The document provides instructions for removing and installing various components of a Caterpillar C7.1 engine, including the vibration damper and pulley, crankshaft front seal, and front cover. The removal procedures involve using various tools to remove screws, bolts, seals and other parts. The installation procedures specify cleaning components, installing new seals and gaskets, and tightening bolts to the specified torques.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...f8uejkdkdmm3e
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Heating and installing the ring gear if removed, then installing the flywheel using guide studs and lifting equipment. Tightening bolts to the specified torque and reinstalling the electric starting motor.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...f89siekkmdmm2w
The document provides instructions for removing and installing a flywheel on a C7.1 engine. To remove the flywheel, bolts must first be removed from the flywheel using guide studs for support. The flywheel can then be lifted off and inspected. To install the flywheel, any removed components like the ring gear must first be reinstalled on the flywheel. The flywheel is then positioned using guide studs and lifting devices, and bolts are tightened to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...jfkekd9d8di
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...f8uesjdkdmdm
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...udjkskmdm4e
The document provides instructions for removing and installing a flywheel on a C7.1 engine. To remove the flywheel, bolts must first be removed from the flywheel using guide studs for support. The flywheel can then be lifted off using a suitable lifting device. When installing the flywheel, guide studs are again used to support the flywheel as bolts are reinstalled and tightened to the specified torque. The condition of the flywheel and ring gear is also checked during removal and installation.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...8sjkdkdmdmdm
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...mtox80484546
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...yin9niaojiao
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...f8uejkdkdmm3e
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Heating and installing the ring gear if removed, then installing the flywheel using guide studs and lifting equipment. Tightening bolts to the specified torque and reinstalling the electric starting motor.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...f89siekkmdmm2w
The document provides instructions for removing and installing a flywheel on a C7.1 engine. To remove the flywheel, bolts must first be removed from the flywheel using guide studs for support. The flywheel can then be lifted off and inspected. To install the flywheel, any removed components like the ring gear must first be reinstalled on the flywheel. The flywheel is then positioned using guide studs and lifting devices, and bolts are tightened to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...jfkekd9d8di
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...f8uesjdkdmdm
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...udjkskmdm4e
The document provides instructions for removing and installing a flywheel on a C7.1 engine. To remove the flywheel, bolts must first be removed from the flywheel using guide studs for support. The flywheel can then be lifted off using a suitable lifting device. When installing the flywheel, guide studs are again used to support the flywheel as bolts are reinstalled and tightened to the specified torque. The condition of the flywheel and ring gear is also checked during removal and installation.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...8sjkdkdmdmdm
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...mtox80484546
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...yin9niaojiao
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...shibi1322
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...fujsekmd9dik
The document provides instructions for removing and installing a flywheel on a C7.1 engine. To remove the flywheel, bolts must first be removed from the flywheel using guide studs for support. The flywheel can then be lifted off using a suitable lifting device. When installing the flywheel, guide studs are again used to support the flywheel as bolts are reinstalled and tightened to the specified torque. The condition of the flywheel and ring gear is also checked during removal and installation.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...fucheng89
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...8foskkdjdkdm3e
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...nkikou1545
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
JOHN DEERE 430 LAWN GARDEN TRACTOR Service Repair Manual Instant Download (TM...jiuliu14811471
The document provides service information for John Deere 322, 330, 332, and 430 lawn and garden tractors, including safety guidelines, specifications, repair specifications and torque values, fuel and lubricant recommendations, and diagnostic and testing procedures. It is intended as a technical manual for experienced technicians to service these tractor models. The manual contents are organized into sections covering general information, engine repair, electrical systems, power train, steering/brakes, hydraulics, and diagnostics.
JOHN DEERE 332 LAWN GARDEN TRACTOR Service Repair Manual Instant Download (TM...jiuliu14811471
The document provides service information for John Deere 322, 330, 332, and 430 lawn and garden tractors, including safety guidelines, specifications, repair specifications and torque values, fuel and lubricant recommendations, and diagnostic and testing procedures. It is intended as a technical manual for experienced technicians performing maintenance and repairs. Safety messages throughout warn of hazards involving high pressure fluids, battery explosions, fire risks, and preventing acid burns or injuries.
JOHN DEERE 330 LAWN GARDEN TRACTOR Service Repair Manual Instant Download (TM...jiuliu14811471
The document provides service information for John Deere 322, 330, 332, and 430 lawn and garden tractors, including safety guidelines, specifications, repair specifications and torque values, fuel and lubricant recommendations, and diagnostic and testing procedures. It is intended as a technical manual for experienced technicians to service these tractor models. The manual contents are organized into sections covering general information, engine repair, electrical systems, power train, steering/brakes, hydraulics, and diagnostics.
JOHN DEERE 322 LAWN GARDEN TRACTOR Service Repair Manual Instant Download (TM...jiuliu14811471
The document provides service information for John Deere 322, 330, 332, and 430 lawn and garden tractors, including safety guidelines, specifications, repair specifications and torque values, fuel and lubricant recommendations, and diagnostic and testing procedures. It is intended as a technical manual for experienced technicians to service these tractor models. The manual contents are organized into sections covering general information, engine repair, electrical systems, power train, steering/brakes, hydraulics, and diagnostics.
John Deere 261 and 272 Rear-Mounted Mowers Service Repair Manual Instant Down...jiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 74 and 84 Blades Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
John Deere 54D, 60D, 62D AND 72D OnRamp Mowers Service Repair Manual Instant ...jiuliu14811471
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
John Deere 54D, 60D and 72 Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
John Deere 54, 60 and 72-Inch Mid Mount Mowers Service Repair Manual Instant ...jiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 47 and 59 Snowbowers Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 31B Post Hole Digger Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 26 and 51-Inch Brooms Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 5E 2BV Blower Service Repair Manual Instant Download (TM1430).pdfjiuliu14811471
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, listing details like engine type, displacement, speed ranges, components, and dimensions for each model. Safety guidelines are also provided, advising users to keep others away from operating equipment, avoid overreaching or pointing tools at people, and always shut off engines before adjusting or refueling.
The document provides instructions for disassembling a cylinder head from a D11N track-type tractor. The procedures include removing inlet and exhaust valves, bridge dowels, valve seat inserts, valve guides, and valve lifters. Tools required are listed for each step. Safety notices emphasize keeping parts clean and wearing protective equipment when compressing valve springs.
The document is a service manual that provides instructions for removing and installing the high-low transmission on a D8L track-type tractor. It details over 50 steps to disassemble the transmission down to individual components and then reassemble. These include draining fluids, removing mounting hardware, disconnecting wiring and hoses, using specialty tools to separate interconnected pieces, cleaning and inspecting parts, and precisely reinstalling components in the reverse order.
The document provides instructions for removing and installing the bulldozer blade on a D6R Track-Type Tractor. The key steps include:
1. Disconnecting hydraulic hoses from the manifold and capping the connections.
2. Removing bolts, caps, and shims from the lift cylinders and stabilizer link.
3. Installing tooling under the push arms and using it to support the bulldozer blade.
4. Removing mounting bolts to detach the bulldozer blade from the tractor frame.
More Related Content
Similar to Caterpillar Cat 329E Excavator (Prefix PTY) Service Repair Manual Instant Download.pdf
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...shibi1322
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...fujsekmd9dik
The document provides instructions for removing and installing a flywheel on a C7.1 engine. To remove the flywheel, bolts must first be removed from the flywheel using guide studs for support. The flywheel can then be lifted off using a suitable lifting device. When installing the flywheel, guide studs are again used to support the flywheel as bolts are reinstalled and tightened to the specified torque. The condition of the flywheel and ring gear is also checked during removal and installation.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...fucheng89
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...8foskkdjdkdm3e
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...nkikou1545
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Similar to Caterpillar Cat 329E Excavator (Prefix PTY) Service Repair Manual Instant Download.pdf (6)
JOHN DEERE 430 LAWN GARDEN TRACTOR Service Repair Manual Instant Download (TM...jiuliu14811471
The document provides service information for John Deere 322, 330, 332, and 430 lawn and garden tractors, including safety guidelines, specifications, repair specifications and torque values, fuel and lubricant recommendations, and diagnostic and testing procedures. It is intended as a technical manual for experienced technicians to service these tractor models. The manual contents are organized into sections covering general information, engine repair, electrical systems, power train, steering/brakes, hydraulics, and diagnostics.
JOHN DEERE 332 LAWN GARDEN TRACTOR Service Repair Manual Instant Download (TM...jiuliu14811471
The document provides service information for John Deere 322, 330, 332, and 430 lawn and garden tractors, including safety guidelines, specifications, repair specifications and torque values, fuel and lubricant recommendations, and diagnostic and testing procedures. It is intended as a technical manual for experienced technicians performing maintenance and repairs. Safety messages throughout warn of hazards involving high pressure fluids, battery explosions, fire risks, and preventing acid burns or injuries.
JOHN DEERE 330 LAWN GARDEN TRACTOR Service Repair Manual Instant Download (TM...jiuliu14811471
The document provides service information for John Deere 322, 330, 332, and 430 lawn and garden tractors, including safety guidelines, specifications, repair specifications and torque values, fuel and lubricant recommendations, and diagnostic and testing procedures. It is intended as a technical manual for experienced technicians to service these tractor models. The manual contents are organized into sections covering general information, engine repair, electrical systems, power train, steering/brakes, hydraulics, and diagnostics.
JOHN DEERE 322 LAWN GARDEN TRACTOR Service Repair Manual Instant Download (TM...jiuliu14811471
The document provides service information for John Deere 322, 330, 332, and 430 lawn and garden tractors, including safety guidelines, specifications, repair specifications and torque values, fuel and lubricant recommendations, and diagnostic and testing procedures. It is intended as a technical manual for experienced technicians to service these tractor models. The manual contents are organized into sections covering general information, engine repair, electrical systems, power train, steering/brakes, hydraulics, and diagnostics.
John Deere 261 and 272 Rear-Mounted Mowers Service Repair Manual Instant Down...jiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 74 and 84 Blades Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
John Deere 54D, 60D, 62D AND 72D OnRamp Mowers Service Repair Manual Instant ...jiuliu14811471
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
John Deere 54D, 60D and 72 Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
John Deere 54, 60 and 72-Inch Mid Mount Mowers Service Repair Manual Instant ...jiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 47 and 59 Snowbowers Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 31B Post Hole Digger Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 26 and 51-Inch Brooms Service Repair Manual Instant Download.pdfjiuliu14811471
This technical manual provides information for experienced technicians on John Deere commercial and consumer equipment, including specifications, safety information, and diagrams. It is organized systematically to keep all information for a particular system together. The manual is intended as a reference for technicians to service and maintain the listed equipment properly.
John Deere 5E 2BV Blower Service Repair Manual Instant Download (TM1430).pdfjiuliu14811471
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, listing details like engine type, displacement, speed ranges, components, and dimensions for each model. Safety guidelines are also provided, advising users to keep others away from operating equipment, avoid overreaching or pointing tools at people, and always shut off engines before adjusting or refueling.
The document provides instructions for disassembling a cylinder head from a D11N track-type tractor. The procedures include removing inlet and exhaust valves, bridge dowels, valve seat inserts, valve guides, and valve lifters. Tools required are listed for each step. Safety notices emphasize keeping parts clean and wearing protective equipment when compressing valve springs.
The document is a service manual that provides instructions for removing and installing the high-low transmission on a D8L track-type tractor. It details over 50 steps to disassemble the transmission down to individual components and then reassemble. These include draining fluids, removing mounting hardware, disconnecting wiring and hoses, using specialty tools to separate interconnected pieces, cleaning and inspecting parts, and precisely reinstalling components in the reverse order.
The document provides instructions for removing and installing the bulldozer blade on a D6R Track-Type Tractor. The key steps include:
1. Disconnecting hydraulic hoses from the manifold and capping the connections.
2. Removing bolts, caps, and shims from the lift cylinders and stabilizer link.
3. Installing tooling under the push arms and using it to support the bulldozer blade.
4. Removing mounting bolts to detach the bulldozer blade from the tractor frame.
Caterpillar Cat D4HTSK III TRACK SKIDDER (Prefix 7PK) Service Repair Manual I...jiuliu14811471
This document provides instructions for removing and installing the cylinder head assembly on a Caterpillar 3304 engine. The steps include draining coolant, removing exhaust manifolds, valve covers, belts, hoses, wires and other components. The cylinder head bolts are then removed to lift off the head. Reinstallation follows the reverse order, applying thread lubricant and torquing bolts to the specified values. Valve clearance is adjusted at the end.
The document provides instructions for removing and installing an exhaust manifold and inlet/exhaust valves on a 3054E industrial engine. It includes removal and installation procedures with required tools and safety notices. The procedures describe removing/installing the exhaust manifold gasket, setscrews, and turbocharger. For valves, it describes removing/installing the valve springs, retainers, keepers, and stem seals while ensuring the piston is at top dead center.
This document provides installation instructions for a fuel injection pump on a 3054C industrial engine. It consists of 14 steps: 1) Ensure the engine is at top dead center, 2) Install an O-ring on the pump, 3) Position and bolt the pump to the housing, 4) Install a bracket, 5) Install the pump gear and tighten, 6) Connect wiring, 7) Connect fuel lines, 8) Adjust a spacer and bolt, 9) Tighten the gear nut, 10) Remove timing tools, 11) Install covers and pulleys, 12) Install fuel lines. The instructions include illustrations and torque specifications for each step.
1. The document provides instructions for assembling and disassembling the piston pump on a 994H Wheel Loader. It describes the required tools and gives step-by-step instructions with accompanying illustrations.
2. The assembly procedure involves installing bearings, seals, springs, pistons, and other components in the proper order. Precise measurements are taken to ensure correct lift-off limitations.
3. The disassembly and installation procedures are described for removing and installing the high pressure screen and piston pump. Hoses and fittings are disconnected and reconnected.
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
The semiochemicals market size has grown rapidly in
recent years. It will grow from $4.56 billion in 2023
to $5.37 billion in 2024 at a compound annual
growth rate (CAGR) of 17.6%. The growth in the
historic period can be attributed to market
acceptance and education, pest resistance concerns,
increased agricultural productivity demands,
chemical ecology research, growing advancements in
formulations. The semiochemicals market size is
expected to see rapid growth in the next few years. It
will grow to $9.67 billion in 2028 at a compound
annual growth rate (CAGR) of 15.9%.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329E EXCAVATOR PTY
Configuration: 329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -KENR8881-05 Publication Date -01/11/2012 Date Updated -10/05/2016
i05909563
Vibration Damper and Pulley - Remove
SMCS - 1205-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M14 x 1.5 by 100 mm
1
B 227-4393 E18 Torx Socket 1
Start By:
A. Remove the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt - Remove
and Install" for the correct procedure.
Note: The weight of the assembly of the crankshaft pulley, the vibration damper, and the
crankshaft adapter is approximately 22 kg (48 lb).
1/3
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g02368017
1. Use a suitable tool in order to prevent the crankshaft from rotating. Use Tooling (B) to
remove one Torx screws (1) from crankshaft pulley assembly (2) .
2. Install Tooling (A) into crankshaft pulley assembly (2) .
3. Remove remaining Torx screws (1) from crankshaft pulley assembly (2) .
4. Remove crankshaft pulley assembly (2) .
5. Tooling (A) .
2/3
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 2 g02368018
6. If necessary, follow Step 6.a through Step 6.b in order to remove friction shim (3) from the
crankshaft.
a. Remove the front seal from the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
b. Remove friction shim (3) .
7. If necessary, follow Step 7.a through Step 7.c in order to disassemble vibration damper,
crankshaft pulley from crankshaft adapter.
a. Place the crankshaft pulley assembly onto a suitable support.
b. Remove bolts (7) from crankshaft pulley assembly (2) .
c. Remove vibration damper (6) and crankshaft pulley (5) from adapter (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri May 1 11:59:48 UTC+0800 2020
3/3
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329E EXCAVATOR PTY
Configuration: 329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -KENR8881-05 Publication Date -01/11/2012 Date Updated -10/05/2016
i05909564
Vibration Damper and Pulley - Install
SMCS - 1205-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M14 x1.5 by 100 mm
1
B 227-4393 E18 Torx Socket 1
C 8T-3052 Degree Wheel 1
D -
Guide Stud
M12 x1.75 by 50 mm
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 1 g02368018
1. Ensure that the crankshaft adapter and the front of the crankshaft are clean and free from
damage.
2. Inspect vibration damper (6) for damage. If necessary, replace the vibration damper.
3. If necessary, follow Step 3.a through Step 3.e in order to install vibration damper,
crankshaft pulley to crankshaft adapter.
a. Place crankshaft adapter (4) onto a suitable support.
b. Install Tooling (D) crankshaft adapter (4) .
c. Install crankshaft pulley (5) and vibration damper (6) over Tooling (D) .
d. Install bolts (7) to the crankshaft pulley assembly.
Note: Evenly space bolts (7) around the crankshaft pulley assembly.
e. Tighten bolts (7) to a torque of 115 N·m (85 lb ft).
4. If necessary, install friction shim (3) . Follow Step 4.a through Step 4.b in order to install
friction shim (3) .
a. Install friction shim (3) .
2/4
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. b. Install a new front seal to the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
5. Install Tooling (A) to the crankshaft.
Illustration 2 g02368017
6. Install crankshaft pulley assembly (2) onto the crankshaft.
7. Install one Torx screws (1) to crankshaft pulley assembly (2) hand tighten.
8. Remove Tooling (A) .
9. Install remaining Torx screws (1) to crankshaft pulley assembly (2) .
10. Use a suitable tool in order to prevent the crankshaft from rotating. Tighten Torx screws (1)
to a torque of 40 N·m (29 lb ft).
11. Use Tooling (B) and Tooling (C) to turn Torx screws (1) through an additional 120 degrees.
End By: Install the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt -
Remove and Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Fri May 1 12:00:44 UTC+0800 2020
3/4
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329E EXCAVATOR PTY
Configuration: 329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -KENR8881-05 Publication Date -01/11/2012 Date Updated -10/05/2016
i05246993
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 367-3534 Oil Seal Removal & Installer Tool 1
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Remove" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 1 g03344801
1. Position Tooling (A) onto crankshaft front seal (2) .
2. Turn Tooling (A) in a counterclockwise direction and remove crankshaft front seal (2) from
front cover (1) .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 367-3534 Oil Seal Removal & Installer Tool 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. 1. Ensure that the front cover is clean and free from damage.
Illustration 2 g03344801
2. Correctly position a new crankshaft front seal (2) in Position (X) onto front cover (1) .
3. Position Tooling (A) onto crankshaft front seal (2) .
4. Use Tooling (A) in order to turn crankshaft front seal (2) in clockwise direction.
5. If a torque greater than 50 N·m (37 lb ft) is necessary, in order to install crankshaft front
seal (2) . Remove crankshaft front seal (2) . Inspect the crankshaft front seal and the front
cover for faults or damage.
6. If necessary repeat Step 2 through Step 5 in order to install crankshaft front seal (2) .
End By: Install the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper
and Pulley - Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri May 1 12:01:40 UTC+0800 2020
3/3
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329E EXCAVATOR PTY
Configuration: 329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -KENR8881-05 Publication Date -01/11/2012 Date Updated -10/05/2016
i03934107
Front Cover - Remove and Install - Heavy Duty Front Cover
SMCS - 1166-010
Removal Procedure
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Remove" for the correct procedure.
b. If the engine is equipped with a fan, remove the fan. Refer to Disassembly and Assembly,
"Fan - Remove and Install" for the correct procedure.
c. Remove the front seal. Refer to Disassembly and Assembly, "Crankshaft Front Seal -
Remove and Install" for the correct procedure.
1/4
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 1 g02048613
1. Remove bolts (3) and bolts (4). Identify the positions of bolts of different length.
2. Remove front cover (1) from the front housing.
3. Remove gasket (2) from front cover (1).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M8 by 70 mm
2
B 364-7210 Front Cover Alignment Tool 1
2/4
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 2 g02190213
1. Ensure that all components are clean and free from damage. Replace any damaged
components.
2. Thoroughly clean the gasket surface of the front housing.
3. Thoroughly clean front cover (1).
4. Install Tooling (A) into Holes (X) in the front housing.
5. Install a new gasket (2) onto Tooling (A).
6. Install front cover (1) onto Tooling (A).
7. Install bolts (3) and bolts (4) finger tight. Ensure that the bolts of different length are
installed in the correct positions.
8. Use Tooling (B) to align the front cover assembly.
3/4
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. 9. Remove Tooling (A) and install remaining bolts (4).
10. Tighten bolts (3) and bolts (4) to a torque of 22 N·m (195 lb in).
11. Remove Tooling (B).
12. Install a new front seal to the front cover. Refer to Disassembly and Assembly, "Crankshaft
Front Seal - Remove and Install" for the correct procedure.
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Install" for the correct procedure.
b. If the engine was equipped with a fan, install the fan. Refer to Disassembly and Assembly,
"Fan - Remove and Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri May 1 12:02:35 UTC+0800 2020
4/4
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329E EXCAVATOR PTY
Configuration: 329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -KENR8881-05 Publication Date -01/11/2012 Date Updated -10/05/2016
i05215788
Front Cover - Remove and Install
SMCS - 1166-010
Removal Procedure
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Remove" for the correct procedure.
B. If the engine is equipped with a fan, remove the fan. Refer to Disassembly and Assembly,
"Fan - Remove and Install" for the correct procedure.
1/4
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 1 g01992013
1. Remove the front seal from the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
2. Remove bolts (3) and bolts (4) . Identify the positions of bolts of different length.
3. Remove front cover (1) from the front housing.
4. Remove gasket (2) from front cover (1) .
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M8 by 70 mm
2
B 367-3535 Front Cover Alignment Tool 1
2/4
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 2 g02190133
1. Thoroughly clean the gasket surface of the front housing.
2. If the original front cover is installed, follow Step 2.a through Step 2.b.
a. Thoroughly clean front cover (1) .
b. Install a new gasket (2) to front cover (1) . Engage Locators (Y) into the holes in the
front cover.
3. Install Tooling (A) into Holes (X) in the front housing.
4. Use Tooling (A) in order to position the front cover assembly onto the front housing.
5. Install bolts (3) and bolts (4) finger tight. Ensure that the bolts of different length are
installed in the correct positions.
3/4
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 6. Install a new front seal to the front cover. Refer to Disassembly and Assembly, "Crankshaft
Front Seal - Remove and Install" for the correct procedure.
7. Use Tooling (B) in order to align the front cover.
8. Remove Tooling (A) and install remaining bolts (4) .
9. Tighten bolts (3) and bolts (4) to a torque of 22 N·m (195 lb in).
10. Remove Tooling (B) from the front cover.
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Install" for the correct procedure.
b. If the engine was equipped with a fan, install the fan. Refer to Disassembly and Assembly,
"Fan - Remove and Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri May 1 12:03:31 UTC+0800 2020
4/4
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329E EXCAVATOR PTY
Configuration: 329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -KENR8881-05 Publication Date -01/11/2012 Date Updated -10/05/2016
i03934125
Gear Group (Front) - Remove and Install - Heavy Duty Gear
Group (Front)
SMCS - 1206-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 364-9107 Fuel Injection Pump Timing Pin 1
D
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
Start By:
a. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure.
b. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install" for the correct procedure.
1/21
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable. Care must be taken in
order to ensure that the fuel injection pump timing is not lost during the removal of the front gear
group. Carefully follow the procedure in order to remove the gear group.
1. If the air compressor is equipped with a hydraulic pump, remove the hydraulic pump. Refer
to Original Equipment Manufactures (OEM) for the correct procedure.
2. If the engine is equipped, with an air compressor remove the air compressor. Refer to
Disassembly and Assembly, "Air Compressor - Remove" for the correct procedure.
3. If the engine is equipped with only a hydraulic pump, remove the hydraulic pump. Refer to
the OEM for the correct procedure.
4. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure.
Note: Do not use excessive force to install Tooling (D). Do not use Tooling (D) to hold the
crankshaft during repairs.
2/21
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 1 g02048654
5. Remove plug (2) from the cylinder block. Remove O-ring seal (1) from the plug.
6. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure. Install Tooling (D)
through Hole (W) in order to lock the crankshaft.
7. Remove Tooling (D).
8. Use Tooling (A) in order to rotate the crankshaft in a clockwise direction and position the
crankshaft at 60 degrees after top dead center.
3/21
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 2 g02048655
9. Loosen threaded inserts (4) on all rocker arms (3). Unscrew threaded inserts (4) on all
rocker arms (3) until all valves are fully closed. Ensure that guides (5) for the pushrods are
left in position on threaded inserts (4).
Note: Ensure that ALL threaded inserts are fully unscrewed.
10. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure. Install Tooling (D)
through Hole (W) in order to lock the crankshaft. Refer to Illustration 1.
4/21
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 3 g02048653
11. Install Tooling (B) through Hole (X) in camshaft gear (6) into the front housing. Use
Tooling (B) in order to lock the camshaft in the correct position. Refer to System Operation,
Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct
procedure.
12. Use Tooling (C) in order to lock the fuel injection pump gear in the correct position. Refer
to Disassembly and Assembly, "Fuel Injection Pump - Remove" for the correct procedure.
Note: The fuel injection pump must remain locked until the procedure instructs you to
unlock the fuel injection pump.
5/21
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 4 g02052394
13. If the right-hand side of the engine is equipped, with a hydraulic pump remove the hydraulic
pump. Refer to the OEM for the correct procedure.
14. If necessary, remove bolts (7) from plate (8). Remove plate (8) and remove O-ring seal (9).
15. Remove circlip (10) and remove gear assembly (11) from front housing (12).
6/21
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 5 g02053673
16. If necessary, follow Step 16.a through Step 16.b in order to disassemble gear assembly (11).
a. Remove circlip (13) from gear (15).
b. Place gear assembly (11) on a suitable support. Press bearing (14) from gear (15).
7/21
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Illustration 6 g02048714
17. Mark gear (6), gear (16), gear (17) and gear (18) in order to show alignment. Refer to
Illustration 6.
Note: Identification will ensure that the gears can be installed in the original alignment.
18. Remove camshaft gear (6). Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install" for the correct procedure.
8/21
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
28. Illustration 7 g02053984
19. Remove bolts (22) and bolts (24).
20. Remove tube assembly (23) from idler gear (16) and idler gear (26).
21. Remove plate (21).
22. Remove idler gear (16) from front housing (12).
23. Remove idler gear (26) and idler gear hub (25) from front housing (12).
24. Remove hub (20) (not shown) from front housing (12).
25. If necessary, remove bearing (19) from front housing (12). Refer to Disassembly and
Assembly, "Housing (Front) - Remove" for the correct procedure.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
9U-7336 Housing 1
9/21
329E & 329E L Excavators PTY00001-UP (MACHINE) POWERED BY C7.1 Engine...
2020/5/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...