This document discusses case studies of microturbine combined heat and power (CHP) systems providing cost savings and increased security. It provides three examples: 1) A Radisson hotel in California with two microturbine CHP units providing electricity and hot water, saving $66,336/year. 2) An Inns of America hotel in California with a microturbine CHP unit, saving 40% on energy costs and providing power during a wildfire outage. 3) A restaurant in Italy with a microturbine CHP unit that provided power during a multi-hour blackout. In all cases, the microturbine CHP systems provided both economic and security benefits.
Simulation of a small scale cogeneration system using a microturbinePietro Galli
The aim of the thesis was to develop an operating model of some sizes of Microturbines on the software eQuest.
Then used the model developed to simulate the installation of a Cogeneration (CHP) plant to satisfy the heat and electric demand of a school. The final step was to consider the economics of the investment and choosing which size and use of the turbine was the most convenient for the building.
The key topics of the project were the following:
• Collecting experimental data about some size of Microturbines
• Development of the turbine model for the software eQuest
• Development of the building following the ASHRAE standard
• Simulation of some size of Cogeneration Plants
• Analysis of the results of the simulations
• Energy auditing of the building and analysis of the cost of the current and new plant
• Choice of the best solution for the building
The thesis was developed in collaboration between Politecnico di Torino and the University of Illinois at Chicago, during the course of the double degree program TOP-UIC
Simulation of a small scale cogeneration system using a microturbinePietro Galli
The aim of the thesis was to develop an operating model of some sizes of Microturbines on the software eQuest.
Then used the model developed to simulate the installation of a Cogeneration (CHP) plant to satisfy the heat and electric demand of a school. The final step was to consider the economics of the investment and choosing which size and use of the turbine was the most convenient for the building.
The key topics of the project were the following:
• Collecting experimental data about some size of Microturbines
• Development of the turbine model for the software eQuest
• Development of the building following the ASHRAE standard
• Simulation of some size of Cogeneration Plants
• Analysis of the results of the simulations
• Energy auditing of the building and analysis of the cost of the current and new plant
• Choice of the best solution for the building
The thesis was developed in collaboration between Politecnico di Torino and the University of Illinois at Chicago, during the course of the double degree program TOP-UIC
Microturbines are a green new way to power buildings while heating and cooling them. Also, microturbines burn waste gas from landfills, sewage treatment plants, farms and the like, turning it into clean electricity for the electric grid.
Microturbines are a green new way to power buildings while heating and cooling them. Also, microturbines burn waste gas from landfills, sewage treatment plants, farms and the like, turning it into clean electricity for the electric grid.
Design of Heat Exchanger Network for VCM Distillation Unit Using Pinch Techno...IJERA Editor
In process industries, heat exchanger networks represent an important part of the plant structure. The purpose of the networks is to maximize heat recovery, thereby lowering the overall plant costs. In process industries, during operation of any heat exchanger network (HEN), the major aim is to focus on the best performance of the network As in present condition of fuel crises is one of the major problem faced by many country & industrial utility is majorly depend on this. There is technique called process integration which is used for integrate heat within loop so optimize the given process and minimize the heating load and cooling load .In the present study of heat integration on VCM (vinyl chloride monomer) distillation unit, Heat exchanger network (HEN) is designed by using Aspen energy analyzer V8.0 software. This software implements a methodology for HEN synthesis with the use of pinch technology. Several heat integration networks are designed with different ΔT min and total annualized cost compared to obtain the optimal design. The network with a ΔT min of 90C is the most optimal where the largest energy savings are obtained with the appropriate use of utilities (Save 15.3764% for hot utilities and 47.52% for cold utilities compared with the current plant configuration). Percentage reduction in total operating cost is 18.333%. From calculation Payback Period for new design is 3.15 year. This save could be done through a plant revamp, with the addition of two heat exchangers. This improvement are done in the process associated with this technique are not due to the use of advance unit operation, but to the generation of heat integration scheme. The Pinch Design Method can be employed to give good designs in rapid time and with minimum data.
To Improve Thermal Efficiency of 27mw Coal Fired Power PlantIJMER
Booming demand for electricity, especially in the developing countries, has raised power generation technologies in the headlines. At the same time the discussion about causes of global warming has focused on emissions originating from power generation and on CO2 reduction technologies such as:
(1) Alternative primary energy sources,
(2) Capture and storage of CO2,
(3) Increasing the efficiency of converting primary energy content into electricity.
In the dissertation, the thermal efficiency of the power plant is improved when Control of furnace draft (nearer to balanced draft). Oxygen level decreases percentage of flue gases. Above this level heat losses are increases & below this carbon mono-oxide is formed. Steam power plant is using fuel to generate electrical power. The used of the fuel must be efficient so the boiler can generate for the maximum electrical power. By the time the steam cycle in the boiler, it also had heat losses through some parts and it effect on the efficiency of the boiler. This project will analyze about the parts of losses and boiler efficiency. to find excess air which effect heat losses in boiler. By using the 27 MW coal fired thermal power plant of Birla Corporation Limited, Satna (M.P.) the data is collect by using types of Combustion & heat flow in boiler. Result of the analysis show that the efficiency of boiler depends on mass of coal burnt & type of combustion .This study is fulfilling the objective of analysis to find the boiler efficiency and heat losses in boiler for 27 MW thermal power plant of Birla Corporation Limited, Satna (M.P.)
Electric motors
Editorial - Policy solutions - Facts - Interview - Success stories - Improving market surveillance - Extended product approach - Motor maintenance and refurbishment - Accelerated replacement of less efficient motor stock - Developing powertrains for electric mobility free of critical raw materials - World landscape
The goal of DecarbEurope is to engage decision-makers in policy and industry with solutions that can, in a cost-effective manner, decarbonise Europe at the scale and speed that is needed to achieve our climate goals.
As an ecosystem of twenty sectors — and growing — the initiative connects technologies, policies, and markets. Partners of DecarbEurope commit themselves to common values of deep decarbonisation, cost-effectiveness, circularity, sector-coupling and consumer engagement.
Electric motors play a major role in all economic sectors (industrial, tertiary, residential, agricultural and in transportation), to deliver in a reliable and efficient way mechanical power to a huge variety of processes and services
Smart TV Buyer Insights Survey 2024 by 91mobiles.pdf91mobiles
91mobiles recently conducted a Smart TV Buyer Insights Survey in which we asked over 3,000 respondents about the TV they own, aspects they look at on a new TV, and their TV buying preferences.
LF Energy Webinar: Electrical Grid Modelling and Simulation Through PowSyBl -...DanBrown980551
Do you want to learn how to model and simulate an electrical network from scratch in under an hour?
Then welcome to this PowSyBl workshop, hosted by Rte, the French Transmission System Operator (TSO)!
During the webinar, you will discover the PowSyBl ecosystem as well as handle and study an electrical network through an interactive Python notebook.
PowSyBl is an open source project hosted by LF Energy, which offers a comprehensive set of features for electrical grid modelling and simulation. Among other advanced features, PowSyBl provides:
- A fully editable and extendable library for grid component modelling;
- Visualization tools to display your network;
- Grid simulation tools, such as power flows, security analyses (with or without remedial actions) and sensitivity analyses;
The framework is mostly written in Java, with a Python binding so that Python developers can access PowSyBl functionalities as well.
What you will learn during the webinar:
- For beginners: discover PowSyBl's functionalities through a quick general presentation and the notebook, without needing any expert coding skills;
- For advanced developers: master the skills to efficiently apply PowSyBl functionalities to your real-world scenarios.
DevOps and Testing slides at DASA ConnectKari Kakkonen
My and Rik Marselis slides at 30.5.2024 DASA Connect conference. We discuss about what is testing, then what is agile testing and finally what is Testing in DevOps. Finally we had lovely workshop with the participants trying to find out different ways to think about quality and testing in different parts of the DevOps infinity loop.
PHP Frameworks: I want to break free (IPC Berlin 2024)Ralf Eggert
In this presentation, we examine the challenges and limitations of relying too heavily on PHP frameworks in web development. We discuss the history of PHP and its frameworks to understand how this dependence has evolved. The focus will be on providing concrete tips and strategies to reduce reliance on these frameworks, based on real-world examples and practical considerations. The goal is to equip developers with the skills and knowledge to create more flexible and future-proof web applications. We'll explore the importance of maintaining autonomy in a rapidly changing tech landscape and how to make informed decisions in PHP development.
This talk is aimed at encouraging a more independent approach to using PHP frameworks, moving towards a more flexible and future-proof approach to PHP development.
GraphRAG is All You need? LLM & Knowledge GraphGuy Korland
Guy Korland, CEO and Co-founder of FalkorDB, will review two articles on the integration of language models with knowledge graphs.
1. Unifying Large Language Models and Knowledge Graphs: A Roadmap.
https://arxiv.org/abs/2306.08302
2. Microsoft Research's GraphRAG paper and a review paper on various uses of knowledge graphs:
https://www.microsoft.com/en-us/research/blog/graphrag-unlocking-llm-discovery-on-narrative-private-data/
UiPath Test Automation using UiPath Test Suite series, part 3DianaGray10
Welcome to UiPath Test Automation using UiPath Test Suite series part 3. In this session, we will cover desktop automation along with UI automation.
Topics covered:
UI automation Introduction,
UI automation Sample
Desktop automation flow
Pradeep Chinnala, Senior Consultant Automation Developer @WonderBotz and UiPath MVP
Deepak Rai, Automation Practice Lead, Boundaryless Group and UiPath MVP
Search and Society: Reimagining Information Access for Radical FuturesBhaskar Mitra
The field of Information retrieval (IR) is currently undergoing a transformative shift, at least partly due to the emerging applications of generative AI to information access. In this talk, we will deliberate on the sociotechnical implications of generative AI for information access. We will argue that there is both a critical necessity and an exciting opportunity for the IR community to re-center our research agendas on societal needs while dismantling the artificial separation between the work on fairness, accountability, transparency, and ethics in IR and the rest of IR research. Instead of adopting a reactionary strategy of trying to mitigate potential social harms from emerging technologies, the community should aim to proactively set the research agenda for the kinds of systems we should build inspired by diverse explicitly stated sociotechnical imaginaries. The sociotechnical imaginaries that underpin the design and development of information access technologies needs to be explicitly articulated, and we need to develop theories of change in context of these diverse perspectives. Our guiding future imaginaries must be informed by other academic fields, such as democratic theory and critical theory, and should be co-developed with social science scholars, legal scholars, civil rights and social justice activists, and artists, among others.
Kubernetes & AI - Beauty and the Beast !?! @KCD Istanbul 2024Tobias Schneck
As AI technology is pushing into IT I was wondering myself, as an “infrastructure container kubernetes guy”, how get this fancy AI technology get managed from an infrastructure operational view? Is it possible to apply our lovely cloud native principals as well? What benefit’s both technologies could bring to each other?
Let me take this questions and provide you a short journey through existing deployment models and use cases for AI software. On practical examples, we discuss what cloud/on-premise strategy we may need for applying it to our own infrastructure to get it to work from an enterprise perspective. I want to give an overview about infrastructure requirements and technologies, what could be beneficial or limiting your AI use cases in an enterprise environment. An interactive Demo will give you some insides, what approaches I got already working for real.
Key Trends Shaping the Future of Infrastructure.pdfCheryl Hung
Keynote at DIGIT West Expo, Glasgow on 29 May 2024.
Cheryl Hung, ochery.com
Sr Director, Infrastructure Ecosystem, Arm.
The key trends across hardware, cloud and open-source; exploring how these areas are likely to mature and develop over the short and long-term, and then considering how organisations can position themselves to adapt and thrive.
Dev Dives: Train smarter, not harder – active learning and UiPath LLMs for do...UiPathCommunity
💥 Speed, accuracy, and scaling – discover the superpowers of GenAI in action with UiPath Document Understanding and Communications Mining™:
See how to accelerate model training and optimize model performance with active learning
Learn about the latest enhancements to out-of-the-box document processing – with little to no training required
Get an exclusive demo of the new family of UiPath LLMs – GenAI models specialized for processing different types of documents and messages
This is a hands-on session specifically designed for automation developers and AI enthusiasts seeking to enhance their knowledge in leveraging the latest intelligent document processing capabilities offered by UiPath.
Speakers:
👨🏫 Andras Palfi, Senior Product Manager, UiPath
👩🏫 Lenka Dulovicova, Product Program Manager, UiPath
The Art of the Pitch: WordPress Relationships and SalesLaura Byrne
Clients don’t know what they don’t know. What web solutions are right for them? How does WordPress come into the picture? How do you make sure you understand scope and timeline? What do you do if sometime changes?
All these questions and more will be explored as we talk about matching clients’ needs with what your agency offers without pulling teeth or pulling your hair out. Practical tips, and strategies for successful relationship building that leads to closing the deal.
The Art of the Pitch: WordPress Relationships and Sales
Wcemc04
1. Page 1 of 6
CHP Case Studies – Saving Money and Increasing Security
Stephen F. Gillette
Capstone Turbine Corporation
ABSTRACT
Microturbines are excellent power generators for use in
combined heat and power (CHP) systems. Their low
maintenance and clean exhaust make them a reliable
choice for base load CHP applications. Integrating hot
water heat recovery into the microturbine package has
proven cost effective, and a growing number of
commercial installations are saving money using this
technology. Not only do microturbines provide this cost-
saving performance day in and day out, but their value is
further increased when the cost for traditional backup
generation is eliminated. The examples sited in this paper
are from the author’s company, Capstone Turbine, but are
intended to reflect the potential application of similar
microturbine products.
MICROTURBINE TECHNOLOGY OVERVIEW
There is no formal definition for a “microturbine,”
however the common characteristics of today’s products
are simple radial compressor and radial turbine designs
using a recuperator to preheat the combustion air for
improved efficiency. Most designs use a single shaft onto
which the radial compressor, radial turbine and generator
are all coupled. This assembly is sometimes called the
“turbo generator.” Rotating speeds are extremely high, in
the range of 45,000 to 100,000 revolutions per minute. The
generator output is therefore high frequency alternating
current. Figure 1 illustrates a microturbine turbo generator
with annular construction recuperator.
Power electronics are used to rectify this alternating
current to direct current, then invert to the three-phase 50
or 60 Hertz power frequency. Insulated gate bipolar
transistors (IGBT’s) are commonly used, and the power
electronics and controls are similar to technology used in
uninterruptible power supplies and variable frequency
motor drives. Integral computers control the conversion of
Figure 1 Turbo Generator Engine
power, operation of the turbo generator system, as well as
provide convenient man-machine interface and remote
communications. Because the designs are often so tightly
integrated with the onboard computer, operator interface
can be made both convenient and extremely powerful.
Protective relay functions are also often built into the
system, making microturbines extremely easy and safe to
connect in parallel with an electric grid. Figure 2 provides
a system diagram showing the key elements of such an
electronically controlled microturbine system. One
manufacturer uses a gearbox to transform the high-speed
turbine output to a more traditional synchronous speed
generator. In this case, synchronizing and protective
relaying control is done using traditional separate control
systems external to the microturbine.
2. Page 2 of 6
Microturbine turbo generators from most manufacturers
are able to operate on a variety of fuel types: natural gas,
biogas, diesel fuel, or propane. One of the characteristics of
microturbines is that the fuel must be injected into the
combustion chamber at relatively high pressure of three to
five atmospheres. When using gaseous fuels, this
requirement for fuel compression requires significant
power, which must be considered part of the microturbine
system when calculating net power output. Several
manufacturers offer a natural gas compressor either
internal to the microturbine package or directly powered
and automatically controlled by the microturbine in order
to simplify installation.
Current production microturbines range in net power
output from 28 to 250kW. The standard used by
manufacturers for rating power and electrical efficiency for
microturbines is at ISO ambient conditions of 15°C (59°F)
and sea level. Electrical efficiencies relate to the lower
heating value of the fuel (LHV), and are typically from the
mid-twenty to low-thirty percent range, depending on fuel
type and fuel compressor parasitic load. As with all
Brayton cycle engines, the power and efficiency are both
reduced with increased ambient temperature, resulting in
performance de-rating curves, which can be obtained from
the manufacturer for each specific microturbine.
Microturbines do not have reciprocating parts that require
frequent change of lubricants. Some microturbines even
utilize air bearings and air cooling, thereby completely
eliminating the need to change and dispose of hazardous
liquid lubricants and coolants. In any case, microturbines
are similar to major power plants, able to run for extended
periods at full power output, and require little scheduled
maintenance compared with traditional reciprocating
engines of similar size. This makes them ideal for
stationary prime power applications.
The combustion process in a microturbine is continuous
and clean burning, similar to modern gas turbine power
plants. Microturbine manufacturers have deployed state-of-
the-art lean-burn combustion technology to control
emissions without the need for expensive catalytic exhaust
treatment equipment or chemicals. The leading microtur-
bine manufacturers specify fewer than 9 parts per million
(ppm) NOx (0.47 pounds per megawatt-hour) and similar
emissions of CO at full power, and independent third
parties have verified that emissions measurements are
actually much lower. Because their exhaust is so clean,
microturbines are relatively easy to site virtually anywhere.
In Southern California, which has some of the strictest
emissions standards in the world, most manufacturers have
already deployed microturbines. In addition, the California
Air Resources Board (CARB) set new emissions
regulations for microturbines effective January 1, 2003,
that are output based and must be measured over several
real-world operating conditions. At least two microturbine
manufacturers have now met this strict standard, and have
had microturbine products certified to meet the CARB
standard. Future standards, set to be imposed in 2007, will
be even more stringent. This type of regulation is already
facilitating installation of microturbines in California, and
may become more widely accepted in all markets.
INTEGRATED CHP SYSTEMS
The benefits of combining the thermal and electrical
outputs of a system are widely recognized. Extracting the
exhaust energy that would otherwise be wasted increases
the total system efficiency far beyond that of fossil-fueled
utility power plants. This means more useful work from
our limited natural resources, and less greenhouse gas
emissions than using conventional energy conversion
technologies. And since microturbines are already
extremely clean burning, other exhaust emissions are
reduced as well. Figure 3 provides an example comparing
efficiency and emissions for traditional and microCHP
systems with 60 kW electric output and 120 kW heat
output. Note that total efficiency is significantly higher,
greenhouse gas emissions (CO2) are 25% less, and NOx
emissions are an order of magnitude lower for the micro-
CHP system shown. Reference emissions for the traditional
system are extracted from published US Department of
Energy data on efficiency and emissions from the average
US fossil fuel power plant, according to US EPA data.
Figure 2. – Typical Microturbine System
Fuel
System
MicroTurbine
Generator
Power
Controller
Control
Computer
Battery
(Optional)
User Interface
Exhaust
Electrical
Output
Fuel
Supply
Air
Figure 3. – Traditional vs MicroCHP System
Water Heater
80% Efficient
+
150kW
Fuel
US Average
33% Efficient
180kW
Fuel
60kW
Electricity
120kW
Hot Water
30kW
Waste
240kW
Fuel
60kW
Electricity
Microturbine
Heat
Exchanger
120kW
Hot Water
60kW
Waste
Traditional MicroCHP
• 57% Total Efficiency
• 0.2 lb/hr NOx
• 120 lb/hr CO2
• 75% Total Efficiency
• 0.02 lb/hr NOx
• 90 lb/hr CO2
Water Heater
80% Efficient
+
150kW
Fuel
US Average
33% Efficient
180kW
Fuel
60kW
Electricity
120kW
Hot Water
30kW
Waste
240kW
Fuel
60kW
Electricity
Microturbine
Heat
Exchanger
120kW
Hot Water
60kW
Waste
Water Heater
80% Efficient
+
150kW
Fuel
US Average
33% Efficient
180kW
Fuel
60kW
Electricity
US Average
33% Efficient
180kW
Fuel
60kW
Electricity
120kW
Hot Water
30kW
Waste
240kW
Fuel
60kW
Electricity
Microturbine
Heat
Exchanger
120kW
Hot Water
60kW
Waste
240kW
Fuel
60kW
Electricity
Microturbine
Heat
Exchanger
120kW
Hot Water
60kW
Waste
Traditional MicroCHP
• 57% Total Efficiency
• 0.2 lb/hr NOx
• 120 lb/hr CO2
• 75% Total Efficiency
• 0.02 lb/hr NOx
• 90 lb/hr CO2
3. Page 3 of 6
These benefits of combined heat and power systems are
significant for the environment and for energy
conservation. National and state governments recognize
the social values of such CHP systems, and often provide
incentives to help develop new installations. For example,
in California, the Public Utilities Commission provides up
to 30% rebates for CHP installations that meet certain size
and efficiency requirements; 40% if biogas fueled. The
economic benefit of such microturbine-based CHP systems
are becoming well accepted in the market, and example
installations will be covered later in this paper.
To continue this adoption trend, however, microCHP
systems must become even easier to apply and install. One
example is the Capstone C60 Integrated CHP System
(C60-ICHP), released in September 2003. It is, in many
ways, similar to integrated CHP systems offered by Inger-
soll-Rand and others. The Capstone C60-ICHP system was
described in detail in a related AEE paper presented at
Globalcon in Boston, Massachusetts March 24, 2004.
Figure 4 shows the C60-ICHP System.
CHP CASE STUDY #1 – RADISSON HOTEL
Two C60-ICHP systems are installed at the Radisson Hotel
in Santa Maria, California. In this application, the hot
water output is used for several different purposes. One use
is for domestic hot water for the hotel guests. This thermal
load is highest in the morning, and then increases again
later in the day. A second use is for laundry service. This is
highest during the working day. The third use is for
building heat. This load is seasonal, and steady during the
day when outside temperatures are low. Figure 5 shows the
installation of these two C60-ICHP units at the hotel.
The two C60-ICHP systems are set to operate in parallel
with the electric grid, and Electric Priority mode is used. In
this CHP mode, the electric power output for each
microturbine is set at the desired level. For this Radisson
hotel with 188 rooms, electric power is normally set for
maximum from each microturbine during the day. This is
below the building’s peak electric demand, and power does
not flow back into the electric utility grid. While the
microturbines work to maintain their programmed electri-
cal outputs, the exhaust diverters automatically adjust to
accommodate the changing thermal requirements of the
hotel. This example shows how the flexible control capa-
bilities of the C60-ICHP allow simple integration with a
building with changing thermal requirements.
The two C60-ICHP systems are set to operate 24 hours per
day. The operating scheme was selected to match the
thermal requirements of the hotel, provide the maximum
electric energy, and reduce time-of-use demand charges
from the local electric utility. This results in maximum
financial benefit to the hotel, and helps to offload the
utility when power is needed most by other customers. The
hotel’s electrical utility is PG&E, its gas utility is Sempra’s
SoCalGasCo. PowerHouse Energy supplied the ICHP
systems to the hotel and managed the installation, system
startup and continuous operation.
The ICHP application qualified for the state’s PUC Self-
Generation Incentive Program rebate of 30% on the total
installed cost. The expected energy savings are very good,
with a calculated average savings of about $5,528 a month
or $66,336 per year. This savings to the hotel is net of
natural gas, projected lifecycle maintenance costs, and
project financing. Total installed cost was $185,000 (net of
the PUC rebate), giving this project a respectable 32%
IRR. The operating availability of the ICHP systems, in-
cluding start up, commissioning, and service response time
has been better than 95% to date.
Figure 4. – C60 Integrated CHP System
Figure 5. – Two C60-ICHPs at Radisson Santa Maria
4. Page 4 of 6
CHP CASE STUDY #2 – INNS OF AMERICA
The Capstone microturbine installation at Inns of America
in Carlsbad, California, was completed in August 2002 by
California Power Partners (Calpwr). It included a Capstone
C60 with fuel gas booster and separate hot water heat
recovery module. Figure 6 shows the hotel with an inset
photo of the 60 kW microturbine. As for the Radisson, this
microCHP system provides both thermal and electric base
load for this hotel. Energy savings were estimated at 40%.
This lowered the daily per room energy cost by $4.00 – a
significant portion of the hotel’s profit margin.
While this installation is saving the hotel owner money
every day, there is a unique attribute that provided even
more value than anyone envisioned when the decision to
purchase this system was made. The hotel owner decided
to purchase Capstone’s dual mode version microturbine,
with the capability to provide power even when the electric
utility is not available. The logic was to avoid the cost of a
traditional backup generator, thereby improving the eco-
nomics of this project. Such traditional diesel backup
generators are designed and permitted to operate only for
short periods of time in case of a utility outage. But mic-
roturbines certified by the California Air Resources Board
can operate continuously without the need for local air
permits.
In October of 2003, Southern California was ravaged by
multiple wildfires that lasted days and crippled the state
with huge property and personal losses. Carlsbad, where
the hotel is located, and the nearby San Diego region were
especially hard hit. Power lines were shut down, and many
homes and businesses. Figure 7 is a satellite picture of
Southern California that shows the breadth of the fires’
destruction.
During this time, the Inns of America lights remained on,
powered by the Capstone 60kW microturbine. In support
of the local community, the Inns donated a number of
rooms for people who were displaced or otherwise in need.
Local businesses began using the hotel’s business center,
and the Inns of America became an emergency base of
operations for several groups. The result for the hotel was
increased business and a strengthened relationship with the
community – things that were never directly considered in
their original decision to install a microCHP system.
CHP CASE STUDY #3 – BAULI RESTAURANT
The US is not alone in facing extended power outages. On
September 28, 2003 Italy faced a multi-hour power outage.
The Bauli Grill restaurant in Verona had already installed a
Capstone C60 microturbine-based CHP system with the
help of the national electric utility. The primary driver for
this installation was cost savings, made possible with the
highly energy efficient CHP solution shown in figure 8.
Figure 7. – Satellite Photo of California Wild Fires
Figure 6. –C60 CHP System at Inns of America
Figure 8. – C60 CHP System at Bauli Restaurant
5. Page 5 of 6
The Bauli Grill is a full service convenience restaurant
located on the Autostrada, and operates 24 hours a day. At
about 3:30 a.m., the utility power failed. The microCHP
system was not operating at that time, as there was insuffi-
cient thermal load to make operation economical at that
early hour. However, as soon as the outage occured, the
Capstone C60 started up to provide power to critical loads
in the restaurant. This continued until about 7:30 a.m.
when utility power was restored. Figure 9 shows power
data that was recorded by the electric utility, ENEL.
Figure 9. – Bauli Grill Power Outage
0.00
10.00
20.00
30.00
40.00
50.00
60.00
70.00
80.00
90.00
3.20
6.40
Hours
kW
Start BLACK OUT
BLACK OUT stop
Cogeneration Unit in stand alone mode
Battery
recharge
Cogeneration
Unit stopped for
no request of
thermal energy
Cogeneration
Unit in grid
connect
This roadside restaurant continued to stay open and serve
travelers while virtually all of Italy was without power.
Based on this demonstrated reliability and the good CHP
economics, the owners of the Bauli Grill chain are now
considering additional installations at their other locations.
EXPECT LONGER POWER OUTAGES
Southern California and Italy are not the only areas to be
impacted by extended power outages. Whether due to
natural disaster (as was the case of the Southern California
wildfires), or the result of over-burdened utility grids (as
was the case of the August 2003 Northeast blackout),
power outages can last for many hours or even days.
In fact, there is growing concern by many in the power
industry that we face a threat of longer duration power
outages in the future. In a whitepaper entitled Critical
Power (ref www.digitalpowergroup.com), the authors des-
cribe the potential for sabotage to increase the duration of
power outages many hours to days. Figure 10 compares
this new sabotage factor to historical outage frequency and
duration curves used to design high reliability power
systems.
We can expect that security of power will become even
more important to government and private industry, and
the quickest way to achieve higher levels of security is
through onsite power generation.
TRADITIONAL BACKUP IS NOT ENOUGH
Diesel backup generators are traditionally used to protect
against extended utility power outages. However, they of-
ten fall short of expectations – especially during extended
outages.
During the August 2003 Northeast blackout, about half of
New York City’s 58 hospitals suffered backup power
failures. The reasons for this poor performance included
inability to start, breakdown after starting, and lack of suf-
ficient fuel to continue operation. The impact was exacer-
bated by the common practice of installing only one
backup generator for critical loads. The New York Daily
News described the resulting shuttling of patients from
hospital to hospital in hopes of finding one with backup
power “hospital hopscotch.”
The Wall Street Journal reported some New York hotel
operators with diesel backup generators limited the number
of loads that were protected for fear that they would run
out of fuel. And the industry’s Lodging magazine reported
that, like those at New York City hospitals, many backup
generators could not be started or failed when presented
with real-world conditions.
Solutions will include addressing problems with starting,
extending fuel supply, and adding redundancy. Natural gas
fired microCHP systems can cost-effectively address all
these elements of good design practice. Since they run for
extended periods every day (or continuously), the problems
associated with infrequent starting are not an issue. For
most outage scenarios, the natural gas supply remains
available (in fact, several Capstone microturbines at a
natural gas transmission plant in Ithaca, New York, kept
the gas flowing throughout the outage).
Figure 10. – Electric Grid Failures
6. Page 6 of 6
Combining microturbines into a multipac system results in
higher total system availability. And the best part is that a
microCHP system pays for itself with energy savings.
Figure 11 shows a sample calculation of how a hot water
CHP system can result in 40% savings compared to pur-
chasing power from a utility and sinking capital into a
backup generator.
Figure 11. – Energy Savings Comparison
Commercial Electricity Cost Comparison
-$0.04
-$0.02
$0.00
$0.02
$0.04
$0.06
$0.08
$0.10
$0.12
$0.14
$/kWh
CA Utility Avg
Fuel Offset
Maintenance
Installation
Equipment
Net Fuel
Source for Utility Tariffs: EIA 2002 Survey
Utility Price CHP
40% Savings
THE FUTURE IS EVEN MORE POWERFULL
The examples shown in this paper were all microCHP
systems using hot water as the thermal load. As shown in
the economics above, the savings can be dramatic where
hot water thermal loads exist; such as in hotels, restaurants,
schools, swimming pools and spas, and many industrial
processes. There is a much larger potential market for cost-
effective combined cooling, heating, and power systems
(sometimes referred to as CCHP) or trigeneration.
Figure 12. –UTC Power’s PureComfort 240M
United Technologies Corporation (UTC) recently intro-
duced a dual-effect absorption chiller – with approximately
twice the energy efficiency of single-effect chillers – that is
able to directly accept the exhaust from four 60-kW micro-
turbines. This product was developed with support from
UTC’s Carrier Corporation and the United Technologies
Research Center, and is marketed through UTC Power.
The first product is labeled “PureComfort 240M,” and is
offered as a complete trigeneration solution – including
microturbines, chiller, and pre-engineered exhaust ducting
and controls. Figure 12 shows the microturbines and ex-
haust ducting to the chiller during product development.
UTC Power has received several orders for the
PureComfort 240M, the first of which is scheduled for
installation this summer.
Several examples of microturbine-driven combined cool-
ing and power systems are now operating, using hot water
driven absorption chillers and even direct-exhaust-fired
chillers. As these combined cooling and power technol-
ogies continue to mature, the economic benefit will be-
come viable for a significant number of commercial and
industrial customers. The option to integrate backup func-
tionality for these systems adds even more value for the
increasing number of customers who are concerned about
security of power. And since summertime load demands,
and utility rates, double or triple in summer months,
creating chilled water and air using heat energy instead of
electric energy makes great sense.
CONCLUSION
Microturbines continue to find economic application in a
growing market. Integration of hot water heat recovery,
absorption chilling, and backup power functions makes for
simple solutions that save money and increase power
reliability, with the added social benefits of clean emis-
sions, reduced greenhouse gas production, and more effi-
cient use of our limited natural resources. The microCHP
case studies in this paper are just a few examples of real
commercial customers taking financial advantage of micro-
turbine technology, and commercial microCCHP case
studies are just around the corner.