3. 3
Abstract
Thermo acoustic refrigeration is a phenomenon
that uses high intensity sound waves in a
pressurized gas tube to pump heat from one
place to other to produce refrigeration effect.
This system completely eliminates the need for
lubricants and results in 40% less energy
consumption.
May 23, 2017
4. 4
Introduction
Thermo acoustic devices take advantage of
sound waves reverberating within them to
convert a temperature differential into
mechanical energy or mechanical energy into a
temperature differential.
Thermo acoustic devices perform best with
inert gases.
They do not produce the harmful
environmental effects such as global warming
or stratospheric ozone depletion.
May 23, 20174
7. 7
Basic Functioning
A thermo acoustic refrigerator uses acoustic
power to pump heat from a cool source to a hot
sink.
These devices perform best when they employ
noble gases as their thermodynamic working
fluids.
The principle can be imagined as a loud speaker
creating high amplitude sound waves that can
compress refrigerant allowing heat absorption.
sound waves travel by compressing and
expanding the gas they are generated in
May 23, 20175
8. 8
Basic Functioning
Suppose the wave is traveling through a tube, a
temperature gradient can be generated by putting
a stack of plates in the right place in the tube, in
which sound waves are bouncing around.
Some plates in the stack will get hotter while the
others get colder
May 23, 2017
9. 9
Thermo Acoustic Effect
Acoustic or sound waves can be utilized to
produce cooling.
The pressure variations in the acoustic wave are
accompanied by temperature variations due to
compressions and expansions of the gas.
As expansion and compression in an acoustic
wave are inherently associated with a
displacement, a net transport of heat results.
To fix the direction of heat flow, a standing wave
pattern is generated in an acoustic resonator.
May 23, 2017
10. 10
Theoretical Basics
Thermoacoustic refrigerator is a special kind of device
that uses energy of sound waves or acoustic energy to
pump heat from low temperature reservoir to a high
temperature reservoir.
May 23, 2017
11. 11
Main Prototype Components
Two main parts are in the TAR
A. Driver
• Houses the Loudspeaker
A. Resonator
• Houses the gas
• The hot and cold heat exchangers
• Houses the Stack
May 23, 2017
12. 12
Loudspeakers
A loudspeaker (or "speaker") is an
electroacoustic transducer that produces sound
in response to an electrical audio signal input.
It was invented in the mid 1820’s by the scientist
Johann Philipp Reis.
It is powered by electricity.
The magnet or the coil in the speaker vibrates to
produce the waves of required frequency.
May 23, 2017
16. 16
Stack
It is also called as regenerator.
The most important piece of a thermoacoustic device is
the stack.
The stack consists of a large number of closely spaced
surfaces that are aligned parallel to the to the resonator
tube.
In a usual resonator tube, heat transfer occurs between
the walls of cylinder and the gas.
The different materials used in the Stack are
Paper
Alluminium
Lexan
Foam
May 23, 2017
17. 17
Stack
Considerations
Gap size
Material properties
Material thickness
Location
Length
Does not impede wave
Choice
Paper
Aluminum screen
May 23, 2017
18. 18
Heat Exchangers
Heat exchangers are devices used to transfer heat
energy from one fluid to another.
A heat exchanger is a piece of equipment built for efficient
heat transfer from one medium to another.
The media may be separated by a solid wall, so that they
never mix, or they may be in direct contact.
May 23, 2017
20. 20
Thermo-acoustic Cycle
The figure traces the basic
thermo-acoustic cycle for a packet
of gas, a collection of gas
molecules that act and move
together.
Starting from point 1, the packet
of gas is compressed and moves
to the left.
As the packet is compressed, the
sound wave does work on the
packet of gas, providing the
power for the refrigerator.
May 23, 2017
21. 21
Thermo-acoustic Cycle
As the packet is
compressed, the sound
wave does work on the
packet of gas, providing the
power for the refrigerator.
When the gas packet is at
maximum compression, the
gas ejects the heat back
into the stack since the
temperature of the gas is
now higher than the
temperature of the stack.
May 23, 2017
22. 22
Thermo-acoustic Cycle
This process results in a net
transfer of heat to the left
side of the stack.
Finally, in step 4, the
packets of gas reabsorb
heat from the cold reservoir.
And the heat transfer
repeats and hence the
thermoacoustic refrigeration
cycle.
May 23, 2017
23. Advantages 23
May 23, 201718
The working fluid is typically helium or other inert,
benign gases such as air which are environment-friendly
unlike common refrigerants.
The simplicity of the design makes it robust, small, and
lightweight.
It has almost no moving parts, which translates into a
longer working life with fewer repairs. In turn, this makes
the system less expensive.
The loudspeaker is TAR’s only moving part which is
more durable than a compressor.
It has the ability to attain a higher level of the limiting
Carnot efficiency than current refrigeration methods.
24. Disadvantages 24
May 23, 201719
The downside of the TAR is that these failed to achieve
efficiencies as high as those of standard refrigerator
units.
The coefficient of performance of most advanced TAR is
only 1 when compared to 3-4 of modern refrigerators.
Another major problem of TAR is that it is either fully on
or off.
It leaked an incredible amount of sound that causes ear
pain but produces only a small temperature gradient.
These refrigerators were able to cool the air for a short
amount of time before the cooled air started raising its
temperature.
25. Improvements 25
May 23, 201719
Insulate the sound leaks by isolating the system.
Replace the closed cap with a speaker to increase the
efficiency by co-generation.
If both ends of a stack are connected to a heat
exchangers thus coupling the stack to a heat source and
sink, the transfer of heat would be more efficient.
Use conductive material for hot section of resonator.
Widen the resonator and use a cone to reduce the
losses due to rapid area change.
More practical and efficient reliable temperature sensors
such as thermostats should be used.
The composition of stack material may also be changed
to any conducting materials like gold, silver or copper.
26. Conclusion 26
May 23, 201719
A Thermo Acoustic Engine Studies In The
Combined Thermo Acoustic Engine Refrigerator
Systems Area Are Only A Handful
This Work Is Only One In Open Literature To
Use Standing Wave Thermo Acoustic
Refrigerator Systems To Cool High
Temperatures
Analysis Of Tar Can Be Obtained By Software
Delta Which Is Used To Investigate Parameters
Like Pressure, Type Of Gas Frequency