This thesis analyzes the performance of a steam jet ejector chiller solar cooling system installed at Hochschule Karlsruhe during the summer of 2015. Key findings include:
1) The system operated reliably on days with temperatures under 32°C and provided the desired building cooling, though average cooling capacity was lower than the chiller's nominal rating.
2) Data analysis software was developed to evaluate seasonal performance indicators like collectors' yield, utilization factor, and COP values.
3) Over the summer, 25 operative days provided a total of 3,951 kWh of useful cooling while consuming 1,226 kWh of electricity. Thermal and electrical COP were 0.36 and 3.22 respectively
COMPARATIVE STUDY OF DIFFERENT COMBINED CYCLE POWER PLANT SCHEMESijmech
Combined Cycle Power Plants (CCPPs) are imperative for power generation with the capability for
deciphering power shortage during peak and off peak hours. To perk up the recital of the plant, foremost
locations of exergy losses are to be identified and analyzed. In the present work, exergetic analysis of a
CCPP is carried out using the computer programming tool Engineering Equation Solver (EES). The effects
of overall pressure ratio and turbine inlet temperature on the exergy destruction in the CPR are
investigated. The results obtained are compared with that of simple gas turbine cycle power plant. During
real time operation of CCPP exergy destruction in different components is associated with change in
overall pressure ratio and turbine inlet temperature (TIT). Out of the total exergy destruction in the cycle it
is the combustion chamber (CC) which is responsible for the maximum exergy destruction. Nearly 60% of
the total exergy is destroyed in CC. Results clearly show that with increase in complicacy of the power
plant structure, irreversibility of the processes can be improved.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
An approach to reduce cooling water consumption in thermal power plant by vap...dbpublications
Low water levels in feeder canals of thermal power plants causes shut down of power generations for a few days in the last few years. Apart from that the „Central Electricity Authority‟ produced a report on minimizing the overall water requirement of coal based thermal power stations, and as the report tells that a major proportion of the total water requirement of the power stations is the cooling water used.In this paper we made an attempt to perform a thermodynamic study and analysis of a 250 MW thermal power plant, to reduce the mass flow of cooling water by decreasing its temperature with the help of solar powered refrigeration system. So, here we are going to study an analytical mathematical model of a vapor absorption refrigeration system, and we will try to optimize it‟s control parameters using Taguchi L9 orthogonal array. where the cooling water coming from the cooling tower enters into a solar refrigeration system before entering to the condenser of the power plant. , and we will try to optimize it‟s control parameters using Taguchi L9 orthogonal array. As the temperature of the cooling water drops down because of the refrigeration system, the overall requirement of cooling water reduces. A mathematical model of amount of cooling water flow per second is made in this paper using Taguchi analysis.
Review on Design and Theoretical Model of Thermoelectricijsrd.com
This paper presents the theoretical development of the equations that allow to evaluate the performance of an air conditioning system based on the thermoelectric effect. The cooling system is based on a phenomena discovered by Jean Charles Athanase Peltier, in 1834. According to this when electricity runs through a junction between two semiconductors with different properties, heat is dissipated or absorbed. Thus, thermoelectric modules are made by semiconductors materials sealed between two plates through which a continuous current flows and keeps one plate hot and the other cold. The most important parameters to evaluate the performance of the device thermoelectric refrigeration are the coefficient of performance, the heat pumping rate and the maximum temperature difference between the hot side and the cold side of the thermoelectric module.
COMPARATIVE STUDY OF DIFFERENT COMBINED CYCLE POWER PLANT SCHEMESijmech
Combined Cycle Power Plants (CCPPs) are imperative for power generation with the capability for
deciphering power shortage during peak and off peak hours. To perk up the recital of the plant, foremost
locations of exergy losses are to be identified and analyzed. In the present work, exergetic analysis of a
CCPP is carried out using the computer programming tool Engineering Equation Solver (EES). The effects
of overall pressure ratio and turbine inlet temperature on the exergy destruction in the CPR are
investigated. The results obtained are compared with that of simple gas turbine cycle power plant. During
real time operation of CCPP exergy destruction in different components is associated with change in
overall pressure ratio and turbine inlet temperature (TIT). Out of the total exergy destruction in the cycle it
is the combustion chamber (CC) which is responsible for the maximum exergy destruction. Nearly 60% of
the total exergy is destroyed in CC. Results clearly show that with increase in complicacy of the power
plant structure, irreversibility of the processes can be improved.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
An approach to reduce cooling water consumption in thermal power plant by vap...dbpublications
Low water levels in feeder canals of thermal power plants causes shut down of power generations for a few days in the last few years. Apart from that the „Central Electricity Authority‟ produced a report on minimizing the overall water requirement of coal based thermal power stations, and as the report tells that a major proportion of the total water requirement of the power stations is the cooling water used.In this paper we made an attempt to perform a thermodynamic study and analysis of a 250 MW thermal power plant, to reduce the mass flow of cooling water by decreasing its temperature with the help of solar powered refrigeration system. So, here we are going to study an analytical mathematical model of a vapor absorption refrigeration system, and we will try to optimize it‟s control parameters using Taguchi L9 orthogonal array. where the cooling water coming from the cooling tower enters into a solar refrigeration system before entering to the condenser of the power plant. , and we will try to optimize it‟s control parameters using Taguchi L9 orthogonal array. As the temperature of the cooling water drops down because of the refrigeration system, the overall requirement of cooling water reduces. A mathematical model of amount of cooling water flow per second is made in this paper using Taguchi analysis.
Review on Design and Theoretical Model of Thermoelectricijsrd.com
This paper presents the theoretical development of the equations that allow to evaluate the performance of an air conditioning system based on the thermoelectric effect. The cooling system is based on a phenomena discovered by Jean Charles Athanase Peltier, in 1834. According to this when electricity runs through a junction between two semiconductors with different properties, heat is dissipated or absorbed. Thus, thermoelectric modules are made by semiconductors materials sealed between two plates through which a continuous current flows and keeps one plate hot and the other cold. The most important parameters to evaluate the performance of the device thermoelectric refrigeration are the coefficient of performance, the heat pumping rate and the maximum temperature difference between the hot side and the cold side of the thermoelectric module.
ENERGY SAVINGS IN DOMESTIC REFRIGERATOR USING TWO THERMOELECTRIC MODULES& WAT...ijiert bestjournal
The study deals with hybrid refrigerator that combi nes thermoelectric (TER) and vapor compression refrigeration (VCR) and also entail exp erimental details of combined VCR & TER system. Objective is to configure hybrid refrig erator by introducing two Peltier modules (TER) in domestic refrigerator and to analyze compr essor cycles of conventional refrigerator with TER to increase energy efficiency of vapor com pression cycle. For this comparison of standalone VCR and Hybrid VCR+TER system is carried out. A Peltier module of size 4cm � 4cm � .4cm is introduced in the refrigerator cabinet & t he effect on energy efficiency in terms of trip time of compressor is recorded. The e ffect of Air cooled & Water cooled condenser with TER in different structures is also investigated. It is observed that by introducing thermoelectric effect,energy consumpti on of VCR is reduced by almost 10.92% annually,which accounts for 80 units per year. Thu s ultimately improving COP of the hybrid system with better control on temperature over the total run time.
Analysis of Process Parameters to Improve Power Plant EfficiencyIOSRJMCE
This research paper analyses the operational parameters of a thermal power plant to improve effectively & efficient running of the machine while ensuring a degree of compliance with statutory regulations. This study aims to identify the operational gaps associated with running operational parameter in power plant process. It is focused to detect a different thermodynamic variable involved, being multivariate and automatic. For variation of each one of this operational parameters, performance calculations are find out to configure a database of energy variation. The variable data sets now can be used as assessment criteria based on detecting deviations from a reference system that has been updated during plant-performance tests. Although the most important outcome is the highly precise and valuable information that will be obtained on the live operating mode, leading to a head improvements in the cycle efficiency and achieved in the overall control system of the thermal plant. The main aim is to detect any abnormality, reacting as quickly as possible to return the plant to a normal operation mode at best efficient manner.
Investigating The Performance of A Steam Power PlantIJMERJOURNAL
ABSTRACT: The performance analysis of Shobra El-Khima power plant in Cairo, Egypt is presented based on energy and exergy analysis to determine the causes , the sites with high exergy destruction , losses and the possibilities of improving the plant performance. The performance of the plant was evaluated at different loads (Full, 75% and, 50 %). The calculated thermal efficiency based on the heat added to the steam was found to be 41.9 %, 41.7 %, 43.9% , while the exergetic efficiency of the power cycle was found to be 44.8%, 45.5% and 48.8% at max, 75% and, 50 % load respectively. The condenser was found to have the largest energy losses where (54.3%, 55.1% and 56.3% at max, 75% and, 50 % load respectively) of the added energy to the steam is lost to the environment. The maximum exergy destruction was found to be in the turbine where the percentage of the exergy destruction was found to be (42%, 59% and 46.1% at max, 75% and, 50 % load respectively). The pump was found to have the minimum exergy destruction. It was also found that the exergy destruction in feed water heaters and in the condenser together represents the maximum exergy destruction in the plant (about 52%). This means that the irreversibilities in the heat transfer devices in the plant have a significant role on the exergy destruction. So, it is thought that the improvement in the power plant will be limited due to the heat transfer devices.
Scope of Improving Energy Utilization in Coal Based Co-Generation on Thermal ...IJMER
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
Coursework material provides the technical performance analysis of compression, stoichiometric combustion (carbon, hydrogen, sulfur, coal, oil and gas) and expansion.
A study on the edm of al7075+3 wt%sic+3wt% b4c hybrid mmceSAT Journals
Abstract The objective of the project is to investigate the effect of current, pulse on time and pulse off time. For the proposed work Material removal rate (MRR) and Tool wear rate (TWR) were chosen as responses and Current, Pulse on time and pulse off time were chosen as process parameters. Hybrid Aluminium Silicon Carbide (Al 7075 + 3wt. % of SiCp+ 3wt. % of B4C) is used as work material and copper is used as tool material. Design of experiment technique is employed for the experimentation. The mathematical models are prepared by Response Surface Methodology (RSM) technique and Box Behnken Design (BBD) is selected to design the matrix for different combination of process parameters. After completion of the experiments analysis was done using analysis of variance (ANOVA) for 90% confidence level. Keywords: Current, Pulse on time, Pulse off time, Material removal rate (MRR), Tool wear rate (TWR), Design of experiments (DOE), Response surface methodology (RSM), Box-Behken design (BBD), Analysis of variance (ANOVA).
Welcome to International Journal of Engineering Research and Development (IJERD)IJERD Editor
journal publishing, how to publish research paper, Call For research paper, international journal, publishing a paper, IJERD, journal of science and technology, how to get a research paper published, publishing a paper, publishing of journal, publishing of research paper, reserach and review articles, IJERD Journal, How to publish your research paper, publish research paper, open access engineering journal, Engineering journal, Mathemetics journal, Physics journal, Chemistry journal, Computer Engineering, Computer Science journal, how to submit your paper, peer reviw journal, indexed journal, reserach and review articles, engineering journal, www.ijerd.com, research journals,
yahoo journals, bing journals, International Journal of Engineering Research and Development, google journals, hard copy of journal
A Study on Energy Audit of a Cold StorageIJERA Editor
Energy consumption of a cold storage was measured for different storage temperatures. Suction temperature and pressure temperature of the compressor and working time of the compressor were determined to reach evaporator set up temperatures. An axial fan located back of the evaporator was used to distribute the cooled air into the cold store. An electrical heater was used to defrost. The compressor suction temperatures and discharge temperatures varied between 1.80 C - 070 C and 270 C - 350 C respectively. Condenser output temperature is varies 40 C - 100 C. Compressor suction pressure (p1) = 3.5 Kg/cm2 and discharge pressure (p2) = 10.5 Kg/cm2.
ENERGY SAVINGS IN DOMESTIC REFRIGERATOR USING TWO THERMOELECTRIC MODULES& WAT...ijiert bestjournal
The study deals with hybrid refrigerator that combi nes thermoelectric (TER) and vapor compression refrigeration (VCR) and also entail exp erimental details of combined VCR & TER system. Objective is to configure hybrid refrig erator by introducing two Peltier modules (TER) in domestic refrigerator and to analyze compr essor cycles of conventional refrigerator with TER to increase energy efficiency of vapor com pression cycle. For this comparison of standalone VCR and Hybrid VCR+TER system is carried out. A Peltier module of size 4cm � 4cm � .4cm is introduced in the refrigerator cabinet & t he effect on energy efficiency in terms of trip time of compressor is recorded. The e ffect of Air cooled & Water cooled condenser with TER in different structures is also investigated. It is observed that by introducing thermoelectric effect,energy consumpti on of VCR is reduced by almost 10.92% annually,which accounts for 80 units per year. Thu s ultimately improving COP of the hybrid system with better control on temperature over the total run time.
Analysis of Process Parameters to Improve Power Plant EfficiencyIOSRJMCE
This research paper analyses the operational parameters of a thermal power plant to improve effectively & efficient running of the machine while ensuring a degree of compliance with statutory regulations. This study aims to identify the operational gaps associated with running operational parameter in power plant process. It is focused to detect a different thermodynamic variable involved, being multivariate and automatic. For variation of each one of this operational parameters, performance calculations are find out to configure a database of energy variation. The variable data sets now can be used as assessment criteria based on detecting deviations from a reference system that has been updated during plant-performance tests. Although the most important outcome is the highly precise and valuable information that will be obtained on the live operating mode, leading to a head improvements in the cycle efficiency and achieved in the overall control system of the thermal plant. The main aim is to detect any abnormality, reacting as quickly as possible to return the plant to a normal operation mode at best efficient manner.
Investigating The Performance of A Steam Power PlantIJMERJOURNAL
ABSTRACT: The performance analysis of Shobra El-Khima power plant in Cairo, Egypt is presented based on energy and exergy analysis to determine the causes , the sites with high exergy destruction , losses and the possibilities of improving the plant performance. The performance of the plant was evaluated at different loads (Full, 75% and, 50 %). The calculated thermal efficiency based on the heat added to the steam was found to be 41.9 %, 41.7 %, 43.9% , while the exergetic efficiency of the power cycle was found to be 44.8%, 45.5% and 48.8% at max, 75% and, 50 % load respectively. The condenser was found to have the largest energy losses where (54.3%, 55.1% and 56.3% at max, 75% and, 50 % load respectively) of the added energy to the steam is lost to the environment. The maximum exergy destruction was found to be in the turbine where the percentage of the exergy destruction was found to be (42%, 59% and 46.1% at max, 75% and, 50 % load respectively). The pump was found to have the minimum exergy destruction. It was also found that the exergy destruction in feed water heaters and in the condenser together represents the maximum exergy destruction in the plant (about 52%). This means that the irreversibilities in the heat transfer devices in the plant have a significant role on the exergy destruction. So, it is thought that the improvement in the power plant will be limited due to the heat transfer devices.
Scope of Improving Energy Utilization in Coal Based Co-Generation on Thermal ...IJMER
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
Coursework material provides the technical performance analysis of compression, stoichiometric combustion (carbon, hydrogen, sulfur, coal, oil and gas) and expansion.
A study on the edm of al7075+3 wt%sic+3wt% b4c hybrid mmceSAT Journals
Abstract The objective of the project is to investigate the effect of current, pulse on time and pulse off time. For the proposed work Material removal rate (MRR) and Tool wear rate (TWR) were chosen as responses and Current, Pulse on time and pulse off time were chosen as process parameters. Hybrid Aluminium Silicon Carbide (Al 7075 + 3wt. % of SiCp+ 3wt. % of B4C) is used as work material and copper is used as tool material. Design of experiment technique is employed for the experimentation. The mathematical models are prepared by Response Surface Methodology (RSM) technique and Box Behnken Design (BBD) is selected to design the matrix for different combination of process parameters. After completion of the experiments analysis was done using analysis of variance (ANOVA) for 90% confidence level. Keywords: Current, Pulse on time, Pulse off time, Material removal rate (MRR), Tool wear rate (TWR), Design of experiments (DOE), Response surface methodology (RSM), Box-Behken design (BBD), Analysis of variance (ANOVA).
Welcome to International Journal of Engineering Research and Development (IJERD)IJERD Editor
journal publishing, how to publish research paper, Call For research paper, international journal, publishing a paper, IJERD, journal of science and technology, how to get a research paper published, publishing a paper, publishing of journal, publishing of research paper, reserach and review articles, IJERD Journal, How to publish your research paper, publish research paper, open access engineering journal, Engineering journal, Mathemetics journal, Physics journal, Chemistry journal, Computer Engineering, Computer Science journal, how to submit your paper, peer reviw journal, indexed journal, reserach and review articles, engineering journal, www.ijerd.com, research journals,
yahoo journals, bing journals, International Journal of Engineering Research and Development, google journals, hard copy of journal
A Study on Energy Audit of a Cold StorageIJERA Editor
Energy consumption of a cold storage was measured for different storage temperatures. Suction temperature and pressure temperature of the compressor and working time of the compressor were determined to reach evaporator set up temperatures. An axial fan located back of the evaporator was used to distribute the cooled air into the cold store. An electrical heater was used to defrost. The compressor suction temperatures and discharge temperatures varied between 1.80 C - 070 C and 270 C - 350 C respectively. Condenser output temperature is varies 40 C - 100 C. Compressor suction pressure (p1) = 3.5 Kg/cm2 and discharge pressure (p2) = 10.5 Kg/cm2.
Global socio-economic, demographic and technological forces which HP calls Megatrends will have a sustained and transformative impact on businesses, societies, economies, cultures and our personal lives in unimaginable ways in the years to come.
Interested in learning more about Megatrends? Visit hpmegatrends.com.
Tại sự kiện Meet&Greet #1, anh Đoàn Quang Hưng, chuyên gia UI/UX đã có những chia sẻ rất thú vị về topic "Product design for startup" với người tham gia.
Efficiency Analysis For an Experimentally Set-up Double-Pass V-Corrugated Sol...Aakanksha Dubey
This paper presents the efficiency analysis of an experimental set-up double-pass V-corrugated solar air heater. All
the experimental results were obtained with the developed solar air heater kept at an inclination angle of 23.5
degrees (Latitude Angle of Bhopal, India), facing due south, and using DC fans (for forced convection) with
different air flow rates. The efficiency results, gathered on two consecutive typical Indian peak summer days, are
presented taking into consideration the intermittent availability of sunlight at different times on these days. All the
relevant design aspects of the developed double-pass V-corrugated solar air heater such as the material used for
insulation, construction of the outer enclosure, and the solar air heater assembly, are discussed.
Solar photovoltaic/thermal air collector with mirrors for optimal tiltsIJECEIAES
This work is the result of a study of a photovoltaic/thermal air collector that concentrates solar radiation using two mobile mirrors to enhance electrical and thermal energy. The study is made for the site of Tetouan (Morocco) (longitude=-5°, latitude=35.25°) for a daily variation during typical days in May, June, September, and December, days considered as clear sky. To prove the effectiveness of the mirrors on the production of both electrical and thermal energy by the collector, we compared their electrical and thermal efficiency in two cases, without and with mirrors at the optimal positions. We validate the obtained simulation results by comparing them to the results from experimental studies published in the literature, for which a strong agreement was obtained. The model estimates the solar energy received by the hybrid collector during the day, to optimize the performance of the fixed collector, we have searched for the values of the optimal daily tilt angles of the two mirrors which allowed us to enhance the quantity of incoming solar radiation on the collector. The tilt angles depend on the sun’s elevation angle, the azimuth angle for typical days of the year.
Recent advances in semiconductor technology show the improvement of fabrication on
electronics appliances in terms of performance, power density and even the size. This great achievement
however led to some major problems on thermal and heat distribution of the electronic devices. This
thermal problem could reduce the efficiency and reliability of the electronic devices. In order to minimize
this thermal problem, an optimal cooling techniques need to be applied during the operation. There are
various cooling techniques have been used and one of them is passive pin fin heat sink approach. This
paper focuses on inline pin fin heat sink, which use copper material with different shapes of pin fin and a
constant 5.5W heat sources. The simulation model has been formulated using COMSOL Multiphysics
software to stimulate the pin fin design, study the thermal distribution and the maximum heat profile.
IJREI_A thermodynamic analysis of ejector type vapour refrigeration system us...Husain Mehdi
A thermodynamic analysis on Ejector Refrigeration Cycle (ERC), have been performed using eco-friendly refrigerants (i.e.R-404A, R-410A, R-407C, R-423A, R-500, R-502 and R-507C ) A numerical computation is carried out for finding COP, Second Law Efficiency (ηII) , Refrigeration Effect (RE) and Heat Input (Qin) of the ERC along with the variation in boiler temperature (Tb) , condenser temperature (Tc) and evaporator temperature (Te) for ecofriendly refrigerants for the ranges of the temperatures where the evaporator temperature is varying from 253K to 273K, with varying condenser temperature from 313K to 328K and with varying boiling temperature from 320 K to 345K. The maximum first Law Efficiency (ηI) is found in the range of 1.5-1.8 with fluid R-404A and condenser temperature 328K. At 253K evaporator temperature R-404A is working with maximum Second Law Efficiency (ηII) 37%. For the entire range of boiling temperature R-410A is having maximum Second Law Efficiency (ηII) except at 345K where R-404A is highest. The refrigeration effect is the maximum and is in the range of 200kW to 220kW for R-410A for all the ranges of temperatures. The highest COP is associated with R-404A with temperature variations
Refrigeration and air conditioning (full note)shone john
Principles of refrigeration: Thermodynamics of refrigeration - Carnot cycle,
reversed carnot cycle, heat pump, and refrigerating machine- coefficient of
performance - unit of refrigeration - refrigeration methods- conventional
refrigeration systems. Air refrigeration system- Bell Coleman cycle - C.O.P.
capacity work and refrigerant flow requirements in Bell - Coleman cycle.
Module 2
Vapour compression system: simple cycle -comparison with Carnot cycle -
theoretical, actual and reactive - COP effect of operating parameters on
COP - wet, dry and superheated compression - under cooling - actual cycle
representation on TS and PH diagrams simple problems. Advanced
vapour compression systems - multistage vapour compression systems -
flash chamber multiple compression and evaporation systems cascading -
simple problems.
Module 3
Vapour absorption systems: simple, cycles - actual cycle - ammonia water
and lithium bromide water systems - COP - electrolux system. Refrigerant
and their properties: Nomenclature - suitability of refrigerants for various
applications - unconventional refrigeration methods- Vortex tube, steamjet, magnetic (cryogenics) refrigeration and thermoelectric refrigeration -
applied refrigeration house hold refrigerators - unit air conditioners andModule 4
Refrigeration system components: condensers - water and air cooled
condensers - evaporative condensers - expansion devises - capillary tubeconstant pressure expansion valve - thermostatic expansion valve - float
valve and solenoid valve - evaporators - natural convection coils - flooded
evaporators - direct expansion coils. Reciprocating compressors: single
stage and multistage compressors - work done optimum pressure ratioeffect of interfolding - volumetric efficiency -effect of clearance -
isothermal and adiabatic efficiency - compressed air motors. Rotodynamic
compressors: Screw and vane type compressors - principle of operation -
hermetic, semihermetic and open type refrigeration compressors.
Module 5
Principles of air conditioning: Psychrometry and psychrometric chart
thermodynamics of human comfort - effective temperature - comfort chart
applied psychrometry - sensible heat factor - psychometric processproblems. Winter air conditioning: heating load calculations humidifiers
and humidistat. Summer air conditioning: cooling load calculations - year
round air conditioning - unitary and central systems - principles of air
distribution - design of air duct systems.
References
1. Refrigeration and air conditioning - Ballaney P. L.
2. Refrigeration and air conditioning - Stocker W. F.
3. Refrigeration and air conditioning - Jordan and Protester
4. Principles of Refrigeration - Roy J. Dossat
Numerical Study of Entropy Generation in an Irreversible SolarPowered Absorpt...inventionjournals
The ideal three-heat-reservoir (THR) model for absorption refrigeration cycles is extended to include external and internal irreversibilities. Three empirical functions are used to model the internal entropy generation of the cycle. The parameters of these functions are estimated by fitting data obtained by simulation to the predictions of the THR model. The THR model using a linear function or a logarithmic function for the internal entropy generation is able to reproduce performance data for absorption systems with good accuracy
THERMAL PERFORMANCE AND ECONOMICS ANALYSIS OF DOUBLE FLOW PACKED BED SOLAR AI...IAEME Publication
Solar air heater is a type of heat exchanger that transforms solar radiation energy into heat energy. Conventional solar air heaters have poor thermal performance due to high heat losses and low convective heat transfer coefficient between absorber and flowing air. Attempts have been made to improve the thermal performance of conventional solar air heater by employing various design and flow arrangements. Double flow solar air heater with packing is an important and effective design improvement that has been proposed to improve the thermal performance. This paper presents the performance and economic analysis of double flow solar air collector with and without packing in the duct. Effect of various parameters on the thermal performance and pressure drop characteristics has been studied experimentally. The study concludes that double flow arrangement with packing is economical and having short payback period. Also, the thermal performance of double flow solar air heater with packing in upper duct is significantly higher compared to double flow solar air heater without packing and conventional solar air heater.
EXPERIMENTAL AND NUMERICAL STUDY OF A MICRO-COGENERATION STIRLING ENGINE FOR ...
Carbonare Nicolas - Zusammenfassung MA
1. Analysis of performance and results of a
Steam Jet Ejector Chiller (Solar Cooling)
Master of Science Thesis Summary – MSc. Energy & Environment
Karlsruher Institut für Technologie – Instituto Tecnológico de Buenos Aires
In cooperation with Hochschule Karlsruhe für Technik und Wirtschaft
Author: Nicolás Carbonare (1797915)
Tutors:
Dr. Ferdinand Schmidt (KIT)
Dipl.-Ing Tunay Özcan (HSKA)
Examiners:
Prof. Dr. Ing. Martin Gabi (KIT)
Dra. Ing. Cecilia Smoglie (ITBA)
Prof. Dr. Ing. Michael Kauffeld (HSKA)
Karlsruhe, May 2016
2. 2
1. Introduction
A cooperation between the Hochschule Karlsruhe (HSKA) and private companies developed the
Prosolar DSKM Project, in order to test a potential solar heating and cooling system, based on a
steam jet ejector chiller and driven with 100% renewable energy (only auxiliary electricity). The
project was funded by the Bundesministerium für Bildung und Forschung and companies and
institutes GEA Wiegand, Ritter Solar und Fraunhofer-Institut für Umwelt-, Sicherheits- und
Energietechnik UMSICHT took also part in the project. The aim of this work is to study the
operational results of the facility during its first full summer of operation, on the year 2015. The
results and performance indicators are calculated and the operation is analyzed. A comparison
with similar facilities of different approaches is carried out to benchmark the current situation
of the HSKA Installation and to identify potential future improvement opportunities.
2. Steam Jet Ejector Facility
The system consists of a nominal 82 KW steam jet ejector chiller driven with 360 m2
vacuum tube
solar collectors, and assisted by a wet open cooling tower, in order to air-condition a 3130 m2
building. Hot and cold energy storages were developed in order to serve as an operational buffer.
Figure 1 – Scheme of the SJE facility
The solar heat from the collector is used to produce steam in a steam drum. This later enters the
SJE as the Motive Steam at a relative high pressure (3 bar) and temperature (133°C). Following
Pollerberg (2008) [1] description, “it pumps the vaporous refrigerant from the evaporator into
the condenser against a higher pressure and reduces the pressure in the evaporator (up to 10
mbar). The pressure reduction causes boiling of the remaining liquid water in the evaporator and
1 Pollerberg, Clemens; Ahmed Hamza H. Ali; Dötsch, Christian (2008) – “Solar driven steam jet ejector chiller” - Fraunhofer
Institute for Environmental, Safety and Energy Technology UMSICHT, Oberhausen, Germany and Department of Mechanical
Engineering, Faculty of Engineering, Assiut University, Egypt.
3. 3
generates cold water (around 10°C), which is fed to the convective cooler”. The mixture (motive
and suction mass flows) flows at supersonic speed and enters the condenser (50 mbar, 33°C).
Condensed mixture is cooled at a cooling tower, and after that it flows back to the evaporator
and steam drum respectively. In addition, some of the advantages listed in several studies are
its good partial load behavior (moderate mean COP with solar power) and the possibility to use
water as a refrigerant (manipulated without risks).
3. Software Development
The first step of this study was to understand the measured values of the whole facility during
certain periods of interest. To make this possible, a database with all the measurements of
summer 2015 was created, programmed with Visual Basic (VBA) in Microsoft Excel 2013.
The SPS software of the facility creates .csv files on a daily basis, measuring 152 variables of
different kind. All the files were compiled and processed into a database, to perform several data
analysis and to allow the comparison
between the facilities. Then, the software
was programmed, allowing to perform
different types of analysis, in different
timeframes, with a good time of response.
If someone wants to analyze just one day
for twelve hours, it makes it faster to
firstly perform the timeframe filtering.
One day and twelve hours means 108.000
values of the 32.400.000 of the seasonal
data, lowering the average response time.
It combines fast calculations with
graphics, obtaining all the data necessary
to carry out a complete analysis.
The following Key Performance Indicators were defined to evaluate the seasonal performance.
𝐶𝑜𝑙𝑙𝑒𝑐𝑡𝑜𝑟𝑠′
𝑌𝑖𝑒𝑙𝑑 =
𝐷𝑟𝑖𝑣𝑖𝑛𝑔 𝐻𝑒𝑎𝑡 [𝑘𝑊ℎ]
𝐶𝑜𝑙𝑙𝑒𝑐𝑡𝑜𝑟𝑠´𝐴𝑟𝑒𝑎 [𝑚2]. 𝑦𝑒𝑎𝑟
𝐶𝑜𝑙𝑙𝑒𝑐𝑡𝑜𝑟𝑠′ 𝑈𝑡𝑖𝑙𝑖𝑧𝑎𝑡𝑖𝑜𝑛 𝐹𝑎𝑐𝑡𝑜𝑟 =
𝐷𝑟𝑖𝑣𝑖𝑛𝑔 𝐻𝑒𝑎𝑡 [𝑘𝑊ℎ]/1000
𝑆𝑜𝑙𝑎𝑟 𝑅𝑎𝑑 [
𝑊
𝑚2] ∗ 𝐶𝑜𝑙𝐴𝑟𝑒𝑎 [𝑚2] ∗ 𝐻𝑠[ℎ]
𝐶𝑂𝑃𝑒𝑙 =
𝑈𝑠𝑒𝑓𝑢𝑙 𝐶𝑜𝑙𝑑 [𝑘𝑊ℎ]
𝐸𝑙𝑒𝑐𝑡𝑟𝑖𝑐𝑎𝑙 𝐸𝑛𝑒𝑟𝑔𝑦 [𝑘𝑊ℎ]
𝐶𝑂𝑃𝑡ℎ =
𝑈𝑠𝑒𝑓𝑢𝑙 𝐶𝑜𝑙𝑑 [𝑘𝑊ℎ]
𝐷𝑟𝑖𝑣𝑖𝑛𝑔 𝐻𝑒𝑎𝑡 [𝑘𝑊ℎ]
𝑃𝐸𝑅 =
𝑈𝑠𝑒𝑓𝑢𝑙 𝐶𝑜𝑙𝑑 [𝑘𝑊ℎ]
𝐸𝐸 [𝑘𝑊ℎ] ∗ 𝑃𝐸𝐹𝑒𝑙
𝑃𝐸𝑅 𝑆𝑎𝑣𝑖𝑛𝑔𝑠 = 1 −
𝐸𝐸 [𝑘𝑊ℎ] ∗ 𝐶𝑂𝑃𝑅𝑒𝑓
𝑈𝑠𝑒𝑓𝑢𝑙 𝐶𝑜𝑙𝑑 [𝑘𝑊ℎ]
Figure 2 – Input screen
4. 4
The PEFel and the COPref are defined according to the standards taken in the IEA Task 38a [2] as
2.7 and 2.8 respectively.
Furthermore, the software is programmed in order to filter all the measurement errors by
system failures that were encountered. Frequent errors are stuck values, extremely high
temperatures in certain sensors, negative volume flows and mismatch of variables. Temperature
sensor calibrations and calculations of errors’ propagation in measurements were also
performed, in order to minimize the impact of the failures already mentioned.
4. Analysis of results
After gathering the seasonal results from summer 2015 and taking some particular days as
examples, the analysis was carried out. As a highlight, the considered working days were those
in which the useful cold obtained was above 20 KWh and a registered working time of the
ejectors was at least one hour. The Figure-3 shows the daily registered values previously
mentioned.
Figure 3 – Summary of delivered cold on Summer 2015
After gathering the seasonal results from summer 2015 and taking some particular days as
examples, the analysis was carried out. It should be emphasized that there were only 25
registered working days, with a threshold of 350 KWh of useful cold and 5-hour ejector
operation. A random typical day was picked (31.07.2015) and then analyzed on its full extension.
The Figure-4 shows the cooling operation performance of the picked sample day.
2 Jähnig, Dagmar; Thuer, Alexander (et. Al. 2011) – “D-A3b: Monitoring Results. A technical report of subtask A (Pre-engineered
systems for residential and small commercial applications)”. Austrian Institute of Technology (AIT), Giefinggasse 2, A-1210
Vienna, Austria.
5. 5
Figure 4 – Cooling operation
On this day, in which the ambient temperature overcame 30 °C, a partial load behavior can be
easily identified, taking into account that the power oscillations remain between 40 and 70 KW.
The achieved evaporator temperatures reach the desired value under 10 °C.
The monitoring of the 2015 cooling season showed that the steam jet ejector chiller worked
reliable in the days where ambient temperature was under 32°C, and the desired air-
conditioning of the building LB was given (around 25 °C). The average cooling capacity of the
system laid between 40 KW and 60 KW, which is below the nominal capacity of 82 KW of the SJE
chiller. This part-load operation caused by the low cooling capacity on the building side has a
negative impact on the thermal and electrical COP. It must be taken into account that in the
hottest days (above 32°C average) the cooling performance was poor and the desired building
temperature could not be delivered.
The Figure-5 shows a heat balance of the main components of the facility. As a key factor, the
motive heat is calculated through a heat balance including the cooling tower, the useful cold, the
heat storages and other factors.
Figure 5 – Heat balance
Despite the strong variations on the motive heat, it can be seen that the cooling power is not
strongly affected due to the performance of the heat storage. The latent heat storage is made
6. 6
of 500 Kg of PE-8110, with a latent storage capacity of around 27 KWh. The presence of this
buffer plays an important role, as it assists the variations of the solar collectors’ field, providing
a balance for the motive heat supplied.
Figure-6 shows the relationship between the thermal performance, the condenser temperature
and the motive steam pressure.
Figure 6 – COPth and Motive Steam pressure vs. Condenser temperature
The registered values show that there is a positive slope for motive pressure against condenser
temperature. This shows that this temperature should be kept as low as possible in order to
reduce the steam pressure requirements. Whenever the condenser temperature rises, the
motive steam pressure should be higher in order to produce the cooling effect on the
evaporator. A higher motive heat has a negative impact on the thermal COP of the facility. This
is also reflected in this graphic, as the blue dots represent a slightly negative slope.
Moreover, figure-7 shows the seasonal results for the solar collectors.
Figure 7 – Seasonal collectors’ performance
There is an evident relationship (direct proportion) between the solar radiation and the
collectors’ yield. Utilization factor stayed between 30% and 40% most of the days. Collectors UF
remained between 30 and 40%, expectable as the vacuum tube collectors are the most efficient
available in the market.
7. 7
Figure-8 shows the results for the average electrical energy consumption of the facility.
Figure 8 – Average electrical energy consumption
It can be seen that the main sources of consumption are related to the chiller operation and heat
rejection circuits. When combined, the fan of the cooling tower and the pump of this circuit
represent the main electricity consumption of the facility (38%). Along with condenser,
evaporator and cold water pumps, they represent the 89% of the total consumption.
In first place, taking a deeper look at the cooling circuit and its pumps, they represent together
about 50% of the total electrical consumption over the 2015 summer season. As it has been
already discussed, the control of this pumps results crucial for the electrical energy consumption.
As the speed of the pumps result as a key attribute, it is of utmost importance to provide an
efficient part-load control of the cooling operation, in order to optimize the consumption of the
facility and, therefore, a better result in the primary energy consumption of the facility.
Regarding the cooling circuit, Henning (2014) [3] stated in his work that, for the primary energy
analysis of a cooling facility, the COPel of the cooling tower results critical, as it is a big influence
on the primary energy consumption. He proposes that this value should always be above 20. The
calculation of this COPel is analogous to the proposed in the equation above, but taking the
rejected heat [KWh] and the electrical energy consumption of this circuit [KWh]. The value
obtained for the summer 2015 was 35, showing a good overall electrical performance.
As a summary of the results, the following points can be made
Partial load behavior - Evaporator temperatures below 10 °C obtained
Few operative days (25/109) – long hours of operation not achieved (4.56 h average)
3
Henning, Hans-Martin; Morgenstern, Alexander; Wiemken, Edo (2014) – “Kolloquium Solare Kühlung im Rahmen des BMBF-
Verbundprojekts ProSolarDSKM“ - Fraunhofer ISE Freiburg and Hochschule Karlsruhe, ProSolarDSKM Project, Karlsruhe,
Germany.
8. 8
Condenser temperature key to achieve desired cooling - Days with average ambient temp
> 35 °C presented poor response
4 MWh Useful Cold – 1.2 MWh Electrical Consumption
Tested limits of operation:
The next table summarizes the main figures for the 2015 summer season.
Table 1 – Summary of Summer 2015 results
5. Comparison of facilities
5.1 Absorption facility in Arnstorf
In order to elaborate a standard of comparison for the obtained results in the SJE facility, an
absorption facility (ABS) developed by ZAE Bayern will be taken, as described by Riepl (2012) [4].
The Figure-9 illustrates the set-up of this facility.
4Riepl, Manuel (et. Al. 2012) – “Operational performance results of an innovative solar thermal cooling and heating plant” – ZAE
Bayern – Garching, Germany.
Summary summer 2015 (04.05.15-07.10.15)
Working days 25
Average operation [Hs] 4.56
Total useful cold [KWh] 3951.2
Average cooling power [KW] 34.66
Total motive heat [KWh] 11129.3
Average ambient temperature [°C] 30.8
Average building temperature [°C] 25.3
Total electrical consumption [KWh] 1226.7
Solar radiation [W/m2] 761.7
Total COPth [-] 0.36
Total COPel [-] 3.22
Total PER [-] 1.29
PER savings [%] 19.5
Total rejected heat [KWh] 14794.6
Collectors' yield [KWh/m2*day] 30.91
Collectors' utilization factor [%] 36%
9. 9
Figure 6 – Absorption facility layout. Source: Riepl (2012) [4]
Firstly, it results interesting that it has a nominal cooling power of 90 KW, which is in the same
scale of the SJE facility. It can be driven either by solar power (single-effect) or a gas burner
(double-effect). The achieved solar fraction was as high as 60 %. When single/double effect are
at the same time under operation, it means both solar field and gas burner are used as heat
sources. Figure-10 shows a comparison of operation in two typical taken days (similar ambient
conditions).
Making specific focus just on the single-effect operational mode, it can be identified that the
achieved thermal COP is higher in the ABS facility. Both worked under partial load operations
(50-70 KW), achieving the ABS facility longer operational hours. Nevertheless, it should be
mentioned that, due to the fact of having a gas burner integrated, achieving the cooling
performance is easier. Long operating hours allow to raise considerably the electrical COP, as it
not only increases the fed-in cold, but also lowers the influence of stand-by operation.
Figure 7 – Comparison of typical days. Source: Riepl (2012) [4]
10. 10
As it was seen on the publication of Helm (2013) [5], the solar collectors field of ABS shows a
poorer performance than the SJE. Yet it would be interest to analyze the potential solar
collectors’ efficiency of the SJE facility, when it worked more days than it actually did on the 2015
season.
A key point of comparison,where relies the primary energy consumption, is the electrical energy.
It was identified that the total consumption of pumps represented for ABS 59%, whereas in SJE
it took the 79%. The highest electrical consumption peaks in both cases for the chilled water and
cooling circuit pumps, both between 20 and 24% of the total. The chiller operation consumed
for ABS 44%, while it arouses around 51% for the SJE. The cooling tower fan consumed 18% for
ABS, while it occupied 14% for SJE. In total, the cooling circuit represents 37% for the ABS facility
and 38% for the SJE, with similar results. All in all, it can be seen that the operational mode of
both facilities was in partial load conditions. A good control of this is necessary to avoid excessive
electrical consumption, lowering the efficiencies and primary energy ratios of the solar cooling
facilities.
In addition, it results fundamental to highlight that only on three days under operation the daily
average temperature was above 25°C. For the SJE were registered instantaneous temperatures
of almost 45°C and daily averages above 30°C. The low ambient temperatures allow the ABS
facility to perform considerably well with a dry cooling tower. Besides, the necessity of a high
pressure motive steam for the SJE highlights the task of the cooling tower, as a lower condenser
temperature allows the machine to operate with less motive heat (pressure). In conclusion, the
cooling tower in the SJE facility needs to achieve maximum temperature differences of 20 K,
which are not considered in the ABS heat rejection circuit (as it operates with low temperature
heat sources). Although in the consulted papers there is no data about building temperature, it
is assumed that the desired temperature was achieved, as it is stated that the amount of
delivered cold was enough to claim a good performance. This is another difference with the SJE,
which could not achieve the desired values in the hottest days (above 35°C). Besides, the
absorption facility made possible the development of a very reliable system with a high solar
energy fraction (around 60%).
A summary of the obtained KPI for the ABS facility is then presented:
Seasonal thermal COP higher in ABS (0.65)
Excellent electrical COP in ABS (above 10)
Higher PER (4.35) in ABS with only solar driven mode
5 Helm, Martin; Hagel, Kilian; Hiebler, Stefan; Pfeffer, Werner; Hiebler, Stefan; Schweigler, Christian (2013) - “Schlussbericht:
Solares Heizen- und Kühlen mit Absoprtionskältemaschine und Latentwärmespeicher.” - Bavarian Center for Applied Energy
Research (ZAE Bayern), Garching, Germany.
11. 11
5.2 Other facilities
In this subsection, the results of the analysis for the SJE facility will be compared with figures
provided from the IEA Task 38a (2010) [6], in order to relate its performance to other similar
facilities. The following Figure-11 provides an indicator to standarize the installations considered.
Figure 8 – Collectors’ area and nominal cooling power. Source: IEA Task 38a [6]
Most of the facilities of the comparison are small scale (under 20 KW cooling power) and with
absorption chiller units, with back-up heaters. More details over the facilities can be found on
the mentioned report of IEA Task 38a [6]. The next figure shows the COPth. The red line is the
value achieved by the facility in the HSKA.
Figure 9 Thermal COP. Source: IEA Task 38a [6]
Only one of the twelve compared facilities achieved a lower COPth, showing that this value could
be improved. The next graphic shows the comparison of COPel. It is important to mention that
the COPel is calculated without stand-by operation consumption.
6 Jähnig, Dagmar; Thuer, Alexander (et. Al. 2011) – “D-A3b: Monitoring Results. A technical report of subtask A (Pre-engineered
systems for residential and small commercial applications)”. Austrian Institute of Technology (AIT), Giefinggasse 2, A-1210
Vienna, Austria.
12. 12
Figure 10 - Electrical COP. Source: IEA Task 38a (2010) [6]
On the contrary, the COPel under operation shows fairly good results in comparison with other
facilities. As the electrical consumption in a 100% renewable energy installation is the only
source of primary energy consumption, this indicator results of key importance.
The Primary Energy Savings are obtained comparing the PE consumption of the studied facility
with a reference one. As a reference installation, a 2.8 COP compression chiller was selected,
and back-ups were provided with different facilities (IEA Task 38a [6], pages 50-53). It is
important to mention that the PE savings, as well as the COPel already seen, were calculated
only under operational mode (not considering stand-by consumption). What is more, the
facilities’ savings are calculated throughout a year, including the PE savings added by winter
operation (except Maclas and Zaragoza, which did not count with heating systems). The results
show that the position of the operational savings of the SJE facility is within the average of the
analyzed facilities, showing at least positive savings.
Figure 11 - Primary Energy Savings. Source: IEA Task 38a (2010) [6]
6. Conclusion
A steam jet ejector facility was developed, as a solar cooling prototype. The results of these
project were gathered through the development of a software. Daily and seasonal results were
obtained, and an analysis was performed.
Regarding the operational performance, the cold delivered during the operation days seemed
enough when the instantaneous ambient temperature stayed below very high temperatures
(below 35°C). For the days above 35°C, there was not enough cooling power.
Regarding the technical performance of the facility, the thermal COP showed lower values than
the initially obtained. As a main cause it could be identified that long operational hours could
not be achieved, and it is on these days that the best thermal efficiency was seen. Focusing on
the electrical consumption, the research goal of 10 for the COPel was obtained. About 50 % of
13. 13
the electricity is consumed by the driving chiller pumps and almost additional 40% on the cooling
tower circuit. It was identified that most of the time the facility did not work under nominal
power. This part load control should be specifically optimized in order to avoid too high electrical
consumption on pumps.
Furthermore, taking a closer look at the collectors’ field, the first measure is the regulation of
the fed-in water volume flow, as the current value of seems too high. However, collectors’ yield
during operational days show a good performance, even in partly cloudy days.
Part of the low available cooling power on the hottest days was due to a high condenser
temperature. This means that the cooling tower power was not enough to provide the necessary
cooled water. A separate static analysis of the cooling tower could be recommended in order to
improve this performance.
The results of the operation of the Steam Jet Ejector (SJE) facility show some optimization
potential. However, consulting other similar experiments show that the reachable efficiencies
are low compared to other solar cooling developments, such as absorption and adsorption
facilities.