muhammad jawhar

1. Kurdistan Region
Salahaddin University-Erbil
College of Engineering
Mechanical and Mechatronics Engineering Department
Title
A Project Submitted to the Mechanical Engineering Department
University of Salahaddin-Erbil
in the Partial Fulfillment of the Requirement for the Degree of Bachelor of Science
in Mechanical Engineering
Prepare By:
Student StudentStudent
Student StudentStudent
Student StudentStudent
Student StudentStudent
Supervisor:
Dr. ----------------------
2017 - 2018

2. ii
Abstract
This template is in the correct format, just type over it and save it as your
document. (No more than 1 page).

3. iii
Acknowledgement
You may wish to include an acknowledgement. This should be a maximum
of one page and is usually much less. In this you should thank whoever may
have helped you in any way. This will usually be your project supervisor,
but could include other staff suchas technicians, and anyone else you would
like to thank.

4. iv
Supervisor’s Certificate
I certify that the engineering project titled "Title” was done under my
supervision at the Mechanical Engineering Department, College of
Engineering - Salahaddin University–Erbil. In the partial fulfillment of the
requirement for the degree of Bachelor of Science in Mechanical
Engineering
Supervisor
Signature:
Name: Assist. Prof. Dr.
Date: / /

5. v
List of Contents
Abstract...................................................................................................ii
Acknowledgement ..................................................................................iii
Supervisor’s Certificate...........................................................................iv
List of Contents ...................................................................................... v
List of Figures .......................................................................................vii
List of Tables .......................................................................................viii
Nomenclature.........................................................................................ix
1 Introduction ..................................................................................... 1
1.1 A Major Section.......................................................................... 1
1.1.1 A Major Subsection........................................................... 2
1.1.1.1 A Minor Section................................................... 2
2 Methodology..................................................................................... 3
2.1 A Major Section.......................................................................... 3
2.1.1 A Major Subsection........................................................... 3
2.1.1.1 A Minor Section................................................... 3
3 Example of Analysis and Design ...................................................... 4
3.1 A Major Section.......................................................................... 4
3.1.1 A Major Subsection........................................................... 4
3.1.1.1 A Minor Section................................................... 4
4 Results and Discussion..................................................................... 5
4.1 A Major Section.......................................................................... 5
4.1.1 A Major Subsection........................................................... 5
4.1.1.1 A Minor Section................................................... 5
5 Conclusion and Recommendations .................................................. 6
5.1 A Major Section.......................................................................... 6
5.1.1 A Major Subsection........................................................... 6
5.1.1.1 A Minor Section................................................... 7

6. vi
References.............................................................................................. 8

7. vii
List of Figures
Figure 1.1 College of Engineering Logo. ................................................. 1
Figure 4.1 Salahaddin University-Erbil Logo........................................... 5

8. viii
List of Tables
Table 1.1 December 2016. ...................................................................... 2
Table 5.1 ABC........................................................................................ 6

9. ix
Nomenclature
You may wish to include a nomenclature if you have many mathematical
symbols. Remember that your reader may not be an expert in the field of
your project. In any case, symbols should be defined on first appearing in
text.

10. 1
Chapter One
1 Introduction
1.1 A Major Section
An introduction should be written to the project and should, at least, involve
the following points:
1. A background, history or general information about the project.
2. The problem statement of the project showing the issue that is going
to be solved in the project (if applicable).
3. Aims and objectives of the project.
4. An outline of the chapters included in the project.
Figure 1.1 College of Engineering Logo.

11. 2
1.1.1 A Major Subsection
Your words go here …
1.1.1.1 A Minor Section
Your words go here …
Table 1.1 December 2016.
Sunday Monday Tuesday Wednesday Thursday Friday Saturday
1 2 3
4 5 6 7 8 9 10
11 12 13 14 15 16 17
18 19 20 21 22 23 24
25 26 27 28 29 30 31

12. 3
Chapter Two
2 Methodology
2.1 A Major Section
This chapter contains the methods that are used in the analysis and/or design
of the case with detailed procedures. It should not include any sample of
calculation. If the project involves derivations of equations, they should also
be written in this chapter.
2.1.1 A Major Subsection
Your words go here …
2.1.1.1 A Minor Section
Your words go here …

13. 4
Chapter Three
3 Example of Analysis and Design
3.1 A Major Section
In this chapter, the student is required to apply the procedures of
Methodology chapter on a relevant example to his/her project, and present a
good example of analysis and/or design (or estimation, …etc) with a detailed
calculation.
3.1.1 A Major Subsection
Your words go here …
3.1.1.1 A Minor Section
Your words go here …

14. 5
Chapter Four
4 Results and Discussion
4.1 A Major Section
The results obtained from the project should be organized in tables orshown
by figures and curves, briefly. After that, the results should be clearly and
critically discussed. Inthis chapter, the studentshould beable to show his/her
understanding of the subject and its results.
4.1.1 A Major Subsection
Your words go here …
4.1.1.1 A Minor Section
Your words go here …
Figure 4.1 Salahaddin University-Erbil Logo.

15. 6
Chapter Five
5 Conclusion and Recommendations
5.1 A Major Section
The conclusions of the project should be briefly presented in this chapter. It
should conclude the main findings and link them to the objectives of the
study.
Note that the conclusion is not an abstract, it should NOT summarize the
whole project.
Table 5.1 ABC.
A B C
5.1.1 A Major Subsection
Your words go here[1] …

16. 7
5.1.1.1 A Minor Section
Your words go here [2]…

17. 8
References
[1] V. Jagannath and U. C. Shekar,, "Precast L-Pan Roof Elements for
Low CostHosing," Journalof Ferrocement, vol. 19, no. 4, pp. 353 -
361, October 1989.
[2] J. G. MacGREGOR and J. K. Weight,, Reinforced Concrete
Mechanics, 4. Edition, Ed., Pearson Prentice-Hall Book Company,
2005.