AVERMETRICS www.avermetrics.com designs and manufactures unique Pro-Audio/MI production test equipment, by far superior, especially when compared to other solutions such as Audio Precision, Prism, or National Instruments.
The Avermetrics test system is faster for production testing, and even more so when testing multiple channels, since the system is built to test all channels simultaneously, instead of only one or two channels at a time.
The following endorsement was made by a well-known contract manufacturer who currently uses the Prism and AP Testers:
“We are using in our Manufacturing line the AVERMETRICS Test & Measurement System in our Pro-Audio production lines to test our products since Nov, 2014. Last year and again recently, we studied the performance of the production lines using AVERMETRICS testers, compared it to the previous test methods which we had used, before we installed your modular testers. We have realized that the test time needed is much less now, in some cases coming down by a factor of 5 or more, and the AVERMETRICS Tester also creates very stable results. We are looking forward to another meeting with you so that we can discuss using your newly announced modules and even more AVERMETRICS test systems for our other production lines. Thanks for your great support!”
AVERMETRICS is currently also designing and developing additional test modules, such as Digital Multimeter Modules, etc.
You can download the Product Brochure from the AVERMETRICS Web Site.
Avermetrics Production Test & Measurement Equipment reduces significantly the Test Times.
1. 1116 Colorado Blvd., Los Angeles, CA 90041
T: (323) 230-0515 | F: (323) 704-3316
info@avermetrics.com | www.avermetrics.com
The Avermetrics™ Test and Measurement System
has been engineered from the ground up for produc-
tion line testing of electronic products, subassemblies,
boards, and components. It was designed by an engi-
neering team with extensive product development and
testing experience, with performance and the total cost
of testing as clear design criteria.
This system, and the currently available range of plug-
in modules, offers a wide range of test capabilities,
from professional, semi-professional, and consumer
audio product testing, to basic board level tests, to pro-
cess control, and more. New modules to add new tests
are being added to the library every day.
Modular System
This is a modular system using a custom 1U rack
designed to hold up to 4 modules. The system is highly
scalable: Racks may be interconnected using the
AVERLINK™ connectors on the back of each rack unit;
up to 64 rack units holding up to 254 modules can be
connected in a single system. Internally, each module
has an array of processors, and the system is organized
as a large, interconnected two-dimensional array of
these processors in a distributed intelligence configu-
ration. Because each module is intelligent it does its
own analysis, so tests across multiple modules occur in
parallel, significantly reducing testing time.
Communication
XOS™ is an XML-based operating system that is at
the core of the test system. To define tests or do other
operations, a host computer sends simple XML com-
mands via Telnet. The XOS operating system interprets
these commands, routes them to the proper module
or modules, collects the results, and sends them back
to the host computer in an easy-to-parse XML format.
Literally any programming language and operating
system that can open a networking socket will support
XOS and this system.
Software Support
Avermetrics supplies documentation, C++ classes that
handle all aspects of communication with the system
and parsing of XML commands and results, and exam-
ple applications (with complete source code) to get you
started. One of those example applications, AverTest,
provides full-featured test execution using simple XML
test and limit definition files so you can start testing on
the production line right away.
Future Proof
The system supports a complete Device Firmware Up-
date capability so new features and updated firmware
can be programmed into existing systems in the field,
with no downtime. Adding new tests and more chan-
nels is as simple as plugging new modules and racks
into an existing system. Your investment in testing
never goes obsolete.
Modules
Currently, there are six different modules available to
test audio and analog signals, and to control process
operation and interact with external sensors and digi-
tal signals. More information and pricing for each of
these modules is below.
P/N 770-00004-0003
2. 9140 1U Rack Unit
Every system has at least one 9140 Rack unit. Up to 64
rack units may be interconnected to create large, uni-
fied test systems for multi-channel audio and diverse
testing requirements. Each rack accepts four modules.
Two AVERLINK ports (A and B) are supplied on the
back panel. Interconnect racks by connecting A to
B or B to A using the supplied Cat5 cables. (See the
Hardware Installation manual for more information on
interconnections between racks.)
Dimensions (w/o Rack Ears, no
modules)
440mm x 242mm x 44.45mm
(17.3in x 9.5in x 1.75in)
Weight (no modules) 3.86 kg (8.5 lbs)
Input 90Vrms to 240Vrms, 47 to
63Hz, Single Phase
Input Power (maximum) 100W
Cost
9140 Rack Unit $750
US NEMA 5-15P Power Cord N/C
UK BS1363 UK3 Power Cord N/C
3001 Ethernet Host Adapter
Every system has one (and only one) Ethernet Host
Adapter module. This module provides communica-
tion between the system and host computer, and per-
forms test scheduling and results formatting tasks dur-
ing test execution. Communication with the module is
done via Telnet, and an embedded web server provides
access to configuration settings and status information.
A white front panel LED indicates system activity and
status.
Dimensions (maximum) 170mm x 107mm x 44.45mm
(6.7in x 4.2in x 1.75in)
Weight 156 g (5.5 oz.)
Ethernet Support 100Base-T via RJ-45, AutoIP,
mDNS, Auto MDIX, DHCP,
Static IP
Front Panel LEDs White, system activity; Green,
link on, Yellow, blink on link
activity.
Default mDNS Address xos.local
Cost
3001 Ethernet Host Adapter $750
4021 Analog Audio Input Module
Any number of 4021 Input modules may be installed
in a given system. This module provides two high-per-
formance audio inputs, supporting tests over the entire
audio spectrum and a wide range of signal levels. Each
channel operates simultaneously and independently,
doubling effective throughput compared to conven-
tional audio test systems. Multiple modules in a sys-
tem all operate in parallel, greatly reducing test time
for multi-channel measurements when compared to
switched, repetitive testing.
Signal inputs are via balanced XLR connectors. Single-
ended signals are supported by grounding the cold in-
put (pin 3) to ground (pin 1) and driving the hot input
(pin 2) relative to ground. Ground lift is also selectable
for completely floating balanced inputs.
Currently available native tests are: FFT (32 to 65536
points), Level, DR, SNR, THD+N.
Dimensions (maximum) 170mm x 107mm x 44.45mm
(6.7in x 4.2in x 1.75in)
Weight 348 g (12.3 oz.)
Input Level, maximum +32 dBu
Autorange (in 6dB steps) 10 ranges, +32 dBu to -22
dBu full scale.
THD+N, +32 dBu to 0 dBu, @
1 kHz, typical
-114 dB
THD+N, -1 dBu to -28 dBu, @
1 kHz, typical
-110 dB
THD+N, 10 Hz to 22 kHz @
+26 dBu, minimum
-108 dB
Dynamic Range, @ 1 kHz,
autorange enabled, minimum
145 dB
Signal to Noise, @ 1 kHz, au-
torange enabled, minimum
145 dB
Dynamic Range, @ 1kHz, au-
torange disabled, typical
126 dB
Signal to Noise, @ 1 kHz, au-
torange disabled, typical
126 dB
Frequency range, rated perfor-
mance
10 Hz to 22 kHz
Level accuracy and flatness,
integration >= 1000
+/- 0.02dB
Cost
4021 Analog Audio Input Module $2500
3. 4121 Analog Audio Generator Module
Any number of 4121 Generator modules may be
installed in a given system. This module provides two
high-performance audio outputs, providing audio
stimulus signals over the entire audio spectrum and at
a wide range of signal levels. Each output may be set to
different frequencies and/or levels. Three very low dis-
tortion oscillators are available for generating complex
stimulus signals and may be assigned in any combina-
tion to either or both outputs.
Dimensions (maximum) 170mm x 107mm x 44.45mm
(6.7in x 4.2in x 1.75in)
Weight 226 g (8 oz.)
Output Level, maximum +26 dBu
Autorange (in 6dB steps) 9 ranges, +26 dBu to -22 dBu
full scale.
THD+N, +26 dBu to 0 dBu, @
1 kHz, typical
-108 dB
THD+N, -1 dBu to -28 dBu, @
1 kHz, typical
-104 dB
THD+N, 10 Hz to 22 kHz @
+26 dBu, minimum
-104 dB
Dynamic Range, @ 1 kHz,
autorange enabled, minimum
145 dB
Signal to Noise, @ 1 kHz, au-
torange enabled, minimum
145 dB
Dynamic Range, @ 1kHz, au-
torange disabled, typical
128 dB
Signal to Noise, @ 1 kHz, au-
torange disabled, typical
128 dB
Frequency range, rated perfor-
mance
10 Hz to 22 kHz
Level accuracy and flatness +/- 0.02dB
Output Impedance, nominal 10Ω
Relay, rated life 109
cycles
Cost
4121 Analog Audio Generator Module $1500
Options
001 Enhanced THD+N (-110dB, typical) Add $500
014 Output Impedance 40Ω Add $100
015 Output Impedance 150Ω Add $100
016 Output Impedance 600Ω Add
$100
9001 Filler Module
Rack units require that all four slots be filled with
modules to ensure proper internal communication and
signal integrity. For rack units with fewer than four
modules to meet this requirement each unused slot
is filled with a filler module, which provides needed
signal routing and termination.
Cost
9001 Filler Module $125
Supplied with a factory-provisioned system N/C
3101 Isolated I/O Module
This module provides eight opto-isolated inputs ,eight
reed relay SPST outputs, and a fully isolated power
supply. This supply can provide power for small exter-
nal sensors and other test-fixture circuits, and in some
situations may simplify external connections to the
system.
Because the inputs, outputs, and power are all com-
pletely isolated from the system ground and internal
signals, this module is perfect for controlling processes
in noisy environments or adjusting sensitive analog
signals internal to test devices.
The eight opto-isolated inputs can be used to sense the
state of external signals, such as proximity switches,
out of limit sensors (overtemp, overvoltage, etc.),
switch closures, test status, and other binary events.
Similarly, the eight reed relay outputs can be used to
close circuits during board-level tests, actuate motors,
valves, or other process control components, light an-
nunciators, etc. These are very high reliability relays;
they are rated at 109
cycles at low signal levels, and can
handle up to 10W.
Eight Green LEDs indicate the state of the opto-iso-
lated input signals, while eight Red LEDs indicate the
state of the reed relay outputs for easy visual feedback.
The isolated power supply provides up to 100ma of
current across any of the available 12V, 5V, and 3.3V
outputs. All outputs are short-circuit protected and
current limited. Power is available on both the input
and output connectors.
4. Dimensions (maximum) 170mm x 107mm x 44.45mm
(6.7in x 4.2in x 1.75in)
Weight 246 g (8.7 oz.)
Actuation current, opto-isolat-
ed inputs, minimum
4ma
Opto-isolator input, forward
voltage, typical
1.3V
Opto-isolator input, reverse
voltage, maximum
100V
Relay, rated life 109
cycles, 1V@10ma
Relay, maximum open voltage 200V
Relay, maximum closed cur-
rent
0.5A
Relay, static resistance 0.2Ω
Insulation Breakdown Voltage,
minimum
500V
Input connector DB-25 Female D-Sub
Output connector DB-25 Male D-Sub
Cost
3101 Isolated I/O Module $900
3102 Digital I/O Module
The 3102 Digital I/O Module is identical to the 3101
module, with the omission of the isolated power sup-
ply. All other specifications and features are identical to
the 3101 module.
Cost
3102 Isolated I/O Module $750
3103 Digital I/O Module
This module provides eight opto-isolated inputs and 32
digital voltage level outputs, along with a dual bidirec-
tional SPI control port. This module is ideal for control
of external test sets, test devices, and manufacturing
processes.
The opto-isolated inputs are identical to those on the
3101/3102 Isolated I/O modules. No power is supplied
by this module to drive external circuitry, other than
what is available directly from the digital outputs.
The outputs are selectable (in 8-bit banks) between
3.3V and 5V logic levels. These are high-current out-
puts and can source or sink up to 12ma each.
The SPI connector has MISO, MOSI, SCK, and two
CS signals and can support two bidirectional SPI ports
for control and initialization of test devices and/or test
sets. These signals are independent of the 32 digital I/O
outputs and opto-isolated inputs.
Dimensions (maximum) 170mm x 107mm x 44.45mm
(6.7in x 4.2in x 1.75in)
Weight 242 g (8.5 oz.)
Actuation current, opto-isolat-
ed inputs, minimum
4ma
Opto-isolator input, forward
voltage, typical
1.3V
Opto-isolator input, reverse
voltage, maximum
100V
Insulation Breakdown Voltage,
input, minimum
500V
Input connector DB-25 Female D-Sub
Parallel Output connector DB-44 Male D-Sub
SPI Port connector DE-9 Male D-Sub
SPI Data Rate, maximum 1 Mbps
Output source current, mini-
mum, per output
+/- 12ma
Cost
3103 Digital I/O Module $750
About Avermetrics
Founded in 2010, Avermetrics develops, manufactures,
and markets a complete line of Test and Measurement
systems, all with a focus on testing in production envi-
ronments. Speed, accuracy, and data combine to make
your production tests effective as possible.
Our engineering staff is one of the best around, with
decades of experience developing military radar and
simulation systems, RF and microwave products,
pro-audio, MI and consumer mid- and high-volume
products, medical and scientific instrumentation, fac-
tory process control systems, and more. While manag-
ing volume production in the US and Asia, we have
learned best practices for testing and verification on
production lines.
Now we have taken all of that experience and pro-
duced the only Test and Measurement system available
that is tailor made for you and your production test
requirements.