This document provides instructions for removing the final drive, steering differential, and brake on the left side of a D6N Track-Type Tractor. The key steps include:
1. Separating the track and removing the steering motor.
2. Attaching lifting brackets and removing mounting bolts to lift off the final drive, steering differential, and brake assembly.
3. Using pullers and forcing screws to remove shafts and gears from the assembly.
The document contains detailed illustrations and instructions for safely and properly disassembling these components using the specified tools.
This document provides instructions for disassembling and assembling the final drive of a D6N LGP track-type tractor. It describes:
1) Removing over 20 components of the final drive including carriers, planetary gears, seals, and sprockets.
2) Cleaning and inspecting removed parts.
3) Reassembling the final drive by installing components in the reverse order of removal while precisely positioning bearings and seals using specialized tools.
This document provides instructions for disassembling and assembling the final drive, steering differential, and brake on the left side of a D6N LGP track-type tractor. It lists the required tools and gives step-by-step details on removing components like the adapter, bolts, sprocket segment, and installing seals and bearings. The purpose is to guide maintenance technicians in properly servicing these systems while ensuring safety around hydraulic pressure.
This document provides instructions for disassembling and assembling the final drive of a D6N LGP track-type tractor. It describes:
1) Removing over 20 components of the final drive including carriers, planetary gears, seals, and sprockets by using various tools like brackets, pullers, and presses.
2) Assembling the components by lowering temperatures, inserting seals, and torquing bolts to specified values using the same tools.
3) Procedures for removing and installing the entire left side final drive, steering differential, and brake assembly, which weighs 680 kg.
The document provides instructions for removing the final drive, steering differential, and brake from the left side of a D6N track-type tractor. It lists the required tools and presents a 20-step procedure involving removing mounting bolts, shafts, gears, seals, and other components. Detailed illustrations accompany each step to show the correct positioning of tools and order of disassembly.
The document provides instructions for removing the final drive, steering differential, and brake from the left side of a D6N track-type tractor. It lists the required tools and presents a 20-step procedure involving removing mounting bolts, shafts, gears, seals, and other components. Detailed illustrations accompany each step to show the correct positioning of tools and order of disassembly.
The document provides instructions for removing the final drive, steering differential, and brake from the left side of a D6N track-type tractor. It lists the required tools and presents a 20-step procedure involving removing mounting bolts, shafts, gears, seals, and other components. Detailed illustrations accompany each step to show the correct positioning of tools and order of disassembly.
This document provides instructions for disassembling and assembling the final drive of a D6N XL track-type tractor. The disassembly process involves removing multiple components of the final drive including the carrier, planetary gears, ring gear, sprocket hub, and seals. The assembly process describes installing these components in reverse order and includes torque specifications for the bolts. Tools required include various brackets, pullers, and presses. Safety precautions are provided regarding the weight of components and hot hydraulic oil.
This document provides instructions for disassembling and assembling the final drive, steering differential, and brake of a D6N XL track-type tractor. The disassembly process involves using various tools to remove 20 bolts and nuts, as well as the carrier, shafts, gears, seals, and sprocket hub. The assembly is the reverse of the disassembly process and requires carefully lowering temperatures, applying lubricant, and tightening bolts to the specified torques.
This document provides instructions for disassembling and assembling the final drive of a D6N LGP track-type tractor. It describes:
1) Removing over 20 components of the final drive including carriers, planetary gears, seals, and sprockets.
2) Cleaning and inspecting removed parts.
3) Reassembling the final drive by installing components in the reverse order of removal while precisely positioning bearings and seals using specialized tools.
This document provides instructions for disassembling and assembling the final drive, steering differential, and brake on the left side of a D6N LGP track-type tractor. It lists the required tools and gives step-by-step details on removing components like the adapter, bolts, sprocket segment, and installing seals and bearings. The purpose is to guide maintenance technicians in properly servicing these systems while ensuring safety around hydraulic pressure.
This document provides instructions for disassembling and assembling the final drive of a D6N LGP track-type tractor. It describes:
1) Removing over 20 components of the final drive including carriers, planetary gears, seals, and sprockets by using various tools like brackets, pullers, and presses.
2) Assembling the components by lowering temperatures, inserting seals, and torquing bolts to specified values using the same tools.
3) Procedures for removing and installing the entire left side final drive, steering differential, and brake assembly, which weighs 680 kg.
The document provides instructions for removing the final drive, steering differential, and brake from the left side of a D6N track-type tractor. It lists the required tools and presents a 20-step procedure involving removing mounting bolts, shafts, gears, seals, and other components. Detailed illustrations accompany each step to show the correct positioning of tools and order of disassembly.
The document provides instructions for removing the final drive, steering differential, and brake from the left side of a D6N track-type tractor. It lists the required tools and presents a 20-step procedure involving removing mounting bolts, shafts, gears, seals, and other components. Detailed illustrations accompany each step to show the correct positioning of tools and order of disassembly.
The document provides instructions for removing the final drive, steering differential, and brake from the left side of a D6N track-type tractor. It lists the required tools and presents a 20-step procedure involving removing mounting bolts, shafts, gears, seals, and other components. Detailed illustrations accompany each step to show the correct positioning of tools and order of disassembly.
This document provides instructions for disassembling and assembling the final drive of a D6N XL track-type tractor. The disassembly process involves removing multiple components of the final drive including the carrier, planetary gears, ring gear, sprocket hub, and seals. The assembly process describes installing these components in reverse order and includes torque specifications for the bolts. Tools required include various brackets, pullers, and presses. Safety precautions are provided regarding the weight of components and hot hydraulic oil.
This document provides instructions for disassembling and assembling the final drive, steering differential, and brake of a D6N XL track-type tractor. The disassembly process involves using various tools to remove 20 bolts and nuts, as well as the carrier, shafts, gears, seals, and sprocket hub. The assembly is the reverse of the disassembly process and requires carefully lowering temperatures, applying lubricant, and tightening bolts to the specified torques.
This document provides instructions for disassembling and assembling the final drive of a D6N XL track-type tractor. The disassembly process involves removing multiple components of the final drive including the carrier, planetary gears, ring gear, sprocket hub, and seals. The assembly process describes installing these components in reverse order and includes details on using specialized tools and heating/cooling components as needed. Proper torque specifications are provided for reinstalling fasteners.
Caterpillar Cat D6T XL PAT TRACK-TYPE TRACTOR (Prefix WES) Service Repair Man...onyvzcwadtu05
1. The document provides instructions for disassembling and assembling components of the final drive, steering differential, and brake for a D6T Track-Type Tractor.
2. The disassembly procedure includes removing mounting bolts, seals, and using various specialty tools to separate internal components like carriers, gears, and shafts.
3. Reassembly is the reverse of disassembly, applying clean oil and torquing bolts to the specified values.
Caterpillar Cat D6T XL PAT TRACK-TYPE TRACTOR (Prefix WES) Service Repair Man...f8ioseoodkmmd
1. The document provides instructions for disassembling and assembling components of the final drive, steering differential, and brake for a D6T Track-Type Tractor.
2. The disassembly procedure includes removing mounting bolts, seals, and using various specialty tools to separate components like carriers, gears, and differentials.
3. Over a dozen individual steps are outlined for disassembly, and reassembly is instructed to be performed in reverse order while following specific torque specifications for bolts.
Caterpillar Cat D6T XL PAT TRACK-TYPE TRACTOR (Prefix WES) Service Repair Man...ze3xiandiao
1. The document provides instructions for disassembling and assembling components of the final drive, steering differential, and brake for a D6T Track-Type Tractor.
2. The disassembly procedure includes removing mounting bolts, seals, and using various specialty tools to separate individual components like hubs, gears, and carriers.
3. Over a dozen individual parts must be removed and numerous specialty installation and removal tools are required to fully disassemble the drive train components. Proper lubrication and torque specifications are also provided for reassembly.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fujsjefskekfksem
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...hfjsejdkemmn
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...ufuusjejfjkse
This document provides assembly instructions for installing a final drive on a D11T track-type tractor. It lists the required tools and parts and describes 40 steps to assemble the final drive, including heating and pressing components, installing seals and bearings, attaching hubs and gears, and torquing bolts. The final drive assembly involves multiple internal components and requires specialized tools and lifting equipment due to the assembly's weight.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fjjsiefksekm
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances between parts. Pictures accompany each step to illustrate the assembly process.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fujsjfjkskefsem
This document provides assembly instructions for installing a final drive on a D11T track-type tractor. It lists required tools and parts and describes 40 steps to assemble the final drive, including installing bearings, seals, gears, carriers, shafts and bolts. The final drive assembly is attached to the tractor using a lifting bracket and bolted into place, completing the installation.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fjjsjeskkekem
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fhsejkdkmen
This document provides assembly instructions for installing a final drive on a D11T track-type tractor. It lists required tools and parts and describes 40 steps to assemble the final drive, including installing bearings, seals, gears, carriers, shafts and bolts. The final drive assembly is attached to lifting brackets and lowered into position on the tractor, then bolted in place with specified torques.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fujsjefksekmfm
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
This document provides instructions for disassembling and assembling the final drives on a D7H track-type tractor. The process involves removing the final drives from the machine and then disassembling their internal components like planet carriers, gears, shafts and seals. Reassembly requires installing these components in reverse order and tightening bolts to the specified torques. Tools are used to assist with removing and installing heavy components like planet carriers and hubs.
The document provides instructions for disassembling and assembling the final drives of a D7H track-type tractor. Key steps include removing the final drives from the tractor frame using specialized tools, then disassembling the internal components like planet carriers, gears, and shafts. Reassembly involves heating bearings, installing seals and retaining rings, and using tools to position components as the final drives are rebuilt. Precautions are noted to prevent damage to seals during removal and installation of parts.
This document provides instructions for disassembling and assembling the final drive of a D9R track-type tractor. It describes removing components such as the planetary carrier, gears, shafts, and hub. Various tools are required, including link brackets, a push-puller tool group, driver group, and hydraulic cylinder assembly. Precautions are given for using hydraulic cylinders and puller studs during disassembly. The multi-step process includes pressing, lifting, and removing components from the planetary carrier, sun gear, and hub.
Volvo L220E Wheel Loader Service Repair Manual Instant Download.pdff8ioseoodkmmd
The document provides instructions for removing an engine from a machine. Key steps include:
1. Draining the coolant and engine, transmission, and hydraulic oils.
2. Disconnecting hoses, pipes, wires, and other components connected to the engine like the radiator, fuel lines, starter, and sensors.
3. Securing the transmission and attaching lifting tools and a device to the engine before removing mounting bolts.
4. Lifting out the engine once all connections are removed.
Volvo L220G Wheel Loader Service Repair Manual Instant Download.pdff8ioseoodkmmd
This document provides instructions for changing a non-programmed E-ECU (engine control unit) on an engine with MID 128. The steps include: placing the machine in service position 1, connecting the VCADS Pro programming tool, turning off voltage, removing covers, disconnecting connectors and hoses from the old ECU, replacing the ECU, reconnecting connectors and hoses, and finishing installation. Connectors are unplugged, cable clamps removed, cooling coil disconnected, old ECU replaced with new one, then cooling coil, connectors and clamps are reinstalled.
Volvo L220F Wheel Loader Service Repair Manual Instant Download.pdff8ioseoodkmmd
This document provides instructions for removing an engine from a machine. It describes draining fluids like coolant, engine oil, and transmission oil. It lists components that must be disconnected from the engine like hoses, wires, and sensors. Tools needed include lifting equipment and drain hoses. Safety precautions are noted, like placing the machine in service position and disconnecting the fire suppression system. Overall it provides a concise step-by-step process for removing an engine.
This document provides instructions for removing and installing a pilot control valve on a D10 track-type tractor. Key steps include:
1. Removing covers and disconnecting oil lines and control rods from the pilot control valve.
2. Removing bolts to detach the valve from its mounting bracket.
3. For installation, the process is reversed - the pilot control valve is mounted to the bracket with bolts, then oil lines and control rods are reconnected.
Volvo EC360C L EC360CL Excavator Service Repair Manual Instant Download.pdff8ioseoodkmmd
The document provides instructions for removing and installing an engine. It describes disconnecting hoses, electrical connections, removing mounting hardware and lifting the engine out. When installing, it describes connecting all hoses and electrical connections, installing mounting hardware, and filling fluids before starting the engine to check for leaks.
Volvo L50D Wheel Loader Service Repair Manual Instant Download.pdff8ioseoodkmmd
The document provides information on servicing an engine, including:
1. The engine is a four-stroke diesel with four cylinders and designation TD40GJE with a displacement of 4.0 liters.
2. Instructions are provided for checking and adjusting the valves, including valve clearances of 0.20mm for inlet and 0.45mm for exhaust.
3. Details are given for removing and installing the engine, which weighs approximately 450kg, including disconnecting hoses and mounts, using slings for lifting, and reconnecting all components.
Volvo EC380D L EC380DL Excavator Service Repair Manual Instant Download.pdff8ioseoodkmmd
This document provides information about engines D11H, D13H, and D16H. It describes the engines as straight six-cylinder, four-stroke diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation. The document discusses engine identification, automatic engine shutdown, engine protection functions, warning lights, torque limitation, forced idle, engine shutdown, and speed limits. It also lists relevant diagnostic codes and available VCADS Pro operations for testing components and exhaust aftertreatment systems.
More Related Content
Similar to Caterpillar Cat D6N TRACK-TYPE TRACTOR (Prefix CCS) Service Repair Manual Instant Download.pdf
This document provides instructions for disassembling and assembling the final drive of a D6N XL track-type tractor. The disassembly process involves removing multiple components of the final drive including the carrier, planetary gears, ring gear, sprocket hub, and seals. The assembly process describes installing these components in reverse order and includes details on using specialized tools and heating/cooling components as needed. Proper torque specifications are provided for reinstalling fasteners.
Caterpillar Cat D6T XL PAT TRACK-TYPE TRACTOR (Prefix WES) Service Repair Man...onyvzcwadtu05
1. The document provides instructions for disassembling and assembling components of the final drive, steering differential, and brake for a D6T Track-Type Tractor.
2. The disassembly procedure includes removing mounting bolts, seals, and using various specialty tools to separate internal components like carriers, gears, and shafts.
3. Reassembly is the reverse of disassembly, applying clean oil and torquing bolts to the specified values.
Caterpillar Cat D6T XL PAT TRACK-TYPE TRACTOR (Prefix WES) Service Repair Man...f8ioseoodkmmd
1. The document provides instructions for disassembling and assembling components of the final drive, steering differential, and brake for a D6T Track-Type Tractor.
2. The disassembly procedure includes removing mounting bolts, seals, and using various specialty tools to separate components like carriers, gears, and differentials.
3. Over a dozen individual steps are outlined for disassembly, and reassembly is instructed to be performed in reverse order while following specific torque specifications for bolts.
Caterpillar Cat D6T XL PAT TRACK-TYPE TRACTOR (Prefix WES) Service Repair Man...ze3xiandiao
1. The document provides instructions for disassembling and assembling components of the final drive, steering differential, and brake for a D6T Track-Type Tractor.
2. The disassembly procedure includes removing mounting bolts, seals, and using various specialty tools to separate individual components like hubs, gears, and carriers.
3. Over a dozen individual parts must be removed and numerous specialty installation and removal tools are required to fully disassemble the drive train components. Proper lubrication and torque specifications are also provided for reassembly.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fujsjefskekfksem
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...hfjsejdkemmn
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...ufuusjejfjkse
This document provides assembly instructions for installing a final drive on a D11T track-type tractor. It lists the required tools and parts and describes 40 steps to assemble the final drive, including heating and pressing components, installing seals and bearings, attaching hubs and gears, and torquing bolts. The final drive assembly involves multiple internal components and requires specialized tools and lifting equipment due to the assembly's weight.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fjjsiefksekm
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances between parts. Pictures accompany each step to illustrate the assembly process.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fujsjfjkskefsem
This document provides assembly instructions for installing a final drive on a D11T track-type tractor. It lists required tools and parts and describes 40 steps to assemble the final drive, including installing bearings, seals, gears, carriers, shafts and bolts. The final drive assembly is attached to the tractor using a lifting bracket and bolted into place, completing the installation.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fjjsjeskkekem
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fhsejkdkmen
This document provides assembly instructions for installing a final drive on a D11T track-type tractor. It lists required tools and parts and describes 40 steps to assemble the final drive, including installing bearings, seals, gears, carriers, shafts and bolts. The final drive assembly is attached to lifting brackets and lowered into position on the tractor, then bolted in place with specified torques.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fujsjefksekmfm
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
Similar to Caterpillar Cat D6N TRACK-TYPE TRACTOR (Prefix CCS) Service Repair Manual Instant Download.pdf (12)
This document provides instructions for disassembling and assembling the final drives on a D7H track-type tractor. The process involves removing the final drives from the machine and then disassembling their internal components like planet carriers, gears, shafts and seals. Reassembly requires installing these components in reverse order and tightening bolts to the specified torques. Tools are used to assist with removing and installing heavy components like planet carriers and hubs.
The document provides instructions for disassembling and assembling the final drives of a D7H track-type tractor. Key steps include removing the final drives from the tractor frame using specialized tools, then disassembling the internal components like planet carriers, gears, and shafts. Reassembly involves heating bearings, installing seals and retaining rings, and using tools to position components as the final drives are rebuilt. Precautions are noted to prevent damage to seals during removal and installation of parts.
This document provides instructions for disassembling and assembling the final drive of a D9R track-type tractor. It describes removing components such as the planetary carrier, gears, shafts, and hub. Various tools are required, including link brackets, a push-puller tool group, driver group, and hydraulic cylinder assembly. Precautions are given for using hydraulic cylinders and puller studs during disassembly. The multi-step process includes pressing, lifting, and removing components from the planetary carrier, sun gear, and hub.
Volvo L220E Wheel Loader Service Repair Manual Instant Download.pdff8ioseoodkmmd
The document provides instructions for removing an engine from a machine. Key steps include:
1. Draining the coolant and engine, transmission, and hydraulic oils.
2. Disconnecting hoses, pipes, wires, and other components connected to the engine like the radiator, fuel lines, starter, and sensors.
3. Securing the transmission and attaching lifting tools and a device to the engine before removing mounting bolts.
4. Lifting out the engine once all connections are removed.
Volvo L220G Wheel Loader Service Repair Manual Instant Download.pdff8ioseoodkmmd
This document provides instructions for changing a non-programmed E-ECU (engine control unit) on an engine with MID 128. The steps include: placing the machine in service position 1, connecting the VCADS Pro programming tool, turning off voltage, removing covers, disconnecting connectors and hoses from the old ECU, replacing the ECU, reconnecting connectors and hoses, and finishing installation. Connectors are unplugged, cable clamps removed, cooling coil disconnected, old ECU replaced with new one, then cooling coil, connectors and clamps are reinstalled.
Volvo L220F Wheel Loader Service Repair Manual Instant Download.pdff8ioseoodkmmd
This document provides instructions for removing an engine from a machine. It describes draining fluids like coolant, engine oil, and transmission oil. It lists components that must be disconnected from the engine like hoses, wires, and sensors. Tools needed include lifting equipment and drain hoses. Safety precautions are noted, like placing the machine in service position and disconnecting the fire suppression system. Overall it provides a concise step-by-step process for removing an engine.
This document provides instructions for removing and installing a pilot control valve on a D10 track-type tractor. Key steps include:
1. Removing covers and disconnecting oil lines and control rods from the pilot control valve.
2. Removing bolts to detach the valve from its mounting bracket.
3. For installation, the process is reversed - the pilot control valve is mounted to the bracket with bolts, then oil lines and control rods are reconnected.
Volvo EC360C L EC360CL Excavator Service Repair Manual Instant Download.pdff8ioseoodkmmd
The document provides instructions for removing and installing an engine. It describes disconnecting hoses, electrical connections, removing mounting hardware and lifting the engine out. When installing, it describes connecting all hoses and electrical connections, installing mounting hardware, and filling fluids before starting the engine to check for leaks.
Volvo L50D Wheel Loader Service Repair Manual Instant Download.pdff8ioseoodkmmd
The document provides information on servicing an engine, including:
1. The engine is a four-stroke diesel with four cylinders and designation TD40GJE with a displacement of 4.0 liters.
2. Instructions are provided for checking and adjusting the valves, including valve clearances of 0.20mm for inlet and 0.45mm for exhaust.
3. Details are given for removing and installing the engine, which weighs approximately 450kg, including disconnecting hoses and mounts, using slings for lifting, and reconnecting all components.
Volvo EC380D L EC380DL Excavator Service Repair Manual Instant Download.pdff8ioseoodkmmd
This document provides information about engines D11H, D13H, and D16H. It describes the engines as straight six-cylinder, four-stroke diesel engines equipped with a single variable geometry turbocharger and cooled external exhaust gas recirculation. The document discusses engine identification, automatic engine shutdown, engine protection functions, warning lights, torque limitation, forced idle, engine shutdown, and speed limits. It also lists relevant diagnostic codes and available VCADS Pro operations for testing components and exhaust aftertreatment systems.
This document provides instructions for disassembling and assembling the main hydraulic pump on a M315D Wheeled Excavator. The disassembly procedure involves 34 steps to remove all components of the pump. The assembly procedure involves 24 steps and specifies the required tools and order of installation for all pump components. Dimension measurements and calculations are provided to determine the correct lift-off limitation without shim.
- The document provides instructions for removing and installing the final drive planetary carrier in the chassis of a D9R track-type tractor.
- It describes using various tools to remove the carrier, hub, seals, and other components. It then explains how to prepare and install replacement parts in reverse order.
- Cleaning and inspecting all parts before installation is emphasized, along with properly positioning seals and applying lubricant to facilitate smooth assembly.
This document provides instructions to disassemble and assemble the final drive of a D9R track-type tractor. The disassembly process involves using various tools to remove over 30 components from the planetary carrier, sun gear, hub, and ring gear. The assembly process reverses the disassembly steps, heating some bearings before installation and using specialty tools to install seals and retainers. Proper safety precautions and inspection of parts is emphasized throughout.
This document provides instructions for assembling and installing the final drive on a D7R track-type tractor. It describes 31 steps for assembly, including installing seals, bearings, gears, shafts and covers. For installation, it outlines 10 steps such as positioning the final drive, installing bolts, filling it with oil and reconnecting the track. The document contains diagrams to illustrate each step in the process.
The document provides instructions for disassembling and assembling the steering clutch and brake of a Caterpillar D7R track-type tractor. It details 20 steps to disassemble the components which include removing bolts, plates, bearings, seals and other parts. The 20 steps to assemble are also outlined and include cleaning parts, applying oil, heating bearings, and reinstalling components in reverse order. Special safety precautions are noted regarding spring loaded components.
Caterpillar Cat D7R II TRACK-TYPE TRACTOR (Prefix AGN) Service Repair Manual ...f8ioseoodkmmd
The document provides instructions for removing and installing the final drive, steering planetary, and brake on a D7R II track-type tractor. The removal process includes draining the oil, removing covers, axles, and bolts. Special tools are required to lift the heavy assembly. Reinstallation requires cleaning seals, applying oil, and torquing bolts to the specified values. The overall process ensures the components are properly disassembled and reassembled.
Caterpillar Cat D7R II WATER FORDING TRACTOR (Prefix DJT) Service Repair Manu...f8ioseoodkmmd
This document provides instructions for disassembling and assembling the steering planetary and brake of a D7R Series II Water Fording Tractor. It describes removing 24 components including the planetary group, brake, ring gear, friction discs, piston, and springs. Reassembly is outlined in 25 steps, starting with installing springs and rings and ending by bolting the planetary group and brake to the final drive. Precautions and required tools are listed to correctly take apart and rebuild the steering and brake system.
The document suggests that if clicking the above button is invalid, the user should first download the document and then click the link to download the complete manual. It thanks the reader for their time.
The document provides instructions for disassembling and assembling the main hydraulic pump on an excavator. It lists required tools and parts and includes 43 detailed illustrations guiding the removal and installation of individual components in 49 steps. Proper assembly is important as improper installation of spring-loaded parts can cause injury. The pump controls hydraulic flow to power machine systems.
1) The document provides instructions for separating the upper frame and undercarriage frame on an excavator.
2) It lists required tools including stands, tubes, collars, pins, and an electric hydraulic pump.
3) The first steps are to place wheel chocks and use links and support beams to secure the tracks before separating the frames.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
1. Product: TRACK-TYPE TRACTOR
Model: D6N TRACK-TYPE TRACTOR CCS
Configuration: D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE) POWERED BY 3126B ENGINE
Disassembly and Assembly
D6N Track-Type Tractor Power Train
Media Number -RENR5257-04 Publication Date -01/12/2015 Date Updated -15/12/2015
i06691352
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 3
B 1P-0074 Slide Hammer Puller Gp 1
C
FT-1934 Puller Beam 1
- (16 mm x 190.5 mm) Bolt 4
5P-8247 Hard Washer 4
6V-3170 Double Acting Cylinder 1
9U-6600 Hand Hydraulic Pump 1
1P-0521 Driver Group 1
D 439-3940 Bracket As 2
Start By:
a. Remove the final drive.
1/6
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2. Illustration 1 g01234745
1. Attach Tooling (A) and a suitable lifting device to carrier (1). The weight of carrier (1) is
approximately 50 kg (110 lb).
2. Remove bolts (2) and carrier (1) from sprocket hub (3). Position carrier (1) onto suitable
cribbing.
Illustration 2 g01234760
3. Remove bolt (4), the washer, the retainer, and the O-ring seal from carrier (1).
4. Use a suitable press to remove shaft (5) from carrier (1).
5. Repeat Steps 3 and 4 for the remaining shafts.
2/6
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 3 g06077476
6. Remove planetary gear (8) from carrier (1).
7. Remove bearing cones (6) and (9) from planetary gear (8).
8. Remove bearing cups (7) from planetary gear (8).
9. Repeat Steps 6 through 8 for the remaining planetary gears.
3/6
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00988981
10. Remove bolts (10) and retainer (11).
11. Remove ring gear hub (12) and ring gear (13).
Illustration 5 g00988984
12. Remove ring (14) and ring gear hub (12) from ring gear (13).
Illustration 6 g00988985
13. Use Tooling (B) to remove bushing (15) and lip-type seal (16) (not shown).
4/6
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g00988979
14. Raise the temperature of bearing cone (17).
15. Use Tooling (C) to remove bearing cone (17) from the spindle.
Note: Do not lift the sprocket hub so that the sprocket hub contacts the fittings that are on
the hydraulic cylinder. Damage to the fittings could occur.
16. Remove Tooling (C).
Illustration 8 g01235181
17. Attach Tooling (D) and a suitable lifting device to sprocket hub (3). The weight of sprocket
hub (3) is approximately 135 kg (298 lb). Remove sprocket hub (3) from the spindle.
5/6
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g01235238
18. Remove bearing cups (18) and (19) from sprocket hub (3).
19. Remove Duo-cone seal (20) from sprocket hub (3).
Illustration 10 g01235241
20. Remove Duo-cone seal (22) from spindle (23).
21. Remove bearing cone (21) from spindle (23).
6/6
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Product: TRACK-TYPE TRACTOR
Model: D6N TRACK-TYPE TRACTOR CCS
Configuration: D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE) POWERED BY 3126B ENGINE
Disassembly and Assembly
D6N Track-Type Tractor Power Train
Media Number -RENR5257-04 Publication Date -01/12/2015 Date Updated -15/12/2015
i03902166
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
D 138-7575 Link Bracket 2
E 1P-0520 Driver Gp 1
F
169-0503 Installation Kit 1
8M-9395 Seal Installer 1
G 1U-7234 Feeler Gauge 1
1/7
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g01235241
1. Raise the temperature of bearing cone (21). Install bearing cone (21) onto spindle (23).
2. Use Tooling (F) (not shown) in order to install Duo-cone seal (22). Refer to Disassembly
and Assembly, "Duo-Cone Conventional Seals - Install".
Illustration 2 g01235238
3. Lower the temperature of bearing cups (19) and (18).
4. Install bearing cups (19) and (18) in hub (3).
5. Use Tooling (F) (not shown) in order to install Duo-cone seal (20) in hub (3). Refer to
Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
2/7
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 3 g01235181
6. Install Tooling (D) and a suitable lifting device to hub (3). Install hub (3) onto the spindle.
The weight of hub (3) is approximately 135 kg (298 lb).
Illustration 4 g00990323
7. Install lip seal (16) and sleeve bearing (15).
3/7
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 6 g02145273
9. Raise the temperature of bearing cone (17). Install bearing cone (17) on the spindle.
10. Install hub (12) and gear (13) as an assembly.
11. Install retainer (11) and bolts (10). Tighten all bolts (10) in a star pattern. Tighten bolts (10)
to a torque of 120 ± 20 N·m (89 ± 15 lb ft). Continually rotate hub (12) in order to properly
seat bearing cone (17). Tighten bolts (10) to a torque of 120 ± 20 N·m (89 ± 15 lb ft) in
order to ensure the proper torque.
12. Use Tooling (G) (not shown) in order to verify that the spindle is touching the retainer.
13. If necessary, repeat Step 11 and Step 12 in order to verify that bearing cone (17) is seated
properly.
5/7
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 7 g01234812
14. Lower the temperature of bearing cups (7). Install bearing cups (7) into gear (8).
15. Position bearing cones (6) and (9) into gear (8).
16. Position gear (8) into carrier (1).
Illustration 8 g01235164
17. Lower the temperature of shaft (5). Use a suitable press in order to install shaft (5). Install
shaft (5) until the end of the shaft is flush with the outer surface of carrier (1).
18. Install bolt (4) and the plate to carrier (1).
19. Verify that there is metal to metal contact between plates (4) and the shafts.
6/7
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 20. Repeat Steps 17 through 19 for the remaining shafts.
Illustration 9 g01234745
21. Attach Tooling (A) to carrier (1). Position carrier (1) into hub (3). The weight of carrier (1)
is approximately 41 kg (90 lb).
22. Install bolts (2).
23. Remove Tooling (A).
End By:
a. Install the final drive. Refer to Disassembly and Assembly, "Final Drive - Install".
7/7
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Product: TRACK-TYPE TRACTOR
Model: D6N TRACK-TYPE TRACTOR CCS
Configuration: D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE) POWERED BY 3126B ENGINE
Disassembly and Assembly
D6N Track-Type Tractor Power Train
Media Number -RENR5257-04 Publication Date -01/12/2015 Date Updated -15/12/2015
i01896906
Final Drive - Install
SMCS - 4050-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8T-3207 Lifting Bracket 1
5P-8622 Shackle 1
9S-9076 Spacer 1
7X-2557 Bolt 2
Illustration 1 g00956633
1. Adjust bracket (1) until Dimension (X) is equal to 80 mm (3.0 inch).
1/3
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. End By:
a. Install the axle. Refer to Disassembly and Assembly, "Axle - Install".
b. Connect the track. Refer to Disassembly and Assembly, "Track - Connect".
3/3
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Product: TRACK-TYPE TRACTOR
Model: D6N TRACK-TYPE TRACTOR CCS
Configuration: D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE) POWERED BY 3126B ENGINE
Disassembly and Assembly
D6N Track-Type Tractor Power Train
Media Number -RENR5257-04 Publication Date -01/12/2015 Date Updated -15/12/2015
i01905492
Final Drive, Steering Differential, and Brake (Left Side) -
Remove
SMCS - 4050-011-LT; 4131-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 154-6181 Forcing Screw 3
B 8T-3207 Lifting Bracket 1
C 138-7575 Link Bracket 1
D 8S-9906 Ratchet Puller 1
Start By:
a. Separate the track. Refer to Disassembly and Assembly, "Track - Separate".
b. Remove the steering motor. Refer to Disassembly and Assembly, "Steering Motor -
Remove".
c. Remove the axles. Refer to Disassembly and Assembly, "Axle - Remove and Install".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
NOTICE
1/5
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
Illustration 1 g00992346
1. Remove bolts (1).
2/5
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g00992348
2. Install Tooling (A) and remove housing (2).
Illustration 3 g00992349
3. Remove two bolts (3) and bolt (4) in order to install Tooling (C). Remove two bolts (5).
Illustration 4 g00865077
4. Remove bolts (6) from the top of the sprocket segment.
3/5
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 5 g00994019
5. Install Tooling (B). Adjust the hook of Tooling (B) to the maximum length.
Illustration 6 g00992350
6. Remove remaining bolts (3) and the washers.
Illustration 7 g00992351
7. Attach Tooling (D) to Tooling (C) and Tooling (B).
8. Separate the final drive approximately 152 mm (6.0 inch).
4/5
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 9. Release the pressure on Tooling (D). Rotate the brake housing 90 degrees in the
counterclockwise direction.
Illustration 8 g00992352
10. Rotating the brake housing allows pinion (7) to point forward. Rotating the brake housing
will allow the final drive to swing toward the front of the machine. Rotating the brake
housing will allow clearance for the ring gear to clear the machine. The weight of the final
drive assembly is approximately 680 kg (1500 lb).
5/5
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Product: TRACK-TYPE TRACTOR
Model: D6N TRACK-TYPE TRACTOR CCS
Configuration: D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE) POWERED BY 3126B ENGINE
Disassembly and Assembly
D6N Track-Type Tractor Power Train
Media Number -RENR5257-04 Publication Date -01/12/2015 Date Updated -15/12/2015
i06983810
Steering Differential and Brake - Disassemble
SMCS - 4131-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Description Qty
A 138-7573 Link Bracket 2
B 3K-4897 Spring Pin 8
C 6V-4072 Spanner Wrench 1
D
9S-9154 Step Plate 1
6V-3009 Bar 1
8S-6470 Forcing Screw 1
8S-5133 Plug 1
5P-8245 Washer 4
1D-4719 Full Nut 2
2H-6488 Bolt 2
E 9S-9154 Step Plate 1
6V-3009 Bar 1
8S-6470 Forcing Screw 1
8S-5133 Plug 1
5P-8245 Washer 4
1/22
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 1D-4719 Full Nut 2
1D-4574 Bolt 2
8H-0663 Bearing Puller 1
F 138-7575 Link Bracket 3
G
8B-7550 Leg 2
8B-7559 Adapter 2
3H-0465 Plate 4
1P-0498 Plate 1
1B-4207 Full Nut 2
5H-9976 Screw 1
5B-0637 High Idle Nut 1
8H-0684 Ratchet Wrench 1
8B-7563 Handle 1
5F-7353 Washer 1
8B-7548 Push-Puller Tool Gp 1
Start By:
a. Remove the left final drive, the steering differential, and the brake. Refer to Disassembly
and Assembly, "Final Drive, Steering Differential, and Brake (Left Side) - Remove"
.
2/22
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g00993890
1. Remove bolts (1) and the washers.
2. Remove two opposite bolts (2).
3/22
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 2 g00823691
3. Install Tooling (A) and a suitable lifting device.
4. Remove sliding carrier (3). The weight of sliding carrier (3) is approximately 48 kg
(105 lb).
5. Remove Tooling (A).
4/22
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 3 g06187075
6. Remove remaining bolts (2) and slinger (4) from planetary carrier (7).
7. Remove retaining ring (5), thrust ring (5A), and planetary carrier (7) from ring gear (6).
Illustration 4 g00823775
8. Remove O-ring seal (10) from planetary carrier (7).
9. Use a hammer and a punch to push pin (12) in shaft (11).
10. Remove shaft (11), planetary gear (9), discs (8), and bearing (13) from planetary carrier (7).
11. Remove pin (12) from shaft (11).
12. Repeat Steps 9 through 11 for the remaining planetary gears.
5/22
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 5 g00823759
13. Remove lockring (14) and remove retaining ring (16).
14. Remove sun gear (15) from planetary carrier (18).
15. Remove spacer (17).
6/22
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
29. Illustration 6 g00995126
16. Remove bolts (19), plate (20), and gear (21) from planetary carrier (18).
17. Use Tooling (B) to compress the retaining ring that holds planetary carrier (18) in ring gear
(6).
18. Separate planetary carrier (18) from ring gear (6).
19. Remove the retaining ring from planetary carrier (18).
20. Use a hammer and a punch to push pin (23) in shaft (24).
7/22
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CCS00001-UP (MACHINE)...
2021/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...