Select and use hand, power tools and electrical devices relevant to construction electrical works

1. Assistant Electrician
(NSQF Level – 3)
Select and use hand, power
tools and electrical devices
relevant to construction
electrical works
Assistant Electrician (NSQF Level – 3)
SECTOR: CONSTRUCTION
SUB-SECTOR: REAL ESTATE AND
INFRASTRUCTURE
OCCUPATION: CONSTRUCTION AND
ELECTRICAL WORKS
REF. ID: CON/Q0602
NSQF LEVEL: 3
Sl no:2

2. Electrician Hand Tools
It is important that the electrician uses proper tools
for his work. The accuracy of workmanship and
speed of work depend upon the use of correct
tools. If the tools are properly used, and
maintained, the electrician will find the working
efficiency increases and the skills becomes a work
habit. Listed below are the most commonly used
tools by skilled electrician.

3. Line Tester
This helps to
check for the
presence of
the electricity
in the
conductor

4. Screw Driver
It is use for
screw
tighten
and
loosening

5. Philip Screw Driver
It is use for
screw
tighten
and
loosening

6. Combination Plier
It is used
for cutting
wire as well
as holding
objects

7. It is used for
cutting wire
Side cutting Plier

8. Nose Plier
It is used
for holding
deep
objects and
wire
cutting

9. Wire Stripper
It is used
for cutting
wires

10. Automatic Wire Stripper
This helps to
cut the wire
without
damaging the
conductor

11. Electrician Knife
It is used to
remove
wires
insulation

12. Metal files
It is used to
grind and
smooth

13. Claw Hammer
It helps in
hitting the
nails as
well as
plucking
the nails

14. Sledge Hammer
It is used
for beating
and fating
hard
objects

15. Ball Peen Hammer
It is used
for hitting
small nails

16. Cross Peen Hammer
It is used
for bending
metal
sheets as
well as for
nailing

17. Rubber Hammer
It is used
for motor
winding

18. Fiber Hammer
It is used
for motor
winding

19. Hack Saw Blade & Frame
It is use for
cutting PVC
and Metal
pipes

20. Tenon Saw
It is used
for cutting
wooden
box

21. Firmer Chisel
It is used to
make holes
in wood

22. Crimping Tool
A crimping tool is a
device used to
conjoin two pieces
of metal by
deforming one or
both of them in a
way that causes
them to hold each
other. The result of
the tool's work is
called a crimp.

23. Bench Vice
This helps
to stabilize
the
material

24. Pipe Vice
Its use hole PVC or
Metal Pipe
Helps keep
the pipes
firm

25. Cold Flat Chisel
It is used to make slot on wall
It is used to
make tiles
on the
walls

26. Rawl plug tool
It is used to
make holes on
the walls

27. Center Punch Tool
It is used to
make pilot hole
to metal
It is used to
make pilot
holes in
metal

28. Pipe Bending Spring
It is used to
bent PVC
pipe

29. Cable Puller
It is used
to pull the
wire
through
the pipe

30. Angle Grinder
It is used to
cut metal
and PVC
pipes

31. Drilling Machine
It is used to
make hole
on the wall
and
concrete

32. Drilling Machine wireless
It is used to
make hole
on the wall
and
concrete

33. Wall Cutting Machine
It is used to
cut wall
and ceiling

34. Soldering Iron
It is used to
weld two
wires and
components

35. Measuring tape
It is used
to
measure
length
and width

36. Plumb Bob
It is used
for
marking
vertical
lines on
the wall.

37. Standard wire gauge
It is used
to measure
wire gauge

38. Torpedo Level
It is used
to level
switch
board and
pipes.

39. Micro Meter
It is used to
measure
wire gauge

40. Vernier Caliper
It is used
to measure
length of
objects

41. Double ended spanner
It using
tighten and
loosing the
nut and
bolts

42. Ring Spanner
It using
tighten and
loosing the
nut and
bolts

43. Monkey Spanner
It using
tighten and
loosing the
nut and
bolts