UltraScreen can monitor extrusion quality by measuring insulation layer thickness variation longitudinally, circumferentially, and through frequency analysis. It identifies two mechanisms causing oscillations in thickness around 15-20 seconds and 3 seconds periodically. This diagnostic information can help pinpoint unstable parts of the extruder head and improve extrusion mechanisms. UltraScreen is uniquely suited for this analysis through its rapid 16ms sampling of each of its 16 channels around the cable.

1. CASE STUDY
EXTRUSION QUALITY MONITORING

2. Background
One area in which particular interest has been shown by cable makers is the issue
of monitoring the quality of the extrusion process - in particular the monitoring of
the overall stability of the extrusion of the insulation layer. Now as UltraScreen
samples each of its 16 channels every 16ms, it collects dimensional data that is
ideally suited to addressing such extrusion quality issues. UltraScreen actually
collects such data in data files that hold about 1500 samples per channel and thus
equates to about 25s of run time, or about 40cm of cable length (at 1m/min line
speed).
Longitudinal Thickness Variation
The longitudinal variation in the thickness can be evaluated from this data, and the
figure below presents the insulation layer thickness captured for one channel from
one such data file, actually presented as the variation of this layer thickness
around the average thickness for that file.
How UltraScreen can automatically detect insulation
thickness variations
From figure 1 above it can be seen that thickness varies by about +/ - 300micron
over this length of cable, and this variation can be characterised by evaluating its
Standard Deviation (S.D.) which equates to 118 micron for this channel.

3. A new way to assess
the quality of extrusion
Circumferential Thickness Variation
Now as UltraScreen measures 16 such channels, the S.D. of the extrusion variation
for each channel can be evaluated and displayed as in the figure below.
Figure 2 — Insulation Thickness S.D. values around the cable.
From this figure it is clear that that the extrusion quality of the insulation layer is not consistent
around the cable, with the minimum S.D being measured at about 60micron, whilst the maximum
is about 120micron. Also it is clear that this variation in S.D. value is not random, but has a clear
pattern indicating, in this case, that the cable sector, spanned by channels 5 – 7, has an
extrusion stability that is worse than any other sector.
This sector can be related back to the actual geometry of the
extruder head to identify the aspect of the extruder head that is
responsible for the decrease in extrusion stability.

4. Using Fourier Transforms to identify the
frequency of variation
Frequency Analysis
The time series shown in Fig 1 can be analysed, using Fourier Transform (FT), to identify the
frequency characteristics of this extrusion variation, and the analysis of the data set is presented
in Fig 3. This shows the frequency characteristics of the data in the frequency band up to 4Hz,
with this data scaled to accurately reflect the 16ms sampling period fundamental to the
UltraScreen time series data collection.
Fig 3 - Insulation Layer Thickness Variation, Frequency Analysis (0 – 4Hz)
From Fig 3 it may be seen that there is a large peak (blue arrow) in this data, at the left hand side (low frequency
end) of the FT ‘Spectrum’ presented in the figure. The frequency of this peak is at ~=80mHz which implies a
Periodic Time (PT) for this oscillation of ~12.5s, but as there is also quite a large response also at ~= 40mHz, this
FT response suggests that the ‘mechanism’ producing this oscillation in the layer extrusion probably has a PT a
bit longer than this, so probably more like ~15 - 20s.

5. Identifying the causes of variation
Summary
This note has explored the potential use of UltraScreen to monitor the quality of the
extrusion process, by providing quantitative measures and displays of data
covering:
 Longitudinal layer width variation.
 Circumferential layer width variation.
 Frequency analysis
The feedback provided by this information has the potential to not only identify the
sector of the extruder head responsible for increased extrusion instabilities, but
also the frequency characteristics - and hence the nature - of the extrusion
mechanisms causing the instabilities.
All of this processing is only possible because of the rapid sampling regime
executed uniquely by UltraScreen. This underpins the detailed assessment of both
the physical and the frequency characteristics of the layer extrusions presented in
this case study.
Also, there would seem to be a second peak (red arrow) with a peak frequency ~=330mHz, PT ~
3s. This again would suggest the presence of a second mechanism that is producing an oscilla-
tion in the extruded layer width with a shorter periodic time.
So the analysis of this data set suggests that there are two mechanisms producing oscillations in
the insulation layer thickness.
A lower frequency mechanism, PT ~= 15 - 20s.
A higher frequency mechanism, PT ~= 3s.
Thus such frequency analysis opens up the possibility of using such analysis as a ‘diagnostic’
process that identifies the frequency characteristic of the mechanisms within the extrusion
process responsible for the instability seen in the layer extrusions. With this new knowledge this
potentially allows the mechanisms themselves to be identified and improved.

6. TECHNOLOGY- BASIC PRINCIPLES
LEFT :
16 channels are shown in 2D
format which represents the
total 360 degree view of the
cable under evaluation
Single channel representation
BELOW: Energy from the transducer is
transmitted to the cable via the water. Energy is
reflected back to each single transmitter /
receiver at every boundary where the acoustic
impedance is not matched.
A RING OF 16 ACOUSTIC TRANSDUCERS
SURROUNDS THE CABLE AS IT PASSES
SLOWLY THROUGH A WATER TANK
INSIDE ULTRASCREEN.
Cable is scanned through 360 degrees
every 16mS. This equates to a full scan of
cable parameters and features every 250
microns (at 1 m / minute typical line
speed).