The Gigging Musician pedal board package consists of an aluminum pedal board measuring 323 x 611mm that can fit up to 10 pedals, a protective wooden case, a removable storage tray, and a friction mounting system. The pedal board uses an aluminum rail system to allow different mounting options to securely attach pedals. It includes 8 friction mounts and 16 double friction mounts. The case features a folding built-in amplifier stand and handles for easy transport. A removable storage tray lined with foam allows for customization and storage of additional gear.
Equipment and Software Appendix to the 3x3 Official RulesJimmy L
This document outlines the official equipment requirements for 3x3 basketball competitions at different levels. It specifies the standards for backstops, backboards, rings, nets, padding, shot clocks, balls, game clocks, and other equipment. Requirements include size, material, color specifications, durability, and placement of each piece of equipment. The document is intended to establish standards for local organizers, manufacturers, and governing basketball organizations.
Curvy welded mesh fence, also called 3D security fencing, is made of carbon steel wires and steel tubes. Hot dipped galvanized or colourful powder coating supplies a bright and anti-corrosive surface for a durable life. Different curves on the fence panel increase security grade.
It is widely used in commercial and residential applications for different grade security protection applications. Associated posts and accessories are supplied for easy and fast installation. The posts will be buried into the earth or bolted onto a concrete or hard ground.
If you are interested in our products,
Email us: samuel@enzarindustry.com
Order Online, Safety PPE & Janitorial Products Promotion: Lots of Cooling Products for the Construction, Skillstrade and Warehousing Industries. Use our Coupons for Extra Savings
This document describes MEZ-SYPHON-FLANGE duct sealing systems that comply with DIN 24194 part 1 standards. It includes details on MEZ-SYPHON-FLANGE systems with an integrated siphon that provide a higher degree of tightness. It also describes MEZ-CORNER duct corners for attachment to duct walls, with sealing either on the inside or front side, available in galvanized steel or stainless steel in various sizes and configurations.
This document describes the design and fabrication of a mobile wood chipper. Key components include an electric motor, infeed chute, chipper disc assembly with three knives, discharge chute, and frame. Wood waste is fed into the infeed chute and engages with the rotating chipper disc equipped with three knives. The chips are ejected through the discharge chute. The machine is mounted on a framed platform equipped with wheels for mobility. Fabrication details are provided for each machine component. The chipper is designed to process wood waste up to 3 inches in diameter.
IRJET- Design and Manufacturing of Helical Copper Tube Heat Exchanger Winding...IRJET Journal
This document describes the design and manufacturing of a machine to make helical copper tube heat exchangers. Helical coil heat exchangers are compact and have high heat transfer rates but copper tubes often become elliptical during winding, reducing efficiency. The project aims to keep the copper tube circular for maximum heat transfer. It details the design of the machine, which consists of a headstock, mandrel, frame and tailstock to wind copper tube onto a rotating wooden mandrel. Various trials are conducted with unfilled, water-filled and salt-filled copper tubes to acquire a circular cross-section and minimize springback, thinning and wrinkling effects during the winding process.
The document describes the design and prototyping of a heavy lift octocopter. An octocopter uses 8 propellers arranged in 4 pairs of coaxial propellers to maximize lift. The design was optimized for an ASME student design competition rewarding payloads lifted. A coaxial design doubles lift compared to single propellers. The frame and protective shroud were manually constructed and components were chosen according to the custom design, with no preassembled kits used. The goal was to design for maximum lift within size requirements to earn the most points by lifting the heaviest payload.
Global Track China Co., Ltd is a professional manufacturer of rubber tracks and rubber pads. With our headquarter set in Australia, we have more than 20 years history. We can supply most types of rubber tracks and rubber pads which can widely applicable to different machines and equipments.
On the purpose of company’s global sales network, we have made our own distribution channels far across the world, we have set up our own representative offices and warehouses in most of the global trade strategic regions and countries such as USA, UK, France, Germany, Italy, Spain, New zealand and Japan etc. With years of efforts and development, our product is now enjoys great reputation among the market by the sales and after-sales service.
http://www.mistertrackandpad.com
service1@mistertrackandpad.com
SKYPE:gbm-intl0-9
Equipment and Software Appendix to the 3x3 Official RulesJimmy L
This document outlines the official equipment requirements for 3x3 basketball competitions at different levels. It specifies the standards for backstops, backboards, rings, nets, padding, shot clocks, balls, game clocks, and other equipment. Requirements include size, material, color specifications, durability, and placement of each piece of equipment. The document is intended to establish standards for local organizers, manufacturers, and governing basketball organizations.
Curvy welded mesh fence, also called 3D security fencing, is made of carbon steel wires and steel tubes. Hot dipped galvanized or colourful powder coating supplies a bright and anti-corrosive surface for a durable life. Different curves on the fence panel increase security grade.
It is widely used in commercial and residential applications for different grade security protection applications. Associated posts and accessories are supplied for easy and fast installation. The posts will be buried into the earth or bolted onto a concrete or hard ground.
If you are interested in our products,
Email us: samuel@enzarindustry.com
Order Online, Safety PPE & Janitorial Products Promotion: Lots of Cooling Products for the Construction, Skillstrade and Warehousing Industries. Use our Coupons for Extra Savings
This document describes MEZ-SYPHON-FLANGE duct sealing systems that comply with DIN 24194 part 1 standards. It includes details on MEZ-SYPHON-FLANGE systems with an integrated siphon that provide a higher degree of tightness. It also describes MEZ-CORNER duct corners for attachment to duct walls, with sealing either on the inside or front side, available in galvanized steel or stainless steel in various sizes and configurations.
This document describes the design and fabrication of a mobile wood chipper. Key components include an electric motor, infeed chute, chipper disc assembly with three knives, discharge chute, and frame. Wood waste is fed into the infeed chute and engages with the rotating chipper disc equipped with three knives. The chips are ejected through the discharge chute. The machine is mounted on a framed platform equipped with wheels for mobility. Fabrication details are provided for each machine component. The chipper is designed to process wood waste up to 3 inches in diameter.
IRJET- Design and Manufacturing of Helical Copper Tube Heat Exchanger Winding...IRJET Journal
This document describes the design and manufacturing of a machine to make helical copper tube heat exchangers. Helical coil heat exchangers are compact and have high heat transfer rates but copper tubes often become elliptical during winding, reducing efficiency. The project aims to keep the copper tube circular for maximum heat transfer. It details the design of the machine, which consists of a headstock, mandrel, frame and tailstock to wind copper tube onto a rotating wooden mandrel. Various trials are conducted with unfilled, water-filled and salt-filled copper tubes to acquire a circular cross-section and minimize springback, thinning and wrinkling effects during the winding process.
The document describes the design and prototyping of a heavy lift octocopter. An octocopter uses 8 propellers arranged in 4 pairs of coaxial propellers to maximize lift. The design was optimized for an ASME student design competition rewarding payloads lifted. A coaxial design doubles lift compared to single propellers. The frame and protective shroud were manually constructed and components were chosen according to the custom design, with no preassembled kits used. The goal was to design for maximum lift within size requirements to earn the most points by lifting the heaviest payload.
Global Track China Co., Ltd is a professional manufacturer of rubber tracks and rubber pads. With our headquarter set in Australia, we have more than 20 years history. We can supply most types of rubber tracks and rubber pads which can widely applicable to different machines and equipments.
On the purpose of company’s global sales network, we have made our own distribution channels far across the world, we have set up our own representative offices and warehouses in most of the global trade strategic regions and countries such as USA, UK, France, Germany, Italy, Spain, New zealand and Japan etc. With years of efforts and development, our product is now enjoys great reputation among the market by the sales and after-sales service.
http://www.mistertrackandpad.com
service1@mistertrackandpad.com
SKYPE:gbm-intl0-9
Allows easy mid-span access to optical fibers in loose buffer tubes and can access tube sizes from 1.9 mm to 3.0 mm.
Specifications
Shaves precise opening to prevent fiber damage.
Sizing channels to easily determine tube size.
Locking mechanism ensures tool will remain closed through entire shaving operation. Replacement Blade: Part No.: 80935 (5 Blades – 2 screws)
Dimensions: 3.9 x 1.5 x 0.7 in. (99 x 38 x 18 mm)
Weight: 1.36 oz (38.5g)
TeraSpin manufactures precision components for spinning machines at its facility in India. This includes drafting systems, spindles, and customized upgrades for roving and ring frames. TeraSpin was formed through A.T.E.'s acquisition of SKF India's textile machinery components business, building on SKF's expertise. Through R&D, TeraSpin's products are improved to ensure high performance and durability. Strict quality initiatives and automation help achieve consistent quality for components used worldwide in spinning mills.
Orthodontic brackets are components bonded to teeth that transfer force from archwires to move teeth into proper alignment and function. There are various bracket designs that differ in material, size, shape, and prescription. Andrews developed pre-adjusted edgewise brackets incorporating average tooth angulation, inclination, and rotation values to reduce need for archwire bending. Modern bracket types include self-ligating, ceramic, and lingual systems that offer improved aesthetics, reduced friction, and patient comfort. Proper bracket selection and placement are important for achieving an optimal orthodontic outcome.
Orthodontic brackets are components bonded to teeth that transfer force from archwires to move teeth into proper alignment and function. There are various bracket designs that differ in material, size, shape, and prescription. The development of pre-adjusted edgewise brackets aimed to directly guide teeth into normal occlusion with fewer bends in the archwire. However, individual variations still require some adjustments to achieve ideal positioning. Modern bracket types include self-ligating, ceramic, and lingual systems that offer enhanced aesthetics, mechanics, or patient comfort.
This document provides instructions for building a hexagonal home composter with a 30 liter capacity. It consists of a hexagonal frame, punched mesh, central rod, baffles, lid, and stand. Materials and tools required are listed, along with detailed assembly steps and diagrams. The composter is designed to be manually operated and has openings for proper aeration. Ready-made kits are available from Vigyan Ashram in India.
This document provides information on various tennis court equipment and accessories from Wilkins Solutions, including:
- Regulations for standard tennis court dimensions and required clearances around the court.
- Details on portable and permanent tennis posts, benches, bleachers, ball machines, shelters, towers, umpire chairs, divider nets, and more.
- Specifications for each product including materials, sizes, optional features, and warranties.
This document provides product information for column covers offered by Metal Design Systems. The column covers are available with a hairline or half-inch wide joint that can be dry, caulked, or have a silicone gasket. They are made from MCM or aluminum plate in various colors and finishes. The newly designed attachment system allows for easy installation and a tight fit of the column panels, which can also be easily removed due to an interlocking hanging system. Technical specifications are provided for the attachment system, joint types, profiles, materials, thicknesses, sizes, and tolerances.
1) A band saw machine uses a continuous metal band blade to cut metal workpieces. The blade is supported and driven by a drive wheel and idler wheel.
2) There are two main types - vertical band saws, which are more common, and horizontal band saws, which are used for simple cuts of solid materials held in a vice.
3) Key operations include ripping (cutting lengthwise), cross-cutting (cutting across the grain), mitering (cutting at an angle), re-sawing (cutting thickness), and freehand cutting (without guides for curves and angles). Band saws can cut a variety of materials and shapes.
The document discusses various specialized tools from Mate Precision Tooling for punching and forming sheet metal parts. It describes tools that eliminate burrs during punching, create bend lines for easy bending, provide fastening methods to replace welding, and reduce sheet marking on delicate materials. It also provides information on tools for precision hole punching, sequential numbering, and tool maintenance.
This document provides instructions for building a simple and inexpensive scooter. Some key points:
- The scooter can be built for around $75 and uses readily available parts like a small 2-cycle engine, chain drive, pneumatic tires, and basic frame constructed from welded steel angles.
- Assembly involves welding together the frame, installing wheels and bearings, adding an engine and belt drive system, and fabricating basic controls like brakes and handlebars.
- The finished scooter can reach speeds of 20 mph and is described as easy to operate, requiring only a twist of the throttle to go with no clutch or gear shifting. It provides an affordable alternative to transport for short trips around town.
This document provides a catalog and description for a ring spinning frame for cotton produced by H&B American Machine Company. Key details include:
- It describes the various parts of the ring spinning frame and emphasizes the importance of maintenance and quality components for optimal yarn production.
- The latest model, the Model "B", incorporates improvements over previous models for increased efficiency and lighter operation while maintaining ruggedness.
The document provides instructions for building a recycled bike trailer using old bicycle parts and minimal additional materials. The trailer is designed to carry heavy loads and be pulled by a bicycle to transport goods, tools, water, and more. Key steps include measuring and cutting frame parts to size, drilling holes for the wheels, attaching the wheels, and creating a flexible joint between the trailer and bicycle using a pipe bender inserted into handlebar sections. The goal is to produce a low-cost, simple trailer that can be assembled by anyone with basic technical skills.
This document provides information on the Legacy implant system, including implant designs, dimensions, surfaces, and packaging. It contains the following key details:
- The Legacy system includes tapered implants with mini-threads and double-lead threads to reduce stress and facilitate faster insertion. Implants are offered in SBM and HA surface options.
- Implant dimensions, designs, and specifications are shown for Legacy1, 2, 3, and 4 implants across different diameters, lengths, threads, tapers, and platforms.
- Packaging and components are described, including carriers, extenders, and cover screws. Pricing and part numbers are listed for SBM and HA surfaced implants in various sizes.
This document provides installation instructions for a keyboard track spacer kit. It includes diagrams and lists of included parts like spacers, screws, and brackets. The instructions are:
1) Measure the height needed to clear any obstructions and choose the right spacer/screw combination.
2) Assemble the spacers and brackets to the keyboard track using the screws and nuts provided.
3) Attach the track/spacer assembly to the underside of the work surface using wood screws through the mounting brackets.
You can start building your own MOST using a set of commercially available materials. Take a look at an instructable of how to start off building the TRAY.
Orion Ornamentam Iron 3D Drapery Hardware Brochureartbyorion
http://www.ironartbyorion.com/ : Introducing our newest product offering, 3D Drapery Hardware! Explore new window designs with the ability to have the finial in front of the rod.
The document discusses various tooling products from Mate Precision Tooling including rollerball assemblies, sheetmarkers, ultra light springs, fully guided tooling, brush dies, adapters, and slug free dies. It provides examples of how these products can solve problems when punching, forming, and marking various materials. Specifications are given for tools used on different machine stations and materials.
This document describes the fabrication and machining process for manufacturing a turnbuckle. It involves turning, drilling, boring, and threading steel rods to create the main body and threaded ends of the turnbuckle. Specific steps include reducing the diameter of rods, cutting threads on each end, drilling holes, and assembling the turnbuckle components. Precautions for use and estimated manufacturing costs are also provided.
The document describes the development of a frugal manufacturing process for white canes used by visually impaired people. Three processes were evaluated: die-necking, split die crimping, and tube spinning. Tube spinning, using a customized roller tool with a radius of 6.5mm and mandrel for support, produced results similar to commercially available canes. Further refinements based on user feedback led to prototype canes with advantages over commercial versions. The aim is to standardize the tube spinning process plan detailing materials, tools, operations, and quality measures.
PDF SubmissionDigital Marketing Institute in NoidaPoojaSaini954651
https://www.safalta.com/online-digital-marketing/advance-digital-marketing-training-in-noidaTop Digital Marketing Institute in Noida: Boost Your Career Fast
[3:29 am, 30/05/2024] +91 83818 43552: Safalta Digital Marketing Institute in Noida also provides advanced classes for individuals seeking to develop their expertise and skills in this field. These classes, led by industry experts with vast experience, focus on specific aspects of digital marketing such as advanced SEO strategies, sophisticated content creation techniques, and data-driven analytics.
Allows easy mid-span access to optical fibers in loose buffer tubes and can access tube sizes from 1.9 mm to 3.0 mm.
Specifications
Shaves precise opening to prevent fiber damage.
Sizing channels to easily determine tube size.
Locking mechanism ensures tool will remain closed through entire shaving operation. Replacement Blade: Part No.: 80935 (5 Blades – 2 screws)
Dimensions: 3.9 x 1.5 x 0.7 in. (99 x 38 x 18 mm)
Weight: 1.36 oz (38.5g)
TeraSpin manufactures precision components for spinning machines at its facility in India. This includes drafting systems, spindles, and customized upgrades for roving and ring frames. TeraSpin was formed through A.T.E.'s acquisition of SKF India's textile machinery components business, building on SKF's expertise. Through R&D, TeraSpin's products are improved to ensure high performance and durability. Strict quality initiatives and automation help achieve consistent quality for components used worldwide in spinning mills.
Orthodontic brackets are components bonded to teeth that transfer force from archwires to move teeth into proper alignment and function. There are various bracket designs that differ in material, size, shape, and prescription. Andrews developed pre-adjusted edgewise brackets incorporating average tooth angulation, inclination, and rotation values to reduce need for archwire bending. Modern bracket types include self-ligating, ceramic, and lingual systems that offer improved aesthetics, reduced friction, and patient comfort. Proper bracket selection and placement are important for achieving an optimal orthodontic outcome.
Orthodontic brackets are components bonded to teeth that transfer force from archwires to move teeth into proper alignment and function. There are various bracket designs that differ in material, size, shape, and prescription. The development of pre-adjusted edgewise brackets aimed to directly guide teeth into normal occlusion with fewer bends in the archwire. However, individual variations still require some adjustments to achieve ideal positioning. Modern bracket types include self-ligating, ceramic, and lingual systems that offer enhanced aesthetics, mechanics, or patient comfort.
This document provides instructions for building a hexagonal home composter with a 30 liter capacity. It consists of a hexagonal frame, punched mesh, central rod, baffles, lid, and stand. Materials and tools required are listed, along with detailed assembly steps and diagrams. The composter is designed to be manually operated and has openings for proper aeration. Ready-made kits are available from Vigyan Ashram in India.
This document provides information on various tennis court equipment and accessories from Wilkins Solutions, including:
- Regulations for standard tennis court dimensions and required clearances around the court.
- Details on portable and permanent tennis posts, benches, bleachers, ball machines, shelters, towers, umpire chairs, divider nets, and more.
- Specifications for each product including materials, sizes, optional features, and warranties.
This document provides product information for column covers offered by Metal Design Systems. The column covers are available with a hairline or half-inch wide joint that can be dry, caulked, or have a silicone gasket. They are made from MCM or aluminum plate in various colors and finishes. The newly designed attachment system allows for easy installation and a tight fit of the column panels, which can also be easily removed due to an interlocking hanging system. Technical specifications are provided for the attachment system, joint types, profiles, materials, thicknesses, sizes, and tolerances.
1) A band saw machine uses a continuous metal band blade to cut metal workpieces. The blade is supported and driven by a drive wheel and idler wheel.
2) There are two main types - vertical band saws, which are more common, and horizontal band saws, which are used for simple cuts of solid materials held in a vice.
3) Key operations include ripping (cutting lengthwise), cross-cutting (cutting across the grain), mitering (cutting at an angle), re-sawing (cutting thickness), and freehand cutting (without guides for curves and angles). Band saws can cut a variety of materials and shapes.
The document discusses various specialized tools from Mate Precision Tooling for punching and forming sheet metal parts. It describes tools that eliminate burrs during punching, create bend lines for easy bending, provide fastening methods to replace welding, and reduce sheet marking on delicate materials. It also provides information on tools for precision hole punching, sequential numbering, and tool maintenance.
This document provides instructions for building a simple and inexpensive scooter. Some key points:
- The scooter can be built for around $75 and uses readily available parts like a small 2-cycle engine, chain drive, pneumatic tires, and basic frame constructed from welded steel angles.
- Assembly involves welding together the frame, installing wheels and bearings, adding an engine and belt drive system, and fabricating basic controls like brakes and handlebars.
- The finished scooter can reach speeds of 20 mph and is described as easy to operate, requiring only a twist of the throttle to go with no clutch or gear shifting. It provides an affordable alternative to transport for short trips around town.
This document provides a catalog and description for a ring spinning frame for cotton produced by H&B American Machine Company. Key details include:
- It describes the various parts of the ring spinning frame and emphasizes the importance of maintenance and quality components for optimal yarn production.
- The latest model, the Model "B", incorporates improvements over previous models for increased efficiency and lighter operation while maintaining ruggedness.
The document provides instructions for building a recycled bike trailer using old bicycle parts and minimal additional materials. The trailer is designed to carry heavy loads and be pulled by a bicycle to transport goods, tools, water, and more. Key steps include measuring and cutting frame parts to size, drilling holes for the wheels, attaching the wheels, and creating a flexible joint between the trailer and bicycle using a pipe bender inserted into handlebar sections. The goal is to produce a low-cost, simple trailer that can be assembled by anyone with basic technical skills.
This document provides information on the Legacy implant system, including implant designs, dimensions, surfaces, and packaging. It contains the following key details:
- The Legacy system includes tapered implants with mini-threads and double-lead threads to reduce stress and facilitate faster insertion. Implants are offered in SBM and HA surface options.
- Implant dimensions, designs, and specifications are shown for Legacy1, 2, 3, and 4 implants across different diameters, lengths, threads, tapers, and platforms.
- Packaging and components are described, including carriers, extenders, and cover screws. Pricing and part numbers are listed for SBM and HA surfaced implants in various sizes.
This document provides installation instructions for a keyboard track spacer kit. It includes diagrams and lists of included parts like spacers, screws, and brackets. The instructions are:
1) Measure the height needed to clear any obstructions and choose the right spacer/screw combination.
2) Assemble the spacers and brackets to the keyboard track using the screws and nuts provided.
3) Attach the track/spacer assembly to the underside of the work surface using wood screws through the mounting brackets.
You can start building your own MOST using a set of commercially available materials. Take a look at an instructable of how to start off building the TRAY.
Orion Ornamentam Iron 3D Drapery Hardware Brochureartbyorion
http://www.ironartbyorion.com/ : Introducing our newest product offering, 3D Drapery Hardware! Explore new window designs with the ability to have the finial in front of the rod.
The document discusses various tooling products from Mate Precision Tooling including rollerball assemblies, sheetmarkers, ultra light springs, fully guided tooling, brush dies, adapters, and slug free dies. It provides examples of how these products can solve problems when punching, forming, and marking various materials. Specifications are given for tools used on different machine stations and materials.
This document describes the fabrication and machining process for manufacturing a turnbuckle. It involves turning, drilling, boring, and threading steel rods to create the main body and threaded ends of the turnbuckle. Specific steps include reducing the diameter of rods, cutting threads on each end, drilling holes, and assembling the turnbuckle components. Precautions for use and estimated manufacturing costs are also provided.
The document describes the development of a frugal manufacturing process for white canes used by visually impaired people. Three processes were evaluated: die-necking, split die crimping, and tube spinning. Tube spinning, using a customized roller tool with a radius of 6.5mm and mandrel for support, produced results similar to commercially available canes. Further refinements based on user feedback led to prototype canes with advantages over commercial versions. The aim is to standardize the tube spinning process plan detailing materials, tools, operations, and quality measures.
PDF SubmissionDigital Marketing Institute in NoidaPoojaSaini954651
https://www.safalta.com/online-digital-marketing/advance-digital-marketing-training-in-noidaTop Digital Marketing Institute in Noida: Boost Your Career Fast
[3:29 am, 30/05/2024] +91 83818 43552: Safalta Digital Marketing Institute in Noida also provides advanced classes for individuals seeking to develop their expertise and skills in this field. These classes, led by industry experts with vast experience, focus on specific aspects of digital marketing such as advanced SEO strategies, sophisticated content creation techniques, and data-driven analytics.
Explore the essential graphic design tools and software that can elevate your creative projects. Discover industry favorites and innovative solutions for stunning design results.
Architectural and constructions management experience since 2003 including 18 years located in UAE.
Coordinate and oversee all technical activities relating to architectural and construction projects,
including directing the design team, reviewing drafts and computer models, and approving design
changes.
Organize and typically develop, and review building plans, ensuring that a project meets all safety and
environmental standards.
Prepare feasibility studies, construction contracts, and tender documents with specifications and
tender analyses.
Consulting with clients, work on formulating equipment and labor cost estimates, ensuring a project
meets environmental, safety, structural, zoning, and aesthetic standards.
Monitoring the progress of a project to assess whether or not it is in compliance with building plans
and project deadlines.
Attention to detail, exceptional time management, and strong problem-solving and communication
skills are required for this role.
Revolutionizing the Digital Landscape: Web Development Companies in Indiaamrsoftec1
Discover unparalleled creativity and technical prowess with India's leading web development companies. From custom solutions to e-commerce platforms, harness the expertise of skilled developers at competitive prices. Transform your digital presence, enhance the user experience, and propel your business to new heights with innovative solutions tailored to your needs, all from the heart of India's tech industry.
EASY TUTORIAL OF HOW TO USE CAPCUT BY: FEBLESS HERNANEFebless Hernane
CapCut is an easy-to-use video editing app perfect for beginners. To start, download and open CapCut on your phone. Tap "New Project" and select the videos or photos you want to edit. You can trim clips by dragging the edges, add text by tapping "Text," and include music by selecting "Audio." Enhance your video with filters and effects from the "Effects" menu. When you're happy with your video, tap the export button to save and share it. CapCut makes video editing simple and fun for everyone!
Maximize Your Content with Beautiful Assets : Content & Asset for Landing Page pmgdscunsri
Figma is a cloud-based design tool widely used by designers for prototyping, UI/UX design, and real-time collaboration. With features such as precision pen tools, grid system, and reusable components, Figma makes it easy for teams to work together on design projects. Its flexibility and accessibility make Figma a top choice in the digital age.
Fonts play a crucial role in both User Interface (UI) and User Experience (UX) design. They affect readability, accessibility, aesthetics, and overall user perception.
Visual Style and Aesthetics: Basics of Visual Design
Visual Design for Enterprise Applications
Range of Visual Styles.
Mobile Interfaces:
Challenges and Opportunities of Mobile Design
Approach to Mobile Design
Patterns
Technoblade The Legacy of a Minecraft Legend.Techno Merch
Technoblade, born Alex on June 1, 1999, was a legendary Minecraft YouTuber known for his sharp wit and exceptional PvP skills. Starting his channel in 2013, he gained nearly 11 million subscribers. His private battle with metastatic sarcoma ended in June 2022, but his enduring legacy continues to inspire millions.
1. Pedal Mount
Pedal Mount 2
Friction Mount
Double Friction Mount
5/8” Microphone
Mount
3/8” Microphone
Mount
Mounts
Gigging Musician
The Gigging Musician pedal board consists of; an aluminum 323 x
611mm pedal board that can easily fit 10 pedals, a protective wooden
case, a removable storage tray, and the friction mounting system.
The pedal board is constructed of 30 x 23mm and 23 x 23mm aluminum
extrusions, that allow for a simple mounting solution of pedals to the
board by selecting the preferred mounting system and sliding it into the
rails. The Gigging Musician package has a friction mounting system
included. The rail system is secured to an aluminum
base. This base has a handle on either side which
allows for the user to easily remove the board from the
case with ease. The base also has a magnetic bottom
plate, when removed gives the user access to the
underside of the rails, to easily manage the cables
through the rails. This bottom plate can also have a
power supply mounted to it, with a slot in the back of the
base and case for power cables to be passed through,
allowing for the board to be used whilst in the case (a
wooden plate with magnets attaches to the case to close
this slot during transport).
The friction mounting system comes with 8 Friction
Mounts and 16 Double Friction Mounts. These should
allow the user to store 10 pedals comfortably on the
board. The friction system works by having friction
mounts on either side of the pedal (2 recommended on
either side), tightening 2 of the friction mounts on one
side of the pedal using the wing nut, then pressing 2
double friction mounts on the opposite side of the pedal
into the pedal and the tightened mounts, and then
securing the remaining mounts to the board with the
wing nut. This creates a clamping pressure on the
pedals, securing them to the board.
The lid is secured to the case with 2 toggle latches front
and back. The lid has a built in Universal Amplifier stand
which folds out.
The storage tray is secured to the case with toggle
latches on either side, allowing for it to be detached. It
has a foam block, which the user can cut out custom
slots to store any necessary items, such as, extra
cables, finger slide, capo, plectrums, spare guitar strings
etc.
Price - £200
2. Component Materials Used
Board Rails • Black Anodised Aluminum (glossy)
Board Rail Bracket • 3mm Black Anodised Aluminum (glossy)
Board Base
• 3mm Dark Grey Anodised Aluminum (rough)
• Square Neodymium Magnets
Savio Board Base
Branding (Handles and
Back)
• PVC Vinyl
Case
• 7mm Dark Bamboo Plywood (semi-gloss)
*Walnut was used for wood components as the
rendering texture, as there were texture issues
with the software*
• Nickle Plated Steel Toggle Latches
• Polyethylene Foam
• Nickle Plated Steel Handle, Black Leather on
Handle Grip
• Round Neodymium Magnets
Case Cable Door
• 7mm Dark Bamboo (semi-gloss)
• Round Neodymium Magnets
Case Lid
• 7mm Dark Bamboo (semi-gloss)
• Nickle Plated Steel Toggle Latches
• 4mm Dark Grey Anodised Aluminum (rough)
• 3mm Steel Rod
• Flat Woven Elastic
• ABS Side Release Buckle
Savio Case Branding
(Front)
• Polished Chrome
Savio Case Logo (Top) • PVC Vinyl
Storage Tray
• 7mm Dark Bamboo (semi-gloss)
• Nickle Plated Steel Toggle Latches
• Polyethylene Foam
Mounting Systems
The friction mount system employs a clamping pressure to mount the a
pedal to the board. Ideally 4 mounts are used per pedal. The pedals
closest to either side of the board will have 2 friction mounts on the
outside face and 2 double friction mounts on the inside. Using this layout
allows the user to get the maximum usage out of the board. The double
friction mounts are 44mm long, which should be suitable distance
between each pedal to allows for cables. The user can opt for using only
friction mounts, enabling them to space out the pedals further.
The pedal mount system is similar to the bike chain link method of
mounting pedals to a board. One end of the mount is mounted to the
rails of the board, and the other uses a thumb screw that threads into the base of the pedal. On the pedal mount 2, the slot for the pedal is
recessed, to allow the use of the screw/bolt that is already in the pedal, as this slot is only 1mm thick in this area. The pedal mounts are
attached to the four corners of the pedal.
The mounts that I have designed, were designed with the intentions of being as robust as possible, simple, and inexpensive to produce.
For all of the mounts, the main body is made from 3mm thick Stainless steel. This would be laser cut and bent into shape. The laser cutting
would cut out the general shape of the body and the bolt holes. The
additional features would then be bent into shape, depending on the
specific mount. The mounts (not applicable to double friction mount)
have a small 5mm 45° bend on the back of the mount. This bend is
intended to provide the user with better ergonomics to slide the mount
along the rail, and make it easier to apply clamping pressure. The main
bodies requires minimal post processing, with each part given a gloss
black anodised coating to provide additional protection against corrosion/
rust. This coating will also help disguise the mounts with the black
anodised rails on the board, for better aesthetics. A small chamfer would
be added to all the edges to take away any sharp edges from the laser
cutting. The two friction mounts also have an adhesive rubber plate
applied to the clamping faces, firstly for additional friction between the
mount and the pedals, and to protect the pedals from being marked, as
the mounts are made from stainless steel.
Each mount is secured to the board with a square ABS block which
slides along the inner of the rails. This ABS block would be injection
moulded for rapid production and low per part costs. An M6 bolt is
passed through the ABS block (extrusion cut in the part allows for the
head of the bolt to sit flush inside the block) and through the hole in the body of the mount. This is then tightened down to the board with a
wing nut on top of the mount body. Both the M6 bolts and the wing nuts would be bought in bulk as these are readily available fasteners. I
decided to use a bolt and wing nut to ensure a simple design, which has less chance of failure as there is a reduction in moving parts, and
if the user loses a bolt or wing nut, they are readily available at any hardware store.
The pedal mount design has a thumb screw in the design, this again
would be bought in bulk depending on the thread diameter requirements
of different pedal manufacturers. The thumb screws allows the user to
easily hand tighten the mount to the underside of a pedal, in the same
manner of a bike chain link system. The thumb screw would have a slot
cut into the head of the screw, for extra tightening using the likes of a
coin if required. An area around the slot on the pedal mount 2 is
recessed by 2mm, to allow the use of the screws already used on the
underside of a pedal, providing a truly universal solution.
During research of mic stands, the two most common threads used are
5/8” - 27 and 3/8” - 16. I have designed a mount for each of these thread
types. The main body is the same as the other mounts, but I have
included 2 bolt holes on the mic mounts, to ensure the microphone is
stable when mounted. Stainless steel rods would be cut to length, a hole
would be milled into one side, this would then be tapped to the specific
thread diameter and length. The barrel would then be welded to the
mount body before the normal post processing stages.
3/8 Mic Mount 5/8 Mic Mount
Friction Mount Double Friction Mount
Pedal Mount Pedal Mount 2
3. Pedal Board
Rail Design
Extrusion Profiles
Rail Bracket
From left to right - the first profile is 23 x 22.75mm, the next seven
profiles are the same at 30 x 23mm, and the last profile is again 23 x
22.75mm. Each one is 600mm in length. In the centre of each
extrusion are two 2.5mm diameter screw ports, that allows a 3mm self
tapping screw to fasten the extrusions to the bracket.
The rail bracket is 29.2 (H) x 23 (W) x 314 (L)mm. It has slots to fit the
profile of the mounts, allowing them to slide along the rails. Holes are
aligned 33.5mm apart to ensure that the extrusions are the perfect
distance apart, ensuring the correct tolerance to allow the mounts to
slide with ease. Each hole is 3mm for the self tapping screws to secure
the extrusions to the bracket. There are four 3mm holes along the
centre of the bracket. These holes are there to fasten the assembly to
the aluminum pedal board shell.
Pedal Board Packages
1. The Hobbyist (up to 10 Pedals) - £100 - Includes; a 323 x 614mm Pedal Board.
2. The Gigging Musician (up to 10 Pedals) - £200 - Includes; a 323 x 614mm Pedal
Board, Friction Mounting system (8 Friction Mounts & 16 Double Friction Mounts), Wooden
case with built in Folding Amplifier Stand, and a removable Storage Tray.
3. The Professional (up to 16 Pedals) - £300 - Includes; a 323 x 814mm Pedal Board,
choice of mounting system, choice of Microphone Stand, Wooden case with built in Folding
Amplifier Stand, and a removable Storage Tray.
The board is constructed from black anodised aluminum extrusions (detailed right),
secured to black anodised aluminum brackets, that are then fastened to a dark grey rough
anodised aluminum shell, with 3mm bolts. This forms the rails that allow for to mounting
systems to slide along the board. The extrusions are glossy to allow the mounts to glide
along the rails.
As a rail system was used, mentioned in the research report, this allows the user to apply
Hook & Loop / Velcro tape to the board. Therefore, if the user selects The Hobbyist
package, they can choose to use 30mm Hook & Loop / Velcro tape, or they can add one of
our mounting systems of choice at an additional cost.
The rail system also allows the users to pass cables through the slots to the underside of
the board. The pedal board shell has a magnetic bottom plate, with strong neodymium
magnets to secure it to the shell. This can be easily removed, giving the user access to the
underside of the board to manage their cables, out of sight from the top of the board. A
power supply can also be mounted to this bottom plate to store inside the board. There is a
cutout on the back of the shell that allows for the power cable to be passed through. The
bottom plate has non-slip rubber feet on the underside, to prevent the board marking any
flooring, and to prevent the board from sliding during use.
The pedal board has a 10° tilt towards the user on the top face. This makes it more
ergonomic for the user to activate the pedals towards the back of the board. The shell also
has a handle on either side, making it easier for the board to be lifted and moved, or
removed from the case. Chrome effect decals of the Savio brand name are on the outside
of these handle, as well as on the back of the board, for audience members to see.
With further planning, the board design could be optimised for laser cutting and bending
using 3mm sheet aluminum, that would be assembled with fasteners. Another option would
be aluminum die casting. Post production would include a dark grey anodisation to protect
the metal from corrosion, and the removal of any sharp edges with a small fillet.
4. Pedal Board Case
Branding
Savio Brand Name
Savio Logo
Universal Folding Amplifier Stand
The folding arms have are designed to
be at a 30° tilt upwards, which was
requested in the design proposal. The
wings are 345mm apart which should fit
the most popular amps (based off the
ones I had researched), with the back of
the wings being 250mm long for the amp
to rest on.
A folding Amplifier stand is mounted on the inside of the case lid.
It’s constructed from 4mm sheet aluminum and has a dark grey
anodised coating to match the pedal board. The wings of the
stand hinge open on stainless steel rods. The stand is secured
closed by woven elasticated bands and a side release buckle.
The wooden pedal board case is included with the Gigging Musician and Professional pedal
board packages. It is a stylish box made from dark semi-gloss bamboo plywood (in the
renders walnut has been used as there was an issue processing the bamboo plywood
texture). In the model I used 7mm thick plywood, but I think it would be more suitable to use
12mm or thicker to ensure that the box is sturdy enough for the environments it would be put
in. The wooden boards would be joined together with glued mitre joints. This would have to
be tested to ensure that it is durable, but I think that metal corner plates could be added to the
outside of the joints to reinforce them.
A nickle plated steel handle with a leather grip on the front of the case transporting the board
from place to place, in a briefcase style. When in transport, the case shows off a coloured
decal of the Savio logo. On the front of the case above the handle, is the Savio brand name
in polished chrome.
Inside the case is 15mm thick Polyethylene Foam that is moulded to fit the pedal board snug
inside the case. This is in place to help protect the board inside the case from any knocks and
bumps. On the back of the case, there is a magnetic cable door. This is simply a cutout in the
back of the case, which allows power cables to pass through the case, allowing the board to
be used without having to remove it from the case. The case also has a 10° slant in the
design, to match the tilt of the board, ensuring that the board is fully functional whilst the lid is
removed from the main body.
The cable door can be quickly closed again with round neodymium magnets on a matching
piece of plywood, that snaps in place, preventing loose items inside the board from falling out
of the case. This require there to be neodymium magnets embedded into both the plywood
cable door and the case, which can simply done with a drilled hole and glue. The handle on
the pedal board protrude from the case when it is open, making it more ergonomic for the
user to get a grip of the board to remove it.
Nickle Plated Steel Toggle Latches makes it quick to remove the lid and storage tray from the
case. The orientation of the toggle latches on the storage tray was purposely chosen to have
the latches on the storage tray and the catches on the case. This was done so that if the
storage tray was not required it could be removed, and the user wouldn’t be carrying the case
with latches flopping around, or having to carry unnecessary weight. The toggle latches
would be bought in bulk as these are a readily available item. Another option to use are
butterfly latches, which are commonly found on flight cases as an alternative to toggle
latches. Butterfly latches are more robust, but are more costly in comparison to toggle
latches.
The storage tray consists of a block of 629 x 338 x 40mm
Polyethylene Foam, that provides a customisable storage solution to
the user. They can cut the foam to suit their storage requirements,
with plenty of room for a finger slide, extra strings, plectrums and much
more. The foam will provide some impact protection to the items
during any knocks etc, and will hold the items securely in place.