1. Transportation & Off Highway
 Chassis Layout
Product
 Fitment for Axle
Development  Structural Design  Selecting & Sizing Support of Major Aggregates
System
 HVAC Design Support
 Product Styling Support
 Interiors & Exteriors Design Support, Packaging,
Harnessing
 Operators Cab Design  HVAC & Ducting
 Engineering Analysis (Including ROPS/FOPS etc.)
 Ergonomics Studies
 Preliminary and requirement study
 Preparing basic layout
 Power Drain Design  Strength calculations to verify layout
Support  Evaluation of Loads and Selection of Bearings
 Design of Transmission Housings
 Selection and verification of bearing
 Tolerance stack-up on critical assemblies
 Engine Peripherals & Components Selection & Re-
Design Support
 Engine Installation  Engine Installation, Packing & System Design Support
(Structural, Functional & Emission Reduction System)
 Emission Reduction Technology
 Validation & Simulation
Vehicle  Schematic generation
Hydraulics  Harness Generation
 Activities  Component Modeling
 Basic Vehicle Hydraulic System
 Schematic Generation
 Competencies  Hose and Tubes Routing
 CFD, Testing, Component Selection & Sourcing
Confidential | Copyright © L&T IES

2.  Schematic generation
Vehicle  Harness Generation
Electricals  Activities  Component Modeling
 Basic Vehicle Hydraulic System
 Schematic Generation
 Competencies  Hose and Tubes Routing
 CFD, Testing
Engineering
Analysis (FEA/  Steady State thermal Analysis
 Thermal Analysis
CAD Services)  Transient thermal Analysis
 Thermal-Structural coupled field Analysis
 Static Analysis
 Dynamic Analysis
 Structural Analysis  Modal Analysis
 Frequency Response Analysis
 Buckling Analysis
 Design Optimization
 Fatigue Analysis
 Advanced Analysis  Multiple Body Dynamics
 Impact Analysis
 Quasi Static Simulation
 Steady & transient flows
 Compressible & incompressible flows
 Conjugate heat transfer analysis
 Computational Fluid  High speed external flows
Dynamics  Porous media analysis
 Multiple reference frame(MRF)
 Multiphase flows
 Stress Life Approach
 Fatigue Analysis  Strain Life Approach
Confidential | Copyright © L&T IES

3. Vehicle  Driver development
Electronics  BSP & Bootloader support
Services
 Communication drivers
 Embedded S/W & Sub-  AUTOSAR compliant development
System Design  Application Software development
 Integrating Third-party Software for Automotive
applications
 Circuit simulation
 Hardware Modeling &  Analysis
Simulation  Rapid Control prototyping
 Algorithm generation
 Auto code generation
 End to End Solution for Product Redesign
 Product Sustenance  Software Sustenance
Support, Customization,  Product Size reduction
Value Engineering  Product Cost Reduction
 Verification & Validation due to Redesign
 Field Failure Analysis & Change Management
 Obsolescence Management
 Product Redesign
 Re- engineering  Product Material Change
 Automated test system Development
 Independent Testing & Validation
 Tester & Tools Service  End-of-line (EOL) Testers
 Hardware-in-the-Loop (HIL) Simulators
 Manufacturing Test Automation Tools
 PC-based Testers
 Firmware Verification and Validation
 Testing, Verification &  Application Software Verification and Validation
 Hardware / Platform Verification and Validation
Validation  Reliability Testing
 Specialization Services  Regulatory Compliance & Certification
 Development of PC based software application
 Application Software Product Engineering Applications
Application Services
Software
 GUI Test Automation of Engineering applications
Services &  Test case design from functional requirements
Testing & Test  Software Testing & Test  System Testing / Load testing / Performance Testing
Automation Automation  Independent Validation, Bug reporting & Result
Services Analysis
 Regression Testing
Confidential | Copyright © L&T IES

4. Manufacturing
Engineering
Services
 Pre Engineering
 Process Engineering
 Process Sheet
 Work Instruction
 3D Scanning of Plant/ Facility for Documentation,
Modification
 Factory Equipment Laser  Video creation for Plant/ Facility for walk through in
Scanning soft form using 3D Scanning
 Generation of Plant 3D Model by Laser Scanning with
all intelligent parameters
 Factory & Utility  Facility Layout
Engineering  Design/Optimization
 Product Redesign
 Virtual Factory Simulation  Product Material Change
 3D Concept of Welding & Assembly Fixtures.
 Fixtures & Gauges  Manufacturing Drawing & BOM Creation.
 Pneumatic distribution & Valve Placement.
 Fixture functions & control diagrams.
 Value engineering.
 Concept, 3D design and manufacturing drawing for
 Containerization & container racks.
Material Handling  Optimization of existing containers racks.
 Trolley concept Design for material flow & Assembly
line.
 Lean Process Design / Optimization, Line Balancing,
Kaizen, Kanban.
 Time & Motion Study (MOST, MODAPTS), Value Stream
Mapping.
 Error Proofing in process design using PokaYoke
 Lean Manufacturing techniques.
 Control system design & Configuration.
 Detail engineering, bought out Specification &
Selection.
 Control Automation  PLC, HMI, Drives, SCADA & Robot programming.
 System Documentation (Operation & Maintenance
Manuals).
Confidential | Copyright © L&T IES

5.  Fatigue Test
 Field Failure Analysis
 Vibration Test
Vehicle Testing  Structural Test  Operator Protective Guard Test
Services  FOPS/ROPS Test
 Strain Gauging Test
 Specification Verification Test
 Vehicle/Attachment Capacity Test
 Road Worthiness Test
 Mass / C.G Tests of machine and attachment
 Radiator & Hydraulic oil Cooler Performance Test
 Cylinder Dropage Test
 Other Tests
 Fuel Consumption Test, Maintainability Index
 Noise Level Measurement
 HVAC Performance Tests
 Hydraulic Brake Performance Test
 Emission Test, Serviceability Tests
 Operator Comfort Verification & Visibility Test
Confidential | Copyright © L&T IES