This technical data sheet provides information on Emulsion Bitumen Medium Setting 60% - SM-K, MS-1K. It is an asphalt emulsion where asphalt is milled into microscopic particles and dispersed in water with an emulsifier. The emulsion has a residue of 60% and is used primarily for surface dressing, tack coats, slurry sealing, and cold mixing in road construction and maintenance applications. Proper handling and safety precautions are required when using this product due to its flammable nature.

1. 10, Bukit Batok Crescent | #04-04 The Spire | Singapore 658079. T +65 63372735 | F +65 63372734. E sales@benzeneinternational.com | E benzene@starhub.net.sg | W www.benzeneinternational.com
Every care has been taken in the preparation of this information. To the extent permitted by applicable law, all warranties and/or representations, express or implied, as to the accuracy of the
information are disclaimed, and no liability is accepted for the accuracy or completeness of the same.© 2003 Benzene International Pte Ltd .The Benzene International logotype (and any other
trademarks) are trademarks of Benzene International Pte Ltd or one of its subsidiaries.
TECHNICAL DATA SHEET
Emulsion Bitumen Medium Setting 60 % - SM-K, MS-1K
Description
When asphalt is milled into microscopic particles and dispersed in water with a chemical emulsifier, it
becomes an asphalt emulsion. The tiny droplets of asphalt remain uniformly suspended until the
emulsion is used for its intended purpose. In the emulsion state, the emulsifier molecules orient
themselves in and around droplets of asphalt. The chemistry of the emulsifier/asphalt/water system
determines the dispersion and the stability of the suspension. When emulsions are used in the field, the
water evaporates into the atmosphere, and the chemical emulsifier is retained with the asphalt
Technical Data
PROPERTIES MEDIUM SETTING 60%
MIN/MAX
TECHNICALLY IDENTICAL
WITH
Residue by evaporation 60% ASTM D244
Sieve 0.1% ASTM D244
Storage stability@1 Day 1% ASTM D244
Particle Charge -/+ Positive ASTM D244
Viscosity @25°C - ASTM D244
Viscosity @50°C 50-450 ASTM D244
ASTM D244 Test on Residue
from Distillation Test
Oil Distillate 20 Max ASTM D244
Penetration @25°C, 100g ,5 Sec 60-200 ASTM D5
Solubility in Tri-choloro Ethylene 97.5Min ASTM D2042
Applications
 The four main application areas are surface dressing, tack coats, slurry sealing, and cold mixing.
 Surface Dressing Road maintenance technique, that involves the restoration of a
deteriorating road wearing course, before the main fabric of the road foundations are
irreparably destroyed
 Tack Coats Provide a thin adhesive film of bitumen between an existing road pavement and
overlay, or between courses in road construction.
 Overlay materials include hot rolled asphalt wearing courses and slurry seal. Tack coats are
also used in patching and inlay work, where further functions of priming and waterproofing
are necessary.
 Tack coat forms an adhesive and cohesive bond between the bituminous overlay and the
existing pavement, reducing the risks of slippage between the two courses, and allowing
traffic stresses to be distributed uniformly.

2. 10, Bukit Batok Crescent | #04-04 The Spire | Singapore 658079. T +65 63372735 | F +65 63372734. E sales@benzeneinternational.com | E benzene@starhub.net.sg | W www.benzeneinternational.com
Every care has been taken in the preparation of this information. To the extent permitted by applicable law, all warranties and/or representations, express or implied, as to the accuracy of the
information are disclaimed, and no liability is accepted for the accuracy or completeness of the same.© 2003 Benzene International Pte Ltd .The Benzene International logotype (and any other
trademarks) are trademarks of Benzene International Pte Ltd or one of its subsidiaries.
Packing
Steel drums
Health & Safety
 Contains petroleum distillate; flammable: keep away from open fire, sparks or other ignition
sources; wear protective clothing, gloves and goggles.
 Fire flammable when wet, flash point 40°C
 Skin –avoid repeated or prolonged contact, if occurs remove with hand cleaner that
removes oil or grease, then clean with soap and water
 Eyes contact could cause irritation, if contact occurs flush immediately with clean water
 Inhalation can cause dizziness, move immediately in fresh air if dizzy and if breathing
difficulty persists administer oxygen.
Cleaning
Tools : Clean with Kerosene
Hands : Use a hand cleanser or kerosene followed by soap and water