a] (mm). 1 mm Less than 10mm.So,O.K.
b] ( % ). 3.33 %
5. COMPRESSIVE STRENGTH
AFTER:
a] 3 Days ( ) _ _
b] 7 Days ( ) 32.56ˋˋ
Should not be less than
22
ˋˋ
c] 28 days ( ) 44.78
ˋˋ
Should not be less than
30
ˋˋ](https://image.slidesharecdn.com/ct2-150921221056-lva1-app6891/85/concrete-tech-reading-representation-1-320.jpg)
Recommended
concrete tech.reading representation
This document summarizes test results for a cement sample. Fineness testing showed the cement was finer than 2% when dry sieved. Consistency testing resulted in a value of 30.25% designated as 'P'. Initial and final setting times of 120 minutes and 407 minutes respectively were within acceptable limits. Soundness testing showed 1mm of expansion which was less than the 10mm limit and a 3.33% value for percentage soundness. Compressive strength values at 7 days and 28 days of 32.56 N/mm2 and 44.78 N/mm2 exceeded the minimum requirements of 22 N/mm2 and 30 N/mm2.
Dinta ppt
This document summarizes a study on the effect of adding coir fibre dust as a filler on the mechanical properties of natural rubber vulcanizates. The study found that tensile strength, tear strength, and hardness increased with higher concentrations of coir fibre dust up to 30 parts per hundred rubber (phr), above which the properties declined. Density was also found to increase with higher fibre loading. The study concluded that 30 phr coir fibre dust provided the optimal reinforcement of the natural rubber composites.
Tribological response of fresh and used engine oils 1
PPT of Journal
TRIBOLOGICAL RESPONSE OF FRESH AND USED ENGINE OILS:
THE EFFECT OF SURFACE TEXTURING, ROUGHNESS AND FUEL TYPE.
estimation of structure
This document provides details to estimate quantities for special structures including a soak pit, septic tank, and canal fall. For the soak pit, it calculates the quantities of earthwork, dry brick masonry, brick bat filling, and RCC cover. For the septic tank, it determines the excavation quantity, cement concrete flooring, brick masonry walls, and RCC slab. For the canal fall, it finds the quantities of excavation for the weir wall and guard wall, C.C. for the weir and guard walls, and block/C.R. masonry quantities. Formulas and step-by-step workings are shown to derive the quantities of various items.
concrete tech.reading representation
This document provides test results for aggregates to be used in a concrete mix with a target strength of M30. It includes descriptions and properties of the coarse and fine aggregates such as their source materials, particle shapes, sizes and distributions, densities, water absorption, silt content, specific gravities, and other information needed to design the concrete mix.
READING NOTEDOWN MANUAL CONCRETE TECHNOLOGY
This document provides the recommended mix proportions for concrete with a specified compressive strength of 30 MPa. The mix achieved a compressive strength of 38.25 MPa with a water-cement ratio of 0.42. The mix proportions were 1 part cement, 1.322 parts fine aggregate, 2.342 parts coarse aggregate, and 0.523 parts water by weight. The fresh concrete had a slump of 111 mm and compaction factor of 0.915.
Geology field visit report photos
The document discusses the geological formation process of columnar joints, where water percolates through the pores of cooling lava, forming hexagonal pillars as the rock contracts. Water seeps through the pores and vesicles of the lava, allowing quartz to fill the spaces between hexagonal pillars of columnar joints.
Recommended
concrete tech.reading representation
This document summarizes test results for a cement sample. Fineness testing showed the cement was finer than 2% when dry sieved. Consistency testing resulted in a value of 30.25% designated as 'P'. Initial and final setting times of 120 minutes and 407 minutes respectively were within acceptable limits. Soundness testing showed 1mm of expansion which was less than the 10mm limit and a 3.33% value for percentage soundness. Compressive strength values at 7 days and 28 days of 32.56 N/mm2 and 44.78 N/mm2 exceeded the minimum requirements of 22 N/mm2 and 30 N/mm2.
Dinta ppt
This document summarizes a study on the effect of adding coir fibre dust as a filler on the mechanical properties of natural rubber vulcanizates. The study found that tensile strength, tear strength, and hardness increased with higher concentrations of coir fibre dust up to 30 parts per hundred rubber (phr), above which the properties declined. Density was also found to increase with higher fibre loading. The study concluded that 30 phr coir fibre dust provided the optimal reinforcement of the natural rubber composites.
Tribological response of fresh and used engine oils 1
PPT of Journal
TRIBOLOGICAL RESPONSE OF FRESH AND USED ENGINE OILS:
THE EFFECT OF SURFACE TEXTURING, ROUGHNESS AND FUEL TYPE.
estimation of structure
This document provides details to estimate quantities for special structures including a soak pit, septic tank, and canal fall. For the soak pit, it calculates the quantities of earthwork, dry brick masonry, brick bat filling, and RCC cover. For the septic tank, it determines the excavation quantity, cement concrete flooring, brick masonry walls, and RCC slab. For the canal fall, it finds the quantities of excavation for the weir wall and guard wall, C.C. for the weir and guard walls, and block/C.R. masonry quantities. Formulas and step-by-step workings are shown to derive the quantities of various items.
concrete tech.reading representation
This document provides test results for aggregates to be used in a concrete mix with a target strength of M30. It includes descriptions and properties of the coarse and fine aggregates such as their source materials, particle shapes, sizes and distributions, densities, water absorption, silt content, specific gravities, and other information needed to design the concrete mix.
READING NOTEDOWN MANUAL CONCRETE TECHNOLOGY
This document provides the recommended mix proportions for concrete with a specified compressive strength of 30 MPa. The mix achieved a compressive strength of 38.25 MPa with a water-cement ratio of 0.42. The mix proportions were 1 part cement, 1.322 parts fine aggregate, 2.342 parts coarse aggregate, and 0.523 parts water by weight. The fresh concrete had a slump of 111 mm and compaction factor of 0.915.
Geology field visit report photos
The document discusses the geological formation process of columnar joints, where water percolates through the pores of cooling lava, forming hexagonal pillars as the rock contracts. Water seeps through the pores and vesicles of the lava, allowing quartz to fill the spaces between hexagonal pillars of columnar joints.
concrete tech.reading representation
This document provides the recommended mix proportions for concrete with a target strength of M30 according to IS 10262-2009 standards. The mix achieved a compressive strength of 38.25 MPa at 7 days, which exceeds the specified 30 MPa strength. The mix has a water-cement ratio of 0.42, with a cement content of 456 kg/m3. The mix proportions are 1 part cement to 1.322 parts fine aggregate to 2.342 parts coarse aggregate to 0.523 parts water by weight.
concrete tech.reading representation
This document provides the recommended mix proportions for concrete with a specified compressive strength of 30 MPa. The mix achieved a compressive strength of 38.25 MPa with a water-cement ratio of 0.42. The mix proportions were 1 part cement, 1.322 parts fine aggregate, 2.342 parts coarse aggregate, and 0.523 parts water by weight. The fresh concrete had a slump of 111 mm and compaction factor of 0.915.
Geology field visit report
The document summarizes a geology tour that took place on 23/08/2014. It lists locations visited - Ramling and Dharashiv Leni Caves in Osmanabad. It notes the faculty accompanying the trip - Dr. P.D. Mali, Prof. S.B. Gosavi, and Miss. Pallavi Machcha. It provides details of the student - Basavaraj Vittal Pachapur of S.E. Civil class, Roll No. 4040. The document certifies that the student satisfactorily completed the tour report in Engineering Geology for the 2014-2015 academic year.
Geology field visit report
The geology study tour arranged by Dr. P.D. Mali and Mrs. Machcha of the geology faculty took approximately 70 SE-Civil students to Osmanabad Caves and Ramling on August 23rd, 2014. At the sites, the students studied various volcanic rock formations like vesicular structure, amygdaloidal structure, basalt, columnar joints, and zeolitic basalt. Specifically at Osmanabad Caves, the students observed amygdaloidal basalt and zeolitic basalt, which formed when vesicles in basalt were filled with secondary calcite minerals. At Ramling, massive columnar joints, waterfalls, and potholes were seen. The study concluded that amyg
Geology field visit report photos
Columnar joints form in lava flows and volcanic rock as they cool and contract, creating hexagonal pillars. Water percolates through pores in the volcanic rock, which contain quartz vesicles that form during eruption as gas bubbles escape the lava. The vesicles leave behind empty spaces that become pores in the solidified rock.
Performance evaluation of dense bituminous macadam
This document evaluates the performance of dense bituminous macadam mix using a refusal density approach. It summarizes the objectives of determining the optimum bitumen content using polymer modified bitumen and Hugo hammer compaction. It also aims to study mix properties at refusal density and compare Marshall properties using Hugo hammer and standard compaction. The literature review covers limitations of the Marshall design method in not simulating field conditions. The document outlines the aggregate properties, mix design, and laboratory investigations conducted. Test results found the air void content at refusal density to be 3.76% and established 200 blows as the refusal density. Properties varied with compaction effort, establishing the refusal density approach better simulates field conditions compared to the standard Marshall method.
Geology field visit report
Mr. Aditya Phade, a civil engineering student, accompanied by three faculty members - Dr. P.D. Mali, Prof. S.B. Gosavi, and Miss. Pallavi Machchha - visited two places in Osmanabad district for a geology tour: Ramling and Dharashiv Leni caves. The tour report details the student's name, class, roll number, locations visited defined by latitude and longitude, and faculty accompanying the tour during the 2014-2015 academic year.
Disaster management Flood
This document summarizes a paper presentation on disaster management during floods. It discusses:
1) The phases of flood disaster management including preparedness, impact, response, recovery and mitigation.
2) The roles of civil engineers in flood control activities like reservoir construction, river channelization, drainage improvement, and flood water diversion.
3) Current flood management practices and developments in India, including structures like dams, embankments, and drainage improvement works.
ASPHALT AND ASPHALT RECYCLING BY ENGR ONOJA
PRESENTATION ON ASPHALT AND ASPHALT RECYCLING TO NIGERIAN SOCIETY OF ENGINEERS, ENVIRONMENT DIVISION.BY ENGR ANDREW A. ONOJA.
Bituminous mix design
The document discusses bituminous mix design which involves combining aggregates, bitumen, filler materials like cement or GGBS, shredded plastic, and an anti-stripping agent called Bitu-grip. It provides details on the materials used, testing procedures, results of mix designs for different types of mixes like BC, DBM, BM, and MSS. The use of shredded plastic and Bitu-grip can increase bonding between aggregate and bitumen while filler reduces voids and increases strength. GGBS can be used instead of cement, providing cost savings. Use of these additives results in reduced binder and bitumen content.
mix design m25
The document provides the specifications and design steps for a concrete mix with a target compressive strength of 25 MPa. It specifies the materials to be used including cement, fine and coarse aggregates, and their properties. An 8 step process is outlined to determine the mix proportions: (1) target strength calculation, (2) water-cement ratio selection, (3) water content determination, (4) cement content calculation, (5) aggregate volume proportions, (6) mix proportions by volume, (7) adjustments for material properties, and (8) final mix quantities. The resulting mix has a water-cement ratio of 0.467 and proportions of 1:1.5:2.696:0.467
Irc 111-2009 dense graded bituminous mixes
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive functioning. Exercise causes chemical changes in the brain that may help protect against mental illness and improve symptoms.
Bituminous mix design
1) The document describes the process for Marshall stability test and mix design for bituminous concrete. Key steps include selecting aggregates based on strength and gradation, determining aggregate proportions, preparing specimens, and testing stability and flow.
2) Aggregate proportions are determined using an analytical method solving equations for the required gradation. Specimens are compacted and tested for stability (maximum load) and flow (deformation) at varying bitumen contents to determine the optimum mix.
3) Stability and flow values are measured using a Marshall test machine and calculations are done to determine density, voids, and other properties of the mix. The process is repeated to get the optimum bitumen content for the mix design.
Grading of bitumen by SURAJ KUMAR
This document discusses different methods for grading bituminous binders, including penetration grading, viscosity grading, and performance grading. Penetration grading uses the penetration test results at 25°C to specify grades. Viscosity grading specifies grades based on viscosity measurements at 60°C and 135°C. Performance grading assigns grades based on the temperature ranges where the binder is expected to perform satisfactorily against rutting, fatigue cracking, and low-temperature cracking. The document also covers specifications, advantages and disadvantages of each grading method, and definitions and measurement of viscosity and its importance in characterizing bitumen properties.
Dense Bituminous macadam
Dense Bituminous Macadam (DBM) is a binder course used for roads with more number of heavy commercial vehicles and a close-graded premix material having a voids content of 5-10 per cent.
Hot bituminous mix design
Asphalt mixtures are made up of aggregates, binder and air voids. In order to make a economic and satisfactory performing asphalt mixture the quantity of these individual constituent is required. Mixture design is a tool to determine these optimum quantities.
Block 13 Mix design Historical 13
The document discusses the history and methods of hot mix asphalt (HMA) mix designs. It describes the Marshall and Hveem mix design methods, which were developed in the 1930s-1940s to determine the optimal blend of aggregates and asphalt binders. The Marshall method uses compacted cylindrical specimens subjected to impact compaction and stability testing, while the Hveem method employs kneading compaction and a stabilometer to evaluate shear strength. Both aim to achieve sufficient stability, air voids, and workability within the mix. The Superpave gyratory compactor method was later introduced as a improved alternative.
Shotcrete technology
Shortcreting has proved to be the best method for construction of curved surfaces. Domes are now much easier to construct with the advent of shotcrete technology. Tunnel linings are also becoming easy with this technology. Not only are these but there a wide range of applications where this technology has been a leading one. This technical paper includes the concept of shotcrete and how it differs from conventional concrete. It also enumerates the different types of process involved in shotcreting i.e. dry mix process and wet mix process. Advantages of shotcrete and its applications in various fields like tunneling, canals, buildings etc. are specified in detail. This paper presents an overview of shotcreting technology along with its applications.
DEFINITION OF SHOTCRETE:-
Shotcrete is a mortar or high performance concrete conveyed through a hose and pneumatically projected at high velocity onto a backing surface. It is the force of this spraying action that leads to compaction of the concrete or mortar which then forms layers of concrete to the required thickness. Shotcreting has been an acceptable way of placing cementitious material in a variety of applications.
Usually patented polypropylene fibers are included in the shotcrete which increases the cohesive nature of the shotcrete through mechanically binding the cementitious materials together. This mechanism reduces the rebound waste that occurs through the shotcreting process and these fibers also resist plastic shrinkage and cracking through their ability to enhance the early stage tensile strength of concrete.
Shotcrete also gives better surface finishes and reduces surface tearing on non- linear sections. Cementitious material containing the poly propylene fibers resist cycles of freezing and thawing and also reduces the chances of water and chemical penetrations.
一比一原版(CalArts毕业证)加利福尼亚艺术学院毕业证如何办理
CalArts毕业证学历书【微信95270640】CalArts毕业证’圣力嘉学院毕业证《Q微信95270640》办理CalArts毕业证√文凭学历制作{CalArts文凭}购买学历学位证书本科硕士,CalArts毕业证学历学位证【实体公司】办毕业证、成绩单、学历认证、学位证、文凭认证、办留信网认证、（网上可查，实体公司，专业可靠）
(诚招代理)办理国外高校毕业证成绩单文凭学位证,真实使馆公证（留学回国人员证明）真实留信网认证国外学历学位认证雅思代考国外学校代申请名校保录开请假条改GPA改成绩ID卡
1.高仿业务:【本科硕士】毕业证,成绩单（GPA修改）,学历认证（教育部认证）,大学Offer,,ID,留信认证,使馆认证,雅思,语言证书等高仿类证书；
2.认证服务: 学历认证（教育部认证）,大使馆认证（回国人员证明）,留信认证（可查有编号证书）,大学保录取,雅思保分成绩单。
3.技术服务：钢印水印烫金激光防伪凹凸版设计印刷激凸温感光标底纹镭射速度快。
办理加利福尼亚艺术学院加利福尼亚艺术学院毕业证文凭证书流程：
1客户提供办理信息：姓名生日专业学位毕业时间等（如信息不确定可以咨询顾问：我们有专业老师帮你查询）；
2开始安排制作毕业证成绩单电子图；
3毕业证成绩单电子版做好以后发送给您确认；
4毕业证成绩单电子版您确认信息无误之后安排制作成品；
5成品做好拍照或者视频给您确认；
6快递给客户（国内顺丰国外DHLUPS等快读邮寄）
-办理真实使馆公证（即留学回国人员证明）
-办理各国各大学文凭（世界名校一对一专业服务,可全程监控跟踪进度）
-全套服务：毕业证成绩单真实使馆公证真实教育部认证。让您回国发展信心十足！
（详情请加一下 文凭顾问+微信:95270640）欢迎咨询！子小伍玩小伍比山娃小一岁虎头虎脑的很霸气父亲让山娃跟小伍去夏令营听课山娃很高兴夏令营就设在附近一所小学山娃发现那所小学比自己的学校更大更美操场上还铺有塑胶跑道呢里面很多小朋友一班一班的快快乐乐原来城里娃都藏这儿来了怪不得平时见不到他们山娃恍然大悟起来吹拉弹唱琴棋书画山娃都不懂却什么都想学山娃怨自己太笨什么都不会斟酌再三山娃终于选定了学美术当听说每月要交元时父亲犹豫了山娃也说爸算了吧咱学校一学期才转
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Climate change's impact on the planet forced the United Nations and governments to promote green energies and electric transportation. The deployments of photovoltaic (PV) and electric vehicle (EV) systems gained stronger momentum due to their numerous advantages over fossil fuel types. The advantages go beyond sustainability to reach financial support and stability. The work in this paper introduces the hybrid system between PV and EV to support industrial and commercial plants. This paper covers the theoretical framework of the proposed hybrid system including the required equation to complete the cost analysis when PV and EV are present. In addition, the proposed design diagram which sets the priorities and requirements of the system is presented. The proposed approach allows setup to advance their power stability, especially during power outages. The presented information supports researchers and plant owners to complete the necessary analysis while promoting the deployment of clean energy. The result of a case study that represents a dairy milk farmer supports the theoretical works and highlights its advanced benefits to existing plants. The short return on investment of the proposed approach supports the paper's novelty approach for the sustainable electrical system. In addition, the proposed system allows for an isolated power setup without the need for a transmission line which enhances the safety of the electrical network
More Related Content
Viewers also liked
concrete tech.reading representation
This document provides the recommended mix proportions for concrete with a target strength of M30 according to IS 10262-2009 standards. The mix achieved a compressive strength of 38.25 MPa at 7 days, which exceeds the specified 30 MPa strength. The mix has a water-cement ratio of 0.42, with a cement content of 456 kg/m3. The mix proportions are 1 part cement to 1.322 parts fine aggregate to 2.342 parts coarse aggregate to 0.523 parts water by weight.
concrete tech.reading representation
This document provides the recommended mix proportions for concrete with a specified compressive strength of 30 MPa. The mix achieved a compressive strength of 38.25 MPa with a water-cement ratio of 0.42. The mix proportions were 1 part cement, 1.322 parts fine aggregate, 2.342 parts coarse aggregate, and 0.523 parts water by weight. The fresh concrete had a slump of 111 mm and compaction factor of 0.915.
Geology field visit report
The document summarizes a geology tour that took place on 23/08/2014. It lists locations visited - Ramling and Dharashiv Leni Caves in Osmanabad. It notes the faculty accompanying the trip - Dr. P.D. Mali, Prof. S.B. Gosavi, and Miss. Pallavi Machcha. It provides details of the student - Basavaraj Vittal Pachapur of S.E. Civil class, Roll No. 4040. The document certifies that the student satisfactorily completed the tour report in Engineering Geology for the 2014-2015 academic year.
Geology field visit report
The geology study tour arranged by Dr. P.D. Mali and Mrs. Machcha of the geology faculty took approximately 70 SE-Civil students to Osmanabad Caves and Ramling on August 23rd, 2014. At the sites, the students studied various volcanic rock formations like vesicular structure, amygdaloidal structure, basalt, columnar joints, and zeolitic basalt. Specifically at Osmanabad Caves, the students observed amygdaloidal basalt and zeolitic basalt, which formed when vesicles in basalt were filled with secondary calcite minerals. At Ramling, massive columnar joints, waterfalls, and potholes were seen. The study concluded that amyg
Geology field visit report photos
Columnar joints form in lava flows and volcanic rock as they cool and contract, creating hexagonal pillars. Water percolates through pores in the volcanic rock, which contain quartz vesicles that form during eruption as gas bubbles escape the lava. The vesicles leave behind empty spaces that become pores in the solidified rock.
Performance evaluation of dense bituminous macadam
This document evaluates the performance of dense bituminous macadam mix using a refusal density approach. It summarizes the objectives of determining the optimum bitumen content using polymer modified bitumen and Hugo hammer compaction. It also aims to study mix properties at refusal density and compare Marshall properties using Hugo hammer and standard compaction. The literature review covers limitations of the Marshall design method in not simulating field conditions. The document outlines the aggregate properties, mix design, and laboratory investigations conducted. Test results found the air void content at refusal density to be 3.76% and established 200 blows as the refusal density. Properties varied with compaction effort, establishing the refusal density approach better simulates field conditions compared to the standard Marshall method.
Geology field visit report
Mr. Aditya Phade, a civil engineering student, accompanied by three faculty members - Dr. P.D. Mali, Prof. S.B. Gosavi, and Miss. Pallavi Machchha - visited two places in Osmanabad district for a geology tour: Ramling and Dharashiv Leni caves. The tour report details the student's name, class, roll number, locations visited defined by latitude and longitude, and faculty accompanying the tour during the 2014-2015 academic year.
Disaster management Flood
This document summarizes a paper presentation on disaster management during floods. It discusses:
1) The phases of flood disaster management including preparedness, impact, response, recovery and mitigation.
2) The roles of civil engineers in flood control activities like reservoir construction, river channelization, drainage improvement, and flood water diversion.
3) Current flood management practices and developments in India, including structures like dams, embankments, and drainage improvement works.
ASPHALT AND ASPHALT RECYCLING BY ENGR ONOJA
PRESENTATION ON ASPHALT AND ASPHALT RECYCLING TO NIGERIAN SOCIETY OF ENGINEERS, ENVIRONMENT DIVISION.BY ENGR ANDREW A. ONOJA.
Bituminous mix design
The document discusses bituminous mix design which involves combining aggregates, bitumen, filler materials like cement or GGBS, shredded plastic, and an anti-stripping agent called Bitu-grip. It provides details on the materials used, testing procedures, results of mix designs for different types of mixes like BC, DBM, BM, and MSS. The use of shredded plastic and Bitu-grip can increase bonding between aggregate and bitumen while filler reduces voids and increases strength. GGBS can be used instead of cement, providing cost savings. Use of these additives results in reduced binder and bitumen content.
mix design m25
The document provides the specifications and design steps for a concrete mix with a target compressive strength of 25 MPa. It specifies the materials to be used including cement, fine and coarse aggregates, and their properties. An 8 step process is outlined to determine the mix proportions: (1) target strength calculation, (2) water-cement ratio selection, (3) water content determination, (4) cement content calculation, (5) aggregate volume proportions, (6) mix proportions by volume, (7) adjustments for material properties, and (8) final mix quantities. The resulting mix has a water-cement ratio of 0.467 and proportions of 1:1.5:2.696:0.467
Irc 111-2009 dense graded bituminous mixes
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive functioning. Exercise causes chemical changes in the brain that may help protect against mental illness and improve symptoms.
Bituminous mix design
1) The document describes the process for Marshall stability test and mix design for bituminous concrete. Key steps include selecting aggregates based on strength and gradation, determining aggregate proportions, preparing specimens, and testing stability and flow.
2) Aggregate proportions are determined using an analytical method solving equations for the required gradation. Specimens are compacted and tested for stability (maximum load) and flow (deformation) at varying bitumen contents to determine the optimum mix.
3) Stability and flow values are measured using a Marshall test machine and calculations are done to determine density, voids, and other properties of the mix. The process is repeated to get the optimum bitumen content for the mix design.
Grading of bitumen by SURAJ KUMAR
This document discusses different methods for grading bituminous binders, including penetration grading, viscosity grading, and performance grading. Penetration grading uses the penetration test results at 25°C to specify grades. Viscosity grading specifies grades based on viscosity measurements at 60°C and 135°C. Performance grading assigns grades based on the temperature ranges where the binder is expected to perform satisfactorily against rutting, fatigue cracking, and low-temperature cracking. The document also covers specifications, advantages and disadvantages of each grading method, and definitions and measurement of viscosity and its importance in characterizing bitumen properties.
Dense Bituminous macadam
Dense Bituminous Macadam (DBM) is a binder course used for roads with more number of heavy commercial vehicles and a close-graded premix material having a voids content of 5-10 per cent.
Hot bituminous mix design
Asphalt mixtures are made up of aggregates, binder and air voids. In order to make a economic and satisfactory performing asphalt mixture the quantity of these individual constituent is required. Mixture design is a tool to determine these optimum quantities.
Block 13 Mix design Historical 13
The document discusses the history and methods of hot mix asphalt (HMA) mix designs. It describes the Marshall and Hveem mix design methods, which were developed in the 1930s-1940s to determine the optimal blend of aggregates and asphalt binders. The Marshall method uses compacted cylindrical specimens subjected to impact compaction and stability testing, while the Hveem method employs kneading compaction and a stabilometer to evaluate shear strength. Both aim to achieve sufficient stability, air voids, and workability within the mix. The Superpave gyratory compactor method was later introduced as a improved alternative.
Shotcrete technology
Shortcreting has proved to be the best method for construction of curved surfaces. Domes are now much easier to construct with the advent of shotcrete technology. Tunnel linings are also becoming easy with this technology. Not only are these but there a wide range of applications where this technology has been a leading one. This technical paper includes the concept of shotcrete and how it differs from conventional concrete. It also enumerates the different types of process involved in shotcreting i.e. dry mix process and wet mix process. Advantages of shotcrete and its applications in various fields like tunneling, canals, buildings etc. are specified in detail. This paper presents an overview of shotcreting technology along with its applications.
DEFINITION OF SHOTCRETE:-
Shotcrete is a mortar or high performance concrete conveyed through a hose and pneumatically projected at high velocity onto a backing surface. It is the force of this spraying action that leads to compaction of the concrete or mortar which then forms layers of concrete to the required thickness. Shotcreting has been an acceptable way of placing cementitious material in a variety of applications.
Usually patented polypropylene fibers are included in the shotcrete which increases the cohesive nature of the shotcrete through mechanically binding the cementitious materials together. This mechanism reduces the rebound waste that occurs through the shotcreting process and these fibers also resist plastic shrinkage and cracking through their ability to enhance the early stage tensile strength of concrete.
Shotcrete also gives better surface finishes and reduces surface tearing on non- linear sections. Cementitious material containing the poly propylene fibers resist cycles of freezing and thawing and also reduces the chances of water and chemical penetrations.
Viewers also liked (20)
Performance evaluation of dense bituminous macadam
Performance evaluation of dense bituminous macadam
Recently uploaded
一比一原版(CalArts毕业证)加利福尼亚艺术学院毕业证如何办理
CalArts毕业证学历书【微信95270640】CalArts毕业证’圣力嘉学院毕业证《Q微信95270640》办理CalArts毕业证√文凭学历制作{CalArts文凭}购买学历学位证书本科硕士,CalArts毕业证学历学位证【实体公司】办毕业证、成绩单、学历认证、学位证、文凭认证、办留信网认证、（网上可查，实体公司，专业可靠）
(诚招代理)办理国外高校毕业证成绩单文凭学位证,真实使馆公证（留学回国人员证明）真实留信网认证国外学历学位认证雅思代考国外学校代申请名校保录开请假条改GPA改成绩ID卡
1.高仿业务:【本科硕士】毕业证,成绩单（GPA修改）,学历认证（教育部认证）,大学Offer,,ID,留信认证,使馆认证,雅思,语言证书等高仿类证书；
2.认证服务: 学历认证（教育部认证）,大使馆认证（回国人员证明）,留信认证（可查有编号证书）,大学保录取,雅思保分成绩单。
3.技术服务：钢印水印烫金激光防伪凹凸版设计印刷激凸温感光标底纹镭射速度快。
办理加利福尼亚艺术学院加利福尼亚艺术学院毕业证文凭证书流程：
1客户提供办理信息：姓名生日专业学位毕业时间等（如信息不确定可以咨询顾问：我们有专业老师帮你查询）；
2开始安排制作毕业证成绩单电子图；
3毕业证成绩单电子版做好以后发送给您确认；
4毕业证成绩单电子版您确认信息无误之后安排制作成品；
5成品做好拍照或者视频给您确认；
6快递给客户（国内顺丰国外DHLUPS等快读邮寄）
-办理真实使馆公证（即留学回国人员证明）
-办理各国各大学文凭（世界名校一对一专业服务,可全程监控跟踪进度）
-全套服务：毕业证成绩单真实使馆公证真实教育部认证。让您回国发展信心十足！
（详情请加一下 文凭顾问+微信:95270640）欢迎咨询！子小伍玩小伍比山娃小一岁虎头虎脑的很霸气父亲让山娃跟小伍去夏令营听课山娃很高兴夏令营就设在附近一所小学山娃发现那所小学比自己的学校更大更美操场上还铺有塑胶跑道呢里面很多小朋友一班一班的快快乐乐原来城里娃都藏这儿来了怪不得平时见不到他们山娃恍然大悟起来吹拉弹唱琴棋书画山娃都不懂却什么都想学山娃怨自己太笨什么都不会斟酌再三山娃终于选定了学美术当听说每月要交元时父亲犹豫了山娃也说爸算了吧咱学校一学期才转
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Climate change's impact on the planet forced the United Nations and governments to promote green energies and electric transportation. The deployments of photovoltaic (PV) and electric vehicle (EV) systems gained stronger momentum due to their numerous advantages over fossil fuel types. The advantages go beyond sustainability to reach financial support and stability. The work in this paper introduces the hybrid system between PV and EV to support industrial and commercial plants. This paper covers the theoretical framework of the proposed hybrid system including the required equation to complete the cost analysis when PV and EV are present. In addition, the proposed design diagram which sets the priorities and requirements of the system is presented. The proposed approach allows setup to advance their power stability, especially during power outages. The presented information supports researchers and plant owners to complete the necessary analysis while promoting the deployment of clean energy. The result of a case study that represents a dairy milk farmer supports the theoretical works and highlights its advanced benefits to existing plants. The short return on investment of the proposed approach supports the paper's novelty approach for the sustainable electrical system. In addition, the proposed system allows for an isolated power setup without the need for a transmission line which enhances the safety of the electrical network
BRAIN TUMOR DETECTION for seminar ppt.pdf
BRAIN TUMOR DETECTION
AND CLASSIFICATION USING
ARTIFICIAL INTELLIGENCE
Use PyCharm for remote debugging of WSL on a Windo cf5c162d672e4e58b4dde5d797...
This document serves as a comprehensive step-by-step guide on how to effectively use PyCharm for remote debugging of the Windows Subsystem for Linux (WSL) on a local Windows machine. It meticulously outlines several critical steps in the process, starting with the crucial task of enabling permissions, followed by the installation and configuration of WSL.
The guide then proceeds to explain how to set up the SSH service within the WSL environment, an integral part of the process. Alongside this, it also provides detailed instructions on how to modify the inbound rules of the Windows firewall to facilitate the process, ensuring that there are no connectivity issues that could potentially hinder the debugging process.
The document further emphasizes on the importance of checking the connection between the Windows and WSL environments, providing instructions on how to ensure that the connection is optimal and ready for remote debugging.
It also offers an in-depth guide on how to configure the WSL interpreter and files within the PyCharm environment. This is essential for ensuring that the debugging process is set up correctly and that the program can be run effectively within the WSL terminal.
Additionally, the document provides guidance on how to set up breakpoints for debugging, a fundamental aspect of the debugging process which allows the developer to stop the execution of their code at certain points and inspect their program at those stages.
Finally, the document concludes by providing a link to a reference blog. This blog offers additional information and guidance on configuring the remote Python interpreter in PyCharm, providing the reader with a well-rounded understanding of the process.
Software Engineering and Project Management - Introduction, Modeling Concepts...
Introduction, Modeling Concepts and Class Modeling: What is Object orientation? What is OO development? OO Themes; Evidence for usefulness of OO development; OO modeling history. Modeling
as Design technique: Modeling, abstraction, The Three models. Class Modeling: Object and Class Concept, Link and associations concepts, Generalization and Inheritance, A sample class model, Navigation of class models, and UML diagrams
Building the Analysis Models: Requirement Analysis, Analysis Model Approaches, Data modeling Concepts, Object Oriented Analysis, Scenario-Based Modeling, Flow-Oriented Modeling, class Based Modeling, Creating a Behavioral Model.
官方认证美国密歇根州立大学毕业证学位证书原版一模一样
原版一模一样【微信：741003700 】【美国密歇根州立大学毕业证学位证书】【微信：741003700 】学位证，留信认证（真实可查，永久存档）offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原海外各大学 Bachelor Diploma degree, Master Degree Diploma
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
22CYT12-Unit-V-E Waste and its Management.ppt
Introduction- e - waste – definition - sources of e-waste– hazardous substances in e-waste - effects of e-waste on environment and human health- need for e-waste management– e-waste handling rules - waste minimization techniques for managing e-waste – recycling of e-waste - disposal treatment methods of e- waste – mechanism of extraction of precious metal from leaching solution-global Scenario of E-waste – E-waste in India- case studies.
AI assisted telemedicine KIOSK for Rural India.pptx
It gives the overall description of SIH problem statement " AI assisted telemedicine KIOSK for Rural India".
An improved modulation technique suitable for a three level flying capacitor ...
This research paper introduces an innovative modulation technique for controlling a 3-level flying capacitor multilevel inverter (FCMLI), aiming to streamline the modulation process in contrast to conventional methods. The proposed
simplified modulation technique paves the way for more straightforward and
efficient control of multilevel inverters, enabling their widespread adoption and
integration into modern power electronic systems. Through the amalgamation of
sinusoidal pulse width modulation (SPWM) with a high-frequency square wave
pulse, this controlling technique attains energy equilibrium across the coupling
capacitor. The modulation scheme incorporates a simplified switching pattern
and a decreased count of voltage references, thereby simplifying the control
algorithm.
Rainfall intensity duration frequency curve statistical analysis and modeling...
Using data from 41 years in Patna’ India’ the study’s goal is to analyze the trends of how often it rains on a weekly, seasonal, and annual basis (1981−2020). First, utilizing the intensity-duration-frequency (IDF) curve and the relationship by statistically analyzing rainfall’ the historical rainfall data set for Patna’ India’ during a 41 year period (1981−2020), was evaluated for its quality. Changes in the hydrologic cycle as a result of increased greenhouse gas emissions are expected to induce variations in the intensity, length, and frequency of precipitation events. One strategy to lessen vulnerability is to quantify probable changes and adapt to them. Techniques such as log-normal, normal, and Gumbel are used (EV-I). Distributions were created with durations of 1, 2, 3, 6, and 24 h and return times of 2, 5, 10, 25, and 100 years. There were also mathematical correlations discovered between rainfall and recurrence interval.
Findings: Based on findings, the Gumbel approach produced the highest intensity values, whereas the other approaches produced values that were close to each other. The data indicates that 461.9 mm of rain fell during the monsoon season’s 301st week. However, it was found that the 29th week had the greatest average rainfall, 92.6 mm. With 952.6 mm on average, the monsoon season saw the highest rainfall. Calculations revealed that the yearly rainfall averaged 1171.1 mm. Using Weibull’s method, the study was subsequently expanded to examine rainfall distribution at different recurrence intervals of 2, 5, 10, and 25 years. Rainfall and recurrence interval mathematical correlations were also developed. Further regression analysis revealed that short wave irrigation, wind direction, wind speed, pressure, relative humidity, and temperature all had a substantial influence on rainfall.
Originality and value: The results of the rainfall IDF curves can provide useful information to policymakers in making appropriate decisions in managing and minimizing floods in the study area.
Null Bangalore | Pentesters Approach to AWS IAM
#Abstract:
- Learn more about the real-world methods for auditing AWS IAM (Identity and Access Management) as a pentester. So let us proceed with a brief discussion of IAM as well as some typical misconfigurations and their potential exploits in order to reinforce the understanding of IAM security best practices.
- Gain actionable insights into AWS IAM policies and roles, using hands on approach.
#Prerequisites:
- Basic understanding of AWS services and architecture
- Familiarity with cloud security concepts
- Experience using the AWS Management Console or AWS CLI.
- For hands on lab create account on [killercoda.com](https://killercoda.com/cloudsecurity-scenario/)
# Scenario Covered:
- Basics of IAM in AWS
- Implementing IAM Policies with Least Privilege to Manage S3 Bucket
- Objective: Create an S3 bucket with least privilege IAM policy and validate access.
- Steps:
- Create S3 bucket.
- Attach least privilege policy to IAM user.
- Validate access.
- Exploiting IAM PassRole Misconfiguration
-Allows a user to pass a specific IAM role to an AWS service (ec2), typically used for service access delegation. Then exploit PassRole Misconfiguration granting unauthorized access to sensitive resources.
- Objective: Demonstrate how a PassRole misconfiguration can grant unauthorized access.
- Steps:
- Allow user to pass IAM role to EC2.
- Exploit misconfiguration for unauthorized access.
- Access sensitive resources.
- Exploiting IAM AssumeRole Misconfiguration with Overly Permissive Role
- An overly permissive IAM role configuration can lead to privilege escalation by creating a role with administrative privileges and allow a user to assume this role.
- Objective: Show how overly permissive IAM roles can lead to privilege escalation.
- Steps:
- Create role with administrative privileges.
- Allow user to assume the role.
- Perform administrative actions.
- Differentiation between PassRole vs AssumeRole
Try at [killercoda.com](https://killercoda.com/cloudsecurity-scenario/)
Advanced control scheme of doubly fed induction generator for wind turbine us...
This paper describes a speed control device for generating electrical energy on an electricity network based on the doubly fed induction generator (DFIG) used for wind power conversion systems. At first, a double-fed induction generator model was constructed. A control law is formulated to govern the flow of energy between the stator of a DFIG and the energy network using three types of controllers: proportional integral (PI), sliding mode controller (SMC) and second order sliding mode controller (SOSMC). Their different results in terms of power reference tracking, reaction to unexpected speed fluctuations, sensitivity to perturbations, and resilience against machine parameter alterations are compared. MATLAB/Simulink was used to conduct the simulations for the preceding study. Multiple simulations have shown very satisfying results, and the investigations demonstrate the efficacy and power-enhancing capabilities of the suggested control system.
Comparative analysis between traditional aquaponics and reconstructed aquapon...
The aquaponic system of planting is a method that does not require soil usage. It is a method that only needs water, fish, lava rocks (a substitute for soil), and plants. Aquaponic systems are sustainable and environmentally friendly. Its use not only helps to plant in small spaces but also helps reduce artificial chemical use and minimizes excess water use, as aquaponics consumes 90% less water than soil-based gardening. The study applied a descriptive and experimental design to assess and compare conventional and reconstructed aquaponic methods for reproducing tomatoes. The researchers created an observation checklist to determine the significant factors of the study. The study aims to determine the significant difference between traditional aquaponics and reconstructed aquaponics systems propagating tomatoes in terms of height, weight, girth, and number of fruits. The reconstructed aquaponics system’s higher growth yield results in a much more nourished crop than the traditional aquaponics system. It is superior in its number of fruits, height, weight, and girth measurement. Moreover, the reconstructed aquaponics system is proven to eliminate all the hindrances present in the traditional aquaponics system, which are overcrowding of fish, algae growth, pest problems, contaminated water, and dead fish.
Mechanical Engineering on AAI Summer Training Report-003.pdf
Mechanical Engineering PROJECT REPORT ON SUMMER VOCATIONAL TRAINING
AT MBB AIRPORT
Data Driven Maintenance | UReason Webinar
Discover the latest insights on Data Driven Maintenance with our comprehensive webinar presentation. Learn about traditional maintenance challenges, the right approach to utilizing data, and the benefits of adopting a Data Driven Maintenance strategy. Explore real-world examples, industry best practices, and innovative solutions like FMECA and the D3M model. This presentation, led by expert Jules Oudmans, is essential for asset owners looking to optimize their maintenance processes and leverage digital technologies for improved efficiency and performance. Download now to stay ahead in the evolving maintenance landscape.
Recently uploaded (20)
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Use PyCharm for remote debugging of WSL on a Windo cf5c162d672e4e58b4dde5d797...
Use PyCharm for remote debugging of WSL on a Windo cf5c162d672e4e58b4dde5d797...
Software Engineering and Project Management - Introduction, Modeling Concepts...
Software Engineering and Project Management - Introduction, Modeling Concepts...
AI assisted telemedicine KIOSK for Rural India.pptx
AI assisted telemedicine KIOSK for Rural India.pptx
An improved modulation technique suitable for a three level flying capacitor ...
An improved modulation technique suitable for a three level flying capacitor ...
Rainfall intensity duration frequency curve statistical analysis and modeling...
Rainfall intensity duration frequency curve statistical analysis and modeling...
Advanced control scheme of doubly fed induction generator for wind turbine us...
Advanced control scheme of doubly fed induction generator for wind turbine us...
Generative AI leverages algorithms to create various forms of content
Generative AI leverages algorithms to create various forms of content
Comparative analysis between traditional aquaponics and reconstructed aquapon...
Comparative analysis between traditional aquaponics and reconstructed aquapon...
Mechanical Engineering on AAI Summer Training Report-003.pdf
Mechanical Engineering on AAI Summer Training Report-003.pdf
4. Mosca vol I -Fisica-Tipler-5ta-Edicion-Vol-1.pdf
4. Mosca vol I -Fisica-Tipler-5ta-Edicion-Vol-1.pdf
concrete tech.reading representation
- 1. TESTING OF CEMENT SAMPLE CODE: Sr.No. Name of Test Result Remark 1. FINENESS a] By dry Sieving(%) 2% Cement is more finer In nature. b] Specific Surface(cm/gm) 2. CONSISTANCY (%) 30.25% Say as ‘P’ 3. SETTING TIME a] Initial (Minutes) 120 min. More than 30min. So,O.K. b] Final (Minutes) 407min. Less than 600min. So,O.K. 4. SOUNDNESS a] (mm). 1 mm Less than 10mm.So,O.K. b] ( % ). 3.33 % 5. COMPRESSIVE STRENGTH AFTER: a] 3 Days ( ) _ _ b] 7 Days ( ) 32.56ˋˋ Should not be less than 22 ˋˋ c] 28 days ( ) 44.78 ˋˋ Should not be less than 30 ˋˋ