4. b The air powered SM 8 mini-
beveler is a rugged portable
weld-end preparation tool. It will
perform repeatable quality weld
preps on most metal pipes and
tubes including stainless steel,
from 8 mm I.D. to 32 mm O.D.
The cutting head will bevel, face
and counterbore individually or
in a synchronized operation.
b The SM 8 is easy to install on
all pipes and completely torque
accepting (requires no holding
device for machining).
b The Protem SM 8 unit requires only 32 mm total clearance thereby
allowing precise machining within very restricted working areas.
TYPE SM8
PIPE BEVELING MACHINE
TECHNICAL SPECIFICATIONS
Standard Mandrel I.D.
clamping capacity
ID range: 8 mm to 30.5 mm I.D.
Machining range All pipe and tube sizes from 8 mm I.D. to 32 mm O.D.
Tool feed Manual handwheel, 10 mm travel
Weight Complete unit 1.2 kg
Motor drive 0.5 HP - 6 bars - 500 l/mn
Cutting head gear drive off-load speed: 120 rpm
nominal speed: 60 rpm
Tooling Facing, 30 and 37°30’ bevel, counterbore, J-bevel (All
other angles available on request]
Mandrels Various socket rods, socket holders, expansion sockets
are available according to diameters to perform
Optional equipment Miling head
DIMENSIONS
Ø36.5
32
32
166.5
244
5. b The air powered S 18
beveling machine is a rugged
portable weld-end prepa-
ration lathe. It will perform
repeatable quality weld
preps on most metal pipes
including stainless steel,
from 0.70” to 1.72” I.D.
(18 mm to 42 mm O.D.).
The S 18 will bevel, face and
counterbore individually or in
a synchronized operation.
b The S 18 is easy to install
on all pipes and completely torque accepting (requires no holding
device during machining).
b The PROTEM S 18 unit requires only 42 mm minimum clearance,
thereby allowing precise machining within very restricted working
areas.
S 18
PIPE BEVELING MACHINE
Clamping capacity ID range: 18 mm I.D. to 43.75 mm I.D.
Machining capacity 18 mm I.D. to 42 mm O.D.
Tool rotation Off load: 200 rpm
Weight 9.8 pounds (2 kg)
Feed 35 mm
Drive Pneumatic 0.5 HP - 6 bars - 500 l/mn
Optional equipment Right angle feed Lever feed
Auto clamping (see SIBCA)
Milling head
DIMENSIONS
TECHNICAL SPECIFICATIONS
257
Ø42
127
190
42
6. b The US 25 portable pipe
beveling tool is designed for
beveling and facing pipe from
0.98” (25 mm) I.D. to 3” O.D.
(107 mm) and 4.72” O.D.
(88.9 mm), (optional mandrels
are available for I.D. sizes down
to 0.48” (12 mm).
b The US 25 features self-ac-
cepting torque system and an
integral drive motor (several
drive motor options and gear
ratios are available). Standard tool plates will accept multiple tool bits
allowing up to four simultaneous machining operations. Such opera-
tions may include beveling, facing, counterboring, compound beveling
and O.D. chamfering.
b The rugged US 25 is capable of performing repeatable high quality
weld preparations on all machinable alloy pipes, including stainless
steel and other high nickel alloys.
US 25
PIPE BEVELING MACHINE
TECHNICAL SPECIFICATIONS
Standard Mandrel I.D.
clamping range capacity
I.D. range: 25-107 mm
Mandrel engagement length: 63.5 mm
Mandrel expansion: 10 mm
Optional mandrel # 1 I.D. range: 12-17 mm
Optional mandrel # 2 I.D. range: 18-26 mm
Machining range Standard tool holder: 12-90 mm
Optional 2 in. Tool holder: 12-60 mm O.D.
Optional 4 in. Tool holder: 12-120 mm O.D.
Tool feed Manual travel: 35 mm
Tool rotation Off load speed: 150 rpm (standard motor)
Maximum nominal speed: 70 rpm (standard motor)
Weight 8 pounds (3.6 kg) with standard motor
Motor drive Standard pneumatic drive: .98 hp. 32 cfm at 90 psi
Optional electric drive: 1.6 hp. 110 V or 240 V 1200 W
Optional pneumatic drive: 2 hp. 64 cfm at 90 psi
DIMENSIONS
7. 35.07
86.5A
R225.68
12.1
239.68
b The S 18 CA / US 25 CA
portable pipe beveling
tools are designed for high
quality beveling, facing and
machining on pipe and tube.
b The main plus of
these machines is their
clamping system into
the tube by simply acting
on a pneumatic on/off
distributor which allows a
clamping in 2 seconds only.
b The standard tool plate will accept up to 4 tool bits allowing to face
bevel and counterbore simultaneously. Once preset for large series or
repetitive work, the S18 CA / US 25 CA are capable of performing
repeatable high quality weld preparations on all machinable alloy pipes
including stainless steel…
BEVELING MACHINE WITH AUTOMATIC
CLAMPING - TYPE S 18 CA / US 25 CA
Model S 18 CA US 25 CA
Stroke 12 mm 25 mm
Clamping range Shaft #1: dia. 12 to 24
Shaft #2: dia. 18 to 38
Shaft #1: dia. 18 to 22.5
Shaft #2: dia. 25.4 to 88.9
Machining range 12 mm ID to 30 mm OD
(with shaft #1)
18 mm ID to 24 mm OD
(with shaft #2)
18.8 mm ID to 27.5 mm OD
(with shaft #1)
25.4 mm ID to 88.9 mm OD
(with shaft #2)
Tool rotation 150 rpm 200 rpm
Drive 0.5 HP 1 HP
Air inlet 6 bars - 500 l/min 6 bars - 1200 l/min
Weight 5 kg 7 kg
Optional equipment - Balancer
- Machining limit stop
- Air exhaust
- Balancer
- Milling cutter
- Machining limit stop
- Air exhaust
DIMENSIONS
TECHNICAL SPECIFICATIONS
137
122.47
Env.265.5
376
22
A
25.3
8. b The US 18 TP is fully automatic with
a built in control box. This control box
allows the clamping of the machine,
the rotation of the tool holder, and the
feed of the tool just by pressing a single
switch. The rpm as well as the feed
rate can be adjusted.
b The US 18 TP will perform bevels,
tube facing, weld prep on tube sheet for
the manufacturing or the maintenance.
It also features a machining limit stop
and can be equipped with a positioning
limit stop
AUTOMATIC TUBE TO TUBESHEET FACING
MACHINE US 18 TP
TECHNICAL SPECIFICATIONS
Clamping capacity 12 mm I.D. to 32 mm I.D.
Machining capacity 12 mm I.D. to 38 mm O.D.
RPM w.n. load: 145 rpm
Weight 8 kg
Feed Automatic through a hydraulic cylinder
Feed stroke 20 mm
Drive Pneumatic 0.5 HP
Optional equipment - Machine positioning limit stop
- Balancer
- Steel or Stainless steel carrying case
DIMENSIONS
9. b The US 30 with its reduced
overall dimensions and its
lightweight is specially designed
for applications that have
limited clearance requirements
such as boilers.
b The rugged US 30 model can
face, bevel, counterbore tubes
and pipes from 30 mm I.D. up
to 114 mm O.D. The standard
tool plate will accept multiple
tool bits allowing simultaneous
machining operations.
b The US 30 features a self-accepting torque system and an integral
drive motor. The rugged US 30 is capable of performing repeatable
high quality weld preparations on all machinable alloy pipes including
stainless steel duplex, super duplex, inconel, etc.
LOW CLEARANCE US 30
BEVELING MACHINE - BOILER APPLICATION
TECHNICAL SPECIFICATIONS
Standard Mandrel I.D.
clamping range capacity
I.D. range: 30 mm to 114 mm
Mandrel engagement length: 100 mm
Mandrel expansion: 15 mm
Machining range 30 mm I.D. to 114 mm O.D.
Tool feed (ratchet) Manual travel: 50 mm
Tool rotation Off load speed: 0 to 30 rpm
(other gear ratios available on request)
Weight 22 pounds [10 kg)
Motor drive Standard pneumatic drive: 1 HP
Optional equipment - Flange facing attachment
- Hydraulic drive
- Enveloping jaws (for thin wall tubing and pipe)
- Elbow mandrel assembly
- Auto clamping
- Right angle drive
- 5 tool holder
DIMENSIONS
166.5
395.43
?120
R175.15
80
10. 10
b The US 40 portable pipe
beveling tool is designed for
high quality beveling, facing and
machining on pipe and tube from
43 I.D. to 219 mm O.D. The
standard tool plate will accept
multiple tool bits, allowing up
to four simultaneous machining
operations.
b Such operations may include
beveling, facing, counterboring,
compound beveling and O.D.
chamfering.
b The US 40 features a self-
accepting torque system and an integral drive motor.
b The rugged US 40 is capable of performing repeatable high quality
weld preparations on all machinable alloy pipes including stainless steel
duplex, super duplex, inconel, etc
US 40
PIPE BEVELING MACHINE
TECHNICAL SPECIFICATIONS
Standard Mandrel I.D.
clamping range capacity
ID range: 43 up to 219 mm
Mandrel engagement length: 105 mm
Mandrel expansion: 16 mm
Machining range 43 mm to 219 mm O.D.
Tool feed Standard ratchet tool feed
Manual travel: 50 mm
Tool rotation Off load speed: 0 to 30 rpm
(other gear ratios available on request)
Weight 33 pounds (15 kg)
Motor drive Standard pneumatic drive: 1 HP Optional right angle
pneumatic drive
Optional equipment - Flange facing attachment
- Hydraulic/electric drive
- Enveloping jaws (for thin wall tubing and pipe)
- Elbow mandrel assembly
- ID tracker
- Auto clamping
- Right angle drive
- Copying carriage attachement (see p. 14)
DIMENSIONS
11. 11
b The US 80 is a heavy duty
portable pipe beveling tool
designed for high quality
beveling, facing and machining
on pipe and tube from 80 mm
I.D. to 355 mm O.D.
b Each standard tool plate
accepts multiple tool bits
allowing up to four simultaneous
machining operations. Such
operations may include beveling,
facing, counterboring, compound beveling and O.D. chamfering on
heavy wall materials.
b The US 80 features a self-accepting torque system and an integral
drive motor.
b The rugged US 80 is capable of performing repeatable high quality
weld preparations on all machinable alloy pipes, including stainless
steel and other high nickel alloys
US 80
PIPE BEVELING MACHINE
TECHNICAL SPECIFICATIONS
Standard Mandrel I.D.
clamping capacity
ID range: 80 to 355 mm
Mandrel engagement length: 159 mm
Mandrel expansion: 25 mm
Machining range 80 to 355 mm O.D.
Tool feed Manual travel: 60 mm
Tool rotation Off load speed: 0-30 rpm
Weight 66 pounds (30 kg) with standard motor
Motor drive Standard pneumatic drive: 2 HP 64 cfm at 90 psi
Optional equipment - Hydraulic drive
- Flange facing attachment
- Elbow mandrel assembly
- Copying carriage attachement (see p. 14)
DIMENSIONS
12. 12
b The US 150 portable pipe
beveling tool is designed for
high quality beveling, facing and
machining on pipe and tube
from 5.9” I.D. (150 mm) to
20” O.D. (508 mm).
b The standard tool plate
will accept multiple tool
bits, allowing up to four
simultaneous machining
operations. Such operations
may include beveling, facing counterboring, compound beveling and
O.D. chamfering.
b The US 150 features a self-accepting torque system and an integral
dual right angle pneumatic drive.
b The rugged US 150 is capable of performing repeatable high quality
weld preparations on all machinable alloy pipes including stainless
steel, duplex, superduplex, inconel, etc.
US 150
PIPE BEVELING MACHINE
TECHNICAL SPECIFICATIONS
Standard Mandrel I.D.
clamping range capacity
I.D. range: 150 up to 508 mm
Mandrel engagement length: 212 mm
Mandrel expansion: 30 mm
Machining range 150 mm to 508 mm O.D.
Tool feed Manual travel: 100 mm
Tool rotation Off load speed: 0 - 7 rpm
(other gear ratios available on request)
Weight 200 pounds (90 kg)
Motor drive Dual right angle pneumatic drive 2 x 2.5 HP
Optional equipment - Hydraulic drive
- Flange facing attachment
- Elbow mandrel assembly
- Kit 24”
- Copying carriage attachement (see p. 14)
DIMENSIONS
13. 13
b This new generation elbow
mandrel assembly allows to
position a US type machine
on all types of elbows.
b Its adjustment will be
concentric thanks to the
rules located around the
system, and will allow to
achieve a high quality weld
preparation on all types
of elbows and materials
including stainless steel and
other high nickel alloys
ELBOW MANDREL ASSEMBLY
FOR US SERIES
TECHNICAL SPECIFICATIONS
Set up time 2 minutes
Graduations of the rules Length: 40 mm
Graduation: 0.5 mm
Optional equipment - Stainless steel screws
- Stainless steel additional jaws
DIMENSIONS
Overall dimensions
model A
(mm)
B
(mm)
C
(mm)
US 40 58.98 139 100
US 80 85.44 166 140
US 150 177.86 253 140
Machining capacity
model inside
diameter (mm)
outside
diameter (mm)
US 40 145 219
US 80 170 356
US 150 261 508
14. 14
b The US 40, US 80 US 150 portable pipe bevelling machines, can
be equipped with a copying carriage attachment.
The device can perform bevel on heavy wall, by using a template at the
shape of the welding preparation, and highly improve the capacity of
the standard machines.
b Clamping spiders have to be used to reach the diameters over the
standard clamping capacity of the machine.
b The machines have to be hydraulic driven with a 4 kW or 5.5 kW
Protem hydraulic power pack.
CC SERIES
COPYING CARRIAGE
TECHNICAL SPECIFICATIONS
Model US 40 CC US 80 CC US 150 CC
Working capacity 2” - 12” 4” - 24” 6” - 30”
option 36”
other specifications: see US 40 (p. 9), US 80 (p. 10), US 150 (p. 11).
15. 15
b These hydraulic power packs
have been specially designed
for PROTEM (for the US and
TTNG machine series).
b They are equipped with an
electric remote control, and a
powerful air cooling system.
b They have a fixed flow rate.
A pressure gauge enables
clear visualisation of the
pressure and they are fitted
with a rotation direction
inverter.
b Their dimensions make them easy to transport and being user-
friendly and rapid, they are intended for multiple uses on diverse sites.
b They are supplied with flexible hoses equipped with non-spill type flush
faced Quick Disconnect couplings.
HYDRAULIC POWER PACKS HPP 040 and
HPP 050
Model HPP 040 HPP 050
Power 4 KW single pump
Direct start up
5,5 KW single pump
Direct start up
Voltage 400 V 50/60 Hz 400 V 50 Hz
Circuit Rotation Fixed Flow Rate : 23 L/min Fixed Flow Rate : 33 L/min
Dual Rotation Direction
Pressure Max : 90 Bars Max : 90 Bars
Hoses Length : 5 metres Length : 5 metres
Weight 125 kg 140 kg
Packaging Wooden case Wooden case
Oil volume 20 L 45 L
Oil Type S46HV ISO VG46 S46HV ISO VG46
Options - 15 m of flexible hoses
- Oil sump
- Remote control
- Others: please consult us.
- 15 m of flexible hoses
- Oil sump
- Remote control
- Others : please consult us.
TECHNICAL SPECIFICATIONS
DIMENSIONS
680 mm 450 mm
1050 mm
16. 16
b The TT NG series pipe
severing and beveling machines
will sever and bevel in line pipe
simultaneously.
b This rugged equipment is
easy and safe to operate. High
speed tool steel cutting bits
provide accurate weld joint
machining while eliminating
flame cutting and grinding
procedures.
b A variety of weld joint designs
can be accomplished including
square sever, double bevel, J
bevel counterbore, compound
bevel and socket weld removal
TUBE CUTTING AND BEVELING MACHINE
TTNG SERIES
TECHNICAL SPECIFICATIONS
Capacity From 2” to 78” (over 36” on request]
Clamping system Split frame configuration 4 to 8 independent jaws
Tool feed Automatic with a clutch system
(remote controlled on request)
Cutting speed Adjustable between 5 and 18 meters/mn
Motor drive Right angle pneumatic drive 2.5 HP
From TTNG 406: 2 x 2.5 HP
FEATURES
b A variety of tool sizes for pipe severing and beveling
from 2” to 78” in diameter
b Rugged, low friction bearing system
b Counterbore modules for accurate I.D. machining
b Powerful pneumatic or hydraulic drive motors
b Field adjustable bearings
b Completely enclosed drive gears for operator safety
b Adjustable clamping jaws for maintaining concentric cuts.
OPTIONS
b Electric drive
b Hydraulic drive
b Copying carriage with template
b OD tracker
b Cutting wheel
b Counterboring.
17. 17
DIMENSIONS
model capacity A
mm
B
mm
C
mm
D
mm
E
mm
Weight
kg
TTNG-168 2”• 6” 175 325 217 107 192 34
TTNG-219 4”• 8” 223 373 241 107 192 37
TTNG-273 6”•10” 283 433 271 107 192 44
TTNG-323 8”• 12” 331 481 295 107 192 46
TTNG-406 10”•16” 415 565 337 107 192 51
TTNG-508 12”• 20” 517 667 388 107 192 66
TTNG-610 16”• 24” 619 788 448 107 192 77
TTNG-762 22”• 30” 776 945 526.5 107 192 94
TTNG-900 26”• 36” 925 1094 601 107 192 111
TTNG-1000 32”• 40” 1016 1200 700 107 192 137
TTNG-1200 36”• 48” 1262 1540 826 107 192 170
TTNG-1400 48”• 56” 1460 1730 910 107 192 205
B
E
ØA
D
C
18. 18
b The TTLW series
machines will sever bevel
simultaneously. The light
weight TTLW can be easily
mounted on IN –line piping
system. The TTLW.is designed
to be set up in tight places.
The turning ring is rolling in
adjustable bearings to give
the possibility to be reset.
b The TTLW can perform a
cut up to 30mm wall on any
material and cut bevel on
carbon steel up to 20 mm.
b A variety of weld joint designs can be accomplished including square
sever, double bevel, J bevel counter-bore, compound bevel and socket
weld removal.
TUBE CUTTING AND BEVELING MACHINE
TTLW SERIES
FEATURES
b Split frame configuration
b A variety of tool sizes from 2’’ up to 24’’
b Rugged low friction bearing system adjustable .
b Counter bore module for accurate ID machining.
b Powerfull pneumatic or hydraulic drive with comple enclose drive
gears for operator safety
b Rugged tool holders, with no adjustment to save time.
b To avoid premature wear out, the tool holder lead screw is
completely enclosed
b Radial adjustable clamping jaws
OPTIONS
b Axial radial adjustable clamping jaws
b OD tracking tool holder to follow ovalization
b Copying carriage for bevelling using single point machining.
b Counter boring tool holder
b Cutting wheel
b Electric drive
b Hydraulic drive
b Hinge
b Enveloping jaws
19. 19
TECHNICAL SPECIFICATIONS
Capacity From 2” up to 24”
Tool feed Automatic via a clutch system
Remote control on request
Cutting speed Adjustable
Motor drive Pneumatic / Electric or Hydraulic
DIMENSIONS
model capacity A
mm
B
mm
C
mm
Ø D
mm
E
mm
F
mm
G
mm
J
mm
Weight
kg (1)
TTLW-168 2”• 6” 213 313 210.7
Dependingontoolholderposition
82 148 80 277 14
TTLW-219 4”• 8” 267 361 237.7 82 148 80 304 16.5
TTLW-273 6”•10” 321 421 264.7 82 148 80 331 19
TTLW-323 8”• 12” 375 475 291.7 82 148 80 358 21.5
TTLW-406 10”•16” 459 559 333.7 82 148 80 400 25
TTLW-508 12”• 20” 561 661 384.7 82 148 80 451 35
TTLW-610 16”• 24” 669 769 438.7 82 148 80 505 40
(1) Without motor and tool holders
20. 20
b The TTSNG and TTSRD
machines are designed
as the TTNG series
to cut and/or bevel
tubes and pipes in one
simultaneous operation
up to 15 mm WT on
carbon steel.
b The lightweight and
low-clearance of those
versions allow precise machining within very restricted working areas.
b High speed tool steel cutting bits provide accurate weld joint
machining while eliminating flame cutting and grinding procedures.
b A variety of weld joint designs can be
accomplished including square sever, double
bevel, J bevel counterbore, compound bevel
and socket weld removal.
b The TTSRD version are equipped wih a
special clamping collets system which allow a
quick and auto-centering clamping pipe. That
model can only cut up to 5 mm WT.
TUBE CUTTING AND BEVELING MACHINE
TTSNG and TTSRD SERIES
(Light weight and low-clearance)
FEATURES
b Machining capacity: 1/8” to 10”
b Heavy duty, Tool holder ring gear drive
b Split frame configuration: opening in 2 half-shells.
b Field adjustable bearings
b Pneumatic, electric or hydraulic drive motors
b The feed system may be clutched and unclutched
b Completely enclosed drive gears for operator safety
b Adjustable clamping jaws for maintaining concentric cuts.
TECHNICAL SPECIFICATIONS
Capacity From 1/8” to 10” (more on request)
Clamping system 4 independent jaws for TTSNG; collets for TTSRD
Tool feed Automatic with a clutch system
Cutting speed Adjustable between 5 and 12 meters/mn
Motor drive In line or right angle pneumatic drive 1HP
OPTIONS
b Counterboring
b TTSRD: - Clamping by collets
- Auto-centering system
TTSRD 88
21. 21
DIMENSIONS (1)
model capacity A
mm
B
mm
C
mm
D
mm
E
mm
Weight
kg
TTS NG 27 1/8”• 3/4” 30 106 99.5 59.3 126 3.5
TTS NG 33 1/8”• 1” 36 112 102.5 59.3 126 4
TTS NG 42 1/8”• 1”1/4 45 121 107 59.3 114 4.5
TTS NG 48 1/8”• 1”1/2 51 127 110 59.3 114 5
TTS NG 60 1/2”• 2” 63 139 116 59.3 114 5.3
TTS NG 73 1/2”• 2”1/2 75 151 122 59.3 114 5.5
TTS NG 88 1”• 3” 90 166 129.5 59.3 114 6
TTS NG 101 1”1/2• 3”1/2 105 181 137 59.3 114 6.5
TTS NG 114 2”• 4” 117 193 143 59.3 114 7
TTS NG 127 2”• 4”1/2 129 205 149 59.3 114 7.5
TTS NG 141 2”1/2• 5” 144 220 156.5 59.3 114 8.5
TTS NG 168 3”• 6” 171 247 170 146 114 10
TTS NG 193 4”• 7” 195 271 182 158 114 11
TTS NG 219 5”• 8” 222 298 195.5 171.5 114 12
TTS NG 273 7”• 10” 276 352 222.5 59.3 114 14
(1) TTSRD: Dimensions on request.
C
D
E
B
A
22. 22
b The flange facing
attachment has been
designed to be quickly adapted
on any standard pipe bevelling
machine of our range, to
further multiply its use by also
allowing it to resurface all the
different flanges welded on
pipes, directly on site,
b Therefore we have a
portable inner clamping flange
facing machine to perform
any geometry required by the
customer, by just bringing the
tool to the flange on site, where most needed.
b One skilled operator will adapt it on our machines in a matter of
minutes. Its clutch, dual side machining and differents feeds will allow
the operator to face damaged
flanges to their original shape and
with different finishes.
b It may be used by clamping the
machine directly inside the pipe,
or if an extreme squareness and
centering is required, the spider
shaped elbow mandrel kit will be
necessary.
FLANGE FACING ATTACHMENT
Machine Minimum Maximum Inches
US25ACC 25 mm 300 mm 1’’ • 12’’
US30ASB 50 mm 355 mm 2’’ • 14’’
US40ASB 70 mm 400 mm 2’’1/2 • 16’’
US80ASB 100 mm 610 mm 4’’ • 24’’
US150ASB 165 mm 900 mm 6’’1-2 • 36’’
DIMENSIONS
US150ASB
OPTIONS
b The machines have to be hydraulic
driven with a 4 kW or 5.5 kW Protem
power pack ( version from US40ASB).
US25ACC
US40ASB
23. 23
b The MF series has been
designed to cut and bevel tubes
from 60.3 mm OD up to
406 mm OD.
The MF machine is electric
driven with 3 phase motor with
speed adjustment, has a fast
concentric clamping device,
2 opposite tool holders fixed on
the turning plate, and a safety
cover to protect the operator.
The machines are equipped
with control box with start/stop
emergency stop buttons.
The MF machine can perform
high quality welding preparation on any steel.
TUBE CUTTING AND BEVELING MACHINE
TYPE MF 170 / MF 420
TECHNICAL SPECIFICATIONS
Model MF 170 MF 420
Clamping and machining
range capacity
60.3 mm up to 168 mm 168 mm up to 406 mm
Tool feed 60 mm 50 mm / 80 mm
Tool rotation adjustable 10-80 rpm adjustable 16-52 rpm
Weight 180 kg 500 kg
Motor drive electric / 3 phases electric / 3 phases
Optional equipment cut holder cut holder
DIMENSIONS
model A (mm) B (mm) C (mm) D (mm) E (mm)
MF 170 1250 790 818 545 660
MF 420 1641 970 990 550 1010
A
B
D
C E
lameChurchillTwintips1230
lameChurchillTwintips1230
24. 24
b The portable machine
SE 25 is specially designed
for squaring in position the
diameters from 2 mm to
25.4 mm O.D.
b The tool holder plate
equipped with 1 tool
insert allows to cover the
machining range without
any adjustment.
b The setup of the tube is
carried out quickly through
a stainless steel monobloc collet.
b The machine features a graduated vernier which gives a high quality
and accurate weld prep.
TUBE AND FITTING SQUARING MACHINE
TYPE SE 25
TECHNICAL SPECIFICATIONS
Clamping capacity From 2 mm O.D. to 25.4 mm O.D.
Machining capacity From 2 mm O.D. to 25.4 mm O.D.
RPM Offload: O to 1200 rpm
Weight 2.5 kg
Feed Graduated manual feed 1 div = 0.1 mm
Feed stroke 10 mm
Drive Cordless electric drive
Optional equipment - Right angle drive
- Bench mounting provision
- Machine on mains current
- Dual clamping device
- Beveling tool blocks
DIMENSIONS
25. 25
b The portable machine SE 25
right angle is specially designed
for squaring in position the
diameters from 2 mm to
25.4 mm O.D.
b The tool holder plate equipped
with 1 tool insert allows to
cover the machining range
without any adjustment.
b The setup of the tube is
carried out quickly through a
stainless steel monobloc collet.
b The machine features a
graduated vernier which gives a high quality and accurate weld prep.
TUBE AND FITTING SQUARING MACHINE
TYPE SE 25 RA (low clearance)
DIMENSIONS
TECHNICAL SPECIFICATIONS
Clamping capacity From 2 mm O.D. to 25.4 mm O.D.
Machining capacity From 2 mm O.D. to 25.4 mm O.D.
RPM Offload: O to 1200 rpm
Weight 2.5 kg
Feed Graduated manual feed 1 div = 0.1 mm
Feed stroke 10 mm
Drive Right angle cordless electric drive
Optional equipment - Bench mounting provision
- Dual clamping device
417,5
88
125,562
= =
78
= =
26. 26
b The portable machine
SE 65 is specially designed
for squaring in position the
diameters from 12.7 mm
to 60.3 mm O.D.
b The tool holder plate
equipped with 2 tool
inserts allows to cover the
machining range without
any adjustment.
b The setup of the tube is
carried out quickly through
a stainless steel monobloc
collet.
b The machine features a graduated vernier which gives a high quality
and accurate weld prep.
TUBE AND FITTING SQUARING MACHINE
TYPE SE 65
TECHNICAL SPECIFICATIONS
Clamping capacity From 12.7 mm O.D. to 60.3 mm O.D.
Machining capacity From 12.7 mm O.D. to 60.3 mm O.D.
RPM Off load: 0 to1200 rpm
Weight 3.5 kg
Feed Graduated manual feed 1 div = 0.1 mm
Feed stroke 10 mm
Drive Cordless electric drive
Optional equipment - Right angle drive
- Bench mounting provision
- Machine on mains current
- Dual clamping device
DIMENSIONS
27. 27
b The SL series has been
especially made to square
tubes, fittings and tees.
b The clearances, capacities
and designs have been
engineered along with the end-
user industries. Ideal for clean
room application.
b Perfect for squaring tees and
fittings.
b Machining accuracy for orbital welding.
b Can be used as a portable tool or bench mounted.
b Machining of all steels, stainless steels, inconels and exotic alloys.
MACHINING OF TUBES AND FITTINGS
TYPE SL 30 - 60 - 120
TECHNICAL SPECIFICATIONS
Clamping capacity SL13: 3 to 13 mm O.D.
SL30: 3 to 30 mm O.D.
SL60: 13 to 63.5 mm O.D.
SL 120: 50 to 120 mm O.D.
Weight SL13: 4 kg
SL 30: 5 kg maxi
SL 60: 5.5 kg maxi
SL 120: 6.5 kg maxi
28. 28
b The SE SERIES end prep
tools are lightweight and
portable.
b They will perform repeatable
quality weld preps on most
metal pipes and tubes
including stainless steel from
5 to 120 mm O.D.
b The cutting head will bevel,
face and counter bore
individually or in synchronized
operation. The tool holder can
hold up to 4 tool blocks. The
tool holder is easily removable
and thus allows the operator to save time once the tool blocks have
been adjusted by exchanging the whole tool.
b The SE SERIES machines are available with either pneumatic or
electric drive. The SE machine holds the tube by the mean of heavy
duty collets made in 3 parts at OD tube dimension.
TUBE SQUARING and BEVELING TOOLS
SE 60 / SE 90 / SE 120
Clamping and machining
capacity
SE 60 : 10 mm to 60 mm O.D.
SE 90 : 25 mm to 90 mm O.D.
SE 120 : 60 mm to 120 mm O.D.
Tool bit rotation Off load speed : 0 to 221 rpm
Weight SE 60 : 7.5 Kg
SE 90 : 8.5 kg
SE 120 : 9.5 kg
Feed Manual feed - 25 mm travel
Drive 1HP or 2HP Pneumatic motor
Option 1200 W Electric drive
Additional tool blocks
Bench mounting provision
Automatic clamping
TECHNICAL SPECIFICATIONS
SE 60 presented on a bench with automatic
clamping device
SE Series portable machines designed for
heavy duty jobs
29. 29
b The SE 219 has been
especially designed and
engineered to face and
bevel tubes from 60.3 mm
up to 219 mm O.D.
b Its design and unique
range of diameters ranks
it as the best tool in its
class. The stainless steel
or aluminium collet and
its front support allow
a perfect clamping and
squareness.
b Without deformation for orbital welding.
b 4 tool holders can be mounted on the tool holder plate to work
simultaneously.
b This tool is ideal for sanitary tubing, food processing, chemical and
pharmaceutical applications. The SE 219 can be mounted either with
an electric drive or with a pneumatic drive.
O. D. CLAMPING FACING AND BEVELING
MACHINE SE 219
TECHNICAL SPECIFICATIONS
Standard clamping and
machining capacity
60.3 mm up to 219 mm O.D.
Tool rotation 0 to 30 rpm
Tool feed Manual. Travel: 23 mm
Weight 30 kg
Motor drive Pneumatic drive: 1 HP
Optional equipment - Electric drive: 1200W
- Facing tool block and beveling
- Tool block for thin wall
DIMENSIONS
31. 31
b The hydraulic HSB
machine can be used
either on site or in
the workshop. This
heavy duty beveler
will bevel, face and
counterbore individually
or simultaneously heavy
wall pipes. It will perform
repeatable high quality
weld preps on most metal
pipes including stainless,
duplex, superduplex from 6” O.D. up to 60” O.D. in standard.
b The machine is transportable, easy to install and clamps on the
inside diameter of the pipe. It can be easily operated by one operator.
When used with the optional profile tracking device, it will machine oval
pipes, leaving a root face of a consistent width, which is required when
using orbital welding heads.
b The US HSB series is now recognized worldwide and specifically in
UK, USA, Scandinavia, Belgium, France, Spain, Asia, etc.
HSB SERIES
HIGH SPEED BEVELING MACHINE
TECHNICAL SPECIFICATIONS
Capacity From 6” up to 60”
Machines US 80 HSB . . . . . . . . . 6” - 10”
US 150 HSB . . . . . . . 10” - 14”
US 150 HSB AR(1)
. . . . . 6” - 14”
US 220 HSB . . . . . . . 14” - 22”
US 420 HSB . . . . . . . 22” - 30”
US 420 HSB AR(1)
. . . . 14” - 30”
US 620 HSB . . . . . . . 30” - 38”
US 820 HSB . . . . . . . 38” - 46”
US 1100 HSB . . . . . . 46” - 54”
US 1200 HSB . . . . . . 50” - 60”
Operation and
performance
- Automatic clamping.
- Fully hydraulic driven (feed, clamping, and rotation).
Example 14” x 1” WT y 1 minute
(1) Reduced shaft
32. 32
b The standard PFMs on
the market clamp the pipe
from the inside, but due to
the heavy wall thickness and
reduced inside diameters
often met nowadays, it is
impossible to do so.
b PROTEM has designed a
generation of PFMs which
can grab the tube from the
outside: The OHSB Outside
high speed beveller.
b This design allows bevelling
with internal wheel trackers even with a small inside diameter.
b The OHSB can also bevel extremely heavy walls up to 70 mm in a
few minutes.(option: Special carriage)
b Example: A 10” pipe wt 60 mm bevelled in 4 minutes.
b Bevel shape: 4° + nozzle 2 mm x 2 mm and counter boring of 15°.
b The amazing OHSB concept is all hydraulic controlled and can also
bevel cladded pipe with a very precise result on the nozzle.
b The exclusive auto-centring clamping system (patented) allows a very
accurate and quick pipe positioning.
PIPE FACING MACHINE OHSB
outside clamping
OHSB 4’’ • 14’’
OPTIONS
b Counter boring (up to 160 mm)
b OHSB C: Copying carriage for heavy wall
thickness
b OHSB S: OHSB with a long counter-boring
attachment
Model OHSB 4’’ • 14’’ OHSB 6’’ • 16’’
Clamping capacity 4’’ up to 14’’ 6’’ up to 16’’
Machining capacity 0 up to 323 mm 0 up to 406 mm
Wall thickness
capacity
30 mm (option 75 mm) 30 mm (option 75 mm)
Tool bits Carbide inserts Carbide inserts
Rotation speed 0 up to 237 rpm 0 up to 200 rpm
Stroke 150 mm (option 200 mm) 150 mm (option 200 mm)
Hydraulic power pack 55 kW 55 kW
Weight (a round:) 1 700 kg 2 000 kg
Dimensions H x l x L 1 000 x 1 000 x 2 000 mm
TECHNICAL SPECIFICATIONS
33. 33
b The TNO machines
have been especially
designed to fit your
piping or tubing
prefab application
on site or in your
workshop.
b These machines
will sever and bevel
heavy wall pipes
faster than any
other machine.
They will save you
man hours by avoiding grinding operations, flame cutting, difficult
handling and setting of pipes on a lathe.
b Transportable, rigid, fast and accurate are the main qualities of
these units.
TNO SERIES
TRANSPORTABLE SEVERING AND
BEVELING MACHINE
TECHNICAL SPECIFICATIONS
Capacity From 4” up to 48”(1)
Length
Machines TNO 4” to 12” 114 mm to 323 mm
TNO 14” to 24” 355 mm to 610 mm(2)
TNO 26” to 36” 660 mm to 914 mm(2)
TNO 38” to 48” 965 mm to 1219 mm(2)
1515 mm
1515 mm
1957 mm
Contact us
Operation and
performance
Manual set up of tube, automatic feed, automatic clam-
ping, electric drive with variable speed.
(1) Larger units available on request.
(2) Optional kit (14” - 18”) (24” - 28”) (38” - 42”) if cutting more than 12 mm wall.
34. 34
b The CTA machines have
been especially designed to fit
your piping or tubing prefab
application in your workshop.
b This machine can integrate
your production line with no
specific changes.
b The quality of machining
achieved with the CTA can be
compared to a CNC machine.
b By combining severing to
the right length, and beveling
simultaneously in only seconds
this machine has become
a reference in the industry
and specifically in USA,
Ireland, Malaysia, Argentina,
Venezuela, Belgium, France.
SEVERING AND BEVELING MACHINE
CTA SERIES
TECHNICAL SPECIFICATIONS
Capacity From 2” up to 36”(1)
Machines CTA 2” to 12” 60 mm to 323 mm
CTA 6’’ to 16’’ 168.3 mm to 406 mm
CTA 14” to 24” 355 mm to 610 mm
CTA 26” to 36” 660 mm to 910 mm
Operation and
performance
Manual setting of the tube.
Automatic clamping and automatic feed.
Optional equipment - Pipe conveyor
- Height positioning device
- Pipe measuring system
- Chip removal conveyor
- Lubrication unit
(1) Larger units available on request
CTA 14”-24”. Option: chips conveyor, elevating table.
35. 35
b This tool allows to perform
up to 4 simultaneous
machining operations
(internal/ external bevels,
land, counterboring) on tubes
ranging from 88.9 mm O.D.to
430 mm O.D up to 25.4 mm
wall thickness.
b These BB heavy duty pipe
bevelling machines have been
designed for prefabrication
for today’s heavy wall pipe
thickness
b It is powered by a 15 kw electric drive with electronical speed
adjustment, manuel feed (optional electrical drive) and manual
clamping (optional electric drive)
b High speed machining with carbide inserts
b Exemple: 323 x 25 mm wall = 2 minutes only.
BEVELING WORKBENCH BB 3’’ - 16’’
OPTIONS
b Semi-automatic clamping
b Semi-automatic feed
b Lubrication
b Chip conveyor
b Independant control panel
TECHNICAL SPECIFICATIONS
Clamping capacity 75 mm to 430 mm O.D.
Machining capacity 88.9 to 406 mm (3’’ to 16’’)
Maximum wall thickness 25.4 mm
Tool bits Carbide inserts
Rotation speed 5 rpm to 200 rpm
Feed stroke 150 mm
Electric power 15 kw
Volts 400 volts
Weight 1 800 kg
Dimensions H x l x L 1 850 x 1 200 x 1 950 mm
Independent control panel
36. 36
b This tool allows to perform
up to 4 simultaneous
machining operations
(internal/ external bevels,
land, counterboring) on tubes
ranging from 323 mm O.D.to
610 mm O.D up to 45 mm
chips wall thickness.
b These BB heavy duty pipe
bevelling machines have been
designed for prefabrication
for today’s heavy wall pipe
thickness
b It is powered by a 15 kw electric drive
with electronical speed adjustment,
manuel feed (optional electrical drive)
and manual clamping (optional electric
drive)
b High speed machining with carbide
inserts
b Exemple: 323 x 25 mm wall =
1 minute only.
BEVELING WORKBENCH BB 12’’ - 24’’
OPTIONS
b Semi-automatic clamping
b Semi-automatic feed
b Lubrication
b Chip conveyor
b Independant control panel
b ID trackers conveyor
TECHNICAL SPECIFICATIONS
Clamping capacity 320 mm to 630 mm Ext.
Machining capacity 323 to 610 mm (12’’ to 24’’)
Maximum wall thickness 45 mm total length for the chips
Tool bits Carbide inserts (possibility of 4 tool holders)
Rotation speed 16 rpm to 80 rpm
Feed stroke 150 mm
Electric power 37 kW
Volts 380/ 400 volts – 50 Hz (other consult us)
Weight 8 000 kg
Dimensions H x l x L 2 014 x 2 930 x 2 000 mm
37. 37
b The US 600 R is a
transportable machine
which can perform bevels
from 600 mm up to
1000 mm (version 1)
1000 mm up to 1500 mm
(version 2).
b The US 600 R is able to
perform weld preparation
(J prep, Vprep, compound
bevel…) with repeatable
high quality, on carbon
steel, stainless steel,
alloy, inconel, duplex,
superduplex…
b The US 600 R is using
standard carbide inserts,
and can bevel easily up to
4 wall pipe.
The machine is hydraulic
driven connected to a
22 kW power pack.
US 600 R
PIPE BEVELING MACHINE
TECHNICAL SPECIFICATIONS
Clamping capacity - Version 1 from 545 mm up to 1000 mm
- Version 2 from 1000 mm up to 1500 mm
Machining capacity - Version 1 from 600 mm up to 1000 mm
- Version 2 from 1000 mm up to 1500 mm
Tool feed Adjustable
Tool rotation 0 – 50 rpm
Weight - Version 1: 1500 kg
- Version 2: 2000 kg
Motor Dual hydraulic drive
Detail of the copying carriage
41. 41
PROTEM SAS
Z. I. Etoile
F-26800 Etoile-sur-Rhône
tél. +33 (0) 4 75 57 41 41
fax +33 (0) 4 75 57 41 49
www.protem.fr
42. 42
INFO REQUEST
In order to offer you the best suitable equipment for your application
we recommend that you fill in this technical application form.
Brief description of work to be performed:
(pipe, flange, other…)............................................................................
.................................................................................................
.................................................................................................
.................................................................................................
.................................................................................................
Material:......... Ø (O.D. or I.D.) of pipe/flange: from............ to...........
Wall thickness: ............................................................................
Technical specifications:.................................................................
(type of bevel or machining, angle, surface roughness.tolerances etc.)
Quantities:........................... Cycle time allowed:..............................
(lf production specify per min/hour/day)
Clearance/weight/handling requirement: ........................................
Working area:..............................................................................
(On site, workshop, contaminated etc.)
Power drive requested: v Pneumatic v Electric v Hydraulic
Drawing provided: v yes v no
Request:.....................................................................................
(Specific brochure, quote, demonstration, call etc.)
Contact name: ................................ Position:................................
Company:........................................Address:................................
.................................................................................................
.................................................................................................
Tel:....................................................... Fax:................................
SKETCH:.....................................................................................
.................................................................................................
.................................................................................................
.................................................................................................
