The document discusses promoting electromagnetic processing (EP) technologies in the EU through policy measures. It makes the following key points:
1) Heating and cooling accounts for over half of Europe's energy consumption and offers significant reduction potential through electrification of industrial processes using EP technologies like induction heating.
2) Pilot projects have demonstrated EP technologies can provide energy savings of up to 75% and reduce heating times and emissions. Full adoption across energy-intensive industries could save over 13% of annual EU energy demand.
3) Targeted policy measures are needed to strengthen drivers for EP technologies and remove barriers, such as including them in the Energy Efficiency Directive, Renewable Energy Directive, and best available techniques reference
Introduction to the Ecodesign of Energy Related Products DirectiveLeonardo ENERGY
The Ecodesign of Energy Related Products Directive (EED) was adopted in 2009 as an amendment from the 2005 Ecodesign of Energy Using Products Directive and is one of the EU’s four key Directives addressing energy efficiency in stationary (i.e. non transport) end-uses (the others being the Energy Performance in Buildings Directive, Energy Efficiency Directive and the Energy Labelling Directive). The EU was a relative late comer among leading international economies in having overarching legislation to set minimum energy performance standards for equipment but since the adoption of Ecodesign it has set an impressive pace of adoption of implementing measures which are now estimated to cover 48% of all EU energy consumption. The average expected energy savings per product group addressed is projected to reach 19% by 2030, to lower energy bills by €160 billion for a €60 billion increase in equipment acquisition costs i.e. a net benefit of €100 billion and to create 0.8 million extra direct jobs for industry, wholesale and the retail sector.
The projected CO2 savings from this Directive alone are estimated to reach 320 Mt CO2 equiva-lent, equal to 7% of all EU GHG emissions in 2010. This is in excess of savings projected from the EU emissions trading system.
Second Stakeholder Event for the Revision of Directive (REDII) 2018/2001
Session 2 Renewable energy in Heating and Cooling, Buildings and District Heating
Professor Brian Vad Mathiesen, Aalborg University
March 22, 2021, Brussels - Online
Introduction to the Energy Efficiency DirectiveLeonardo ENERGY
The Energy Efficiency Directive (EED) was adopted in 2012 and is one of the EU’s four key Directives addressing energy efficiency in stationary (i.e. non transport) end-uses (the others being the Energy Performance in Buildings Directive, The Ecodesign Directive and the Energy Labelling Directive). Given that the other Directives cover the energy performance of buildings and equipment the EED is designed to address energy savings opportunities that are not readily addressed by the other Directives. It has its origin in the preceding Energy Services Directive, which was repealed when the EED was adopted. The Energy Efficiency Directive establishes a set of binding measures intended to help the EU reach its 20% energy efficiency target by 2020. Under the Directive, all EU countries are required to use energy more efficiently at all stages of the energy chain from its production to its final consumption. EU countries were required to transpose the Directive's provisions into their national laws by 5 June 2014.
The document discusses energy conservation imperatives for the aluminium foundry industry. It notes that the industry faces energy constraints and rising costs that require a 10% energy savings target. The energy conservation scheme will impose punitive tariffs for those who do not meet targets. It also examines the industry, energy needs for melting, furnace types, and the need to balance capital equipment choices with changing energy conditions.
The document summarizes the key findings from energy audits conducted at several manufacturing companies in Zambia. The audits found inefficient energy usage, including lack of energy management systems, unnecessary equipment running, and use of non-energy efficient lighting. Recommendations included establishing energy audit teams, training and awareness programs, installing efficient lighting and automated controls, improving maintenance to reduce leaks, and investing in power factor correction and quality equipment. Follow up audits and workshops were proposed to encourage energy efficiency improvements.
The document provides information about energy efficiency learnings and models in Finland. It discusses Finland's targets for 2020 related to reducing greenhouse gas emissions and increasing the share of renewables and energy efficiency. It describes the various tools Finland uses to promote energy efficiency, including legislation, subsidies, voluntary agreements and energy auditing. It also outlines the typical steps involved in energy auditing and management in Finland, and provides examples of energy savings identified in audits of industrial facilities.
This document discusses the importance of modelling energy systems with detailed representations of surrounding regions. It presents a case study comparing different levels of detail in modelling Germany's energy system within the context of surrounding countries like France, Poland, Austria and others. The study uses EnergyPLAN to model each country's system individually and also connected together. It finds that modelling with greater detail, representing each surrounding country separately rather than aggregated, reveals more nuanced results about how increased wind power in Germany may affect its own CO2 emissions versus the overall connected system's emissions. The level of geographic detail is important for policymakers and researchers to understand impacts across interconnected energy infrastructures.
This document summarizes the findings of a European Power Quality Survey conducted between 2005-2006. It interviewed representatives from key industrial sectors across 8 European countries to understand the economic impacts of poor power quality.
The study found that poor power quality, such as voltage dips, interruptions and harmonics, results in annual losses estimated at over €150 billion for the sectors surveyed. Dips and interruptions accounted for around 60% of losses. Losses were higher in manufacturing industries compared to services sectors.
Regression analysis indicated power quality related wastage was approximately 4% of annual turnover for industry and 0.14% for services. The document provides detailed methodology used to calculate different types of power quality costs from direct financial losses
Introduction to the Ecodesign of Energy Related Products DirectiveLeonardo ENERGY
The Ecodesign of Energy Related Products Directive (EED) was adopted in 2009 as an amendment from the 2005 Ecodesign of Energy Using Products Directive and is one of the EU’s four key Directives addressing energy efficiency in stationary (i.e. non transport) end-uses (the others being the Energy Performance in Buildings Directive, Energy Efficiency Directive and the Energy Labelling Directive). The EU was a relative late comer among leading international economies in having overarching legislation to set minimum energy performance standards for equipment but since the adoption of Ecodesign it has set an impressive pace of adoption of implementing measures which are now estimated to cover 48% of all EU energy consumption. The average expected energy savings per product group addressed is projected to reach 19% by 2030, to lower energy bills by €160 billion for a €60 billion increase in equipment acquisition costs i.e. a net benefit of €100 billion and to create 0.8 million extra direct jobs for industry, wholesale and the retail sector.
The projected CO2 savings from this Directive alone are estimated to reach 320 Mt CO2 equiva-lent, equal to 7% of all EU GHG emissions in 2010. This is in excess of savings projected from the EU emissions trading system.
Second Stakeholder Event for the Revision of Directive (REDII) 2018/2001
Session 2 Renewable energy in Heating and Cooling, Buildings and District Heating
Professor Brian Vad Mathiesen, Aalborg University
March 22, 2021, Brussels - Online
Introduction to the Energy Efficiency DirectiveLeonardo ENERGY
The Energy Efficiency Directive (EED) was adopted in 2012 and is one of the EU’s four key Directives addressing energy efficiency in stationary (i.e. non transport) end-uses (the others being the Energy Performance in Buildings Directive, The Ecodesign Directive and the Energy Labelling Directive). Given that the other Directives cover the energy performance of buildings and equipment the EED is designed to address energy savings opportunities that are not readily addressed by the other Directives. It has its origin in the preceding Energy Services Directive, which was repealed when the EED was adopted. The Energy Efficiency Directive establishes a set of binding measures intended to help the EU reach its 20% energy efficiency target by 2020. Under the Directive, all EU countries are required to use energy more efficiently at all stages of the energy chain from its production to its final consumption. EU countries were required to transpose the Directive's provisions into their national laws by 5 June 2014.
The document discusses energy conservation imperatives for the aluminium foundry industry. It notes that the industry faces energy constraints and rising costs that require a 10% energy savings target. The energy conservation scheme will impose punitive tariffs for those who do not meet targets. It also examines the industry, energy needs for melting, furnace types, and the need to balance capital equipment choices with changing energy conditions.
The document summarizes the key findings from energy audits conducted at several manufacturing companies in Zambia. The audits found inefficient energy usage, including lack of energy management systems, unnecessary equipment running, and use of non-energy efficient lighting. Recommendations included establishing energy audit teams, training and awareness programs, installing efficient lighting and automated controls, improving maintenance to reduce leaks, and investing in power factor correction and quality equipment. Follow up audits and workshops were proposed to encourage energy efficiency improvements.
The document provides information about energy efficiency learnings and models in Finland. It discusses Finland's targets for 2020 related to reducing greenhouse gas emissions and increasing the share of renewables and energy efficiency. It describes the various tools Finland uses to promote energy efficiency, including legislation, subsidies, voluntary agreements and energy auditing. It also outlines the typical steps involved in energy auditing and management in Finland, and provides examples of energy savings identified in audits of industrial facilities.
This document discusses the importance of modelling energy systems with detailed representations of surrounding regions. It presents a case study comparing different levels of detail in modelling Germany's energy system within the context of surrounding countries like France, Poland, Austria and others. The study uses EnergyPLAN to model each country's system individually and also connected together. It finds that modelling with greater detail, representing each surrounding country separately rather than aggregated, reveals more nuanced results about how increased wind power in Germany may affect its own CO2 emissions versus the overall connected system's emissions. The level of geographic detail is important for policymakers and researchers to understand impacts across interconnected energy infrastructures.
This document summarizes the findings of a European Power Quality Survey conducted between 2005-2006. It interviewed representatives from key industrial sectors across 8 European countries to understand the economic impacts of poor power quality.
The study found that poor power quality, such as voltage dips, interruptions and harmonics, results in annual losses estimated at over €150 billion for the sectors surveyed. Dips and interruptions accounted for around 60% of losses. Losses were higher in manufacturing industries compared to services sectors.
Regression analysis indicated power quality related wastage was approximately 4% of annual turnover for industry and 0.14% for services. The document provides detailed methodology used to calculate different types of power quality costs from direct financial losses
The sEEnergies project aims to operationalize the energy efficiency first principle (EEFP) both qualitatively and quantitatively. It will develop a decision support tool combining sector-specific energy demand models to analyze EE potentials from an energy systems perspective. Bottom-up models of buildings, transport, industry and grids will provide cost curves and potentials for EE measures. Scenarios from the EU's "A Clean Planet for All" will be used as common references. Energy system modelling will assess EEFP impacts and enable scenarios assessing synergies. A spatial model will map supply and demand and efficiency potentials. Heat Roadmap Europe provides recommendations including prioritizing savings over supply, utilizing excess heat and renewable energy in district heating, and establishing
Keynote, 15th Conference on Sustainable Development of Energy, Water and Environment Systems (SDEWES)
Brian Vad Mathiesen, Aalborg University
Online, Cologne, September 3rd 2020
The document discusses the Birmingham Centre for Environmental and Energy Economics and Management. It examines the Centre's research on various topics related to energy, the environment and economics, including: the energy efficiency of firms; why some firms are greener than others; greening business; monitoring changes in China's energy use and policies; examining hydropower in Africa; and engaging with policymakers on energy and environmental issues. The Centre brings together experts from various disciplines to provide an economic, business and social science perspective on global energy and environmental challenges.
This document discusses solar energy and solar self-consumption. It begins by covering energy sources in general before focusing on renewable vs non-renewable sources. Solar energy harnesses the sun's rays and works through photovoltaic technologies. Solar self-consumption uses on-site PV generation to meet a consumer's energy needs. The document then introduces the archeliosTM Calc software, which allows for calculation, sizing and control of self-consumption PV installations.
This webinar analyses energy efficiency trends in the EU for the period 2014-2019 and the impact of COVID-19 in 2020 (based on estimates from Enerdata).
The speakers present the overall trend in total energy supply and in final energy consumption, as well as details by sector, alongside macro-economic data. They will explain the main drivers of the variation in energy consumption since 2014 and determine the impact of energy savings.
Speakers:
Laura Sudries, Senior Energy Efficiency Analyst, Enerdata
Bruno Lapillonne, Scientific Director, Enerdata
The recordings of the presentation (webinar) can be viewed at:
https://youtu.be/8RuK5MroTxk
This document is a student assignment on energy policy and economics that analyzes installing a combined heat and power (CHP) system for a manufacturing plant. It includes an introduction on energy policies, a feasibility evaluation of the plant's energy needs, an analysis of the costs and emissions reductions of a CHP system compared to the plant's current electricity and heating sources, and a payback calculation showing the CHP system would pay for itself in under 2 years. Key details provided include the plant's electrical and thermal load requirements, current energy costs, specifications of the proposed CHP system, estimated costs and savings, and reductions in CO2 and other emissions.
The document summarizes India's renewable energy initiatives by the government. It discusses the various renewable energy sources including solar, wind, and biomass. It outlines the government authorities promoting renewable energy and provides details on solar and wind energy potential and production in India. It also discusses the incentives and subsidies provided by the government for different renewable energy projects and research and development efforts in the sector.
Auctions for Renewable Energy – Model based AnalysisLeonardo ENERGY
Auctions are increasingly being applied as a mechanism to allocate support to renewable energy sources (RES). AURES (Auctions for Renewable Energy Support) is a H2020 European research project focused on auction designs for renewable energy support. The project addresses the important and urgent issue of improving current support policies for electricity from renewable energy sources through competitive market measures. The general objective of the project is to promote an effective use and efficient implementation of auctions for renewable energy support in the European Union Member States, especially regarding their cost-efficiency.
In this new webinar series, the AURES team will share research results and provide guidance to policy makers on the best options to organize renewables support under the new rules of the Clean Energy Package.
Towards a systems approach in Ecodesign and Energy Labelling: How to make the...Leonardo ENERGY
This document discusses moving towards a systems approach in ecodesign and energy labelling regulations. It provides an overview of some challenges in regulating systems compared to individual products, including assessing system efficiency, identifying responsible parties, and challenges for market surveillance authorities. Examples of studies on specific systems like heating/water heating packages, lighting systems, and pumps are mentioned. Views from the EU Commission emphasize that ecodesign regulations currently apply to individual goods placed on the market, but can also cover systems if they are put together on location. Moving towards more systems approaches could increase energy savings but also introduces complexity around testing, compliance, and enforcement.
Combining renewable and traditional energy solutionsBusiness Finland
This document discusses renewable and traditional energy solutions presented at a Zambia-Finland energy workshop. It summarizes biomass, solar, renewable hybrid solutions, waste-to-energy, and co-firing options. Biomass technologies can convert agricultural waste, animal waste, and sludge into energy. Solar power is abundant in Zambia and large solar parks and concentrated solar plants could power remote areas and industries. Hybrid renewables solutions combine different renewable sources. Waste-to-energy, like gasification, is a sustainable way to dispose of waste and generate energy. Co-firing biomass and coal in power plants can reduce emissions while extending coal supplies. VTT offers technologies related to thermochemical energy
Flyer accompanying the recent WWF study "Blueprint Germany - A Strategy for a Climate Safe 2050". The study answers the question how to cut 95% greenhouse gases in Germany by 2050 and provides a concrete policy programme for this
purpose.
Energy efficiency trends in transport in the EULeonardo ENERGY
After 6 years of regular decrease, the energy consumption of transport in the EU has been rising again since 2013, at the same rate as before the financial crisis. It has become the most energy-consuming end-use sector, responsible for 31% of the final energy consumption in the EU27 in 2019. The energy transition in transport lags far behind the other sectors. However, some countries are performing better than others.
During this webinar, our expert speakers present an evaluation of the energy efficiency trend in the European transport sector since 2000. The following key questions are addressed:
What has been the overall trend in transport energy consumption in the EU and other European countries since 2000?
What are the main drivers for the energy consumption variation in transport, and in particular for the energy savings?
Recordings of the webinar: https://youtu.be/3TbePJCDvgE
The IEA Energy Efficiency Market report - What it means for DSMLeonardo ENERGY
The Energy Efficiency Market Report is the IEA’s flagship report on energy efficiency trends around the world.
Questions addressed in this year’s report include: Are we improving energy efficiency fast enough to achieve our climate goals? Which countries and policies are having the greatest impact and what is the secret to their success? How much is being invested in energy efficiency globally, in specific regions and in the main energy-consuming sectors? How are low energy prices impacting energy efficiency investments? What are the multiple benefits of energy efficiency for the climate, energy security and public budgets? What are the market trends for energy efficiency services and financing?
Speaker for this webinar: Tyler Bryant
Philipp Steinberg - La transición energética en Europa y el cambio climáticoFundación Ramón Areces
Entre el 30 de junio y el 2 de julio de 2014 organizamos en la Fundación Ramón Areces (C/ Vitruvio, 5, en Madrid) un curso de verano en colaboración con la Universidad Complutense de Madrid sobre los retos energéticos de Europa ante el cambio climático. En estas jornadas, diferentes expertos analizaron la transición energética en Europa para cumplir las exigencias de los compromisos internacionales en materia de emisiones de CO2.
Aalto Global Impact organized together with the New Global an event called Co-creating Business Ecosystems in Emerging Markets on 17th of June. The event was hosted by Fortum.
Energy Storage Training shows you the fundamentals of energy storage, future capability of energy storage, and diverse utilizations of energy storage in current world.
It is estimated that energy storage frameworks showcase will reach to 16 Billion by 2020. With expanding number of sustainable power source establishments, electric vehicle market, and advances in energy storage advertise in various applications, legitimate training is expected to enhance your insight into energy storage and distinctive advances or applications identified with present day energy storage frameworks in this day and age.
Audience:
3-day course designed for:
All professionals in the area of energy storage systems
Non-engineers looking to understand new approaches of storing energy
Individuals who are looking for technical training of energy storage systems
Project managers, quality managers, business managers and directors looking for a comprehensive training in energy storage application and operation
Energy storage producers who look for alternatives to improve their energy storage design and efficiency
Executives and managers who are looking to invest in energy storage area
Investors and contractors who plan to make investments in energy storage industry.
Technicians, operators, and maintenance personnel who are or will be working on energy storage projects
Training Objectives:
Understand Fundamentals of batteries and concept of storing energy
Understand the materials used in different types of energy storage and to recognize the operation
Recognize the parameters that control energy storage performance
Describe different application of energy storage in electrical engineering
Explain different application of energy storage in ground, air, or marine transportation systems
Understand the application of energy storage in photovoltaic
Troubleshoot challenges related to energy storage systems
Describe super capacitors, and their applications in the system
Differentiate thermal and hydrogen storage
Understand the fuel cells and different applications and types of fuel cells in the system
Training Outline:
Introduction to Energy Storage Systems
Energy Storage in Electrical Engineering
Energy Storage in Transportation
Energy Storage in Photovoltaic Systems
Energy Storage in Mobile Applications and Micro-Power Sources
Hydrogen and Thermal Storage
Lead Acid Batteries
Fuel Cells Principles
Electrochemical Storage
Super Capacitors
Hands On, Workshops and Group Activities
Sample Workshops and Labs for Energy Storage Training
Request More Information About Energy Storage Training
https://www.tonex.com/training-courses/energy-storage-training/
Lessons learnt from the EEA catalogue of environment and climate policy evalu...Leonardo ENERGY
The EEA catalogue of environment and climate policy evaluations is a database of about 600 evaluations. This webinar will present the objectives and contents of this catalogue, how it has been developed and what lessons can be learnt from this compilation.
Presentation by Nis Bertelsen at IRENA event "Integration of Low-Temperature Renewable Energy Sources into District Heating and Cooling Systems" in Belgrade 05-06 Dec 2019.
Energy efficiency trends in the EU: Have we got off track?Diedert Debusscher
What has been the overall trend in final energy consumption and by sector in the EU since 2000? What are the main drivers of the energy consumption variation since 2000, and what has been the impact of energy savings? What are the trends in energy efficiency at the country level?
These are the key questions that will guide you through this webinar analysing energy efficiency trends in the EU for the period 2000-2019.
This presentation deck was used during the 9th webinar in the Odyssee-Mure on Energy Efficiency Academy on 25 June 2020. Recordings are available on https://www.youtube.com/user/LeonardoENERGY/videos?view=0&sort=dd&flow=grid
The webinar is an approximately 45 min presentation, followed by a live Q&A session with the panellists.
Industrial Value Chains - A Bridge Towards a climate neutral EuropeTomas Wyns
This document discusses the role of energy intensive industries (EIIs) in achieving a carbon neutral Europe. It profiles EIIs and their contributions to emissions reductions. It outlines various technological solutions and business models being developed. It also discusses the framework conditions needed, including investment challenges, infrastructure needs, and regulatory barriers. Finally, it calls for a new industrial strategy with missions for research and demonstration, alignment of energy and industry policies, financing mechanisms, infrastructure planning, and smart regulations to support the transition to low-carbon industries.
Keeping our cities sustainably warm - Inspiring the Efficient Renewal of District Heating for the Just Transition
Brian Vad Mathiesen, Aalborg University
KeepWarm Conference, November 12, 2020, Brussels - Online
The sEEnergies project aims to operationalize the energy efficiency first principle (EEFP) both qualitatively and quantitatively. It will develop a decision support tool combining sector-specific energy demand models to analyze EE potentials from an energy systems perspective. Bottom-up models of buildings, transport, industry and grids will provide cost curves and potentials for EE measures. Scenarios from the EU's "A Clean Planet for All" will be used as common references. Energy system modelling will assess EEFP impacts and enable scenarios assessing synergies. A spatial model will map supply and demand and efficiency potentials. Heat Roadmap Europe provides recommendations including prioritizing savings over supply, utilizing excess heat and renewable energy in district heating, and establishing
Keynote, 15th Conference on Sustainable Development of Energy, Water and Environment Systems (SDEWES)
Brian Vad Mathiesen, Aalborg University
Online, Cologne, September 3rd 2020
The document discusses the Birmingham Centre for Environmental and Energy Economics and Management. It examines the Centre's research on various topics related to energy, the environment and economics, including: the energy efficiency of firms; why some firms are greener than others; greening business; monitoring changes in China's energy use and policies; examining hydropower in Africa; and engaging with policymakers on energy and environmental issues. The Centre brings together experts from various disciplines to provide an economic, business and social science perspective on global energy and environmental challenges.
This document discusses solar energy and solar self-consumption. It begins by covering energy sources in general before focusing on renewable vs non-renewable sources. Solar energy harnesses the sun's rays and works through photovoltaic technologies. Solar self-consumption uses on-site PV generation to meet a consumer's energy needs. The document then introduces the archeliosTM Calc software, which allows for calculation, sizing and control of self-consumption PV installations.
This webinar analyses energy efficiency trends in the EU for the period 2014-2019 and the impact of COVID-19 in 2020 (based on estimates from Enerdata).
The speakers present the overall trend in total energy supply and in final energy consumption, as well as details by sector, alongside macro-economic data. They will explain the main drivers of the variation in energy consumption since 2014 and determine the impact of energy savings.
Speakers:
Laura Sudries, Senior Energy Efficiency Analyst, Enerdata
Bruno Lapillonne, Scientific Director, Enerdata
The recordings of the presentation (webinar) can be viewed at:
https://youtu.be/8RuK5MroTxk
This document is a student assignment on energy policy and economics that analyzes installing a combined heat and power (CHP) system for a manufacturing plant. It includes an introduction on energy policies, a feasibility evaluation of the plant's energy needs, an analysis of the costs and emissions reductions of a CHP system compared to the plant's current electricity and heating sources, and a payback calculation showing the CHP system would pay for itself in under 2 years. Key details provided include the plant's electrical and thermal load requirements, current energy costs, specifications of the proposed CHP system, estimated costs and savings, and reductions in CO2 and other emissions.
The document summarizes India's renewable energy initiatives by the government. It discusses the various renewable energy sources including solar, wind, and biomass. It outlines the government authorities promoting renewable energy and provides details on solar and wind energy potential and production in India. It also discusses the incentives and subsidies provided by the government for different renewable energy projects and research and development efforts in the sector.
Auctions for Renewable Energy – Model based AnalysisLeonardo ENERGY
Auctions are increasingly being applied as a mechanism to allocate support to renewable energy sources (RES). AURES (Auctions for Renewable Energy Support) is a H2020 European research project focused on auction designs for renewable energy support. The project addresses the important and urgent issue of improving current support policies for electricity from renewable energy sources through competitive market measures. The general objective of the project is to promote an effective use and efficient implementation of auctions for renewable energy support in the European Union Member States, especially regarding their cost-efficiency.
In this new webinar series, the AURES team will share research results and provide guidance to policy makers on the best options to organize renewables support under the new rules of the Clean Energy Package.
Towards a systems approach in Ecodesign and Energy Labelling: How to make the...Leonardo ENERGY
This document discusses moving towards a systems approach in ecodesign and energy labelling regulations. It provides an overview of some challenges in regulating systems compared to individual products, including assessing system efficiency, identifying responsible parties, and challenges for market surveillance authorities. Examples of studies on specific systems like heating/water heating packages, lighting systems, and pumps are mentioned. Views from the EU Commission emphasize that ecodesign regulations currently apply to individual goods placed on the market, but can also cover systems if they are put together on location. Moving towards more systems approaches could increase energy savings but also introduces complexity around testing, compliance, and enforcement.
Combining renewable and traditional energy solutionsBusiness Finland
This document discusses renewable and traditional energy solutions presented at a Zambia-Finland energy workshop. It summarizes biomass, solar, renewable hybrid solutions, waste-to-energy, and co-firing options. Biomass technologies can convert agricultural waste, animal waste, and sludge into energy. Solar power is abundant in Zambia and large solar parks and concentrated solar plants could power remote areas and industries. Hybrid renewables solutions combine different renewable sources. Waste-to-energy, like gasification, is a sustainable way to dispose of waste and generate energy. Co-firing biomass and coal in power plants can reduce emissions while extending coal supplies. VTT offers technologies related to thermochemical energy
Flyer accompanying the recent WWF study "Blueprint Germany - A Strategy for a Climate Safe 2050". The study answers the question how to cut 95% greenhouse gases in Germany by 2050 and provides a concrete policy programme for this
purpose.
Energy efficiency trends in transport in the EULeonardo ENERGY
After 6 years of regular decrease, the energy consumption of transport in the EU has been rising again since 2013, at the same rate as before the financial crisis. It has become the most energy-consuming end-use sector, responsible for 31% of the final energy consumption in the EU27 in 2019. The energy transition in transport lags far behind the other sectors. However, some countries are performing better than others.
During this webinar, our expert speakers present an evaluation of the energy efficiency trend in the European transport sector since 2000. The following key questions are addressed:
What has been the overall trend in transport energy consumption in the EU and other European countries since 2000?
What are the main drivers for the energy consumption variation in transport, and in particular for the energy savings?
Recordings of the webinar: https://youtu.be/3TbePJCDvgE
The IEA Energy Efficiency Market report - What it means for DSMLeonardo ENERGY
The Energy Efficiency Market Report is the IEA’s flagship report on energy efficiency trends around the world.
Questions addressed in this year’s report include: Are we improving energy efficiency fast enough to achieve our climate goals? Which countries and policies are having the greatest impact and what is the secret to their success? How much is being invested in energy efficiency globally, in specific regions and in the main energy-consuming sectors? How are low energy prices impacting energy efficiency investments? What are the multiple benefits of energy efficiency for the climate, energy security and public budgets? What are the market trends for energy efficiency services and financing?
Speaker for this webinar: Tyler Bryant
Philipp Steinberg - La transición energética en Europa y el cambio climáticoFundación Ramón Areces
Entre el 30 de junio y el 2 de julio de 2014 organizamos en la Fundación Ramón Areces (C/ Vitruvio, 5, en Madrid) un curso de verano en colaboración con la Universidad Complutense de Madrid sobre los retos energéticos de Europa ante el cambio climático. En estas jornadas, diferentes expertos analizaron la transición energética en Europa para cumplir las exigencias de los compromisos internacionales en materia de emisiones de CO2.
Aalto Global Impact organized together with the New Global an event called Co-creating Business Ecosystems in Emerging Markets on 17th of June. The event was hosted by Fortum.
Energy Storage Training shows you the fundamentals of energy storage, future capability of energy storage, and diverse utilizations of energy storage in current world.
It is estimated that energy storage frameworks showcase will reach to 16 Billion by 2020. With expanding number of sustainable power source establishments, electric vehicle market, and advances in energy storage advertise in various applications, legitimate training is expected to enhance your insight into energy storage and distinctive advances or applications identified with present day energy storage frameworks in this day and age.
Audience:
3-day course designed for:
All professionals in the area of energy storage systems
Non-engineers looking to understand new approaches of storing energy
Individuals who are looking for technical training of energy storage systems
Project managers, quality managers, business managers and directors looking for a comprehensive training in energy storage application and operation
Energy storage producers who look for alternatives to improve their energy storage design and efficiency
Executives and managers who are looking to invest in energy storage area
Investors and contractors who plan to make investments in energy storage industry.
Technicians, operators, and maintenance personnel who are or will be working on energy storage projects
Training Objectives:
Understand Fundamentals of batteries and concept of storing energy
Understand the materials used in different types of energy storage and to recognize the operation
Recognize the parameters that control energy storage performance
Describe different application of energy storage in electrical engineering
Explain different application of energy storage in ground, air, or marine transportation systems
Understand the application of energy storage in photovoltaic
Troubleshoot challenges related to energy storage systems
Describe super capacitors, and their applications in the system
Differentiate thermal and hydrogen storage
Understand the fuel cells and different applications and types of fuel cells in the system
Training Outline:
Introduction to Energy Storage Systems
Energy Storage in Electrical Engineering
Energy Storage in Transportation
Energy Storage in Photovoltaic Systems
Energy Storage in Mobile Applications and Micro-Power Sources
Hydrogen and Thermal Storage
Lead Acid Batteries
Fuel Cells Principles
Electrochemical Storage
Super Capacitors
Hands On, Workshops and Group Activities
Sample Workshops and Labs for Energy Storage Training
Request More Information About Energy Storage Training
https://www.tonex.com/training-courses/energy-storage-training/
Lessons learnt from the EEA catalogue of environment and climate policy evalu...Leonardo ENERGY
The EEA catalogue of environment and climate policy evaluations is a database of about 600 evaluations. This webinar will present the objectives and contents of this catalogue, how it has been developed and what lessons can be learnt from this compilation.
Presentation by Nis Bertelsen at IRENA event "Integration of Low-Temperature Renewable Energy Sources into District Heating and Cooling Systems" in Belgrade 05-06 Dec 2019.
Energy efficiency trends in the EU: Have we got off track?Diedert Debusscher
What has been the overall trend in final energy consumption and by sector in the EU since 2000? What are the main drivers of the energy consumption variation since 2000, and what has been the impact of energy savings? What are the trends in energy efficiency at the country level?
These are the key questions that will guide you through this webinar analysing energy efficiency trends in the EU for the period 2000-2019.
This presentation deck was used during the 9th webinar in the Odyssee-Mure on Energy Efficiency Academy on 25 June 2020. Recordings are available on https://www.youtube.com/user/LeonardoENERGY/videos?view=0&sort=dd&flow=grid
The webinar is an approximately 45 min presentation, followed by a live Q&A session with the panellists.
Industrial Value Chains - A Bridge Towards a climate neutral EuropeTomas Wyns
This document discusses the role of energy intensive industries (EIIs) in achieving a carbon neutral Europe. It profiles EIIs and their contributions to emissions reductions. It outlines various technological solutions and business models being developed. It also discusses the framework conditions needed, including investment challenges, infrastructure needs, and regulatory barriers. Finally, it calls for a new industrial strategy with missions for research and demonstration, alignment of energy and industry policies, financing mechanisms, infrastructure planning, and smart regulations to support the transition to low-carbon industries.
Keeping our cities sustainably warm - Inspiring the Efficient Renewal of District Heating for the Just Transition
Brian Vad Mathiesen, Aalborg University
KeepWarm Conference, November 12, 2020, Brussels - Online
The document discusses the key elements of EU energy policy, which aims to ensure affordable, secure, and sustainable energy for Europeans. It outlines several major challenges, including climate change, import dependency, and the need for infrastructure investment. The policy focuses on energy efficiency, completing the internal energy market, energy security, decarbonization through emissions trading and renewable investment, and research and development including the Strategic Energy Technology Plan. The overall goals are to reduce greenhouse gas emissions 20% by 2020, increase renewable energy to 20% of consumption, and improve energy efficiency 20%, as part of a long-term strategy to transform Europe's energy system.
The document summarizes a Clean Day 2015 event in Beijing that will allow Finnish cleantech companies to meet with Chinese authorities regulating the energy sector and some of the largest ESCO companies in China. It provides an agenda for seminars on November 16-18, including presentations by Chinese officials on China's energy sector and by Finnish companies. It also summarizes a report on 46 major Chinese ESCO companies representing sectors like iron/steel, pulp/paper, and chemicals. These ESCOs have invested billions in energy efficiency in recent years and are interested in technologies like waste heat recovery and variable frequency drives. The event will include company visits on the final day.
This document discusses Combined Heat and Power (CHP) production and its advantages. It notes that CHP is an efficient use of resources that can produce both electricity and heat from one fuel source. CHP has significant global potential for growth, as it can utilize various renewable and waste fuels flexibly at both large and small scales. The document also discusses Fortum's strategy and vision, with CHP playing a key role. Fortum has many existing CHP plants and is constructing a new one in Klaipėda, Lithuania to provide heat and electricity using local biofuels and waste in a sustainable manner.
Smart energy efficiency for industrial consumer systemsGeorges Seil, PhD
Georges Seil is an energy efficiency expert who has worked on projects in Europe and obtained certifications in energy management. He proposes a method called FEEBIZ that breaks down industrial energy consumption into finite elements that can each be optimized. The document discusses threats to energy efficiency, trends like ISO 50001 energy management, and investment opportunities in waste-to-energy conversion technologies like pyrolysis of plastics and tires. On-site combined heat and power is also presented as an efficient option to improve industrial energy use.
Smart energy efficiency for industrial consumer systemsGeorges Seil, PhD
Georges Seil is an energy efficiency expert who has worked on projects in Europe and obtained certifications in energy management. He proposes a method called FEEBIZ that breaks down industrial energy consumption into finite elements that can each be optimized. The document discusses threats to energy efficiency, trends like ISO 50001 energy management, and investment opportunities in waste-to-energy conversion technologies like pyrolysis of plastics and tires. On-site combined heat and power is also presented as an efficient option to improve industrial energy use.
The Scope for Energy Saving in the EU through the Use of Energy-Efficient Dis...Leonardo ENERGY
Highlights:
* Distribution transformers represent an important focus for energy efficiency initiatives.
* They are a worthwhile area for R&D, demonstration and promotional effort.
* The potential for reducing losses from distribution transformers affects strategies on energy efficiency and global warming.
* An action plan should be developed to achieve these goals.
* The strategy should be carefully co-ordinated, technically sound, and involve partners from all the supply chain.
Renewable heating technologies provide an important opportunity for UK businesses and consumers to reduce energy bills and carbon emissions. Heating accounts for over 78% of energy usage in homes and 55% of non-domestic buildings, and produces 38% of UK carbon emissions. However, awareness and understanding of renewable heating solutions like biomass boilers and heat pumps is currently low in the UK. Increased education is needed to help households and businesses recognize these proven technologies as modern, efficient alternatives to fossil fuel heating.
The document discusses a workshop on energy optimisation to be held in Port Harcourt, Nigeria from November 29th to December 2nd 2022. It defines energy optimisation and energy efficiency, and explains their importance in reducing energy costs, carbon emissions, and climate impacts. It provides tips on optimising energy like shutting down computers and using power strips, and discusses energy labels, ratings, policies, and optimising combustion in boilers.
Future Electricity Markets: key pillars with high shares of wind and PVLeonardo ENERGY
More and more countries world-wide are targeting high shares of wind and solar photovoltaics in their electricity mix. To integrate high shares of these variable renewable energy sources, the electricity system needs to become more flexible in order to balance supply and demand at all times. The webinar will discuss key design features of future electricity markets, including incentives for more flexible fossil-fuel based and renewable-based power generation, modifications to the design of electricity markets, incentives for more flexible demand, and storage options.
Future electricity markets: key pillars with high shares of wind and PVLeonardo ENERGY
This session is part of the Clean Energy Regulators Initiative Webinar Programme.
Theme 4 - Integration and Issues for Renewables
Module 3: Key pillars of electricity markets with high shares of wind and PV
More and more countries world-wide are targeting high shares of wind and solar photovoltaics in their electricity mix. To integrate high shares of these variable renewable energy sources, the electricity system needs to become more flexible in order to balance supply and demand at all times. The webinar will discuss key design features of future electricity markets, including incentives for more flexible fossil-fuel based and renewable-based power generation, modifications to the design of electricity markets, incentives for more flexible demand, and storage options.
English language version of the presentation given by Jonathan Jutsen, Chairman of the Australian Alliance for Energy Productivity in San Luis Argentina in December 2016
Delivered by Roberto Francia, MD of COGEN Europe, at the COGEN Vlaanderen annual conference "15 jaar COGEN: Tijd om vooruit te blikken!". Leuven, 17 May 2016.
Similar to Promoting an EU Agenda for Electromagnetic Processing of Materials (20)
A new generation of instruments and tools to monitor buildings performanceLeonardo ENERGY
What is the added value of monitoring the flexibility, comfort, and well-being of a building? How can occupants be better informed about the performance of their building? And how to optimize a building's maintenance?
The slides were presented during a webinar and roundtable with a focus on a new generation of instruments and tools to monitor buildings' performance, and their link with the Smart Readiness Indicator (SRI) for buildings as introduced in the EU's Energy Performance of Buildings Directive (EPBD).
Link to the recordings: https://youtu.be/ZCFhmldvRA0
Addressing the Energy Efficiency First Principle in a National Energy and Cli...Leonardo ENERGY
When designing energy and climate policies, EU Member States have to apply the Energy Efficiency First Principle: priority should be given to measures reducing energy consumption before other decarbonization interventions are adopted. This webinar summarizes elements of the energy and climate policy of Cyprus illustrating how national authorities have addressed this principle so far, and outline challenges towards its much more rigorous implementation that is required in the coming years.
Auctions for energy efficiency and the experience of renewablesLeonardo ENERGY
Auctions are an emerging market-based policy instrument to promote energy efficiency that has started to gain traction in the EU and worldwide. This presentation provides an overview and comparison of several energy efficiency auctions and derives conclusions on the effects of design elements based on auction theory and on experiences of renewable energy auctions. We include examples from energy efficiency auctions in Brazil, Canada, Germany, Portugal, Switzerland, Taiwan, UK, and US.
A recording of this presentation can be viewed at:
https://youtu.be/aC0h4cXI9Ug
Energy efficiency first – retrofitting the building stock finalLeonardo ENERGY
Retrofitting the building stock is a challenging undertaking in many respects - including costs. Can it nevertheless qualify as a measure under the Energy Efficiency First principle? Which methods can be applied for the assessment and what are the results in terms of the cost-effectiveness of retrofitting the entire residential building stock? How do the results differ for minimization of energy use, CO2 emissions and costs? And which policy conclusions can be drawn?
This presentation was used during the 18th webinar in the Odyssee-Mure on Energy Efficiency Academy on February 3, 2022.
A link to the recording: https://youtu.be/4pw_9hpA_64
How auction design affects the financing of renewable energy projects Leonardo ENERGY
Recording available at https://youtu.be/lPT1o735kOk
Renewable energy auctions might affect the financing of renewable energy (RE) projects. This webinar presents the results of the AURES II project exploring this topic. It discusses how auction designs ranging from bid bonds to penalties and remuneration schemes impact financing and discusses creating a low-risk auction support framework.
This presentation discusses the contribution of Energy Efficiency Funds to the financing of energy efficiency in Europe. The analysis is based on the MURE database on energy efficiency policies. As an example, the German Energy Efficiency Fund is described in more detail.
This is the 17th webinar in the Odyssee-Mure on Energy Efficiency Academy.
Recordings are available on: https://youtu.be/KIewOQCgQWQ
(see updated version of this presentation:
https://www.slideshare.net/sustenergy/energy-efficiency-funds-in-europe-updated)
The Energy Efficiency First Principle is a key pillar of the European Green Deal. A prerequisite for its widespread application is to secure financing for energy efficiency investments.
This presentation discusses the contribution of Energy Efficiency Funds to the financing of energy efficiency in Europe. The analysis is based on the MURE database on energy efficiency policies. As an example, the German Energy Efficiency Fund is described in more detail.
This is the 17th webinar in the Odyssee-Mure on Energy Efficiency Academy.
Recordings are available on: https://youtu.be/KIewOQCgQWQ
Five actions fit for 55: streamlining energy savings calculationsLeonardo ENERGY
During the first year of the H2020 project streamSAVE, multiple activities were organized to support countries in developing savings estimations under Art.3 and Art.7 of the Energy Efficiency Directive (EED).
A fascinating output of the project so far is the “Guidance on Standardized saving methodologies (energy, CO2 and costs)” for a first round of five so-called Priority Actions. This Guidance will assist EU member states in more accurately calculating savings for a set of new energy efficiency actions.
This webinar presents this Guidance and other project findings to the broader community, including industry and markets.
AGENDA
14:00 Introduction to streamSAVE
(Nele Renders, Project Coordinator)
14:10 Views from the EU Commission and the link with Fit-for-55 (Anne-Katherina Weidenbach, DG ENER)
14:20 The streamSAVE guidance and its platform illustrated (Elisabeth Böck, AEA)
14:55 A view from industry: What is the added value of streamSAVE (standardized) methods in frame of the EED (Conor Molloy, AEMS ECOfleet)
14:55 Country experiences: the added value of standardized methods (Elena Allegrini, ENEA, Italy)
The recordings of the webinar can be found on https://youtu.be/eUht10cUK1o
Energy and mobility poverty: Will the Social Climate Fund be enough to delive...Leonardo ENERGY
Prior to the current soaring energy prices across Europe, the European Commission proposed, as part of the FitFor55 climate and energy package, the EU Social Climate Fund to mitigate the expected social impact of extending the EU ETS to transport and heating.
The report presented in this webinar provides an update of the European Energy Poverty Index, published for the first time in 2019, which shows the combined effect of energy and mobility poverty across Member States. Beyond the regular update of the index, the report provides analysis of the existing EU policy framework related to energy and transport poverty. France is used as a case study given the “yellow vest” movement, which was triggered by the proposed carbon tax on fuels.
Watch the recordings of the webinar:
https://youtu.be/i1Jdd3H05t0
Does the EU Emission Trading Scheme ETS Promote Energy Efficiency?Leonardo ENERGY
This policy brief analyzes the main interacting mechanisms between the Energy Efficiency Directive (EED) and the EU Emission Trading Scheme (ETS). It presents a detailed top-down approach, based on the ODYSSEE energy indicators, to identify energy savings from the EU ETS.
The main task consists in isolating those factors that contribute to the change in energy consumption of industrial branches covered by the EU ETS, and the energy transformation sector (mainly the electricity sector).
Speaker:
Wolfgang Eichhammer (Head of the Competence Center Energy Policy and Energy Markets @Fraunhofer Institute for Systems and Innovation Research ISI)
The recordings of this webinar can be watched via:
https://youtu.be/TS6PxIvtaKY
Energy efficiency, structural change and energy savings in the manufacturing ...Leonardo ENERGY
- Structural changes in manufacturing have significantly reduced energy consumption in Denmark since 1990 through growth in lower intensity sectors like food production.
- Energy efficiency improvements also contributed, especially from 2010-2014, lowering consumption alongside structural changes.
- A decomposition analysis found that decreases in consumption from 2006-2014 were mainly from structural effects in the first half, and efficiency gains in the latter half.
- Reported energy savings from Denmark's energy efficiency obligation scheme align with estimated efficiency improvements, though some autonomous gains likely occurred too.
Energy Sufficiency Indicators and Policies (Lea Gynther, Motiva)Leonardo ENERGY
This policy brief looks at questions ‘how to measure energy sufficiency’, ‘which policies and measures can be used to address energy sufficiency’ and ‘how they are used in Europe today’.
Energy sufficiency refers to a situation where everyone has access to the energy services they need, whilst the impacts of the energy system do not exceed environmental limits. The level of ambition needed to address energy sufficiency is higher than in the case of energy efficiency.
This is the 13th edition of the Odyssee-Mure on Energy Efficiency Academy, and number 519 in the Leonardo ENERGY series. The recording of the live presentation can be found on https://www.youtube.com/watch?v=jEAdYbI0wDI&list=PLUFRNkTrB5O_V155aGXfZ4b3R0fvT7sKz
The Super-efficient Equipment and Appliance Deployment (SEAD) Initiative Prod...Leonardo ENERGY
The Super-efficient Equipment and Appliance Deployment (SEAD) Initiative Product Efficiency Call to Action, by Melanie Slade - IEA and Nicholas Jeffrey - UK BEIS
Breuckmann eMobility GmbH develops innovative rotor casting technology called Zero Porosity Rotor (ZPR) for electric vehicle induction motors. ZPR uses laminar squeeze casting to produce rotors with zero porosity, allowing for superior mechanical properties, higher electrical conductivity, and maximum process stability compared to industry standard rotors. Key advantages of ZPR rotors include up to 12.5% higher maximum rotational speed, 35% higher electrical conductivity, and ability to withstand 25% higher circumferential bursting speeds. Breuckmann has partnerships for motor testing, slot geometry design, and received EU funding to develop high-speed motor concepts using its ZPR technology.
dynamic E flow GmbH provides high-tech electric machines and solutions for extreme applications. Their capcooltech® motor features direct winding cooling that enables current densities up to 100A/mm2 and overload capacities. Testing shows the capcooltech® design maintains temperatures 40°C lower and heats 10 times faster than conventional cooling. The direct cooling test bench demonstrates capcooltech® motors can achieve maximum power density, temperature resistance, precision, and dynamics even in harsh conditions like vacuum or high temperatures.
The need for an updated European Motor Study - key findings from the 2021 US...Leonardo ENERGY
The document calls for an updated assessment of the electric motor system market in Europe, as the existing data is over 20 years old. It notes several changes in the market since then, including new efficient motor technologies, lower costs for power electronics, and increased digitization. The document highlights findings from a recent 2021 US motor study, which found motors to be older than previously estimated and significant improvements in load factors and variable speed drive penetration compared to past studies. It concludes that a new comprehensive assessment is needed to identify large potential electricity savings and inform policies to accelerate market transformation.
Efficient motor systems for a Net Zero world, by Conrad U. Brunner - Impact E...Leonardo ENERGY
1) The document discusses the need for efficient electric motor systems to achieve net-zero emissions by 2050, as electricity will be the main energy supplier without fossil fuels or nuclear.
2) It provides examples of how industry can achieve efficiency savings of 50-70% through measures like downsizing components, direct drive systems, and load control.
3) A case study shows how converting an oversized 10kW system to a smaller, variable speed, direct drive setup with efficient components achieves 82% energy savings and a payback period of just one year.
UN WOD 2024 will take us on a journey of discovery through the ocean's vastness, tapping into the wisdom and expertise of global policy-makers, scientists, managers, thought leaders, and artists to awaken new depths of understanding, compassion, collaboration and commitment for the ocean and all it sustains. The program will expand our perspectives and appreciation for our blue planet, build new foundations for our relationship to the ocean, and ignite a wave of action toward necessary change.
Donate to charity during this holiday seasonSERUDS INDIA
For people who have money and are philanthropic, there are infinite opportunities to gift a needy person or child a Merry Christmas. Even if you are living on a shoestring budget, you will be surprised at how much you can do.
Donate Us
https://serudsindia.org/how-to-donate-to-charity-during-this-holiday-season/
#charityforchildren, #donateforchildren, #donateclothesforchildren, #donatebooksforchildren, #donatetoysforchildren, #sponsorforchildren, #sponsorclothesforchildren, #sponsorbooksforchildren, #sponsortoysforchildren, #seruds, #kurnool
This report explores the significance of border towns and spaces for strengthening responses to young people on the move. In particular it explores the linkages of young people to local service centres with the aim of further developing service, protection, and support strategies for migrant children in border areas across the region. The report is based on a small-scale fieldwork study in the border towns of Chipata and Katete in Zambia conducted in July 2023. Border towns and spaces provide a rich source of information about issues related to the informal or irregular movement of young people across borders, including smuggling and trafficking. They can help build a picture of the nature and scope of the type of movement young migrants undertake and also the forms of protection available to them. Border towns and spaces also provide a lens through which we can better understand the vulnerabilities of young people on the move and, critically, the strategies they use to navigate challenges and access support.
The findings in this report highlight some of the key factors shaping the experiences and vulnerabilities of young people on the move – particularly their proximity to border spaces and how this affects the risks that they face. The report describes strategies that young people on the move employ to remain below the radar of visibility to state and non-state actors due to fear of arrest, detention, and deportation while also trying to keep themselves safe and access support in border towns. These strategies of (in)visibility provide a way to protect themselves yet at the same time also heighten some of the risks young people face as their vulnerabilities are not always recognised by those who could offer support.
In this report we show that the realities and challenges of life and migration in this region and in Zambia need to be better understood for support to be strengthened and tuned to meet the specific needs of young people on the move. This includes understanding the role of state and non-state stakeholders, the impact of laws and policies and, critically, the experiences of the young people themselves. We provide recommendations for immediate action, recommendations for programming to support young people on the move in the two towns that would reduce risk for young people in this area, and recommendations for longer term policy advocacy.
The Antyodaya Saral Haryana Portal is a pioneering initiative by the Government of Haryana aimed at providing citizens with seamless access to a wide range of government services
AHMR is an interdisciplinary peer-reviewed online journal created to encourage and facilitate the study of all aspects (socio-economic, political, legislative and developmental) of Human Mobility in Africa. Through the publication of original research, policy discussions and evidence research papers AHMR provides a comprehensive forum devoted exclusively to the analysis of contemporaneous trends, migration patterns and some of the most important migration-related issues.
Monitoring Health for the SDGs - Global Health Statistics 2024 - WHOChristina Parmionova
The 2024 World Health Statistics edition reviews more than 50 health-related indicators from the Sustainable Development Goals and WHO’s Thirteenth General Programme of Work. It also highlights the findings from the Global health estimates 2021, notably the impact of the COVID-19 pandemic on life expectancy and healthy life expectancy.
United Nations World Oceans Day 2024; June 8th " Awaken new dephts".Christina Parmionova
The program will expand our perspectives and appreciation for our blue planet, build new foundations for our relationship to the ocean, and ignite a wave of action toward necessary change.
RFP for Reno's Community Assistance CenterThis Is Reno
Property appraisals completed in May for downtown Reno’s Community Assistance and Triage Centers (CAC) reveal that repairing the buildings to bring them back into service would cost an estimated $10.1 million—nearly four times the amount previously reported by city staff.
Jennifer Schaus and Associates hosts a complimentary webinar series on The FAR in 2024. Join the webinars on Wednesdays and Fridays at noon, eastern.
Recordings are on YouTube and the company website.
https://www.youtube.com/@jenniferschaus/videos