Caterpillar Cat CS-533E, CP-533E Vibratory Compactor (Prefix BZE) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
CS-533E and CP-533E
Vibratory Compactor

Shutdown SIS
Previous Screen
Product: VIBRATORY COMPACTOR
Model: CS-533E VIBRATORY COMPACTOR BZE
Configuration: CS-533E,CP-533E Vibratory Compactor BZE00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
CP-533E and CS-533E
Vibratory Soil Compactors
Machine Systems
Media Number -KENR3664-05 Publication Date -01/12/2009 Date Updated -17/12/2009
i01959207
Piston Motor (Drum Propel) - Disassemble
SMCS - 4351-015; 5058-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
B 8H-0663 Bearing Puller Gp 1
Start By:
A. Remove the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Drum
Propel) - Remove".
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
Note: Regular maintenance and frequent inspections are routine precautions. Practice preventive
maintenance before damage occurs. Preventive maintenance can help to avoid a failure. If a failure
occurs, an accurate diagnosis of the cause can prevent a recurrence. Information is available to
analyze the failures of the piston pump and the motor. Refer to Special Publication, SEBD0641,
"Analyzing Axial Piston Pump and Motor Failures".
Note: After disassembly has been completed, check the condition of all the components. Refer to
Guideline For Reusable Parts, SEBF8032, "Piston Pumps and Motors". During reconditioning,
1/13
CS-533E,CP-533E Vibratory Compactor BZE00001-UP (MACHINE) POWERED B...
2021/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

correct any conditions that might have caused the original failure. Information is available to
analyze failures on the piston pumps and the motor. Refer to Special Publication, SEBD0641,
"Analyzing Axial Piston Pump and Motor Failures".
Illustration 1 g01018276
1. Remove bolts (2) and valve (3) from housing (1) .
2. Remove O-ring seal (4) from valve (3) .
2/13
2021/3/13

3. Remove bolts (4) and head (5) .
4. Remove plate (6) and O-ring seal (7) from head (5) .
5. Remove bearing cup (8) .
3/13
2021/3/13

6. Remove plug (9) .
7. Remove O-ring seal (10) from plug (9) .
4/13
2021/3/13

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
10. Remove poppet valve (13) and spring (14) .
5/13
2021/3/13

11. Remove plug (15) and plug (16) .
13. Remove spring (18) .
6/13
2021/3/13

15. Remove spring (20) .
16. Remove spacers (21) and spool (22) .
17. Remove O-ring seal (23) and bearing cone (24) .
7/13
2021/3/13

19. Remove nut (25) from plug (26) .
20. Remove ring (27) and barrel (28) .
8/13
2021/3/13

21. Remove pistons (30) and plate (29) from barrel (28) .
22. Remove plate (29) from pistons (30) .
9/13
2021/3/13

23. Remove retainer (31) .
24. Use Tooling (A) and a suitable press in order to remove retaining ring (32) .
10/13
CS-533E,CP-533E Vibratory Compactor BZE00001-UP (MACHINE) POWERED ...
2021/3/13

25. Remove retaining ring (32), spring (33), washer (34), and pins (35) from barrel (28) .
27. Remove swashplate (37) and pin (38) .
28. Remove the bearings from the swashplate.
11/13
2021/3/13

29. Remove shaft (39) .
30. Remove bearings (40) .
31. Remove bearing cup (40A) .
12/13
2021/3/13

32. Use a suitable press and Tooling (B) in order to remove bearing cone (41) from shaft (39) .
33. Remove retaining ring (42) .
34. Remove seal (43) .
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Mar 13 19:46:49 UTC+0800 2021
13/13
2021/3/13

Shutdown SIS
Previous Screen
CP-533E and CS-533E
Machine Systems
i01959208
Piston Motor (Drum Propel) - Assemble
SMCS - 4351-016; 5058-016
Assembly Procedure
Table 1
Required Tools
A 1P-0510 Driver Gp 1
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning
fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be
deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. Dirt and other contaminants can damage the precision
component. Perform assembly procedures on a clean work surface. Keep components covered and
protected at all times.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
1/13
2021/3/13

1. Install seal (43) .
2. Install retaining ring (42) .
3. Raise the temperature of bearing cone (41) .
4. Install bearing cone (41) onto shaft (39) .
2/13
2021/3/13

5. Install bearings (40) .
6. Install bearing cup (40A) .
7. Install shaft (39) .
8. Install the bearings onto the swashplate.
9. Install swashplate (37) and pin (38) .
3/13
2021/3/13

10. Install plug (36) .
4/13
2021/3/13

Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
11. Use Tooling (A) and a suitable press in order to install retaining ring (32) .
12. Install retaining ring (32), spring (33), washer (34), and pins (35) from barrel (28) .
13. Install retainer (31) .
14. Install plate (29) onto pistons (30) .
5/13
2021/3/13

15. Install pistons (30) and plate (29) into barrel (28) .
16. Install ring (27) and barrel (28) .
17. Install nut (25) into plug (26) .
6/13
2021/3/13

19. Install O-ring seal (23) and bearing cone (24) .
7/13
2021/3/13

20. Install spacers (21) and spool (22) .
21. Install spring (20) .
22. Install O-ring seal (19) into plug (16) .
injury.
8/13
2021/3/13

23. Install spring (18) .
24. Install O-ring seal (17) into plug (15) .
25. Install plug (15) and plug (16) .
26. Install poppet valve (13) and spring (14) .
27. Install O-ring seal (12) onto plug (11) .
9/13
2021/3/13

injury.
29. Install O-ring seal (10) onto plug (9) .
10/13
2021/3/13

31. Install bearing cup (8) .
32. Install plate (6) and O-ring seal (7) into head (5) .
11/13
2021/3/13

33. Install bolts (4) and head (5) .
34. Position O-ring seal (4) onto valve (3) .
12/13
2021/3/13

35. Install bolts (2) and valve (3) onto housing (1) .
End By: Install the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Drum
Propel) - Install".
Sat Mar 13 19:47:46 UTC+0800 2021
13/13
2021/3/13

Shutdown SIS
Previous Screen
CP-533E and CS-533E
Machine Systems
i01947902
Piston Motor (Drum Propel) - Install
SMCS - 4351-012; 5058-012
Installation Procedure
1. Use two persons and install propel motor (5) and two bolts (7). The weight of the propel
motor is approximately 24 kg (53 lb).
2. Install hose assemblies (4) on propel motor (5) .
3. Install hose assemblies (6) and (3) on drum propel motor (5) .
4. Install hose assembly (2) on final drive planetary (1) .
1/2
2021/3/13

5. Fill final drive planetary (1) with oil. The capacity of the final drive planetary is
approximately 3.2 L (0.86 US gal). Refer to Operation and Maintenance Manual for the
correct procedure.
Sat Mar 13 19:48:41 UTC+0800 2021
2/2
2021/3/13

Shutdown SIS
Previous Screen
CP-533E and CS-533E
Machine Systems
i01948078
Final Drive Planetary (Drum Propel) - Remove
SMCS - 5655-011
Removal Procedure
Table 1
Required Tools
A 6V-2082 Lifting Hook 1
B 138-7574 Link Brackets 2
Start By:
A. Remove the drum. Refer to Disassembly and Assembly, "Drum - Remove".
1. Drain the oil from the final drive planetary into a suitable container. The capacity of the
final drive planetary is approximately 3.2 L (0.86 US gal). Refer to Operation and
Maintenance Manual for the correct procedure.
1/3
2021/3/13

2. Attach a suitable lifting device and Tooling (A) to plate (1), as shown.
3. Remove bolts (2) and remove plate (1), the mounting plate, the drum propel motor, and the
final drive planetary as a unit from the mounts. The weight of the plate, the mounting plate,
the propel motor and the final drive planetary is approximately 327 kg (720 lb).
4. Remove bolts (4) from propel motor (3). Use two persons and remove the propel motor. The
weight of the propel motor is approximately 24 kg (53 lb). Remove the O-ring seal from the
propel motor.
5. Attach a suitable lifting device and Tooling (B) to plate (5). Remove bolts (6) and remove
plate (5). The weight of the plate is approximately 50 kg (110 lb).
6. Remove the bolts and remove adapter (7) from the final drive planetary. Remove the O-ring
seal from the adapter.
2/3
2021/3/13

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

7. Attach Tooling (B) to plate (8). Remove bolts (9) and remove plate (8) from final drive
planetary (10). The weight of plate (8) for the CS-533E is approximately 84 kg (185 lb).
The weight of plate (8) for the CP-533E is approximately 94 kg (207 lb).
Sat Mar 13 19:49:37 UTC+0800 2021
3/3
2021/3/13

Caterpillar Cat CS-533E, CP-533E Vibratory Compactor (Prefix BZE) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

More from 8fusejkdmd9i

More from 8fusejkdmd9i (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat CS-533E, CP-533E Vibratory Compactor (Prefix BZE) Service Repair Manual Instant Download.pdf