BeO Vibrational Transitions.pdf
•
0 likes•6 views
The document calculates the effective force constant of the beryllium oxide (BeO) molecule using its observed vibrational transition wavelength of 6.724 μm. It first calculates the reduced mass of BeO. It then relates the wavelength to the vibrational frequency using standard equations. This allows it to isolate the force constant, which is calculated to be 4.677x1021 eV/m.
Report
Share
Report
Share
Download to read offline
Recommended
Frequency of Revolution.pdf
The document compares the frequency of revolution of an electron to the frequency of photons emitted during transitions from energy level n to n-1 for different values of n. For n=10, both frequencies are approximately 6.6x10^10 Hz. For higher n values like n=100, 1000, and 10,000, the radiation frequency remains the same at 6.6x10^10 Hz, while the revolution frequency decreases with increasing n.
Planck's Constant.pdf
1. When ultraviolet beams of wavelengths 80 nm and 110 nm struck lead, photoelectrons with maximum energies of 11.390 eV and 7.154 eV were produced.
2. Using the Planck constant equation and these values, the Planck constant h was calculated to be 6.63136×10-34 J·s.
3. The work function of lead was also calculated, found to be 4.11 eV for the 80 nm beam and 4.096 eV for the 110 nm beam.
De Broglie Waves.pdf
To resolve objects of different sizes, the required potential difference is:
(a) 12.40 kV for a virus 12 nm in diameter
(b) 104.4 kV for an atom 0.12 nm in diameter
(c) 1.034 MV (1,034,000 V) for a proton 1.2 fm in diameter
The potential difference must be decreased to increase the kinetic energy of electrons and resolve smaller objects by increasing the electron wavelength relative to the object size.
Ch10 simple harmonic motion 25 02 2013
- Chapter 10 discusses simple harmonic motion, elasticity, and materials deformation. It introduces Hooke's law, which states that the restoring force of an ideal spring is proportional to the displacement from equilibrium.
- Simple harmonic motion occurs when the restoring force is proportional to the displacement. The chapter covers oscillation parameters such as period, frequency, amplitude, velocity, and acceleration.
- Elastic potential energy is stored in springs and other elastic materials when they are compressed or stretched from their natural state. The energy is proportional to the square of the displacement.
- All materials deform to some degree under an applied force; their elastic properties depend on factors like the Young's modulus, shear modulus, and bulk modulus. Hooke's law
Transmission and distribution system design
The document analyzes the design of a transmission line to transmit 145 MW of power over 95 km. It calculates the most economical voltage and number of circuits using an empirical formula. For a single circuit, the economical voltage is 220 kV, and for double circuits it is 132 kV. A double circuit 132 kV line is selected after checking technical criteria like surge impedance loading and multiplying factor. Tower geometry, conductor spacing, insulator requirements, and conductor selection are then analyzed in detail for a double circuit 132 kV line. The BEAR conductor is selected based on current carrying capacity and transmission efficiency criteria.
Gravity Dam (numerical problem ) BY SITARAM SAINI
The document discusses the analysis of a gravity dam, including calculating stresses and checking stability, for both an empty reservoir and full reservoir condition. It provides numerical examples of determining vertical stresses, principal stresses, and shear stresses at the toe and heel of the dam. It also shows calculations for checking the stability of the dam against sliding, overturning, tension and sufficient shear resistance.
physics lab manual.pdf
This document describes an experiment to determine the wavelength of a laser using a diffraction grating. It includes the aim, apparatus required, and formulas used. The formula shown relates the wavelength (λ) of light to the diffraction grating spacing (d), the angle of diffraction (θ), and the order of diffraction (n). The experiment involves measuring the diffraction angle and using the known grating spacing to calculate the wavelength of the laser source.
Three Zeeman Componants.pdf
A collection of hydrogen atoms is placed in a 3.50 T magnetic field. Ignoring electron spin, the document calculates the wavelengths of the three normal Zeeman components of the 3d to 2p transition. Using the Bohr magneton and the normal Zeeman effect formula, the wavelengths are calculated to be 656.43 nm, 656.50 nm, and 656.36 nm.
Recommended
Frequency of Revolution.pdf
The document compares the frequency of revolution of an electron to the frequency of photons emitted during transitions from energy level n to n-1 for different values of n. For n=10, both frequencies are approximately 6.6x10^10 Hz. For higher n values like n=100, 1000, and 10,000, the radiation frequency remains the same at 6.6x10^10 Hz, while the revolution frequency decreases with increasing n.
Planck's Constant.pdf
1. When ultraviolet beams of wavelengths 80 nm and 110 nm struck lead, photoelectrons with maximum energies of 11.390 eV and 7.154 eV were produced.
2. Using the Planck constant equation and these values, the Planck constant h was calculated to be 6.63136×10-34 J·s.
3. The work function of lead was also calculated, found to be 4.11 eV for the 80 nm beam and 4.096 eV for the 110 nm beam.
De Broglie Waves.pdf
To resolve objects of different sizes, the required potential difference is:
(a) 12.40 kV for a virus 12 nm in diameter
(b) 104.4 kV for an atom 0.12 nm in diameter
(c) 1.034 MV (1,034,000 V) for a proton 1.2 fm in diameter
The potential difference must be decreased to increase the kinetic energy of electrons and resolve smaller objects by increasing the electron wavelength relative to the object size.
Ch10 simple harmonic motion 25 02 2013
- Chapter 10 discusses simple harmonic motion, elasticity, and materials deformation. It introduces Hooke's law, which states that the restoring force of an ideal spring is proportional to the displacement from equilibrium.
- Simple harmonic motion occurs when the restoring force is proportional to the displacement. The chapter covers oscillation parameters such as period, frequency, amplitude, velocity, and acceleration.
- Elastic potential energy is stored in springs and other elastic materials when they are compressed or stretched from their natural state. The energy is proportional to the square of the displacement.
- All materials deform to some degree under an applied force; their elastic properties depend on factors like the Young's modulus, shear modulus, and bulk modulus. Hooke's law
Transmission and distribution system design
The document analyzes the design of a transmission line to transmit 145 MW of power over 95 km. It calculates the most economical voltage and number of circuits using an empirical formula. For a single circuit, the economical voltage is 220 kV, and for double circuits it is 132 kV. A double circuit 132 kV line is selected after checking technical criteria like surge impedance loading and multiplying factor. Tower geometry, conductor spacing, insulator requirements, and conductor selection are then analyzed in detail for a double circuit 132 kV line. The BEAR conductor is selected based on current carrying capacity and transmission efficiency criteria.
Gravity Dam (numerical problem ) BY SITARAM SAINI
The document discusses the analysis of a gravity dam, including calculating stresses and checking stability, for both an empty reservoir and full reservoir condition. It provides numerical examples of determining vertical stresses, principal stresses, and shear stresses at the toe and heel of the dam. It also shows calculations for checking the stability of the dam against sliding, overturning, tension and sufficient shear resistance.
physics lab manual.pdf
This document describes an experiment to determine the wavelength of a laser using a diffraction grating. It includes the aim, apparatus required, and formulas used. The formula shown relates the wavelength (λ) of light to the diffraction grating spacing (d), the angle of diffraction (θ), and the order of diffraction (n). The experiment involves measuring the diffraction angle and using the known grating spacing to calculate the wavelength of the laser source.
Three Zeeman Componants.pdf
A collection of hydrogen atoms is placed in a 3.50 T magnetic field. Ignoring electron spin, the document calculates the wavelengths of the three normal Zeeman components of the 3d to 2p transition. Using the Bohr magneton and the normal Zeeman effect formula, the wavelengths are calculated to be 656.43 nm, 656.50 nm, and 656.36 nm.
Atoms and nuclei
This document contains questions and answers related to atomic and nuclear physics concepts. Some key points:
- The uppermost energy level in a diagram is n=infinity with E=0, and the lowest is n=1 with E=-13.6eV.
- Transitions in the Balmer series end at the n=2 level.
- Breeder reactors convert fertile material into fissile material.
- MRI stands for magnetic resonance imaging and uses nuclear magnetic resonance principles.
- Several questions provide calculations to determine transition wavelengths, energy levels, radioactive decay rates, and energy released in nuclear reactions.
WavesNotesAnswers.pdf
This document contains solutions to examples related to wave motion. It begins by finding the period and phase speed of a wave given its wavelength or depth, using the dispersion relationship. It then calculates wave properties like height, velocity, energy, and power from pressure sensor readings. Further sections determine wave characteristics in deep water, shallow water, and when a current is present. The document solves for wavelength, period, phase speed and direction in examples involving deep water, shallow water and coastal refraction.
Dev1insulating solid liquid 2
This document summarizes the key points from a homework assignment on insulating materials. It includes two main problems:
1) Computations related to water content and breakdown voltage in transformer insulation materials. The diffusion of water between cellulose paper and insulating oil is analyzed.
2) Analysis of partial discharges in a solid dielectric with two cavities, including derivation of the equivalent circuit model, calculation of cavity capacitances and voltages required to initiate partial discharges.
Dynamics of structures 5th edition chopra solutions manual
Download at: https://goo.gl/bVUnH2
People also search:
dynamics of structures (5th edition) pdf
dynamics of structures chopra 5th edition pdf
dynamics of structures chopra 4th edition pdf
chopra dynamics of structures pdf
dynamics of structures theory and applications to earthquake engineering pdf
dynamics of structures anil k chopra
dynamics of structures chopra 3rd edition pdf
dynamics of structures: theory and applications to earthquake engineering 5th edition
Concreto armado
DISEÑO DE LOSA ALIGERADA, DETALLADO DEL DISEÑO FINAL , VERIFICACION DE LA RESISTENCIA AL CORTE Y DETERMINACION DEL ANCHO EFECTIVO EN VIGAS T
VIBRATIONS AND WAVES TUTORIAL#2
This document contains the worked solutions to 4 questions regarding damped oscillators and forced oscillations.
Question 1 involves finding the damping constant, natural frequency, and oscillation period for a damped oscillator. Question 2 determines the period and natural frequency of a damped block-spring system.
Question 3 provides the equation of motion for an oscillator driven by an external force and calculates the steady-state amplitude and phase lag. Question 4 finds the resonance frequency that produces maximum amplitude and calculates the steady-state displacement for a constant driving force.
SolutionsPlease see answer in bold letters.Note pi = 3.14.docx
Solution
s:
Please see answer in bold letters.
Note pi = 3.1415….
1. The voltage across a 15Ω is as indicated. Find the sinusoidal expression for the current. In addition, sketch the v and i waveform on the same axis.
Note: For the graph of a and b please see attached jpg photo with filename 1ab.jpg and for c and d please see attached photo with filename 1cd.jpg.
a. 15sin20t
v= 15sin20t
By ohms law,
i = v/r
i = 15sin20t / 15
i = sin20t A
Computation of period for graphing:
v= 15sin20t
i = sin20t
w = 20 = 2pi*f
f = 3.183 Hz
Period =1/f = 0.314 seconds
b. 300sin (377t+20)
v = 300sin (377t+20)
i = 300sin (377t+20) /15
i = 20 sin (377t+20) A
Computation of period for graphing:
v = 300sin (377t+20)
i = 20 sin (377t+20)
w = 377 = 2pi*f
f = 60 Hz
Period = 1/60 = 0.017 seconds
shift to the left by:
2pi/0.017 = (20/180*pi)/x
x = 9.44x10-4 seconds
c. 60cos (wt+10)
v = 60cos (wt+10)
i = 60cos (wt+10)/15
i = 4cos (wt+10) A
Computation of period for graphing:
let’s denote the period as w sifted to the left by:
10/180*pi = pi/18
d. -45sin (wt+45)
v = -45sin (wt+45)
i = -45sin (wt+45) / 15
i = -3 sin (wt+45) A
Computation of period for graphing:
let’s denote the period as w sifted to the left by:
45/180 * pi = 1/4*pi
2. Determine the inductive reactance (in ohms) of a 5mH coil for
a. dc
Note at dc, frequency (f) = 0
Formula: XL = 2*pi*fL
XL = 2*pi* (0) (5m)
XL = 0 Ω
b. 60 Hz
Formula: XL = 2*pi*fL
XL = 2 (60) (5m)
XL = 1.885 Ω
c. 4kHz
Formula: XL = 2*pi*fL
XL = = 2*pi* (4k)(5m)
XL = 125.664 Ω
d. 1.2 MHz
Formula: XL = 2*pi*fL
XL = 2*pi* (1.2 M) (5m)
XL = 37.7 kΩ
3. Determine the frequency at which a 10 mH inductance has the following inductive reactance.
a. XL = 10 Ω
Formula: XL = 2*pi*fL
Express in terms in f:
f = XL/2 pi*L
f = 10 / (2pi*10m)
f = 159.155 Hz
b. XL = 4 kΩ
f = XL/2pi*L
f = 4k / (2pi*10m)
f = 63.662 kHz
c. XL = 12 kΩ
f = XL/2piL
f = 12k / (2pi*10m)
f = 190.99 kHz
d. XL = 0.5 kΩ
f = XL/2piL
f = 0.5k / (2pi*10m)
f = 7.958 kHz
4. Determine the frequency at which a 1.3uF capacitor has the following capacitive reactance.
a. 10 Ω
Formula: XC = 1/ (2pifC)
Expressing in terms of f:
f = 1/ (2pi*XC*C)
f = 1/ (2pi*10*1.3u)
f = 12.243 kΩ
b. 1.2 kΩ
f = 1/ (2pi*XC*C)
f = 1/ (2pi*1.2k*1.3u)
f = 102.022 Ω
c. 0.1 Ω
f = 1/ (2pi*XC*C)
f = 1/ (2pi*0.1*1.3u)
f = 1.224 MΩ
d. 2000 Ω
f = 1/ (2pi*XC*C)
f = 1/ (2pi*2000*1.3u)
f = 61.213 Ω
5. For the following pairs of voltage and current, indicate whether the element is a capacitor, an inductor and a capacitor, an inductor, or a resistor and find the value of C, L, or R if insufficient data are given.
a. v = 55 sin (377t + 50)
i = 11 sin (377t -40)
Element is inductor
In this case voltage leads current (ELI) by exactly 90 degrees so that means the circuit is inductive and the element is inductor.
XL = 55/11 = 5 Ω
we know the w=2pif so
w= 377=2pif
f= 60 Hz
To compute for th.
Sample solved questions in fatigue
This document contains 6 sample problems related to statistical analysis of fatigue data:
1) Analysis of cyclic fatigue data including calculating mean, median, standard deviation, and fitting distributions.
2) Analysis of fatigue life data from 8 samples including calculating mean, standard deviation, and fitting distributions.
3) Analysis of fatigue life ranking data including calculating percent median ranks and fitting a Weibull distribution.
4) Estimating fracture toughness with a given confidence level based on test data.
5) Analyzing correlation between fatigue strength and hardness using linear regression.
6) Determining fatigue crack growth threshold from test data using linear regression.
Project work boost converter
The document describes a boost converter project including specifications and component selection. It specifies an input voltage range of 24-30V, output of 60V and 2.5A. Components selected include a MOSFET, diode, ferrite-core inductor with 41 turns, 625uF output capacitor, and 1kΩ 1W snubber resistor with 3.02nF capacitor. Inductor calculations determine a value of 291.764uH is needed with 56m of 0.35mm wire required.
Unit5-KOM
This document contains 10 problems related to kinematics of machinery. The problems involve calculations related to screw jacks, clutches, pulleys, and belt drives. Key parameters given include load, torque, power, speed, diameter, pressure, coefficient of friction, and more. The problems require determining values such as mechanical advantage, efficiency, torque ratio, radius, width, length, and number of plates/collars. Formulas related to kinematics are used to set up and solve the various calculation problems.
12-Examples on Compression Members (Steel Structural Design & Prof. Shehab Mo...
This document provides examples of calculating the factor resistance of steel columns and angles under axial compression loading. It determines the effective area considering local and global buckling effects. It calculates the critical buckling stress and compares it to design tables. For a double angle, it finds the factor resistance is 427 kN. For a W360x134 column with KLx=12m and KLy=6m, it calculates the factor resistance as 2654.6 kN.
PAUL 10.10.doc
The document describes how to calculate the resistivity of copper using classical models. Given the mean free path and mean speed of electrons in copper at 300K, the resistivity is calculated to be 1.23x10-8 Ωm. Using the same model and equations but with temperature of 100K, the resistivity is calculated to be 6.5x10-8 Ωm. The classical model assumes temperature does not affect mean free path but does affect mean electron speed, following Maxwell-Boltzmann distribution, and this causes resistivity to increase with decreasing temperature.
project designa.docx
1. The document describes the specifications and design calculations for a gear box. It includes the input/output speeds and power, gear sizes and ratios, torque and speed calculations, bending stress analysis, and material selection.
2. Stress and wear analyses were performed on each gear to calculate safety factors and select appropriate materials. Grade 3 carburized and hardened steel was chosen for gear 4 to withstand a maximum bending stress of 244,900 psi.
3. Through calculations, the gear box design was determined to safely deliver 16.4 horsepower at 72 rpm output, with an input of 1538 rpm, using gears constructed of materials like grade 2 through-hardened steel to withstand the operating stresses and wear.
Chapter 07 in som
This document contains solutions to problems involving the calculation of shear stresses in beams. It determines shear stresses at specific points of beams by using the shear formula and calculating the shear force resisted by various beam components. The maximum shear stress in several beams is also calculated. Cross-sectional properties like moment of inertia are used. Shear stresses are indicated on volume elements and shear force diagrams are sketched.
Solved problems in waveguides
1. The document discusses different types of waveguides including parallel plate, rectangular, and circular waveguides. It provides information on their modes of propagation, field components, cutoff frequencies, and other related parameters.
2. Formulas are presented for calculating propagation constants, cutoff frequencies, wavelengths, velocities, and impedances for TE and TM waves in various waveguide structures.
3. Examples are worked out demonstrating the application of the formulas to determine parameters for given waveguide geometries and operating frequencies.
Rhodes solutions-ch4
The document provides solutions to several exercises related to slurry transport. For Exercise 4.1, the solution analyzes shear stress and shear rate data for a phosphate slurry and determines it follows a power-law relationship with a flow index of 0.15 and consistency index of 23.4 Ns0.15/m2. Exercise 4.2 verifies an equation for pressure drop in pipe flow of a power-law fluid. Exercise 4.3 similarly verifies an equation incorporating a yield stress. Subsequent exercises provide solutions for pressure drop, slurry concentration, and rheological properties calculations using data given.
ClassExamplesPeriodicMotionWaves.pdf
The document discusses a 0.5 kg object attached to a spring with a constant of 20 N/m oscillating on a frictionless surface. (a) Given an amplitude of 3 cm, the total energy and maximum speed are calculated. (b) The velocity at a displacement of 2 cm is found. (c) The kinetic and potential energies are computed at a given displacement.
psad 1.pdf
This document contains a summary of a refresher course covering various structural analysis problems. It includes 5 situations involving calculating reactions, tensions, stresses, and shear forces for different structures. The document tests understanding through multiple choice questions after explaining the concepts and showing the calculations for each situation. The situations involve analyzing forces on a portable seat, cables supporting a ceiling, stresses on an element using Mohr's circle, forces on a bridge girder under loading, and stresses in a hollow circular signage pole.
Wavelengths & Range of Energies.pdf
The document provides calculations to determine:
(1) The wavelength of an X-ray photon with energy of 10.0 keV is 0.124 nm.
(2) The wavelength of a gamma-ray photon with energy of 1.00 MeV is 1.24 pm.
(3) The range of energies for photons of visible light with wavelengths between 350-700 nm is 1.77-3.5 eV.
Vectors and Tensor Analysis 11-04-2024.doc
The document contains two sections about two individuals, Robert C Wrede and Prasun Kumar Nayak. Robert C Wrede's section is brief and ends after line 8. The section about Prasun Kumar Nayak spans lines 9 through 37 and details a 373 page document he authored that ends on line 36. Both sections conclude with "The End".
Lagrangian & Hamiltonian Mechanics 11-04-2024.doc
This document appears to be a list of names, numbers, and short phrases. It includes the names John Tailor, Akhlaq Hussain, Dieter Strach, Wolfgang Notling, Vladimir Pletser, Fowler, and NIVALDO. Various page numbers are mentioned such as 291/413, 385 Daqaq, 371, 655 Pages, and 8888. Short phrases also appear including "Degree of Freedom", "Generalized Momenta", and "Hamiltonian". The document does not provide much context or narrative to summarize.
More Related Content
Similar to BeO Vibrational Transitions.pdf
Atoms and nuclei
This document contains questions and answers related to atomic and nuclear physics concepts. Some key points:
- The uppermost energy level in a diagram is n=infinity with E=0, and the lowest is n=1 with E=-13.6eV.
- Transitions in the Balmer series end at the n=2 level.
- Breeder reactors convert fertile material into fissile material.
- MRI stands for magnetic resonance imaging and uses nuclear magnetic resonance principles.
- Several questions provide calculations to determine transition wavelengths, energy levels, radioactive decay rates, and energy released in nuclear reactions.
WavesNotesAnswers.pdf
This document contains solutions to examples related to wave motion. It begins by finding the period and phase speed of a wave given its wavelength or depth, using the dispersion relationship. It then calculates wave properties like height, velocity, energy, and power from pressure sensor readings. Further sections determine wave characteristics in deep water, shallow water, and when a current is present. The document solves for wavelength, period, phase speed and direction in examples involving deep water, shallow water and coastal refraction.
Dev1insulating solid liquid 2
This document summarizes the key points from a homework assignment on insulating materials. It includes two main problems:
1) Computations related to water content and breakdown voltage in transformer insulation materials. The diffusion of water between cellulose paper and insulating oil is analyzed.
2) Analysis of partial discharges in a solid dielectric with two cavities, including derivation of the equivalent circuit model, calculation of cavity capacitances and voltages required to initiate partial discharges.
Dynamics of structures 5th edition chopra solutions manual
Download at: https://goo.gl/bVUnH2
People also search:
dynamics of structures (5th edition) pdf
dynamics of structures chopra 5th edition pdf
dynamics of structures chopra 4th edition pdf
chopra dynamics of structures pdf
dynamics of structures theory and applications to earthquake engineering pdf
dynamics of structures anil k chopra
dynamics of structures chopra 3rd edition pdf
dynamics of structures: theory and applications to earthquake engineering 5th edition
Concreto armado
DISEÑO DE LOSA ALIGERADA, DETALLADO DEL DISEÑO FINAL , VERIFICACION DE LA RESISTENCIA AL CORTE Y DETERMINACION DEL ANCHO EFECTIVO EN VIGAS T
VIBRATIONS AND WAVES TUTORIAL#2
This document contains the worked solutions to 4 questions regarding damped oscillators and forced oscillations.
Question 1 involves finding the damping constant, natural frequency, and oscillation period for a damped oscillator. Question 2 determines the period and natural frequency of a damped block-spring system.
Question 3 provides the equation of motion for an oscillator driven by an external force and calculates the steady-state amplitude and phase lag. Question 4 finds the resonance frequency that produces maximum amplitude and calculates the steady-state displacement for a constant driving force.
SolutionsPlease see answer in bold letters.Note pi = 3.14.docx
Solution
s:
Please see answer in bold letters.
Note pi = 3.1415….
1. The voltage across a 15Ω is as indicated. Find the sinusoidal expression for the current. In addition, sketch the v and i waveform on the same axis.
Note: For the graph of a and b please see attached jpg photo with filename 1ab.jpg and for c and d please see attached photo with filename 1cd.jpg.
a. 15sin20t
v= 15sin20t
By ohms law,
i = v/r
i = 15sin20t / 15
i = sin20t A
Computation of period for graphing:
v= 15sin20t
i = sin20t
w = 20 = 2pi*f
f = 3.183 Hz
Period =1/f = 0.314 seconds
b. 300sin (377t+20)
v = 300sin (377t+20)
i = 300sin (377t+20) /15
i = 20 sin (377t+20) A
Computation of period for graphing:
v = 300sin (377t+20)
i = 20 sin (377t+20)
w = 377 = 2pi*f
f = 60 Hz
Period = 1/60 = 0.017 seconds
shift to the left by:
2pi/0.017 = (20/180*pi)/x
x = 9.44x10-4 seconds
c. 60cos (wt+10)
v = 60cos (wt+10)
i = 60cos (wt+10)/15
i = 4cos (wt+10) A
Computation of period for graphing:
let’s denote the period as w sifted to the left by:
10/180*pi = pi/18
d. -45sin (wt+45)
v = -45sin (wt+45)
i = -45sin (wt+45) / 15
i = -3 sin (wt+45) A
Computation of period for graphing:
let’s denote the period as w sifted to the left by:
45/180 * pi = 1/4*pi
2. Determine the inductive reactance (in ohms) of a 5mH coil for
a. dc
Note at dc, frequency (f) = 0
Formula: XL = 2*pi*fL
XL = 2*pi* (0) (5m)
XL = 0 Ω
b. 60 Hz
Formula: XL = 2*pi*fL
XL = 2 (60) (5m)
XL = 1.885 Ω
c. 4kHz
Formula: XL = 2*pi*fL
XL = = 2*pi* (4k)(5m)
XL = 125.664 Ω
d. 1.2 MHz
Formula: XL = 2*pi*fL
XL = 2*pi* (1.2 M) (5m)
XL = 37.7 kΩ
3. Determine the frequency at which a 10 mH inductance has the following inductive reactance.
a. XL = 10 Ω
Formula: XL = 2*pi*fL
Express in terms in f:
f = XL/2 pi*L
f = 10 / (2pi*10m)
f = 159.155 Hz
b. XL = 4 kΩ
f = XL/2pi*L
f = 4k / (2pi*10m)
f = 63.662 kHz
c. XL = 12 kΩ
f = XL/2piL
f = 12k / (2pi*10m)
f = 190.99 kHz
d. XL = 0.5 kΩ
f = XL/2piL
f = 0.5k / (2pi*10m)
f = 7.958 kHz
4. Determine the frequency at which a 1.3uF capacitor has the following capacitive reactance.
a. 10 Ω
Formula: XC = 1/ (2pifC)
Expressing in terms of f:
f = 1/ (2pi*XC*C)
f = 1/ (2pi*10*1.3u)
f = 12.243 kΩ
b. 1.2 kΩ
f = 1/ (2pi*XC*C)
f = 1/ (2pi*1.2k*1.3u)
f = 102.022 Ω
c. 0.1 Ω
f = 1/ (2pi*XC*C)
f = 1/ (2pi*0.1*1.3u)
f = 1.224 MΩ
d. 2000 Ω
f = 1/ (2pi*XC*C)
f = 1/ (2pi*2000*1.3u)
f = 61.213 Ω
5. For the following pairs of voltage and current, indicate whether the element is a capacitor, an inductor and a capacitor, an inductor, or a resistor and find the value of C, L, or R if insufficient data are given.
a. v = 55 sin (377t + 50)
i = 11 sin (377t -40)
Element is inductor
In this case voltage leads current (ELI) by exactly 90 degrees so that means the circuit is inductive and the element is inductor.
XL = 55/11 = 5 Ω
we know the w=2pif so
w= 377=2pif
f= 60 Hz
To compute for th.
Sample solved questions in fatigue
This document contains 6 sample problems related to statistical analysis of fatigue data:
1) Analysis of cyclic fatigue data including calculating mean, median, standard deviation, and fitting distributions.
2) Analysis of fatigue life data from 8 samples including calculating mean, standard deviation, and fitting distributions.
3) Analysis of fatigue life ranking data including calculating percent median ranks and fitting a Weibull distribution.
4) Estimating fracture toughness with a given confidence level based on test data.
5) Analyzing correlation between fatigue strength and hardness using linear regression.
6) Determining fatigue crack growth threshold from test data using linear regression.
Project work boost converter
The document describes a boost converter project including specifications and component selection. It specifies an input voltage range of 24-30V, output of 60V and 2.5A. Components selected include a MOSFET, diode, ferrite-core inductor with 41 turns, 625uF output capacitor, and 1kΩ 1W snubber resistor with 3.02nF capacitor. Inductor calculations determine a value of 291.764uH is needed with 56m of 0.35mm wire required.
Unit5-KOM
This document contains 10 problems related to kinematics of machinery. The problems involve calculations related to screw jacks, clutches, pulleys, and belt drives. Key parameters given include load, torque, power, speed, diameter, pressure, coefficient of friction, and more. The problems require determining values such as mechanical advantage, efficiency, torque ratio, radius, width, length, and number of plates/collars. Formulas related to kinematics are used to set up and solve the various calculation problems.
12-Examples on Compression Members (Steel Structural Design & Prof. Shehab Mo...
This document provides examples of calculating the factor resistance of steel columns and angles under axial compression loading. It determines the effective area considering local and global buckling effects. It calculates the critical buckling stress and compares it to design tables. For a double angle, it finds the factor resistance is 427 kN. For a W360x134 column with KLx=12m and KLy=6m, it calculates the factor resistance as 2654.6 kN.
PAUL 10.10.doc
The document describes how to calculate the resistivity of copper using classical models. Given the mean free path and mean speed of electrons in copper at 300K, the resistivity is calculated to be 1.23x10-8 Ωm. Using the same model and equations but with temperature of 100K, the resistivity is calculated to be 6.5x10-8 Ωm. The classical model assumes temperature does not affect mean free path but does affect mean electron speed, following Maxwell-Boltzmann distribution, and this causes resistivity to increase with decreasing temperature.
project designa.docx
1. The document describes the specifications and design calculations for a gear box. It includes the input/output speeds and power, gear sizes and ratios, torque and speed calculations, bending stress analysis, and material selection.
2. Stress and wear analyses were performed on each gear to calculate safety factors and select appropriate materials. Grade 3 carburized and hardened steel was chosen for gear 4 to withstand a maximum bending stress of 244,900 psi.
3. Through calculations, the gear box design was determined to safely deliver 16.4 horsepower at 72 rpm output, with an input of 1538 rpm, using gears constructed of materials like grade 2 through-hardened steel to withstand the operating stresses and wear.
Chapter 07 in som
This document contains solutions to problems involving the calculation of shear stresses in beams. It determines shear stresses at specific points of beams by using the shear formula and calculating the shear force resisted by various beam components. The maximum shear stress in several beams is also calculated. Cross-sectional properties like moment of inertia are used. Shear stresses are indicated on volume elements and shear force diagrams are sketched.
Solved problems in waveguides
1. The document discusses different types of waveguides including parallel plate, rectangular, and circular waveguides. It provides information on their modes of propagation, field components, cutoff frequencies, and other related parameters.
2. Formulas are presented for calculating propagation constants, cutoff frequencies, wavelengths, velocities, and impedances for TE and TM waves in various waveguide structures.
3. Examples are worked out demonstrating the application of the formulas to determine parameters for given waveguide geometries and operating frequencies.
Rhodes solutions-ch4
The document provides solutions to several exercises related to slurry transport. For Exercise 4.1, the solution analyzes shear stress and shear rate data for a phosphate slurry and determines it follows a power-law relationship with a flow index of 0.15 and consistency index of 23.4 Ns0.15/m2. Exercise 4.2 verifies an equation for pressure drop in pipe flow of a power-law fluid. Exercise 4.3 similarly verifies an equation incorporating a yield stress. Subsequent exercises provide solutions for pressure drop, slurry concentration, and rheological properties calculations using data given.
ClassExamplesPeriodicMotionWaves.pdf
The document discusses a 0.5 kg object attached to a spring with a constant of 20 N/m oscillating on a frictionless surface. (a) Given an amplitude of 3 cm, the total energy and maximum speed are calculated. (b) The velocity at a displacement of 2 cm is found. (c) The kinetic and potential energies are computed at a given displacement.
psad 1.pdf
This document contains a summary of a refresher course covering various structural analysis problems. It includes 5 situations involving calculating reactions, tensions, stresses, and shear forces for different structures. The document tests understanding through multiple choice questions after explaining the concepts and showing the calculations for each situation. The situations involve analyzing forces on a portable seat, cables supporting a ceiling, stresses on an element using Mohr's circle, forces on a bridge girder under loading, and stresses in a hollow circular signage pole.
Wavelengths & Range of Energies.pdf
The document provides calculations to determine:
(1) The wavelength of an X-ray photon with energy of 10.0 keV is 0.124 nm.
(2) The wavelength of a gamma-ray photon with energy of 1.00 MeV is 1.24 pm.
(3) The range of energies for photons of visible light with wavelengths between 350-700 nm is 1.77-3.5 eV.
Similar to BeO Vibrational Transitions.pdf (20)
Dynamics of structures 5th edition chopra solutions manual
Dynamics of structures 5th edition chopra solutions manual
SolutionsPlease see answer in bold letters.Note pi = 3.14.docx
SolutionsPlease see answer in bold letters.Note pi = 3.14.docx
12-Examples on Compression Members (Steel Structural Design & Prof. Shehab Mo...
12-Examples on Compression Members (Steel Structural Design & Prof. Shehab Mo...
More from Rajput Abdul Waheed Bhatti
Vectors and Tensor Analysis 11-04-2024.doc
The document contains two sections about two individuals, Robert C Wrede and Prasun Kumar Nayak. Robert C Wrede's section is brief and ends after line 8. The section about Prasun Kumar Nayak spans lines 9 through 37 and details a 373 page document he authored that ends on line 36. Both sections conclude with "The End".
Lagrangian & Hamiltonian Mechanics 11-04-2024.doc
This document appears to be a list of names, numbers, and short phrases. It includes the names John Tailor, Akhlaq Hussain, Dieter Strach, Wolfgang Notling, Vladimir Pletser, Fowler, and NIVALDO. Various page numbers are mentioned such as 291/413, 385 Daqaq, 371, 655 Pages, and 8888. Short phrases also appear including "Degree of Freedom", "Generalized Momenta", and "Hamiltonian". The document does not provide much context or narrative to summarize.
Work Done By F.doc
1. The document presents the solution to two mechanics problems (Problems 18 and 19) involving calculating displacement (d) and work (W) given position vectors.
2. For Problem 18, d is calculated as 2 units and W is calculated as 26 Nm.
3. For Problem 19, d is calculated as -1 units and W is calculated as 45 Nm.
Visible Light Range.doc
The document summarizes the photon energies of visible light and FM radio frequencies.
(1) The range of photon energies in visible light is from 1.6533 eV to 3.2631 eV.
(2) The energy of a photon from a typical 100 MHz FM radio station broadcast is 4.136×10-15 eV.
TEMP of Blackbody.doc
The document calculates the temperature of a blackbody with a peak spectrum of 700 nm. It uses Wien's displacement law, which relates the peak wavelength to the blackbody temperature. It shows the calculations for peak wavelengths in the visible light region at 700 nm, the microwave region at 3 cm, and the FM radio wave region at 3 m. In each case, it applies Wien's law and solves for the temperature in Kelvin. The temperatures calculated are 29,000 K for 700 nm visible light, 3,000 K for 3 cm microwaves, and 30,000 K for 3 m FM radio waves.
Ratio Fb & Fg.doc
The document describes calculating the ratio of the magnetic force to the gravitational force on a proton moving vertically at the Earth's equator. It gives the proton's speed, the horizontal component of Earth's magnetic field, the proton's mass, and the gravitational acceleration. It then shows the calculations of the magnetic force using the magnetic field and speed, and the gravitational force using mass and gravitational acceleration. The ratio of magnetic to gravitational force is calculated to be approximately 16.
R of Curvature.doc
A beam of particles including protons, electrons, deuterons, and helium atoms all with a speed of 2.5 x 10^8 m/s passes through a magnetic field of 0.40 T perpendicular to their velocity. The radius of curvature of the path is calculated for each particle type using the formula that relates magnetic field, particle mass, charge, and velocity. The radius is found to be 6.52 x 10^-2 m for protons, 3.559 x 10^-1 m for electrons, 1.305 x 10^-1 m for deuterons, and 2.594 x 10^-1 m for helium atoms.
Parallel Vectors.doc
This document provides the solution to a math problem involving vectors. It shows that the vectors (1,3,3), (1,6,6), and (1,-6,-6) are parallel to each other and equal to zero when their dot products are calculated. This means the vectors are linearly dependent and span a line through the origin in three-dimensional space rather than filling out the full three-dimensional space.
JB Marion 8.27.doc
The spacecraft orbits Earth with a speed of 10,160 m/s at a perigee of 6,680 km. Using the law of conservation of angular momentum, the speed of the spacecraft at its apogee of 42,200 km can be calculated. Substituting the given values into the angular momentum equation and solving for the apogee speed gives a value of 1,608.26 m/s.
Gasiorovicz-3.doc
Ultraviolet light with a wavelength of 350 nm was shone on a potassium surface, ejecting photoelectrons with a maximum kinetic energy of 1.6 eV. Using the formula that relates photon energy, work function, and kinetic energy, along with the given values, the work function of potassium was calculated to be 1.94 eV.
Gasiorovicz 4.doc
The document discusses using photoelectric emission data from aluminum to calculate Planck's constant and the work function of aluminum. It provides the maximum kinetic energies of photoelectrons emitted from aluminum when irradiated with 200nm and 258nm wavelength light. It then shows the calculations using Einstein's photoelectric equation to solve for Planck's constant and the work function. Planck's constant is calculated to be 6.626x10-34 Js and the work function of aluminum is calculated to be 3.9 eV.
Fowles Cassiday 4.3.doc
The document discusses determining if a given force field is conservative. It provides two examples of force fields and shows that for a force field to be conservative, the curl of the force must be equal to zero at all points. Additionally, a conservative force field can be written as the gradient of a scalar potential function. For the two example force fields provided, the document calculates the curls and determines that they are equal to zero, showing that the forces are conservative and can be written as gradients of potential functions.
Fowles Cassiday 4.2.doc
The document discusses conservative and non-conservative force fields. It states that a force field is conservative if its curl is zero everywhere, meaning the gradient of a scalar potential field can represent it. Option (a) represents a conservative field, while option (b) is not conservative because its curl is non-zero. Option (c) also represents a conservative field because its curl is equal to zero.
Bright Star.doc
A bright star has an effective surface temperature of 20,000 K. Using Wien's law, the wavelength with maximum emission is 145 nm. This places it in the ultraviolet region of the electromagnetic spectrum, specifically in the far ultraviolet range between 100-200 nm.
Black-Body R.doc
1. The document finds the wavelength of blackbody radiation at temperatures of 3 K, 300 K, and 3000 K using Wien's displacement law.
2. At 3 K the wavelength is calculated to be 966 micrometers.
3. At 300 K the wavelength is calculated to be 9.66 millimeters.
4. At 3000 K the wavelength is calculated to be 966 nanometers.
Area of a Triangle.doc
This document provides the solution to a matrix problem. It involves a 3x3 matrix with entries (1,1,1), (2,3,4), (3,0,1). Several steps of algebraic manipulations are shown to solve for the values of i, j, k, and expressions for X in terms of i, j, k. The final values obtained are i=1, j=3, k=10.
Area of a Triangle 22-25.doc
The document provides solutions to 5 problems that calculate the area of triangles defined by 3D coordinate points. Each problem lists the 3 points that define the triangle, calculates the vectors between the points, finds the cross product of 2 vectors to obtain the area, and states the final area value.
More from Rajput Abdul Waheed Bhatti (20)
Recently uploaded
The History of Stoke Newington Street Names
Presented at the Stoke Newington Literary Festival on 9th June 2024
www.StokeNewingtonHistory.com
BBR 2024 Summer Sessions Interview Training
Qualitative research interview training by Professor Katrina Pritchard and Dr Helen Williams
clinical examination of hip joint (1).pdf
described clinical examination all orthopeadic conditions .
Walmart Business+ and Spark Good for Nonprofits.pdf
"Learn about all the ways Walmart supports nonprofit organizations.
You will hear from Liz Willett, the Head of Nonprofits, and hear about what Walmart is doing to help nonprofits, including Walmart Business and Spark Good. Walmart Business+ is a new offer for nonprofits that offers discounts and also streamlines nonprofits order and expense tracking, saving time and money.
The webinar may also give some examples on how nonprofits can best leverage Walmart Business+.
The event will cover the following::
Walmart Business + (https://business.walmart.com/plus) is a new shopping experience for nonprofits, schools, and local business customers that connects an exclusive online shopping experience to stores. Benefits include free delivery and shipping, a 'Spend Analytics” feature, special discounts, deals and tax-exempt shopping.
Special TechSoup offer for a free 180 days membership, and up to $150 in discounts on eligible orders.
Spark Good (walmart.com/sparkgood) is a charitable platform that enables nonprofits to receive donations directly from customers and associates.
Answers about how you can do more with Walmart!"
Constructing Your Course Container for Effective Communication
Communicating effectively and consistently with students can help them feel at ease during their learning experience and provide the instructor with a communication trail to track the course's progress. This workshop will take you through constructing an engaging course container to facilitate effective communication.
BÀI TẬP DẠY THÊM TIẾNG ANH LỚP 7 CẢ NĂM FRIENDS PLUS SÁCH CHÂN TRỜI SÁNG TẠO ...
BÀI TẬP DẠY THÊM TIẾNG ANH LỚP 7 CẢ NĂM FRIENDS PLUS SÁCH CHÂN TRỜI SÁNG TẠO ...Nguyen Thanh Tu Collection
https://app.box.com/s/qhtvq32h4ybf9t49ku85x0n3xl4jhr15Traditional Musical Instruments of Arunachal Pradesh and Uttar Pradesh - RAYH...
Traditional Musical Instruments of Arunachal Pradesh and Uttar Pradesh
Leveraging Generative AI to Drive Nonprofit Innovation
In this webinar, participants learned how to utilize Generative AI to streamline operations and elevate member engagement. Amazon Web Service experts provided a customer specific use cases and dived into low/no-code tools that are quick and easy to deploy through Amazon Web Service (AWS.)
LAND USE LAND COVER AND NDVI OF MIRZAPUR DISTRICT, UP
This Dissertation explores the particular circumstances of Mirzapur, a region located in the
core of India. Mirzapur, with its varied terrains and abundant biodiversity, offers an optimal
environment for investigating the changes in vegetation cover dynamics. Our study utilizes
advanced technologies such as GIS (Geographic Information Systems) and Remote sensing to
analyze the transformations that have taken place over the course of a decade.
The complex relationship between human activities and the environment has been the focus
of extensive research and worry. As the global community grapples with swift urbanization,
population expansion, and economic progress, the effects on natural ecosystems are becoming
more evident. A crucial element of this impact is the alteration of vegetation cover, which plays a
significant role in maintaining the ecological equilibrium of our planet.Land serves as the foundation for all human activities and provides the necessary materials for
these activities. As the most crucial natural resource, its utilization by humans results in different
'Land uses,' which are determined by both human activities and the physical characteristics of the
land.
The utilization of land is impacted by human needs and environmental factors. In countries
like India, rapid population growth and the emphasis on extensive resource exploitation can lead
to significant land degradation, adversely affecting the region's land cover.
Therefore, human intervention has significantly influenced land use patterns over many
centuries, evolving its structure over time and space. In the present era, these changes have
accelerated due to factors such as agriculture and urbanization. Information regarding land use and
cover is essential for various planning and management tasks related to the Earth's surface,
providing crucial environmental data for scientific, resource management, policy purposes, and
diverse human activities.
Accurate understanding of land use and cover is imperative for the development planning
of any area. Consequently, a wide range of professionals, including earth system scientists, land
and water managers, and urban planners, are interested in obtaining data on land use and cover
changes, conversion trends, and other related patterns. The spatial dimensions of land use and
cover support policymakers and scientists in making well-informed decisions, as alterations in
these patterns indicate shifts in economic and social conditions. Monitoring such changes with the
help of Advanced technologies like Remote Sensing and Geographic Information Systems is
crucial for coordinated efforts across different administrative levels. Advanced technologies like
Remote Sensing and Geographic Information Systems
9
Changes in vegetation cover refer to variations in the distribution, composition, and overall
structure of plant communities across different temporal and spatial scales. These changes can
occur natural.
Recently uploaded (20)
Walmart Business+ and Spark Good for Nonprofits.pdf
Walmart Business+ and Spark Good for Nonprofits.pdf
Film vocab for eal 3 students: Australia the movie
Film vocab for eal 3 students: Australia the movie
Constructing Your Course Container for Effective Communication
Constructing Your Course Container for Effective Communication
BÀI TẬP DẠY THÊM TIẾNG ANH LỚP 7 CẢ NĂM FRIENDS PLUS SÁCH CHÂN TRỜI SÁNG TẠO ...
BÀI TẬP DẠY THÊM TIẾNG ANH LỚP 7 CẢ NĂM FRIENDS PLUS SÁCH CHÂN TRỜI SÁNG TẠO ...
Traditional Musical Instruments of Arunachal Pradesh and Uttar Pradesh - RAYH...
Traditional Musical Instruments of Arunachal Pradesh and Uttar Pradesh - RAYH...
Leveraging Generative AI to Drive Nonprofit Innovation
Leveraging Generative AI to Drive Nonprofit Innovation
IGCSE Biology Chapter 14- Reproduction in Plants.pdf
IGCSE Biology Chapter 14- Reproduction in Plants.pdf
B. Ed Syllabus for babasaheb ambedkar education university.pdf
B. Ed Syllabus for babasaheb ambedkar education university.pdf
NEWSPAPERS - QUESTION 1 - REVISION POWERPOINT.pptx
NEWSPAPERS - QUESTION 1 - REVISION POWERPOINT.pptx
LAND USE LAND COVER AND NDVI OF MIRZAPUR DISTRICT, UP
LAND USE LAND COVER AND NDVI OF MIRZAPUR DISTRICT, UP
BeO Vibrational Transitions.pdf
- 1. 1 The vibrational transition in BeO is observed at a wavelength of 6.724 μm. What is the effective force constant of BeO? Helping Tools No.1 No.2
- 2. 2 No.3 Solution 1 2 1 2 2 Let us first calculate the reduced mass of BeO as (9.0122 )(15.9994) (9.0122 ) (15.9994) 144.19 5.76 25.01 r m m m m m u u u u u = + = + = =
- 3. 3 8 6 14 1 12 We know that frequency & wavelength are related by 3 10 6.724 10 0.446 10 44.6 10 m X c s f X m X Xs X Hz − − = = = = 2 2 2 2 2 2 We know that vibrational frequency is given as: 1 1 2 2 1 4 k kXc f m mXc kc f X mc = = = 2 2 2 2 12 2 2 2 24 2 2 16 2 24 6 16 2 30 16 2 14 18 2 4 (44.6 10 ) 4 (3.14) 5.76 931.5 1989.16 10 ( ) 39.44 5365.44 9 10 420932022.78 10 10 9 10 420932022.78 10 9 10 46770224.75 10 4677.022475 10 f X Xmc k c X Hz X X X X MeV c X Hz X X MeV m X s X X eV X m X eV X m X eV X e m = = = = = = = 2 21 3 2 2 4.677 10 4.677 10 ( ) V m eV eV X X m nm = =