Thermal Resistance Approach to Analyze Temperature Distribution in Hollow Cylinders Made of Functionally Graded Material (FGM): Under Dirichlet Boundary Condition
Thermal Resistance Approach to Analyze Temperature Distribution in Hollow Cylinders Made of Functionally Graded Material (FGM): Under Dirichlet Boundary Condition
The document proposes a thermal resistance approach (TRA) to analyze the temperature distribution in hollow cylinders made of functionally graded materials (FGMs) under Dirichlet boundary conditions. The TRA models the FGM cylinder as a thermal resistance network to bypass the non-linearity introduced by the power-law variation of thermal conductivity. Results from the TRA are found to match previous analytical and numerical solutions with less than 0.000012% average error. The TRA can determine temperature profiles for any material gradient distribution and provides insights into tailoring material gradients for desired temperature or stress fields.
Structural Changes in the Surface Layer of Deep Rolled Samples Due to Thermal...
Similar to Thermal Resistance Approach to Analyze Temperature Distribution in Hollow Cylinders Made of Functionally Graded Material (FGM): Under Dirichlet Boundary Condition
Radial Heat Transport in Packed Beds-III: Correlations of Effective Transport...inventionjournals
Similar to Thermal Resistance Approach to Analyze Temperature Distribution in Hollow Cylinders Made of Functionally Graded Material (FGM): Under Dirichlet Boundary Condition (20)
The Most Attractive Pune Call Girls Budhwar Peth 8250192130 Will You Miss Thi...
Thermal Resistance Approach to Analyze Temperature Distribution in Hollow Cylinders Made of Functionally Graded Material (FGM): Under Dirichlet Boundary Condition
1. Thermal Resistance Approach to
Analyze Temperature Distribution in
Hollow Cylinders Made of
Functionally Graded Material (FGM):
Under Dirichlet Boundary Condition
S M Shayak Ibna Faruqui
Abul Al Arabi &
M. S. Parvej
Bangladesh University of Engineering and Technology
2. Introduction to FGMs
• FGMs are superior composites with better performance.
• Continuous spatial distribution of 2 or more material in 1 ,2 or 3 directions.
• Scope of tailoring material property according to desire.
0
20
40
60
80
100
0 0.5 1
VolumeFraction
Thickness
Volume Fraction A
Volume Fraction B
5. Historical Background
• First introduced in Japan during 1984-85.
• Challenge was finding a particular solution material which
could withstand a massive temperature gradient of 1000℃
with a 10mm thickness.
6. Problem with Traditional materials
and Composites
• In high temperature gradient condition they both fail.
Metals Buckle Composite Delaminates
8. Example of some Extreme Thermal Environment
Nuclear Reactor
Exhaust nozzle of rocketReentry Module
9. Types of FGMs
• Depends on material gradient which follows a
particular function.
1. pFGM: material distribution follows a power function
2. sFGM: material distribution follows sigmoid function
3. eFGM: material distribution follows an exponential
function
10. This Work: Motivation and Goals
• Introducing a new approach (TRA) to solve
temperature distribution in a Hollow FGM Cylinder.
• Bypassing problems caused by “Non-linearity” of
material gradient.
• Obtaining results analytically and applying FEM and
compare with TRA
11. 𝑘 𝑜
𝑘𝑖
𝐾𝑓𝑔𝑚
𝑇𝑜
𝑇𝑖
This Work: Formulation of problemBoundaryCondition
A hollow cylinder is considered with an inner radius 𝑟𝑖 and outer radius 𝑟𝑜
where 𝑘𝑖 and 𝑘 𝑜 are the value of thermal conductivity at inner and outer
surfaces respectively. Thermal conductivity is assumed to vary from 𝑘𝑖 to 𝑘 𝑜
along radial direction following a Power Function where “n” is the
power law index.
13. This Work: Governing Equation
Heat Conduction Equation in Cylindrical Co-ordinate:
14. This Work: Governing Equation
Heat Conduction Equation in Cylindrical Co-ordinate:
Due to symmetry & Steady State:
∂ 𝑇
∂φ
= 0 ,
∂ 𝑇
∂ 𝑧
=0 and
∂ 𝑇
∂ 𝑡
= 0
No Internal Heat
Generation
15. This Work: Governing Equation
The governing equation yields to:
𝑑
𝑑𝑟
𝐾𝑓𝑔𝑚 𝑟 . 𝑟
𝑑𝑇
𝑑𝑟
= 0
𝐾𝑓𝑔𝑚 𝑟 = 𝑘𝑖 + 𝑘 𝑜 − 𝑘𝑖
𝑟 − 𝑟𝑖
𝑟𝑜 − 𝑟𝑖
𝑛
• Thermal conductivity, K is not constant
• Follows power function of independent variable r
16. This Work: Governing Equation
The governing equation yields to:
𝑑
𝑑𝑟
𝐾𝑓𝑔𝑚 𝑟 . 𝑟
𝑑𝑇
𝑑𝑟
= 0
𝐾𝑓𝑔𝑚 𝑟 = 𝑘𝑖 + 𝑘 𝑜 − 𝑘𝑖
𝑟 − 𝑟𝑖
𝑟𝑜 − 𝑟𝑖
𝑛
• Thermal conductivity, K is not constant
• Follows power function of independent variable r
Power Law Index
18. This Work: Literature Review
1. S. Karampour et al. [2] solved the heat conduction equation for obtaining
temperature distribution analytically using Legendre polynomials and
Euler differential equations system.
2. Celebi et al. [3] used Complimentary Function Method (CFM) to convert
the boundary value problem into an initial value problem and solved the
temperature problem.
3. M. Jabbari et al. [4], [5], [6], [7] & [8] obtained results for temperature
distribution directly by exact method and as he assumed the radial
distribution of material property to follow an exponential function, getting
exact solutions posed no complexity.
4. X.L. Peng et al. [9] also converted the boundary value problem associated
with the thermoelastic problem into a Fredholm integral equation and by
numerically solving the resulting equation, the distribution of the
temperature was obtained.
5. Shao Z.S [10] presented a study about mechanical and thermal stresses in
FGM hollow cylinder of finite length and Zimmerman et al [11] in
uniformly heated FGM cylinder.
19. This Work: Analytical Solution
For n=1 Integrating twice the solution yields,
It’s a 1st Order linear homogeneous ODE
𝑑
𝑑𝑟
𝐾𝑓𝑔𝑚 𝑟 . 𝑟
𝑑𝑇
𝑑𝑟
= 0
𝑇 𝑟 =
(𝑟𝑜 − 𝑟𝑖)𝐶1
𝑟𝑜 𝐾𝑜 − 𝑟𝑖 𝐾𝑖
𝑙𝑛
𝑟 𝐾𝑖 − 𝐾𝑜
𝐾𝑖 𝑟𝑜 − 𝑟 + 𝐾𝑜 𝑟 − 𝑟𝑖
+ 𝐶2
• 𝐶1 & 𝐶2 is integration constants.
20. This Work: Analytical Solution
For n=1 Integrating twice the solution yields,
It’s a 1st Order linear homogeneous ODE
𝑑
𝑑𝑟
𝐾𝑓𝑔𝑚 𝑟 . 𝑟
𝑑𝑇
𝑑𝑟
= 0
𝑇 𝑟 =
(𝑟𝑜 − 𝑟𝑖)𝐶1
𝑟𝑜 𝐾𝑜 − 𝑟𝑖 𝐾𝑖
𝑙𝑛
𝑟 𝐾𝑖 − 𝐾𝑜
𝐾𝑖 𝑟𝑜 − 𝑟 + 𝐾𝑜 𝑟 − 𝑟𝑖
+ 𝐶2
• It can be marked that the solution is valid if
𝐾 𝑜
𝐾 𝑖
≠
𝑟 𝑖
𝑟 𝑜
.
• 𝐶1 & 𝐶2 is integration constants.
31. Thermal Resistance Approach: Advantages
S-FGMP-FGM E-FGM
• Can be used for any type of material gradient.
• Gives you temperature profile for any kind of material
distribution when analytical solution is very complex.
• Helps to visualize the effect of material gradient
32. Thermal Resistance Approach: Future Scopes
• Determining material gradient for a desired stress profile
• Tailoring material gradient for desired temperature field
• Tailoring material gradient for desired stress field
33. Thermal Resistance Approach: Future Scopes
• Determining material gradient for a desired stress profile
• Tailoring material gradient for desired temperature field
• Tailoring material gradient for desired stress field