3. 2 | P a g e F a b r i c s Q u a l i t y M a n u a l
Page 2 of 20 Md. Mizanur Rahman Chaity Composite Ltd
Organogram of Fabrics Quality
4. 3 | P a g e F a b r i c s Q u a l i t y M a n u a l
Page 3 of 20 Md. Mizanur Rahman Chaity Composite Ltd
Chaity Composite Ltd
Fabrics Division
Quality Assurance Department
Standard Operating Procedure
Shade Confirmation
By Shade Roll
(SF & LD)
(Ensure- Running Shade, Hairy, Uneven, Hand feel, Naps, Width & GSM)
(Wet Rub & Fastness If Required)
Start Stenter Process
Ensure Shade with Shade roll
Check online Quality
(Within 5 Rolls ensure Quality Standard)
Send to Table for Running Shade, Line /Sinker Mark
If OK as Standard If Not Ok
Finish Full Quantity Stop the Process return to
Dyeing/ Finishing
Compacting Process
Ensure Shrinkage the Adjust Parameter
Final Inspection
Light Sourcing- 1000 Lux
M/c Speed-16-18 RPM
4 Point System
Ensure- Shade, Hand feel, Surface, Width & GSM,
Width ±1 inch, GSM±5%
Ensure-
1. Shade Approval
2. Roll to roll GSM board
3. Shade Continuity (A & B)
4. Inspection Report
5. Shrinkage Report
6. Test Report
7. Packing List
8. Delivery Authorization Sign
5. 4 | P a g e F a b r i c s Q u a l i t y M a n u a l
Page 4 of 20 Md. Mizanur Rahman Chaity Composite Ltd
Job Responsibility:
Md Mizanur Rahman- AGM (Fabrics Finishing & Quality)
1. Planning & Monitoring of Delivery Target.
2. Ensure that the Quality Standard is being met by Forecasting & reviewing the result.
3. Develop Discipline, by implementing the Rules &Regulation in Department.
4. Ensure acceptable Quality level (AQL) in textile manner.
5. Give a continuous guidance to the Executive, along with others for target fabric
specification.
6. Supervision constantly to Grey & Final QC.
7. Give the full support the Research & Development Department.
8. Make a continuous study of work improvement & give report to the higher authority.
9. Response & act in the customer complain & query.
10. Ensure that all safety followed by the team.
11. Continuously study the Cost saving of the Department.
12. Enthusiastic to wastage utilization.
13. Optimize Manpower Utilization.
14. Worker Turnover & Absenteeism control as per Plan.
15. Skill Development in the Floor.
16. Ensure that all Lab test Report (Physical) are recorded.
17. Follow the concept of Top Management.
18. Regularly held a meeting to all people once in a week/ Time to time.
19. Co-ordination with all departments all quality parameter inform time to time all
department.
20.Check the hold fabric & give decision quickly.
6. 5 | P a g e F a b r i c s Q u a l i t y M a n u a l
Page 5 of 20 Md. Mizanur Rahman Chaity Composite Ltd
Senior Manager (QAD)
1. Planning & Monitoring of Delivery Target.
2. All Buyer fabrics inspection report review
3. Ensure Shade as per Customer standard
4. Fulfill the buyer wise quality requirement
5. Ensure the delivery target with Quality
6. Hold Fabric Take decision immediately
7. Ensure the 4 point system reporting
8. Grey fabric inspection & give decision
9. Ensure the test requirement
10. Ensure process loss as per standard
11. Ensure the good house keeping
12. Manpower utilizes
13. Recruited
In-charge (Shade Responsible)
1. Ensure all Shade with Standard/ SF (Batch to batch)
2. Confirm the Shade as buyer concept
3. Keep the record order wise
4. Approval taken from Merchandiser (if Needed)
5. Within short time shade confirm & Feedback to production
6. All Lab dip take from Lab Then Confirm with SF (Sample Fabrics)
7. Shade not ok keep record & Inform to Production
8. Keep all approval Swatch
Shift in-charge (Floor Inspection)
1. Ensure the four point system inspection.
2. Fulfill the delivery target with quality
3. Requirement wise delivery width, GSM shrinkage, Spirality & All Accessories (Rib,
Collar & Cuff, Back neck tap)
4. Check process loss
5. All testing confirms then delivered
6. Return for reprocess Dyeing & Finish, Keep Record & Update after Reprocess.
7. Keep Record Shrinkage & Actual GSM, Width, Process Loss in Delivery Sheet
8. Ensure the good house keeping
9. 8 | P a g e F a b r i c s Q u a l i t y M a n u a l
Page 8 of 20 Md. Mizanur Rahman Chaity Composite Ltd
Laboratory:
Lab is the head of the textile industries. Higher precision lab can aid easily to achieve the goal of
the organization. Before bulk production a sample for the approval from industry is sent to the
buyer. As per the requirement of the buyer the shade is prepared in a lab considering the
economic aspects.
Lab Line:
1. Standard sample: The buyer to the industry gives the standard sample. The sample is measured
by the CCM to get the recipe.
2. Lab trial: Getting the recipe the lab officer produces lab trial and match with standard
according to buyer requirement. Lab trial is made by the AHIBA dyeing machine. There are some
programs for dyeing. The programs are given below.
Off line Quality Control System:
ফ্যাব্রিক পব্রিদর্শন এবং পিীক্ষাগাি এবং অন্যান্য পিীক্ষা সহ Drcv`b প্রব্রিযাকিণ বন্ধ করি পিীক্ষাগাি এবং অন্যান্য Drcv`b এলাকায সঞ্চাব্রলত। পিীক্ষা
ফ্লাফ্ল অনুযাযী সংরর্াধন পদরক্ষপ গ্রহণ কিা হয।
Off-Line Tests: All the Off-Line tests for finished fabrics can be grouped as follows:
A. Physical tests
B. Chemical tests
Physical Tests:
1. GSM test
2. Shrinkage test
3. Spirality test
4. Tensile strength
5. Abrasion resistance
6. Pilling resistance
7. Button Strength Testing
8. Crease resistance
9. Dimensional stability
10. Bursting strength test
Chemical Tests:
1. Color Fastness to washing.
2. Color Fastness to light.
3. Color Fastness to heat.
4. Color Fastness to Chlorinated water.
5. Color Fastness to water spotting.
6. Color Fastness to perspiration.
7. Color Fastness to Seawater.
8. Fiber analysis.
9. PH test.
10. Repellency.
11. 10 | P a g e F a b r i c s Q u a l i t y M a n u a l
Page 10 of 20 Md. Mizanur Rahman Chaity Composite Ltd
১। 4- point system
২। 10- point system
৩। 2.5- point system etc.
আজরক 4 Point System ব্রনরয় ব্রবস্তাব্রিত আরলাচনা কিা হরব-
4 Point System প্ররয়ারগি জন্য কয ব্রবষয়গুরলা অবশ্যই প্ররয়াজন-
১। Inspection পদ্ধব্রতটি জানা থাকরত হরব।
২। কফ্ব্রিরকি ব্রবব্রভন্ন ধিরনি Defects সম্পরকশ পয শাপ্ত জ্ঞান থাকরত হরব।
৩। িাো কারলকর্রনি জন্য একটি ফ্িরমে থাকরত হরব।
4 Point System এ Fabric Inspection পদ্ধব্রত
এই পদ্ধব্রতরত Textile এি কক্ষরে প্রব্রত ১০০ গজ কাপরড়ি জন্য ব্রনব্রদ শষ্ট সংখ্যক Penalty Points এি ব্রভব্রিরত কাপরড়ি
Quality Level ব্রনধ শািণ কিা হয়। Total Penalty Point ব্রনধ শািরণি সূেটি হরে-
Total Penalty Points = (Total Points from Roll × 36 × 100)/(Fabric Length in Yards ×
Fabric Width in Inches)
4 Point System পদ্ধব্রতটি AAMA (American Apparel Manufacturers) নারমও পব্রিব্রচত। এই পদ্ধব্রতরত
কফ্ব্রিরকি Defect সাইজ ও ধিণ অনুযায়ী ১, ২, ৩ অথবা ৪ পরয়রন্ট মাব্রকশং কিা হয়।
Defect এি সাইরজি উপি ব্রভব্রি করি Penalty Point গণনাি চাে শটি ব্রনরচ কদওয়া হরলা-
Defect Size Penalty Point
৩ ইব্রঞ্চ বা তাি কম 1 Points
৩ ইব্রঞ্চি উপরি ব্রকন্তু ৬ ইব্রঞ্চি কম 2 Points
৬ ইব্রঞ্চি উপরি ব্রকন্তু ৯ ইব্রঞ্চি কম 3 Points
৯ ইব্রঞ্চ কথরক বড় 4 Points
Holes and Openings
১ ইব্রঞ্চ বা তাি কম 2 Points
১ ইব্রঞ্চি বড় 4 Points
Defect এি সাইজ কযিকমই কহাক না ককন, ব্রনব্রদ শষ্ট ১ গজ কফ্ব্রিরক সরব শাচ্চ ৪ পরয়ন্ট গণনা কিা হরব। Defect এি সাইজ
দদর্ঘ শয বা প্রস্থয সব ব্রদরকই ব্রবরবচয। পরয়ব্রন্টং কিাি কক্ষরে শুধুমাে Major Defect গুরলা ব্রবরবচনায় আসরব। Minor
Defects গুরলা ব্রবরবচনায় আসরব না।
12. 11 | P a g e F a b r i c s Q u a l i t y M a n u a l
Page 11 of 20 Md. Mizanur Rahman Chaity Composite Ltd
Major Defect এি ব্রকছু নমুনা ও তারদি Penalty Decision
কয Defect গুরলাি জন্য 4 Point System এ Penalty Point প্ররযাজয হয় কসগুরলারক Major Defect বলা হয়।
ব্রনরচ Major Defect এি ব্রকছু নমুনা কদওয়া হল।
A) সাধািণ ব্রকছু Defect
১। Spot (দাগ) ২। Knot (ব্রিঁে) ৩। Slub (স্লাব) ৪। Kink (উরটা পাক) ৫। Hole (ব্রেদ্র) ৬।
Set Mark (কসে মাকশ) ৭। Rapping (কুঁচকারনা) ৮। Cockled Yarn (পাকারনা সূতা)
B) Running Defect ( কয Defect অব্রভিাম চলরত থারক)
কয Defect অব্রভিাম চলমান থারক তারক Running Defect বরল। এ ধিরনি Defect এি জন্য কপনাব্রট পরয়ন্ট ৪ ধায শ
হরব। যব্রদ প্রব্রত ১০০ গজ কফ্ব্রিরকি প্রব্রত রুরল চলমান ৫ গজ কাপরড় এিকম Running Defect থারক তরব পুরিা Roll
কক B কগ্রি কফ্ব্রিক ব্রহরসরব ব্রবরবব্রচত হরব এবং পুরিা Roll টি Reject ব্রহরসরব ব্রবরবব্রচত হরব।
ব্রকছু Running Defect ব্রনরচ কদওয়া হরলা-
১। Lycra Out
২। Lycra Drop
৩। Needle Broken Mark
৪। Sinker Mark
৫। Machine Patta ইতযাব্রদ।
C) Uncountable Defect (কয গণনা কিা যায় না)
গণনা কিা যায় না এিকম Defect গুরলা 4 Point এি আওতায় আসরব না। এরক্ষরে পুরিা Roll টি B কগ্রি কফ্ব্রিক
ব্রহরসরব ব্রবরবব্রচত হরব এবং পুরিা Roll টি Reject ব্রহরসরব ব্রবরবব্রচত হরব।
গণনা কিা যায় না এিকম ব্রকছু Defect ব্রনরচ কদওয়া হরলা-
১। Running Shade (চলমান কালাি ব্রভন্নতা)
২। Fuzziness (কফ্ব্রিরকি উপি ক্ষুদ্র ক্ষুদ্র আঁর্)
৩। Patta (সুতাি লে ব্রমব্রি হওয়াি ফ্রল কয Defect হয়)
৪। Dia Mark (কমব্রর্রনি িায়া মাকশ)
৫। Hand Feel Problem (হারতি ের্শ খািাপ আসা)
৬। Bowing (কবাইং)
13. 12 | P a g e F a b r i c s Q u a l i t y M a n u a l
Page 12 of 20 Md. Mizanur Rahman Chaity Composite Ltd
D) Full Width Defects
কফ্ব্রিরকি প্রস্থ বিাবি একপ্রান্ত কথরক অপি প্রান্ত পয শন্ত কয Defect গুরলা জুরড় থারক কসগুরলারক Full Width Defects বরল।
১। যব্রদ প্রব্রত ১০০ গজ কফ্ব্রিরকি প্রব্রত রুরল ৬ টি Full Width Defect পাওয়া যায় তরব পুরিা Roll কক B কগ্রি কফ্ব্রিক
ব্রহরসরব ব্রবরবব্রচত হরব এবং পুরিা Roll টি Reject ব্রহরসরব ব্রবরবব্রচত হরব।
২। A কগ্রি কফ্ব্রিরকি ককান Roll এি প্রথম ও কর্ষ ব্রতন গরজ যব্রদ অন্তত ১ টি Full Width Defect পাওয়া যা তরব ঐ Roll
কক B কগ্রি কফ্ব্রিক ব্রহরসরব ব্রবরবব্রচত হরব এবং পুরিা Roll টি Reject ব্রহরসরব ব্রবরবব্রচত হরব।
৩। ককান রুলরক A কগ্রি ককায়াব্রলটি ব্রহরসরব ব্রবরবচনা কিা হরব না যব্রদ ঐ Roll এি কফ্ব্রিক ব্রিরলিালা (Baggy) প্রকৃব্রতি হয়।
কযমনঃ যব্রদ কাপরড়ি ককান অংর্ কিউ এি কদখায় (Ripple), কুঁচব্রকরয় যায় (Puckering), গভীি ভাজ পড়া (Crease and
Fold) ইতযাব্রদ।
কফ্ব্রিরকি Acceptable Level
কফ্ব্রিরকি Acceptable Level ককাম্পাব্রন এবং বায়াি অনুযায়ী ব্রভন্ন ব্রভন্ন হয়। তাই ব্রনব্রিতভারব বলা সম্ভব নয় কয কত পরয়ন্ট
হরল কফ্ব্রিক Acceptable বা Rejected হরব।
অরনক ককাম্পাব্রন কফ্ব্রিরকি ইেরপকর্ন কিজান্ট Pass বা Fail এি পব্রিবরতশ 1st Grade, 2nd Grade, 3rd Grade ইতযাব্রদ
কগ্রি করি থারক।
ব্রনরচ Roll to Roll প্রব্রত ১০০ গজ কফ্ব্রিরকি জন্য Acceptable Level এি একটি বহুল প্রচব্রলত ধািণা কদওয়া হল-
পয়েন্ট গ্রহণয় োগ্য মোত্রো গ্রগ্রড
০-২০ পরয়ন্ট A
২১-২৮ পরয়ন্ট B
২৮ এি কচরয় কবব্রর্ Reject
Fabric Type অনুযায়ী ১০০ গজ কফ্ব্রিরকি জন্য Acceptable Level এি আরিকটি প্রচব্রলত মাো ব্রনরচ কদওয়া হল-
গ্রেব্রিয়ের ধরণ পরয়ন্ট গ্রহণরযাগ্য মাো গ্রহণরযাগ্যতা
Cotton Twill/Denim ০-২৮ পরয়ন্ট Acceptable
All synthetic fabrics ০-২০ পরয়ন্ট Acceptable
প্রশ্নঃ একটি Roll এ 110 গজ কফ্ব্রিক আরে যাি Dia হরে 52 ইব্রঞ্চ । কচক কিাি সময় ব্রনরচি Defect গুরলা পাওয়া
কগরে। 4 Point System - এ ঐ Roll এি কগ্রি ব্রনণ শয় কি।
Number of Defect Defect Size
5 3.5 Inch
2 2 Inch
3 7.4 Inch
1 12.8 Inch
Holes and openings
1 Hole 3 Inch
14. 13 | P a g e F a b r i c s Q u a l i t y M a n u a l
Page 13 of 20 Md. Mizanur Rahman Chaity Composite Ltd
সমাধানঃ
কদওয়া আরে, Fabric Length = 110 গজ।
Fabric Dia বা Fabric Width = 52 ইব্রঞ্চ।
এখন, প্ররশ্ন প্রদি Defect গুরলারক সাইজ অনুযায়ী Penalty Point Table কথরক পরয়ব্রন্টং করি পাই-
Number of
Defect
Defect Size Number Of Defect × Defect Point = Penalty
Point
5 3.5 Inch 5×2 = 10
2 2 Inch 2×1 = 2
1 7.4 Inch 1×3 = 3
1 12.8 Inch 1×4 = 4
Holes and openings
1 Hole 3 Inch 1×4 = 4
Total Points 23
এখন, উপরিি তথ্যগুরলা Total Penalty Points ব্রনণ শরয়ি সুরে বব্রসরয় পাই-
Total Penalty Points = (Total Points from Roll × 36 × 100)/(Fabric Length in Yards ×
Fabric Width in Inches)
= (23×36×100)/(110×52) = 82800/5720 = 14.48
কফ্ব্রিরকি জন্য Acceptable Level কেব্রবল কথরক আমিা পাই, যব্রদ Total Penalty Points এি মান ০-২৮ হয় তাহরল
ঐ Roll টি A কগ্রি কফ্ব্রিক ব্রহরসরব ব্রবরবব্রচত হরব।
অতএব, ঐ Roll টি A কগ্রি কফ্ব্রিক।
16. 15 | P a g e F a b r i c s Q u a l i t y M a n u a l
Page 15 of 20 Md. Mizanur Rahman Chaity Composite Ltd
Shade Check in Light Box
1. Two person together shade Check Avoid the Wrong Decision. Because Two
Person Not Same Measurable Power, So combined take decision.
2. with Three Light Shade Check
3. Make Family Shade A&B
4. Light D65, TL 83, A-10 (D=daylight, TL=Tube Light, A= tungsten Filament, F=
Florescent)
5. 1
st
Batch Shade check with Standard & Counter Sample
6. Next Batch Check Batch to Batch with Counter
7. White & Grey Mélange Must be Check with UV Light
8. Metameric Check in A-10 Home Light
9. Shade Check in 45-degree Angle
Light Sourcing (Knit)
1. Shop Light (Primary) -TL83 Lax Value 1300 to more
2. Day Light (Secondary)- D65 Lax Value 1000 to More
3. Home Light - A-10 Lax Value 800 to More
4. Morning Sun Light – Ultra Violet (UV)
Light Sourcing (Under Wear)
1. Shop Light (Primary) - TL83 Lax Value 1300 to more/18w
2. Home Light (Secondary) -A-10 Lax Value 800 to More/18w
3. Day Light - D65 Lax Value 1000 to More/40w
4. Morning Sun Light – Ultra Violet (UV)/18w
17. 16 | P a g e F a b r i c s Q u a l i t y M a n u a l
Page 16 of 20 Md. Mizanur Rahman Chaity Composite Ltd
Non Conformed
Process Flow Chart of Fabric Quality
Re-process Dyeing
Stenter M/c
Shade uneven
Not OK Spot, Hairiness,
Hand feel
Lab Test
Shrinkage, Fastness &
Others
Compacting
Dia & GSM
Not OK Check
Fabrics Inspection
4 point System
Shade Continuity
Finish Fabric Store
OK
OK
18. 17 | P a g e F a b r i c s Q u a l i t y M a n u a l
Page 17 of 20 Md. Mizanur Rahman Chaity Composite Ltd
Standard Operation Procedure:
Inspection Area-
1. Grey Fabrics Inspection
2. Dyed Yarn Inspection
3. Printed Fabrics Inspection
4. After Dyeing Fabrics Inspection
Grey Fabrics Inspection-
1. 10% inspection in batch
2. Check information batch card vs bar code
3. Patta/ lycra out
4. Thick & thin
5. Hole
6. Stitch Length
Online Inspection Point
a) Shade Give to Light Box for Approved
b) Hand feel & Hairiness Check with FTD
c) 10% Rolls check table, Running Shade/Uneven
d) Naps, Hole, Patta Check, Line/Sinker Mark
e) Width & GSM confirm with Requirement
f) Within ½ inch pin in Selvage more than infirm to Finishing
g) Give to one-meter fabrics Laboratory for Test, Shrinkage/Fastness
h) Accessories available or not (Rib, Collar & Cuff)
i) Check Measurement if Required Like Stripe Fabrics
j) Information should be written in Batch Card Clearly & Online inspection Loge
book
k) If any unacceptable must be infirm to Shift In-charge
19. 18 | P a g e F a b r i c s Q u a l i t y M a n u a l
Page 18 of 20 Md. Mizanur Rahman Chaity Composite Ltd
Table Inspection Point
1. Two person together Inspection
2. Two person Maximum two hours continue inspection
3. Running Shade/ Uneven/ Hairiness
4. Hold Fabrics & Take Quick decision
5. Follow 4 point System
6. Result OK/ Reject
7. Which rolls inspection in table need identification.
8. Arrow sticker use, problematic area
9. Lux value 1000+ & Light Expired time one year or 1300 hours which is 1st valid
Compactor M/c Inspection Point
1. Two persons together Inspection
2. Two person Maximum two hours continue inspection
3. Machine Speed 16/18 RPM
4. Width & GSM check
5. Hole, Naps, Hairiness, Crease Mark, Compaction Mark, Any spot, Patta, Lycra
Missing/Out, Yarn/Fly Contra, Width Variation, Pin out, Jumping, Recovery,
Slanted, Bowing,
6. If any measurement like Stripe
7. Within ½ inch pin in Selvage more than infirm to Finishing
8. Roll to Roll Shade & GSM cut
9. Inspection as 4-point System
10. Maintain Register Loge book
11. Arrow sticker use, problematic area
12. Maintain Lux value 1000+ inspection area
20. 19 | P a g e F a b r i c s Q u a l i t y M a n u a l
Page 19 of 20 Md. Mizanur Rahman Chaity Composite Ltd
Fleece Fabric Inspection
1. Shade Check
2. Before & After Shade Check what about Change
3. Chemical Test
4. Hairiness
5. Re-tension / Stitch Recovery
6. Brush Fiber Migrations
7. Naps
8. Sinker/ Line Mark
9. GSM/ Width
Sueded Fabrics Inspection:
1. Shade Check
2. Before & After Shade Check what about Change
3. Line/ Sinker Mark
4. Naps
5. Hairiness
6. Hole before or After (Pin/ Sueded)
Yarn Dyed Inspection:-
1. Color Bleeding
2. Measurement on Stripe
3. Any fly contaminations
4. Yarn Contaminations
5. Bowing
6. Angle/ Slanted
7. Twisted/ Spirality
8. Shrinkage
Print Fabrics Inspection:
1. Check with Stranded Swatch
2. Print Durability
3. Color Bleeding
4. Before & After Check any Change
5. After Finishing print any Change
6. Shrinkage
21. 20 | P a g e F a b r i c s Q u a l i t y M a n u a l
Page 20 of 20 Md. Mizanur Rahman Chaity Composite Ltd
Procedure of Delivery (sop)-
1. Without Test Result Please don’t Delivery Any Quantity of Fabrics.
2. Without Rib/Single Jersey/ Back neck tap, not delivery.
3. Any Measurable part, Like Collar & Cuff, Stripe Yarn dyed Fabrics should be check as buyer
requirement.
4. Width ± 1”, More than need to Approval from Related Person. Also inform to cutting department.
5. Cotton Fabrics GSM ±5% & Lycra Minus 7% & Plus 3% Accepted in fabrics stage.
6. Shrinkage issue don’t consider & Spirality also
7. Before Delivery the fabrics, must be Re-check by Shift In-charge, Width, GSM, Shrinkage delivery
report with Batch information.
8. 1st Batch Shade check & crosses check for confirmation.
9. All Approved shade must be keeping before dyeing from related Merchandiser
10. All shade checks two persons avoid the wrong decision. (Keep sign)
11. 1st Batch check with Booking All information, like width, GSM, Accessories & Shade Reference.
12. Every day at 1st All delivered batches should be showing to Responsible person & take Sign
13. Unacceptable Issue doesn’t delivery & Discuss with Relative Merchandiser.
14. If any problematic fabrics need to delivery must be write down in top of the inspection report.
We have committed good quality fabrics delivery which is customer Requirement
Thanks Lots