Thông số tài liệu kỹ thuật bộ đổi nguồn Mean Well, Catalogue bộ nguồn Mean Well, Power supply Catalogue

7. ½ Features :
60W Single Output LED Power Supply CEN-60 series
CEN-60-54
0 ~ 1.15A
62.1W
59 ~ 65V
40.5 ~ 54V
49 ~ 58V
0.9 ~ 1.15A
¡E
¡E
¡E
¡E
¡E
¡E
¡E
¡E
¡E
¡E
¡E
¡E
Universal AC input / Full range (up to 295VAC)
Protections: Short circuit / / Over voltage / Over temperature
Output voltage and constant current level adjustable
Built-in active PFC function
IP66 design for indoor or outdoor installations
Cooling by free air convection
100% full load burn-in test
High reliability
Suitable for LED lighting and moving sign applications
Compliance to worldwide safety regulations for lighting
Suitable for dry / damp / wet locations
3 years warranty
Over current
¡EClass 2 power unit
¡½ Features :
File Name:CEN-60-SPEC 2012-12-26
SPECIFICATION
MODEL CEN-60-20 CEN-60-24 CEN-60-30 CEN-60-36CEN-60-12 CEN-60-15 CEN-60-48CEN-60-42
DC VOLTAGE
CURRENT RANGE
RATED POWER
OUTPUT
LINE REGULATION
LOAD REGULATION
SETUP TIME
VOLTAGE RANGE Note.4
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER CURRENT
SHORT CIRCUIT
OVER VOLTAGE
OVER TEMPERATURE
20V 24V 30V 36V 54V12V 15V 48V42V
0 ~ 3A 0 ~ 2.5A 0 ~ 2A 0 ~ 1.7A0 ~ 5A 0 ~ 4A 0 ~ 1.3A0 ~ 1.45A
60W 60W 60W 61.2W60W 60W 62.4W60.9W
1.8Vp-p 2.4Vp-p 3Vp-p 3.6Vp-p 5Vp-p2Vp-p 2.4Vp-p 4.6Vp-p4Vp-p
¡Ó10%
¡Ó3.0%
¡Ó5.0%
1400ms / 230VAC 2800ms / 115VAC at full load
90 ~ 295VAC 127 ~ 417VDC
47 ~ 63Hz
PF>0.97/115VAC, PF>0.95/230VAC, PF>0.9/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
88% 89% 90% 90% 91%86% 87% 91%90%
22.8 ~ 26V 28 ~ 34V 34 ~ 38V 41 ~ 46V14.5 ~ 17V 17.5 ~ 21V 54 ~ 60V47 ~ 52V
0.8A/115VAC 0.4A/230VAC 0.3A/277VAC
<0.75mA / 240VAC
95 ~ 110%
Protection type : Constant current limiting, recovers automatically after fault condition is removed
Hiccup mode, recovers automatically after fault condition is removed
-30 ~ +70¢J (Refer to "Derating Curve")
20 ~ 95% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH¢J
¡Ó ¢J ¢J0.03%/ (0 ~ 50 )
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
523.4K hrs min. MIL-HDBK-217F (25 )¢J
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
5. Constant current operation region is within 75% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please
reconfirm special electrical requirements for some specific system design.
6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
7. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
¢J
0.56Kg;24pcs/14.4Kg/1.11CUFT
Protection type : Shut down o/p voltage, re-power on to recover
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
ENVIRONMENT
SAFETY &
EMC
PROTECTION
85 10 (RTH1)¢J¡Ó ¢J
Protection type : Shut down o/p voltage, re-power on to recover
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH¢J
SAFETY STANDARDS
Compliance to EN55015, EN61000-3-2 Class C ( 75% load) ; EN61000-3-3¡Ù
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61547, light industry level (surge 4KV), criteria B
15 ~ 20V 18 ~ 24V 22.5 ~ 30V 27 ~ 36V9 ~ 12V 11.25 ~ 15V 36 ~ 48V31.5 ~ 42V
RATED CURRENT 3A 2.5A 2A 1.7A 1.15A5A 4A 1.3A1.45A
CONSTANTCURRENTOPERATIONVOLTAGE Note.5
17 ~ 22V 22 ~ 27V 27 ~ 33V 33 ~ 40V10.8 ~ 13.5V 13.5 ~ 17V 43 ~ 53V37 ~ 46VVOLTAGE ADJ. RANGE (SVR1)
CURRENT ADJ. RANGE(SVR2) 2.3 ~ 3A 1.9 ~ 2.5A 1.5 ~ 2A 1.3 ~ 1.7A3.75 ~ 5A 3 ~ 4A 1 ~ 1.3A1.1 ~ 1.45A
IP66110
SELV ..
F M M
UL879, UL8750, CSA C22.2 No. 207-M89, CSA C22.2 No. 250.0-08, TUV EN61347-1, EN61347-2-13, IP66, J61347-1, J61347-2-13 approved
185*62.5*40.5mm (L*W*H)
EMC IMMUNITY
EMC EMISSION
COLD START 45A(t =85 s measured at 50% I ) at 230VACwidth peak£g

8. Mechanical Specification
File Name:CEN-60-SPEC 2012-12-26
Case No.993B Unit:mm
Derating Curve Static Characteristics
AMBIENT TEMPERATURE ( )¢J
LOAD(%)
-30 -25 -5 0 15 30 50 60 70
20
40
60
80
100
INPUT VOLTAGE (V) 60Hz
90 100 125 135 145 155 165 175 180 200 230 295
100
90
80
70
60
50
40
LOAD(%)
(HORIZONTAL)
fosc : 50KHz(115VAC)
75KHz(230VAC)
DETECTION
PWM & PFC
CIRCUIT
O.L.P.
EMI FILTER
RECTIFIERS
POWER
SWITCHING
FILTER
&
RECTIFIERS +V
-V
I/P
FG
CONTROL
O.V.P.
&
O.C.P.
81T case
31.25
¡° T case: Max. Case Temperature.
60W Single Output LED Power Supply CEN-60 series
Block Diagram
40.5
300 20¡Ó
SJTW 18AWG 3C¡ÑFG (Green/Yellow)
AC/L(Brown)
AC/N(Blue)
30.6
45
62.5
300 20¡Ó
SVT 18AWG 2C¡Ñ
£r ¡Ñ4.6 4PL
IoVo
ADJ.ADJ.
-V(Black)
+V(Red)
7.6
10.5 164
185

9. 0.64
0.68
0.72
0.76
0.80
0.84
0.88
0.92
0.96
1.00
50% 60% 70% 80% 90% 100%
277Vac
230Vac
115Vac
50
54
58
62
66
70
74
78
82
86
90
94
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
277Vac
230Vac
115Vac
CEN-60 series possess superior working efficiency that up to 91% can be reached in field applications.
EFFICIENCY(%)
LOAD
Power Factor Characteristic
EFFICIENCY vs LOAD (48V Model)
PF
LOAD
DRIVING METHODS OF LED MODULE
(60W)
Constant Current Mode
This LED power supply is suggested to work in constant current mode area (CC) to drive the LEDs.
Typical LED power supply I-V curve
Vo(%)
100
75
50 100
(max.)
Io (%)
Constant
Current area
Hiccup
Protection
60W Single Output LED Power Supply CEN-60 series
File Name:CEN-60-SPEC 2012-12-26

12. 70
72
74
76
78
80
82
84
86
88
90
92
94
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
115VAC
230VAC
277VAC
0. 84
0. 86
0. 88
0. 9
0. 92
0. 94
0. 96
0. 98
1
65% 70% 80% 90% 100%
115VAC
230VAC
277VAC

15. 80
82
84
86
88
90
92
94
96
98
100
60% 70% 80% 90% 100%
277VAC
230VAC
0. 84
0. 86
0. 88
0. 9
0. 92
0. 94
0. 96
0. 98
75% 80% 85% 90% 95% 100%
277VAC
230VAC

18. 0.82
0.84
0.86
0.88
0.9
0.92
0.94
0.96
0.98
1
1.02
50% 60% 70% 80% 90% 100%
110V
230V
277V
0
10
20
30
40
50
60
70
80
90
100
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
110V
230V
277V

22. 0.82
0.84
0.86
0.88
0.9
0.92
0.94
0.96
0.98
1
1.02
50% 60% 70% 80% 90% 100%
110V
230V
277V
0
10
20
30
40
50
60
70
80
90
100
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
110V
230V
277V

23. SPECIFICATION
MDR-40-5 MDR-40-12 MDR-40-24 MDR-40-48MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME Note.5
HOLD UP TIME (Typ.)
VOLTAGE RANGE
FREQUENCY RANGE
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT (Typ.)
SAFETY STANDARDS
WORKING HUMIDITY
WORKING TEMP.
DC OK SIGNAL
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVERLOAD
OVER VOLTAGE
5V 12V 24V 48V
6A 3.33A 1.7A 0.83A
0 ~ 6A 0 ~ 3.33A 0 ~ 1.7A 0 ~ 0.83A
30W 40W 40.8W 39.8W
80mVp-p 120mVp-p 150mVp-p
24 ~ 30V
200mVp-p
48 ~ 56V
¡Ó2.0% ¡Ó1.0% ¡Ó1.0% ¡Ó1.0%
12 ~ 15V5 ~ 6V
¡Ó1.0% ¡Ó1.0% ¡Ó1.0% ¡Ó1.0%
¡Ó1.0% ¡Ó1.0% ¡Ó1.0% ¡Ó1.0%
500ms, 30ms/230VAC 500ms, 30ms/115VAC at full load
50ms/230VAC 20ms/115VAC at full load
85 ~ 264VAC 120 ~ 370VDC
47 ~ 63Hz
78% 86% 88% 88%
1.1A/115VAC 0.7A/230VAC
COLD START 30A/115VAC 60A/230VAC
105 ~ 150% rated output power
Protection type : Constant current limiting, recovers automatically after fault condition is removed
6.25 ~ 7.25V
Protection type : Shut down o/p voltage, re-power on to recover
15.6 ~ 18V 31.2 ~ 36V 57.6 ~ 64.8V
-20 ~ +70¢J (Refer to "Derating Curve")
Relay contact rating(max.): 30V/1A resistive
20 ~ 90% RH non-condensing
-40 ~ +85 , 10 ~ 95% RH¢J
¡Ó ¢J ¢J)0.03%/ (0 ~ 50
Component : each along X, Y, Z axes ; Mounting : Compliance to IEC60068-2-610 ~ 500Hz, 2G 10min./1cycle, period for 60min.
301.7K hrs min. MIL-HDBK-217F (25 )¢J
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
5. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
¢J
File Name:MDR-40-SPEC 2012-12-14
UL508, UL60950-1, pprovedTUV EN60950-1 a
Compliance to EN55011, EN55022 (CISPR22), EN61204-3 ,Class B EN61000-3-2,-3
Compliance to EN61000-4-2, 3, 4, 5, 6, 8, 11, EN55024, EN61000-6-2, EN61204-3, heavy industry level, criteria A
40W Single Output Industrial DIN Rail Power Supply MDR-40 series
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
ENVIRONMENT
PROTECTION
SAFETY &
FUNCTION
EMC
(Note 4)
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
¡E
¡E
¡E
¡E
¡E
¡E
¡E
¡E
¡E
Universal AC input/Full range
Protections: Short circuit / Overload / Over voltage
Cooling by free air convection
Can be installed on DIN rail TS-35/7.5 or 15
LED indicator for power on
DC OK relay contact
No load power consumption<0.75W
100% full load burn-in test
3 years warranty
¡½ Features :
40*90*100mm (W*H*D)
0.3Kg; 42pcs/13.6Kg/0.82CUFT
..
LEAKAGE CURRENT <1mA / 240VAC
I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500VDC / 25 / 70% RH¢J
EMC IMMUNITY
EMC EMISSION

24. Block Diagram
DC OK Relay Contact
Mechanical Specification
File Name:MDR-40-SPEC 2012-12-14
-20 0 10 20 30 45 55 60 70 (VERTICAL)
20
40
60
80
100
AMBIENT TEMPERATURE ( )¢J
LOAD(%)
CIRCUIT
DETECTION
O.L.P.
EMI
FILTER
RECTIFIERS
&
FILTER
POWER
SWITCHING
FILTER
&
RECTIFIERS +V
DC OK
-V
I/P
CONTROL
O.V.P.
O.C.P.
Output Derating VS Input Voltage
INPUT VOLTAGE (VAC) 60Hz
85 10095 120115 160140 200180 240220 264
LOAD(%)
90
100
80
70
60
50
40
Derating Curve
+
Install DIN rail TS35/7.5 or TS35/15
35
+V +V90
40
-V -V
N L
DC OK
+V ADJ
5 5 5 5 5
7.57.5
100
fosc : 60KHz
DC OK
Contact Close PSU turns on / DC OK.
PSU turns off / DC Fail.
30V/1A resistive load.
Contact Open
Contact Ratings (max.)
FG
Case No.962A Unit:mm
40W Single Output Industrial DIN Rail Power Supply MDR-40 series

25. SPECIFICATION
MDR-60-5 MDR-60-12 MDR-60-24 MDR-60-48MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME Note.5
HOLD UP TIME (Typ.)
VOLTAGE RANGE
FREQUENCY RANGE
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT (Typ.)
SAFETY STANDARDS
WORKING HUMIDITY
WORKING TEMP.
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVERLOAD
OVER VOLTAGE
5V 12V 24V 48V
10A 5A 2.5A 1.25A
0 ~ 10A 0 ~ 5A 0 ~ 2.5A 0 ~ 1.25A
50W 60W 60W 60W
80mVp-p 120mVp-p 150mVp-p
24 ~ 30V
200mVp-p
48 ~ 56V
¡Ó2.0% ¡Ó1.0% ¡Ó1.0% ¡Ó1.0%
12 ~ 15V5 ~ 6V
¡Ó1.0% ¡Ó1.0% ¡Ó1.0% ¡Ó1.0%
¡Ó1.5% ¡Ó1.0% ¡Ó1.0% ¡Ó1.0%
500ms, 30ms/230VAC 500ms, 30ms/115VAC at full load
50ms/230VAC 20ms/115VAC at full load
85 ~ 264VAC 120 ~ 370VDC
47 ~ 63Hz
78% 86% 88% 87%
1.8A/115VAC 1A/230VAC
COLD START 30A/115VAC 60A/230VAC
105 ~ 150% rated output power
Protection type : Constant current limiting, recovers automatically after fault condition is removed
6.25 ~ 7.25V
Protection type : Shut down o/p voltage, re-power on to recover
15.6 ~ 18V 31.2 ~ 36V 57.6 ~ 64.8V
-20 ~ +70¢J (Refer to "Derating Curve")
20 ~ 90% RH non-condensing
-40 ~ +85 , 10 ~ 95% RH¢J
¡Ó ¢J ¢J)0.03%/ (0 ~ 50
Component : each along X, Y, Z axes ; Mounting : Compliance to IEC60068-2-610 ~ 500Hz, 2G 10min./1cycle, period for 60min.
299.2K hrs min. MIL-HDBK-217F (25 )¢J
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
5. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
¢J
File Name:MDR-60-SPEC 2012-12-14
UL508, UL60950-1, pprovedTUV EN60950-1 a
60W Single Output Industrial DIN Rail Power Supply MDR-60 series
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
ENVIRONMENT
PROTECTION
SAFETY &
EMC
(Note 4)
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
¡E
¡E
¡E
¡E
¡E
¡E
¡E
¡E
¡E
Universal AC input/Full range
Protections: Short circuit / Overload / Over voltage
Cooling by free air convection
Can be installed on DIN rail TS-35/7.5 or 15
LED indicator for power on
DC OK relay contact
No load power consumption<0.75W
100% full load burn-in test
3 years warranty
¡½ Features :
40*90*100mm (W*H*D)
0.33Kg; 42pcs/14.8Kg/0.82CUFT
..
LEAKAGE CURRENT <1mA / 240VAC
I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500VDC / 25 / 70% RH¢J
FUNCTION DC OK SIGNAL Relay contact rating(max.): 30V/1A resistive
Compliance to EN55011, EN55022 (CISPR22), EN61204-3 ,Class B EN61000-3-2,-3
Compliance to EN61000-4-2, 3, 4, 5, 6, 8, 11, EN55024, EN61000-6-2, EN61204-3, heavy industry level, criteria AEMC IMMUNITY
EMC EMISSION

26. Mechanical Specification
File Name:MDR-60-SPEC 2012-12-14
Block Diagram
DC OK Relay Contact
-20 0 10 20 30 45 55 60 70 (VERTICAL)
20
40
50
60
80
100
AMBIENT TEMPERATURE ( )¢J
LOAD(%)
CIRCUIT
DETECTION
O.L.P.
EMI
FILTER
RECTIFIERS
&
FILTER
POWER
SWITCHING
FILTER
&
RECTIFIERS +V
DC OK
-V
I/P
CONTROL
O.V.P.
O.C.P.
Output Derating VS Input Voltage
INPUT VOLTAGE (VAC) 60Hz
85 10095 120115 160140 200180 240220 264
LOAD(%)
90
100
80
70
60
50
40
Derating Curve
+
Install DIN rail TS35/7.5 or TS35/15
35
+V +V90
40
-V -V
N L
DC OK
+V ADJ
5 5 5 5 5
7.57.5
100
fosc : 60KHz
12V,24V,48V
5V
Case No.962A Unit:mm
DC OK
Contact Close PSU turns on / DC OK.
PSU turns off / DC Fail.
30V/1A resistive load.
Contact Open
Contact Ratings (max.)
FG
60W Single Output Industrial DIN Rail Power Supply MDR-60 series

29. SPECIFICATION
MODEL PCD-16-1400PCD-16-1050PCD-16-700PCD-16-350
RATED CURRENT
CURRENT RANGE
CURRENT ACCURACY
OPERATING VOLTAGE RANGE
RATED POWER
OUTPUT
SETUP TIME
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT(max.)
LEAKAGE CURRENT
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
SHORT CIRCUIT
OVER TEMPERATURE
1400mA1050mA700mA350mA
0 ~ 1400mA0 ~ 1050mA0 ~ 700mA0 ~ 350mA
¡Ó5.0%
16.8W16.8W16.8W16.8W
2Vp-p2.2Vp-p2.7Vp-p4.6Vp-p
1000ms / 230VAC 2000ms / 115VAC at full load
47 ~ 63Hz
PF>0.9/115VAC, PF>0.9/230VAC, PF>0.9/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
80%80.5%81%82%
0.4A/115VAC 0.2A/230VAC 0.15A/277VAC
<0.5mA / 240VAC
Hiccup mode, recovers automatically after fault condition is removed.
-30 ~ +60¢J(Refer to "Derating Curve")
20 ~ 95% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH¢J
¡Ó ¢J ¢J0.03%/ (0 ~ 50 )
10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes
906.5K hrs min. MIL-HDBK-217F (25 )¢J
84*57*29.5mm (L*W*H)
1. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
2. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
0.19Kg; 72pcs/14.7Kg/0.92CUFT
16W Single Output AC Dimmable LED Power Supply
¡E¡E¡E¡E¡E¡E¡E¡E¡E¡E¡E¡E¡E¡E¡E¡E
AC phase-cut dimming
Work with leading edge and trailing edge TRIAC dimmers
115VAC or 230VAC models available
Built-in active PFC function
Constant current design
Protections: Short circuit / Over temperature
Cooling by free air convection
Fully isolated plastic case
IP30 design
Class 2 power unit
100% full load burn-in test
High reliability
3 years warranty
¢ºClass power unit, no FG
Suitable for indoor LED lighting applications
Low cost
¡½ Features :
PCD-16 series
RIPPLE & NOISE (max.) Note.1
ENVIRONMENT
SAFETY &
EMC
PROTECTION 95 10 (RTH1)¢J¡Ó ¢J
Protection type : Shut down o/p voltage, re-power on to recover
SAFETY STANDARDS
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3.75KVAC
I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH¢J
Compliance to (B type only), FCC part 18 non-consumer equipment (AEN55015 EN61000-3-2 Class C ; EN61000-3-3, type only)
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024,EN61547, light industry level, criteria A
SELV
16 ~ 24V24 ~ 48V 8 ~ 12V12 ~ 16V
PCD-16-350 A A : With AC input 90~ 135VAC.
B : With AC input 180~ 295VAC.
File Name:PCD-16-SPEC 2012-12-26
63V 35V 25V 16VNO LOAD OUTPUT (max.)VOLTAGE
( for B type only)( for A type only)( for B type only)( for B type only)
EMC IMMUNITY
EMC EMISSION
( for PCD-16-350 ) ( except PCD-16-350 )
F 110
IP30
UL8750, CSA C22.2 No. 250.0-08(except for PCD-16-350, PCD-25-350, PCD-25-700), ENEC EN613471, EN61347-2-13,
EN62384(for B type only), IP30 approved ; design refer to UL60950-1, TUV EN60950-1, EN61347-1, EN61347-2-13
COLD START 10A(t =90 s measured at 50% I ) at 230VACwidth peak£g

30. Mechanical Specification
File Name:PCD-16-SPEC 2012-12-26
Case No.PCD16A Unit:mm
29.529.5
1.91.9
5757
15.315.3
15.315.3
2-
3.6
£r
2-
3.6
£r
2- 8.9£r
2- 8.9£r
84
84
UL1430 18AWG
UL1430 18AWG
UL1430 18AWG
V+(RED)
V+(RED)
V-(BLACK)
V-(BLACK)
3
3
3
3
75 5¡Ó
75 5¡Ó
150 10¡Ó
150 10¡Ó
7.3
7.3
7.3
7.3
NISPT-1 18AWG
A Type:(PCD-16-_A)
B Type:(PCD-16-_B)
AC/N(WHITE)
AC/N(WHITE)
AC/L(BLACK)
AC/L(BLACK)
10
10
T case
T case
2020
¡°T case: Max. Case Temperature.
¡°T case: Max. Case Temperature.
fosc : 90KHz(115VAC)
120KHz(230VAC)
DETECTION
PWM & PFC
CIRCUIT
O.L.P.
EMI FILTER
RECTIFIERS FILTER
&
RECTIFIERS +V
-V
I/P
CONTROL
&
O.C.P.
POWER
SWITCHING
Block Diagram
16W Single Output AC Dimmable LED Power Supply PCD-16 series

31. 30
34
38
42
46
50
54
58
62
66
70
74
78
82
86
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
277Vac(B Type)
230Vac(B Type)
115Vac(A Type)
0 .7 8
0 .8 0
0 .8 2
0 .8 4
0 .8 6
0 .8 8
0 .9 0
0 .9 2
0 .9 4
0 .9 6
0 .9 8
1 .0 0
5 0 % 6 0 % 7 0 % 8 0 % 9 0 % 1 0 0 %
2 7 7 V ac(B Type)
2 3 0 V ac(B Type)
1 1 5 V ac(A Type)
Static Characteristics
INPUT VOLTAGE (V)
90
180
135
295
Type A (60Hz)
Type B (50Hz)
100
90
80
70
60
50
40
LOAD(%)
Derating Curve
AMBIENT TEMPERATURE ( )¢J
LOAD(%)
-30 -25 -5 0 15 30 40 50 60
20
40
60
80
100
(HORIZONTAL)
50
PCD-16 series possess superior working efficiency that up to 86%
can be reached in field applications.
EFFICIENCY(%)
LOAD
Power Factor Characteristic
EFFICIENCY vs LOAD (PCD-16-350)
Constant Current Mode
PF
LOAD
(16W)
File Name:PCD-16-SPEC 2012-12-26
16W Single Output AC Dimmable LED Power Supply PCD-16 series

32. File Name:PCD-16-SPEC 2012-12-26
16W Single Output AC Dimmable LED Power Supply PCD-16 series
AC Dimming Operation
MW
PCD-16
TRIAC
Based
Dimmer
Under direct driving, the power supply will work in "constant current mode (CC)" and output voltage of the power supply will be clamped by sum of
¡·The following diagram depicts a typical installation utilizing the PCD-16 :
forward voltage (V ) of the LED strip.F
0A
Io
¡·Dimmer Compatibility Chart
Manufacturer
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LEVITON
LEVITON
LEVITON
JUNG
JUNG
BERKER
Bodo Ehmann LICHTREGLER
CLIPSAL
CLIPSAL
Conduction angle: 30 degrees(min.) / 180 degrees(max.)
Dimmer Model
SKYLARK SF-12P-277 (277VAC / 60Hz)
(277VAC / 60Hz)
(120VAC / 60Hz)
(120VAC / 60Hz)
(120VAC / 60Hz)
(120VAC / 60Hz)
(120VAC / 60Hz)
(120VAC / 60Hz)
(230VAC / 50Hz)
(230VAC / 50Hz)
(230-240VAC / 50Hz)
(230VAC / 50Hz)
(220-240VAC / 50Hz)
(220-240VAC / 50Hz)
DVF-103P-277
SKYLARK SF-10P
SKYLARK S-600P
SKYLARK DVF-103P
ILLUMATECH TM Cat.No.IP106
SURESLIDE TM Cat.No.6633-P
SURESLIDE TM Cat. NO.6615-P
Licht-Management 225 TDE
Licht-Management 225 NV DE
Tronic-Drehdimmer 286710
T39.01
32E450UDM
NO 32E450TM

33. SPECIFICATION
MODEL PCD-25-1400PCD-25-1050PCD-25-700PCD-25-350
RATED CURRENT
CURRENT RANGE
OPERATING VOLTAGE RANGE
RATED POWER
OUTPUT
SETUP TIME
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT(max.)
LEAKAGE CURRENT
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
SHORT CIRCUIT
OVER TEMPERATURE
1400mA1050mA700mA350mA
0 ~ 1400mA0 ~ 1050mA0 ~ 700mA0 ~ 350mA
25.2W25.2W25.2W20.3W
2Vp-p2.2Vp-p2.7Vp-p4.6Vp-p
63V 50V 35V 25V
1000ms / 230VAC 2000ms / 115VAC at full load
47 ~ 63Hz
PF>0.9/115VAC, PF>0.9/230VAC, PF>0.9/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
80%80.5%81%82%
0.6A/115VAC 0.3A/230VAC 0.2A/277VAC
<0.5mA / 240VAC
Hiccup mode, recovers automatically after fault condition is removed.
-30 ~ +60¢J(Refer to "Derating Curve")
20 ~ 95% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH¢J
¡Ó ¢J ¢J0.03%/ (0 ~ 50 )
10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes
906.5K hrs min. MIL-HDBK-217F (25 )¢J
84*57*29.5mm (L*W*H)
0.19Kg; 72pcs/14.7Kg/0.92CUFT
25W Single Output AC Dimmable LED Power Supply
¡½ Features :
PCD-25 series
RIPPLE & NOISE (max.) Note.1
ENVIRONMENT
SAFETY &
EMC
PROTECTION 95 10 (RTH1)¢J¡Ó ¢J
Protection type : Shut down o/p voltage, re-power on to recover
SAFETY STANDARDS
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3.75KVAC
I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH¢J
24 ~ 36V40 ~ 58V 12 ~ 18V16 ~ 24V
PCD-25-350 A A : With AC input 90~ 135VAC.
B : With AC input 180~ 295VAC.
File Name:PCD-25-SPEC 2012-12-26
1. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
2. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
UL8750, CSA C22.2 No. 250.0-08(except for PCD-16-350, PCD-25-350, PCD-25-700), ENEC EN613471, EN61347-2-13,
EN62384(for B type only), IP30 approved ; design refer to UL60950-1, TUV EN60950-1, EN61347-1, EN61347-2-13
AC phase-cut dimming
Work with leading edge and trailing edge TRIAC dimmers
115VAC or 230VAC models available
Built-in active PFC function
Constant current design
Protections: Short circuit / Over temperature
Cooling by free air convection
Fully isolated plastic case
IP30 design
Class 2 power unit
100% full load burn-in test
High reliability
3 years warranty
¡E¡E¡E¡E¡E¡E¡E¡E¡E¡E¡E¡E¡E¡E¡E¡E
¢ºClass power unit, no FG
Suitable for indoor LED lighting applications
Low cost
NO LOAD OUTPUT (max.)VOLTAGE
¡Ó5.0%
Compliance to (B type only),EN55015 EN61000-3-2 Class C ; EN61000-3-3, FCC part 18 non-consumer equipment (A type only)
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024,EN61547, light industry level, criteria AEMC IMMUNITY
EMC EMISSION
CURRENT ACCURACY
( for B type only)( for A type only) ( for PCD-25-350/700 ) ( except PCD-25-350/700 )SELV( for B type only)( for B type only)
F 110
IP30
COLD START 10A(t =20 s measured at 50% I ) at 230VACwidth peak£g

34. File Name:PCD-25-SPEC 2012-12-26
Mechanical Specification Case No.PCD16A Unit:mm
29.529.5
1.91.9
5757
15.315.3
15.315.3
2-
3.6
£r
2-
3.6
£r
2- 8.9£r
2- 8.9£r
84
84
UL1430 18AWG
UL1430 18AWG
UL1430 18AWG
V+(RED)
V+(RED)
V-(BLACK)
V-(BLACK)
3
3
3
3
75 5¡Ó
75 5¡Ó
150 10¡Ó
150 10¡Ó
7.3
7.3
7.3
7.3
NISPT-1 18AWG
A Type:(PCD-25-_A)
B Type:(PCD-25-_B)
AC/N(WHITE)
AC/L(BLACK)
34.5
34.5
T case
T case
14.514.5
¡°T case: Max. Case Temperature.
¡°T case: Max. Case Temperature.
fosc : 90KHz(115VAC)
120KHz(230VAC)
DETECTION
PWM & PFC
CIRCUIT
O.L.P.
EMI FILTER
RECTIFIERS FILTER
&
RECTIFIERS +V
-V
I/P
CONTROL
&
O.C.P.
POWER
SWITCHING
Block Diagram
AC/N(WHITE)
AC/L(BLACK)
25W Single Output AC Dimmable LED Power Supply PCD-25 series

35. 36
40
44
48
52
56
60
64
68
72
76
80
84
88
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
277Vac(B Type)
230Vac(B Type)
115Vac(A Type)
0.78
0.80
0.82
0.84
0.86
0.88
0.90
0.92
0.94
0.96
0.98
1.00
50% 60% 70% 80% 90% 100%
277Vac(B Type)
230Vac(B Type)
115Vac(A Type)
Static Characteristics
INPUT VOLTAGE (V)
90
180
135
295
Type A (60Hz)
Type B (50Hz)
100
90
80
70
60
50
40
LOAD(%)
Derating Curve
AMBIENT TEMPERATURE ( )¢J
LOAD(%)
-30 -25 -5 0 15 30 40 50 60
20
40
60
80
100
(HORIZONTAL)
PCD-25 series possess superior working efficiency that up to 86%
can be reached in field applications.
EFFICIENCY(%)
Power Factor Characteristic
EFFICIENCY vs LOAD (PCD-25-350)
Constant Current Mode
PF
(25W)
File Name:PCD-25-SPEC 2012-12-26
25W Single Output AC Dimmable LED Power Supply PCD-25 series
LOAD
LOAD

36. AC Dimming Operation
MW
PCD-25
TRIAC
Based
Dimmer
Under direct driving, the power supply will work in "constant current mode (CC)" and output voltage of the power supply will be clamped by sum of
¡·The following diagram depicts a typical installation utilizing the PCD-25 :
forward voltage (V ) of the LED strip.F
0A
Io
¡·Dimmer Compatibility Chart
Manufacturer
LUTRON
LUTRON
LUTRON
LUTRON
LUTRON
LEVITON
LEVITON
LEVITON
JUNG
JUNG
BERKER
Bodo Ehmann LICHTREGLER
CLIPSAL
CLIPSAL
Conduction angle: 30 degrees(min.) / 180 degrees(max.)
Dimmer Model
SKYLARK SF-12P-277 (277VAC / 60Hz)
(277VAC / 60Hz)
(120VAC / 60Hz)
(120VAC / 60Hz)
(120VAC / 60Hz)
(120VAC / 60Hz)
(120VAC / 60Hz)
(120VAC / 60Hz)
(230VAC / 50Hz)
(230VAC / 50Hz)
(230-240VAC / 50Hz)
(230VAC / 50Hz)
(220-240VAC / 50Hz)
(220-240VAC / 50Hz)
DVF-103P-277
SKYLARK SF-10P
SKYLARK S-600P
SKYLARK DVF-103P
ILLUMATECH TM Cat.No.IP106
SURESLIDE TM Cat.No.6633-P
SURESLIDE TM Cat. NO.6615-P
Licht-Management 225 TDE
Licht-Management 225 NV DE
Tronic-Drehdimmer 286710
T39.01
32E450UDM
NO 32E450TM
File Name:PCD-25-SPEC 2012-12-26
25W Single Output AC Dimmable LED Power Supply PCD-25 series

39. 30
34
38
42
46
50
54
58
62
66
70
74
78
82
86
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
277Vac(BType)
230Vac(BType)
115Vac(A Type)
0 . 7 8
0 . 8 0
0 . 8 2
0 . 8 4
0 . 8 6
0 . 8 8
0 . 9 0
0 . 9 2
0 . 9 4
0 . 9 6
0 . 9 8
1 . 0 0
5 0 % 6 0 % 7 0 % 8 0 % 9 0 % 1 0 0 %
2 7 7 V a c (B T y p e)
2 3 0 V a c (B T y p e)
1 1 5 V a c (A T y p e)

40. SPECIFICATION
S-250-5 S-250-12 S-250-15 S-250-24 S-250-27MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD TIME (Typ.)
VOLTAGE RANGE
FREQUENCY RANGE
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
SAFETY STANDARDS
SAFETY WITHSTAND VOLTAGE
ISOLATION RESISTANCE
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER LOAD
OVER VOLTAGE
5V
40A
0 ~ 40A
200W
80mVp-p
4.75 ~5.5V
2.0%
0.5%
1.0%
800ms, 50ms at full load
19ms at full load
47 ~ 63Hz
74%
4.8A/115VAC 2.8A/230VAC
COLD START 45A/230VAC
<2mA / 240VAC
105 ~ 135% rated output power
5.75 ~ 6.75V 13.8 ~ 16.2V 17.25 ~ 20.25V 27.6 ~ 32.4V 31.05 ~ 36.45V 55.2 ~ 64.8V
Protection type : Hiccup mode, recovers automatically after fault condition is removed
Protection type : Hiccup mode, recovers automatically after fault condition is removed
UL60950-1 approved
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH
-10 ~ +60 (Refer to "Derating Curve")
20 ~ 90% RH non-condensing
-20 ~ +85 , 10 ~ 95% RH
0.03%/ (0 ~ 50 )
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
238.9K hrs min. MIL-HDBK-217F (25 )
150*140*86mm (L*W*H)
1.15Kg; 8pcs/10.2Kg/0.97CUFT
79% 80% 81.5% 82% 82%
0.5% 0.5% 0.5% 0.5% 0.5%
0.5% 0.5% 0.5% 0.5% 0.5%
1.0% 1.0% 1.0% 1.0% 1.0%
120mVp-p
10.8 ~13.2V
120mVp-p
13.5 ~ 16.5V
120mVp-p
21.6 ~ 26.4V
150mVp-p
24.3 ~ 29.7V
200mVp-p
43.2 ~ 52.8V
12V
18A
0 ~ 18A
216W
15V
15A
0 ~ 15A
225W
24V
10A
0 ~ 10A
240W
27V
9A
0 ~ 9A
243W
48V
5.2A
0 ~ 5.2A
249.6W
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
File Name:S-250-SPEC 2011-08-23
S-250-48
90 ~ 132VAC / 176 ~ 264VAC Selected by switch 248~370VDC
AC input range selected by switch
Protections: Short circuit / Overload / Over voltage
Forced air cooling by built-in DC fan
100% full load burn-in test
Fixed switching frequency at 60KHz
Low cost
High reliability
2 years warranty
Features :
S-250 series
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
ENVIRONMENT
PROTECTION
250W Single Output Switching Power Supply

41. Mechanical Specification
Derating Curve Static Characteristics
File Name:S-250-SPEC 2011-08-23
Case No. 907C Unit:mm
AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (V) 60Hz
90
176
95
180
100 105
185
110
195
115
205
120
215
125
230
130
245 260
132
264
100
90
80
70
60
50
LOAD(%)
-10 0 10 20 30 40 50 60 (HORIZONTAL)
20
40
60
80
100
LOAD(%)
250W Single Output Switching Power Supply S-250 series
Block Diagram fosc : 60KHz
CIRCUIT
DETECTION
O.L.P.
EMI
FILTER
RECTIFIERS
&
FILTER
POWER
SWITCHING
FILTER
&
RECTIFIERS +V
-V
I/P
FG
PWM
CONTROL
O.V.P.
230
115
Air flowdirection
4-
2.6
3-
2.6
6
29.5 27.5
84
15
9
25
140
150
138
12 max.
6
664
124
84
2-
4
8
20
125.5
110
96
10.5
7
14 4
6
89.5
1
2
3
4
5
6
7
8
9
+V ADJ
LED
5-
2.6
2-
2.6
25
86
8
84
33
150
60.59
84
125
28
Terminal Pin No. Assignment
Pin No. Pin No.
1 4,5,6
7,8,92
3
Assignment Assignment
FG
AC/L
AC/N
DC OUTPUT -V
DC OUTPUT +V

42. SE-200-5 SE-200-7.5 SE-200-12SE-200-3.3 SE-200-15 SE-200-24 SE-200-27 SE-200-48
HOLD UP TIME
1000ms, 50ms/230VAC 1000ms,50ms/115VAC at full load
20ms/230VAC 16ms/115VAC at full load
SPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
VOLTAGE RANGE Note.4
FREQUENCY RANGE
EFFICIENCY (Typ.)
INPUT
INRUSH CURRENT (max.)
LEAKAGE CURRENT
SAFETY WITHSTAND VOLTAGE
ISOLATION RESISTANCE
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER LOAD
OVER VOLTAGE
OVER TEMPERATURE
AC CURRENT
90 ~ 132VAC / 180 ~ 264VAC by switch 254 ~ 370VDC
47 ~ 63Hz
79% 82% 85%75% 85% 87% 88% 89%
4.5A/115VAC 2.5A/230VAC
40A/115VAC 55A/230VAC
<3.5mA / 240VAC
105 ~ 150% rated output power
5.75 ~ 7.0V 9.4 ~ 10.9V 13.8 ~ 16.2V3.8 ~ 4.9V 18 ~ 21V 27.6 ~ 32.4V 33.7 ~ 39.2V 57.6 ~ 67.2V
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC / 25 / 70% RH
-20 ~ +50 (Refer to output load derating curve)
20 ~ 90% RH non-condensing
-20 ~ +85 , 10 ~ 95% RH
0.03%/ (0 ~ 50
10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes
215*115*50mm (L*W*H)
0.93Kg; 12pcs/12Kg/0.92CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Please connect positive pole of input voltage with mark “N” of terminal block, connect negative pole of input voltage
with mark “L” of terminal block, using DC voltage for input voltage.
5V 7.5V 12V3.3V 15V 24V 27V 48V
40A 27A 17A40A 14A 8.8A 7.8A 4.4A
0 ~ 40A 0 ~ 27A 0 ~ 17A0 ~ 40A 0 ~ 14A 0 ~ 8.8A 0 ~ 7.8A 0 ~ 4.4A
200W 202.5W 204W132W 210W 211.2W 210.6W 211.2W
150mVp-p 150mVp-p 150mVp-p150mVp-p 150mVp-p 150mVp-p 200mVp-p 240mVp-p
4.5 ~ 5.6V 6 ~ 9V 10 ~ 13.5V2.97 ~ 3.7V 13.5 ~ 18V 20 ~ 26.4V 26 ~ 32V 41 ~ 56V
2.0% 2.0% 1.0%2.0% 1.0% 1.0% 1.0% 1.0%
0.5% 0.5% 0.5%0.5% 0.5% 0.5% 0.5% 0.5%
1.0% 1.0% 0.5%1.5% 0.5% 0.5% 0.5% 0.5%
SAFETY STANDARDS UL60950-1 approved
271.9K hrs min. MIL-HDBK-217F (25 )
200W Single Output Switching Power Supply SE-200 series
Features :
ENVIRONMENT
PROTECTION
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
Protection type : Constant current limiting, recovers automatically after fault condition is removed
File Name:SE-200-SPEC 2012-02-28
SE-200-36
89%
36V
5.9A
0 ~ 5.9A
212.4W
240mVp-p
32 ~ 40V
1.0%
0.5%
0.5%
41.4 ~ 46.8V
AC input range selectable by switch
Protections: Short circuit / Overload / Over voltage/
Over temperature
Cooling by free air convection
Withstand 300vac surge input for 5 second
Built-in constant current limiting circuit
100% full load burn-in test
LED indicator for power on
Fixed switching frequency at 90KHz
Low cost,high reliability
2 years warranty
95 5 (3.3V);100 5 (5V); 90 5 (7.5V);85 5 (12~24V);80 5 (27~36V);75 5 (48V) (TSW1) Detect on case
Protection type : Shut down O/P voltage, recovers automatically after temperature goes down
Protection type :Shut down O/P voltage, re-power on to recover

43. 15 ~ 48V
3.3 ~ 12V
Mechanical Specification
Derating Curve Static Characteristics
Case No. 912E Unit:mm
Terminal pin number assignment :
Pin No. Pin No.
1 4~6
3
2 7~9
Assignment Assignment
AC/L DC OUTPUT -V
FG
AC/N DC OUTPUT +V
117.5
135
215
32.5
32.5
27.5
8
2
8
1
9.5
5
3
4
6
7
+V ADJ.
9
LED
9
50
5
115
50
25
6-M4 L=6mm
150
C
L
50.5
10
5-M3 L=3mm
32.5
15
16
4-M4 L=5mm
177.5
150
200W Single Output Switching Power Supply SE-200 series
File Name:SE-200-SPEC 2012-02-28
12 max.
fosc : 90KHzBlock Diagram
PWM
CIRCUIT
DETECTION
O.L.P.
EMI
FILTER
RECTIFIERSACTIVE
INRUSH
CURRENT
LIMITING
230
115
&
FILTER
POWER
SWITCHING
FILTER
&
RECTIFIERS +V
-V
I/P
CONTROL O.V.P.
O.T.P.
FG
AMBIENT TEMPERATURE ( )
LOAD(%)
20
40
50
60
75
80
100
-20 0 10 20 30 40 50 60 (HORIZONTAL)
LOAD(%)
90
100
80
70
60
50
40
90
180
100
190
132
264
3.3~5V
7.5~48V