Pressure Relief Systems
BACKGROUND TO RELIEF SYSTEM DESIGN Vol.1 of 6
The Guide has been written to advise those involved in the design and engineering of pressure relief systems. It takes the user from the initial identification of potential causes of overpressure or under pressure through the process design of relief systems to the detailed mechanical design. "Hazard Studies" and quantitative hazards analysis are not described; these are seen as complementary activities. Typical users of the Guide will use some Parts in detail and others in overview.
Pressure Relief Systems
BACKGROUND TO RELIEF SYSTEM DESIGN Vol.1 of 6
The Guide has been written to advise those involved in the design and engineering of pressure relief systems. It takes the user from the initial identification of potential causes of overpressure or under pressure through the process design of relief systems to the detailed mechanical design. "Hazard Studies" and quantitative hazards analysis are not described; these are seen as complementary activities. Typical users of the Guide will use some Parts in detail and others in overview.
Amine Gas Treating Unit - Best Practices - Troubleshooting Guide Gerard B. Hawkins
Amine Gas Treating Unit Best Practices - Troubleshooting Guide for H2S/CO2 Amine Systems
Contents
Process Capabilities for gas treating process
Typical Amine Treating
Typical Amine System Improvements
Primary Equipment Overview
Inlet Gas Knockout
Absorber
Three Phase Flash Tank
Lean/Rich Heat Exchanger
Regenerator
Filtration
Amine Reclaimer
Operating Difficulties Overview
Foaming
Failure to Meet Gas Specification
Solvent Losses
Corrosion
Typical Amine System Improvements
Degradation of Amines and Alkanolamines during Sour Gas Treating
APPENDIX
Best Practices - Troubleshooting Guide
OPERATION AND TROUBLE SHOOTING IN UREA SYNTHESI SSECTION.pdfPremBaboo4
In M/S. Saipem process the HP loop operation is very typical including HP stripper and Reactor N/C ratio, H/C ratio and conversion of the reactor. The MP loop also very typical in operation point of view in which the level of Medium pressure absorber is fluctuating frequently when plant starts up /shut down or any process disturbances/upset. This article intended how to tackle theses type of problem and the MP absorber level and why the level is so important? Why density variation in startup/shut down or any upset of the process by any reason. Why the level transmitter of MP absorber is showing erratic level? How to prevent CO2 Carryover to ammonia receiver through ammonia condenser. Can we replace the DP type transmitter with radar type in stripper as well as MP absorber?
COURSE LINK:
https://www.chemicalengineeringguy.com/courses/petrochemicals-an-overview/
Introduction:
The course is mainly about the petrochemical industry. Talks about several chemicals and their chemical routes in order to produce in mass scale the demands of the market.
Learn about:
Petorchemical Industry
Difference between Petroleum Refining vs. Petrochemical Industry
Paraffins, Olefins, Napthenes & Aromatics
Market insight (production, consumption, prices)
Two main Petrochemical Processes: Naphtha Steam Cracking and Fluid Catalytic Cracking
The most important grouping in petrochemical products
Petrochemical physical & chemical properties. Chemical structure, naming, uses, production, etc.
Basic Gases in the industry: Ammonia, Syngas, etc…
C1 Cuts: Methane, Formaldehyde, Methanol, Formic Acid, Urea, Chloromethanes etc…
C2 Cuts: Ethane, Acetylene, Ethylene, Ethylene Dichloride, Vinyl Chloride, Ethylene Oxide, Ethanolamines, Ethanol, Acetaldehyde, Acetic Acid, Ethylene Glycols (MEG, DEG, TEG)
C3 Cuts: Propane, Propylene, Propylene Oxide, Isopropanol, Acetone, Acrylonitrile, Propediene, Allyl chloride, Acrylic acid, Propionic Acid, Propionaldehyde, Propylene Glycol
C4 Cuts: Butanes, Butylenes, Butadiene, Butanols, MTBE (Methyl Tert Butyl Ethers)
C5 cuts: Isoprene, Pentanes, Piperylene, Cyclopentadiene, Dicyclopentadiene, Isoamyl, etc…
Aromatics: Benzene, Toluene, Xylenes (BTX), Cumene, Phenol, Ethyl Benzene, Styrene, Pthalic Anhydride, Nitrobenzene, Aniline, Benzoic Acid, Chlorobenzene, etc…
At the end of the course you will feel confident in how the petrochemical industry is established. You will know the most common petrochemicals as well as their distribution, production and importance in daily life. It will help in your future process simulations by knowing the common and economical chemical pathways.
In the plant, ammonia is produced from synthesis gas containing hydrogen and nitrogen in the ratio of approximately 3:1. Besides these components, the synthesis gas contains inert gases such as argon and methane to a limited extent. The source of H2 is demineralized water and the hydrocarbons in the natural gas. The source of N2 is the atmospheric air. The source of CO2 is the hydrocarbons in the natural gas feed. Product ammonia and CO2 is sent to urea plant. The present article intended the description of ammonia plant for natural gas based plants and the possible material balance of some section.
Electric Process Heaters
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 ADVANTAGES OF ELECTRIC HEATERS
4.1 Safety
4.2 Environment
4.3 Location of Equipment
4.4 Low Temperature Applications
4.5 Cross Contamination
4.6 Control
5 DISADVANTAGES OF ELECTRIC HEATERS
6 POTENTIAL APPLICATIONS FOR ELECTRIC
PROCESS HEATERS
7 GENERAL DESIGN AND OPERATING CONSIDERATIONS
8 TYPES OF PROCESS ELECTRIC HEATERS
8.1 Pipeline Immersion Heaters
8.2 Tank Heaters and Boilers
8.3 Indirect (Fluid Bath) Heaters
8.4 Radiant Furnaces
8.5 Induction Heaters
8.6 Hot Block Heaters
9 CONTROL
10 REFERENCES
FIGURES
1 ELECTRIC HEAT EXCHANGER CONSTRUCTION
2 SHEATHED HEATING ELEMENTS
COURSE LINK:
https://www.chemicalengineeringguy.com/courses/petroleum-refining/
COURSE DESCRIPTION:
The main scope of the course is to create strong basis and fundamentals regarding the processes in the Petroleum Refining. We take a look to the Oil&Gas Industry briefly and continue directly with the Refining Process. We then make a focus in each individual unit operation in the refinery.
Learn about:
* Oil& Gas Industry
* Difference between Petroleum Refining vs. Petrochemical Industry
* Overview of the most important operations and products
* Market insight (supply/demand) as well as (production/consumption)
* Several Petroleum Refineries around the World
Unit Operations & Processes
* Refining and Fractionation
* Atmospheric Distillation Column
* Vacuum Distillation
* Hydrotreating (Hydrogenation)
* Blending
* Reforming
* Isomerization
* Alkylation
* Steam Cracking
* Fluid Catalytic Cracking
* Gas Sweetening (Hydrodesulfurization)
* Coking
Components:
* Fuel Gas / Natural Gas
* Liquified Petroleum Gases (LPG)
* Propane, Butane
* Sulfur / Hydrogen Sulfide
* Gasoline / Automotive Gas Oil
* Naphtha Cuts (Light/Heavy)
* Kerosene
* Diesel
* Gasoil
* Lubricants
* Vacuum Residues
* Asphalt
* Coke
NOTE: This course is focused for Process Simulation
At the end of the course you will feel confident in the Petroleum Refining Industry. You will know the most common Process & Unit Operations as well as their distribution, production and importance in daily life.
----
Please show the love! LIKE, SHARE and SUBSCRIBE!
More likes, sharings, suscribers: MORE VIDEOS!
-----
CONTACT ME
Chemical.Engineering.Guy@Gmail.com
www.ChemicalEngineeringGuy.com
http://facebook.com/Chemical.Engineering.Guy
You speak spanish? Visit my spanish channel -www.youtube.com/ChemEngIQA
Determination of Carbon Dioxide, Ethane And Nitrogen in Natural Gas by Gas C...Gerard B. Hawkins
Determination of Carbon Dioxide, Ethane
And Nitrogen in Natural Gas by Gas Chromatography
1 SCOPE AND FIELD OF APPLICATION
This document is a method for the determination of carbon dioxide, ethane and nitrogen in natural gas in the range 0-10% v/v.
2 PRINCIPLE
The gas sample will be injected automatically by a ten port valve onto the poraplot U column. The nitrogen will elute first and be switched to the mole sieve column. The mole sieve column will be isolated and the poraplot column will elute the carbon dioxide and ethane via a restrictor column to the detector. After the elution of the carbon dioxide and ethane the poraplot column will be back flushed. Then the nitrogen will be allowed to elute from the mole sieve column (see figure 1.) ...
This presentation is a brief descriptive procedure of simulating in aspen flare system analyser (otherwise called as flarenet). It gives a step by step instructions to develop a flare network scheme in the simulator
Amine Gas Treating Unit - Best Practices - Troubleshooting Guide Gerard B. Hawkins
Amine Gas Treating Unit Best Practices - Troubleshooting Guide for H2S/CO2 Amine Systems
Contents
Process Capabilities for gas treating process
Typical Amine Treating
Typical Amine System Improvements
Primary Equipment Overview
Inlet Gas Knockout
Absorber
Three Phase Flash Tank
Lean/Rich Heat Exchanger
Regenerator
Filtration
Amine Reclaimer
Operating Difficulties Overview
Foaming
Failure to Meet Gas Specification
Solvent Losses
Corrosion
Typical Amine System Improvements
Degradation of Amines and Alkanolamines during Sour Gas Treating
APPENDIX
Best Practices - Troubleshooting Guide
OPERATION AND TROUBLE SHOOTING IN UREA SYNTHESI SSECTION.pdfPremBaboo4
In M/S. Saipem process the HP loop operation is very typical including HP stripper and Reactor N/C ratio, H/C ratio and conversion of the reactor. The MP loop also very typical in operation point of view in which the level of Medium pressure absorber is fluctuating frequently when plant starts up /shut down or any process disturbances/upset. This article intended how to tackle theses type of problem and the MP absorber level and why the level is so important? Why density variation in startup/shut down or any upset of the process by any reason. Why the level transmitter of MP absorber is showing erratic level? How to prevent CO2 Carryover to ammonia receiver through ammonia condenser. Can we replace the DP type transmitter with radar type in stripper as well as MP absorber?
COURSE LINK:
https://www.chemicalengineeringguy.com/courses/petrochemicals-an-overview/
Introduction:
The course is mainly about the petrochemical industry. Talks about several chemicals and their chemical routes in order to produce in mass scale the demands of the market.
Learn about:
Petorchemical Industry
Difference between Petroleum Refining vs. Petrochemical Industry
Paraffins, Olefins, Napthenes & Aromatics
Market insight (production, consumption, prices)
Two main Petrochemical Processes: Naphtha Steam Cracking and Fluid Catalytic Cracking
The most important grouping in petrochemical products
Petrochemical physical & chemical properties. Chemical structure, naming, uses, production, etc.
Basic Gases in the industry: Ammonia, Syngas, etc…
C1 Cuts: Methane, Formaldehyde, Methanol, Formic Acid, Urea, Chloromethanes etc…
C2 Cuts: Ethane, Acetylene, Ethylene, Ethylene Dichloride, Vinyl Chloride, Ethylene Oxide, Ethanolamines, Ethanol, Acetaldehyde, Acetic Acid, Ethylene Glycols (MEG, DEG, TEG)
C3 Cuts: Propane, Propylene, Propylene Oxide, Isopropanol, Acetone, Acrylonitrile, Propediene, Allyl chloride, Acrylic acid, Propionic Acid, Propionaldehyde, Propylene Glycol
C4 Cuts: Butanes, Butylenes, Butadiene, Butanols, MTBE (Methyl Tert Butyl Ethers)
C5 cuts: Isoprene, Pentanes, Piperylene, Cyclopentadiene, Dicyclopentadiene, Isoamyl, etc…
Aromatics: Benzene, Toluene, Xylenes (BTX), Cumene, Phenol, Ethyl Benzene, Styrene, Pthalic Anhydride, Nitrobenzene, Aniline, Benzoic Acid, Chlorobenzene, etc…
At the end of the course you will feel confident in how the petrochemical industry is established. You will know the most common petrochemicals as well as their distribution, production and importance in daily life. It will help in your future process simulations by knowing the common and economical chemical pathways.
In the plant, ammonia is produced from synthesis gas containing hydrogen and nitrogen in the ratio of approximately 3:1. Besides these components, the synthesis gas contains inert gases such as argon and methane to a limited extent. The source of H2 is demineralized water and the hydrocarbons in the natural gas. The source of N2 is the atmospheric air. The source of CO2 is the hydrocarbons in the natural gas feed. Product ammonia and CO2 is sent to urea plant. The present article intended the description of ammonia plant for natural gas based plants and the possible material balance of some section.
Electric Process Heaters
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
4 ADVANTAGES OF ELECTRIC HEATERS
4.1 Safety
4.2 Environment
4.3 Location of Equipment
4.4 Low Temperature Applications
4.5 Cross Contamination
4.6 Control
5 DISADVANTAGES OF ELECTRIC HEATERS
6 POTENTIAL APPLICATIONS FOR ELECTRIC
PROCESS HEATERS
7 GENERAL DESIGN AND OPERATING CONSIDERATIONS
8 TYPES OF PROCESS ELECTRIC HEATERS
8.1 Pipeline Immersion Heaters
8.2 Tank Heaters and Boilers
8.3 Indirect (Fluid Bath) Heaters
8.4 Radiant Furnaces
8.5 Induction Heaters
8.6 Hot Block Heaters
9 CONTROL
10 REFERENCES
FIGURES
1 ELECTRIC HEAT EXCHANGER CONSTRUCTION
2 SHEATHED HEATING ELEMENTS
COURSE LINK:
https://www.chemicalengineeringguy.com/courses/petroleum-refining/
COURSE DESCRIPTION:
The main scope of the course is to create strong basis and fundamentals regarding the processes in the Petroleum Refining. We take a look to the Oil&Gas Industry briefly and continue directly with the Refining Process. We then make a focus in each individual unit operation in the refinery.
Learn about:
* Oil& Gas Industry
* Difference between Petroleum Refining vs. Petrochemical Industry
* Overview of the most important operations and products
* Market insight (supply/demand) as well as (production/consumption)
* Several Petroleum Refineries around the World
Unit Operations & Processes
* Refining and Fractionation
* Atmospheric Distillation Column
* Vacuum Distillation
* Hydrotreating (Hydrogenation)
* Blending
* Reforming
* Isomerization
* Alkylation
* Steam Cracking
* Fluid Catalytic Cracking
* Gas Sweetening (Hydrodesulfurization)
* Coking
Components:
* Fuel Gas / Natural Gas
* Liquified Petroleum Gases (LPG)
* Propane, Butane
* Sulfur / Hydrogen Sulfide
* Gasoline / Automotive Gas Oil
* Naphtha Cuts (Light/Heavy)
* Kerosene
* Diesel
* Gasoil
* Lubricants
* Vacuum Residues
* Asphalt
* Coke
NOTE: This course is focused for Process Simulation
At the end of the course you will feel confident in the Petroleum Refining Industry. You will know the most common Process & Unit Operations as well as their distribution, production and importance in daily life.
----
Please show the love! LIKE, SHARE and SUBSCRIBE!
More likes, sharings, suscribers: MORE VIDEOS!
-----
CONTACT ME
Chemical.Engineering.Guy@Gmail.com
www.ChemicalEngineeringGuy.com
http://facebook.com/Chemical.Engineering.Guy
You speak spanish? Visit my spanish channel -www.youtube.com/ChemEngIQA
Determination of Carbon Dioxide, Ethane And Nitrogen in Natural Gas by Gas C...Gerard B. Hawkins
Determination of Carbon Dioxide, Ethane
And Nitrogen in Natural Gas by Gas Chromatography
1 SCOPE AND FIELD OF APPLICATION
This document is a method for the determination of carbon dioxide, ethane and nitrogen in natural gas in the range 0-10% v/v.
2 PRINCIPLE
The gas sample will be injected automatically by a ten port valve onto the poraplot U column. The nitrogen will elute first and be switched to the mole sieve column. The mole sieve column will be isolated and the poraplot column will elute the carbon dioxide and ethane via a restrictor column to the detector. After the elution of the carbon dioxide and ethane the poraplot column will be back flushed. Then the nitrogen will be allowed to elute from the mole sieve column (see figure 1.) ...
This presentation is a brief descriptive procedure of simulating in aspen flare system analyser (otherwise called as flarenet). It gives a step by step instructions to develop a flare network scheme in the simulator
Remote sensing and monitoring are changing the mining industry for the better. These are providing innovative solutions to long-standing challenges. Those related to exploration, extraction, and overall environmental management by mining technology companies Odisha. These technologies make use of satellite imaging, aerial photography and sensors to collect data that might be inaccessible or from hazardous locations. With the use of this technology, mining operations are becoming increasingly efficient. Let us gain more insight into the key aspects associated with remote sensing and monitoring when it comes to mining.
India Orthopedic Devices Market: Unlocking Growth Secrets, Trends and Develop...Kumar Satyam
According to TechSci Research report, “India Orthopedic Devices Market -Industry Size, Share, Trends, Competition Forecast & Opportunities, 2030”, the India Orthopedic Devices Market stood at USD 1,280.54 Million in 2024 and is anticipated to grow with a CAGR of 7.84% in the forecast period, 2026-2030F. The India Orthopedic Devices Market is being driven by several factors. The most prominent ones include an increase in the elderly population, who are more prone to orthopedic conditions such as osteoporosis and arthritis. Moreover, the rise in sports injuries and road accidents are also contributing to the demand for orthopedic devices. Advances in technology and the introduction of innovative implants and prosthetics have further propelled the market growth. Additionally, government initiatives aimed at improving healthcare infrastructure and the increasing prevalence of lifestyle diseases have led to an upward trend in orthopedic surgeries, thereby fueling the market demand for these devices.
Explore our most comprehensive guide on lookback analysis at SafePaaS, covering access governance and how it can transform modern ERP audits. Browse now!
Falcon stands out as a top-tier P2P Invoice Discounting platform in India, bridging esteemed blue-chip companies and eager investors. Our goal is to transform the investment landscape in India by establishing a comprehensive destination for borrowers and investors with diverse profiles and needs, all while minimizing risk. What sets Falcon apart is the elimination of intermediaries such as commercial banks and depository institutions, allowing investors to enjoy higher yields.
[Note: This is a partial preview. To download this presentation, visit:
https://www.oeconsulting.com.sg/training-presentations]
Sustainability has become an increasingly critical topic as the world recognizes the need to protect our planet and its resources for future generations. Sustainability means meeting our current needs without compromising the ability of future generations to meet theirs. It involves long-term planning and consideration of the consequences of our actions. The goal is to create strategies that ensure the long-term viability of People, Planet, and Profit.
Leading companies such as Nike, Toyota, and Siemens are prioritizing sustainable innovation in their business models, setting an example for others to follow. In this Sustainability training presentation, you will learn key concepts, principles, and practices of sustainability applicable across industries. This training aims to create awareness and educate employees, senior executives, consultants, and other key stakeholders, including investors, policymakers, and supply chain partners, on the importance and implementation of sustainability.
LEARNING OBJECTIVES
1. Develop a comprehensive understanding of the fundamental principles and concepts that form the foundation of sustainability within corporate environments.
2. Explore the sustainability implementation model, focusing on effective measures and reporting strategies to track and communicate sustainability efforts.
3. Identify and define best practices and critical success factors essential for achieving sustainability goals within organizations.
CONTENTS
1. Introduction and Key Concepts of Sustainability
2. Principles and Practices of Sustainability
3. Measures and Reporting in Sustainability
4. Sustainability Implementation & Best Practices
To download the complete presentation, visit: https://www.oeconsulting.com.sg/training-presentations
3.0 Project 2_ Developing My Brand Identity Kit.pptxtanyjahb
A personal brand exploration presentation summarizes an individual's unique qualities and goals, covering strengths, values, passions, and target audience. It helps individuals understand what makes them stand out, their desired image, and how they aim to achieve it.
Affordable Stationery Printing Services in Jaipur | Navpack n PrintNavpack & Print
Looking for professional printing services in Jaipur? Navpack n Print offers high-quality and affordable stationery printing for all your business needs. Stand out with custom stationery designs and fast turnaround times. Contact us today for a quote!
Improving profitability for small businessBen Wann
In this comprehensive presentation, we will explore strategies and practical tips for enhancing profitability in small businesses. Tailored to meet the unique challenges faced by small enterprises, this session covers various aspects that directly impact the bottom line. Attendees will learn how to optimize operational efficiency, manage expenses, and increase revenue through innovative marketing and customer engagement techniques.
Accpac to QuickBooks Conversion Navigating the Transition with Online Account...PaulBryant58
This article provides a comprehensive guide on how to
effectively manage the convert Accpac to QuickBooks , with a particular focus on utilizing online accounting services to streamline the process.
Buy Verified PayPal Account | Buy Google 5 Star Reviewsusawebmarket
Buy Verified PayPal Account
Looking to buy verified PayPal accounts? Discover 7 expert tips for safely purchasing a verified PayPal account in 2024. Ensure security and reliability for your transactions.
PayPal Services Features-
🟢 Email Access
🟢 Bank Added
🟢 Card Verified
🟢 Full SSN Provided
🟢 Phone Number Access
🟢 Driving License Copy
🟢 Fasted Delivery
Client Satisfaction is Our First priority. Our services is very appropriate to buy. We assume that the first-rate way to purchase our offerings is to order on the website. If you have any worry in our cooperation usually You can order us on Skype or Telegram.
24/7 Hours Reply/Please Contact
usawebmarketEmail: support@usawebmarket.com
Skype: usawebmarket
Telegram: @usawebmarket
WhatsApp: +1(218) 203-5951
USA WEB MARKET is the Best Verified PayPal, Payoneer, Cash App, Skrill, Neteller, Stripe Account and SEO, SMM Service provider.100%Satisfection granted.100% replacement Granted.
RMD24 | Debunking the non-endemic revenue myth Marvin Vacquier Droop | First ...BBPMedia1
Marvin neemt je in deze presentatie mee in de voordelen van non-endemic advertising op retail media netwerken. Hij brengt ook de uitdagingen in beeld die de markt op dit moment heeft op het gebied van retail media voor niet-leveranciers.
Retail media wordt gezien als het nieuwe advertising-medium en ook mediabureaus richten massaal retail media-afdelingen op. Merken die niet in de betreffende winkel liggen staan ook nog niet in de rij om op de retail media netwerken te adverteren. Marvin belicht de uitdagingen die er zijn om echt aansluiting te vinden op die markt van non-endemic advertising.
Personal Brand Statement:
As an Army veteran dedicated to lifelong learning, I bring a disciplined, strategic mindset to my pursuits. I am constantly expanding my knowledge to innovate and lead effectively. My journey is driven by a commitment to excellence, and to make a meaningful impact in the world.
The world of search engine optimization (SEO) is buzzing with discussions after Google confirmed that around 2,500 leaked internal documents related to its Search feature are indeed authentic. The revelation has sparked significant concerns within the SEO community. The leaked documents were initially reported by SEO experts Rand Fishkin and Mike King, igniting widespread analysis and discourse. For More Info:- https://news.arihantwebtech.com/search-disrupted-googles-leaked-documents-rock-the-seo-world/
Search Disrupted Google’s Leaked Documents Rock the SEO World.pdf
Blending or Mixing of Butane and Propane to Make LPG GAS
1. BLENDING OR
MIXING OF
BUTANE AND
PROPANE TO
MAKE LPG GAS.
Propane Butane LPG
BLENDING
LPG:
PROPANE &
BUTANE
Feedstock’s
Used for
Blending LPG.
C3H8
C4H10
LPG
2. Blending and Mixing is the process of Combination of Hydrocarbon Gases
{Butane & Propane} for Production of blend LPG for Specific Applications.
Identification:
Petroleum Gases – Liquefied gas Uses Butane, Propane, LPG.
Uses:
Multi-purpose product with applications including gaseous fuel for domestic,
commercial and industrial uses; Autogas in desired propane : Butane ratio for
higher efficiency , High calorific value fuels , mixtures most economical type.
LPG Blending technique :
Propane and Butane are mixed in a desired ratio in the blending tank and
mixed homogenously with the help of a recirculation pump . Desired
Propane and Butane quantities are measured either by mass with mass flow
meter or by volume with volume flow meters .
* Blending is separated in part also as follow:
1. In-Line Blending:
In-line blending mixing largest components continuously.
It is better works for its functions:
High Quality - Low cost
Excellent Flexibility - Quick Blending
Safety Control System
2. Batch Blending:
Batch Blending Involves measured volume of components sequentially
in tank ,after it mixed and analyzed for blend.
This Blending is Cost Effective for small Capacity tank.
______________________________________________
BNH GAS TANKS
B-23, Mayanagri, Dapodi, Pune- 411012 India
Tel: +91-20-30686720 / 21/ 22 Fax: +91-20-30686723
Email : bnhgastanks@gmail.com Web : www.bnhgastanks.com