Ma 032 transfer water from or to supply boat
•Download as DOC, PDF•
0 likes•369 views
This document summarizes the job safety analysis for receiving water from a supply boat. It identifies potential hazards including the hose falling in the sea, pinch points when connecting or lifting the hose, the hose becoming blocked or bursting, and ensuring the correct tank is lined up. Recommendations are made such as inspecting the hose before connecting, having at least two people control the lifting hook, monitoring the hose frequently, and wearing a work vest and not standing on handrails when reconnecting to the rig. Required safety equipment includes hard hats, safety boots, gloves, goggles, and work vests.
Report
Share
Report
Share
Recommended
Ma 031 transfer brine from or to supply boat
This document outlines the steps and safety procedures for receiving brine from a supply boat. It details potential hazards such as hoses falling in the sea, pinch points, and personnel being struck or caught. Recommendations are provided to minimize hazards, such as inspecting hoses, having a minimum of two people connect and control the lifting hook, barricading areas, and wearing proper safety equipment like work vests, hard hats, and safety boots. Personnel are to monitor tank levels during the transfer and stop if abnormalities are observed.
Aw syringe n
The document provides instructions for installing an air/water syringe. It outlines 4 steps: 1) relieve pressure in the existing syringe; 2) disconnect the existing syringe by unscrewing the handle and cutting the tubing; 3) insert the tubing through the new handle and slip sleeve clamps over each line before placing the tubing over the barbs; 4) turn the unit on to test for leaks and ensure proper function. Care should be taken not to break the barbs when installing and softening the tubing ends in hot water can make sliding them over the barbs easier.
Ma 001 tanks & preloads visual inspection
This Job Safety Analysis outlines the steps and potential hazards for inspecting tanks and preloads. The 6 steps are: 1) holding a pre-job meeting, 2) preparing inspection tools, 3) inspecting atmospheric conditions, 4) entering the tank, 5) conducting the tank inspection, and 6) exiting the tank. Hazards include falling, electric shock, tripping, poor visibility, and dangerous atmospheric conditions. Recommendations are made such as checking equipment, using fall protection, ventilation, and having a stand-by person outside the tank.
Ma 023 change out butter fly valve for bulk system
This Job Safety Analysis outlines the steps and potential hazards involved in changing a valve in a bulk tank. The key steps are: reviewing safety procedures, gathering equipment, isolating and locking out the air supply, removing and replacing valves, repairing valves, and reopening the air supply. Potential hazards include trip/slip hazards, pinch points, exposure to high pressure, and caught between hazards. Recommendations are provided to eliminate hazards through proper planning, inspecting equipment and work areas, using fall protection when working above deck, and maintaining safe distances when pressurizing tanks.
Ma 037 cleaning with air brush
The document outlines the steps and potential hazards involved in cleaning with an air brush. It describes connecting the air brush to an air provider and isolating tools before breaks to prevent uncontrolled movements. Recommendations are made to use plastic joints, safety clips, and cables to secure hoses and prevent leaks, sparks, or flying debris. Personal protective equipment like hard hats, safety boots, and ear protection are required.
Ma 020 launching lifeboats to sea
This document contains a job safety analysis for launching lifeboats to sea from an offshore drilling rig. It outlines the basic job steps, potential accidents and hazards at each step, and recommendations to reduce risks. The seven steps are: 1) pre-job meeting, 2) opening lifeboat doors and checks, 3) testing operations without personnel, 4) embarking crew, 5) lowering to sea and releasing, 6) testing in sea, and 7) raising back. Hazards include falling overboard, equipment failures, injuries from incorrect procedures. Recommendations focus on wearing lifejackets, checking equipment, going slowly, having competent operators, and getting weather forecasts.
Ma 115 boom crane cable tray repair
1) This Job Safety Analysis document outlines the steps and potential hazards involved in repairing a cable tray using a crane. The work team includes a crane operator and electricians. Required safety equipment includes hard hats, safety boots, gloves, safety glasses, and harnesses.
2) The basic job steps are to hold a pre-job meeting, place the crane boom on a cradle and install planking, secure the cable tray, and remove the planking at the end of the job. Potential hazards addressed are procedures not being understood, crane failure, dropping tools, and tools falling from the boom.
3) Recommendations are provided to take time to ensure the JSA is understood,
Ma 025 transfer casing
This document outlines the steps and potential hazards involved in transferring casing from the pipe rack to the rig floor. It describes lifting the casing joint from the pipe rack to the walkway, then from the walkway to the rig floor using slings. Potential hazards include a casing fall if the sling breaks or someone is hit by a joint. Recommendations are made to check lifting equipment, use tag lines, and have personnel stand clear. When lowering the casing on the ramp, good communication is needed between tugger operators to prevent damage or a casing fall. Ramp stoppers must be correctly installed to reduce protector falls on the ramp. Safety equipment like hard hats and safety glasses are required.
Recommended
Ma 031 transfer brine from or to supply boat
This document outlines the steps and safety procedures for receiving brine from a supply boat. It details potential hazards such as hoses falling in the sea, pinch points, and personnel being struck or caught. Recommendations are provided to minimize hazards, such as inspecting hoses, having a minimum of two people connect and control the lifting hook, barricading areas, and wearing proper safety equipment like work vests, hard hats, and safety boots. Personnel are to monitor tank levels during the transfer and stop if abnormalities are observed.
Aw syringe n
The document provides instructions for installing an air/water syringe. It outlines 4 steps: 1) relieve pressure in the existing syringe; 2) disconnect the existing syringe by unscrewing the handle and cutting the tubing; 3) insert the tubing through the new handle and slip sleeve clamps over each line before placing the tubing over the barbs; 4) turn the unit on to test for leaks and ensure proper function. Care should be taken not to break the barbs when installing and softening the tubing ends in hot water can make sliding them over the barbs easier.
Ma 001 tanks & preloads visual inspection
This Job Safety Analysis outlines the steps and potential hazards for inspecting tanks and preloads. The 6 steps are: 1) holding a pre-job meeting, 2) preparing inspection tools, 3) inspecting atmospheric conditions, 4) entering the tank, 5) conducting the tank inspection, and 6) exiting the tank. Hazards include falling, electric shock, tripping, poor visibility, and dangerous atmospheric conditions. Recommendations are made such as checking equipment, using fall protection, ventilation, and having a stand-by person outside the tank.
Ma 023 change out butter fly valve for bulk system
This Job Safety Analysis outlines the steps and potential hazards involved in changing a valve in a bulk tank. The key steps are: reviewing safety procedures, gathering equipment, isolating and locking out the air supply, removing and replacing valves, repairing valves, and reopening the air supply. Potential hazards include trip/slip hazards, pinch points, exposure to high pressure, and caught between hazards. Recommendations are provided to eliminate hazards through proper planning, inspecting equipment and work areas, using fall protection when working above deck, and maintaining safe distances when pressurizing tanks.
Ma 037 cleaning with air brush
The document outlines the steps and potential hazards involved in cleaning with an air brush. It describes connecting the air brush to an air provider and isolating tools before breaks to prevent uncontrolled movements. Recommendations are made to use plastic joints, safety clips, and cables to secure hoses and prevent leaks, sparks, or flying debris. Personal protective equipment like hard hats, safety boots, and ear protection are required.
Ma 020 launching lifeboats to sea
This document contains a job safety analysis for launching lifeboats to sea from an offshore drilling rig. It outlines the basic job steps, potential accidents and hazards at each step, and recommendations to reduce risks. The seven steps are: 1) pre-job meeting, 2) opening lifeboat doors and checks, 3) testing operations without personnel, 4) embarking crew, 5) lowering to sea and releasing, 6) testing in sea, and 7) raising back. Hazards include falling overboard, equipment failures, injuries from incorrect procedures. Recommendations focus on wearing lifejackets, checking equipment, going slowly, having competent operators, and getting weather forecasts.
Ma 115 boom crane cable tray repair
1) This Job Safety Analysis document outlines the steps and potential hazards involved in repairing a cable tray using a crane. The work team includes a crane operator and electricians. Required safety equipment includes hard hats, safety boots, gloves, safety glasses, and harnesses.
2) The basic job steps are to hold a pre-job meeting, place the crane boom on a cradle and install planking, secure the cable tray, and remove the planking at the end of the job. Potential hazards addressed are procedures not being understood, crane failure, dropping tools, and tools falling from the boom.
3) Recommendations are provided to take time to ensure the JSA is understood,
Ma 025 transfer casing
This document outlines the steps and potential hazards involved in transferring casing from the pipe rack to the rig floor. It describes lifting the casing joint from the pipe rack to the walkway, then from the walkway to the rig floor using slings. Potential hazards include a casing fall if the sling breaks or someone is hit by a joint. Recommendations are made to check lifting equipment, use tag lines, and have personnel stand clear. When lowering the casing on the ramp, good communication is needed between tugger operators to prevent damage or a casing fall. Ramp stoppers must be correctly installed to reduce protector falls on the ramp. Safety equipment like hard hats and safety glasses are required.
Ma 026 offloading or backloading fuel, base oil, obm
This Job Safety Analysis outlines the steps and potential hazards for transferring fuel, base oil, or oil-based mud between a supply boat and an offshore rig. It identifies safety equipment needed and recommendations to reduce risks. Key steps include inspecting lifting gear, performing radio checks, checking sea conditions, lifting and connecting hoses, monitoring tank levels, and ensuring valves are correctly opened. Potential hazards include hose leaks, spills, falls, and pinch points. Recommendations are made to visually inspect lifting gear, have multiple people connect hoses, wear life vests, limit the number of people signaling the crane operator, and post watchmen to monitor hoses during the transfer.
Ma 029 loading & offloading tubulars from a supply boat
This document outlines the safety procedures for loading and offloading tubulars from a supply vessel using a crane. It identifies potential hazards such as bad weather, equipment failure, and improper signals. It recommends only lifting loads within the crane's capacity, properly maintaining lifting equipment, using the correct number of tag lines to control loads, and never standing under suspended loads. Personal protective equipment like hard hats and safety glasses are required, and a work permit and pre-job meeting should be conducted if the lift is unusual or heavy.
Ma 034 jsa general lifting on the deck
1. The document outlines the job safety analysis for general lifting operations on an oil rig deck. It identifies potential hazards for lifting a load, lowering the load, and storing the load. Recommendations are provided to eliminate or reduce hazards, such as checking lifting equipment, using tag lines, restricting access, and having the deck leader coordinate signals.
2. Personal protective equipment including hard hats, safety boots, gloves, and safety glasses are required. The deck leader and tool pusher are responsible for supervising lifting operations.
3. Job steps, hazards, recommendations, and required safety equipment are documented to ensure lifting operations on the oil rig deck are conducted safely.
Welding operation
This document summarizes the job safety analysis for welding work. It identifies potential accidents and hazards associated with each basic job step, including interference with other operations, electrical shock, cutting/grinding disks breaking, welding/grinding/cutting injuries, fires, and explosions. Recommendations are provided to eliminate or reduce hazards, such as using certified equipment, wearing protective gear, securing work areas, inspecting areas, and having fire watchers and extinguishers. Safety equipment needed includes hard hats, gloves, face shields, boots, vests, goggles, harnesses, barricades, and work permits.
Ma 028 jsa open seachest
This document outlines the steps and potential hazards involved in opening a seachest to inspect an anode and filter. The job safety analysis identifies several potential hazards including pinch points, energized anodes, falling chain blocks, and improper use of tools. Recommendations are provided such as securing equipment properly, cutting power to anodes, and using tools and chain blocks with care to eliminate or reduce hazards. Personal protective equipment including hard hats, safety boots, gloves, and safety glasses are required for the job.
Ma 027 jsa general lifting on the deck
This Job Safety Analysis document summarizes the potential hazards and safety recommendations for lifting loads on deck. It outlines 3 basic job steps: 1) lifting a load from the deck, 2) lowering the load on the deck, and 3) storing the load on the deck. For each step, potential accidents are identified such as a falling or swinging load. Recommendations to reduce hazards include using tag lines, restricting access, and securing loads with blocks. Required safety equipment includes hard hats, safety boots, and barricades.
Ma 024 working on ladder
Crew members will be working on a ladder to perform maintenance tasks. The summary identifies several potential hazards including falls from ladders. Recommendations are provided such as inspecting ladders for defects, using ladders of the appropriate length, securing ladders firmly in place, and using fall protection like safety harnesses while working on ladders. A list of required personal protective equipment is also included.
Ma 038 painting on derrick set
This document outlines the job safety analysis for painting on a derrick. It identifies potential hazards associated with each step of the job and recommendations to reduce risks. Key steps include cleaning the work area, informing the driller, wearing appropriate PPE like gloves and goggles, securing any ladders used, and cleaning up after completion. Falling, paint or dirt in eyes or on skin, and tripping hazards are some potential accidents that proper PPE, harnessing, housekeeping and following procedures seek to eliminate or reduce.
Ma 030 cleaning oil in 100 t crane
The document outlines the steps and potential hazards involved in cleaning oil from a 100-ton crane. It lists the work team as a supervisor and barge master. The key steps are preparing the area, evaluating risks, preparing cleaning materials, and starting the job while wearing proper safety equipment like gloves and safety glasses to prevent spillage of oil. Recommendations are made to remove unnecessary equipment, check materials are in good condition, and dispose of rags properly to reduce slipping hazards and spills.
Ma 036 jsa check ballast 5p loading valve
The document outlines the steps and potential hazards involved in checking a ballast discharge valve on a rig. The key steps are to check that the ballast pumps are off, remove the bolts and valve, and replace the valve. Hazards include water splashing, pinched fingers, and trapped water. Safety recommendations include double checking pumps are off, using tools correctly, and removing the valve slowly and carefully. Required safety equipment includes hard hats, safety boots, gloves, glasses, and a work permit.
Ma 035 jsa open seachest
This document outlines the steps and potential hazards involved in opening a seachest to inspect an anode and filter on Rig BENNEVIS. The key steps are to close valves, remove bolts, open the bleed cock, use a chain block to lift the filter cover, open the cover, inspect the anode and filter, secure everything correctly, and close the cover and install bolts. Potential hazards include pinch points, a falling chain block, an energized anode, and improper use of tools. Recommendations are made to use tools with care, secure the chain block properly, and cut power to the anode before opening the cover. Required safety equipment includes hard hats, safety boots, gloves,
Ma 033 jsa rack pup joint in the stb rack
This document outlines the steps and potential hazards involved in racking a pup joint on an offshore drilling rig's deck. It describes 3 main steps: 1) preparing and lifting the pup joint using a crane, 2) setting the pup joint upright in the deck rack, and 3) unhooking the pup joint from the crane. Potential hazards at each step include people being struck by moving equipment, caught in pinch points, and risks from improper lifting. Recommendations are provided such as using tag lines, barricades, and radios to communicate between workers and reduce hazards. Safety equipment like hard hats and steel-toed boots are also listed.
Ma 039 jsa emergency load lowering
This document outlines the steps and safety procedures for an emergency crane load lowering job. It details 3 steps: 1) lifting the load, 2) lowering the load onto the deck, and 3) securing the load on the deck. Potential hazards are identified for each step such as load fall, personnel being hit or trapped, and load rolling. Recommendations to reduce hazards include checking lifting equipment, attaching tag lines to the load, restricting deck access, using block wedges to secure round loads, and having good communication between crew members. Procedures for manually lowering the load in case of power loss to the crane are also described.
Ma 022 preloading
This job safety analysis document outlines the steps and potential hazards involved in preloading a rig. It identifies 5 basic job steps: 1) holding a pre-job meeting, 2) calculating stability, 3) marking ladder levels, 4) filling preload tanks, and 5) dumping preload tanks. For each step, potential accidents and recommendations to reduce hazards are provided. The document includes information such as required safety equipment, a review date, and approvals.
Ma 021 backload flare boom on supply-boat
This Job Safety Analysis document outlines the steps and potential hazards involved in backloading a flare boom onto a supply boat. It identifies 4 key steps: 1) holding a pre-job meeting to review procedures, 2) preparing and connecting slings to the flare boom, 3) using a crane to shift the flare boom from the main deck, and 4) backloading the flare boom onto the supply boat and disconnecting the slings. For each step, potential accidents and hazards are identified such as crane failure, injury from slings or swinging loads. Recommendations are provided such as inspecting equipment, moving slowly, using tag lines for control, and positioning workers safely.
Ma 019 preloads dump valves maintenance
This Job Safety Analysis document outlines the steps and potential hazards involved in preloading valve maintenance. The four main steps are: 1) holding a pre-job meeting to review procedures, 2) preparing tools and lighting equipment, ensuring correct voltage and securing tools, 3) entering the tank using fall protection and checking for gas, and maintaining the dump valve, and 4) recovering tools and exiting the tank using fall protection and checking that no tools are left behind. Potential hazards addressed at each step include injury from incorrect procedures, tools falling on people, electric shock, falls, pinch points, and improper lighting. Recommendations are provided to eliminate or reduce hazards such as taking time to understand procedures, securing tools, using fall protection, checking
Ma 018 changing lifeboats wires
This document is a Job Safety Analysis for changing lifeboat wires on the rig BENNEVIS. It outlines the basic job steps and identifies potential accidents and hazards at each step. It then provides recommendations to eliminate or reduce those hazards. The six main job steps are: 1) Hold pre-job meeting 2) Prepare tools and wire drums 3) Fix safety slings and disconnect old wire 4) Remove old wire 5) Install new wire 6) Reconnect lifeboat and release slings. Hazards identified include falling, drowning, pinch points, and improper procedures. Recommendations focus on using proper safety equipment, securing tools and wires, and ensuring tasks are performed correctly by qualified personnel.
Ma 017 backloading coiled tubing real on boat
1. This document outlines the job safety analysis for backloading a coiled tubing reel onto a supply boat.
2. It identifies 5 basic job steps and potential accidents/hazards at each step, such as crane failure, equipment damage, and injuries from swinging loads.
3. For each hazard, it provides recommendations to reduce risks, such as inspecting equipment, moving slowly, using tag lines, and designating qualified signalers.
Ma 016 unloading coiled tubing real from boat & install it on cantilever deck
This Job Safety Analysis document outlines the steps and potential hazards involved in unloading coiled tubing from a boat and installing it on a cantilever deck. The six key steps are: 1) holding a pre-job meeting to review procedures, 2) preparing slings to lift the tubing, 3) lifting the tubing onto the main deck with a port crane, 4) transferring the tubing to a starboard crane, 5) shifting the tubing to the cantilever deck, and 6) ending the operation and storing the slings. Potential hazards at each step include crane and sling failures, equipment damage, and injuries from swinging loads. Recommendations are provided to eliminate hazards through
Ma 015 boom crane paint maintenance
1. This Job Safety Analysis outlines the steps and potential hazards for painting the boom of a crane. The work team consists of a crane operator and painters.
2. Some potential hazards identified include crane failure, inhaling spray paint vapors, being hit by a spray gun hose, eye irritation, and tools falling from the boom.
3. Recommendations are provided to eliminate or reduce hazards, such as operating the crane slowly, wearing proper protective equipment, inspecting tools, and cleaning the work area when completed.
Ma 014 changing boom pendants on both cranes
This Job Safety Analysis outlines the steps and potential hazards involved in changing boom pendants on cranes. It identifies 6 key steps: 1) holding a pre-job meeting to review procedures, 2) preparing and inspecting tools, 3) disconnecting the old pendants, 4) removing the old pendants with an opposite crane, 5) installing the new pendants, and 6) raising the crane boom. Potential hazards at each step like falling objects, pinch points, and falling from heights are identified. Recommendations to reduce hazards include properly securing tools and equipment, using fall protection, operating cranes slowly, and not positioning workers in danger zones.
Ma 013 testing lifeboats capsules
This Job Safety Analysis document outlines the steps and potential hazards involved in testing lifeboats on an oil rig. It lists 5 basic job steps: 1) holding a pre-job meeting to ensure all crew understand procedures, 2) preparing and inspecting the lifeboat before launching, 3) lowering the lifeboat, 4) launching the lifeboat, and 5) recovering the lifeboat. For each step, potential accidents are identified such as equipment failure, injuries, or man overboard. Recommendations are provided to eliminate hazards, including regular maintenance, inspection, qualified operators, and standby rescue equipment. Signatures are required to confirm review of safety precautions.
More Related Content
Viewers also liked
Ma 026 offloading or backloading fuel, base oil, obm
This Job Safety Analysis outlines the steps and potential hazards for transferring fuel, base oil, or oil-based mud between a supply boat and an offshore rig. It identifies safety equipment needed and recommendations to reduce risks. Key steps include inspecting lifting gear, performing radio checks, checking sea conditions, lifting and connecting hoses, monitoring tank levels, and ensuring valves are correctly opened. Potential hazards include hose leaks, spills, falls, and pinch points. Recommendations are made to visually inspect lifting gear, have multiple people connect hoses, wear life vests, limit the number of people signaling the crane operator, and post watchmen to monitor hoses during the transfer.
Ma 029 loading & offloading tubulars from a supply boat
This document outlines the safety procedures for loading and offloading tubulars from a supply vessel using a crane. It identifies potential hazards such as bad weather, equipment failure, and improper signals. It recommends only lifting loads within the crane's capacity, properly maintaining lifting equipment, using the correct number of tag lines to control loads, and never standing under suspended loads. Personal protective equipment like hard hats and safety glasses are required, and a work permit and pre-job meeting should be conducted if the lift is unusual or heavy.
Ma 034 jsa general lifting on the deck
1. The document outlines the job safety analysis for general lifting operations on an oil rig deck. It identifies potential hazards for lifting a load, lowering the load, and storing the load. Recommendations are provided to eliminate or reduce hazards, such as checking lifting equipment, using tag lines, restricting access, and having the deck leader coordinate signals.
2. Personal protective equipment including hard hats, safety boots, gloves, and safety glasses are required. The deck leader and tool pusher are responsible for supervising lifting operations.
3. Job steps, hazards, recommendations, and required safety equipment are documented to ensure lifting operations on the oil rig deck are conducted safely.
Welding operation
This document summarizes the job safety analysis for welding work. It identifies potential accidents and hazards associated with each basic job step, including interference with other operations, electrical shock, cutting/grinding disks breaking, welding/grinding/cutting injuries, fires, and explosions. Recommendations are provided to eliminate or reduce hazards, such as using certified equipment, wearing protective gear, securing work areas, inspecting areas, and having fire watchers and extinguishers. Safety equipment needed includes hard hats, gloves, face shields, boots, vests, goggles, harnesses, barricades, and work permits.
Ma 028 jsa open seachest
This document outlines the steps and potential hazards involved in opening a seachest to inspect an anode and filter. The job safety analysis identifies several potential hazards including pinch points, energized anodes, falling chain blocks, and improper use of tools. Recommendations are provided such as securing equipment properly, cutting power to anodes, and using tools and chain blocks with care to eliminate or reduce hazards. Personal protective equipment including hard hats, safety boots, gloves, and safety glasses are required for the job.
Ma 027 jsa general lifting on the deck
This Job Safety Analysis document summarizes the potential hazards and safety recommendations for lifting loads on deck. It outlines 3 basic job steps: 1) lifting a load from the deck, 2) lowering the load on the deck, and 3) storing the load on the deck. For each step, potential accidents are identified such as a falling or swinging load. Recommendations to reduce hazards include using tag lines, restricting access, and securing loads with blocks. Required safety equipment includes hard hats, safety boots, and barricades.
Ma 024 working on ladder
Crew members will be working on a ladder to perform maintenance tasks. The summary identifies several potential hazards including falls from ladders. Recommendations are provided such as inspecting ladders for defects, using ladders of the appropriate length, securing ladders firmly in place, and using fall protection like safety harnesses while working on ladders. A list of required personal protective equipment is also included.
Ma 038 painting on derrick set
This document outlines the job safety analysis for painting on a derrick. It identifies potential hazards associated with each step of the job and recommendations to reduce risks. Key steps include cleaning the work area, informing the driller, wearing appropriate PPE like gloves and goggles, securing any ladders used, and cleaning up after completion. Falling, paint or dirt in eyes or on skin, and tripping hazards are some potential accidents that proper PPE, harnessing, housekeeping and following procedures seek to eliminate or reduce.
Ma 030 cleaning oil in 100 t crane
The document outlines the steps and potential hazards involved in cleaning oil from a 100-ton crane. It lists the work team as a supervisor and barge master. The key steps are preparing the area, evaluating risks, preparing cleaning materials, and starting the job while wearing proper safety equipment like gloves and safety glasses to prevent spillage of oil. Recommendations are made to remove unnecessary equipment, check materials are in good condition, and dispose of rags properly to reduce slipping hazards and spills.
Ma 036 jsa check ballast 5p loading valve
The document outlines the steps and potential hazards involved in checking a ballast discharge valve on a rig. The key steps are to check that the ballast pumps are off, remove the bolts and valve, and replace the valve. Hazards include water splashing, pinched fingers, and trapped water. Safety recommendations include double checking pumps are off, using tools correctly, and removing the valve slowly and carefully. Required safety equipment includes hard hats, safety boots, gloves, glasses, and a work permit.
Ma 035 jsa open seachest
This document outlines the steps and potential hazards involved in opening a seachest to inspect an anode and filter on Rig BENNEVIS. The key steps are to close valves, remove bolts, open the bleed cock, use a chain block to lift the filter cover, open the cover, inspect the anode and filter, secure everything correctly, and close the cover and install bolts. Potential hazards include pinch points, a falling chain block, an energized anode, and improper use of tools. Recommendations are made to use tools with care, secure the chain block properly, and cut power to the anode before opening the cover. Required safety equipment includes hard hats, safety boots, gloves,
Ma 033 jsa rack pup joint in the stb rack
This document outlines the steps and potential hazards involved in racking a pup joint on an offshore drilling rig's deck. It describes 3 main steps: 1) preparing and lifting the pup joint using a crane, 2) setting the pup joint upright in the deck rack, and 3) unhooking the pup joint from the crane. Potential hazards at each step include people being struck by moving equipment, caught in pinch points, and risks from improper lifting. Recommendations are provided such as using tag lines, barricades, and radios to communicate between workers and reduce hazards. Safety equipment like hard hats and steel-toed boots are also listed.
Ma 039 jsa emergency load lowering
This document outlines the steps and safety procedures for an emergency crane load lowering job. It details 3 steps: 1) lifting the load, 2) lowering the load onto the deck, and 3) securing the load on the deck. Potential hazards are identified for each step such as load fall, personnel being hit or trapped, and load rolling. Recommendations to reduce hazards include checking lifting equipment, attaching tag lines to the load, restricting deck access, using block wedges to secure round loads, and having good communication between crew members. Procedures for manually lowering the load in case of power loss to the crane are also described.
Viewers also liked (13)
Ma 026 offloading or backloading fuel, base oil, obm
Ma 026 offloading or backloading fuel, base oil, obm
Ma 029 loading & offloading tubulars from a supply boat
Ma 029 loading & offloading tubulars from a supply boat
More from Yousif Fikry
Ma 022 preloading
This job safety analysis document outlines the steps and potential hazards involved in preloading a rig. It identifies 5 basic job steps: 1) holding a pre-job meeting, 2) calculating stability, 3) marking ladder levels, 4) filling preload tanks, and 5) dumping preload tanks. For each step, potential accidents and recommendations to reduce hazards are provided. The document includes information such as required safety equipment, a review date, and approvals.
Ma 021 backload flare boom on supply-boat
This Job Safety Analysis document outlines the steps and potential hazards involved in backloading a flare boom onto a supply boat. It identifies 4 key steps: 1) holding a pre-job meeting to review procedures, 2) preparing and connecting slings to the flare boom, 3) using a crane to shift the flare boom from the main deck, and 4) backloading the flare boom onto the supply boat and disconnecting the slings. For each step, potential accidents and hazards are identified such as crane failure, injury from slings or swinging loads. Recommendations are provided such as inspecting equipment, moving slowly, using tag lines for control, and positioning workers safely.
Ma 019 preloads dump valves maintenance
This Job Safety Analysis document outlines the steps and potential hazards involved in preloading valve maintenance. The four main steps are: 1) holding a pre-job meeting to review procedures, 2) preparing tools and lighting equipment, ensuring correct voltage and securing tools, 3) entering the tank using fall protection and checking for gas, and maintaining the dump valve, and 4) recovering tools and exiting the tank using fall protection and checking that no tools are left behind. Potential hazards addressed at each step include injury from incorrect procedures, tools falling on people, electric shock, falls, pinch points, and improper lighting. Recommendations are provided to eliminate or reduce hazards such as taking time to understand procedures, securing tools, using fall protection, checking
Ma 018 changing lifeboats wires
This document is a Job Safety Analysis for changing lifeboat wires on the rig BENNEVIS. It outlines the basic job steps and identifies potential accidents and hazards at each step. It then provides recommendations to eliminate or reduce those hazards. The six main job steps are: 1) Hold pre-job meeting 2) Prepare tools and wire drums 3) Fix safety slings and disconnect old wire 4) Remove old wire 5) Install new wire 6) Reconnect lifeboat and release slings. Hazards identified include falling, drowning, pinch points, and improper procedures. Recommendations focus on using proper safety equipment, securing tools and wires, and ensuring tasks are performed correctly by qualified personnel.
Ma 017 backloading coiled tubing real on boat
1. This document outlines the job safety analysis for backloading a coiled tubing reel onto a supply boat.
2. It identifies 5 basic job steps and potential accidents/hazards at each step, such as crane failure, equipment damage, and injuries from swinging loads.
3. For each hazard, it provides recommendations to reduce risks, such as inspecting equipment, moving slowly, using tag lines, and designating qualified signalers.
Ma 016 unloading coiled tubing real from boat & install it on cantilever deck
This Job Safety Analysis document outlines the steps and potential hazards involved in unloading coiled tubing from a boat and installing it on a cantilever deck. The six key steps are: 1) holding a pre-job meeting to review procedures, 2) preparing slings to lift the tubing, 3) lifting the tubing onto the main deck with a port crane, 4) transferring the tubing to a starboard crane, 5) shifting the tubing to the cantilever deck, and 6) ending the operation and storing the slings. Potential hazards at each step include crane and sling failures, equipment damage, and injuries from swinging loads. Recommendations are provided to eliminate hazards through
Ma 015 boom crane paint maintenance
1. This Job Safety Analysis outlines the steps and potential hazards for painting the boom of a crane. The work team consists of a crane operator and painters.
2. Some potential hazards identified include crane failure, inhaling spray paint vapors, being hit by a spray gun hose, eye irritation, and tools falling from the boom.
3. Recommendations are provided to eliminate or reduce hazards, such as operating the crane slowly, wearing proper protective equipment, inspecting tools, and cleaning the work area when completed.
Ma 014 changing boom pendants on both cranes
This Job Safety Analysis outlines the steps and potential hazards involved in changing boom pendants on cranes. It identifies 6 key steps: 1) holding a pre-job meeting to review procedures, 2) preparing and inspecting tools, 3) disconnecting the old pendants, 4) removing the old pendants with an opposite crane, 5) installing the new pendants, and 6) raising the crane boom. Potential hazards at each step like falling objects, pinch points, and falling from heights are identified. Recommendations to reduce hazards include properly securing tools and equipment, using fall protection, operating cranes slowly, and not positioning workers in danger zones.
Ma 013 testing lifeboats capsules
This Job Safety Analysis document outlines the steps and potential hazards involved in testing lifeboats on an oil rig. It lists 5 basic job steps: 1) holding a pre-job meeting to ensure all crew understand procedures, 2) preparing and inspecting the lifeboat before launching, 3) lowering the lifeboat, 4) launching the lifeboat, and 5) recovering the lifeboat. For each step, potential accidents are identified such as equipment failure, injuries, or man overboard. Recommendations are provided to eliminate hazards, including regular maintenance, inspection, qualified operators, and standby rescue equipment. Signatures are required to confirm review of safety precautions.
Ma 012 using working personnel basket
This Job Safety Analysis document outlines the steps and potential hazards involved in using a working basket from a crane. It identifies 4 basic job steps: 1) holding a pre-job meeting to review procedures, 2) preparing the working basket and safety equipment, 3) moving personnel in the basket, and 4) lowering the basket at the end of the job. For each step, potential accidents are listed such as injuries from incorrect procedures, damaged equipment, and improper crane signals. Recommendations are provided to eliminate hazards, such as inspecting equipment, learning signals, and only having one person direct the crane operator. The document was prepared by the company's QA/HSE department and approved by an H.M.
Ma 011 crane wire replacement ( main hook line )
This document outlines the job safety analysis for replacing the main hook line on the BENNEVIS drilling rig. It identifies 8 basic job steps and potential accidents/hazards for each step. Recommendations are provided to eliminate or reduce hazards, including using proper safety equipment, preparing tools correctly, operating the crane slowly, securing wires, and cleaning up work areas. A work team is identified and each step requires sign-off by supervisors to ensure safety procedures are followed.
More from Yousif Fikry (11)
Ma 016 unloading coiled tubing real from boat & install it on cantilever deck
Ma 016 unloading coiled tubing real from boat & install it on cantilever deck
Ma 032 transfer water from or to supply boat
- 1. Rig #: BENNEVIS PIC Signature Approving JSA: Work Activity (Job): MA 032 RECEIVE WATER FROM SUPPLY BOAT Work Team (Crew Members): BARGEMASTER – CRANE OP. --ROUSTABOUT Sequence of Basic Job Steps Potential Accidents or Hazards Recommendation to Eliminate or Reduce Potential Hazards Who? Initials - CONNECT HOSE TO CRANE HOOK - LIFT HOSE TO BOAT - HOSE CAN FALL IN SEA - CONDITION OF HOSE - PINCH POINTS - HOSE CAN FALL IN SEA - PINCH POINTS - CHECK LIFTING POINT - MIN 2 PERSONS TO CONNECT & CONTROLHOOK - INSPECT HOSE BEFORE CONNECTING - TAKE CARE WHEN CONNECTING - TAKE CARE WHEN RELEASING HANG OFF ROPES - START TRANSFER - HOSE BLOCKED - HOSE BURST - WRONG TANK LINED UP - ENSURE ALL RELEVANT VALVES ARE OPEN - INFORM CAPT. OF BOAT TO START PUMPING - MONITOR HOSE AT FREQUENT - INTERVALS - RETURN HOSE TO RIG - HOSE LEAKS - BOAT LOOSE CONTROL IN CURRENT - HOSE FALL IN SEA - ROUSTABOUT FALL OVERBOARD - INFORM CAPT OF ABNORMAL WIND OR CURRENT CHANGE - ENSURE LIFTING SLING CORRECTLY CONNECTED - WEAR WORKVEST, DON’T STAND ON HANDRAILS WHEN RECONNECTING TO RIG Safety Equipment To Do This Job Hard Hats ( Cotton Gloves ( Face Shield ( Fire Extinguishers ( Safety Boots ( Work Vest ( Goggles ( Lockout/Tagout ( Safety Glasses ( Safety Harness ( Barricades ( Work Permit Required ( Uncontrolled When Printed Page 1 Pyramid Drilling S.A Manual Title: Personnel Safety Manual Form Name: Job Safety Analysis Issue Date 02-Sept-07 Revision No. 2 Revision Date 04-MAR 08 Prepared By QA/HSE Approved By HM Level No. 2
- 2. Uncontrolled When Printed Page 2 Pyramid Drilling S.A Manual Title: Personnel Safety Manual Form Name: Job Safety Analysis Issue Date 02-Sept-07 Revision No. 2 Revision Date 04-MAR 08 Prepared By QA/HSE Approved By HM Level No. 2