The document discusses Monarch India, a company that provides flooring solutions. It offers various floor screeds, toppings, primers, and other ancillary flooring products. The products are suitable for a variety of industries and can provide properties like chemical and mechanical resistance, slip resistance, fire resistance, hygienic surfaces, and more. Application procedures and typical product properties are also outlined. The document provides an overview of Monarch's flooring product range and their end-use industries.
2. The flooring is most operational part of any Industrial, Commercial, Residential or
Institutional buildings. The floor is heavily exposed to physical and chemical abuses, load
due to traffic of forklift & trollies, abrasion due to mechanical wear, stress, chemical
resistance to spillages from occasional to continuous immersion, temperature, snow, ice
melting chemicals such as rock salt, slip resistance, impact resistance, fire resistance,
conductivity,aesthetics,rapidcuring,anti-bacterialandpermeabilitytoliquids.Inthishigh
demanding industrial environment, concrete surface fails. Also concrete substrate is
porous in nature thus when water and other fluids enter into concrete, the reinforcing steel
corrodes.Tosustainandmaintaintheindustrialflooraprotectionismust.
Monarch's FloorClad Screeds &Toppings offers seamless high performance flooring
systems to enhance floor design life and for the ultimate convenience of easy to clean
surfacewithincreasedresistancetoliquidpenetration.Thetoughnessanddurabilityofthe
hygienic coating along with choice of attractive colors suits to variety of environmental
conditions. The coated decorative surface presents ideal and pleasant working
atmosphereresultinginproductivityimprovement.
FLOOR SCREEDS TOPPINGS&
Salient FeaturesIndustries ServedApplication
Procedure
www.floorcoatings.co.in | www.floorpaints.biz
» 2 Packs, Pre-measured ratio for ease of on-site
mixing and use
Excellent adhesion to substrate»
Good chemical and mechanical resistance»
Easy application»
Better Pot life»
Economical»
Impervious»
High Glossy aesthetic finish- brightens up dull»
factories and warehouses
Slip resistant surface possible (broadcast & textured)»
Water Breathable coatings»
Seamless / Joint free application possible»
Easily cleaned and maintained»
Hygienic and does not support growth of»
bacteria and fungus
Available in a wide range of colors, to any standard»
RAL card, to improve the working environment
Hard Wearing – durable with low maintenance costs»
Resistance to wide range of chemicals and liquids»
Excellent mold Resistance»
De-contaminable - Bacteria able to be removed»
» Automobile
Beverages»
Biotech plants»
Marine»
Chemical Industries»
Food processing units»
Metal Processing and Engineering Plants»
Oil Refineries»
Paper & Pulp Industries»
Soft Drinks & Bottling Plants»
Steel Plants»
Sugar Factories»
Textile production – bleaching and»
dying – areas.
Water and Sewage treatment plants»
Pharmaceutical plants»
3. Epoxy/Polyurethane Primers for Metal & Concrete Surfaces
Moisture / Water / Oil Insensitive Primers
Water based Primers for Cementitious Floor Screeds
Epoxy based mortars for floor patch repairs/self leveling floor screeds
Cementitious based mortars for floor patch repairs/self leveling floor screeds
Epoxy / Polyurethane Floor Toppings - Re - Lay / Over - Lay Roller Coat
HIGH PERFOMANCE SELF LEVELING FLOOR TOPPINGS
ANCILLARY FLOORING PRODUCTS
MonoBond FP
MonoBond SFP
MonoBond EP
MonoBond SEP
MonoBond PP
Name Code Pack Size Description
MonoBond MICP
MonoBond MIP
MonoBond EC
MonoBond OIP
MonoBond AR
MonoBond SAP
FloorClad EPC
FloorClad SEMS
FloorClad NSC
FloorClad EMS 3000
FloorClad EMS 5000
FloorClad IRS 5000
FloorClad SC
FloorClad FPC
FloorClad SP
FloorClad SCS6
FloorClad SCS12
FloorClad SCS50
FloorClad WEC3000
FloorClad DC
FloorClad EFC
FloorClad MEC
FloorClad PFC
FloorClad EPU
FloorClad FS
FloorClad SL 500
FloorClad SL 1000
FloorClad SL 2000
FloorClad SL 3000
FloorClad SL 4000
FloorClad SL 5000
FloorClad SL5000WB
Floor Clad SL 2000PU
FloorClad EC
MonoMark DC
MonoMark PU2K
FloorClad ANS
11911
11912
11913
11914
11915
11921
11922
11923
11924
11901
11902
11301
11302
11303
11304
11305
11306
11307
11311
11312
11313
11314
11315
11316
11321
11322
11323
11324
11325
11326
11331
11332
11333
11334
11335
11336
11337
11338
11341
11342
11343
11344
5 Kg
5 Kg
5 kg
5 Kg
5 kg
5 Kg
5 Kg
5 Kg
5 Kg
5 Kg
5 Kg
25 Kg
25 Kg
20 Kg
25 Kg
25 Kg
20 Kg
25 Kg
25 Kg
20 Kg
20 Kg
20 Kg
20 Kg
5 Kg
5 Kg
5 Kg
5 Kg
5 kg
20 Kg
10 kg
17 Kg
25 Kg
27 Kg
30 Kg
30 Kg
20 kg
10 kg
20 Kg
5 Kg
5 kg
20 Kg
Fast curing solvent free epoxy primer
Solvent Free Epoxy Primer
Solventless Epoxy Primer
Solvented Epoxy Primer
Poly urethane modified primer for FloorClad EPU /PFC/SL 2000PU
Moisture Insensitive Epoxy Primer for Damp Concrete Surfaces for WEC 3000/SL 5000WB
Moisture Insensitive Epoxy Primer for Metal Surfaces
Epoxy resin based moisture insensitive concrete bonding agent for horizontal and vertical
surfaces where mortar or concrete can be supported by formwork./ FloorClad SCS 50
Oil Resistant Primer
Acrylic Primer for Concrete Surfaces for FloorClad FPC/SP
Styrene Acrylate sealing primer for cementitious flooring materials for FloorClad SCS6/SCS12
Epoxy Patch Compound for Permanent Concrete Repairs
Self Levelling Epoxy based Mortar/Colour Screed @ 1.5mm-3mm
Heavy duty, flow applied, lightweight anti-skid floor Toppings
Epoxy based Mortar/Colour Screed @ 3mm -4mm
Epoxy based Mortar/Colour Screed @ 4mm -6mm
Impact/Load resistant Epoxy Mortar Screed @ 3mm -6mm
Epoxy based Seal Coat to level the porous /imperfection/depressions/irregularities in
epoxy mortar screed surface like FloorClad EMS 5000/FloorClad IRS5000
Fast Setting concrete Patching Compound
Cementitious Patching system for filling of wornout areas/holes or depressions in Concrete floors
Self Levelling Cementitious Screed @ 2mm-6mm
Self Levelling Cementitious Screed @ 6mm - 12mm
Self Leveling Cementitious Screed @ 10mm - 80mm
Epoxy modified cementitious floor screed for Light & medium duty abrasion resistant @ 3mm - 5mm
Epoxy Solvent Based Pigmented Floor Toppings Roller Coatings
Epoxy based Glossy Pigmented Floor Topping, Roller Coating
Moisture Compatible/tolerant Epoxy Coating
Polyurethane Glossy Floor Topping, Roller Coating
Epoxy Polyurethane based Floor Toppings, Roller Coatings
Acrylic floor sealer and concrete curing membrane
Self Levelling Epoxy Floor Topping @ 0.5mm thickness
Self Levelling Epoxy Floor Topping @ 1mm thickness
Self Levelling Epoxy Floor Topping @ 2mm thickness
Self Levelling Epoxy Floor Topping @ 3mm thickness
Self Levelling Epoxy Floor Topping @ 4mm thickness
Self Levelling Epoxy Floor Topping @ 5mm thickness
Self Leveling, damp-tolerant, water miscible, Epoxy toppings @ 2mm-5mm
Self Levlling Poly Urethane Floor Toppings @ 1.5 -2mm
Epoxy Coving compounds to prevent dust settlement
Epoxy Solvent Based Pigmented Floor Toppings Roller Coatings
Two Component PU based Cold Applied durable Marking paint
Anti Slip Grains for non Skid Flooring System for Roll on coatings
PRIMERS
MORTARS FOR PATCH REPAIRS/SCREEDS
RE-LAY/OVER-LAY ROLLER FLOOR TOPPINGS
Product Range
Ral Shade : http://monarchindia.net/RAL-Shade-card/ral.php
4. Typical Properties
1
2
3
4
5
6
7
8
9
10
Appearance
Base Type
Specific Gravity
Viscosity
Mix Ratio
By Weight
Mix Ratio
By Volume
Pot Life@25°C
VOC Content
Functional Cure
at 25°C
Coverage
~
~
~
min
~
~
min
%
Hrs
sq.m/Kg
Clear
Two Pack
Epoxy System
Componets
1.3
2-3
4(R):1(H)
4(R):1(H)
30 minutes
Nill
24
8Sq.m/ 1kg/
100mic/ coat
Transparent
Two Pack
Epoxy System
Componets
1.08
1-2
4(R):1(H)
4(R):1(H)
40-50 Minutes
Nill
24
7.5 Sq.m /1 Kg/
100 mic / coat
Slightly
Brown Liquid
Two Pack
Epoxy System
Componets
1.1
2-3
2(R):1(H)
2(R):1(H)
30
20
16
8Sq.m/ 1kg/
100mic/ coat
Slightly Yellow
Two Pack
Epoxy System
Componets
0.9
1
4(R):1(H)
3(R):1(H)
1 minute
40
4 hrs
7.5 Sq.m /1 Kg/
100 mic / coat
Transparent
Two Pack
Polyurethane
components
1.45
1-3
4(R):1(H)
4(R):1(H)
10 mins
Nill
18
7 Sq.m /1 Kg/
100 mic / coat
Red
Water Base
Epoxy System
Componets
1.06
2-3
1(R):2.5.(H)
1(R):2(H)
17 mins
20
5
6 Sq.m /1 Kg/
100 mic / coat
Slightly
Brown Liquid
Water Base
Epoxy System
Componets
1.07
1-2
1.6(R):1(H)
1.(R):1(H)
19 mins
Nill
4
7.5 Sq.m /1 Kg/
100 mic / coat
Milky White
Single Pack
Water Base
Styrene Acrylic
Primer
1.01
1-2
N/A
N/A
N/A
45
5
37 Sq.m / 5 kg /
100 mic / coat
Milky White
Single Pack
Water Base
Styrene Acrylate
Primer
1.02
1-2
N/A
N/A
N/A
40
4
10 m2 /
5kg / coat
Sl.No. Properties Unit MonoBond FP MonoBond EP MonoBond PP MonoBond ARMonoBond SFP MonoBond SEP MonoBond MIP Monobond SAPMonoBond MICP
Epoxy/Polyurethane Primers for Metal & Concrete Surfaces Moisture / Water /
Oil Insensitive Primers
Water based Primers for
Cementitious Floor Screeds
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Appearance
Base
Specific Gravity
Viscosity
Mix ratio
(Water Cement Ratio)
Pot Life@25 ° C
Functional Cure
Cured Shrinkage
Compressive Strength
@28 days
Tensile Strength
@28 days
Flexural Strength
@28 days
Abrasion Resistance
Cured Hardness
Bond Strength @7 days
Chemical Resistance
Water Absorbtion
Coverage
~
~
~
min
~
min
Hrs
cm/ cm
N/mm2
N/mm2
N/mm2
mg /No Cyclcs
Shore D
N/mm2
~
%
sq.m /
packsize
ASTM D 1544
Manual
ASTM D 1475-98
ASTM D 1200
Manual
IS 101
ASTM D 1640
ASTM D2566
ASTM D 695
ASTM D 638
ASTM D 790
ASTM D1044
ASTM D 2240
ASTM D 4541
ASTM 1038
ASTM D 570
~
Powder
Single
Component
Cementitious
System
2
Slurry
W/P--0.14
40
24
0.1
500
4
12
0.1
65
2.5
Good
3
0.5 sq.m/ 25 kg /
25 mm thick
Powder
Single
Component
Cementitious
System
2.2
Slurry
W/P--0.11
20
40
0.001
60
NA
NA
0.05
70
2
Good
3
1 Sq.m / 25 kg /
12 mm thick
Grey Powder
Single
Component
Cementitious
System
1.9
Slurry
W/P-0.26
20
24
0.01
35
1.2
9
0.008
65
2.5
Good
3.5
2 Sq.m /
20 kg / 6 mm
Grey Powder
Single
Component
Cementitious
System
2
Slurry
W/P=0.19
20
24
0.01
35
1.2
9
0.008
65
2.5
Good
2
1 Sq.m /
20 kg / 12 mm
Light Grey
Single
Component
Cementitious
System
2
Slurry
w/p 0.2
20
28
0.01
40
1.8
5
0.007
70
1
Good
2
0.9 sq.mt/
20 kg/12 mm
Grey
Three
Component
Cementitious
System
1.9
Slurry
N/A
40
24
0.01
30
4
14
0.008
75
2
Good
2
3.5 Sq.mt /
20 kg/3 mm
Sl.No. Properties FloorClad SPFloorClad FPCUnitStandard FloorClad SCS6 FloorClad SCS12 FloorClad LC FloorClad WEC 3000
Cementitious based mortars for floor patch repairs/self leveling floor screeds
5. 1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Appearance
Base Type
Specific Gravity
Viscosity
Mix Ratio By Weight
pH Value
Pot Life@25 ° C
Functional Cure
Cured Shrinkage
Compressive Strength @ 7 days
Tensile Strength @ 7 days
Flexural Strength@ 7 days
Abrasion Resistance 1000°c
Cured Hardness
Bond Strength @7 days
Chemical Resistance
Water Absorbtion
Coverage
~
~
~
min
~
~
min
Hrs
cm/ cm
N/mm2
N/mm2
N/mm2
mg /1000 Cyclcs
Shore D
N/mm2
~
%
sq.m/
packsize
ASTM D 1544
Manual
ASTM D 1475-98
ASTMD 1200
Manual
ASTM D 1293
IS 101
ASTM D 1640
ASTM D2566
ASTMD 695
ASTMD 638
ASTMD 790
ASTM D1044
ASTM D 2240
ASTM D 4541
ASTM 1038
ASTM D 570
~
Slightly Brown
Three Part
Epoxy System
1.8
Slurry
2(R):1(H): 23
6-8
30
16
0.005
90
11
20
0.01
90
3
Excellent
1
1.25 Sq.m /
25 kg / 10 mm
Slightly Brown
Three Part
Epoxy System
1.65
Slurry
2(R):1(H):6(A)
6-8
45
16
0.03
85
11
22
0.008
80
1.5
Excellent
1
7 Sq.m /
25 kg / 2 mm
Viscous Liquid
Three Part
Epoxy System
1.8
Slurry
1(R):1(H):4.6(A)
6-8
30
24
0.005
78
6
8
0.007
90
2
Excellent
1
2.7 Sq.m/
20 Kg / 4mm
Slightly Brown
Three Part
Epoxy System
1.8
Slurry
2(R):1(H):9(A)
6-8
45
16
0.005
78
11
21
0.008
85
1.5
Excellent
2
4.6 Sq.m /
25 kg / 3 mm
Grey
Three Part
Epoxy System
1.9
Slurry
2.7(R):1(H):25(A)
~
30
12
0.006
100
20
40
0.24
83
2
Excellent
2
2 sq.mt/
1 tr /3 mm
Sl.No. Properties FloorClad EPCUnitStandard FloorClad SEMS FloorClad 2050
FloorClad EMS
5000
FloorClad IRS
5000
Epoxy based mortars for floor patch repairs/self leveling floor screeds
Typical Properties
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Appearance
Color
Base Type
Specific Gravity
Viscosity
Mix Ratio By Weight
Gloss
Pot Life@25 ° C
Voc Content
Functional Cure
Cured Shrinkage
Compressive Strength
@ 7 days
Tensile Strength @ 7 days
Flexural Strength
@ 28 days
Abrasion Resistance
Cured Hardness
Elongation @ Break
Bond Strength @7 days
Chemical Resistance
Water Absorbtion
Coverage
ASTM D 1544
~
Manual
ASTM D 1475-98
ASTMD 1200
Manual
ASTM D 523
IS 101
ASTM D1353
ASTM D 1640
ASTM D2566
ASTMD 695
ASTMD 638
ASTMD 790
ASTM D1044
ASTM D 2240
ASTM D638
ASTM D 4541
ASTM 1038
ASTM D 570
~
~
~
~
~
min
~
~
min
%
Hrs
cm/ cm
N/mm2
N/mm2
N/mm2
mg /No Cyclcs
Shore D
%
N/mm2
~
%
sq.m/
pack size
Viscous Liquid
Custom Color
Two part
Epoxy system
1.34
3 mins(R) ;60 secs (H)
2.6(R):1(H)
12
70
55
24
0.01
80
13
12
1.7
75
N/A
2
Good
2
25sq mt/ 5 Kg/
200 mic /2 coat
Viscous Liquid
Custom Color
Four Part
Epoxy System
1.56
8 mins(R) ;60 secs (H)
4(R):1(H):3(A)
83
45
Nill
24
0.002
78
1.2
9
2.5
80
N/A
1.5
Excellent
2
16 Sq.m/ 5 kg /
200 mic / coat
Viscous Liquid
Custom Color
Three Part
Epoxy System
1.64
7mins(R) ;58 secs (H)
1(R):1(H)
9
30
Nill
24
0.005
78
6
8
2
65
N/A
3
Good
2
18 Sq.m/ 5 Kg /
180 mic / coat
Viscous Liquid
Custom Color
Three Part
Polyurethane System
1.42
10 mins(R) ;55 secs (H)
5(R):1(H)
18
45
Nill
24
0.01
78
11
22
1.8
80
N/A
1.5
Excellent
2.5
14 Sq.m / 5 kg /
250 mic / coat
Viscous Liquid
Custom Color
Three Part Epoxy
Polyurethane System
1.25
5 mins(R) ;55 secs (H)
4.4(R):1(H)
80
45
Nill
24
Nill
78
11
2s
1.8
70
N/A
1.9
Good
2
5 Sq.m / 5 Kg /
1 mm / coat
Viscous Liquid
Custom Color
Two Part
Acrylic System.
1.12
6 mins(R) ;57 secs (H)
Single Component
8
45
25
24
0.001
78
11
2
0.008
65
N/A
1.5
Good
2
160 Sq.m /
20 kg / Coat
Sl.No. Properties UnitStandard Floor Clad DC FloorClad EFC FloorClad MEC FloorClad PFC FloorClad EPU FloorClad FS
Epoxy / Polyurethane Floor Toppings - Re - Lay / Over - Lay Roller Coat
7. Application Area
Bathrooms
Swimming pools
Restaurants
Bacteria and other harmful micro organisms
Schools
Auditorium
University
Research laboratories
Wearhouse Floors
Automobile
Beverages
Biotech plants
Marine
Chemical Industries
Food processing units
Metal Processing & Engineering Plants
Oil Reöneries
Paper & Pulp Indstries
Soft Drinks & Bottling Plants
Steel Plants
Sugar Factories
Textile production bleaching & dying areas.
Water and Sewage treatment plants
Pharmaceutical plants
Dairies
Meat packaging units
Printing Plants
Airport Hangers
Battery Rooms
Bulk Storage & Logistics Areas
Bulk storage
Exposed aggregate concrete
Clean rooms
Cold storage facilities down to -5°C
Control room
Curing Membrane For fresh Concrete
Damged Floor Areas
Foot and Road bridges
Garages
Industrial Wet/Dry Areas
Multi-level car parks
Packaging lines
Plant rooms
Processing area
Production Processing areas
Repair from chemical spillage, oil spillage
Shower rooms
Ships decks
Steam cleaning areas
Sterile areas
Traffic aisles in factories or warehouses
Walk ways
Wash down area
Petrol Bunk
Workshops/Machine Shops
work platforms
Hospitals and Operation theaters
Commercial storage facilities
Gyms
Health care units
Shopping Malls
Retail Facilities
Theme Parks
Residential & Office Application
Institutional Application
Industries
Commercial Application
Under Layment for Vinyl sheets & Tiles & carpets
Corridors.
Convention Centers
Kitchens
Galleries
Test & Inspection laboratories
Laboratories
Formulation Units
Colleges
Multiplexes
Drive aisles
Paint Shops
Car park/ deck coating/ Access Ramps
Helicopter decks
Loading Bays
Cafeterias
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
8. FloorClad EPC
Epoxy Patch Compound for Permanent Concrete Repairs
FloorClad EPC is a three part solvent-free combination of epoxy resin, modiöed amine hardeners ölled
withspeciallygradedandselectedhighcrushingstrength,chemicallyinertaggregatesUsedforpermanentrepairs
to concrete structure and cementitious substrates where strength, impermeability to water and resistance to
aggressive chemicals is essential. Ideally suited for maintaining engineering, chemical handling and processing
plants. It is applied by trowel as a durable chemical resistant repair mortar. The minimum thickness is 5mm. The
maximumthicknessis50mm.
FloorClad NSC
Heavy duty, øow applied, lightweight anti-skid surface dressing
Slurrysystemisbasedoncoaltarmodiöedepoxyresinsthatforaøuid,homogenousslurryandprovidesa
lightweight, yet extremely hardwearing anti-skid surface to a variety of substrates including steel, concrete, and
timber Ideally suited for foot and road bridges, RO link spans, helicopter decks, work platforms, ships decks, car
parks, walkways, wet work industrial areas etc. Special non-spark formulations and low øame spread make
FloorCladNSCslurrysystemespeciallysuitableforoffshoreoilplatforms.
FloorClad SEMS
Self Levelling Epoxy based Mortar/Color Screed @ 1.5mm-3mm
The smooth impervious surface önish provides an easily cleaned and hygienic surface with excellent
resistance to chemical and mechanical attack provided as a thin layer topping underlayment for FloorClad epoxy
toppings.The mixed material should be applied on to the prepared and primed øoor using a notched or øat trowel
to a typical thickness of 1.5mm minimum. The surface should be spike rolled to remove the entrapped air. Ensure
applicationisacontinuousoperationandlayingiswithin15minutesofmixingandspikerolledwithin5minutesof
laying.
The mixed mortar can easily be laid by trowel to a joint less, abrasion and chemical resistant topping.
Wheresituationdemands,theaggregatecontentcanbereducedtoyieldaself-sealingmortar.
Epoxy based mortars for ø oor patch repairs/ø oor screeds
9. FloorClad EMS 3000
Epoxy based Mortar/Color Screed @ 3mm -4mmFloorClad EMS 5000
FloorClad EMS3000 is a three part solvent-free combination of epoxy resin, modiöed amine hardeners
ölled with specially graded and selected high crushing strength, chemically inert aggregates. The cured mortar
offers an extremely high strength øoor screed with exceptional resistance to the surface mechanical wear and
attack from chemical spillage, is impervious and, at the same time, has a safe non-slip önish for personnel and
vehicular traffic. It is laid by trowel as a durable chemical resistant screed at 3 to 4 mm thickness depending on the
requirement. It is ideal for re-proöling worn and damaged øoors when applied to concrete surface, it provides a
non-skidhighstrengthøooringcapableofwithstandingextremelyhighloadingandwear.
FloorClad IRS 5000
Impact/Load resistant Epoxy Mortar Screed @ 3mm -6mm
FloorCladIRS5000,isathreepartsolvent-freecombinationofepoxyresin,modiöedaminehardenersölled
with specially graded and selected high density and impact strength aggregates, providing an extremely high
strength øoor topping with exceptional resistance to surface mechanical wear and safe nonslip önish with good
gripping surface to both vehicular and pedestrian traffic. The trowelled epoxy resin tough screed is ideally suited
for heavy duty traffic like heavy engineering industry, paper and pulp industry, steel works, automobile industry,
tiremanufacturingindustry,warehouses,truckinglanes,loadingbaysetc.,
FloorClad EMS 5000
Epoxy based Mortar/Colour Screed @ 3mm -6mm
FloorClad EMS 5000 is a three part solvent-free combination of epoxy resin, modiöed amine hardeners
ölled with specially graded and selected high crushing strength, chemically inert aggregates. The cured mortar
offers an extremely high strength øoor screed with exceptional resistance to the surface mechanical wear and
attack from chemical spillage, is impervious and, at the same time, has a safe non-slip önish for personnel and
vehicular traffic. It is laid by trowel as a durable chemical resistant screed at 3 to 6 mm thickness depending on the
requirement. It is ideal for re-proöling worn and damaged øoors when applied to concrete surface, it provides a
non-skidhighstrengthøooringcapableofwithstandingextremelyhighloadingandwear.
10. FloorClad SC
Epoxy based Seal Coat
Epoxy based Seal Coat to level the porous /imperfection/depressions/irregularities in epoxy mortar
screedsurfacelikeFloorCladEMS5000/FloorCladIRS5000
FloorClad SP
Restores the appearance of honeycombed or surface impaired concrete
FloorClad SP mortar is supplied as a ready to use dry powder requiring only the addition of water to
produce a high strength mortar with non-shrink property along with controlled expansion characteristics. It is
used for patching and replacement of worn out areas, ölling of holes or depressions in concrete øoor slabs in
factories,godowns,commercialordomesticbuildings
MonoBuild FPC
Fast Setting concrete Patching Compound
FloorClad FPC mortar is supplied as a ready to use dry powder requiring only the addition of water to
produce specially designed to provide a very fast set repair in concrete øoors and pavements and is particularly
useful where traffic must be kept øowing.The quick setting mortar will accept pedestrian and vehicular traffic in 2
hours.FloorCladFPCmortarwillbeofparticularinteresttoindustrialmaintenanceengineers,transportmanagers,
airportauthoritiesoranyplacewherethatpotholesinconcretecauseahazardtopedestrianandwheeledtraffic.
Cementitious based mortars for ø oor patch repairs/self leveling ø oor screeds
11. FloorClad SCS6
Self Levelling Cementitious Screed @ 2mm-6mm
FloorClad SCS6 is supplied as a dry, grey powder which requires only the addition of water to produce a
smooth free øowing and self levelling material which can be laid to a feather edge. This provides an ideal fairing
material for levelling uneven, in situ or precast concrete øoors. FloorClad SCS6 provides a self levelling,
cementitious sub øoor/ underlay for a wide variety of øoor önishes which require a smooth level substrate, such as
tiles, carpeting, vinyl sheeting, linoleum, rubber and other sheet øooring. Additionally, it can be used directly on in
situorprecastøoorstoprovidesmoothlevelsurfacewithoutscreeding.
FloorClad SCS50
Self-leveling, cementitious øoor levelling compound, 12mm to 50mm
FloorClad SCS50 is supplied as a dry, grey powder which requires only the addition of water to produce a
smooth free øowing and thick bed self levelling material as industrial wearing course or for reprooöng of existing
øoors for use in areas that are subjected to both foot and forklift traffic within 10 hours. This is especially useful
where speciöed øoor tolerances have not been achieved or where, for speed of installation, the concrete øoor has
been left with a tamped önish such as Warehouses, Light to medium engineering operations, Car park etc.,
FloorCladSCS50canbeappliedinexcessof50-80mm,with20mmstoneaggregateatspreadrateof3-5Kg/m².
FloorClad SCS12
Self Levelling Cementitious Screed @ 6mm - 12mm
FloorClad SCS12 is supplied as a dry, grey powder which requires only the addition of water to produce a
smooth free øowing and self levelling material as industrial wearing course or for reinstatement of existing øoors
for use in areas that are subjected to both foot and forklift traffic. This is especially useful where speciöed øoor
tolerances have not been achieved or where, for speed of installation, the concrete øoor has been left with a
tamped önish such as Warehouses, Light to medium engineering operations, Car park etc., FloorClad SCS12
providesaselflevelling,cementitioussubøoor/underlayforawidevarietyoføoorönisheswhichrequireasmooth
level substrate, such as tiles, carpeting, vinyl sheeting, linoleum, rubber and other sheet øooring. Additionally, it
canbeuseddirectlyoninsituorprecastøoorstoprovidesmoothlevelsurfacewithoutscreeding
12. FloorClad WEC3000
Light & medium duty abrasion resistant epoxy modiöed
cementitious øoor screed topping.
FloorCladWEC3000isa4partepoxymodiöedcementitiousøoorscreedøooring,providesahighstrength
øoor topping with very good resistance to surface mechanical wear . It has a safe nonslip önish for personnel and
vehicular traffic. In areas where high degree of cleanliness is required the surface of FloorClad WEC3000 can be
sealed with FloorClad EFC or any other FloorClad epoxy resin øoor coating systems Ideally suited for dry areas in
engineering plants, oil reöneries and paint workshops and also for wet areas such as dairies, food industries,
breweriesetc.,thatarecontinuouslyexposedtowater.
FloorClad EFC
Epoxy based Glossy Pigmented Floor Topping, Roller Coating
FloorCladEFCisasolventfreeHighBuildEpoxyCoating,comprisingoftwotopcoatseachtopcoattobea
minimum of 200 microns thick. It is ideally suited for use in wet areas where a high degree of resistance to
chemicals,oilsandgreaseandpossiblespillageisforeseen.
FloorClad DC
Decorative and aesthetic epoxy resin øoor coating
FloorClad DC is easily cleaned, attractive øoor coating in areas where high resistance to chemical attack is
required.Itcanalsobeusedasaönalcoatingandsealerforepoxyøoorscreedstoprovideamoredurableandeasily
cleanedsurfaceforapplicationintwocoatstoachieveatotaldryölmthicknessof90microns.
Epoxy / Polyurethane Floor Toppings - Re - Lay / Over - Lay Roller Coat
13. FloorClad MEC
Water dispersed epoxy coating and sealer
Floor Clad MEC is a water dispersed epoxy coating designed for damp tolerant, anti-fungal and water
vapor permeable coating. The product is odorless and can be applied onto cementitious and concrete surfaces
providing dustproof coatings.The cured ölm is easily cleanable and resistant to penetration of oils and liquids. The
product forms a waterproof barrier and is non-toxic. It is resistant to corrosion, chemicals and abrasion. It is
additionally used as a thin coat application for the areas subject to light vehicle and pedestrian traffic.The product
is ideal for contact with water intended for human consumption.The water permeability allows it to be applied on
damp substrates and green concrete. However this should not be subjected to øowing / running water/over
wateredconditions.
FloorClad EPU
Epoxy Polyurethane based Floor Toppings, Roller Coatings
FloorClad EPU is a hybrid polyurethane based, resin øoor coating for use in wide range of industrial
environments where a lasting to low maintenance øoor is required. It is ideally suited for use in areas where a high
degreeofresistancetochemicals,oilsandgreaseisrequired.Theproductcomprisesoftwotopcoatseachtopcoat
tobeaminimumof200micronsthick.
FloorClad PFC
Polyurethane Glossy Floor Topping, Roller Coating
FloorCladPFCisacombinationofpolyolresin,isocynatehardenersölledwithspeciallygraded,chemically
inert aggregates, with a high mechanical strength. The cured ölm is very resilient and able to withstand severe
chemical resistance where a smooth, even and easy to clean surface is required.The product has excellent UV light
stablepropertieswithgoodøexibilityandhardwearing.
14. FloorClad FS
Acrylic øoor sealer and concrete curing membrane
Singlecomponent,penetratingsyntheticacryliccoatinghasexcellentadhesiontocementationssurfaces
and, when cured, forms a semi-gloss øexible ölm. The coating can be applied by simple brush, squeegee, roller or
sprayapplication.Itisnon-yellowingandsuitableforexteriorandinteriorapplication
Thecuredölmhas2properties,FloorSealer&DustProoöngandConcreteCuringMembrane.
The2coatapplicationprovideasealingcoatoncementationsøoorsand moreeasilycleanedsurfacewith
resistance to the penetration of various liquids. The coating helps to control dusting and hence ideal for dust
prooöng warehouses, garages, indoor car parks and light industrial buildings. Prevents dusting by sealing the
surface
Thesinglecoatapplicationforoptimumcuringandsealingoffreshlyplacedconcreteøoorsandstructures
inordertolimitsurfacedryingandcracking.Ithasexcellentmoistureretention.
FloorClad SL 500
Self Levelling Epoxy Floor Topping @ 0.5mm thickness
Floor sealer & Dust Prooöng:
Concrete curing membrane:
FloorClad SL500 is designed for use in wide range of industrial environments where a lasting solution to
øoor maintenance problems is required. It provides a dense, impervious, colored and chemically resistant øoor
surface which is hygienic and easy to clean. It provides a smooth, light-reøective surface. The product is
recommendedforlightdutyfoot,trolley,pallettruckandrubberwheeledforklifttraffic.
FloorClad SL 1000
Self Levelling Epoxy Floor Topping @ 1mm thickness
FloorClad SL1000 is designed for use in wide range of industrial environments where a lasting solution to
øoor maintenance problems is required. It provides a dense, impervious, colored and chemically resistant øoor
surface which is hygienic and easy to clean. It provides a smooth, light-reøective surface. The product is
recommendedforlightdutyfoot,trolley,pallettruckandrubberwheeledforklifttraffic.
High Performance Self Leveling Floor Toppings
15. FloorClad SL 2000
Self levelling 2 mm thick epoxy resin based colored øoor topping
FloorClad SL2000 is designed for use in wide range of industrial environments where a lasting solution to
øoor maintenance problems is required. It provides a dense, impervious, colored and chemically resistant øoor
surface which is hygienic and easy to clean. It provides a smooth, light-reøective surface. The product is
recommendedforlightdutyfoot,trolley,pallettruckandrubberwheeledforklifttraffic.
FloorClad SL 4000
Self levelling 4 mm thick epoxy resin based colored øoor topping
FloorClad SL4000 is designed for use in wide range of industrial environments where a lasting solution to
øoor maintenance problems is required. It provides a dense, impervious, colored and chemically resistant øoor
surface which is hygienic and easy to clean. It provides a smooth, light-reøective surface. The product is
recommendedforheavydutyfoot,trolley,pallettruckandrubberwheeledforklifttraffic.
FloorClad SL 3000
FloorClad SL 5000
Self levelling 3 mm thick epoxy resin based colored øoor topping
Self levelling 5 mm thick epoxy resin based colored øoor topping
FloorClad SL3000 is designed for use in wide range of industrial environments where a lasting solution to
øoor maintenance problems is required. It provides a dense, impervious, colored and chemically resistant øoor
surface which is hygienic and easy to clean. It provides a smooth, light-reøective surface. The product is
recommendedformediumdutyfoot,trolley,pallettruckandrubberwheeledforklifttraffic.
FloorClad SL5000 is designed for use in wide range of industrial environments where a lasting solution to
øoor maintenance problems is required. It provides a dense, impervious, colored and chemically resistant øoor
surface which is hygienic and easy to clean. It provides a smooth, light-reøective surface. The product is
recommendedforheavydutyfoot,trolley,pallettruckandrubberwheeledforklifttraffic.
16. FloorClad SL5000WB
Self-Leveling, damp-tolerant, water miscible, Epoxy toppings on
horizontal substrates @ 2mm-5mm
FloorClad SL5000WB provides smooth, dense, matt önish, fast curing and water vapor permeable seal to
concrete. The cured ölm is resistant to most oils and liquids as well as to abrasion and impact. The permeability of
concreteallowsittobeappliedondampsubstratesandgreenconcrete(1dayold).
FloorClad EC
Epoxy Coving compounds to prevent dust settlement
Theepoxybased3componentcovingsystemtoformøoor-walljoint,perimeteredgesizeof2”,3”and4”for
sanitarysealtopreventdustsettlementinøoorsandwalls.
FloorClad SL2000PU
Self-leveling, 2 mm chemical and abrasion resistant polyurethane
øoor screed.
SL2000PU is 4 part system, that is laid by serrated trowel, provides an impermeable, hard øoor topping
with exceptional resistance to mechanical wear and chemical spillages. The cured topping produces a non-slip
surfaceforpedestrianandwheeledtrafficespeciallybreweries,dairies,softdrinksproductionetc.
MonoMark DC
Epoxy based, øoor line marking coating compound
Highly visible and long lasting walkways, gangways, aisles and line marking is a time and cost effective
solution to indicate safe traffic management plans and to clearly demarcate hatched and work areas. The
prevention of workplace hazardous incidences continues to be paramount for all industries as they aim to ensure
an efficient, safe and injury free environment. A business's ability to highlight designated pedestrian and vehicular
traffic areas is an essential component in eliminating accidents involving machinery and vehicles. Line markings
can also be applied to epoxy øoor coatings applied resin øoors for fork lift identiöcation, pallet drop locations,
Machinerylocation,Manwalkingwaysetc.,
Ancillary Flooring Products
17. MonoMark PU2K
Polyurethane based, øoor line marking coating compound
Highly visible and long lasting walkways, gangways, aisles and line marking is a time and cost effective
solution to indicate safe traffic management plans and to clearly demarcate hatched and work areas. The
prevention of workplace hazardous incidences continues to be paramount for all industries as they aim to ensure
an efficient, safe and injury free environment. A business's ability to highlight designated pedestrian and vehicular
traffic areas is an essential component in eliminating accidents involving machinery and vehicles. Line markings
can also be applied to epoxy øoor coatings applied resin øoors for fork lift identiöcation, pallet drop locations,
Machinerylocation,Manwalkingwaysetc.,
FloorClad ANS
Anti-Slip Grains for non-Skid Flooring System for Roll on coatings
Anti-slip grains for slip and wear resistance for concrete øoors. They are speciöcally designed for sprinkle
on applications over øoor toppings to achieve maximum slip resistance. The embedded grains are not liable to
break up under traffic conditions and hence most ideal for use on wet surfaces. These grains are suitable for
Schools, Hospitals, Public buildings, Factories, On öre escapes, Stairways, Entrances, Loading ramps, Machine
surrounds etc., in combination with FloorToppings such as FloorClad DC, FloorClad EFC, FloorClad MEC, FloorClad
PFC,FloorCladEPUetc.,
Clientele List
: monarchindia.net : contact@monarchindia.net : +(91)-9600992069
DEALERSHIP ENQUIRIES SOLICITED - Excellent Returns Assured
Follow us on :