1. 1
Muhammad Khan
1582 Clark Blvd  Milton, Ontario L9T 5T6 (905) 878-0369, (647) 282-0875
khan.m786@hotmail.com
Objective:
To obtain a full time position in the aircraft manufacturing/serviceindustry
whereI can utilize my currenttechnical skills.
AircraftEmployment Experience:
May 2014 – August 2014 Noranco Aerospace
Vaughan, ON
 Installation of bearing and bushing to different parts of the aircraft.
 Use of different kinds of PRC’s like 1776. , Kept tidy up the area.
August 2013 –November 2013
Aircraft Sheet Metal Mechanic Premier Aviation (Trois-Rivieres, Quebec)
 Inspect and troubles aircraft structures such as fuselage, tail, wings, and stabilizers.
 Repaired cracks in aircraft skin.
 Operated power Set up and shears, metal brakes, rolls, drills, saws, heat-treating
furnaces, hardness testers and other metal working equipment.
April 2006 – July 2013
Aircraft Structure Technician Mitsubishi Heavy Industries (MHI) Canada.
Aerospace; Mississauga, Ontario
 Worked in the pre-fit department for the Global Express Aircraft
 Worked and maneuvered around the wing and fuselage in order to join the wings
and to take allowable gaps.
 Carefully laid out the skin of the aircraft to drill holes in the rear, front, top and
bottom of the aircraft.
 Installed the rear spar plate as well as the front and rear brackets and upper and
lower bolts.
 Measured and cut the shim according to size for the both wings, experience with
bonding.

2. 2
 Made sure that every part is debarred with Alodine and pasted with the wing
correctly by inspecting the aircraft.
 Dispatched parts, fuselage and wings to Bombardier Aerospace for final assembly.
 Assisted with cat shoot for both wings of the aircraft.
February 2001 – June 2006
Aircraft Manufacturing Technician – Hughes Aero Structures Inc. (Montreal, Quebec.)
 Worked on the Challenger 605 Aircraft at the Bombardier Aerospace Workstation.
 Installed shroud angles to the leading edges as well as heat sensing, anti-ice duck,
grommet sealing.
 Installed completed leading edge assemblies onto the aircraft wings and performed
electrical bonding tests as per industry standards.
 Installed booster pumps, ejector pumps, scavage pumps, pressure relieve valves,
flapper valves, check valves, refuel/defuel tubes, fuel balance tubs, dam plates and
screen assembly.
 Installed and repaired fillet seal, dome seal and aerodynamic seal onto the outer
surface the fuel tank.
 Cleaned fuel tanks for the aircraft and completed final inspections before closing the
access panels to the fuel tank.
July 1995 – April 2000
Aircraft Equipment Maintenance Mechanic Steelbase Services Limited
Mississauga, Ontario.
 Assessed and repaired the aircraft gallery equipment consisting of trolleys, food
warmers, luggage containers as well as other articles.
 Removed all bad rivets or screws, repaired the holes and the frame and re-installed
and sealed new rivets and screws.
 Repaired and installed aircraft seats for Bombardier Regional Jets and De- Havilland
Dash - 8
January 1990 – April 1995
Bench & Structural Assembler McDonnell Douglas Canada Limited
Mississauga, Ontario.
 Prepared sub-assemblies to install on aircrafts MD-80, MD-90 and MD-11 wings.

3. 3
 Drilled, reamed, countersunk, debarred holes and applied Alodine and other
relevant sealants before installation of the universal flush head rivets, huck bolts, hi
locks.
 Measured gaps under the head to make sure the assembly was according to the
industry standard.
 Assembled and installed rib to MD-80 and MD-90 aircrafts.
 Installed stiffner plates to leading edge wing and well as brackets and butterflies to
the MD-80 and MD-90 wing tank panel stringers.
 Installed brackets to the MD-11 fuel tank panel and shaved high rivet heads.
 Applied Alodine and primer to minor scratches.
November 1987 – February 1989
Turbine Engine Assembler – Hawker Siddeley Canada Limited, Orenda Division, Toronto,
Ontario
 Assemble and tested F-404 aircraft engines.
June 1986 – November 1989
Plastic Extruder Operator – Solar Plastics Limited, Toronto, Ontario
 Operated an extruder in order to formulate a vertical blind.
October 1983 – April 1986
Mechanical Fitter – Karachi Electrical Supply Corporation (Karachi, Pakistan)
 Mechanical maintenance of steam turbine boilers and its auxiliary.
April 1977 – October 1983
Turbine Engine Fitter – Pakistan Air force (Karachi, Pakistan)
 Assembled and tested the RD-9B aircraft engine.
Technical AircraftRelated Courses
 Aircraft Sheet Metal and Fabrication – Centennial College (Toronto, Ontario)
 Completed a Bench and Structural Airframe Assembly course from McDonald Douglas
Canada Limited
 7 month course from North York Board of Education, Toronto, ON.

4. 4
 Completed a Mechanical Drafting Course
 Completed a six-month on site training as a Mechanical Fitter.
 Completed a six-month on site training as an aircraft engine overhaul.
 Completed Workplace Hazardous Materials Information System course.
Education
 Grade 12 (Eqvt.)
 Computer Programming & Internet development Analyst - CDI College of Technology
(Mississauga, Ontario)
 Bachelor of Science - University of Karachi, (Karachi, Pakistan).
Member of:
The American Society For Quality (ASQ), Milwaukee, USA.