For application of PV systems, a major deterrent factor in their use is high initial investment. A focus has therefore been placed on new, cheap and innovative inverter solutions. As a result of this, a single stage inverter topology and a new configuration are proposed. In two stage circuit, the first stage takes care of MPPT and boosting the PV voltage while second stage inverts the first stage output into the required AC form. A two stage configuration has drawbacks such as high part count, lower efficiency, lower reliability, high cost and large size. These drawbacks are overcome by the circuit proposed in this paper. The new inverter circuit proposed in this paper is designed and simulated in a simulation environment. The improved topology increases the voltage, reduces the power loss and enhances the various electrical parameters. This enhancement and improvement of electrical quantities is explained with the help of different formulae and figures. With the use of this improve circuitry; the efficiency of the PV Array can be increased. The proposed inverter design and its implementation are given with operational results.
This paper presents the design and the implementation of a new microcontroller-based solar
Power inverter. The aim of this paper is to design single phase inverter which can convert DC voltage
to AC voltage at high efficiency and low cost. Solar and wind powered electricity generation are
being favored nowadays as the world increasingly focuses on environmental concerns. Power
inverters, which convert solar-cell DC into domestic-use AC, are one of the key technologies for
delivering efficient AC power The hardware and software design are oriented towards a single-chip
microcontroller-based system, hence minimizing the size and cost. With this new approach the
modularization of the conversion from solar power to electric power at its maximum power point can
be made more compact and more reliable.
Hydraulics now a days is a very distinguished area which has lot of major challenges often came in its
progress due to the realistic changes affecting on applicable working fluid viz. Water. Most occasions,
Water can be easily available but in certain times it may be scarce also. The available water vary according
to its properties. It exists in normal conditions as well as salty or hardy due to deposits. Majority of Water
is contaminated with minerals, dust or dirt. Often pure water which may be acidic or alkaline can be used
for making discharges through the Turbines
Benefits: 20-30% extra energy, Ease of Installation & Expandable, No Single Point of Failure, Improved Safety, Low Space & No Heating, Longer Life, Silent
HIGH EFFICIENT BRIDGELESS BOOST RECTIFIER FOR LOW VOLTAGE ENERGY HARVESTING A...IAEME Publication
A single phase ac-dc bridgeless boost rectifier for low voltage energy harvesting applications is proposed in this paper. The conventional bridge type boost converters for low voltage energy harvesting requires more components hence they suffer from high power loss and require more number of energy storage components like inductors and capacitors. Conventional converters can be modeled for boost operation or buck-boost operation alone. The proposed converter overcomes the above mentioned draw backs of conventional converter. Detailed analysis of proposed convertor is also presented under boost, buck-boost mode operations. The proposed converter operation is analyzed using MATLAB/SIMULINK environment both open loop and closed loop conditions.
This paper presents the design and the implementation of a new microcontroller-based solar
Power inverter. The aim of this paper is to design single phase inverter which can convert DC voltage
to AC voltage at high efficiency and low cost. Solar and wind powered electricity generation are
being favored nowadays as the world increasingly focuses on environmental concerns. Power
inverters, which convert solar-cell DC into domestic-use AC, are one of the key technologies for
delivering efficient AC power The hardware and software design are oriented towards a single-chip
microcontroller-based system, hence minimizing the size and cost. With this new approach the
modularization of the conversion from solar power to electric power at its maximum power point can
be made more compact and more reliable.
Hydraulics now a days is a very distinguished area which has lot of major challenges often came in its
progress due to the realistic changes affecting on applicable working fluid viz. Water. Most occasions,
Water can be easily available but in certain times it may be scarce also. The available water vary according
to its properties. It exists in normal conditions as well as salty or hardy due to deposits. Majority of Water
is contaminated with minerals, dust or dirt. Often pure water which may be acidic or alkaline can be used
for making discharges through the Turbines
Benefits: 20-30% extra energy, Ease of Installation & Expandable, No Single Point of Failure, Improved Safety, Low Space & No Heating, Longer Life, Silent
HIGH EFFICIENT BRIDGELESS BOOST RECTIFIER FOR LOW VOLTAGE ENERGY HARVESTING A...IAEME Publication
A single phase ac-dc bridgeless boost rectifier for low voltage energy harvesting applications is proposed in this paper. The conventional bridge type boost converters for low voltage energy harvesting requires more components hence they suffer from high power loss and require more number of energy storage components like inductors and capacitors. Conventional converters can be modeled for boost operation or buck-boost operation alone. The proposed converter overcomes the above mentioned draw backs of conventional converter. Detailed analysis of proposed convertor is also presented under boost, buck-boost mode operations. The proposed converter operation is analyzed using MATLAB/SIMULINK environment both open loop and closed loop conditions.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
This paper proposes the design and development of Arduino based solar charge controller with sun tracking using PWM technique. This PWM technique is employed using ATmega328P on Arduino board. The Arduino is used to charge a 12V battery using 10W solar panel. The main feature of this charge controller is to control the load. During day time when load is not connected the battery gets charged from solar panel. When battery reaches peak value of 14.7V charging current & further charging is interrupted by Arduino. An inbuilt analogue to digital converter is used to determine voltage of battery, solar panel and current drawn by the load. A solar tracking system is also implemented such that panel is always kept at right angle to incident radiation.
Isolated Wind Hydro Hybrid Generation System with Battery StorageIJMER
In this paper, a new isolated wind- hydro hybrid generation system comprising one squirrel -cage induction generator (SCIG) driven by a variable-speed wind turbine and another synchronous generator driven by constant power hydro turbine feeding three phase four wire local loads is proposed. The system utilizes two back to back connected voltage-source converters (VSCs) with a battery energy storage system at their dc link. The main objective of the control algorithm for the VSC is to achieve control of the magnitude and the frequency of the load voltage. The proposed wind-hydro hybrid system has a capability of bidirectional active- and reactive-power flow, by which it controls the magnitude and the frequency of the load voltage. The proposed electromechanical system is modelled and simulated in MATLAB using Simulink.
Harvesting energy from the sun makes the photovoltaic (PV) power generation a promising technology. To obtain a consistent state of charge (SOC), consistent energy must be harvested and efficiently directed to the battery. Overcharging or undercharging phenomena decreases the lifetime of the battery. Besides, the effect of irradiance toward solar in term of sunlight intensity effects the efficiency and hence, sluggish the SOC. The main problem of the solar panel revealed when the temperature has increased, the efficiency of solar panel will also be decreased. This manuscript reports the finding of developing an automatic active cooling system for a solar panel with a real time energy monitoring system with internet-of-things (IoT) facility. The IoT technology assists user to measure the efficiency of the solar panel and SOC of the battery in real time from any locations. The automatic active cooling system is designed to improve the efficiency of the solar panel. The effectiveness of the proposed system is proven via the analysis of the effect of active cooling toward efficiency and SOC of photovoltaic system. The results also tabulate the comparative studies of active-to-passive cooling system, as well as the effect of cooling towards SOC and efficiency of the solar panel.
DFIG control of WECS using indirect matrix converter Kuldeep Behera
The connection and operation of wind power plants produce some problems that are rising partly owing to large changeability of environment conditions, influencing the electrical energy supply from these sources. To be possible to study phenomena that are connected with wind power plants and impacts of their operation on the operation of distribution and transmission systems, it is necessary to do such as in other branches, different computer simulations. A grid connected wind power generation scheme using doubly fed induction generator is studied. The aim is modelling and simulation of DFIG operating in two quadrants (torque-speed) by a suitable control technique to control the rotor current. This method will also replace the conventional converter by Indirect Matrix Converter.
Performance of Photovoltaic Assisted Five Level Diode Clamped Inverter fed In...IJMTST Journal
This paper presents the simulation and analysis of Photovoltaic assisted three phase five level Diode Clamped multilevel inverter fed induction motor drive. Photovoltaic technology is one of the most promising for distributed low power generation. Its ability to produce power by directly converting solar energy has led to tremendous surge in its demand. The Photovoltaic output DC is fed to the boost converter to step up the voltage. The use of multilevel inverters have become popular in recent years for high power applications and an effective and practical solution for increasing power and reducing harmonics of AC waveforms. So, here a five level multilevel inverter is used for generating AC voltage from five levels of DC voltages and enhance the performance of the system. The proposed system is used to reduce the amplitudes of all harmonics at the output of the inverter. The power quality improves by reducing the harmonics level. The simulation results for the proposed system are verified using Mat lab / Simulink. The TOTAL HARMONIC DISTORTION (THD) for Diode Clamped multi-level inverter is compared with the three phase inverter and it can be observed that in the higher levels the THD is reduced.
A Matlab/Simulink Model for the control scheme utilized to improve power qual...AM Publications
the wind energy generation, utilization and its grid penetration in electrical grid are increasing worldwide. The
integration of wind energy into the power system is to minimize the environmental impact on conventional plant but the injection
of the wind power into an electric grid affects the power quality. The wind generated power is always fluctuating due to its time
varying nature and causing stability problem. The power quality is determined on the basis of measurements and the norms
followed according to the guideline specified in International Electro-technical Commission standard, IEC-61400. The influence
of the wind turbine in the grid system concerning the power quality measurements are-the active power, reactive power, variation
of voltage, flicker, harmonics, and electrical behavior of switching operation and these are measured according to
national/international guidelines. The project demonstrates the power quality problem due to installation of wind turbine with
the grid. In this proposed scheme Static Compensator (STATCOM) is connected at a point of common coupling with a battery
energy storage system (BESS) to mitigate the harmonics. The battery energy storage is integrated to sustain the real power
source under fluctuating wind power. The STATCOM control scheme for the grid connected wind energy generation system for
power quality improvement is simulated using MATLAB/SIMULINK in power system block set. The effectiveness of the
proposed scheme relives the main supply source from the reactive power demand of the load and the induction generator. The
development of the grid co-ordination rule and the scheme for improvement in power quality norms as per IEC-standard on the grid has been presented.
Z-Source Based High Step-Up Chopper for Photovoltaic PanelAM Publications
The photovoltaic panel not only generates low DC voltage but also DC voltage which varies with time and environmental condition. Therefore design of electrical energy system with constant output voltage is a big challenge to designer. This project deals with the development of electrical energy system which consists of Z-source based high step up chopper. The chopper is basically based on coupled inductor which provides high voltage gain and physical isolation between input and output with small turn ratio. It also provides a low voltage stress on active components and small conduction losses due to low duty cycle. Due to the usage of a single switch, the control circuitry is less complex. The proposed chopper recycles the energy of leakage inductance hence enhancing system efficiency. This report consists of mathematical modelling and designing of proposed chopper circuit. The MATLAB simulation of proposed chopper circuit is to convert 25 volts dc to 400 volts dc with 300 watts power. The simulation results validate the theoretical results. The H-Bridge inverter circuit is used at the end of proposed chopper for converting DC voltage into AC voltage.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
This paper proposes the design and development of Arduino based solar charge controller with sun tracking using PWM technique. This PWM technique is employed using ATmega328P on Arduino board. The Arduino is used to charge a 12V battery using 10W solar panel. The main feature of this charge controller is to control the load. During day time when load is not connected the battery gets charged from solar panel. When battery reaches peak value of 14.7V charging current & further charging is interrupted by Arduino. An inbuilt analogue to digital converter is used to determine voltage of battery, solar panel and current drawn by the load. A solar tracking system is also implemented such that panel is always kept at right angle to incident radiation.
Isolated Wind Hydro Hybrid Generation System with Battery StorageIJMER
In this paper, a new isolated wind- hydro hybrid generation system comprising one squirrel -cage induction generator (SCIG) driven by a variable-speed wind turbine and another synchronous generator driven by constant power hydro turbine feeding three phase four wire local loads is proposed. The system utilizes two back to back connected voltage-source converters (VSCs) with a battery energy storage system at their dc link. The main objective of the control algorithm for the VSC is to achieve control of the magnitude and the frequency of the load voltage. The proposed wind-hydro hybrid system has a capability of bidirectional active- and reactive-power flow, by which it controls the magnitude and the frequency of the load voltage. The proposed electromechanical system is modelled and simulated in MATLAB using Simulink.
Harvesting energy from the sun makes the photovoltaic (PV) power generation a promising technology. To obtain a consistent state of charge (SOC), consistent energy must be harvested and efficiently directed to the battery. Overcharging or undercharging phenomena decreases the lifetime of the battery. Besides, the effect of irradiance toward solar in term of sunlight intensity effects the efficiency and hence, sluggish the SOC. The main problem of the solar panel revealed when the temperature has increased, the efficiency of solar panel will also be decreased. This manuscript reports the finding of developing an automatic active cooling system for a solar panel with a real time energy monitoring system with internet-of-things (IoT) facility. The IoT technology assists user to measure the efficiency of the solar panel and SOC of the battery in real time from any locations. The automatic active cooling system is designed to improve the efficiency of the solar panel. The effectiveness of the proposed system is proven via the analysis of the effect of active cooling toward efficiency and SOC of photovoltaic system. The results also tabulate the comparative studies of active-to-passive cooling system, as well as the effect of cooling towards SOC and efficiency of the solar panel.
DFIG control of WECS using indirect matrix converter Kuldeep Behera
The connection and operation of wind power plants produce some problems that are rising partly owing to large changeability of environment conditions, influencing the electrical energy supply from these sources. To be possible to study phenomena that are connected with wind power plants and impacts of their operation on the operation of distribution and transmission systems, it is necessary to do such as in other branches, different computer simulations. A grid connected wind power generation scheme using doubly fed induction generator is studied. The aim is modelling and simulation of DFIG operating in two quadrants (torque-speed) by a suitable control technique to control the rotor current. This method will also replace the conventional converter by Indirect Matrix Converter.
Performance of Photovoltaic Assisted Five Level Diode Clamped Inverter fed In...IJMTST Journal
This paper presents the simulation and analysis of Photovoltaic assisted three phase five level Diode Clamped multilevel inverter fed induction motor drive. Photovoltaic technology is one of the most promising for distributed low power generation. Its ability to produce power by directly converting solar energy has led to tremendous surge in its demand. The Photovoltaic output DC is fed to the boost converter to step up the voltage. The use of multilevel inverters have become popular in recent years for high power applications and an effective and practical solution for increasing power and reducing harmonics of AC waveforms. So, here a five level multilevel inverter is used for generating AC voltage from five levels of DC voltages and enhance the performance of the system. The proposed system is used to reduce the amplitudes of all harmonics at the output of the inverter. The power quality improves by reducing the harmonics level. The simulation results for the proposed system are verified using Mat lab / Simulink. The TOTAL HARMONIC DISTORTION (THD) for Diode Clamped multi-level inverter is compared with the three phase inverter and it can be observed that in the higher levels the THD is reduced.
A Matlab/Simulink Model for the control scheme utilized to improve power qual...AM Publications
the wind energy generation, utilization and its grid penetration in electrical grid are increasing worldwide. The
integration of wind energy into the power system is to minimize the environmental impact on conventional plant but the injection
of the wind power into an electric grid affects the power quality. The wind generated power is always fluctuating due to its time
varying nature and causing stability problem. The power quality is determined on the basis of measurements and the norms
followed according to the guideline specified in International Electro-technical Commission standard, IEC-61400. The influence
of the wind turbine in the grid system concerning the power quality measurements are-the active power, reactive power, variation
of voltage, flicker, harmonics, and electrical behavior of switching operation and these are measured according to
national/international guidelines. The project demonstrates the power quality problem due to installation of wind turbine with
the grid. In this proposed scheme Static Compensator (STATCOM) is connected at a point of common coupling with a battery
energy storage system (BESS) to mitigate the harmonics. The battery energy storage is integrated to sustain the real power
source under fluctuating wind power. The STATCOM control scheme for the grid connected wind energy generation system for
power quality improvement is simulated using MATLAB/SIMULINK in power system block set. The effectiveness of the
proposed scheme relives the main supply source from the reactive power demand of the load and the induction generator. The
development of the grid co-ordination rule and the scheme for improvement in power quality norms as per IEC-standard on the grid has been presented.
Z-Source Based High Step-Up Chopper for Photovoltaic PanelAM Publications
The photovoltaic panel not only generates low DC voltage but also DC voltage which varies with time and environmental condition. Therefore design of electrical energy system with constant output voltage is a big challenge to designer. This project deals with the development of electrical energy system which consists of Z-source based high step up chopper. The chopper is basically based on coupled inductor which provides high voltage gain and physical isolation between input and output with small turn ratio. It also provides a low voltage stress on active components and small conduction losses due to low duty cycle. Due to the usage of a single switch, the control circuitry is less complex. The proposed chopper recycles the energy of leakage inductance hence enhancing system efficiency. This report consists of mathematical modelling and designing of proposed chopper circuit. The MATLAB simulation of proposed chopper circuit is to convert 25 volts dc to 400 volts dc with 300 watts power. The simulation results validate the theoretical results. The H-Bridge inverter circuit is used at the end of proposed chopper for converting DC voltage into AC voltage.
Pi controller based of multi level upqc using dq0 transformation to improve p...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Renewable Energy Based on Current Fed Switched Inverter for Smart Grid Applic...MangaiK4
Abstract - Renewable energy is used in the current fed switched inverter for high power production. High voltage support, wide yield ranges of operation, shoot-through resistance are a portion of the desired properties of an inverter for a reliable, versatile and less ripple AC inversion. This paper proposes a single stage, high boost inverter with buck-boost capacity which has a few particular advantages over traditional voltage source inverters (VSI) like better EMI noise, wide input and output voltage range of operation, and so on. The proposed inverter is named as Current-Fed Switched Inverter (CFSI). A renewable energy based converter structure of CFSI has been created which supplies both AC and DC loads, at the same time, from a single DC supply which makes it reasonable for DC smart grid application. This paper proposes the operation and control of a CFSI based converter which directs the AC and DC conversion voltages at their reference. The advancement of the proposed converter from essential current fed DC/DC topology is explained. The closed loop controller is verified by using the MATLAB/ Simulink environment.
DEVELOPMENT OF TODDLER FAMILY CADRE TRAINING BASED ON ANDROID APPLICATIONS IN...AM Publications
Toddler family cadre is a community members work voluntarily in fostering and providing information to parents of toddlers about how to properly care for children. Toddler Family cadre desperately need training to increase their skills. There are still a few Toddler family cadres who get training so that the knowledge and skills of parents and other family members in developing toddlers' growth through physical stimulation, motoric intelligence, emotional and social economy as well as possible are still lacking. The purpose of this study is to develop an Android- assisted Toddler family cadre training model in Demak. This research is research in tian research and development. The research location was in Demak Regency. Toddler family cadres became the object of this research. Development of Toddler family cadre training models assisted by Android in Demak is feasible to be used as an effort to improve Toddler Family cadres' capabilities.
TESTING OF COMPOSITE ON DROP-WEIGHT IMPACT TESTING AND DAMAGE IDENTIFICATION ...AM Publications
In recent years the use of composite materials in structural components has become increasingly common in a wide range of engineering applications. Composite materials offer numerous advantages over more conventional materials because of their superior specific properties, but a serious obstacle to a more widespread use of these materials is their high sensitivity to localized impact loading. This paper presents an experimental study to assess the impact response of drop weight impact tests on fiber reinforced polymer composites with deferent load and damage identification of composite using Non-destructive testing techniques ultrasonic testing (UT) C scan. In the study includes checking the strength of the specimen, plotting of graphs between the height and the impact energy obtained and tabulating the results after conducting the various functional tests.
THE USE OF FRACTAL GEOMETRY IN TILING MOTIF DESIGNAM Publications
In this paper I will present the use of fractal geometry to design tile motifs. A fractal is a geometric figure that combines the several characteristics among others: its parts have the same form as the whole, fragmented, and formation by iteration. The concept of fractals has been spread over all fields of sciences, technology, and art. This paper aims to provide an algorithm to creating motifs of tile algorithm for create the tile motif consists of base, iteration, coloration and duplication. In order to help the reader better understand the algorithm, I will present some script using Matlab. We describe a mathematically based algorithm that can fill a spatial region with sequence of randomly placed which may be transformed copies of one motif or several motifs. By using this algorithm, I can produce thousand variety of aesthetically pleasing tile motifs, of which we show a number of examples.
TWO-DIMENSIONAL INVERSION FINITE ELEMENT MODELING OF MAGNETOTELLURIC DATA: CA...AM Publications
Two-dimensional resistivity analysis of magnetotelluric data has been done at “Z” geothermal area which is located in southern part of Indonesia. The objective is to understand subsurface structure beneath reasearch area based on 2-D modeling of magnetotelluric data. The inversion finite element method were used for numerical simulations which requires discretization on the boundary of the modeling domain. The modeling results of magnetotelluric data shows relativity structure dissemination: 0-10 ohm.m in a thickness of 1 km (Clay Cap), 10-100 ohm.m with 1-2 km depth respectively (reservoir zone), and on a scale of 100-1000 ohm.m in a depth of 2-3 km (heat source zone). The result of relativity structure can be used to delineate an area with geothermal prospect around 12 km2.
USING THE GENETIC ALGORITHM TO OPTIMIZE LASER WELDING PARAMETERS FOR MARTENSI...AM Publications
To achieve the pre-set welding size, this paper presents the optimization of the constrained overlap laser welding input parameters for AISI 416 and AISI 440FSe stainless, thickness 0.5 mm. In this study, the proposed optimization algorithm is the Genetic Algorithm (GA). After training 10 times for 30 NP (population size), each training repeated 200 times, the results achieved as expected. The error is compared with the result of the affirmation experiment not exceeding 5%.
ANALYSIS AND DESIGN E-MARKETPLACE FOR MICRO, SMALL AND MEDIUM ENTERPRISESAM Publications
The Ministry of Cooperatives and Small and Medium Enterprises launched in 2018 the number of Micro, Small and Medium Enterprises (MSMEs) in Indonesia as many as 58.97 million people. It is predicted that the number of MSMEs players in 2019 will amount to 59.2 million. This shows that the Indonesian people have made changes in the field of family economics which initially as consumptive are now productive. The community prefers to carry out activities that can increase family income. Future MSMEs remain the mainstay of the national economy. In accordance with the government roadmap, in 2020 e-commerce transactions are predicted to reach Rp1,300 trillion or equivalent to USD130 billion. According to data from the Central Statistics Agency (BPS), the contribution of MSMEs to Indonesia's Gross Domestic Product (GDP) reached 61.41%, with the number of MSMEs reaching almost 60 million units. However, only around 8% or 3.79 million of the 59.2 million MSMEs players have used online platforms to market their products. Based on the above problems, researchers conducted research on the analysis and display of E-Marketplace for MSMEs in Indonesia. The type of research used is action research. The object of research is MSMEs which are under the Office of Industry and Trade of Sragen Regency. The method of data collection is by techniques: (1) interview, (2) documentation (3) observation, (4) literature study. The researcher uses the waterfall method in developing the system. The research team has successfully analyzed the E-Market place according to the results of data collection. The research team has succeeded in designing the E-Marketplace for MSMEs. E-Marketplace designed can be used by admin, MSME and user. Admin is in charge of managing E-Marketplace and has full access rights. MSMEs can register online and manage their products in E-Marketplace. Users or buyers can search data in E-Marketplace as desired. To make transactions, users can interact directly with MSMEs according to the data provided in E-Marketplace. E-Marketplace can be used for marketing together MSMEs products. This e-marketplace can be accessed at www.umkmonline.com
REMOTE SENSING AND GEOGRAPHIC INFORMATION SYSTEMS AM Publications
Remote sensing technology's increasing accessibility helps us observe research and learn about our globe in ways we could only imagine a generation ago. Guides to profound knowledge of historical, conceptual and practical uses of remote sensing which is increasing GIS technology. This paper will go briefly through remote sensing benefits, history, technology and the GIS and remote sensing integration and their applications. Remote sensing (RS) is used in mapping the predicted and actual species and dominates the ecosystem canopy.
EVALUATE THE STRAIN ENERGY ERROR FOR THE LASER WELD BY THE H-REFINEMENT OF TH...AM Publications
Currently, the finite element method (FEM) is still one of the useful tools in numerical simulation for technical problems. With this method, a continuum model presented by a certain number of elements with a simple approximation field causes the presence of discretization error in solutions. This paper considers the butt weld by laser which subjected the tension for AISI 1018 steel highness 8 mm. The aim of the study is to use the h-refinement of the FEM in estimation the strain energy error for the laser weld mentioned. The results show that the stability of the h-refinement shown by the value of the relative error of the strain energy is quite small, specifically; FEM is less than 5.7% and extra is no more than 3.7%.
HMM APPLICATION IN ISOLATED WORD SPEECH RECOGNITIONAM Publications
Speech recognition is always being an all-time trendy topic for discussion and also for researches and we see a major application in our life. This paper provides the work done on the application of Hidden Markov model to implement isolated word speech recognition on MATLAB and to develop and train the system for set of self-selective words for specific user (user dependent) to get maximum efficiency in word recognition system. Which uses the forward and Baum-welch algorithm and fitting Gaussian of the Baum-welch algorithm for all the iteration perform. We use a sample of 7 alphabets which are recorded in 15 different ways giving total of 105 word to use for training with each word with 15 variations. This system can be used in real world in system security using voice security system and mainly for children and impaired people.
PEDESTRIAN DETECTION IN LOW RESOLUTION VIDEOS USING A MULTI-FRAME HOG-BASED D...AM Publications
Detecting pedestrians in low resolution videos is a challenging task, due to the small size of pedestrians in the images and the limited information. In practical outdoor surveillance scenarios the pedestrian size is usually small. Existing state-of-the-art pedestrian detection methods that use histogram of oriented gradient (HOG) features have poor performance in this problem domain. To compensate for the lack of information in a single frame, we propose a novel detection method that recognizes pedestrians in a short sequence of frames. Namely, we take the single-frame HOG-based detector and extend it to multiple frames. Our detector is applied to regions containing potential moving objects. In the case of video taken from a moving camera on an aerial platform, video stabilization is first performed to register the frames. A classifier is then applied to features extracted from spatio-temporal volumes surrounding the potential moving objects. On challenging stationary and aerial video datasets, our detection accuracy outperforms several state-of-the-art algorithms.
The aim of this paper is to help the blind people to identify and catch the public transport vehicles with the help of Light Fidelity technology. It is a Navigation aid. When the bus arrives at the bus stand, transmitter in the bus transmits the light signals and receiver in the stick, receives the light signals and a sound signal is generated through the speaker present in the stick. The sound message contains the bus number and the destination of the bus. In addition to this, if the person is absconded or lost, details of the location will be sent to his/her family members by pressing a button. This is made possible with the help of Global System for Mobile (GSM). Finally, presence of water can be detected along the blind person’s path, with the help of water sensors.
EFFECT OF SILICON - RUBBER (SR) SHEETS AS AN ALTERNATIVE FILTER ON HIGH AND L...AM Publications
A digital radiography delivers a radiation dose to patients; therefore it poses potential risk to the patients. One effort to reduce dose is carried out using a radiation filter, e.g. Silicone Rubber (SR) sheet. The purpose of this research was to determine the impact of the SR sheet on the high contrast objects (HCO) and the low contrast objects (LCO). The dose reduction was determined from attenuation x-rays before and after using the SR sheet. Assessment of HCO and LCO was observed from CDR TOR phantom at tube voltage of 48 kVp and tube current of 8 mAs. The physical parameter to assess image quality was the Signal to Noise Ratio (SNR) value in LCO. The maximum x-ray attenuation using the SR sheet is 48.82%. The visibility of the HCO remains the same, namely 16 objects; however the LCO slighly decreases from 14 objects to 13 objects after using the SR sheet. The SNR value decreases with an average value of 15.17%.Therefore, the SR sheet as a alternative filter has no effect on the HCO and has realtively little effect on the LCO. Thus, the SR sheet potentially is used for radiation protection in patients, especially on examinations that do not require low contrast resolution.
UTILIZATION OF IMMUNIZATION SERVICES AMONG CHILDREN UNDER FIVE YEARS OF AGE I...AM Publications
Immunization is the key strategy to curb communicable diseases which are the number one killer of children under five. Immunization prevents mortalities of approximating three million children under five annually. This study aimed to assess utilization of immunization services among children under five of age in Kirinyaga County, Kenya.
REPRESENTATION OF THE BLOCK DATA ENCRYPTION ALGORITHM IN AN ANALYTICAL FORM F...AM Publications
The article presents the study of cryptographic transformations of the Kuznyechik algorithm in relation to differential analysis and the translation of their representations into a more convenient form for cryptanalysis. A simplification of the type of transformations of the algorithm to algebraic the form, in which cryptanalysis software will be more effective. Since the description of the algorithm in the analytical form allows for 16 cycles of execution of the shift register with linear feedback, each of which will be carried out 16 operations of multiplication and 15 operations of addition, reduced to 16 multiplying and 15 the operations of addition. The result is an algebraic form of a linear transformation (from a shift register with linear feedback to the multiplication of the matrix in a finite field). In the future, the algebraic type of transformation can be used to effectively carry out differential cryptanalysis.
Optical character recognition (OCR) is process of classification of optical patterns contained in a digital image. The process of OCR Recognition involves several steps including pre-processing, segmentation, feature extraction, classification. Pre-processing is for done the basic operation on input image like noise reduction which remove the noisy signal from image. Segmentation stage for segment the given image into line by line and segment each character from segmented line. Future extraction calculates the characteristics of character. A Radial Basis Function Neural Network (RBFNN) is used to classification contains the database and does the comparison.
Surveillance refers to the task of observing a scene, often for lengthy periods in search of particular objects or particular behaviour. This task has many applications, foremost among them is security (monitoring for undesirable behaviour such as theft or vandalism), but increasing numbers of others in areas such as agriculture also exist. Historically, closed circuit TV (CCTV) surveillance has been mundane and labour Intensive, involving personnel scanning multiple screens, but the advent of reasonably priced fast hardware means that automatic surveillance is becoming a realistic task to attempt in real time. Several attempts at this are underway.
SIMULATION OF ATMOSPHERIC POLLUTANTS DISPERSION IN AN URBAN ENVIRONMENTAM Publications
Interest in air pollution investigation of urban environment due to existence of industrial and commercial activities along with vehicular emission and existence of buildings and streets which setup natural barrier for pollutant dispersion in the urban environment has increased. The air pollution modelling is a multidisciplinary subject when the entire cities are taken under consideration where urban planning and geometries are complex which needs a large software packages to be developed like Operational Street Pollution Model (OSPM), California Line Source model (CALINE series) etc. On overviewing various works it can be summarized that the air pollutant dispersion in urban street canyons and all linked phenomenon such as wind flow, pollutant concentrations, temperature distribution etc. generally depend on wind speed and direction, building heights and density, road width, source and intensity of air pollution, meteorological variables like temperature, humidity etc. A unique and surprising case is observed every time on numerous combinations of these factors. The main aim of this study is to simulate the atmospheric pollutant dispersion for given pollutant like carbon monoxide, sulphur dioxide and nitrogen dioxide and given atmospheric conditions like wind speed and direction. Computational Fluid Dynamics (CFD) simulation for analysing the atmospheric pollutant dispersion is done after natural airflow analysis. Volume rendering is done for variables such as phase 2 volume fraction and velocity with resolution as 250 pixels per inch and transparency as 20%. It can be observed that all the three pollutant namely nitrogen dioxide, sulphur dioxide and carbon monoxide the phase 2 volume fraction changes from 0 to 1. The wind velocity changes from 3.395×10-13 m/s to 1.692×102 m/s. The dispersion of pollutants follow the sequence Sulphur dioxide>Carbon monoxide>Nitrogen dioxide.
PREPARATION AND EVALUATION OF WOOL KERATIN BASED CHITOSAN NANOFIBERS FOR AIR ...AM Publications
In this article, we have extracted keratin from deccani wool waste and prepared the wool keratin based Chitosan nanofibers by electrospinning technique. The prepared nanofibers mat were prepared with different weight percent ratio like 1wt.%, 3wt.% and 5wt.% with respect to polymer i.e Chitosan. The physicochemical and filtration properties of wool keratin based Chitosan nanofibers were studied. Wool keratin based Chitosan nanofibers were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), differential scanning calorimetry (DSC) and scanning electron microscopy (FESEM). The filtration efficiency of keratin Chitosan nanofibers were investigated through DOP test and heavy metal removal capacity of evaluated through Atomic absorption spectroscopy. FTIR results were showed that Keratin gets compatible with Chitosan. XRD patterns revealed keratin was in crystalline nature and increase the crystalline nature of Chitosan nanofibers. FESEM images showed that uniform nanofibers generation with average fiber diameter 80nm. Nanofibers filtration efficiency against a particulate matter in air was obtained more than 99.53% and excellent property of removal of heavy metal.
ANALYSIS ON LOAD BALANCING ALGORITHMS IMPLEMENTATION ON CLOUD COMPUTING ENVIR...AM Publications
Cloud computing means storing and accessing data and programs over the Internet instead of your computer's hard drive. The cloud is just a metaphor for the Internet. The elements involved in cloud computing are clients, data center and distributed server. One of the main problems in cloud computing is load balancing. Balancing the load means to distribute the workload among several nodes evenly so that no single node will be overloaded. Load can be of any type that is it can be CPU load, memory capacity or network load. In this paper we presented an architecture of load balancing and algorithm which will further improve the load balancing problem by minimizing the response time. In this paper, we have proposed the enhanced version of existing regulated load balancing approach for cloud computing by comping the Randomization and greedy load balancing algorithm. To check the performance of proposed approach, we have used the cloud analyst simulator (Cloud Analyst). Through simulation analysis, it has been found that proposed improved version of regulated load balancing approach has shown better performance in terms of cost, response time and data processing time.
A MODEL BASED APPROACH FOR IMPLEMENTING WLAN SECURITY AM Publications
This paper presents various security features and configurations commonly implemented in WLANs and their aggregated security levels and then proposes a model that enables implementation and evaluation of WLAN security
When listening about building new Ventures, Marketplaces ideas are something very frequent. On this session we will discuss reasons why you should stay away from it :P , by sharing real stories and misconceptions around them. If you still insist to go for it however, you will at least get an idea of the important and critical strategies to optimize for success like Product, Business Development & Marketing, Operations :)
Reflect Festival Limassol May 2024.
Michael Economou is an Entrepreneur, with Business & Technology foundations and a passion for Innovation. He is working with his team to launch a new venture – Exyde, an AI powered booking platform for Activities & Experiences, aspiring to revolutionize the way we travel and experience the world. Michael has extensive entrepreneurial experience as the co-founder of Ideas2life, AtYourService as well as Foody, an online delivery platform and one of the most prominent ventures in Cyprus’ digital landscape, acquired by Delivery Hero group in 2019. This journey & experience marks a vast expertise in building and scaling marketplaces, enhancing everyday life through technology and making meaningful impact on local communities, which is what Michael and his team are pursuing doing once more with Exyde www.goExyde.com
Salma Karina Hayat is Conscious Digital Transformation Leader at Kudos | Empowering SMEs via CRM & Digital Automation | Award-Winning Entrepreneur & Philanthropist | Education & Homelessness Advocate
What You're Going to Learn
- How These 4 Leaks Force You To Work Longer And Harder in order to grow your income… improve just one of these and the impact could be life changing.
- How to SHUT DOWN the revolving door of Income Stagnation… you know, where new sales come into your magazine while at the same time existing sponsors exit.
- How to transform your magazine business by fixing the 4 “DON’Ts”...
#1 LEADS Don’t Book
#2 PROSPECTS Don’t Show
#3 PROSPECTS Don’t Buy
#4 CLIENTS Don’t Stay
- How to identify which leak to fix first so you get the biggest bang for your income.
- Get actionable strategies you can use right away to improve your bookings, sales and retention.
Textile Chemical Brochure - Tradeasia (1).pdfjeffmilton96
Explore Tradeasia’s brochure for eco-friendly textile chemicals. Enhance your textile production with high-quality, sustainable solutions for superior fabric quality.
Best Crypto Marketing Ideas to Lead Your Project to SuccessIntelisync
In this comprehensive slideshow presentation, we delve into the intricacies of crypto marketing, offering invaluable insights and strategies to propel your project to success in the dynamic cryptocurrency landscape. From understanding market trends to building a robust brand identity, engaging with influencers, and analyzing performance metrics, we cover all aspects essential for effective marketing in the crypto space.
Also Intelisync, our cutting-edge service designed to streamline and optimize your marketing efforts, leveraging data-driven insights and innovative strategies to drive growth and visibility for your project.
With a data-driven approach, transparent communication, and a commitment to excellence, InteliSync is your trusted partner for driving meaningful impact in the fast-paced world of Web3. Contact us today to learn more and embark on a journey to crypto marketing mastery!
Ready to elevate your Web3 project to new heights? Contact InteliSync now and unleash the full potential of your crypto venture!