1. Clement Mensah
11222 Braesridge Dr Apt 3149.
Houston TX 77071.
832 815 7446 or 713 474 7407.
Clemsarp2004@yahoo.com
Objective:
To obtain a full-time position in the manufacturing, assembling or production environment where
I can maximize my skills, enhance my work experience and enable me to make a positive
contribution to the company.
Education and Certification:
Sunyani Senior Secondary High, 2001
Work Experience:
Pro Energy-Energy Parts Solutions
Field Service Technician on transformers 10/2015-04/2016
As service Technician I built and repair high voltage transformers in a substation, vacuuming
and circulating of oil from the rig pump to the transformers, repair and replace bushings and
radiators, help in carrying out test or troubleshoot on the transformers after it been repaired and
built. Ability to read and interpret blue print, electrical drawings and schematic drawings, able to
use hands and power tools. Experience with Vacuum Integrity process. Mechanical
competence.
Ability operate forklift
Assemble HV Switchgear, as well positioned, aligned, or adjusted work pieces or electrical parts
to facilitate wiring or assembly. Compiling test reports
• Pulling & Terminating Control Cable.
I have extensive OSHA 10 TRAINING and TWIC CARD. Ability to climb and work on heights,
stooping, bending, lifting and able to stand long period of time or hours to perform a job.
Ability to travel up to 100%.
ARAMARK (Harris County Detention Center) Maintenance Technician 03/2015-
09/2015
As the Maintenance Technician, I was responsible for Maintaining and overseeing the operation
of the building systems, including HVAC, mechanical and electrical equipment, repairing and

2. fixing plumbing issues, taking care of electring problems in the facility, installing or fixing new
light fistures, sprinkler systems replacing and changing sprinkler heads.
Performing plumbing, electrical and HVAC repairs
Performing start up procedures
Directly reporting to Chief Engineer, preforming Physical requirements like stooping, standing,
climbing and frequent lifting minimum of 50 lbs of equipment (pumps, tools, ladders
North American Substation Services
Service Technician 1 on Transformers 10/2014-02/2015
As service Technician I built and repair high voltage transformers in a substation, vacuuming
and circulating of oil from the rig pump to the transformers, repair and replace bushings and
radiators, help in carrying out test or troubleshoot on the transformers after it been repaired and
built. Ability to read and interpret blue print, electrical drawings and schematic drawings, able to
use hands and power tools. Experience with Vacuum Integrity process. Mechanical
competence.
Ability operate forklift
Assemble HV Switchgear, as well positioned, aligned, or adjusted work pieces or electrical parts
to facilitate wiring or assembly. Compiling test reports
• Pulling & Terminating Control Cable.
I have extensive OSHA 10 TRAINING and TWIC CARD. Ability to climb and work on heights,
stooping, bending, lifting and able to stand long period of time or hours to perform a job.
Ability to travel up to 100%.
GE Aero-A Gas Turbine Generator Manufacturing
Instrument Technician (Long TermTemporal)
04/2011 To 09/2014 One Year on Test Line, switched to Working as an Assembly
Technician (wireman).
.

3. • As an Instrument Technician I set up, used pressure pump, hydraulic pump, electric meter to
calibrate switches and check all instruments from pressure, pressure differential & level
transmitters to gas detectors and corresponding transmitter. I am able to use hands and power
tools
• Performed point to point and visual inspections on all wires and instruments installed to assure
proper connections.
•Control & Protection Systems, knows a lot about testing and assembly. I have experience with
Mechanical erection of High Voltage Substations.
Manage assembly and testing crews. Monitored project costs to insure proper cost control?
I have extensive OSHA 10 TRAINING.
•Power distribution or power distribution system.
•Megger
•Electrical equipment. •Electrical testing.
• We also interconnect the unit to our test line load banks to perform a full operational load test
(100 Mega Watt Load) to troubleshoot and correct any program malfunctions on the control
board. Responsible for the layout cable routing and identification of location of electrical
components in gas turbine, high voltage transformers, vacuuming and circulating of oil from the
rig pump to the transformers, repair and replace bushings and radiators, help in carrying out test
or troubleshoot on the transformers after it been repaired and built.
• Knowledge in forklift, Ariel lift, Boom lift. Experience in overhead cranes, hand, power tools
and hydraulic tools. As a wireman I cut, lay and build cable trails, drill, connect and wire
electrical components or instruments in gas turbine by following schematic drawings and
blueprints or electrical prints with the use of electric, power and hand tools, able to read F&IDS,
climbing on heights, bending, pulling of electrical cables. Conform to all safety and quality
requirements and perform housekeeping before and after production.
Toshiba International Corporation (Long term Temporary position)
Assembly Technician
4/2008-2/2011
• Read and interpreted schematic drawings, diagrams, specifications, work orders, or reports to
determine materials requirements or assembly instructions.
• Insert and winding motor coil, connects and soldering of motor cables and also testing of motor
resistance. I am able to use hands and power tools.
• Pulling & Terminating Control Cable

4. • Marked and tagged components so that stock inventory can be tracked and identified.
• Assembled electrical or electronic systems or support structures and install components, units,
subassemblies, wiring, or assembly casings, using rivets, bolts, soldering or micro-welding
equipment.
• Adjusted, repaired, or replaced electrical or electronic component parts to correct defects and
to ensure conformance to specifications. I have experience with Mechanical erection of High
Voltage Substations
• Conferred with supervisors or engineers to plan or review work activities or to resolve
production problems.
• Inspected or tested wiring installations, assemblies, or circuits for resistance factors or for
operation and record results.
• Packed finished assemblies for shipment and transport them to testing department, using
hoists or hand trucks.
• Completed, review, or maintained production, time or component waste reports. I assembled
Feedback Devices
• Measured and adjusted voltages to specified values to determine operational accuracy of
instruments. .
• Drilled or tap holes in specified equipment locations to mount control units or to provide
openings for elements, wiring, or instruments.
• Fabricated or formed parts, coils, or structures according to specifications, using drills,
calipers, cutters, or saws.
• Built and installed all units and servers according to specifications
Alcon Manufacturing 12.50 Temporary
Materials Control Technician
04/2007-2/2008
• Operate hand pallet jack, electric jack, forklift and counter balance and reach truck to transfer
pallets of packaged goods off to the conveyor and transport to the warehouse.
• Performed routine and repetitive assembly-line packaging tasks, standing, bending and
walking for long periods of time.
• Performed a combination of manual and clerical shipping and/or receiving duties which require
the use of computers to maintain data.

5. • Verified quantity, weight, and conformance of materials; prepares records of materials shipped
and bills of loading; routes materials to destinations.
• Assigned to different workstations as production needs require and work overtime when
necessary.
• Replaced, assembled and re-built machines & operate robot machines. I am able to use hands
and power tools in every position held in my career.