This document provides instructions for removing and installing various components of the crankshaft assembly for a 930M wheel loader powered by a C7.1 engine, including:
- Removing and installing the vibration damper and pulley
- Removing and installing the crankshaft front seal
- Removing and installing the front cover
The procedures describe the required tools, removal steps, inspection criteria, and installation steps for each component in 3 sentences or less.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Digital Fleet Management - Why Your Business Need It?
Caterpillar Cat 930M WHEEL LOADER (Prefix KTG) Service Repair Manual Instant Download (KTG00001 and up).pdf
1. Product: WHEEL LOADER
Model: 930M WHEEL LOADER KTG
Configuration: 930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05909511
Vibration Damper and Pulley - Remove
SMCS - 1205-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M14 x 1.5 by 100 mm
1
B 227-4393 E18 Torx Socket 1
Start By:
A. Remove the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt - Remove
and Install" for the correct procedure.
Note: The weight of the assembly of the crankshaft pulley, the vibration damper, and the
crankshaft adapter is approximately 22 kg (48 lb).
1/3
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2. Illustration 1 g02368017
1. Use a suitable tool in order to prevent the crankshaft from rotating. Use Tooling (B) to
remove one Torx screws (1) from crankshaft pulley assembly (2) .
2. Install Tooling (A) into crankshaft pulley assembly (2) .
3. Remove remaining Torx screws (1) from crankshaft pulley assembly (2) .
4. Remove crankshaft pulley assembly (2) .
5. Remove Tooling (A) .
2/3
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g02368018
6. If necessary, follow Step 6.a through Step 6.b in order to remove friction shim (3) from the
crankshaft.
a. Remove the front seal from the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
b. Remove friction shim (3) .
7. If necessary, follow Step 7.a through Step 7.c in order to disassemble vibration damper,
crankshaft pulley from crankshaft adapter.
a. Place the crankshaft pulley assembly onto a suitable support.
b. Remove bolts (7) from crankshaft pulley assembly (2) .
c. Remove vibration damper (6) and crankshaft pulley (5) from adapter (4) .
3/3
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Product: WHEEL LOADER
Model: 930M WHEEL LOADER KTG
Configuration: 930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05909517
Vibration Damper and Pulley - Install
SMCS - 1205-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M14 x 1.5 by 100 mm
1
B 227-4393 E18 Torx Socket 1
C 8T-3052 Degree Wheel 1
D -
Guide Studs
M12 x 1.75 by 50 mm
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g02368018
1. Ensure that the crankshaft adapter and the front of the crankshaft are clean and free from
damage.
2. Inspect vibration damper (6) for damage. If necessary, replace the vibration damper.
3. If necessary, follow Step 3.a through Step 3.f in order to install vibration damper, crankshaft
pulley to crankshaft adapter.
a. Place crankshaft adapter (4) onto a suitable support.
b. Install Tooling (D) crankshaft adapter (4) .
c. Install crankshaft pulley (5) and vibration damper (6) over Tooling (D) .
d. Install bolts (7) to the crankshaft pulley assembly.
Note: Evenly space bolts (7) around the crankshaft pulley assembly.
e. Remove Tooling (D) .
f. Tighten bolts (7) to a torque of 115 N·m (85 lb ft).
4. If necessary, install friction shim (3) . Follow Step 4.a through Step 4.b in order to install
friction shim (3) .
a. Install friction shim (3) .
2/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. b. Install a new front seal to the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
5. Install Tooling (A) to the crankshaft.
Illustration 2 g02368017
6. Install crankshaft pulley assembly (2) onto the crankshaft.
7. Install one Torx screws (1) to crankshaft pulley assembly (2) hand tighten.
8. Remove Tooling (A) .
9. Install remaining Torx screws (1) to crankshaft pulley assembly (2) .
10. Use a suitable tool in order to prevent the crankshaft from rotating. Tighten Torx screws (1)
to a torque of 40 N·m (29 lb ft).
11. Use Tooling (B) and Tooling (C) to turn Torx screws (1) through an additional 120 degrees.
End By: Install the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt -
Remove and Install" for the correct procedure.
3/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Product: WHEEL LOADER
Model: 930M WHEEL LOADER KTG
Configuration: 930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05018646
Crankshaft Front Seal - Remove and Install - Crankshaft
Front Seal for Heavy Duty Front Cover
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 278-2636 Front Oil Seal Removal Tool 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Remove" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g02048634
1. Position Tooling (A) on the nose of the crankshaft. Screw Tooling (A) into crankshaft front
seal (2).
Note: Do not damage the edge of the front cover for the crankshaft front seal.
2. Screw the bolt into Tooling (A) in order to remove crankshaft front seal (2) from front cover
(1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B
9U-6206 Stud Front Seal Installer 1
9U-6207 Plate 1
9U-6209 Sleeve Plate 1
9U-6211 Seal Installer Tool 1
366-5984 Installer Assembly 1
2/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the bore for the crankshaft front oil seal in the front cover is clean and free from
damage.
Illustration 2 g03417117
2. Assemble Tooling (B).
3. Correctly position a new crankshaft front seal (2) to front cover (1).
Note: If the crankshaft front seal is supplied with a sleeve, remove the sleeve from the
crankshaft front seal before installation.
4. Use Tooling (B) to install crankshaft front seal (2) to front cover (1). Ensure that the front
face of the crankshaft front seal is installed to a depth of 6.5 ± 0.2 mm (0.256 ± 0.008 inch).
5. Remove Tooling (B) from the crankshaft.
End By:
3/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Install" for the correct procedure.
4/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Product: WHEEL LOADER
Model: 930M WHEEL LOADER KTG
Configuration: 930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i06799526
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 367-3534 Oil Seal Removal & Installer Tool 1
B 207-1601 P-80 Rubber Lubricant 1
Start By:
a. Remove the crankshaft vibration damper and pulley.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g03417118
1. Position Tooling (A) onto crankshaft front seal (2).
2. Turn Tooling (A) in a counterclockwise direction and remove crankshaft front seal (2) from
front cover (1).
Installation Procedure
1. Ensure that the front cover is clean and free from damage.
2/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 2 g03417120
3/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g03453516
2. Apply Tooling (B) to static twin dead seal (3) (not shown) to a new crankshaft front seal (2).
Ensure that none of Tooling (B) contaminates the crankshaft front seal in Position (Y).
3. Correctly position a new crankshaft front seal (2) in Position (X) onto front cover (1).
4. Position Tooling (A) onto crankshaft front seal (2).
5. Use Tooling (A) to turn crankshaft front seal (2) in a clockwise direction.
6. If a torque that is greater than 50 N·m (37 lb ft) is necessary to install crankshaft front seal
(2), remove crankshaft front seal (2). Inspect crankshaft front seal (2) and front cover (1) for
faults or damage.
7. If necessary, repeat Step 2 through Step 6 to install crankshaft front seal (2).
End By:
a. Install the crankshaft vibration damper and pulley.
4/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Product: WHEEL LOADER
Model: 930M WHEEL LOADER KTG
Configuration: 930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05018648
Front Cover - Remove and Install - Heavy Duty Front Cover
SMCS - 1166-010
Removal Procedure
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Remove" for the correct procedure.
b. If the engine is equipped with a fan, remove the fan. Refer to Disassembly and Assembly,
"Fan - Remove and Install" for the correct procedure.
c. Remove the front seal. Refer to Disassembly and Assembly, "Crankshaft Front Seal -
Remove and Install" for the correct procedure.
1/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g02048613
1. Remove bolts (3) and bolts (4). Identify the positions of bolts of different length.
2. Remove front cover (1) from the front housing.
3. Remove gasket (2) from front cover (1).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Studs
M8 by 70 mm
2
B 364-7210 Front Cover Alignment Tool 1
2/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 2 g02190213
1. Ensure that all components are clean and free from damage. Replace any damaged
components.
2. Thoroughly clean the gasket surface of the front housing.
3. Thoroughly clean front cover (1).
4. Install Tooling (A) into Holes (X) in the front housing.
5. Install a new gasket (2) onto Tooling (A).
6. Install front cover (1) onto Tooling (A).
7. Install bolts (3) and bolts (4) finger tight. Ensure that the bolts of different length are
installed in the correct positions.
8. Use Tooling (B) to align the front cover assembly.
3/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 9. Remove Tooling (A) and install remaining bolts (4).
10. Tighten bolts (3) and bolts (4) to a torque of 22 N·m (195 lb in).
11. Remove Tooling (B).
12. Install a new front seal to the front cover. Refer to Disassembly and Assembly, "Crankshaft
Front Seal - Remove and Install" for the correct procedure.
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Install" for the correct procedure.
b. If the engine was equipped with a fan, install the fan. Refer to Disassembly and Assembly,
"Fan - Remove and Install" for the correct procedure.
4/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Product: WHEEL LOADER
Model: 930M WHEEL LOADER KTG
Configuration: 930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i07167344
Front Cover - Remove and Install
SMCS - 1166-010
Removal Procedure
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Remove" for the correct procedure.
b. If the engine is equipped with a fan, remove the fan. Refer to Disassembly and Assembly,
"Fan - Remove and Install" for the correct procedure.
1/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g01992013
1. Remove the front seal from the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
2. Remove bolts (3) and bolts (4). Identify the positions of bolts of different length.
3. Remove front cover (1) from the front housing.
4. Remove gasket (2) from front cover (1).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M8 by 70 mm
2
B 367-3535 Front Cover Alignment Tool 1
2/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 2 g02190133
1. Thoroughly clean the gasket surface of the front housing.
2. If the original front cover is installed, follow Step 2.a through Step 2.b.
a. Thoroughly clean front cover (1).
b. Install a new gasket (2) to front cover (1). Engage Locators (Y) into the holes in the
front cover.
3. Install Tooling (A) into Holes (X) in the front housing.
4. Use Tooling (A) to position the front cover assembly onto the front housing.
5. Install bolts (3) and bolts (4) finger tight. Ensure that the bolts of different length are
installed in the correct positions.
3/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 6. Install a new front seal to the front cover. Refer to Disassembly and Assembly, "Crankshaft
Front Seal - Remove and Install" for the correct procedure.
7. Use Tooling (B) to align the front cover.
8. Remove Tooling (A) and install remaining bolts (4).
9. Tighten bolts (3) and bolts (4) to a torque of 22 N·m (195 lb in).
10. Remove Tooling (B) from the front cover.
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Install" for the correct procedure.
b. If the engine was equipped with a fan, install the fan. Refer to Disassembly and Assembly,
"Fan - Remove and Install" for the correct procedure.
4/4
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Suggest:
For more complete manuals. Please go to
the home page.
https://www.ebooklibonline.com
If the above button click is invalid. Please
download this document first, and then
click the above link to download the
complete manual.
Thank you so much for reading
24. Product: WHEEL LOADER
Model: 930M WHEEL LOADER KTG
Configuration: 930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05018649
Gear Group (Front) - Remove and Install
SMCS - 1206-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 364-9107 Fuel Injection Pump Timing Pin 1
D
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
E 298-5564 T40 Torx Socket 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
Start By:
a. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure.
b. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install" for the correct procedure.
1/14
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable. Care must be taken in
order to ensure that the fuel injection pump timing is not lost during the removal of the front gear
group. Carefully follow the procedure in order to remove the gear group.
2/14
930M Small Wheel Loader KTG00001-UP (MACHINE) POWERED BY C7.1 Engine...
2022/5/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...