The document provides an overview of dimensional analysis and its applications in fluid mechanics. Dimensional analysis is a tool used to correlate analytical and experimental results and predict prototype behavior from model measurements. It involves identifying the fundamental dimensions of variables (e.g. mass, length, time) and establishing dimensionless relationships between variables using methods like Rayleigh's or Buckingham's π-theorem. Dimensional analysis is important for model analysis where dynamic similarity between a model and prototype must be achieved. The document discusses different model laws used to design models for similarity based on dominant forces like viscosity, gravity, etc. It also provides scale ratios required for geometric, kinematic and dynamic similarity.
2. 1. Introduction to Dimensions & Units
2. Use of DimensionalAnalysis
3. Dimensional Homogeneity
4. Methods of DimensionalAnalysis
5. Rayleigh’s Method
3. 6. Buckingham’s Method
7. Model Analysis
8. Similitude
9. Model Laws or Similarity Laws
10. Model and Prototype Relations
4. Many practical real flow problems in fluid mechanics can be solved by using
equations and analytical procedures. However, solutions of some real flow
problems depend heavily on experimental data.
Sometimes, the experimental work in the laboratory is not only time-consuming,
but also expensive. So, the main goal is to extract maximum information from
fewest experiments.
In this regard, dimensional analysis is an important tool that helps in correlating
analytical results with experimental data and to predict the prototype behavior from
the measurements on the model.
5. In dimensional analysis we are only concerned with the nature of the
dimension i.e. its quality not its quantity.
Dimensions are properties which can be measured.
Ex.: Mass, Length, Time etc.,
Units are the standard elements we use to quantify these dimensions.
Ex.: Kg, Metre, Seconds etc.,
The following are the Fundamental Dimensions (MLT)
Mass
Length
kg
m
M
L
Time s T
6. Secondary dimensions are those quantities which posses more than one
fundamental dimensions.
1. Geometric
a) Area
b) Volume
m2
m3
L2
L3
2. Kinematic
a) Velocity
b) Acceleration
3. Dynamic
m/s
m/s2
L/T
L/T2
L.T-1
L.T-2
a) Force N ML/T M.L.T-1
b) Density kg/m3 M/L3 M.L-3
7. Find Dimensions for the following:
1.Stress / Pressure
2.Work
3.Power
4.Kinetic Energy
5.Dynamic Viscosity
6.Kinematic Viscosity
7.Surface Tension
8.Angular Velocity
9.Momentum
10.Torque
8. 1. Conversion from one dimensional unit to another
2. Checking units of equations (Dimensional
Homogeneity)
3. Defining dimensionless relationship using
a) Rayleigh’s Method
b) Buckingham’s π-Theorem
4. Model Analysis
10. To define relationship among variables
This method is used for determining the
expression for a variable which depends upon
maximum three or four variables only.
11. To define relationship among variables
This method is used for determining the
expression for a variable which depends upon
maximum three or four variables only.
Methodology:
Let X is a function of X1 ,X2, X3 and mathematically it can be written as
X = f(X1, X2, X3)
This can be also written as
X = K (X1
a , X2
b ,X3
c ) where K is constant and a, b and c are arbitrarily powers
The values of a, b and c are obtained by comparing the powers of the fundamental
dimension on both sides.
12. To define relationship among variables
This method is used for determining the
expression for a variable which depends upon
maximum three or four variables only.
Methodology:
Let X is a function of X1 ,X2, X3 and mathematically it can be written as
X = f(X1, X2, X3)
This can be also written as
X = K (X1
a , X2
b ,X3
c ) where K is constant and a, b and c are arbitrarily powers
The values of a, b and c are obtained by comparing the powers of the fundamental
dimension on both sides.
Problem: Find the expression for Discharge Q in a open channel flow when Q is
depends on Area A and VelocityV.
Solution:
Q = K.Aa.Vb 1
where K is a Non-dimensional constant
Substitute the dimensions on both sides of equation 1
M0 L3 T-1 = K. (L2)a.(LT-1)b
Equating powers of M, L, T on both sides,
Power of T,
Power of L,
-1 = -b b=1
3= 2a+b 2a = 2-b = 2-1 = 1
Substituting values of a, b, and c in Equation 1m
Q = K. A1. V1 = V.A
13. To define relationship among variables
This method is used for determining the
expression for a variable which depends upon
maximum three or four variables only.
Rayeligh’s Method
Methodology:
Let X is a function of X1 ,X2, X3 and mathematically it can be written as
X = f(X1, X2, X3)
This can be also written as
X = K (X1
a , X2
b ,X3
c ) where K is constant and a, b and c are arbitrarily powers
The values of a, b and c are obtained by comparing the powers of the fundamental
dimension on both sides.
14. To define relationship among variables
This method is used for determining the
expression for a variable which depends upon
maximum three or four variables only.
Rayeligh’s Method
Methodology:
Let X is a function of X1 ,X2, X3 and mathematically it can be written as
X = f(X1, X2, X3)
This can be also written as
X = K (X1
a , X2
b ,X3
c ) where K is constant and a, b and c are arbitrarily powers
The values of a, b and c are obtained by comparing the powers of the fundamental
dimension on both sides.
15. This method of analysis is used when number of variables are more.
Theorem:
If there are n variables in a physical phenomenon and those n variables contain m dimensions,
then variables can be arranged into (n-m) dimensionless groups called Φ terms.
Explanation:
If f (X1, X2, X3, ……… Xn) = 0 and variables can be expressed using m dimensions then
f (π1, π2, π3, ……… πn - m) = 0 where, π1, π2, π3, … are dimensionless groups.
Each π term contains (m + 1) variables out of which m are of repeating type and one is of non-
repeating type.
Each π term being dimensionless, the dimensional homogeneity can be used to get each π term.
π denotes a non-dimensional parameter
16. Selecting Repeating Variables:
1. Avoid taking the quantity required as the repeating variable.
2. Repeating variables put together should not form dimensionless group.
3. No two repeating variables should have same dimensions.
4. Repeating variables can be selected from each of the following
properties.
Geometric property Length, height, width, area
Flow property Velocity, Acceleration, Discharge
Fluid property Mass density, Viscosity, Surface tension
20. For predicting the performance of the hydraulic structures (such as dams, spillways
etc.) or hydraulic machines (such as turbines, pumps etc.) before actually
constructing or manufacturing, models of the structures or machines are made and
tests are conducted on them to obtain the desired information.
Model is a small replica of the actual structure or machine
The actual structure or machine is called as Prototype
Models can be smaller or larger than the Prototype
Model Analysis is actually an experimental method of finding solutionsof
complex flow problems.
21. Similitude is defined as the similarity between the model and prototype in
every aspect, which means that the model and prototype have similar
properties.
Types of Similarities:
1. Geometric Similarity Length, Breadth, Depth, Diameter,Area,
Volume etc.,
2. Kinematic Similarity Velocity, Acceleration etc.,
3. Dynamic Similarity Time, Discharge, Force, Pressure Intensity,
Torque, Power
22. The geometric similarity is said to be exist between the model and
prototype if the ratio of all corresponding linear dimensions in the model
and prototype are equal.
L B D r
m m m
LLP
BP
DP
r
2
L
AP
Am
r
3
L
VP
Vm
where Lr is ScaleRatio
23. The kinematic similarity is said exist between model and prototype if the
ratios of velocity and acceleration at corresponding points in the model and
at the corresponding points in the prototype are the same.
VP
Vm
Vr
aP
am
ar
whereVr isVelocity Ratio where ar is Acceleration Ratio
Also the directions of the velocities in the model and prototype should be same
24. The dynamic similarity is said exist between model and prototype if the
ratios of corresponding forcesacting at the corresponding points are
equal
FP
Fm
Fr
where Fr is Force Ratio
Also the directions of the velocities in the model and prototype should be same
It means for dynamic similarity between the model and prototype, the
dimensionless numbers should be same for model and prototype.
25. 1. Inertia Force, Fi
It is the product of mass and acceleration of the flowing fluid and acts in the
direction opposite to the direction of acceleration.
It always exists in the fluid flow problems
26. 1. Inertia Force, Fi
2. Viscous Force, Fv
It is equal to the product of shear stress due to viscosity and surface area of the
flow.
27. 1. Inertia Force, Fi
2. Viscous Force, Fv
3. Gravity Force, Fg
It is equal to the product of mass and acceleration due to gravity of the flowing
fluid.
28. 1. Inertia Force, Fi
2. Viscous Force, Fv
3. Gravity Force, Fg
4. Pressure Force, Fp
It is equal to the product of pressure intensity and cross sectional area of
flowing fluid
29. 1. Inertia Force, Fi
2. Viscous Force, Fv
3. Gravity Force, Fg
4. Pressure Force, Fp
5. Surface Tension Force, Fs
It is equal to the product of surface tension and length of surface of the flowing
30. 1. Inertia Force, Fi
2. Viscous Force, Fv
3. Gravity Force, Fg
4. Pressure Force, Fp
5. Surface Tension Force, Fs
6. Elastic Force, Fe
It is equal to the product of elastic stress and area of the flowing fluid
31. V
Lg
InertiaForce
Gravity Force
Dimensionless numbers are obtained by dividing the inertia force by
viscous force or gravity force or pressure force or surface tension forceor
elastic force.
1. Reynold’s number, Re =
2. Froude’s number, Fe =
3. Euler’s number, Eu =
e4. Weber’s number, W =
V
p/
InertiaForce
PressureForce
InertiaForce V
SurfaceTensionForce / L
Viscous Force
Inertia Force
VL
or
VD
Inertia Force
V
Elastic Force C
36. The laws on which the models are designed for
dynamic similarityare
called model laws or laws of similarity.
1. Reynold’s Model
Models based on Reynolds’s Number includes:
a) Pipe Flow
b) Resistance experienced by Sub-marines, airplanes, fully immersed bodies
37. The laws on which the models are designed for dynamic similarity are
called model laws or laws of similarity.
1. Reynold’s Model
2. Froude Model Law
Froude Model Law is applied in the following fluid flow problems:
a) Free Surface Flows such as Flow over spillways, Weirs, Sluices, Channels
etc.,
b) Flow of jet from an orifice or nozzle
c) Where waves are likely to formed on surface
d) Where fluids of different densities flow over one another
38. The laws on which the models are designed for dynamic similarity are
called model laws or laws of similarity.
1. Reynold’s Model
2. Froude Model Law
3. Euler Model Law
Euler Model Law is applied in the following cases:
a) Closed pipe in which case turbulence is fully developed so that viscous forces
are negligible and gravity force and surface tension is absent
b) Where phenomenon of cavitations takes place
39. The laws on which the models are designed for
dynamic similarityare
called model laws or laws of similarity.
1. Reynold’s Model
2. Froude Model Law
3. Euler Model Law
4. Weber Model LawWeber Model Law is applied in the following cases:
a) Capillary rise in narrow passages
b) Capillary movement of water in soil
c) Capillary waves in channels
d) Flow over weirs for small heads
40. The laws on which the models are designed for dynamic similarity are
called model laws or laws of similarity.
1. Reynold’s Model
2. Froude Model Law
3. Euler Model Law
4. Weber Model Law
5. Mach Model Law
Mach Model Law is applied in the following cases:
a) Flow of aero plane and projectile through air at supersonic speed ie., velocity
more than velocity of sound
b) Aero dynamic testing, c) Underwater testing of torpedoes, and
d) Water-hammer problems
41. If the viscous forces are predominant, the models are designed fordynamic
similarity based on Reynold’s number.
p
P PP
m
m mm V LρV Lρ
V
L
t r
r
r
TimeScaleRatio
Velocity, V = Length/Time T = L/V
t
a
r
Vr
r
Acceleration ScaleRatio
Acceleration, a = Velocity/Time L =V/T
R Ree pm
42.
43.
44. If the gravity force is predominant, the models are designed fordynamic
similarity based on Froude number.
LrTr
ScaleRatioforTime
g Lm g LP
m p
Vm
Vp
LrVr
VelocityScaleRatio F Fee pm
Tr
Scale Ratio for Accele ration 1
r
2.5
Q Scale Ratio for Discharge Lr
3
Fr
Scale Ratio for Force Lr
Fr
Scale Ratio for Pressure Intensity Lr
3.5
Pr
Scale Ratio for Power Lr
45.
46.
47.
48.
49.
50.
51. Chapter 12
A Textbook of Fluid Mechanics and
Hydraulic Machines
Dr. R. K. Bansal
Laxmi Publications