The document contains questions about CATIA V5 modeling, assembly design, and drafting. It asks about topics like the differences between various sketching and modeling tools in CATIA like pads versus extrusions, assembly constraints, and creating associative versus non-associative drawings. Some key questions asked about the differences between things like bodies and parts, assembly constraints like coincident versus fixed, and changing projection styles in drawings. The document covers a wide range of topics across multiple disciplines in CATIA V5.

1. PARAG D
CATIA V5
Sketcher:
1.What is the difference between position sketch and sliding sketch?
2.How the changes sketch support and how to isolate sketch support?
3.Is it possible to give fillet to two parallel lines? If possible how?
4.How many constrains are required to arrest the degrees of freedom of a point and ellipse on a
plane?
5.How to edit the grid spacing in sketcher?
6.What is in consistence element?
7.How to check the status of a sketch?
8.Different color diagnostics?
9.How to draw inscribed hexagon and circumference hexagon?
10.What the difference connecting options are in connect option?
11.What happen if we increase the tension in connect option?
12.What is iso-constrain?
13.What is the difference between geometric constrain and dimensional constrain?
14.What is the difference between trim and break?
15.Explain the function of 3D geometry?
16.Difference between symmetry and mirror?
17.Different propagation modes in offset command?
18.How to give fillets to corners of rectangle at a time?
19.How to change a line into an axis line?
20.Is it possible to draw two axis lines in a sketch?
21.What is Intersect 3D element?
22.What is swap in dimensioning in sketcher?
23.How to give the angle between ellipse major axis and to a line?
24.What are the difference ways to enter in the sketch work bench?
25.What are the different ways to exit from the sketcher work bench?
Part:
1.What is the result if 5 concentric circles are padded?
2.What is the difference between limit and offset in the pad command?
3.Which type of profiles is not possible to extrude in pad command?
4.How many directions a sketch can be extruded?
5.Explain the possible results if an open profile is padded in a thin rectangular block?
6.When the merge ends options will available?
7.How material will be added to the supports from an open profile in merge ends option?
8.What is neutral fiber?
9.What is the length of the pad if extended a pad with X length by using mirror extend option?
10.What is the difference between up to surface and up to plane in limit types in pad?
11.What is drafted filleted pad?
12.If a sketch contain 5 different boundaries? Explain different possible ways to extrude the sketch?
14.In how may direction a sketch be able to be extruded?
15.Is it possible to extrude a surface?
16.Is it possible to create pocket as a first feature? Why?
17.Is it possible to place a hole on a cylindrical surface?
18.How to change a hole placement support?
19.What is the difference between Merge ends and merge rib ends?
20.What are the different profile control types in rib option?
21.What is keep angle in rib option?
22.What is the pulling direction in the keep angle option?
23.What is the pulling direction?
23.What is the difference between rib and slot?
24.What is difference between from side and from top in stiffener option?

2. PARAG D
25.What is solid combine?
26.What is the difference between rib and multi section solid?
27.How to measure the angle between a curve and line?
28.What are the different coupling modes in multi section solid option?
29.What is the difference between guide curve and spline?
30.What is coupling curve?
31.What is the ration coupling mode in multi section solid?
32.How an end profile will be oriented to the spine if we use re-limitation option?
33.What is the function of closing point and tangent direction?
34.What is the use of smoothing parameters?
35.What is a fillet? And what is the use fillet?
36.Explain the function of edges to keep?
37.Explain the function of trim ribbons?
38.What are the different variations in the variable radius fillet?
39.What is blend corner?
40.What is circle fillet?
41.What is blend corner?
42.Why it is not possible give the face to face fillets to two vertical faces?
43.What is tri-tangent fillet?
44.What is the difference between parting element, limiting element and neutral element?
45.What is pulling direction?
46.How to give multiple neutral elements?
47.When to use draft reflect line?
48.What is the difference between thread and tap?
49.What is the difference between remove face and replace face?
50.What is the difference between Euclidian and geodesic?
51.Is it possible to create a new plane angular to XY pane about X-axis?
52.What is the function project rotation axis on the reference plane?
53.How many points are required to create a plane?
54.Is it possible to create a new plane normal to the screen?
55.What is the function of compass?
56.What is the difference between move and pan?
57.How to move a component in the space by using compass?
58.Is it possible to move a part with 3D constrain?
59.What are the different patterns available in pattern option?
60.What is keep specification in pattern?
61.What is simplified representation?
62.Is it possible to pattern a fillet? If possible how?
63.Is it possible to explode a sketch? If possible what happen to sketch support?
64.How to form a pattern along a curve?
65.What is anchoring point?
66.Is it possible to give a point as a reference in the scaling?
67.What is hybrid design?
68.What is a body?
69.What is the difference between geometrical set and ordered geometrical set?
70.Is it possible to insert a body in ordered geometrical set?
71.What is the difference between body and part?
72.If a part contains 5 bodies if I use the shell…which body will effect due to shell command?
73.What is negative body?
74.What is a Boolean operation?
75.Is it possible to insert body in a body?
76.What the difference is between assemble and add?
77.What is the use of remove lump?
78.What is the resultant body if a negative body is removing from a negative body?

3. PARAG D
79.Is it possible to delete a Boolean operation?
80.Is it possible to delete part body?
81.How to change body into a part body?
82.Is it possible to change adding operation into remove?
83.Is it possible to change assembling into remove?
Generative shape design:
1.What is the difference between line and axis?
2.What is the difference between line and poly line?
3.How a curve will be projected on a surface?
4.What is the function of smoothing in projection?
5.Is it possible to intersect t a line and line which are on different planes?
6.What is the possible resulting element if a surface and a solid intersect?
7.Is it possible to create a circle on a non planar surface?
8.What is the difference between corner on support, 3D corner and corner on vertex?
9.What is the difference between connect types “normal” and “base curve” in connect curve
options?
10.What is the function of tension in connect curve option?
11.What is the difference between close a spline and giving first point as last point?
12.Define curvature?
13.What are the different radius variation methods in the helix option?
14.What is Multi Result Management?
15.Is it possible to extrude a point?
16.What are the sub-elements to remove option?
17.Define passing point?
18.What is canonical portion detection?
19.Explain about blend option?
20.How to know the closing points in blend option when there is open section are used?
21.Define merging distance?
22.What is the max and min merging distance in join operation?
23.What is angular threshold?
24.What is meant by federation?
25.What is the difference between no federation and point propagation?
26.Which types of elements are join in join option?
27.What is the difference between join and healing?
28.Function of untrim?
29.Explain about disassemble?
30.How to make a hole on a spherical surface?
31.Is it possible to trim a multiple elements with a single element?
32.What is the difference between split and trim?
33.Is it possible to use pieces option in trim for surfaces?
34.What is the difference between boundary and extract?
35.What is the difference between scaling and affinity?
36.What is meant by extrapolate?
37.What is the difference between normal extremity and tangent extremity in extrapolate option?
38.What is reflecting line?
39.What is the difference between 3D offset and parallel curve?
40.Define spine?
41.What is the difference between sweep and adaptive sweep?
42.What is the explicit sweep and implicit sweep?
43.What is the anchoring point in sweep option?
44.How to define the depth of the swept surface in sweep operation?
45.Different laws available in seep operation?
46.When we need to go for a law?

4. PARAG D
47.What are the different parameters we can change by using law option ins weep option?
48.Explain three sub-options available in with draft direction option in sweep command?
49.Is it possible to give a curve as center curve to rotate a profile about a curve?
50.What are the different parameter values for different conics?
51.What is the difference between solid and volume in CATIA V5?
Assembly design:
What is the difference between product and a component?
2.What is the function of selective load?
3.How to insert an existing sub-assembly into the assembly?
4.How the function of graph tree re-ordering?
6.What is the fast multi instantiation?
7.What is the difference between moving and constraining?
8.How to constrain the first part in the assembly?
9.What is the difference between mat and coincidence?
10.What is the difference between fix and fix together?
11.How to assembly the components in a pattern?
12.Different assembly features in the assembly work bench?
13.How to check the degrees of freedom of a component in the assembly?
14.How to check the constrains of a component in the assembly?
15.What is the difference between save, save all and save management?
16.Why we have to generate numbers for the components in the assembly?
17.How to re-show the path of a part in the assembly?
18.What the difference is between replace component and replace in session?
19.What is the difference between save, save as, save all, save management?
Drafting:
1.What is associative drawing and non-associative drawing?
2.How to change the standard of a drawing?
3.How to change the angle of projection in the drawing sheet?
4.What is the difference between offset section view and offset section cue?
5.What is the difference between offset section view and aligned section view?
6.What is the difference between detail view and quick detail view?
7.What is the difference between clipping view and detail view?
8.What is the difference between broken view break out view?
9.What is the difference between sheet and detail sheet?
10.Function of Instantiate 2D component?11.What is new view?
12.How to generate stacked dimensions, Cumulative dimensions and chained dimensions?
13.How to break a dimension line?
14.How to create a datum symbol?
15.How to create a composite control frame?
16.How to create a balloon the assembly drawing?
17.How to create a bill of material in the drawing?
18.How to generate a Bill of material in the drawing?
19.How to control the number of columns and column names in the drawing?
20.How to generate a balloon in assembly drawing?
21.How to generate the numbers for the assembly drawing?
22.Which dimensions are generated in the drawing?
23.Which dimensions are editable in drawing?
24.How to generate hole table?
25.How to give the reference for the hole table?
26.Is it possible to place a existing text table in the drawing sheet? How?
27.How to create center lines and thread in the drawing?

5. PARAG D
28.How to hatch an area?
29. How a pattern appears in the drawing if it is in the simplifies representation?
30.How to change the scale factor of a sheet?
31.How to change the angle of projection?
32.How to create a user defied sheet size?
33.How to insert a title block in the sheet?
34.Different ways to insert a title block?
35.How to give the dual value for the dimension?
36.How to give fake dimension?
37.How to change the dimension arrow shape?
38.How to create basic dimension?
39.How to create a circular axis in a drawing?
40.How to link text with dimension?
41.How to align text to the view?
42.How to break the association between views?
43.How to change the dimension text properties?
44.How to display to threads in the drawing?
45.How to measure true length for a iso-metric projection?