cnc router machine using the operating. Jinan Blue Elephant CNC Machinery, professional cnc router and laser machine manufacturer. Welcome to contact us, we provide best price and service.

1. Web:www.elephant-cnc.com Email: manager@elephant-cnc.com Whatsapp/mobile : 0086-15064026772
How to operate Blue Elephant CNC Machinery
Step 1. Connect main power supplier with control cabinet
1.1 Wire show with mark NO. - Yellow color is for groud
1.2 Let main power in OFF and through the inlet pipe,connect power with cabinet inside connector
1.3 This is 380V 3-ph working, L1, L2, L3 don’t need to be Sequence
1.4 Connect with customer factory’s Distribution box,Yellow wire must connect with factory’s Distribution box ground wire
Step 2. Connect compress air tabe and connect water--civculation pamp with vacuwm worktable
2.1 Connect air tube with machine pneumatic FRL
2.2 Adust pressure,pull is open,press is closed, right pressure is 0.6Mpa-0.7Mpa, can not lower 0.6 Mpa
2.3 Connect Water-circulation pump with power supplier
2.4 This is 380V 3-ph working,connect the end with U1V1W1
2.5 This p;ace don’t need connect with ground wire
2.6 Note tighten the screws
2.7 Connect vacuum pump with vacuum valve
2.8 Adjust the hoop position,tighten the nut
2.9 Run pump and let rtation direction the same with arrow sign
2.10 Inject water to water pump
2.11 Best water injection is the distance between thumb and middle finger
2.12 Open the inlet valve,using a vacuum pump after 5 minutes
Step 3: Install double bag dust collector
3.1 Fix vacuum pipe,when use one outlet,please cover others
3.2 Install vacuum pipe bracket
3.3 Install vacuum pipe with machine head
3.4 Fix vacuum pipe with bracket
Step 4: Push button to start use the machine,turn on the power
4.1 Open all emergency stp switch by turn right
4.2 Loading system process
4.3 Machine X,Y,Z axis reset display and Press the power button homing key
4.4 Follows press Z+, X-, Y- Key and adjust machine speed under 30
4.5 When X Y Z appears black and white circles,it means back to zero success
Step 5: Hand wheel control machine X-axis moving display
5.1 From left to right is Axis selector button and Speed selection button
5.2 Rotate speed to maximum speed and then press the speed
5.3 Press the green button in hand wheel side
5.4 Hand wheel’s cckwise rotation is the X-axis positive direction,and vice versa
Step 6: Hand wheel control machine Y-axis moving display
6.1 Press the green button is hand wheel side
6.2 Hand wheel’s clockwise rotation is the Y-axis positive detection,and vice versa
Step 7: Hand wheel control machine Z-axis moving display

2. Web:www.elephant-cnc.com Email: manager@elephant-cnc.com Whatsapp/mobile : 0086-15064026772
Step 8: JOG model,machine manual mode display
8.1 Press the button is machine control panel to move the respective axis moving
8.2 X-axis negative direction display
8.3 Z-axis down direction moving
8.4 Y-axis negative direction moving
8.5 Y-axis positive directon moving
8.6 Manual control position air-cylinder
8.6 Press K9 mist cooling key, position air-cylinder up and down
8.7 Manual control optoelectronic protective wall
8.8 Manual install shank
8.9 Manual unloading knife,first gripping the handle to prevent tools drop,then press the tool key on spinde,remove the
handle
Step 9: MDA model,automatic tool clamping by change T3 to T1
9.1 Press MDA key
9.2 Press foward delete key
9.3 Input T1 key
9.4 Now spindle is with tool and panel show T3,we need make sure T3 tool position was empty
9.5 Press reset key, let the cursor back to the beginning of the program and the machine reset
9.6 In MDA model,press Cycle start Key
9.7 Adjust the speed,advice new user control speed under 30
Step 10: T1-T3 tools change and tool sensor display
10.1 Gantry moving to tools magazine
10.2 Change T3 tool to T1 tool
10.3 In MDA model,make tool sensor automatic
10.4 Press input equal to computer Enter key
10.5 Machine reset and program reset
10.6 Press CHIP REV to finish tool sensor automatic
10.7 Press CYCLE START,advice speed under 30
Step 11 How to make tool sensor aromatic display
11.1 Make tools sensor automatic from T1 to T3 display
11.2 Close tool sensor key in panel
Step 12 How to use U-disk and copy document display
12.1 Press program manager
12.2 Choose USB
12.3 Press direction key to choose copy document
12.4 Press copy key
12.5 Press internal memory
12.6 Press paste files
12.7 Finished and unplug the USB
Step 13 Vacuum work table display

3. Web:www.elephant-cnc.com Email: manager@elephant-cnc.com Whatsapp/mobile : 0086-15064026772
13.1 Take vacuum worktable adsorption cover away
13.2 Open vacuum valves
Step 14 Machine operation process display
14.1 Press machine key in panel
14.2 Press the key “meas work” then the second key
14.3 Not choose G500 but choose G54
14.4 Press this ke to convert axis coordinate system
Step 15 Change to use hand wheel display
15.1 Adjust machine work speed
15.2 Adjust machine spindle to zero point
15.3 Choose lower speed when the distance between spindle and worktable is nearest
Step 16 X,Y,Z Axis choose “set wo” to set process Zero Point
16.1 Press program manage then choose “NC” program
16.2 Choose EXECUTE to load program
16.3 Press “Cycle start”key
16.4 Set process speed,advice new user not set fast speed
16.5 Machine working display
16.6 Close control cabinet power and finish machine display