This study determined using divergence measures the best indivi- dual and combinations of various numbers of bands for six land cover/use classes around the city of Arequipa, Peru. A 15 band data stack consisting of PALSAR L-band dual-polarised radar, Landsat optical data, as well as six variance texture measures extracted from the PALSAR images, was used in this study. Spectral signatures were obtained for each class for the diver- gence examination. The band having the highest separability was the Landsat visible red band followed by the two largest window PALSAR texture measures. The best three band combina- tion included three very different data types, Landsat visible red, near infrared and the PALSAR HH variance texture from a 17 × 17 pixel window. There was no need based upon the diver- gence values to use more than five bands for classification.
An evaluation of Radarsat-2 individual and combined image dates for land use/...rsmahabir
Various land use/cover types exhibit seasonal characteristics which can be captured in remotely sensed imagery. This study examined how different seasons of Radarsat-2 data influence land use/cover classification accuracies for two study sites. Two dates of Radarsat-2 C-band quad-polarized images were obtained for Washington, D.C., USA and Wad Madani, Sudan. Spectral signatures were extracted and used with a maximum likelihood decision rule for classification and thematic accuracies were then determined. Both despeckled radar and derived texture measures were examined. Thematic accuracies for the two despeckled image dates were similar with a difference of 3% for Washington and 6% for Sudan. Merging the despeckled images for both seasons increased overall accuracy by 2% for Washington and 9% for Sudan. Further combining the original radar for both seasons with derived texture measures increased overall accuracies by 9% for Washington and 16% for Sudan for final overall accuracy values of 73% and 82%.
Radar and optical remote sensing data evaluation and fusion; a case study for...rsmahabir
The recent increase in the availability of spaceborne radar in different wavelengths with multiple polarisations provides new opportunities for land surface analysis. This research effort explored how different radar data, and derived texture values, indepen- dently and in combination with optical imagery influence land cover/use classification accuracies for a study site in Washington, DC, USA. Two spaceborne radar images, Radarsat-2L-band and Palsar C-band quad-polarised radar, were registered with Aster optical data for this study. Traditional methods of classification were applied to various components and combinations of this data set, and overall and class-specific thematic accuracies obtained for comparison. The results for the two despeckled radar data sets were quite different, with Radarsat-2 obtaining an overall accuracy of 59% and Palsar 77%, while that of the optical Aster was 90%. Combining the original radar and a variance texture measure increased the accuracy of Radarsat-2 to 71% but that of Palsar only to 78%. One of the sensor fusions of optical and radar obtained an accuracy of 93%. For this location, radar by itself does not obtain classification accuracies as high as optical data, but fusion with optical imagery provides better overall thematic accuracy than the optical independently, and results in some useful improvements on a class-by-class basis. For those regions with high cloud cover, quad polarisation radar can independently provide viable results but it may be wavelength-dependent.
Separability Analysis of Integrated Spaceborne Radar and Optical Data: Sudan ...rsmahabir
Abstract-The purpose of this study was to determine via spectral separability using divergence measures the best individual and combinations of various numbers of bands for five land cover/ land use classes along the Blue Nile in Sudan. The data for this analysis were a stack of 15 layers including RADARSAT-2 C-band and PALSAR L-band quad-polarized radar registered with ASTER optical data, as well as four variance texture measures extracted from the RADARSAT-2 images. Spectral signatures were obtained for each class and examined by various separability measures. This examination is useful for better understanding the relative value of different types of remote sensing data and best band combinations for possible visual analysis and for improving land cover/ land use classification accuracy. Results show that the best single band for analysis was the RADARSAT-2 VH variance texture measure. The best pair of bands was the ASTER visible red and the RADARSAT-2 HV variance texture, which also included the PALSAR VH band for the best three band combination, all bands being very different data types. Further, based upon the divergence values, only eight bands are needed to achieve maximum separation between land cover/ land use classes. Beyond this point, classification accuracy is expected to decrease, with as few as six bands needed to reach viable classification accuracy.
Comparison and integration of spaceborne optical and radar data for mapping i...rsmahabir
The purpose of this study was to determine how different procedures and data, such as multiple wavelengths of radar imagery and radar texture measures, independently and in combination with optical imagery influence land-cover/use classification accuracies for a study site in Sudan. Radarsat-2 C-band and phased array L-band synthetic aperture radar (PALSAR) L-band quad-polarized radar were registered with ASTER (Advanced Spaceborne Thermal Emission and Reflection Radiometer) optical data. Spectral signatures were obtained for multiple landscape features, classified using a maximum-likelihood decision rule, and thematic accuracies were obtained using sepa- rate validation data. There were surprising differences between the thematic accuracies of the two radar data sets, with Radarsat-2 only having a 51% accuracy and PALSAR 73%. In contrast, the optical ASTER overall accuracy was 81%. Combining the original radar and a variance texture measure increased the Radarsat-2 to 78% and PALSAR to 80%, whereas the two original radar bands together had an accuracy of 87%. Sensor fusion of optical and radar obtained an accuracy of 93%. Based on these results, the use of multiwavelength quad-polarized radar imagery combined or inte- grated with optical imagery has great potential in improving the accuracy of land- cover/use classifications. In tropical and high-latitude regions of the world, where persistent cloud cover hinders the use of optical satellite systems, land management programmes may find this research promising.
An evaluation of Radarsat-2 individual and combined image dates for land use/...rsmahabir
Various land use/cover types exhibit seasonal characteristics which can be captured in remotely sensed imagery. This study examined how different seasons of Radarsat-2 data influence land use/cover classification accuracies for two study sites. Two dates of Radarsat-2 C-band quad-polarized images were obtained for Washington, D.C., USA and Wad Madani, Sudan. Spectral signatures were extracted and used with a maximum likelihood decision rule for classification and thematic accuracies were then determined. Both despeckled radar and derived texture measures were examined. Thematic accuracies for the two despeckled image dates were similar with a difference of 3% for Washington and 6% for Sudan. Merging the despeckled images for both seasons increased overall accuracy by 2% for Washington and 9% for Sudan. Further combining the original radar for both seasons with derived texture measures increased overall accuracies by 9% for Washington and 16% for Sudan for final overall accuracy values of 73% and 82%.
Radar and optical remote sensing data evaluation and fusion; a case study for...rsmahabir
The recent increase in the availability of spaceborne radar in different wavelengths with multiple polarisations provides new opportunities for land surface analysis. This research effort explored how different radar data, and derived texture values, indepen- dently and in combination with optical imagery influence land cover/use classification accuracies for a study site in Washington, DC, USA. Two spaceborne radar images, Radarsat-2L-band and Palsar C-band quad-polarised radar, were registered with Aster optical data for this study. Traditional methods of classification were applied to various components and combinations of this data set, and overall and class-specific thematic accuracies obtained for comparison. The results for the two despeckled radar data sets were quite different, with Radarsat-2 obtaining an overall accuracy of 59% and Palsar 77%, while that of the optical Aster was 90%. Combining the original radar and a variance texture measure increased the accuracy of Radarsat-2 to 71% but that of Palsar only to 78%. One of the sensor fusions of optical and radar obtained an accuracy of 93%. For this location, radar by itself does not obtain classification accuracies as high as optical data, but fusion with optical imagery provides better overall thematic accuracy than the optical independently, and results in some useful improvements on a class-by-class basis. For those regions with high cloud cover, quad polarisation radar can independently provide viable results but it may be wavelength-dependent.
Separability Analysis of Integrated Spaceborne Radar and Optical Data: Sudan ...rsmahabir
Abstract-The purpose of this study was to determine via spectral separability using divergence measures the best individual and combinations of various numbers of bands for five land cover/ land use classes along the Blue Nile in Sudan. The data for this analysis were a stack of 15 layers including RADARSAT-2 C-band and PALSAR L-band quad-polarized radar registered with ASTER optical data, as well as four variance texture measures extracted from the RADARSAT-2 images. Spectral signatures were obtained for each class and examined by various separability measures. This examination is useful for better understanding the relative value of different types of remote sensing data and best band combinations for possible visual analysis and for improving land cover/ land use classification accuracy. Results show that the best single band for analysis was the RADARSAT-2 VH variance texture measure. The best pair of bands was the ASTER visible red and the RADARSAT-2 HV variance texture, which also included the PALSAR VH band for the best three band combination, all bands being very different data types. Further, based upon the divergence values, only eight bands are needed to achieve maximum separation between land cover/ land use classes. Beyond this point, classification accuracy is expected to decrease, with as few as six bands needed to reach viable classification accuracy.
Comparison and integration of spaceborne optical and radar data for mapping i...rsmahabir
The purpose of this study was to determine how different procedures and data, such as multiple wavelengths of radar imagery and radar texture measures, independently and in combination with optical imagery influence land-cover/use classification accuracies for a study site in Sudan. Radarsat-2 C-band and phased array L-band synthetic aperture radar (PALSAR) L-band quad-polarized radar were registered with ASTER (Advanced Spaceborne Thermal Emission and Reflection Radiometer) optical data. Spectral signatures were obtained for multiple landscape features, classified using a maximum-likelihood decision rule, and thematic accuracies were obtained using sepa- rate validation data. There were surprising differences between the thematic accuracies of the two radar data sets, with Radarsat-2 only having a 51% accuracy and PALSAR 73%. In contrast, the optical ASTER overall accuracy was 81%. Combining the original radar and a variance texture measure increased the Radarsat-2 to 78% and PALSAR to 80%, whereas the two original radar bands together had an accuracy of 87%. Sensor fusion of optical and radar obtained an accuracy of 93%. Based on these results, the use of multiwavelength quad-polarized radar imagery combined or inte- grated with optical imagery has great potential in improving the accuracy of land- cover/use classifications. In tropical and high-latitude regions of the world, where persistent cloud cover hinders the use of optical satellite systems, land management programmes may find this research promising.
Drones in the Earth Sciences - Opportunities and issuesARDC
Tim Rawling – AuScope, our vision and the National Research Infrastructure investment landscape
Steven Micklethwaite – Opportunity for application of drones in the Earth Sciences, technology and issues
Geovisualisation of flows: New approaches to map an interdependent worldBenjamin Hennig
Postgraduate Presentation by Benjamin D Hennig at the Department of Geography, University of Sheffield, 26th May 2009 - more at http://www.viewsoftheworld.net/?p=2777
Artificial Intelligence and Big Data Techniques for Copernicus Data: the ExtremeEarth project
Manolis Koubarakis (Professor at the National and Kapodistrian University of Athens and Adjunct Researcher at the Institute of the Management of Information Systems)
Radar speckle reduction and derived texture measures for land cover/use class...rsmahabir
This study examined the appropriateness of radar speckle reduction for deriving texture measures for land cover/use classifications. Radarsat-2 C-band quad-polarized data were obtained for Washington, D.C., USA. Polarization signatures were extracted for multiple image components, classified with a maximum-likelihood decision rule and thematic accuracies determined. Initial classifications using original and despeckled scenes showed despeckled radar to have better overall thematic accuracies. However, when variance texture measures were extracted for several window sizes from the original and despeckled imagery and classified, the accuracy for the radar data was decreased when despeckled prior to texture extraction. The highest classification accuracy obtained for the extracted variance texture measure from the original radar was 72%, which was reduced to 69% when this measure was extracted from a 5x5 despeckled image. These results suggest that it may be better to use despeckled radar as original data and extract texture measures from the original imagery.
Drones in the Earth Sciences - Opportunities and issuesARDC
Tim Rawling – AuScope, our vision and the National Research Infrastructure investment landscape
Steven Micklethwaite – Opportunity for application of drones in the Earth Sciences, technology and issues
Geovisualisation of flows: New approaches to map an interdependent worldBenjamin Hennig
Postgraduate Presentation by Benjamin D Hennig at the Department of Geography, University of Sheffield, 26th May 2009 - more at http://www.viewsoftheworld.net/?p=2777
Artificial Intelligence and Big Data Techniques for Copernicus Data: the ExtremeEarth project
Manolis Koubarakis (Professor at the National and Kapodistrian University of Athens and Adjunct Researcher at the Institute of the Management of Information Systems)
Radar speckle reduction and derived texture measures for land cover/use class...rsmahabir
This study examined the appropriateness of radar speckle reduction for deriving texture measures for land cover/use classifications. Radarsat-2 C-band quad-polarized data were obtained for Washington, D.C., USA. Polarization signatures were extracted for multiple image components, classified with a maximum-likelihood decision rule and thematic accuracies determined. Initial classifications using original and despeckled scenes showed despeckled radar to have better overall thematic accuracies. However, when variance texture measures were extracted for several window sizes from the original and despeckled imagery and classified, the accuracy for the radar data was decreased when despeckled prior to texture extraction. The highest classification accuracy obtained for the extracted variance texture measure from the original radar was 72%, which was reduced to 69% when this measure was extracted from a 5x5 despeckled image. These results suggest that it may be better to use despeckled radar as original data and extract texture measures from the original imagery.
Land Use/Land Cover Mapping Of Allahabad City by Using Remote Sensing & GIS IJMER
The present study was carried out to produce and evaluate the land use/land cover maps by on
screen visual interpretation. The studies of land cover of Allahabad city (study area) consist of 87517.47 ha
out of which 5500.35 ha is build up land (Urban / Rural) Area. In this respect, the Build up land (Urban /
Rural) area scorers 6.28% of the total area. It has also been found that about 17155.001ha (19.60 %) of
area is covered by current fallow land. The double/triple crop land of 30178.44ha (34.84%). The area
covered by gullied / ravines is 1539.20 ha (1.75 %) and that of the kharif crop land is 2828.00 ha (3.23 %).
The area covered by other wasteland is 2551.05ha (2.91%). Table 4.1 shows the area distribution of the
various land use and land cover of Allahabad city.
Effectiveness and Capability of Remote Sensing (RS) and Geographic Informatio...nitinrane33
In this research paper, the effectiveness and capability of remote sensing (RS) and geographic information systems (GIS) are investigated as powerful tools for analyzing changes in land use and land cover (LULC), as well as for accuracy assessment. The study employs the literature of satellite imagery and GIS data to evaluate LULC changes over a period and to assess the accuracy of the analysis. Moreover, the research investigates the land use and land cover change detection analysis using RS and GIS, application of artificial intelligence (AI), and Machine Learning (ML) in LULC classification, environment and risk evaluation, stages of process LULC classification, factors affecting the LULC classification, accuracy assessment, and potential applications of RS and GIS in predicting future LULC changes and supporting decision-making processes. The findings of the study suggest that RS and GIS are highly effective and accurate for LULC analysis and assessment, with substantial potential for predicting and managing future changes in land use and land cover. The paper emphasizes the importance of utilizing RS and GIS techniques in the field of sustainable environmental management and resource planning.
Predictive geospatial analytics using principal component regression IJECEIAES
Nowadays, exponential growth in geospatial or spatial data all over the globe, geospatial data analytics is absolutely deserved to pay attention in manipulating voluminous amount of geodata in various forms increasing with high velocity. In addition, dimensionality reduction has been playing a key role in high-dimensional big data sets including spatial data sets which are continuously growing not only in observations but also in features or dimensions. In this paper, predictive analytics on geospatial big data using Principal Component Regression (PCR), traditional Multiple Linear Regression (MLR) model improved with Principal Component Analysis (PCA), is implemented on distributed, parallel big data processing platform. The main objective of the system is to improve the predictive power of MLR model combined with PCA which reduces insignificant and irrelevant variables or dimensions of that model. Moreover, it is contributed to present how data mining and machine learning approaches can be efficiently utilized in predictive geospatial data analytics. For experimentation, OpenStreetMap (OSM) data is applied to develop a one-way road prediction for city Yangon, Myanmar. Experimental results show that hybrid approach of PCA and MLR can be efficiently utilized not only in road prediction using OSM data but also in improvement of traditional MLR model.
INTEGRATION OF REMOTE SENSING DATA WITH GEOGRAPHIC INFORMATION SYSTEM (GIS): ...ijmpict
Remote Sensing and Geographic information System together comprise of Geographic Information Science (GIScience) which is a core research field that tries to emphasis on advanced geographic concepts in Geographic Information System and examines the impact of GIS on individuals and society as a whole and re-examines the themes with incorporation of most recent cognitive and Information Science. The Geographic Information System can be defined as a Computer based system and a tool, both hardware,
software and procedures, which manages geospatial data, solves spatial problems, and supports collection,
storage, transformation, analyzing, retrieving and display of data in a well desired manner. The integration
of GIS and Remote Sensing is a field of research and several implementations have been developed to gain
the maximum throughput out of these collective fields as these techniques have their own data analysis and
data representation methods. The application domain of remote sensing is from a base layer for GIS to the
development of thematic datasets, obtaining and extracting data from imagery and generation of unique
spatial datasets. In my paper I have focused on the integration of both the fields along with its usage in
Analysis and Modelling and also some models of error sources due to the integration of interface of the two
techniques. The paper also describes some error sources while integration as GIS and remote sensing both
are subject to errors and uncertainty. The paper has discussed some Change Detection Techniques used in
the modern sciences with their comparison.
REMOTE SENSING AND GEOGRAPHIC INFORMATION SYSTEMS AM Publications
Remote sensing technology's increasing accessibility helps us observe research and learn about our globe in ways we could only imagine a generation ago. Guides to profound knowledge of historical, conceptual and practical uses of remote sensing which is increasing GIS technology. This paper will go briefly through remote sensing benefits, history, technology and the GIS and remote sensing integration and their applications. Remote sensing (RS) is used in mapping the predicted and actual species and dominates the ecosystem canopy.
Future Development of NSDI Based on the European INSPIRE Directive – a Case S...Maksim Sestic
(...) Without spatial data and services, it would be impossible to manage space effectively, plan city development, monitor the situation on the ground, or carry out many other activities. This paper gives an overview of different initiatives and efforts in establishing SDI in Bosnia and Herzegovina. State bodies such as the government and the State Geodetic Administration have the main role in collaborating with the public and commercial sectors and also with the academic community. As the main factor in creating a future SDI, the State Geodetic Administration has launched several initiatives the goal of which is the installation of new technologies, equipment and procedures in map production and the establishment of digital topographic and cadastre databases. In the next few years Bosnia and Herzegovina must accomplish numerous tasks to arrange spatial records. These tasks must be accomplished very conscientiously and in a reasonable period of time. It is very important for Bosnia and Herzegovina’s prosperity and for the fulfillment of the conditions established for the process of entering European and international integrations. (...)
Need for Pan India Compatibility of Geospatial Databases in Terms of Map Proj...Mallikarjun Mishra
The present study is taken up to record variations in the extent of area of two polygons–(i)a ground measured area of a university campus, (ii)enclosing the Ganga basin and a polygon covering (iii)India to examine the changes in both shape and area–under different map projections with various parameters. The exercise brought forth interesting results. Depending on final ranks worked out based on minimum differences in extent of areas and shape distortion in the case of India, it is suggested to adopt either (i)LCC projection with Everest India-Nepal datum, First Standard Parallel (FSP) 24.50, Second Standard Parallel (SSP) 28.50, Latitude of Origin (LO) 16.253259, Central Meridian (CM) 80.8749 or (ii)LCC projection with WGS 84 datum, FSP 24.50, SSP 28.50, LO 16.253259, CM 80.8749 or (iii)Polyconic with Everest India-Nepal datum, CM 84.50, LO 13.00, for mapping both smaller areas on larger scales and larger areas on smaller scales.
Similar to Relative value of radar and optical data for land cover/use mapping: Peru example (20)
A Critical Review of High and Very High-Resolution Remote Sensing Approaches ...rsmahabir
Slums are a global urban challenge, with less developed countries being particularly impacted. To adequately detect and map them, data is needed on their location, spatial extent and evolution. High- and very high-resolution remote sensing imagery has emerged as an important source of data in this regard. The purpose of this paper is to critically review studies that have used such data to detect and map slums. Our analysis shows that while such studies have been increasing over time, they tend to be concentrated to a few geographical areas and often focus on the use of a single approach (e.g., image texture and object-based image analysis), thus limiting generalizability to understand slums, their population, and evolution within the global context. We argue that to develop a more comprehensive framework that can be used to detect and map slums, other emerging sourcing of geospatial data should be considered (e.g., volunteer geographic information) in conjunction with growing trends and advancements in technology (e.g., geosensor networks). Through such data integration and analysis we can then create a benchmark for determining the most suitable methods for mapping slums in a given locality, thus fostering the creation of new approaches to address this challenge.
Impact of road networks on the distribution of dengue fever cases in Trinidad...rsmahabir
This study examined the impact of road networks on the distribution of dengue fever cases in Trinidad, West Indies. All confirmed cases of dengue hemorrhagic fever (DHF) observed during 1998 were georef- erenced and spatially located on a road map of Trinidad using Geographic Information Systems software. A new digital geographic layer representing these cases was created and the distances from these cases to the nearest classified road category (5 classifications based on a functional utility system) were examined. The distance from each spatially located DHF case to the nearest road in each of the 5 road subsets was determined and then subjected to an ANOVA and t-test to determine levels of association between minor road networks (especially 3rd and 4th class roads) and DHF cases and found DHF cases were located away from forests, especially 5th class roads). The frequency of DHF cases to different road classes was: 0% (1st class roads), 7% (2nd class roads), 32% (3rd class roads), 57% (4th class roads) and 4% (5th class road). The data clearly demonstrated that both class 3 and class 4 roads account for 89% of nearby dengue cases. These results represent the first evidence of dengue cases being found restricted between forested areas and major highways and would be useful when planning and implementing control strategies for dengue and Aedes aegypti mosquitoes.
The Rabies Epidemic in Trinidad of 1923 to 1937: An Evaluation with a Geograp...rsmahabir
Background.—Rabies, although not preeminent among current infectious diseases, continues to afflict humans with as many as 55,000 deaths annually. The case fatality rate remains the highest among infectious diseases, and medical treatments have proven ineffective.
Objective.—This study analyzes the rabies epidemic of 1929 to 1937 in Trinidad from a geograph- ical perspective, using Geographic Information System (GIS) software as an analytical tool.
Setting.—A small island developing country at a time when infectious diseases were rampant.
Methods.—A review of the literature was undertaken, and data were collected on the occurrence of disease in both animal and humans populations and mapped using GIS software. Several factors identified in the literature were further explored such as land use/land cover, rainfall and magnetic declination.
Results.—The bat rabies epidemic of 1923 to 1937 in Trinidad was migratory and seasonal, shifting to new locations along a definite path. The pattern of spread appears to be spatially linked to land use/land cover. The epidemic continues to present many unexplained peculiarities.
Conclusion.—Despite the fact that this epidemic occurred almost 7 decades ago, the application of new tools available for public health use can create new knowledge and understanding of events. We showed that the spatial of distribution of the disease followed a distinct pathway possible due to the use of electromagnetic capabilities of bats.
The Role of Spatial Data Infrastructure in the Management of Land Degradation...rsmahabir
Abstract
Land degradation involves a wide array of natural and human induced factors affecting the productivity of land. These factors can exist in various non unique and complex combinations of different environmental settings, making detection and monitoring of land degradation an often difficult undertaking. As a result, no universal solution exists to eliminate the problem of land degradation altogether. In order to reduce its rate of encroachment, this phenomenon should be assessed and quantified in order to identify the causes, processes and factors leading to land degradation.
In small tropical and Caribbean islands, there exists a severe shortage of good, reliable and up- to-date information bases for the contributing factors of land degradation. In addition to the limited knowledge about what spatial datasets already exist, there is also no agreed minimum level of quality for datasets and metadata documentation standards. As a result, datasets produced to help in understanding and treating land degradation problems may have unknown or unacceptable levels of uncertainty. This may require re-development of already existing datasets, hence consuming further efforts, financial resources, and time. In critical circumstances where land degradation posses severe threat to the environment and therefore indirectly to humans, the incurred price of a slow or ill informed decision may eventually render the state of land unrecoverable.
It is postulated that Spatial Data Infrastructure (SDI) would present the opportunity for much more strategic and cooperative management of land degradation datasets in Small Tropical Caribbean Islands. It is therefore expected to be a vital tool in the treatment of land degradation, and also to assist in creating a network of critical resources to drive further research in the area. This paper reviews the challenges faced by Small Tropical Caribbean Islands when managing land degradation, with special emphasis on Trinidad, and discusses how SDI can be used to better facilitate land degradation management in these areas.
Advancing the Use of Earth Observation Systems for the Assessment of Sustaina...rsmahabir
Abstract: Decisions made on the use of land in Trinidad and Tobago, with little considerations to environmental impact or physical constraints, have resulted in physical, socio-economic, and environmental problems. As a result of the country’s economic progress, urbanisation and development are fragmenting natural areas and reducing the viability of the environment to support the population. Spatial information is a crucial component in the characterisation and examination of the spatio-temporal dynamics and the consequences of the interaction between human and the environment. This information is of critical importance in the development of models to predict future trends in land cover change and therein, best land use practices to be implemented. However, the lack of data at appropriate scales has made it difficult to accurately examine the land use/cover patterns in the country. This paper argues that the gap in data and information can be managed through the adoption of earth observation technology. Moreover, it reports on the developed methodology, and highlights key results of examining the use of geo-spatial images in addressing sustainability issues associated with development. The developed methodology involves several critical steps in using multi-spectral imagery including cloud and cloud shadow removal, image classification and image fusion. Additionally, a method for improving classification performance using high resolution imagery is discussed. The results demonstrated the accuracy, flexibility and cost-effectiveness of these technologies for mapping the land cover and producing other environmental measures and indicators. Further, these results confirmed the effectiveness of this technology in establishing the necessary baseline and support information for sustainable development in the Caribbean region.
Dengue Fever Epidemiology and Control in the Caribbean: A Status Report (2012)rsmahabir
The epidemiology of Dengue fever in the English speaking Caribbean over the last two decades is reviewed. Dengue cases reported to the World Health Organization, Pan American Health Organization, Caribbean Epidemiology Centre and in recent published papers were collated and analysed to determine the incidence and geographical distribution among the various countries. Dengue fever was observed among most Caribbean countries with various intensities of transmission. During 2010 all four dengue serotypes were found co-circulating within the Caribbean islands with crude fatality rates of 6 in Barbados, 4 in Jamaica, 3 in the Bahamas and 2 in Dominica. Similar numbers of males and females from the 20-39 age group were found with DHF but the 10-19 age group shows a slight increase in disease levels. Overall more males were reported with DF/DHF than females. The results show significant (P<0.002) increases in the number of DF/DHF cases and in Ae. aegypti indices during the rainy season compared to the dry season. Little data is available on the density of the Aedes aegypti population in the Caribbean region, and most information comes from Jamaica and Trinidad and Tobago.
APPLICATIONS OF REMOTE SENSING AND GIS TECHNOLOGIES IN FLOOD RISK MANAGEMENTrsmahabir
Flooding is the most common of all major disasters that regularly affect populations and results in extensive damage to property, infrastructure, natural resources, and even to loss of life. To ensure better outcomes, planning and execution of flood management projects must utilize knowledge on a wide range of factors, most of which are of a spatial nature. Advances in geospatial technologies, specifically remote sensing and Geographic Information Systems (GIS), have enabled the acquisition and analysis of data about the Earth's surface for flood mitigation projects in a faster, more efficient and more accurate manner.
Remote sensing and GIS have emerged as powerful tools to deal with various aspects of flood management in prevention, preparedness and relief management of flood disaster. GIS facilitates integration of spatial and non-spatial data such as rainfall and stream flows, river cross sections and profiles, and river basin characteristics, as well as other information such as historical flood maps, infrastructures, land use, and social and economic data. Such data sets are critical for the in-depth analysis and management of floods.
Remote sensing technologies have great potential in overcoming the information void in the Caribbean region. The observation, mapping, and representation of Earth’s surface have provided effective and timely information for monitoring floods and their effect. The potential of new air- and space-borne imaging technologies for improving hazard evaluation and risk reduction is continually being explored. They are relatively inexpensive and have the ability to provide information on several parameters that are crucial to flood mapping and monitoring.
Healthy Food Accessibility and Obesity: Case Study of Pennsylvania, USArsmahabir
Abstract-Obesity is a continuing challenge for any town, city or country faced with this problem. Being obese increases your risk of physical disorders such as high blood pressure (BP), high blood cholesterol, diabetes, coronary heart disease, stroke, cancer and poor reproductive health. Higher obesity rates also leads to increased economic burden on society. In order to better understand and control obesity rates the in uence of various factors on its prevalence should be investigated. We used Ordinary Least Squares (OLS) and Geographically Weighted Regression (GWR) models to analyze spatial relationships using a combination of socio-economic and physical factor for counties in Pennsylvania (PA), USA for 2010. Our ndings suggest that the rate of obesity is impacted by local spatial variation and its prevalence positively correlated with diabetes, physical inactivity and the distance that a person must travel to get to a healthy food store. Additionally, GWR (AICc = 261.59; r-squared = 0.45) was found to signi cantly improve model tting over OLS (AICc = 299.87; r-squared = 0.34). These results indicate that additional factors, including social, cultural and behavioral, are needed to better explain the distribution of obesity rates across PA.
Exploratory space-time analysis of dengue incidence in trinidad: a retrospect...rsmahabir
The increased geographic spread and intensity of dengue is due to numerous factors including, increased urbanization, human migrations and air travel, flooding and global warming. In the Caribbean, outbreaks continue to occur with hyperendemic occurrence of the disease. This is mainly due to the use of reactive programs and limited resources available to control the disease. Using the island of Trinidad as a case study, we show that higher rates of infection occur in areas with a history of dengue incidence. Also, a general pattern in the movement of dengue cases is found leading up to and transitioning away from an epidemic occurrence, and associated with the locations of transportation hubs. These findings can be used to contain the disease in a more efficient and effective manner. Also, few studies have examined the space and time relationship of dengue incidents at local scales in the Caribbean islands. Other islands can adopt the approach used to better allocate resources and understand the disease. This information can then be used to gain regional perspective and understanding about the spatio-temporal persistence of dengue in the Caribbean.
Remote sensing-derived national land cover land use maps: a comparison for Ma...rsmahabir
Reliable land cover land use (LCLU) information, and change over time, is impor- tant for Green House Gas (GHG) reporting for climate change documentation. Four different organizations have independently created LCLU maps from 2010 satellite imagery for Malawi for GHG reporting. This analysis compares the procedures and results for those four activities. Four different classification methods were employed; traditional visual interpretation, segmentation and visual labelling, digital clustering with visual identification and supervised signature extraction with application of a decision rule followed by analyst editing. One effort did not report classification accuracy and the other three had very similar and excellent overall thematic accura- cies ranging from 85 to 89%. However, despite these high thematic accuracies there were very significant differences in results. National percentages for forest ranged from 18.2 to 28.7% and cropland from 40.5 to 53.7%. These significant differences are concerns for both remote-sensing scientists and decision-makers in Malawi.
VDIS: A System for Morphological Detection and Identification of Vehicles in ...rsmahabir
With the growth of urban centers worldwide, the number of vehicles in and around these areas has also increased. Traffic-related data plays an important role in spatial planning, for example, optimizing road networks and in the estimation or simulation of air and noise pollution. This information is important as it reflects the changes taking place around us. Additionally, data collected can be used for a wide array of applications including law enforcement, fleet management, and supporting other analyses at varying scales. In this paper, we present a method for the detection and identification of vehicles from low altitude, high spatial resolution Red Blue Green (RGB) images, utilizing both object spectra and image morphology. Results show an identification performance upwards of 62% with false positives occurring from the use of images with sun glare and vehicles with similar spectra values.
Climate Change and Forest Management: Adaptation of Geospatial Technologiesrsmahabir
eraction with the environment, has led to increased concerns about the impact of such disruption on major areas of sustainable development. This has resulted in various innovations in technology, policy and forged alliances at regional and international scales in an effort to reduce humans’ impact on climate. Forests provide a suitable option for reducing the net amount of carbon dioxide in the atmosphere by acting as carbon sinks, thereby forming one part of a more complete solution for combating climate change. At the same time, forests are also sensitive to changes in climate, making sustainable forest management a critical component of present and future climate change strategies. This paper examines the contribution of geospatial technologies in supporting sustainable forest management, emphasizing its use in the classification of forests, estimation of their structure, detecting change and modeling of carbon stocks.
Black holes no more the emergence of volunteer geographic informationrsmahabir
More than one billion people currently live in slums, which are growing at unprecedented rates leading to the rise of vulnerable communities. Slums are usually viewed as areas of extreme poverty and neglect and further, their development as an impediment to progress. Although slums exist in all areas of the world, their presence is most noticeable in the less developed countries of the global south. These countries are among the poorest worldwide as suggested by the Human Development Index and the substantial disbursement of and dependence on international aid. With the added burden of having to absorb the majority of projected population growth, further challenges can be expected at these locations if the situation of slum dwellers does not improve.
Coral Reefs: Challenges, Opportunities and Evolutionary Strategies for Surviv...rsmahabir
Coral reefs are one of the most diverse marine ecosystems on Earth. They are renowned hotspots of species biodiversity and provide home to a large array of marine plants and animals. Over the past 100 years, many tropical regions’ sea surface temperatures have increased by almost 1 °C and are currently increasing at about 1–2 °C per century. Corals have very specific thermal thresholds beyond which their temperature sensitive symbiont Zooxanthellae becomes affected and causes corals to bleach. Mass bleaching has already caused significant losses to live coral in many parts of the world. In the Caribbean, the problem of coral bleaching has especially been problematic, with as much as 90% bleaching in some parts of the Caribbean due to thermal anomalies in some instances. This paper looks at the key role that temperature plays in the health and spatial distribution of coral in the Caribbean. The relationship between coral and symbiont is examined along with some evolutionary strategies necessary to ensure the future survival of coral with the changing climate.
Authoritative and Volunteered Geographical Information in a Developing Countr...rsmahabir
Abstract: With volunteered geographic information (VGI) platforms such as OpenStreetMap (OSM) becoming increasingly popular, we are faced with the challenge of assessing the quality of their content, in order to better understand its place relative to the authoritative content of more traditional sources. Until now, studies have focused primarily on developed countries, showing that VGI content can match or even surpass the quality of authoritative sources, with very few studies in developing countries. In this paper, we compare the quality of authoritative (data from the Regional Center for Mapping of Resources for Development (RCMRD)) and non-authoritative (data from OSM and Google’s Map Maker) road data in conjunction with population data in and around Nairobi, Kenya. Results show variability in coverage between all of these datasets. RCMRD provided the most complete, albeit less current, coverage when taking into account the entire study area, while OSM and Map Maker showed a degradation of coverage as one moves from central Nairobi towards rural areas. Furthermore, OSM had higher content density in large slums, surpassing the authoritative datasets at these locations, while Map Maker showed better coverage in rural housing areas. These results suggest a greater need for a more inclusive approach using VGI to supplement gaps in authoritative data in developing nations.
Professional air quality monitoring systems provide immediate, on-site data for analysis, compliance, and decision-making.
Monitor common gases, weather parameters, particulates.
Seminar of U.V. Spectroscopy by SAMIR PANDASAMIR PANDA
Spectroscopy is a branch of science dealing the study of interaction of electromagnetic radiation with matter.
Ultraviolet-visible spectroscopy refers to absorption spectroscopy or reflect spectroscopy in the UV-VIS spectral region.
Ultraviolet-visible spectroscopy is an analytical method that can measure the amount of light received by the analyte.
A brief information about the SCOP protein database used in bioinformatics.
The Structural Classification of Proteins (SCOP) database is a comprehensive and authoritative resource for the structural and evolutionary relationships of proteins. It provides a detailed and curated classification of protein structures, grouping them into families, superfamilies, and folds based on their structural and sequence similarities.
Richard's aventures in two entangled wonderlandsRichard Gill
Since the loophole-free Bell experiments of 2020 and the Nobel prizes in physics of 2022, critics of Bell's work have retreated to the fortress of super-determinism. Now, super-determinism is a derogatory word - it just means "determinism". Palmer, Hance and Hossenfelder argue that quantum mechanics and determinism are not incompatible, using a sophisticated mathematical construction based on a subtle thinning of allowed states and measurements in quantum mechanics, such that what is left appears to make Bell's argument fail, without altering the empirical predictions of quantum mechanics. I think however that it is a smoke screen, and the slogan "lost in math" comes to my mind. I will discuss some other recent disproofs of Bell's theorem using the language of causality based on causal graphs. Causal thinking is also central to law and justice. I will mention surprising connections to my work on serial killer nurse cases, in particular the Dutch case of Lucia de Berk and the current UK case of Lucy Letby.
What is greenhouse gasses and how many gasses are there to affect the Earth.moosaasad1975
What are greenhouse gasses how they affect the earth and its environment what is the future of the environment and earth how the weather and the climate effects.
Multi-source connectivity as the driver of solar wind variability in the heli...Sérgio Sacani
The ambient solar wind that flls the heliosphere originates from multiple
sources in the solar corona and is highly structured. It is often described
as high-speed, relatively homogeneous, plasma streams from coronal
holes and slow-speed, highly variable, streams whose source regions are
under debate. A key goal of ESA/NASA’s Solar Orbiter mission is to identify
solar wind sources and understand what drives the complexity seen in the
heliosphere. By combining magnetic feld modelling and spectroscopic
techniques with high-resolution observations and measurements, we show
that the solar wind variability detected in situ by Solar Orbiter in March
2022 is driven by spatio-temporal changes in the magnetic connectivity to
multiple sources in the solar atmosphere. The magnetic feld footpoints
connected to the spacecraft moved from the boundaries of a coronal hole
to one active region (12961) and then across to another region (12957). This
is refected in the in situ measurements, which show the transition from fast
to highly Alfvénic then to slow solar wind that is disrupted by the arrival of
a coronal mass ejection. Our results describe solar wind variability at 0.5 au
but are applicable to near-Earth observatories.
Deep Behavioral Phenotyping in Systems Neuroscience for Functional Atlasing a...Ana Luísa Pinho
Functional Magnetic Resonance Imaging (fMRI) provides means to characterize brain activations in response to behavior. However, cognitive neuroscience has been limited to group-level effects referring to the performance of specific tasks. To obtain the functional profile of elementary cognitive mechanisms, the combination of brain responses to many tasks is required. Yet, to date, both structural atlases and parcellation-based activations do not fully account for cognitive function and still present several limitations. Further, they do not adapt overall to individual characteristics. In this talk, I will give an account of deep-behavioral phenotyping strategies, namely data-driven methods in large task-fMRI datasets, to optimize functional brain-data collection and improve inference of effects-of-interest related to mental processes. Key to this approach is the employment of fast multi-functional paradigms rich on features that can be well parametrized and, consequently, facilitate the creation of psycho-physiological constructs to be modelled with imaging data. Particular emphasis will be given to music stimuli when studying high-order cognitive mechanisms, due to their ecological nature and quality to enable complex behavior compounded by discrete entities. I will also discuss how deep-behavioral phenotyping and individualized models applied to neuroimaging data can better account for the subject-specific organization of domain-general cognitive systems in the human brain. Finally, the accumulation of functional brain signatures brings the possibility to clarify relationships among tasks and create a univocal link between brain systems and mental functions through: (1) the development of ontologies proposing an organization of cognitive processes; and (2) brain-network taxonomies describing functional specialization. To this end, tools to improve commensurability in cognitive science are necessary, such as public repositories, ontology-based platforms and automated meta-analysis tools. I will thus discuss some brain-atlasing resources currently under development, and their applicability in cognitive as well as clinical neuroscience.
Observation of Io’s Resurfacing via Plume Deposition Using Ground-based Adapt...Sérgio Sacani
Since volcanic activity was first discovered on Io from Voyager images in 1979, changes
on Io’s surface have been monitored from both spacecraft and ground-based telescopes.
Here, we present the highest spatial resolution images of Io ever obtained from a groundbased telescope. These images, acquired by the SHARK-VIS instrument on the Large
Binocular Telescope, show evidence of a major resurfacing event on Io’s trailing hemisphere. When compared to the most recent spacecraft images, the SHARK-VIS images
show that a plume deposit from a powerful eruption at Pillan Patera has covered part
of the long-lived Pele plume deposit. Although this type of resurfacing event may be common on Io, few have been detected due to the rarity of spacecraft visits and the previously low spatial resolution available from Earth-based telescopes. The SHARK-VIS instrument ushers in a new era of high resolution imaging of Io’s surface using adaptive
optics at visible wavelengths.
Earliest Galaxies in the JADES Origins Field: Luminosity Function and Cosmic ...Sérgio Sacani
We characterize the earliest galaxy population in the JADES Origins Field (JOF), the deepest
imaging field observed with JWST. We make use of the ancillary Hubble optical images (5 filters
spanning 0.4−0.9µm) and novel JWST images with 14 filters spanning 0.8−5µm, including 7 mediumband filters, and reaching total exposure times of up to 46 hours per filter. We combine all our data
at > 2.3µm to construct an ultradeep image, reaching as deep as ≈ 31.4 AB mag in the stack and
30.3-31.0 AB mag (5σ, r = 0.1” circular aperture) in individual filters. We measure photometric
redshifts and use robust selection criteria to identify a sample of eight galaxy candidates at redshifts
z = 11.5 − 15. These objects show compact half-light radii of R1/2 ∼ 50 − 200pc, stellar masses of
M⋆ ∼ 107−108M⊙, and star-formation rates of SFR ∼ 0.1−1 M⊙ yr−1
. Our search finds no candidates
at 15 < z < 20, placing upper limits at these redshifts. We develop a forward modeling approach to
infer the properties of the evolving luminosity function without binning in redshift or luminosity that
marginalizes over the photometric redshift uncertainty of our candidate galaxies and incorporates the
impact of non-detections. We find a z = 12 luminosity function in good agreement with prior results,
and that the luminosity function normalization and UV luminosity density decline by a factor of ∼ 2.5
from z = 12 to z = 14. We discuss the possible implications of our results in the context of theoretical
models for evolution of the dark matter halo mass function.
(May 29th, 2024) Advancements in Intravital Microscopy- Insights for Preclini...Scintica Instrumentation
Intravital microscopy (IVM) is a powerful tool utilized to study cellular behavior over time and space in vivo. Much of our understanding of cell biology has been accomplished using various in vitro and ex vivo methods; however, these studies do not necessarily reflect the natural dynamics of biological processes. Unlike traditional cell culture or fixed tissue imaging, IVM allows for the ultra-fast high-resolution imaging of cellular processes over time and space and were studied in its natural environment. Real-time visualization of biological processes in the context of an intact organism helps maintain physiological relevance and provide insights into the progression of disease, response to treatments or developmental processes.
In this webinar we give an overview of advanced applications of the IVM system in preclinical research. IVIM technology is a provider of all-in-one intravital microscopy systems and solutions optimized for in vivo imaging of live animal models at sub-micron resolution. The system’s unique features and user-friendly software enables researchers to probe fast dynamic biological processes such as immune cell tracking, cell-cell interaction as well as vascularization and tumor metastasis with exceptional detail. This webinar will also give an overview of IVM being utilized in drug development, offering a view into the intricate interaction between drugs/nanoparticles and tissues in vivo and allows for the evaluation of therapeutic intervention in a variety of tissues and organs. This interdisciplinary collaboration continues to drive the advancements of novel therapeutic strategies.
(May 29th, 2024) Advancements in Intravital Microscopy- Insights for Preclini...
Relative value of radar and optical data for land cover/use mapping: Peru example
1. Full Terms & Conditions of access and use can be found at
http://www.tandfonline.com/action/journalInformation?journalCode=tidf20
Download by: [100.36.116.186] Date: 16 November 2017, At: 04:46
International Journal of Image and Data Fusion
ISSN: 1947-9832 (Print) 1947-9824 (Online) Journal homepage: http://www.tandfonline.com/loi/tidf20
Relative value of radar and optical data for land
cover/use mapping: Peru example
Barry Haack & Ron Mahabir
To cite this article: Barry Haack & Ron Mahabir (2017): Relative value of radar and optical data
for land cover/use mapping: Peru example, International Journal of Image and Data Fusion, DOI:
10.1080/19479832.2017.1398188
To link to this article: http://dx.doi.org/10.1080/19479832.2017.1398188
Published online: 06 Nov 2017.
Submit your article to this journal
Article views: 7
View related articles
View Crossmark data
3. When it comes to the mapping of features that cover large areas, for example state,
national, regional or even global scales, remote sensing has typically been relied on as a
primary source of data for mapping and validation purposes. One such application is the
mapping of land cover/use (LCLU) features. LCLU plays an important role in informing
policy decisions for a wide range of applications, including, planning infrastructure,
reducing pollution and expanding food production (Idol et al. 2015a). Up-to-date
information on LCLU is also important for achieving goal 15 of the SDG, which is ‘to
protect, restore and promote sustainable use of terrestrial ecosystems, sustainably
manage forests, combat desertification, and halt and reverse land degradation and
halt biodiversity loss’ (United Nations 2017). Yet, for many places around the world,
obtaining up-to-date information on LCLU continues to be a challenge.
Traditionally, LCLU relied upon the use of images captured from multispectral sensors
onboard spaceborne systems such as the Landsat missions. While such information has
been extensively used for mapping LCLU (e.g. Homer et al. 2007, Griffiths et al. 2014), the
wavelengths of these systems are unable to penetrate clouds and haze conditions. This
presents an issue for regions around the world where persistent cloud cover (e.g. tropical
and high latitude areas) and atmospheric disturbances (e.g. pollution) are typical.
Furthermore, optical sensors such as the Landsat-8 Operational Land Imager passively
collect land surface information, which means that they rely on the Sun’s energy.
Most spaceborne radar sensors actively collect land surface information at much
longer wavelengths, which overcome the previous mentioned issues with optical sen-
sors (Idol et al. 2015b). Other radar systems (e.g. Bistatic Synthetic Aperture Radar)
usually dissociate receiver and antennae to two separate spaceborne systems (Tan
et al. 2005). Compared to multispectral imagery, radar data are much more complex
to process and extract information from, along with such imagery being much less
intuitive to interpret (Richards 2013). These factors, in addition to the limited availability
of spaceborne radar data in comparison to multispectral data, have led to the much
lower usage of radar data in LCLU mapping applications.
One consideration when using radar data for LCLU mapping is which polarisation
channel/band to use. Traditionally, only one band was used to collect radar information,
which limited the amount of backscatter being received at the sensor. In this case, a
single polarisation was transmitted and a single polarisation was received, producing an
image that was either horizontal–horizontal (HH), or vertical–vertical (VV) polarisation.
Newer quad-polarisation systems can capture all four polarisations (HH, HV, VH and VV),
permitting more surface scattering to be imaged. This is important since each polarisa-
tion can be used to capture different physical properties of land surface features (Haack
and Mahabir 2017). Such information can work in tandem with optical imagery to
improve the accuracy of LCLU maps. As a result, various studies have explored the
fusion of optical and radar imagery and have shown improved LCLU mapping accuracies
compared to using each type of data on its own (e.g. Amarsaikhan et al. 2012, Pereira
et al. 2013, Idol et al. 2015a, Xiao et al. 2016).
However, as highlighted in a recent review by Joshi et al. (2016), few studies have
explored the fusion of optical and radar data for LCLU mapping (50 studies between
1996 and 2016). That study also showed that the geographical distribution of such
research has been highly skewed. For example, 17 of the 50 studies were in Europe, this
was in comparison to only 6 studies located in South America (5 in Brazil and 1 study in
2 B. HAACK AND R. MAHABIR
Downloadedby[100.36.116.186]at04:4616November2017
4. Ecuador). Evidently, there is a pressing need for the expansion of research examining the
fusion of optical and radar data in other unexplored areas. Such research will not only
assist in better understanding the potential benefits of radar as it applies to LCLU
mapping applications but also serve as a baseline for the design of the next generation
of earth observation systems for LCLU monitoring at regional and global scales.
While the fusion of optical and radar data has certainly led to improvements in LCLU
mapping accuracies, this has also resulted in the use of large multisensor data stacks.
Thus, a new challenge has emerged wherein the determination of what bands should be
used for analysis and mapping has become an issue. Prior to the availability of free
sources of remote sensing data, such as the Landsat missions, the persistence of clouds
making some images unusable and the cost of fine resolution imagery, these factors all
assisted in limiting the amount of image bands used for remote sensing applications.
Some researchers limit the amount of data to two or even three bands from a single
sensor based on familiarity or the availability of data (Frate et al. 2008, Al-Tahir et al.
2009). However, this has resulted in missed opportunities for understanding the bio-
physical properties of different LCLU features as observed from using multiple bands
and from different sensors.
The determination of the most suitable image bands also has importance in the visual
analysis of remote sensing imagery, still one of the most widely used approaches in
digital image analysis. This often requires the reduction in the number of bands to 3 to
be used for creating a red, green, blue (RGB) true or false colour image composite. Such
spectral three band combinations are widely used to highlight various LCLU features
such as soil, agriculture and urban areas (Harris Geospatial 2013). Further, if only three
image bands were to be considered, this would mean that the best RGB image would be
one of six different RGB combinations of these three bands, that is, an image can be
either RGB, RBG, GRB, GBR, BRG or an BGR composite. However, as the number of image
bands increases, the number of RGB combinations increases factorial. In such cases, the
manual determination of the best three band combination for visual analysis becomes
very challenging.
Besides visual analysis, the determination of what image bands to be used in analysis
can be helpful in other ways. One such benefit is the removal of redundant data, which
leads to shortened processing times and improvements in feature detection (Landgrebe
et al. 2001, Richards 2013, Li et al. 2014). Also, as the number of image bands increases,
the number of observations required to train remote sensing classifiers increases expo-
nentially, a paradox better known as the Hughes’ Phenomenon (Hughes 1968). For
features that usually occupy very small areas in relation to the full extent of the study
area being examined, such skewed distributions may have impacts on their classification
and mapping. In fact, recent work by Haack and Mahabir (2017) suggests that some
remote sensing classification algorithms, beyond a certain optimum number of bands,
may lead to degradation in classification accuracy. That study showed that no more than
six bands were needed for a viable classification using a maximum likelihood classifier.
Similarly, Le Bris et al. (2014) showed that only five to six image bands were needed for
LCLU classification when using a support vector machine. The results of these studies
and others are no doubt partly linked to the properties of the LCLU features being
investigated. Such properties include the number of classes to be classified, the spectral
separability within and among classes, the preprocessing steps involved in preparing the
INTERNATIONAL JOURNAL OF IMAGE AND DATA FUSION 3
Downloadedby[100.36.116.186]at04:4616November2017
5. image data prior to analysis and morphological characteristics of features being mapped
in relation to their environment. Moreover, knowledge of what image bands are useful
for various applications plays an important role in the design and deployment of future
spaceborne sensors. In this case, image bands that are less likely to be used may be
discontinued and their resources used to capture other wavelengths in the electromag-
netic spectrum.
The need to determine what image bands to be used prior to image classification has led to
the development of several statistical approaches to be used for this purpose. These
approaches can be divided into two main groups: feature extraction and feature selection.
Feature extraction approaches transform a set of image bands onto a lower dimensional space
producing a smaller number of bands. In this case, a statistical relationship, usually linear,
among images bands (e.g. variance) is used to remove unnecessary or unwanted data.
However, as in the case of principal component analysis (PCA – Pearson 1901), the resulting
image bands are not always intuitive to interpret. Feature selection approaches, on the other
hand, result in the selection of a subset of the original bands (Deliot and Kervella 2010). One
such approach is the use of various spectral separability measures, which include distance
measures such as divergence, transformed divergence, Bhattacharyya distance and Jeffries–
Matusita distance. Excellent reviews of these measures can be found in Swain and Davis (1978),
Latty and Hoffer (1981) and Swain et al. (1981), with studies having significant impact in this
area including work by Swain and King (1973), Goodenough et al. (1978) and Mausel et al.
(1990) just to name a few.
While studies using different methods to reduce the number of image bands for
classifying remote sensing imagery have been ongoing, they have mainly concentrated in
developed countries. At these locations, data are usually much more available and acces-
sible in comparison to developing countries. This is important, since as Mahabir et al. (2016)
suggests, developing countries are experiencing much more rapid changes due to increas-
ing urbanisation, political and civil unrest occurring in many such places. Also, while one
may argue that large-scale mapping initiatives exist that overcome such data poverty issues
in the developing world (e.g. Bontemps et al. 2011, Jun et al. 2014), such studies use
nomenclature that may not always be suitable for some locations due to unique cultural
and socio-economic factors impacting the specific landscapes. Such factors in turn may lead
to some separability measures being more suitable for some areas compared to others. This
is important since the use of one measure that may be unsuitable in other locations may
impair our understanding of the underlying LCLU processes taking place at those locations.
The aim of this study was to assess the suitability of various spectral separability
measures to determine the most suitable image band and band combinations to be
used prior to remote sensing LCLU image classification. The most suitable bands were
further analysed with respect to their spectral and spatial properties and linked to the
underlying characteristics of the LCLU. This is useful since many studies that use
separability measures do so without regard to understanding the underlying character-
istics of those features that make them more or less separable in remote sensing
imagery. Without such knowledge, it is difficult to determine whether separability
measures selected for specific applications are suitable, especially when working with
different types of data, as is the case in this study. Moreover, the application of such
measures in the context of developing countries may provide useful information in
prioritising the collection of data for different application areas. The spectral separability
4 B. HAACK AND R. MAHABIR
Downloadedby[100.36.116.186]at04:4616November2017
6. measures evaluated in this study (discussed further in Section 3) were specifically chosen
because they are available in a wide range of remote sensing software such as Erdas
Imagine (Hexagon Geospatial 2017) and PCI Geomatica (PCI Geomatics 2017), as well as
in several open source packages such as the R suite (R Core Team 2017). As a result, this
study, or parts of this study, can be replicated or modified to meet the needs of local or
national stakeholders in the selected study area, as well as in other countries.
This study also evaluates the impact that feature extraction prior to the application of
spectral separability has on the selection the optimum number of image bands for LCLU
classification. The study area used is a site in Arequipa, Peru, which presented an
interesting landscape as discussed further in Section 2. Following this, the data and
methods are described, and the results and conclusions discussed.
2. Study area and data
The site selected for this analysis was Arequipa, Peru. Figure 1 is a Landsat Thematic
Mapper (TM) image for the Arequipa study area. Arequipa is about 100 km from the
South Pacific Ocean (Google Earth 2017) at an elevation of 2350 m (Holmgren et al.
2001). It is a west coast desert with a very hot and dry climate. The average temperature
Figure 1. Arequipa subscene. Landsat Thematic Mapper 12 October 2008. TM bands 2, 3, 4 in BGR.
Subscene width approximately 6.5 km.
INTERNATIONAL JOURNAL OF IMAGE AND DATA FUSION 5
Downloadedby[100.36.116.186]at04:4616November2017
7. during the daytime is 22°C, which drops to about half this temperature at night. The
average precipitation in Arequipa is 104 mm (Carpio and Fath 2011), with the highest
precipitation of about 40 mm occurring in February (Weather and Climate 2016).
Arequipa is the second largest city in Peru with a population of about 1.3 million people
in 2012 (Knoema 2017). The city is very industrialised with irrigated agriculture on the
periphery, including, corn, potatoes and other vegetables (Carpio and Fath 2011).
As shown in the subscene in Figure 1, the study area is dominated by extensive urban
features, with considerable texture. The airport, centre of Figure 1, is dominated in all
directions by urban areas, which also contains some small parks shown with more pro-
nounced rectangular geometric shape and with much smoother texture compared to urban
areas. These parks typically occur in residential neighbourhoods, which is a common feature
of planned neighbourhoods in this region. Some larger park areas occur aswell. The
commercial and industrial areas have visibly larger buildings and coarser texture, especially
to the southwest of the airport. The dominant landform features in the study area are the
Andes Mountains, an extension of which can be seen to the north of the city. To the north of
the airport is a large area of bare soil with similar tones to urban areas, but with much
smoother texture. There is also a very highly reflective salt flat area in the southernpart of
the image. Also visible in the southern portion of the subscene, there are many agriculture
fields, almost all of which are irrigated and are visible as large rectangular patchworks
composed of different tones in Figure 1.
This study utilised both radar and optical data. PALSAR L-band dual-polarisation radar
imagery were collected on 16 October 2008. These data were used to derive 3 variance
texture measures at window sizes of 5 × 5, 11 × 11 and 17 × 17, and for each polarisation
band. The decision to use variance texture was based upon previous research, which
suggested that this measure produces adequate LCLU mapping accuracies (Idol et al.
2015a). Also, following previous work by Idol et al. (2017), the radar data were not
despeckled prior to the extraction of texture since that study showed that this can lead to
lower classification performance. Optical imagery were acquired from the Landsat 5 TM
sensor on 12 October 2009. The acquisition date of the optical data is 1 year after the radar
data. It is often difficult to acquire imagery from different sensors at the same time. This is
due to several reasons including different satellite orbits and in the case of optical imagery
over the study area, large amounts of cloud cover. However, the same season for both data
sets was used and it is unlikely that most LCLU features would have changed significantly
over the 1 year period with the exception of the agricultural classes. The TM imagery had
seven spectral bands from the visible to the thermal infrared regions of the electromagnetic
spectrum. The TM spatial resolution was 30 m for all bands except the thermal band which
was 120 m. This resulted in a 15 band data stack: 2 bands from the original dual polarised
radar, 6 radar derived variance texture measures and 7 bands from TM.
Both the radar and optical data were co-registered and the optical imagery resampled
to the 12.5 m spatial resolution of the original PALSAR data using the nearest neighbour
algorithm. The decision to resample to the spatial resolution of the finest resolution data
was done in order to preserve, as much as possible, some of the radar texture that
would have been smoothened if the original radar imagery were resampled to the 30-m
resolution of the optical imagery. The original TM data were in 8 bit radiometric
resolution and the PALSAR in 16 bit. The combination of different radiometric resolu-
tions was of concern. The basic question is should all the data be rescaled to the same
6 B. HAACK AND R. MAHABIR
Downloadedby[100.36.116.186]at04:4616November2017
8. radiometric resolution and if so, what impact might this rescaling may have on selecting
the best bands and band combinations. To resolve this issue, areas of interest (AOI)
polygons for the same area were obtained for the combined 8 and 16 bit 15 band data
stack. The suitability of this heterogeneous radiometric scale combination was evaluated
using separability measures, the results of which were compared to a similar 15 band
data stack where all data were rescaled to 8 bit. The results were identical in separability
values in terms of ranking by band. Therefore, the radiometric resolution of all data was
consistently set at 8 bit for analysis.
The 15 bands for this study are listed in Table 1 while Table 2 contains various first- and
second-order statistics for each individual band. There are some interesting and, at the same
time, some uncertain components of the subscene statistics in Table 2. Band 1, the TM visible
blue has a higher minimum value, 58, than most other bands. This is most likely because the
data have not been compensated for atmospheric issues, so this band includes additive values
from scattering within the atmosphere. The thermal band 6 has a very high mean value and
low standard deviation, which is typical of thermal data. Band 5, the first mid infrared band,
also has a high mean as a result of a surface area with considerable dry bare soil and urban
features such as rooftops and roads, which reflect highly in these wavelengths. Most of the TM
bands have similar standard deviations. Bands 8–15, which are the original radar and derived
texture values, are stretched across the full8 bit range,0to255,from their rescaling from 16bit.
The means and standard deviations for the two original PALSAR bands, 8 and 9, are
very similar. The texture bands, 10–15, have relatively high means and standard deviations
indicating that there is a considerable amount of texture as would be expected from
urban landscapes. There are also areas of low texture, which would increase the standard
deviation, which is understandable as the subscene includes bare soil and agricultural
areas. The texture means and standard deviations also increase with window sizes.
3. Methodology
This study consists of two components. First, spectral signatures were extracted for
various LCLU features using AOI polygons. The LCLU features examined were bare soil,
residential, salt flat, industrial and two locations for agriculture. These LCLU classes are
Table 1. Arequipa, Peru image bands.
Band Sensor Band Date Description
1 Landsat TM 1 12 October 2009 Visible blue
2 Landsat TM 2 12 October 2009 Visible green
3 Landsat TM 3 12 October 2009 Visible red
4 Landsat TM 4 12 October 2009 Near infrared
5 Landsat TM 5 12 October 2009 MIR-1
6 Landsat TM 6 12 October 2009 Thermal IR
7 Landsat TM 7 12 October 2009 MIR-2
8 PALSAR HH 16 October 2008 Horizontal–horizontal
9 PALSAR HV 16 October 2008 Horizontal–vertical
10 PALSAR Texture HH 16 October 2008 Variance 5 × 5
11 PALSAR Texture HV 16 October 2008 Variance 5 × 5
12 PALSAR Texture HH 16 October 2008 Variance 11 × 11
13 PALSAR Texture HV 16 October 2008 Variance 11 × 11
14 PALSAR Texture HH 16 October 2008 Variance 17 × 17
15 PALSAR Texture HV 16 October 2008 Variance 17 × 17
INTERNATIONAL JOURNAL OF IMAGE AND DATA FUSION 7
Downloadedby[100.36.116.186]at04:4616November2017
9. generalised and limited in number, and as shown in Joshi et al. (2016); such broad
categories are not unusual in LCLU mapping studies that integrate both radar and
optical data. In the case of this research, the use of these broad LCLU classes was
used to first obtain a generalised understanding of LCLU distribution in the study
area. Based upon the results of this study, a more detailed classification using more
LCLU classes, for example different crop types, may be incorporated. Only one signature
was extracted for each LCLU to eliminate the confusion of low spectral separability
between the same cover types to permit interclass comparisons. As large an AOI as
possible was created for each LCLU feature. However, for several classes, this was not
possible due to the distribution of these classes within the study area. The AOI pixel
counts were bare soil (8971), residential (12,287), salt flat (780), industrial (4020), agri-
culture-1 (406) and agriculture-2 (193).
Table 3 contains the spectral signatures for the various LCLU classes. The values for the
TM bands are quite reasonable. There are also significant differences in mean values
between the classes in all TM bands. The salt flat has the highest mean values in all bands.
The two agricultural classes have very similar patterns in mean values across all TM bands
but the second signature has consistently higher values. The visible blue band has
Table 2. Band mean and standard deviations for Arequipa data stack.
Band Minimum Maximum Mean Standard deviation
1 58 255 114 20.4
2 25 162 63 12.8
3 26 198 80 20.0
4 30 186 89 17.9
5 30 255 125 29.0
6 137 197 166 9.7
7 16 245 80 21.8
8 1 255 17 17.1
9 1 255 17 12.4
10 1 255 47 67.3
11 1 255 49 57.5
12 1 255 67 75.8
13 1 255 70 63.9
14 1 255 79 79.5
15 1 255 82 66.1
Table 3. Arequipa Peru class signatures (mean/standard deviation).
Band Bare soil Residential Salt flat Industrial Agriculture-1 Agriculture-2
1 TM blue 118/4.4 121/7.4 159/7.4 143/13.0 73/5.7 89/3.9
2 TM green 67/2.8 66/4.8 101/5.5 84/8.9 38/3.4 52/2.7
3 TM red 88/3.5 84/6.8 145/8.7 115/14.2 37/6.0 53/4.3
4 TM NIR 82/2.9 77/6.4 146/8.4 110/15.1 141/14.1 154/12.3
5 TM MIR 1 130/6.2 114/9.5 251/8.0 181/28.3 84/11.0 125/7.7
6 TM Thermal 185/4.5 166/3.9 170/3.3 168/3.1 146/4.5 151/1.6
7 TM MIR 2 85/3.8 79/6.6 168/11.7 121/17.9 34/6.9 51/4.3
8 PALSAR HH 6/2.5 18/9.0 7/4.6 13/10.5 11/3.9 17/7.7
9 PALSAR HV 6/3.2 27/12.6 6/3.2 16/12.4 10/5.7 20/12.9
10 HH texture 5 × 5 5/4.1 43/43.1 12/11.6 38/50.4 14/19.4 59/58.7
11 HV texture 5 × 5 7/12.2 86/57.3 6/6.9 68/73.1 18/23.8 96/82.1
12 HH texture 11 × 11 5/3.6 59/46.5 14/6.5 57/55.3 21/16.2 145/81.4
13 HV texture 11 × 11 8/10.1 117/47.2 8/4.6 106/74.0 31/21.0 149/68.7
14 HH texture 17 × 17 6/3.2 66/46.0 15/4.7 72/59.4 37/45.9 214/50.7
15 HV texture 17 × 17 8/8.0 132/39.1 8/3.0 131/69.0 37/14.1 188/59.3
8 B. HAACK AND R. MAHABIR
Downloadedby[100.36.116.186]at04:4616November2017
10. relatively high average values in all classes. This is primarily because of the additive effect
of the atmosphere. The first mid-infrared band, band 5, has the largest variation in mean
values from 84 for the agricultural-1 class to 251 for the salt flat. Not surprisingly, the
industrial class has the largest standard deviations because of the variation in features
including different roofing materials, as well as roads and open areas. As would be
expected there is little variation of the mean thermal band values, band 6, which is also
supported by the low standard deviations for this band. The slightly lower band 6 values
for the agricultural classes are likely due to the agricultural land being irrigated.
The radar and radar texture responses are more complicated. The backscatter values
for the original PALSAR, bands 8 and 9, for most classes are quite low. The mean values
for the HV band are slightly higher than the values for the HH band. As expected, the
residential and industrial classes have much larger standard deviations. The second
agricultural class also has higher standard deviations in the original PALSAR data
especially for the HV band, which may be due to direct scattering on recently irrigated
fields. For some classes, their low mean and standard deviation values may make them
more separable amongst the other classes. For example, the bare soil and salt flat LCLU
classes have much lower mean and standard deviation values than the other classes. It is
somewhat surprising that the residential LCLU class has higher mean backscatter than
the industrial. This may be due to features in the study area such as parking lots
between the buildings in the industrial areas, which would lead to reduced mean
backscatter.
The variance texture means vary much more than the original PALSAR backscatter
values. In most cases, the larger window sizes have higher mean texture values and the
HV values are higher than those of the HH band. As expected, the mean texture values
for bare soil and salt flat are very low and those for residential and industrial very high.
The texture values for the second agricultural class are also very high. One concern for
the physically smaller classes is that the larger texture windows may have been influ-
enced by surrounding edge features. Based simply upon the means and standard
deviations, it is apparent that the texture values will provide considerable separability
for some classes.
The second component of this study was to use spectral separability measures to
determine the best single band and band combinations for different numbers of bands.
Four measures, divergence, transformed divergence, Euclidian and Jeffries–Matusita
distance, were applied to the 15 band data stack. Besides divergence, all other measures
became saturated at maximum values for multiple combinations of the same number of
bands, thus providing little effective information. Singh et al. (1999) reported a similar
pattern of saturation with transformed divergence for broad LCLU classes in Northern
India as the number of image bands increased. However, this result was not tested in the
present study and only the divergence measure was used. An additional study might
compare these separability measures in greater depth to better understand why they
became saturated.
Divergence is calculated from the means and covariance matrices of each spectral
class. It is a measure of statistical distance between class or site pairs of interest and
provides information on their spectral separability. This separability is an indirect esti-
mate of the likelihood of correct classifications between groups of different band
combinations (Swain et al. 1981). Divergence is an estimate of information usually
INTERNATIONAL JOURNAL OF IMAGE AND DATA FUSION 9
Downloadedby[100.36.116.186]at04:4616November2017
11. obtained by the time-consuming and expensive process of actual classification and
accuracy evaluations. The formula for divergence is (Swain and Davis 1978):
Dij ¼
1
2
tr½ Covi À Covj
À Á
CovÀ1
i À CovÀ1
j
þ
1
2
tr
!
CovÀ1
i À CovÀ1
j
μi À μj
À Á
μi À μjÞT
i
(1)
where i and j are the spectral signatures of the two classes to be being compared, Cov
and μ are the covariance matrix and mean vectors for classes i and j. Finally, tr and T are
the trace and transposition functions. To assess the divergence separability for more
than 2 classes, 6 in this study, the average divergence between class pairs was used. The
formula for deriving the average divergence between class pairs follows (Richards 2013):
divavg ¼
Xm
i¼1
Xm
j¼1
p wið Þ p wj
À Á
Divi;j (2)
where p wið Þ and p wj
À Á
are the prior class probabilities for class i and class j, m is the
number of classes and Divi; j the values between those classes. The average divergence
values between class pairs were studied and related to the properties of surface features
and their spectral signatures in order to gain a better understanding as to why some
classes are more or less separable in remote sensing imagery.
Average divergence was also used to determine the best bands for LCLU classifica-
tion. This was done for the best single band, then the best two bands, and progressing
for an increasing number of bands, best three, best four etc. In this case, the best N
bands were selected by applying Equation 2 to all combinations of N bands. For
example, if four bands were used, the best three bands would be one of four band
combinations: bands 1, 2 and 3, bands 1, 2 and 4, bands 1, 3 and 4 and band 2, 3 and 4,
with the best three band combinations having the highest divergence value. The best
band and band combinations were determined based on the average divergence value
for all 15 class pairs of spectral signatures. It should be noted that the order in which
image bands were evaluated has no impact on the overall divergence value based on
Equations 1 and 2. In addition to creating a data stack of Landsat and PALSAR data for
this study, an additional examination was carried out to determine the relative value of
PCA. PCA is one of the most widely employed data reduction or transformation methods
in remote sensing as well as in many other disciplines. PCA transforms the original
image to new axes composed of linear combinations of existing bands. This transforma-
tion method is useful in that it reduces data redundancy between bands as well as
accentuates the most important data in the derived components (Balaji and Sumathi
2014). The unique spectral content within the first two derived PCA bands can often
account for as much as 93% of the variability contained within the original bands
(Muchoney and Haack 1994, Campbell and Wynne 2011). However, these results can
vary from one application to the next. PCA was run on the 15 band data stack to create
six band components. These components contained almost 95% of the variance con-
tained within the original data, with only very small increments in variance with the
inclusion of the remaining components.
An initial effort made to use the original 8-bit PCA bands without stretching failed as
there were several spectral signature bands with mean values of 0, which the divergence
10 B. HAACK AND R. MAHABIR
Downloadedby[100.36.116.186]at04:4616November2017
12. method could not process and provided error messages. The Erdas software uses a
mean of 0 and unit value of 1 to standardise each PCA component. This may have
reduced the spectral dynamic range between some classes (Balaji and Sumathi 2014),
while compressing others. As a result, some class means may have tended towards 0,
leading to issues with the divergence function. One possible solution would be to derive
unstandardised PCA components and use these in divergence analysis, a topic that will
be investigated in a follow-up study. Subsequently, the 6 PCA component bands were
systematically stretched to their full 8-bit range, following which divergence analysis was
applied.
4. Results
4.1. Best single band
The best individual band based upon divergence analysis, providing the most separ-
ability between LCLU classes in the study area, was the TM visible red band 2 with an
average divergence value of 1962. Initially, this seems surprising; however, considering
the reflectance statistics for the various LCLU classes in this band as shown in Table 3,
the selection of this band is understandable. The two agricultural classes have low
means, the bare soil and residential moderate values and the salt flat and industrial
classes have very high means in this band. In addition, all class means have low standard
deviations making them much easier to separate in the TM red band compared to the
other image bands.
There is a range of divergence values between the 15 class pairs in the TM visible red
band, with values from 24 to 7262. The lowest divergence value of 24 is between the
bare soil and residential with average reflectance values from Table 2 of 88 and 84.
Other low separability classes are the two agricultural classes (237), and residential and
industrial (358), both of which are logical. The highest divergence of 7262 is between the
salt flat and first agricultural class with mean reflectance values of 145 and 37. Among
the other class pairs of high separability are salt flat and the agriculture-2 (4735), and
industrial and agricultural-1 (3806) LCLU classes. As expected, the high and low separ-
ability values are often intuitive based upon knowledge of the feature characteristics,
their appearance in Figure 1 and the LCLU class statistics in Table 3.
Table 4 contains all bands ranked by divergence values. The second and third most
useful bands are the PALSAR variance textures at the largest window of 17 × 17. There is
a considerable range of divergence values by band from a high of 1962 to a low of 7.
The two lowest bands are the two original PALSAR polarisations. Among the TM bands,
based upon subscene statistics in Table 3, it is understandable why the thermal band 6
has the lowest divergence value. The second most useful TM band is the second mid-
infrared band, band 7, followed closely by band 4, the near-infrared band. The least
useful TM bands are the mid-infrared-1 and visible blue bands.
Based upon the information provided in Table 4, it is clear that the usefulness of
texture increases with larger window sizes. This may be in part due to the broad
categories of LCLU coupled with the moderate spatial resolution of the imagery used
in this research. At fine spatial resolutions, and possibly for a more detailed LCLU
classification scheme, the increased variations between pixels tones may lead to
INTERNATIONAL JOURNAL OF IMAGE AND DATA FUSION 11
Downloadedby[100.36.116.186]at04:4616November2017
13. increased ambiguity. However, further testing would need to be done to prove or
disprove this hypothesis. Notwithstanding, the statistics in Table 3 generally assist in
understanding the observed pattern for texture bands. For those classes with
expected high texture, residential and industrial, larger texture window sizes have
higher means and little change in standard deviations, thus increasing separability.
Typically, this increase in divergence with larger window sizes would be expected to
be reversed at some point where continually increasing window size begins to be less
useful, this being a function of pixel resolution and the relative size of landscape
features being examined.
4.2. Best two bands
The best two bands were the TM visible red and the RADARSAT HH variance texture at
17 × 17 window size (3832), which were the two best single bands. Intuitively, this seems
reasonable as these two bands represent very different types of remote sensing data by
wavelengths. Also, whereas the TM data are providing information on the spectral
properties of LCLU features, the derived texture measure is providing contextual infor-
mation on the spatial relationship between image pixels. The highest class pair separ-
ability for these two bands was between bare soil and agriculture-2 classes (17,266). The
lowest class pair separability was between bare soil and residential, as well as between
agriculture-1 and 2, both having a divergence value of 242.
4.3. Best three bands
The best three bands were the TM visible red and near-infrared bands with the PALSAR
HH texture window of 17 × 17 (4652). This combination of bands also generally follows
the pattern of very different types of data being most useful. The best class pair
separability for these three bands was between bare soil and agriculture-2 (9313) and
the least separable were bare soil and residential (289). The best class separability
between bare soil and agriculture-2 LCLU classes is understandable, since as shown
Table 4. Arequipa divergence rank by single band.
Rank Band Divergence value
1 TM red 1962
2 HH texture 17 × 17 1829
3 HV texture 17 × 17 1255
4 TM MIR 2 963
5 HV texture 11 × 11 961
6 TM NIR 931
7 TM green 832
8 TM MIR 1 770
9 TM blue 625
10 HV texture 11 × 11 456
11 TM Thermal 106
12 HH texture 5 × 5 95
13 HV texture 5 × 5 86
14 HV 18
15 HH 7
12 B. HAACK AND R. MAHABIR
Downloadedby[100.36.116.186]at04:4616November2017
14. Table 3, the mean values for these classes for the two TM bands had very different
values. A similar pattern was also observed for the bare soil and agriculture-2 LCLU
classes in the HH texture at 17 × 17 window size. However, it was unclear as to why the
agriculture-2 class had such a high mean value in this texture band compared to the
other texture bands.
There was low separability between bare soil and residential. This was somewhat
surprising since intuitively, they would be expected to be similar in the TM data. In this
case, residential areas would typically be expected to have higher radar backscatter. The
original PALSAR bands in Table 3 indicate higher backscatter for residential; however,
their standard deviation values are also high, which would suggest low class separability.
The second best three band combination was the TM visible red and second mid-
infrared bands, together with the same PALSAR HH variance at 17 × 17 window
(4302). The third best three band combination was TM visible red and near-infrared
with the PALSAR HV variance texture at 17 × 17 window (3967). These best band
combinations are quite similar in the selected bands.
As previously mentioned in Section 1, the selection of the best three bands is very
important in remote sensing for creating colour composites for viewing any imagery and
also for manual thematic information extraction. However, the best three band combi-
nation for Arequipa was examined visually but the large texture window created a very
blocky image, which was not very useful as shown in Figure 2.
4.4. Best four, five and six bands
The best four bands from 1365 possible combinations were the TM visible red and near-
infrared bands together with two texture bands, HV at 11 × 11 window and HH at
17 × 17. The lack of utility of the original PALSAR bands is initially surprising. However,
from Table 3 for all LCLU classes, their means for bands 8 and 9, the original PALSAR, are
quite similar and have relatively high standard deviations for several classes reducing
class separability. The best five bands added the second TM mid-infrared band to the
best four bands. The best six bands added a second texture band, HH at 5 × 5 window,
to the best five bands.
4.5. All band combinations
The divergence values by number of bands follow an expected pattern of initially
increasing with the number of bands. The progression begins with the best individual
band at 1962 and increases to a peak at 6129 with seven bands. The pattern then
decreases to a low of 2655 with all 15 bands as presented in Figure 3. This Figure shows
that there is a negative effect with respect to the separation of LCLU classes with the
addition of too many bands, and for this data set, results suggest that there is no reason
to include more than five or six bands. The divergence value with the best five bands
was 5921, only marginally lower than the highest value at seven bands. This information
is an additional argument for the use of separability analysis. It not only indicates the
best bands but also the number of necessary bands for a viable classification.
INTERNATIONAL JOURNAL OF IMAGE AND DATA FUSION 13
Downloadedby[100.36.116.186]at04:4616November2017
15. Figure 2. Arequipa best three bands. Palsar HH variance from 17 × 17 window, TM visible red and
TM near infrared in RGB. Scene width approximately 6.5 km.
0
1000
2000
3000
4000
5000
6000
7000
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Divergence
Bands
Figure 3. Arequipa divergence values by best combination for different number of bands, horizontal
axis.
14 B. HAACK AND R. MAHABIR
Downloadedby[100.36.116.186]at04:4616November2017
16. 4.6. Principal components analysis (PCA)
Divergence analysis was also used to study the LCLU class separability between the six
derived PCA component bands, and using the same AOIs for LCLU classes that were
used with the 15 band TM, radar and radar-derived texture data stack. As would be
expected from PCA, the divergence values decreased by band from PCA band 1 to PCA
band 6 (425–51). Interestingly, when compared to the single band divergence values for
the original 15 bands in Table 4, these values are very low. The best PCA divergence is
less than the top 10 single band values. For the best PCA 1 divergence, the class pair
values are very understandable. The best divergence is between bare soil and the
second agriculture LCLU class, which are very different features (divergence of 3034).
The second best divergence, but at a much lower value of 935, is between bare soil and
residential. There are two class pairs with a divergence value of 0, which are bare soil
and salt flat, and residential and industrial, both of which would be expected based
upon their appearance and class signatures.
The best three PCA bands by divergence are 1, 3 and 6 with a value of 759. This is
somewhat surprising as initially one might expect the first three bands. However, the
different bands are related to varied surface features. This divergence value for three
bands is well below the best three from the non-PCA stacked approach, which was 4652
for the TM visible red and near-infrared bands with the PALSAR HH texture window of
17 × 17. Even if all six PCA bands were to be used, the average divergence was only 854.
There was no clear reason for the low divergence values derived from the PCA analysis.
Perhaps these values occurred as a result of the rescaling of the PCA components.
However, as stated before, without rescaling, the divergence algorithm would not work.
An extension of this study might be to do classifications and accuracy assessments with
the two sets of data, the 15-layer data stack and the unstretched PCA components and
to compare results.
5. Discussion and conclusions
The increasing availability of spaceborne remote sensing data over the last several
decades has led to a substantial increase in the number applications and users of
these data. One such application, LCLU mapping, has consistently relied on remote
sensing as a main source of mapping and validation data. Traditionally, LCLU maps
depended on information extracted from optical sensors; however, newer approaches to
extracting information now combine information retrieved from different parts of the
electromagnetic spectrum such as the microwave region. This has led to use of large
multisensor data stacks in the mapping of LCLU. While such multisensor integration has
led to improved LCLU mapping accuracies, new issues have emerged such as the need
to determine what image bands should be used for achieving maximum or even optimal
mapping accuracies. With few bands, the problem of what image bands to be used for
analysis may not be as challenging. However, as the number of bands increases, the
decision of what combination of bands to be used quickly becomes a factorial problem.
Such issues are only expected to be exacerbated with the continued growth, advance-
ment and the deployment of spaceborne sensors seeking to collect information at
increasingly finer spatial, temporal, spectral and radiometric resolutions. Moreover,
INTERNATIONAL JOURNAL OF IMAGE AND DATA FUSION 15
Downloadedby[100.36.116.186]at04:4616November2017
17. while traditionally spaceborne sensors collected snap shots of the earth’s surface, more
recent technologies such as CubeSats are being manufactured at a fraction of the cost of
traditional satellites with the ability to do video imaging. This greatly expands the
amount of remote sensing data available to users.
This study examined the use of spectral separability measures, in particular, the
divergence measure, as one approach towards searching through large stacks of data
to determine what bands should be used for LCLU mapping. In addition, an effort was
made to link the results of divergence analysis to the spectral and spatial properties of
the LCLU. This was important to better understand the underlying characteristics of
LCLU that make some features more or less easy to separate in remote sensing imagery
compared to others. Further, the study area, Arequipa, Peru, presented an interesting
case study of a developing country where topography, such as mountainous terrain,
makes the use of remote sensing a valuable tool in capturing up-to-date information on
LCLU changes.
The results of the divergence analysis determined that the best single band,
based on a 15 band data stack composed of TM imagery, radar and derived radar
textures at different window sizes, was the TM visible red. This was followed by the
HH and HV texture bands extracted at the largest window size of 17 × 17. These
results corroborated with the class spectral signatures for the various LCLU classes
in Table 3, highlighting the fundamental role that basic statistics extracted from
remote sensing imagery continue to play in the selection on image bands for LCLU
mapping. Additional observations from this study include the limited value of the
two original PALSAR HH and HV polarisation bands. It was also observed that as
the window size used to extract texture increased from 5 × 5 to 17 × 17, the
divergence value also increased suggesting increased LCLU mapping accuracies.
An examination of the best combination of image bands to achieve maximum
mapping accuracies showed that bands composing of different data from different
sensors produced the best divergence values. This finding highlights the importance
for the continual experimentation of different types of data when trying to both
map and understand features in remote sensing imagery. Moreover, additional
analysis assessing the relative value of PCA determined that this approach per-
formed poorly when trying to separate the various LCLU classes. Of course, this
could be due to limitations with the data stack used or may be the way the PCA
combined the data prior to divergence analysis. Other factors, such as the inap-
propriate selection of components, may have also contributed to the poor perfor-
mance of PCA. Cheriyadat and Bruce (2003), for example, showed that the
components explaining the highest variance in the data, as use in this study, and
used for classification may not always yield the best classification results. Therefore,
further experimentation with the full complement and combinations of individual
principal components is needed to determine if such measures will lead to improved
LCLU class separability.
The results of this study also showed that divergence values as expected initially
increased as the number of bands increased. This indicates better separability and poten-
tially increased LCLU mapping accuracies. However, a maximum divergence value was
achieved at seven bands. This was only slightly higher than divergence values achieved
when using five or six bands and would suggest that no more than five or six bands are
16 B. HAACK AND R. MAHABIR
Downloadedby[100.36.116.186]at04:4616November2017
18. needed for a viable classification. The six bands needed for a viable classification were the
TM visible red, near-infrared band, the second TM mid-infrared band, the radar texture
bands 11 × 11 HV, 5 × 5 HH and 17 × 17 HH. After peaking at seven bands, the divergence
values decreased with the successive introduction of more image bands. These results
provide a compelling argument for the use of separability measures such as divergence for
identification of the best bands for the mapping of features in large image data stacks.
Besides improvements in LCLU classification accuracy, greater selectivity and reduc-
tion of image bands are also expected to reduce processing time during analysis. This is
especially important when applying machine-learning algorithms such as a support
vector machine to classify imagery (Catak and Balaban 2013). Also, bands that are not
found to be of limited use can be substituted or removed from future similar analysis.
For example, in this study, the PALSAR HH and HV polarisation bands were found to
have limited use amongst the other data used. Such approaches can greatly benefit
remote sensing scientists and practitioners that may be overwhelmed with the increas-
ing amount of remote sensing data available to them. Knowing which sensors or derived
values are also likely to provide the best classification results may also reduce the cost
and effort of data acquisition. This could be as trivial as identifying specific image bands
or as part as larger multilevel framework. With respect to the latter, free and coarser
resolution imagery can be used to identify hotspots such as degrading forest areas,
followed by the purchase of finer resolution imagery over these specific areas to better
understand causative factors.
Along with reduced processing times and costs in acquiring data, the methodology
used to determine the optimal bands for classification in this study offers a simple
method that can be used to experiment with different types of data, and for different
applications. This is especially important for developing countries where issues such as
persistent cloud cover are a typical occurrence, and where the availability of up-to-date
information on LCLU and other spatial phenomena continues to be an ongoing chal-
lenge. Finally, the methodology and results of this study can be used to better under-
stand the underlying characteristics of the LULC in other areas. This provides an
important first step towards creating a comprehensive LCLU monitoring programme.
For example, knowledge of the spectral characteristics of agricultural fields in remote
sensing data can be used to monitor agricultural productivity (e.g. Chandna et al. 2012).
This information, combined with other information such as population expansion and
rates of forest decline, can be a powerful driver of sustainable growth in large cities such
as Arequipa. Future research will further investigate different data stacks and study
areas, along with comparing other separability measures and data compression techni-
ques. This also includes the use of fully polarimetric radar systems such as RADARSAT-2.
Moreover, these could be investigated with respect to the LCLU information captured at
different spatial scales and at different dates to determine the rates at which different
LCLU classes may be changing. Such efforts are expected to provide important quanti-
tative information that can be used for informing policy changes.
Acknowledgement
The Alaska Space Facility, under sponsorship from NASA, provided the PALSAR imagery for this
study.
INTERNATIONAL JOURNAL OF IMAGE AND DATA FUSION 17
Downloadedby[100.36.116.186]at04:4616November2017
19. Funding
The Alaska Space Facility, under sponsorship from NASA, provided the PALSAR imagery for this
study.
References
Al-Tahir, R., Richardson, T., and Mahabir, R., 2009. Advancing the use of Earth observation systems
for the assessment of sustainable development. The Journal of the Association of Professional
Engineers of Trinidad and Tobago, 38, 6–15.
Amarsaikhan, D., et al., 2012. Comparison of multisource image fusion methods and land cover
classification. International Journal of Remote Sensing, 33, 2532–2550. doi:10.1080/
01431161.2011.616552
Balaji, T. and Sumathi, M., 2014. PCA based classification of regional and identical features of remote
sensing images. International Journal of Engineering and Computer Science, 3, 7221–7228.
Bontemps, S., et al., 2011. Globcover 2009 - Products description and validation report. Louvain-la-
Neuve, Belgium: UniversiteCatholique de Louvain and European Space Agency.
Campbell, J. and Wynne, R., 2011. Introduction to remote sensing. 5th ed. New York: Guilford Press, 626.
Carpio, O.V. and Fath, B.D., 2011. Assessing the environmental impacts of urban growth using land
use/land cover, water quality and health indicators: a case study of Arequipa, Peru. American
Journal of Environmental Sciences, 7, 90–101. doi:10.3844/ajessp.2011.90.101
Catak, F.O. and Balaban, M.E., 2013. CloudSVM: training an SVM classifier in cloud computing
systems. In: Q. Zu, B. Hu, and A. Elci, eds. Pervasive computing and the networked world. New
York, NY: Springer, 57–69.
Chandna, P., et al., 2012. Using remote sensing technologies to enhance resource conservation
and agricultural productivity in underutilized lands of South Asia. Applied Geography, 32, 757–
765. doi:10.1016/j.apgeog.2011.08.006
Cheriyadat, A. and Bruce, L.M., 2003. Why principal component analysis is not an appropriate
feature extraction method for hyperspectral data. In: IEEE geoscience and remote sensing
symposium, 21-25 July, Toulouse, France, 3420–3422.
Deliot, P. and Kervella, M., 2010. Stochastic band selection method based on a spectral angle class
separability criterion. SPIE Proceedings on Image and Signal Processing for Remote Sensing, 7830, 6.
Frate, F.D., Pacifici, F., and Solimini, D., 2008. Monitoring urban land cover in Rome, Italy, and its
changes by single-polarization multitemporal SAR images. IEEE Journal of Selected Topics in
Applied Earth Observation and Remote Sensing, 1, 87–97. doi:10.1109/JSTARS.2008.2002221
Goodenough, D.G., Narenda, P.M., and O’Neill, K., 1978. Feature subset selection in remote sensing.
Canadian Journal of Remote Sensing, 4, 143–148. doi:10.1080/07038992.1978.10854976
Google Earth, 2017. Available from: https://www.google.com/earth/.
Griffiths, P., et al., 2014. Forest disturbances, forest recovery, and changes in forest types across the
Carpathian ecoregion from 1985 to 2010 based on Landsat image composites. Remote Sensing
of Environment, 151, 72–88. doi:10.1016/j.rse.2013.04.022
Haack, B., and Mahabir, R., 2017. Separability analysis of integrated spaceborne radar and optical
data: sudan case study. Journal of Remote Sensing Technology, 5, 10-21. doi: 10.18005/
JRST0501002
Harris Geospatial, 2013. The many band combinations of Landsat 8. Available from: http://www.
harrisgeospatial.com/Home/NewsUpdates/TabId/170/ArtMID/735/ArticleID/14305/The-Many-
Band-Combinations-of-Landsat-8.aspx [Accessed 23 January 2017].
Hexagon Geospatial, 2017. Available from: http://www.hexagongeospatial.com.
Holmgren, C.A., et al., 2001. Holocene vegetation history from fossil rodent middens near
Arequipa, Peru. Quaternary Research, 56, 242–251. doi:10.1006/qres.2001.2262
Homer, C., et al., 2007. Completion of the 2001 national land cover database for the conterminous
United States. Photogrammetric. Engineering Remote Sensing., 73, 337–341.
18 B. HAACK AND R. MAHABIR
Downloadedby[100.36.116.186]at04:4616November2017
20. Hughes, G., 1968. On the mean accuracy of statistical pattern recognizers. IEEE Transactions on
Information Theory, 14, 55–63. doi:10.1109/TIT.1968.1054102
Idol, T., Haack, B., and Mahabir, R., 2015a. Radar and optical remote sensing data evaluation and
fusion; a case study for Washington, DC, USA. International Journal of Image and Data Fusion, 6,
138–154. doi:10.1080/19479832.2015.1017541
Idol, T., Haack, B., and Mahabir, R., 2015b. Comparison and integration of spaceborne optical and
radardata for mapping in Sudan. International Journal of Remote Sensing, 36, 1551–1569.
doi:10.1080/01431161.2015.1015659
Idol, T., Haack, B., and Mahabir, R., 2017. Radar speckle reduction and derived texture mesures for
land cover/use classification: a case study. Geocarto, 32, 18–29. doi:10.1080/
10106049.2015.1120356
Joshi, N., et al., 2016. A review of the application of optical and radar remote sensing data fusion to
land use mapping and monitoring. Remote Sensing, 8, 70. doi:10.3390/rs8010070
Jun, C., Ban, Y., and Li, S., 2014. China: open access to Earth land-cover map. Nature, 51, 434–434.
doi:10.1038/514434c
Knoema, 2017. World Data Atlas. Available from: https://knoema.com/atlas/Peru/Arequipa
Landgrebe, D.A., et al., 2001. Introduction to the special issue on analysis of hyperspectral image
data. IEEE Transactions on Geoscience and Remote Sensing, 39, 1343–1345. doi:10.1109/
TGRS.2001.934066
Latty, R.S. and Hoffer, R.M., 1981. Waveband evaluation of proposed Thematic Mapper in forest
cover classification. Laboratory for Applications of Remote Sensing Technical Reports. Paper 34.
Purdue University.
Le Bris, A., et al., 2014. Use intermediate results of wrapper band selection methods: A first step
toward the optimization of spectral configuration for land cover classifications. In: Proceeding
of 680 Workshop on hyperspectral image and signal processing: evolution in remote sensing.
25-27 June, Lausanne, Switzerland.
Li, S., et al., 2014. A novel approach to hyperspectral band selection based on spectral shape
similarity analysis and fast branch and bound search. Engineering Applications of Artificial
Intelligence, 27, 241–250. doi:10.1016/j.engappai.2013.07.010
Mahabir, R., et al., 2016. The study of slums as social and physical constructs: challenges and
emerging research opportunities. Regional Studies, Regional Science, 3, 399–419. doi:10.1080/
21681376.2016.1229130
Mausel, P.W., Kramber, W.J., and Lee, J.K., 1990. Optimum band selection for supervised classifica-
tion of multispectral data. Photogrammetric Engineering and Remote Sensing, 56, 55–60.
Muchoney, D. and Haack, B., 1994. Change detection for monitoring forest defoliation.
Photogrammetric Engineering and Remote Sensing, 60, 1243–1251.
PCI Geomatics, 2017. Available from: http://www.pcigeomatics.com.
Pearson, K., 1901. On the lines and planes of closest fit to systems of points in space. Philosophical
Magazine, 6, 559–572.
Pereira, L.O., et al., 2013. Optical and radar data integration for land use and land cover mapping in
the Brazilian Amazon. GIScience Remote Sensing, 50, 301–321.
R Core Team. 2017. R: a language and environment for statistical computing. R Foundation for
Statistical Computing. Available from: https://www.R-project.org.
Richards, J.A., 2013. Remote sensing digital image analysis: an introduction. 5th ed. NY: Springer,
494.
Singh, R.P., Dadhwal, V.K., and Navalgund, R.R., 1999. Wheat crop inventory using high spectral
resolution IRS-P3 MOS-B spectrometer data. Journal of the Indian Society of Remote Sensing, 27,
167–173. doi:10.1007/BF02991570
Space Industry Association, 2016. State of the satellite industry report. Available from: http://www.
sia.org/wp-content/uploads/2017/03/SSIR-2016-update.pdf [Accessed 27 March 2017].
Swain, P.H. and Davis, S.M., eds., 1978. Remote sensing: the quantitative approach. NY: McGraw Hill,
396.
INTERNATIONAL JOURNAL OF IMAGE AND DATA FUSION 19
Downloadedby[100.36.116.186]at04:4616November2017
21. Swain, P.H. and King, R.C., 1973. Two effective feature selection criteria for multispectral remote
sensing. LARS Technical Reports. Paper 39. Available from: http://docs.lib.purdue.edu/larstech/
39/ [Accessed 31 March 2017]
Swain, P.H., Robertson, T., and Wacker, A.G., 1981. Comparison of the divergence and B-distance in
feature selection. West Lafayette, IN, Laboratory for the Application of Remote Sensing Note
027801. Perdue University.
Tan, D.K.P., et al., 2005. Passive radar using global system for mobile communication signal: theory,
implementation and measurements. IEEE Proceeding of Radar, Sonar and Navigation, 152, 116–
123. doi:10.1049/ip-rsn:20055038
United Nations, 2017. Sustainable development goals. Available from: https://sustainabledevelop
ment.un.org/sdgs [Accessed 22 February 2017].
Weather and Climate, 2016. Available from: https://weather-and-climate.com.
Xiao, Y., et al., 2016. Object-oriented fusion of RADARSAT-2 polarimetric synthetic aperture radar
and HJ-1A multispectral data for land-cover classification. Journal of Applied Remote Sensing, 10,
026021–026021. doi:10.1117/1.JRS.10.026021
20 B. HAACK AND R. MAHABIR
Downloadedby[100.36.116.186]at04:4616November2017