Optical Communication Part 10 Enabling Devices: Passive Components

1. Taiz University, YEMEN
4 October 2018

2. Taiz University, YEMEN
• A permanent joint formed between two
individual optical fibers in the field or factory
is known as a fiber splice.
• Fiber splicing is frequently used to establish
long-haul optical fiber links where smaller
fiber lengths need to be joined.
• There is no requirement for repeated
connection and disconnection.
4 October 2018 2

3. Taiz University, YEMEN
• Demountable fiber connectors are more difficult to achieve
than optical fiber splices. This is because they must maintain
similar tolerance requirements to splices in order to couple
light between fibers efficiently, but they must accomplish it in
a removable fashion.
• Also, the connector design must allow for repeated
connection and disconnection without problems of fiber
alignment, which may lead to degradation in the performance
of the transmission line at the joint.
• Hence to operate satisfactorily the demountable connector
must provide reproducible accurate alignment of the optical
fibers.
4 October 2018 3

4. Taiz University, YEMEN
Fused biconical taper (FBT) coupler
Micro-optics coupler
Waveguide coupler
4 October 2018 4

5. Taiz University, YEMEN
• Fixed for one wavelength also known as
achromatic coupler
• Coupler designed to work for two or more
wavelengths simultaneously also known as
WDM coupler
4 October 2018 5

6. Taiz University, YEMEN
4 October 2018 6

7. Taiz University, YEMEN
4 October 2018 7

8. Taiz University, YEMEN
• Excess loss
• Insertion loss:
Port 1 to 3
Port 1 to 4
• Crosstalk
• Split ratio
4
3
1
log
10
P
P
P

3
1
log
10
P
P
4
1
log
10
P
P
1
2
log
10
P
P






 4
3
3
P
P
P
1
2
3
4

9. Taiz University, YEMEN
1. Polymer on silica
2. Polymer on silicon
3. Silica on silica
4. Silica on silicon

10. Taiz University, YEMEN

11. Taiz University, YEMEN

12. Taiz University, YEMEN
A four-port multimode fiber FBT coupler has 60
μW optical power launched into port 1. The
measured output powers at ports 2, 3 and 4 are
0.004, 26.0 and 27.5 μW respectively.
Determine the excess loss, the insertion losses
between the input and output ports, the
crosstalk and the split ratio for the device.
Answers: 0.5 dB, 3.63 dB, 3.39 dB, −41.8 dB, 48.6%.
4 October 2018 12
Example

13. Taiz University, YEMEN
• The splitting loss is related to the number of
output ports N following:
• For a single input port and multiple output
ports where j = 1, N, then the excess loss is
given by:
4 October 2018 13

14. Taiz University, YEMEN
• MUX – combines several wavelength into
one fiber.
• DEMUX – separates several wavelength.
Coupler- combines signal at the same
wavelength and a WDM MUX couples
different wavelength.

15. Taiz University, YEMEN

16. Taiz University, YEMEN

17. Taiz University, YEMEN

18. Taiz University, YEMEN

19. Taiz University, YEMEN

20. Taiz University, YEMEN

21. Taiz University, YEMEN

22. Taiz University, YEMEN

23. Taiz University, YEMEN

24. Taiz University, YEMEN

25. Taiz University, YEMEN

26. Taiz University, YEMEN

27. Taiz University, YEMEN
Channel spacing:
DWDM 0.4 nm (50 GHz)
WDM 0.8 nm (100 GHz) and 1.6 nm (200 GHz)
CWDM 20 nm
  .
50
1550
10
3
4
.
0
2
8
2
GHz
f
c
f
f
f
















28. Taiz University, YEMEN

29. Taiz University, YEMEN 29
4 October 2018