This document provides specifications for a solar pumping project in Baladweyne, Somalia. It includes details of the system components, layout, wiring diagram, and performance data. The key components are a PSk2-40 solar pump controller, CS-G200-24/4 surface pump unit, and 144 photovoltaic panels totalling 46,800Wp. The system is designed to pump up to 3,000m3 of water per day from a water source at 1m depth to an irrigation system with a maximum pressure of 12m and flow rate of 499m3/h. Daily and monthly output values are provided based on local weather data.
This document provides specifications for a solar submersible pump system for 6" wells including a high efficiency solar pump controller that supports hybrid power sources and has onboard data logging. The system has a maximum head of 200m, flow rate of 63m3/h, and uses a 3-phase AC motor pump unit with stainless steel components that can operate at depths up to 300m.
This document provides specifications for a 42.585 kW solar photovoltaic system to be installed at a residential property located at 21511 US Hwy 63 N in Sturgeon, Missouri. The system will include 255 Q-Cell solar panels, two Fronius inverters, attachment hardware, and electrical equipment. It includes diagrams of the proposed array layout, electrical connections, and component specifications. The installation is designed to feed solar power directly to the site transformer for use by the property.
This document summarizes the specifications of a solar submersible pump system for 4" wells. The system includes a PS600 controller with integrated data logging and pump management features. It also includes an ECDRIVE 600-C brushless DC motor rated for 0.7 kW, and a PE C-SJ5-8 centrifugal pump end made of stainless steel. The pump unit is designed for boreholes at least 4" in diameter, with a maximum flow rate of 6.5 m3/h and head up to 30 m. The system complies with various international safety and electromagnetic compatibility standards.
This document provides an operation manual for the Vortex Flow Meter Model LUGB. It describes the product's general information including its description, operational principle, structure, technical data, and cautions for installation. The document also covers electrical wiring details for the different meter models and programming/setup instructions.
IRJET- Review on Micro Air Consumption Engine Vehicle with Energy MultiplierIRJET Journal
This document summarizes a review on developing a micro air consumption engine vehicle with an energy multiplier. The system aims to utilize exceptionally small amounts of compressed air (3cc per stroke) from an air tank to drive a piston in a cylinder. This motion is converted to rotary by a rack and pinion system and transferred to a flywheel energy multiplier. Together, the low air consumption engine and flywheel are intended to provide improved mileage from compressed air compared to conventional high air consumption systems. The review covers the design, components, calculations, advantages and applications of combining a micro air engine with an energy multiplier flywheel system to displace a vehicle.
The document provides installation and operation instructions for the Hygrotec MMY 170 trace moisture analyser. It consists of an Endress+Hauser DY75 gold/aluminum oxide probe and MMY 170 electronics module. Key features include measuring moisture as dewpoint in ppmv, temperature measurement, E+H bus communication, and optional liquid ppmw measurement. The document provides details on probe installation, analyser mounting and connection, programming functions, troubleshooting, and intrinsic safety certification.
This document provides specifications and performance data for Lamb Electric vacuum motors models 116157-00, 116157-29, and 116157-32. It includes details on the motor design such as its dimensions, voltage, bearings, and safety features. The document also contains charts displaying the motors' airflow and vacuum performance rates across a range of orifice diameters.
Mineral Water Bottling Plant, Installation Available. ₹ 5.50 Lakh / Unit ; Mineral Water Bottling Plant. ₹ 40 Lakh / starting.
Steps to Start Mineral Water Plant Business · 1. Know the market opportunity · 2. Certification and License · 3. Good area and locality, This bottling plant is used in numerous industries for solving drinking water issues. Due to the easy installation, our Mineral Water Bottling Plant, A packaged potable water plant filtrates and processes borewell water with the aid of reverse osmosis and packages it into bottles. This bottling plant is used in numerous industries for solving drinking water issues. Due to the easy installation, our Mineral Water Bottling Plant, Mineral Water Process Details Mineral Water Bottling Plant ... World Latest Technologies of Process for Mineral Water (Bottled Water) Production from Different, Mineral water plant requires the water coming from naturally occurring sources like mountain water and spring water. Such water involves minerals that offer drinking water, ... Water Plant, 24 BPM Packaged Drinking Water Plant and Mineral Water Bottle Filling Machine offered by Gajanand Machine Private Limted, Surat, Gujarat.
This document provides specifications for a solar submersible pump system for 6" wells including a high efficiency solar pump controller that supports hybrid power sources and has onboard data logging. The system has a maximum head of 200m, flow rate of 63m3/h, and uses a 3-phase AC motor pump unit with stainless steel components that can operate at depths up to 300m.
This document provides specifications for a 42.585 kW solar photovoltaic system to be installed at a residential property located at 21511 US Hwy 63 N in Sturgeon, Missouri. The system will include 255 Q-Cell solar panels, two Fronius inverters, attachment hardware, and electrical equipment. It includes diagrams of the proposed array layout, electrical connections, and component specifications. The installation is designed to feed solar power directly to the site transformer for use by the property.
This document summarizes the specifications of a solar submersible pump system for 4" wells. The system includes a PS600 controller with integrated data logging and pump management features. It also includes an ECDRIVE 600-C brushless DC motor rated for 0.7 kW, and a PE C-SJ5-8 centrifugal pump end made of stainless steel. The pump unit is designed for boreholes at least 4" in diameter, with a maximum flow rate of 6.5 m3/h and head up to 30 m. The system complies with various international safety and electromagnetic compatibility standards.
This document provides an operation manual for the Vortex Flow Meter Model LUGB. It describes the product's general information including its description, operational principle, structure, technical data, and cautions for installation. The document also covers electrical wiring details for the different meter models and programming/setup instructions.
IRJET- Review on Micro Air Consumption Engine Vehicle with Energy MultiplierIRJET Journal
This document summarizes a review on developing a micro air consumption engine vehicle with an energy multiplier. The system aims to utilize exceptionally small amounts of compressed air (3cc per stroke) from an air tank to drive a piston in a cylinder. This motion is converted to rotary by a rack and pinion system and transferred to a flywheel energy multiplier. Together, the low air consumption engine and flywheel are intended to provide improved mileage from compressed air compared to conventional high air consumption systems. The review covers the design, components, calculations, advantages and applications of combining a micro air engine with an energy multiplier flywheel system to displace a vehicle.
The document provides installation and operation instructions for the Hygrotec MMY 170 trace moisture analyser. It consists of an Endress+Hauser DY75 gold/aluminum oxide probe and MMY 170 electronics module. Key features include measuring moisture as dewpoint in ppmv, temperature measurement, E+H bus communication, and optional liquid ppmw measurement. The document provides details on probe installation, analyser mounting and connection, programming functions, troubleshooting, and intrinsic safety certification.
This document provides specifications and performance data for Lamb Electric vacuum motors models 116157-00, 116157-29, and 116157-32. It includes details on the motor design such as its dimensions, voltage, bearings, and safety features. The document also contains charts displaying the motors' airflow and vacuum performance rates across a range of orifice diameters.
Mineral Water Bottling Plant, Installation Available. ₹ 5.50 Lakh / Unit ; Mineral Water Bottling Plant. ₹ 40 Lakh / starting.
Steps to Start Mineral Water Plant Business · 1. Know the market opportunity · 2. Certification and License · 3. Good area and locality, This bottling plant is used in numerous industries for solving drinking water issues. Due to the easy installation, our Mineral Water Bottling Plant, A packaged potable water plant filtrates and processes borewell water with the aid of reverse osmosis and packages it into bottles. This bottling plant is used in numerous industries for solving drinking water issues. Due to the easy installation, our Mineral Water Bottling Plant, Mineral Water Process Details Mineral Water Bottling Plant ... World Latest Technologies of Process for Mineral Water (Bottled Water) Production from Different, Mineral water plant requires the water coming from naturally occurring sources like mountain water and spring water. Such water involves minerals that offer drinking water, ... Water Plant, 24 BPM Packaged Drinking Water Plant and Mineral Water Bottle Filling Machine offered by Gajanand Machine Private Limted, Surat, Gujarat.
The document provides technical specifications for Carrier's 42GWC hydronic cassette fan coil unit. It includes details on the unit's air flow rates, cooling and heating capacities, dimensions, electrical requirements, and performance data for various models. Ordering information is also provided, with notes on installation, maintenance, and applicable standards.
SolarEdge provides a commercial solar solution that offers four key benefits over traditional inverters: increased energy yield, lower operations and maintenance costs, enhanced safety, and more flexible design. Their solution utilizes power optimizers at the module level and monitoring software to maximize energy production, reduce costs over the system lifetime, and improve safety during installation and maintenance. While their inverters have a slightly higher upfront cost, SolarEdge's end-to-end solution offsets this with reduced balance of system costs, lower maintenance expenses, and increased energy production over time.
The document discusses Belimo's Energy Valve 3.0, which provides advanced pressure-independent control of hydronic systems. Key features include enhanced delta T management, glycol monitoring using an ultrasonic flow meter, cloud-based services for remote monitoring and optimization, and an improved user interface. Case studies show how the valve increased delta T and reduced energy costs for customers such as MIT. The valve comes in sizes from 1/2-inch to 6-inches to handle flow rates from 5.5 GPM to 713 GPM, and pricing information is provided for NPT and ANSI flanged models.
1500V String Inverter Utility PV System Solution 2021.pdfgoangagoanga99
This document provides information about KSTAR Science & Technology Co., including:
- KSTAR is a pioneer in UPS and PV inverter systems in China, founded in 1993.
- They have an R&D and manufacturing base of 150,000 square meters and provide products to over 90 countries worldwide.
- KSTAR's product portfolio includes data center ESS, EV chargers, PV inverters, and ESS solutions.
- Specific details are provided about KSTAR's 1500Vdc 800Vac KSG-250UH utility-scale PV inverter, including its specifications, monitoring features, efficiency, cooling system, and grid support capabilities.
This document summarizes a proposed 3 kW residential solar PV system for a customer in Flagstaff Hill, Australia. The system would include 12 solar panels mounted on the roof with an estimated annual output of 4,623 kWh. It is estimated that 2,534 kWh would be used on-site annually, with the remaining 2,089 kWh exported to the grid. The total estimated system cost is $5,600 and the payback period is estimated to be over 3 years.
This document describes the design and installation of a low-cost wind monitoring system using scrap and readily available materials. It consists of a 4-cup anemometer to measure wind speed, a lightweight wind vane to measure wind direction, and a platinum resistance temperature detector to measure ambient air temperature. The system provides accurate measurements at a fraction of the cost of a commercial system. It was calibrated and tested and found to perform reliably while significantly reducing costs for small industries.
The document describes the Sunny Tripower series of large-scale inverters for commercial and utility-scale solar installations. The inverters come in 15000TL, 20000TL, and 25000TL models and offer high efficiency up to 98.4%, flexible design options like wide input voltage range and multistring capability, and innovative grid support functions without additional hardware. Key features include integrated plant control, reactive power support, and safety features. Technical specifications are provided for each model.
This document summarizes a research project on optimizing a regional network pump station through the use of glass reinforced plastics (GRP) materials. The research aims to plan and design the low and medium voltage electrical systems for a pump station serving 650,000 people. It also calculates reductions in total head and power consumption by applying the Hazen-Williams equation and analyzing replacing ductile iron pipes with GRP. The results show potential energy cost savings of over RM500,000 per year and a simple payback period of 10 years by using GRP instead of ductile iron. The research also developed optimized switchgear designs for the electrical services.
The document provides details about the engineering department of a factory. It includes information about the electrical department structure, motor winding and repair teams, power distribution systems, equipment specifications, maintenance procedures, and utilities like compressors, cooling towers, and the power house. The summaries include essential information about the departments, equipment, and maintenance procedures.
The document provides information about a refinery including:
- It started operating in 1984 as a joint venture and now processes 400,000 BPD of crude oil.
- Its main product yields are gasoline, diesel, jet fuel, and fuel oil.
- It has technical, operations, maintenance, and financial departments.
- Case studies examine crude distillation unit stream flows over 10 years and calculate heat exchanger fouling rates to predict cleaning needs.
- An experience overview discusses the refinery's induction program and a heat exchanger bundle replacement and testing project.
The document provides specifications for Samsung's DVM S WATER outdoor units, including the AM080FXWANR, AM100FXWANR, AM120FXWANR, and AM160FXWANR models. It lists key details like cooling and heating capacities, power consumption, compressor type, condenser type, piping connections, installation limitations, refrigerant type, sound levels, dimensions, and operating temperature ranges. The specifications are intended to help understand the performance and technical requirements of the outdoor units.
The CECRE: Making renewable energy technologies compatible with the security ...IrSOLaV Pomares
Red Eléctrica de España is the Spanish transmission system operator. It operates and maintains the transmission grid to ensure security of electricity supply. Renewable energy sources now account for 39% of Spain's installed capacity, including 22.6% from wind and 4.4% from solar PV. Integrating high levels of renewable energy presents challenges like variability in generation, lack of observability and controllability, and impacts on grid constraints and voltage control. The CECRE control center helps address these issues by providing centralized monitoring and control of renewable facilities.
2014 Googol gas generator introduction-googol(1)Mike Renko
Googol Engine-Tech Co. produces gas and diesel engines for power generation. They have manufacturing bases in China and the US. Their product lines include the R series gas generators from 160kW to 500kW and the J series from 600kW to 1452kW. The document provides technical specifications and components for their gas generator sets including engines, alternators, control systems, and other electrical and mechanical components.
The document summarizes the key features and advantages of the BSTA 410 stamping press from Bruderer. It has an adjustable stroke system for flexibility and quality control. Its unique lever system distributes load for durability. Additional features include ram adjustment during operation, integrated monitoring, and easy attachment of peripheral devices to maximize efficiency. Bruderer uses this press to help customers in various industries like automotive and electronics produce high-precision parts.
Stand-alone (off-grid) isolated renewable solar and wind system. Explaining how stand-alone AC mini-grid renewable system works and how we can be custiomized in size to every customer.
This document provides information on a motor control center project including:
1) Safety regulations and instructions for working on the motor control center.
2) A wiring diagram showing the electrical connections for a drive and associated safety components in the motor control center.
3) Additional diagrams showing connections for emergency stop buttons and fans for cooling the motor control center.
The energy and chemical industry must embrace triple bottom line performance in order to to drive sustainability targets and achieve net-zero emissions, well-being of all, and circular economy. This involves placing equal importance on people, the environment, and profits, in order to drive sustainability outcomes which are existential to everyone.
This document provides a quick guide for installing and programming a VLT HVAC Basic Drive frequency converter. It includes sections on safety warnings, introduction/approvals, installation instructions, programming, parameters, warnings/alarms, specifications, and options. The installation section describes dimensions, clearances, electrical connections, and EMC requirements. Programming can be done using the local control panel or start-up wizard. Parameters and specifications are listed for configuration and technical reference.
Optimal Cable Sizing in PV Systems: Case StudyLeonardo ENERGY
It is often beneficial to over-size the cross-section of electricity cables compared to the standard values that follow out of voltage and current calculations. In the large majority of cases, oversizing has a positive influence on the Life Cycle Cost of the installation. The investment in larger cable is easily paid back by the reduction of Joule losses inside the cable and the subsequent savings on electricity bills.
When the cable is part of a photovoltaic (PV) installation, the investment in a larger-than-standard cable is paid back even faster than in other installations. This is because the allocated electricity price for a PV installation is higher than the market price thanks to the feed-in tariff or green certificates. In other words: the energy losses that are avoided in a PV installation lead to an even bigger financial reward than in other installations.
Increasing the cable cross section in PV installations also creates additional technical and environmental benefits.
Epcon is One of the World's leading Manufacturing Companies.EpconLP
Epcon is One of the World's leading Manufacturing Companies. With over 4000 installations worldwide, EPCON has been pioneering new techniques since 1977 that have become industry standards now. Founded in 1977, Epcon has grown from a one-man operation to a global leader in developing and manufacturing innovative air pollution control technology and industrial heating equipment.
More Related Content
Similar to Baladweyne-Irrigation-System__13m_3,690cbm_46,800Wp.pdf
The document provides technical specifications for Carrier's 42GWC hydronic cassette fan coil unit. It includes details on the unit's air flow rates, cooling and heating capacities, dimensions, electrical requirements, and performance data for various models. Ordering information is also provided, with notes on installation, maintenance, and applicable standards.
SolarEdge provides a commercial solar solution that offers four key benefits over traditional inverters: increased energy yield, lower operations and maintenance costs, enhanced safety, and more flexible design. Their solution utilizes power optimizers at the module level and monitoring software to maximize energy production, reduce costs over the system lifetime, and improve safety during installation and maintenance. While their inverters have a slightly higher upfront cost, SolarEdge's end-to-end solution offsets this with reduced balance of system costs, lower maintenance expenses, and increased energy production over time.
The document discusses Belimo's Energy Valve 3.0, which provides advanced pressure-independent control of hydronic systems. Key features include enhanced delta T management, glycol monitoring using an ultrasonic flow meter, cloud-based services for remote monitoring and optimization, and an improved user interface. Case studies show how the valve increased delta T and reduced energy costs for customers such as MIT. The valve comes in sizes from 1/2-inch to 6-inches to handle flow rates from 5.5 GPM to 713 GPM, and pricing information is provided for NPT and ANSI flanged models.
1500V String Inverter Utility PV System Solution 2021.pdfgoangagoanga99
This document provides information about KSTAR Science & Technology Co., including:
- KSTAR is a pioneer in UPS and PV inverter systems in China, founded in 1993.
- They have an R&D and manufacturing base of 150,000 square meters and provide products to over 90 countries worldwide.
- KSTAR's product portfolio includes data center ESS, EV chargers, PV inverters, and ESS solutions.
- Specific details are provided about KSTAR's 1500Vdc 800Vac KSG-250UH utility-scale PV inverter, including its specifications, monitoring features, efficiency, cooling system, and grid support capabilities.
This document summarizes a proposed 3 kW residential solar PV system for a customer in Flagstaff Hill, Australia. The system would include 12 solar panels mounted on the roof with an estimated annual output of 4,623 kWh. It is estimated that 2,534 kWh would be used on-site annually, with the remaining 2,089 kWh exported to the grid. The total estimated system cost is $5,600 and the payback period is estimated to be over 3 years.
This document describes the design and installation of a low-cost wind monitoring system using scrap and readily available materials. It consists of a 4-cup anemometer to measure wind speed, a lightweight wind vane to measure wind direction, and a platinum resistance temperature detector to measure ambient air temperature. The system provides accurate measurements at a fraction of the cost of a commercial system. It was calibrated and tested and found to perform reliably while significantly reducing costs for small industries.
The document describes the Sunny Tripower series of large-scale inverters for commercial and utility-scale solar installations. The inverters come in 15000TL, 20000TL, and 25000TL models and offer high efficiency up to 98.4%, flexible design options like wide input voltage range and multistring capability, and innovative grid support functions without additional hardware. Key features include integrated plant control, reactive power support, and safety features. Technical specifications are provided for each model.
This document summarizes a research project on optimizing a regional network pump station through the use of glass reinforced plastics (GRP) materials. The research aims to plan and design the low and medium voltage electrical systems for a pump station serving 650,000 people. It also calculates reductions in total head and power consumption by applying the Hazen-Williams equation and analyzing replacing ductile iron pipes with GRP. The results show potential energy cost savings of over RM500,000 per year and a simple payback period of 10 years by using GRP instead of ductile iron. The research also developed optimized switchgear designs for the electrical services.
The document provides details about the engineering department of a factory. It includes information about the electrical department structure, motor winding and repair teams, power distribution systems, equipment specifications, maintenance procedures, and utilities like compressors, cooling towers, and the power house. The summaries include essential information about the departments, equipment, and maintenance procedures.
The document provides information about a refinery including:
- It started operating in 1984 as a joint venture and now processes 400,000 BPD of crude oil.
- Its main product yields are gasoline, diesel, jet fuel, and fuel oil.
- It has technical, operations, maintenance, and financial departments.
- Case studies examine crude distillation unit stream flows over 10 years and calculate heat exchanger fouling rates to predict cleaning needs.
- An experience overview discusses the refinery's induction program and a heat exchanger bundle replacement and testing project.
The document provides specifications for Samsung's DVM S WATER outdoor units, including the AM080FXWANR, AM100FXWANR, AM120FXWANR, and AM160FXWANR models. It lists key details like cooling and heating capacities, power consumption, compressor type, condenser type, piping connections, installation limitations, refrigerant type, sound levels, dimensions, and operating temperature ranges. The specifications are intended to help understand the performance and technical requirements of the outdoor units.
The CECRE: Making renewable energy technologies compatible with the security ...IrSOLaV Pomares
Red Eléctrica de España is the Spanish transmission system operator. It operates and maintains the transmission grid to ensure security of electricity supply. Renewable energy sources now account for 39% of Spain's installed capacity, including 22.6% from wind and 4.4% from solar PV. Integrating high levels of renewable energy presents challenges like variability in generation, lack of observability and controllability, and impacts on grid constraints and voltage control. The CECRE control center helps address these issues by providing centralized monitoring and control of renewable facilities.
2014 Googol gas generator introduction-googol(1)Mike Renko
Googol Engine-Tech Co. produces gas and diesel engines for power generation. They have manufacturing bases in China and the US. Their product lines include the R series gas generators from 160kW to 500kW and the J series from 600kW to 1452kW. The document provides technical specifications and components for their gas generator sets including engines, alternators, control systems, and other electrical and mechanical components.
The document summarizes the key features and advantages of the BSTA 410 stamping press from Bruderer. It has an adjustable stroke system for flexibility and quality control. Its unique lever system distributes load for durability. Additional features include ram adjustment during operation, integrated monitoring, and easy attachment of peripheral devices to maximize efficiency. Bruderer uses this press to help customers in various industries like automotive and electronics produce high-precision parts.
Stand-alone (off-grid) isolated renewable solar and wind system. Explaining how stand-alone AC mini-grid renewable system works and how we can be custiomized in size to every customer.
This document provides information on a motor control center project including:
1) Safety regulations and instructions for working on the motor control center.
2) A wiring diagram showing the electrical connections for a drive and associated safety components in the motor control center.
3) Additional diagrams showing connections for emergency stop buttons and fans for cooling the motor control center.
The energy and chemical industry must embrace triple bottom line performance in order to to drive sustainability targets and achieve net-zero emissions, well-being of all, and circular economy. This involves placing equal importance on people, the environment, and profits, in order to drive sustainability outcomes which are existential to everyone.
This document provides a quick guide for installing and programming a VLT HVAC Basic Drive frequency converter. It includes sections on safety warnings, introduction/approvals, installation instructions, programming, parameters, warnings/alarms, specifications, and options. The installation section describes dimensions, clearances, electrical connections, and EMC requirements. Programming can be done using the local control panel or start-up wizard. Parameters and specifications are listed for configuration and technical reference.
Optimal Cable Sizing in PV Systems: Case StudyLeonardo ENERGY
It is often beneficial to over-size the cross-section of electricity cables compared to the standard values that follow out of voltage and current calculations. In the large majority of cases, oversizing has a positive influence on the Life Cycle Cost of the installation. The investment in larger cable is easily paid back by the reduction of Joule losses inside the cable and the subsequent savings on electricity bills.
When the cable is part of a photovoltaic (PV) installation, the investment in a larger-than-standard cable is paid back even faster than in other installations. This is because the allocated electricity price for a PV installation is higher than the market price thanks to the feed-in tariff or green certificates. In other words: the energy losses that are avoided in a PV installation lead to an even bigger financial reward than in other installations.
Increasing the cable cross section in PV installations also creates additional technical and environmental benefits.
Similar to Baladweyne-Irrigation-System__13m_3,690cbm_46,800Wp.pdf (20)
Epcon is One of the World's leading Manufacturing Companies.EpconLP
Epcon is One of the World's leading Manufacturing Companies. With over 4000 installations worldwide, EPCON has been pioneering new techniques since 1977 that have become industry standards now. Founded in 1977, Epcon has grown from a one-man operation to a global leader in developing and manufacturing innovative air pollution control technology and industrial heating equipment.
Climate Change All over the World .pptxsairaanwer024
Climate change refers to significant and lasting changes in the average weather patterns over periods ranging from decades to millions of years. It encompasses both global warming driven by human emissions of greenhouse gases and the resulting large-scale shifts in weather patterns. While climate change is a natural phenomenon, human activities, particularly since the Industrial Revolution, have accelerated its pace and intensity
Improving the viability of probiotics by encapsulation methods for developmen...Open Access Research Paper
The popularity of functional foods among scientists and common people has been increasing day by day. Awareness and modernization make the consumer think better regarding food and nutrition. Now a day’s individual knows very well about the relation between food consumption and disease prevalence. Humans have a diversity of microbes in the gut that together form the gut microflora. Probiotics are the health-promoting live microbial cells improve host health through gut and brain connection and fighting against harmful bacteria. Bifidobacterium and Lactobacillus are the two bacterial genera which are considered to be probiotic. These good bacteria are facing challenges of viability. There are so many factors such as sensitivity to heat, pH, acidity, osmotic effect, mechanical shear, chemical components, freezing and storage time as well which affects the viability of probiotics in the dairy food matrix as well as in the gut. Multiple efforts have been done in the past and ongoing in present for these beneficial microbial population stability until their destination in the gut. One of a useful technique known as microencapsulation makes the probiotic effective in the diversified conditions and maintain these microbe’s community to the optimum level for achieving targeted benefits. Dairy products are found to be an ideal vehicle for probiotic incorporation. It has been seen that the encapsulated microbial cells show higher viability than the free cells in different processing and storage conditions as well as against bile salts in the gut. They make the food functional when incorporated, without affecting the product sensory characteristics.
Optimizing Post Remediation Groundwater Performance with Enhanced Microbiolog...Joshua Orris
Results of geophysics and pneumatic injection pilot tests during 2003 – 2007 yielded significant positive results for injection delivery design and contaminant mass treatment, resulting in permanent shut-down of an existing groundwater Pump & Treat system.
Accessible source areas were subsequently removed (2011) by soil excavation and treated with the placement of Emulsified Vegetable Oil EVO and zero-valent iron ZVI to accelerate treatment of impacted groundwater in overburden and weathered fractured bedrock. Post pilot test and post remediation groundwater monitoring has included analyses of CVOCs, organic fatty acids, dissolved gases and QuantArray® -Chlor to quantify key microorganisms (e.g., Dehalococcoides, Dehalobacter, etc.) and functional genes (e.g., vinyl chloride reductase, methane monooxygenase, etc.) to assess potential for reductive dechlorination and aerobic cometabolism of CVOCs.
In 2022, the first commercial application of MetaArray™ was performed at the site. MetaArray™ utilizes statistical analysis, such as principal component analysis and multivariate analysis to provide evidence that reductive dechlorination is active or even that it is slowing. This creates actionable data allowing users to save money by making important site management decisions earlier.
The results of the MetaArray™ analysis’ support vector machine (SVM) identified groundwater monitoring wells with a 80% confidence that were characterized as either Limited for Reductive Decholorination or had a High Reductive Reduction Dechlorination potential. The results of MetaArray™ will be used to further optimize the site’s post remediation monitoring program for monitored natural attenuation.
Presented by The Global Peatlands Assessment: Mapping, Policy, and Action at GLF Peatlands 2024 - The Global Peatlands Assessment: Mapping, Policy, and Action
Evolving Lifecycles with High Resolution Site Characterization (HRSC) and 3-D...Joshua Orris
The incorporation of a 3DCSM and completion of HRSC provided a tool for enhanced, data-driven, decisions to support a change in remediation closure strategies. Currently, an approved pilot study has been obtained to shut-down the remediation systems (ISCO, P&T) and conduct a hydraulic study under non-pumping conditions. A separate micro-biological bench scale treatability study was competed that yielded positive results for an emerging innovative technology. As a result, a field pilot study has commenced with results expected in nine-twelve months. With the results of the hydraulic study, field pilot studies and an updated risk assessment leading site monitoring optimization cost lifecycle savings upwards of $15MM towards an alternatively evolved best available technology remediation closure strategy.
ENVIRONMENT~ Renewable Energy Sources and their future prospects.tiwarimanvi3129
This presentation is for us to know that how our Environment need Attention for protection of our natural resources which are depleted day by day that's why we need to take time and shift our attention to renewable energy sources instead of non-renewable sources which are better and Eco-friendly for our environment. these renewable energy sources are so helpful for our planet and for every living organism which depends on environment.
1. Parameter
Location: , (5° North; 45° East) Water temperature: 25 °C Altitude 182 m
Required daily output: 3,000 m³; Sizing for average month Dirt loss: 5.0 % Motor cable: 50 m
Pipe type (Discharge
side):
- Dynamic pressure
head:
12 m Pipe length (Discharge
side):
-
Pipe type (Suction
side):
plastic, drawn/pressed, new: 0.007 mm Suction head: 1 m Pipe length (Suction side): 10 m
Products Quantity Details
PSk2-40 CS-G200-24/4 1 pc. Surface pump system including controller with DataModule, motor and pump end
JA325P-72 144 pc. 46,800 Wp; 18 x 8 modules; 15 ° tilted
Motor cable 50 m 16 mm² 3-phase cable for power and 1-phase cable for ground
Pipeline (Suction side) 10 m 225 mm (inner diameter) Pipeline
Accessories 1 set Water Sensor, Float Switch, Surge Protector, 2x PV Disconnect 1000-40-5, PV Combiner 1000-
125-4, PV Protect 1000-125, SmartPSUk2, SmartStart
Daily output in average month 3,690 m³
Daily values Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Av.
Output [m³]
Energy [kWh] 267 279 265 225 210 192 188 213 244 221 237 257 233
Irradiation [kWh/m²] 6.7 7.1 6.8 5.7 5.3 4.8 4.7 5.4 6.2 5.5 5.9 6.4 5.9
Rainfall [mm] 0.033 0.033 0.33 2.4 2.7 0.37 0 0.033 0.40 2.7 1.3 0.20 0.87
Ambient temp. [°C] 28 28 29 29 29 28 28 28 28 28 27 27 28
Hourly values 6:00 7:00 8:00 9:00 10:00 11:00 12:00 13:00 14:00 15:00 16:00 17:00 18:00
Output [m³/h]
Energy [kWh] 0.060 7.3 15 22 27 30 31 30 27 22 15 7.0 0.058
Irradiation [kWh/m²] 0.001 0.17 0.36 0.54 0.69 0.77 0.80 0.77 0.69 0.54 0.36 0.17 0.001
Ambient temp. [°C] 23 23 24 26 28 30 32 33 33 33 33 32 32
SunSwitch setting in PumpScanner min. 150 W/m²
Created by LORENTZ COMPASS 3.1.0.134
All specifications and information are given with good intent, errors are possible and products may be subject to change
without notice.
1/5
Mogadishu
Somalia
www.solargentechnologies.
Abubakar Aidarus
Tel: +252 616 100 174/+252 618 515
416
Fax:
abubakar@solargentechnologies.co
SOLARGEN TECHNOLOGIES LTD
Wednesday, July 31, 2019
Baladweyne Irrigation System
Solar pumping project
2. System characteristic
Min. 800 W/m², 20 °C Max./STC*
PV generator Cell temperature [°C] 46 25
Temperature loss [%] 8.8 -
Dirt loss [%] 5.0 -
Pmax [Wp] 32,450 46,800
Vmp [V] 614 673
Imp [A] 53 70
Voc [V] 760 835
Isc [A] 54 70
Pout [W] 31,500 -
Vout [V] 645 -
Iout [A] 49 -
Motor cable Power loss [%] 0.69 1.6 1.6
Pump systems Motor power [W] 6,180 30,750 30,750
Motor voltage [V AC] 258 380 380
Motor current [A] 16 55 55
Motor speed [rpm] 1,010 1,505 1,505
Frequency [Hz] 34 51 51
Flow rate [m³/h] 11 481 481
Efficiency [%] 5.8 57 67
Friction loss suction side [m] 0.001 1.0 1.0
NPSH [m] 2.8 7.23 7.23
*STC: Standard test conditions for photovoltaic modules, 1000 W/m² solar iradiance, 25 °C cell temperature
Created by LORENTZ COMPASS 3.1.0.134
All specifications and information are given with good intent, errors are possible and products may be subject to change
without notice.
2/5
Mogadishu
Somalia
www.solargentechnologies.
Abubakar Aidarus
Tel: +252 616 100 174/+252 618 515
416
Fax:
abubakar@solargentechnologies.co
SOLARGEN TECHNOLOGIES LTD
Wednesday, July 31, 2019
Baladweyne Irrigation System
Solar pumping project
3. Wiring diagram
Created by LORENTZ COMPASS 3.1.0.134
All specifications and information are given with good intent, errors are possible and products may be subject to change
without notice.
3/5
Mogadishu
Somalia
www.solargentechnologies.
Abubakar Aidarus
Tel: +252 616 100 174/+252 618 515
416
Fax:
abubakar@solargentechnologies.co
SOLARGEN TECHNOLOGIES LTD
Wednesday, July 31, 2019
Baladweyne Irrigation System
Solar pumping project
4. System Layout
1: PSk2 Controller
2: Surface Pump
3: Pressure Sensor
4: Water Meter
5: Gate Valve
6: Filler
7: Water Sensor
8: Strainer
9: Filter Cage
10: Nonreturn Valve
11: Surge Protector*
12: Grounding Rod
13: Float Switch
14: PV Module for Sun Switch
15: PV Disconnect
16: PV Generator
17: PV Combiner
18: PV Protect
19: Float Switch for Well Probe
*It is recommended to install a Surge Protector at each
controller sensor input.
Created by LORENTZ COMPASS 3.1.0.134
All specifications and information are given with good intent, errors are possible and products may be subject to change
without notice.
4/5
Mogadishu
Somalia
www.solargentechnologies.
Abubakar Aidarus
Tel: +252 616 100 174/+252 618 515
416
Fax:
abubakar@solargentechnologies.co
SOLARGEN TECHNOLOGIES LTD
Wednesday, July 31, 2019
Baladweyne Irrigation System
Solar pumping project
5. Sizing Layout
P (Pressure head): Vertical height from the pump outlet to the highest point of delivery.
S (Suction head): Vertical height from the water level to the pump inlet where the water level is below the pump inlet.
B (Drawdown): Lowering of water level depending on flow rate and recovery rate of the reservoir.
D1 (Pipeline inner diameter
(Suction side))
D2 (Pipeline inner diameter
(Discharge side))
L1 (Pipe length (Suction
side)):
Pipe length from the water level to the pump inlet. Elbows and other fittings must be added as an equivalent
length of pipeline (the losses of a 90° long radius elbow and of a check valve are already included in the
calculation).
L2 (Pipe length (Discharge
side)):
Pipe length from the pump outlet to the point of delivery. Elbows and other fittings must be added as an equivalent
length of pipeline.
M (Motor cable): The cable between controller and pump unit.
T (Tilt angle): Angle of the PV generator surface from the horizontal plane.
Created by LORENTZ COMPASS 3.1.0.134
All specifications and information are given with good intent, errors are possible and products may be subject to change
without notice.
5/5
Mogadishu
Somalia
www.solargentechnologies.
Abubakar Aidarus
Tel: +252 616 100 174/+252 618 515
416
Fax:
abubakar@solargentechnologies.co
SOLARGEN TECHNOLOGIES LTD
Wednesday, July 31, 2019
Baladweyne Irrigation System
Solar pumping project
6. Head max. 22 m
Flow rate max. 499 m³/h
Controller PSk2-40
ƒHigh efficiency solar pump controller
ƒHybrid power (solar / grid / generator) support with LORENTZ
SmartSolution
ƒInputs for water meter, pressure sensors, digital switches
ƒSimple configuration with LORENTZ PumpScanner AndroidŒApp
ƒOnboard data logging and system monitoring
ƒInbuilt applications for constant pressure, constant flow and daily
amount
ƒIntegrated Sun Sensor
ƒActive temperature management
ƒIntegrated MPPT (Maximum Power Point Tracking)
Power max. 37 kW
Input voltage max. 850 V
Optimum Vmp** 575 V
Motor current max. 65 A
Efficiency max. 98 %
Ambient temp. -30...50 °C
Enclosure class IP54
Motor AC DRIVE CS-G 30kW/4p
ƒHighly efficient 3-phase AC motor
ƒFrequency: 25...51 Hz
Efficiency max. 86 %
Motor speed 740...1,510 rpm
Power factor 0.86
Insulation class F
Enclosure class IPX4
Pump End PE CS-G200-24/4
ƒPremium materials
ƒCentrifugal pump
Efficiency max. 85 %
Standards
2006/42/EC, 2004/108/EC, 2006/95/EC
IEC/EN 61702:1995, IEC/EN 62253 Ed.1
The logos shown reflect the approvals that have been granted for this product family. Products are ordered and supplied with the approvals specific to the market
requirements.
Pump Unit PUk2-40 CS-G200-24/4 (Motor, Pump End)
Water temperature max. 90 °C****
Suction head acc. to COMPASS sizing
Technical Data
System Overview
**Vmp: MPP-voltage under Standard Test Conditions (STC): 1000 W/m² solar irradiance, 25 °C cell temperature
****Special solutions available for 90 °C, please consult your distributor
BERNT LORENTZ GmbH
Siebenstuecken 24, 24558 Henstedt-Ulzburg,
Germany, Tel +49 (0)4193 8806-700, www.lorentz.de
Created by LORENTZ COMPASS 3.1.0.134
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.Pictures may differ from actual
products depending on local market requirements and regulations.
Solar Surface Pump System
PSk2-40 CS-G200-24/4
7. NPSH
Pump Chart Vmp* 575 V
*Vmp: MPP-voltage under Standard Test Conditions (STC): 1000 W/m² solar irradiance, 25 °C cell temperature
The NPSH (Net Positive Suction Head) is NOT the operating suction head. To calculate the operating suction head please refer to the
installation manual.
BERNT LORENTZ GmbH
Siebenstuecken 24, 24558 Henstedt-Ulzburg,
Germany, Tel +49 (0)4193 8806-700, www.lorentz.de
Created by LORENTZ COMPASS 3.1.0.134
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.Pictures may differ from actual
products depending on local market requirements and regulations.
Solar Surface Pump System
PSk2-40 CS-G200-24/4
8. H =
H1 =
H2 =
W1 =
W2 =
D =
D1 =
500 mm
450 mm
421 mm
320 mm
290 mm
9.0 mm
226 mm
Controller
A =
B =
C =
D =
E =
F =
G =
H =
I =
J =
K =
L =
M =
N =
O =
P =
400 mm
310 mm
660 mm
1,000 mm
270 mm
415 mm
278 mm
219 mm
200 mm
266 mm
295 mm
340 mm
22 mm
400 mm
360 mm
24 mm
Pump Unit
Net weight
Controller 18 kg
Pump Unit 492 kg
Motor 240 kg
Pump End 252 kg
Dimensions and Weights
BERNT LORENTZ GmbH
Siebenstuecken 24, 24558 Henstedt-Ulzburg,
Germany, Tel +49 (0)4193 8806-700, www.lorentz.de
Created by LORENTZ COMPASS 3.1.0.134
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.Pictures may differ from actual
products depending on local market requirements and regulations.
Solar Surface Pump System
PSk2-40 CS-G200-24/4
9. BERNT LORENTZ GmbH
Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany
Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
V180904
Water Sensor
Device for Dry Run Protection in Applications with LORENTZ Solar Surface
Pump Systems
The device can be used to detect the water level in the suction side of the pipeline. When the two
electrodes run dry, the LORENTZ Controller will stop the pump and indicates Source Low LED.
ORDER INFORMATION
• Item no.: 19-000001 product name: Water sensor, pipe inst.
• Item no.: 19-000002 product name: SS adapter
• Item no.: 19-000003 product name: Steel adapter
Pipeline adapter must be ordered separately
(available as steel or stainless steel version)
FEATURES
• Reliable dry run protection
• Trouble free operation
TECHNICAL DATA
• Max. operating temperature 70 °C
• Enclosure class: IP54
• Cable length: 4 m
• Wire size: 2x 1.0mm² or AWG 17,
waterproofed
• Mounted in vertical position
• Meets the requirements for CE
DIMENSION/WEIGHT
• Packaging dimensions: 180 x 180 x 80 mm
7.1 x 7.1 x 3.1in
• Total weight: 3.5kg / 7.7lbs
pipeline adapter
10. BERNT LORENTZ GmbH
Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany
Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
V180904
Float Switch
Mechanically Activated Device for Water Level Detection in Applications
with LORENTZ Solar Pump Systems
The switch can be used to detect the water level within a tank. When the water level in the tank
reaches the maximum, the LORENTZ Controller will stop the pump and indicates Tank Full LED.
ORDER INFORMATION
• Item no.: 19-000030 product name: Float Switch
FEATURES
• N.O. (normally open) and N.C. (normally closed) function
• Reliable water level detection
• Simple to install
• Trouble free operation
• Not sensitive to rotation
• Corrosion-free
TECHNICAL DATA
• Operating temperature: -10°C to 55°C
• Storage temperature: : -10°C to 55°C
• Enclosure class: IP68
• Cable length: 3m, waterproof
• Wire size: 3x 1.0mm² or AWG 18
• Meets the requirements for CE
DIMENSION/WEIGHT
• Packaging dimensions: 230 x 160 x 55 mm
9.1 x 6.3 x 2.2 in
• Total weight: 0.8 kg / 1.8 lbs
11. BERNT LORENTZ GmbH
Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany
Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
V180904
Surge Protector
Device to Protect LORENTZ Pump Accessories from Voltage Spikes
ORDER INFORMATION
• Item no.: 19-000280 product name: Surge Protector
FEATURES
• Reliable surge protection for all
LORENTZ pump accessories
• Can be installed inside the PS Controller
TECHNICAL DATA
• Max. voltage: 14 VDC
• Max current 8/20µs: 500 A
• Enclosure class: IP65
• Ambient temperature: max. 50°C
• Wire size: 2x 1.5mm² or AWG 16
• Meets the requirements for CE
DIMENSION/WEIGHT
• Packing dimensions: 70 x 45 x 20 mm
2.8 x 1.8 x 0.8 in
• Total weight 0.1 kg / 0.2 lbs
12. BERNT LORENTZ GmbH Co. KG
Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany
Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on
local market requirements and regulations
V150528
PV Disconnect 1000-40-5
Five string connection box with DC Disconnect Switch
ORDER INFORMATION
Item no.: 19-000115
Product name: PV Disconnect 1000-40-5
FEATURES
Simple and cost effective unit to connect
up to five module strings
Includes an appropriate DC rated disconnect switch
Designed for PSk2 / PSk pump systems
Used as part of a professional system installation
TECHNICAL DATA
Wiring of up to 5 PV-strings in parallel
DC rated disconnect switch enclosed
Enclosure class IP 54
Meets the requirements for CE
PV Disconnect 1000-40-5
Max. voltage
1,000 V DC (Uoc)
880 V DC (Ump)
Max. current per string 40 A
Max. total current 40 A
Max. no. of strings 5
String cable size 4 - 10mm²
Output cable size 4 - 16mm²
RELATED PRODUCTS
PV Combiner 1000-125-4
Connection Box for parallel wiring of two or
more PV Disconnect 1000-40-5
Item no.: 19-000116
PV Protect 1000-125
Surge protection device for PV systems
Item no.: 19-000117
DIMENSION/WEIGHT [mm]
Net. Weight: 2,50kg
PG cable glands
(2x PG11 10x M16)
13. BERNT LORENTZ GmbH
Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany
Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on
local market requirements and regulations
V180904
PV Combiner 1000-125-4
Connection box for parallel wiring
ORDER INFORMATION
• Item no.: 19-000116
• Product name: PV Combiner 1000-125-4
FEATURES
• Designed for PSk pump systems
• For professional installation of pumping
Systems
TECHNICAL DATA
• Wiring for up to 4 input-strings in parallel
• Combine two or
more PV Disconnect 1000-40-5 units
• Enclosure class IP 54
• Meets the requirements for CE
PV Combiner 1000-125-4
Max. voltage 1,000 V DC
Max. current per string 125 A
Max. total current 125 A
Max. no. of strings 4
String cable size 10 - 35mm²
Output cable size 10 - 35mm²
RELATED PRODUCTS
PV Disconnect 1000-40-5
• Five string connection box with DC Disconnect
Switch
• Item no.: 19-000115
PV Protect 1000-125
• Surge protection device for PV systems
• Item no.: 19-000117
DIMENSION/WEIGHT [mm]
Net. Weight: 2,0kg
PG cable glands
(10x PG16)
14. BERNT LORENTZ GmbH
Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany
Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice. Pictures may differ from actual products depending on
local market requirements and regulations
V180904
PV Protect 1000-125
Surge protective device for PV systems
ORDER INFORMATION
• Item no.: 19-000117
• Product name: PV Protect 1000-125
FEATURES
• Provides enhanced level of protection to the PSk
controller from electrical surges (indirect lightning)
• Designed for PSk2 / PSk pump systems
• Used as part of a professional system installation
• Installed on the DC input line close to pump controller
• Requires a reliable ground connection to operate
TECHNICAL DATA
• Connects between PV Generator and Controller
• Enclosure class IP 54
• Meets the requirements for CE
PV Protect 1000-125
Max. voltage 1,000 V DC
Max. current 125 A
Input cable size 10 - 35mm²
Output cable size 10 - 35mm²
Grounding cable size 16 mm²
RELATED PRODUCTS
PV Disconnect 1000-40-5
• Five string DC connection box with DC discon-
nect
• Item no.: 19-000115
PV Combiner 1000-125-4
• Combiner box for parallel wiring of two or
more PV Disconnect 1000-40-5 units
• Item no.: 19-000116
DIMENSION/WEIGHT [mm]
Net. Weight: 1,5kg
PG cable glands
(5x PG16)
15. BERNT LORENTZ GmbH
Siebenstuecken 24, 24558 Henstedt-Ulzburg,
Germany,
Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
V181030
SmartPSUk2
AC/DC Converter to Supply PSk2 Pump Systems with Power from a
Generator or Grid Supply
ORDER INFORMATION
• Item no.: 19-002585 Product name: SmartPSUk2
FEATURES
• Provides DC power to PSk2 pump controllers from AC and DC
sources
• Blends solar power (DC) with AC power from the grid or generator
• Part of the PSk2 SmartSolution for hybrid powering of water
pumping systems
• Data link to PSk2 for control and monitoring
• Integrated overheat protection and active cooling
SmartSolution OVERVIEW
16. BERNT LORENTZ GmbH
Siebenstuecken 24, 24558 Henstedt-Ulzburg,
Germany,
Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
V181030
TECHNICAL DATA
• Compatible with PSk2-xx pump controllers (from July 2016)
• 3-Phase AC input
o 380 – 415 V (± 10 %)
o 50 Hz/60 Hz
o max. 38 kW (48 kVA)
• PV max open circuit voltage: 850 V DC
• DC output
o Umax = 850 V DC
o Imax = 70 A
• Enclosure class: IP54, stainless steel powered coated case
• Ambient temperature: -10 to 50°C
PRODUCT CONTENT
The SmartPSUk2 comes with a cable to connect to the PSk2 Controller (1.00 m) and a back plate for
mounting on non-flat surfaces.
STANDARDS
• Meets the requirements for CE
DIMENSION/WEIGHT
• Packing dimensions: 560 x 400 x 340 mm (22.0 x 15.7 x 13.4 in)
• Net weight: 18 kg (39 lbs)
17. BERNT LORENTZ GmbH
Siebenstuecken 24, 24558 Henstedt-Ulzburg, Germany
Tel +49 (0)4193 8806-700, www.lorentz.de
All specifications and information are given with good intent, errors are possible and products may be subject to change without notice.
Pictures may differ from actual products depending on local market requirements and regulations.
V181030
SmartStart
Automatic Remote Diesel Generator Switching Device
The SmartStart can automatically and remotely start and stop diesel generators for hybrid solar
pumping. It has a secondary ancillary output for switching other devices. It connects to the PSk2
Controller and to the remote switch input of the diesel generator.
ORDER INFORMATION
• Item no.: 19-004280 Product name: SmartStart
FEATURES
• Automatically switches on/off diesel engines equipped
with remote start input (NO)
• SmartStart provides power to the PSk2 systems for night time
logic operation such as early morning pump starting
• Battery charging from PSk2 Controller
• Shows system status via LEDs
• Ancillary output for switching other devices
TECHNICAL DATA
• Max. contact rating: 277 V AC / 30 V DC / 3 A
• Enclosure class: IP54
• Nominal cross section for GEN Link cable 1.5 mm²
• Further information is available in the PSk2 manual on partnerNET
PRODUCT CONTENT
The SmartStart comes with a cable to connect to the PSk2 Controller. (1.50 m) The required battery
must be ordered separately. The battery must meet the following requirements:
• Sealed 12 V AGM lead acid battery Min capacity: 7 Ah
DIMENSION/WEIGHT
• Packaging dimensions: L x W x H 270 x 250 x 230 mm (10.6 x 9.8 x 9.1 in)
• Total weight (without battery): 2.8 kg (6.2 lbs)
• Battery case: L x W x H 151 x 70 x 95 mm (5.94 x 2.56 x 3.74 in)