SlideShare a Scribd company logo
7" Portable On-camera LCD Monitor 
User Manual 
Model: DT-X71F HDSDI&HDMI, Waveform, Audio meter, Focus assist 
DT-X71H 3GSDI&HDMI 
DT-X71C HDMI 
Please read this User Manual 
throughout before using.
Preface 
Congratulations on your purchase of this product. Please read this user manual carefully. 
1 
. 
All internal technologies of this product are protected, including device, software and trademark. 
Reproduction in whole or in part without written permission is prohibited. 
2 
. 
All brands and trademarks are protected and other relative trademarks in this user manual are the 
properties of their respective owners. 
3 
. 
Due to constant effort of product development, SWIT Electronics reserves the right to make changes and 
improvements to the product described in this manual without prior notice. 
4 
. 
The warranty period of this product is 2 years, and does not cover the following: 
(1) Physical damage to the surface of the products, including scratches, cracks or other damage to the 
LCD screen or other externally exposed parts; 
(2) Misuse, abuse or negligent operation to the product; 
(3) The product is disassembled by anyone other than an authorized service center. 
It is considered normal that the LCD bright dot defects are not to exceed three. 
5 
. 
For any suggestions and requirements on this product, please contact us through phone, fax, Email, etc. 
SWIT Electronics Co., Ltd. / SWIT Electronics USA, LLC. 
Address: 4300 Stevens Creek Blvd. Suite 230 
San Jose, CA 95129 
Toll free: 1 866 986-SWIT(7948) 
Tel: 408 260-8258 
Fax: 408 228-8438 
Email: info@swit.us 
Website: www.swit.us
Maintenance 
 Monitor 
1. Please keep the signal terminals and the cooling vent away from knife-edge, metal or liquid in order to 
avoid short-circuit and damage. 
2. Please don't try to disassemble any parts of the monitor by yourself, which would probably damage the 
monitor and do harm to human body, and it will cause the invalidation of product warranty. 
3. Please don't touch the screen with your fingers, which would probably deface the screen. 
4. Please don't press the screen; the LCD is extremely exquisite and flimsy. 
 The power 
Please use the provided power adapter or the battery recommended by the manufacturer in order to 
avoid damage. For a third party power adapter, please make sure the voltage range, supplied power, and 
polarity of power lead are fit. 
Please disconnect the power cable or take off the battery under the following situations: 
1. If you do not operate this monitor for a period of time; 
2. If the power cable or power adaptor is damaged; 
3. If the monitor housing is broken. 
 Working Environment 
1. Please don't lay this product on the unstable place. 
2. Please don't lay this product in hot, cold or wet location. 
 Cleaning 
1. Please clean the screen with dry and downy cloth or special LCD cleanser. 
2. Please do not press hard when cleaning the screen. 
3. Please do not use water or other chemical cleanser to clean the screen. The chemical may damage 
the LCD. 
4. For first time use, please tear off the factory LCD film. To protect the LCD screen, please post the LCD 
protection film offered in the package.
1. Features 
DT-X71F 
New high resolution 7” LCD Panel 
16:9, 1024×600, 16.77 million colors, 900:1 
contrast, and H160 
° 
◆ 
/ V160 
° 
viewing angle. 
Multiple inputs 
2 HD/SD-SDI, 1 HDMI and 1 Composite input. 
◆ 
◆ 
Loop through outputs 
Each of the 2 input HD/SD-SDI has loop through 
output. 
◆ 
HDMI converted to SDI output 
Supported HDMI formats: 480i / 576i / 720p (50, 
59.94, 60) / 1080i (50, 59.94, 60) / 1080P (23.98 
24, 25, 29.97, 30), and the output SDI will embed 
the audio (48KHz) from HDMI. 
◆ 
Waveform (Y, Cb, Cr, R, G, B) and full scale 
There are totally 6 kinds of waveform display, 
available under both SDI and HDMI, to check the 
Luminance (Y), Blue-difference (Cb), 
Red-difference (Cr), Red (R), Green (G), Blue (B), 
and the Y, Cb, Cr can be simultaneously displayed, 
R, G, B can be simultaneously displayed, and 
each of the waveforms can be set to full scale 
display. 
◆ 
Vector scope 
The displayed vector scope pattern is available 
under both SDI and HDMI, represents saturation 
as distance from the center of the circle, and hue 
as the angle, in standard position, around it. 
◆ 
Histogram (R, G, B) 
The histogram is a bar graph that shows the 
distribution of luminance values in the picture. 
There’re R, G, B histograms that individually 
displayed simultaneously, available under both 
SDI and HDMI. 
◆ 
16-ch audio meter 
Under HDSDI, it displays 16 channels audio bars, 
with mark, and under SDSDI or HDMI, it displays 
2 channels audio bars with mark. The audio bar is 
green, and will turn yellow when audio exceeds 
-20dB, and turn red when exceeds -10dB. 
SDI timecode 
◆ 
Under SDI input, it can display the SMPTE 
timecode, which is used extensively for 
synchronization, and for logging and identifying 
material in recorded media. 
Peaking focus assist (red/blue switch) 
◆ 
The Peaking focus assist function is to mark the 
sharpest edges of the image with red or blue color, 
for users to check if the subjects are focused. 
◆ 
Zebra stripes 
Zebra Stripes are used to check if the image is 
over exposed or not by showing black and white 
lines on the monitor. It is considered over exposed 
when luminance value exceeds 90%. 
◆ 
False color 
The false color is used to aid in the setting of 
camera exposure. Under false color mode, there’s 
a false color key on the bottom of screen for 
reference. The over exposed subjects (above 101 
IRE) on the monitor will display as RED, and the 
underexposed subjects will display as BLUE. For 
correct exposed subjects, it will display as green 
and pink. 
◆ 
Blue Only 
Under the Blue Only Mode, only the blue pixels 
are used to generate the image, because hue and 
saturation can be adjusted quicker and more 
accurately. 
◆ 
DSLR scale zoom in 
The Canon DSLR outputs the CMOS sensor ratio 
HDMI and this zoom in mode can make the 
effective image scale full screen on the monitor. 
◆ 
User definable function keys 
There are 3 function keys on the monitor front 
panel, that permit users to define shortcuts for the 
various functions. 
◆ 
User editable video title 
User can edit a video title for the current camera, 
and the title will display on the top of screen. 
◆ 
Front and Rear 3-color TALLY light 
2 TALLY lights design, to give “live” signals to 
people in front of the camera, as well as the 
camera operator behind. 
Image Flip 
◆ 
Set image to rotate by 180 
. 
°
DT-X71H 
High resolution 7” LCD Panel 
16:9, 1024×600, 16.77 million colors, 900:1 
contrast, and H160 
° 
◆ 
/ V160 
° 
viewing angle. 
3Gbps SDI support 
Accepts 3G/HD/SD-SDI input. 
◆ 
◆ 
Multiple inputs 
1 3G/HD/SD-SDI, 1 HDMI, 1 Composite input 
and L/R stereo audio. 
◆ 
Loop through outputs 
1 3G/HD/SD-SDI, 1 HDMI and 1 Composite video 
loop through output. 
◆ 
SDI embedded audio output 
The SDI embedded audio can be output through 
3.5mm earphone on the front panel. 
Image Flip. 
◆ 
Set image to rotate by 180 
° 
DSLR scale zoom in 
◆ 
The Canon DSLR outputs the CMOS sensor ratio 
HDMI and this zoom in mode can make the 
effective image scale full screen on the monitor. 
◆ 
User definable function keys 
There are 2 function keys on the monitor front 
panel, that permit users to define shortcuts for the 
various functions. 
◆ 
User editable video title 
User can edit a video title for the current camera, 
and the title will display on the top of screen. 
Front and Rear 3-color TALLY light 
◆ 
2 TALLY lights design, to give “live” signals to 
people in front of the camera, as well as the 
camera operator behind. 
DT-X71C 
New high resolution 7” LCD Panel 
16:9, 1024×600, 16.77 million colors, 900:1 
contrast, and H160 
° 
◆ 
/ V160 
° 
viewing angle. 
Multiple inputs 
1 HDMI, 1 Composite input 
and L/R stereo audio input. 
◆ 
◆ 
Loop through outputs 
1 HDMI and 1 Composite loop through output. 
◆ 
DSLR scale zoom in 
The Canon DSLR outputs the CMOS sensor ratio 
HDMI and this zoom in mode can make the 
effective image scale full screen on the monitor. 
Image Flip 
◆ 
Set image to rotate by 180 
. 
° 
User definable function keys 
◆ 
There are 2 function keys on the monitor front 
panel, that permit users to define shortcuts for the 
various functions. 
◆ 
User editable video title 
User can edit a video title for the current camera, 
and the title will display on the top of screen. 
Front and Rear 3-color TALLY light 
◆ 
2 TALLY lights design, to give “live” signals to 
people in front of the camera, as well as the 
camera operator behind.
2. Panel Instruction 
DT-X71F 
Front view 
PHONE: Earphone jack 
⑵ 
⑴ 
POWER: Power on/off 
Connect with power cable or mount battery, press the “POWER” and the power indicator is turned on 
and after 10 seconds, the monitor will be switched on and get into normal working status. Press the 
“POWER” again, the indicator is turned off and monitor is switched off. 
Disconnect with power cable or take off the battery if the monitor will not be used for a period of time. 
IN: Input signal selection 
⑶ 
Press “IN” and revolve the “OK” to select the input video signal. 
⑷ 
F1: User definable function key 1 
FOCUS: Peaking Focus Assist 
⑸ 
Press “FOCUS” once, it will display the current peaking on/off status. Press “FOCUS” again to switch 
on RED line focus assist, switch on BLUE line focus assist, and switch off in turn. 
F.COLOR: False color 
⑹ 
Press “F.COLOR” once, it will display the current false color on/off status. Press “F.COLOR” again to 
switch on/off the false color mode. 
DISPLAY: Display current settings 
⑺ 
Press “Display” to display safety mark, title and the current input signal information 
⑻ 
F2: User definable function key 2 
⑼ 
F3: User definable function key 3 
WAVEFORM: Display waveform 
⑽ 
Press “WAVEFORM” once, it will display the waveform menu as: 
Revolve “OK” to select a waveform display mode and turn it on. 
The selected waveform will display on the screen. 
⑾ 
VECTOR: Display vector scope 
Press “VECTOR” to switched on/off the Vector scope 
⑿ 
MENU: Press to enter Menu 
OK: Select and Apply 
⒀ 
Under menu system, revolve “OK” to adjust settings and press to apply; and out of menu system, 
directly revolve “OK” to adjust volume. 
TALLY Light: Red, Green and Yellow 3-color TALLY indicator 
⒁
Rear view 
DC 12V IN: Connect with DC12V 4-pin XLR power adapter. 
⑵ 
⑴ 
TALLY Light: Red, Green and Yellow 3-color TALLY indicator 
Battery mount: 
⑶ 
Connect with JVC battery BN-VF823 or SWIT battery BN-S8823 to power the monitor. 
⑷ 
HDSDI IN1/2: HD/SD-SDI input (BNC connector) 
⑸ 
HDSDI OUT: HDMI converted to SDI output (BNC connector) 
⑹ 
HDSDI LOOP1/2: HD/SD-SDI loop through output (BNC connector) 
⑺ 
VIDEO IN: Composite video input (BNC connector) 
⑻ 
TALLY controlling port (RJ45): terminal description is as follows: 
The RED light is on when connecting the terminal “R” with “GND”, and goes out when disconnecting. 
The GREEN light is on when connecting the terminal “G” with “GND”, and goes out when disconnecting. 
The YELLOW light is on when connecting the terminal “Y” with “GND”, and goes out when disconnecting 
HDMI: HDMI input 
⑼ 
Input formats 
Terminal 1 2 3 4 5 6 7 8 
Description Y G GND R 
Input Supported formats 
CVBS PAL / NTSC 
480I / 576I / 480P / 576P 
1080i (60 / 59.94 / 50) 
720p (60 / 59.94 / 50) 
HDMI 
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98) 
1080i (60 / 59.94 / 50) 
SMPTE-274M 
1080p (30 / 29.97 / 25 / 24 / 23.98) 
SMPTE-296M 720p (60 / 59.94 / 50) 
SMPTE-125M 480i (59.94) 
SDI 
ITU-R BT.656 576i (50)
DT-X71H 
Front view 
PHONE: Earphone jack, for SDI embedded audio, HDMI audio and analog audio 
⑵ 
⑴ 
POWER: Power on/off 
Connect with power cable or mount battery, press the “POWER” and the power indicator is turned on and 
after 10 seconds, the monitor will be switched on and get into normal working status. Press the “POWER” 
again, the indicator is turned off and monitor is switched off. 
Remark: Disconnect with power cable or take off the battery if the monitor will not be used for a period of 
time. 
⑶ 
CVBS: Press to switch the input signal to Composite video 
⑷ 
HDMI: Press to switch the input signal to HDMI 
⑸ 
SDI: Press to switch the input signal to SDI 
⑹ 
OVERSCAN: Overscan / Underscan switch 
⑺ 
MENU: Press to enter Menu 
⑻ 
F1: User definable function key 1 
⑼ 
F2: User definable function key 2 
⑽ 
RATIO: 16:9 and 4:3 switch 
ZOOM: 
Picture Zoom-in 
⑾ 
Press “ZOOM” to switch ZOOM1: Canon DSLR scale zoom-in, and ZOOM2: pixel to pixel zoom-in. 
DISPLAY: Display current settings 
⑿ 
Press “Display” to display safety mark, title and the current input signal information 
OK: Select and Apply 
⒀ 
Under menu system, revolve “OK” to adjust settings and press to apply; and out of menu system, 
directly revolve “OK” to adjust volume. 
TALLY Light: Red, Green and Yellow 3-color TALLY indicator 
⒁
Rear view 
DC 12V IN: Connect with DC12V 4-pin XLR power adapter. 
⑵ 
⑴ 
TALLY Light: Red, Green and Yellow 3-color TALLY indicator 
Battery mount: 
⑶ 
Connect with JVC battery BN-VF823 or SWIT battery BN-S8823 to power the monitor. 
⑷ 
CVBS IN: Composite video input (BNC connector) 
⑸ 
SDI-LOOP: 3G/HD/SD-SDI loop through output (BNC connector) 
⑹ 
SDI-IN: 3G/HD/SD-SDI input (BNC connector) 
⑺ 
HDMI-LOOP: HDMI loop through output 
⑻ 
HDMI-IN: HDMI input 
⑼ 
TALLY controlling port (RS-232): terminal description is as follows: 
The RED light is on when connecting the terminal “R” with “GND”, and goes out when disconnecting. 
The GREEN light is on when connecting the terminal “G” with “GND”, and goes out when disconnecting. 
The YELLOW light is on when connecting the terminal “Y” with “GND”, and goes out when disconnecting. 
⑽ 
AUDIO L: Stereo audio left channel input (RCA connector) 
⑾ 
AUDIO R: Stereo audio right channel input (RCA connector) 
⑿ 
CVBS-LOOP: Composite video loop through output (BNC connector) 
Input formats 
Terminal 1 2 3 4 5 6 7 8 9 
Description Y G R GND GND GND 
Input Supported formats 
CVBS PAL / NTSC 
480I / 576I / 480P / 576P 
1080i (60 / 59.94 / 50) 
720p (60 / 59.94 / 50) 
HDMI 
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98) 
SMPTE-425M 1080p (60 / 59.94 / 50) 
1080i (60 / 59.94 / 50) 
SMPTE-274M 
1080p (30 / 29.97 / 25 / 24 / 23.98) 
SMPTE-296M 720p (60 / 59.94 / 50) 
SMPTE-125M 480i (59.94) 
SDI 
ITU-R BT.656 576i (50)
DT-X71C 
Front view 
PHONE: Earphone jack 
⑵ 
⑴ 
POWER: Power on/off 
Connect with power cable or mount battery, press the “POWER” and the power indicator is turned on 
and after 10 seconds, the monitor will be switched on and get into normal working status. Press the 
“POWER” again, the indicator is turned off and monitor is switched off. 
Remark: Disconnect with power cable or take off the battery if the monitor will not be used for a period of 
time. 
⑶ 
VIDEO: Press to switch the input signal to Composite video 
⑷ 
HDMI: Press to switch the input signal to HDMI 
⑸ 
B/W: Black and White mode 
⑹ 
OVERSCAN: Overscan / Underscan switch 
⑺ 
MENU: Press to enter Menu 
⑻ 
F1: User definable function key 1 
⑼ 
F2: User definable function key 2 
⑽ 
RATIO: 16:9 and 4:3 switch 
ZOOM: 
Picture Zoom-in 
⑾ 
Press “ZOOM” to switch ZOOM1: Canon DSLR scale zoom-in, and ZOOM2: pixel to pixel zoom-in. 
DISPLAY: Display current settings 
⑿ 
Press “Display” to display safety mark, title and the current input signal information 
⒀ 
OK: Select and Apply 
Under menu system, revolve “OK” to adjust settings and press to apply; and out of menu system, directly 
revolve “OK” to adjust volume. 
TALLY Light: Red, Green and Yellow 3-color TALLY indicator 
⒁
Rear view 
DC 12V IN: Connect with DC12V 4-pin XLR power adapter. 
⑵ 
⑴ 
TALLY Light: Red, Green and Yellow 3-color TALLY indicator 
⑶ 
Battery mount: 
Connect with JVC battery BN-VF823 or SWIT battery BN-S8823 to power the monitor. 
⑷ 
CVBS IN: Composite video input (BNC connector) 
⑸ 
HDMI-LOOP: HDMI loop through output 
⑹ 
HDMI: HDMI input 
⑺ 
TALLY controlling port (RS-232): terminal description is as follows: 
The RED light is on when connecting the terminal “R” with “GND”, and goes out when disconnecting. 
The GREEN light is on when connecting the terminal “G” with “GND”, and goes out when disconnecting. 
The YELLOW light is on when connecting the terminal “Y” with “GND”, and goes out when disconnecting 
⑻ 
AUDIO L: Stereo audio L input (RCA connector) 
⑼ 
AUDIO R: Stereo audio R input (RCA connector) 
⑽ 
CVBS-LOOP: Composite video loop through output (BNC connector) 
Input formats 
Terminal 1 2 3 4 5 6 7 8 9 
Description Y G R GND GND GND 
Input Supported formats 
CVBS PAL / NTSC 
480I / 576I / 480P / 576P 
1080i (60 / 59.94 / 50) 
720p (60 / 59.94 / 50) 
HDMI 
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)
3. Menu Operation 
Press “MENU” and it will display menu system 
 Revolve “OK” to select an item. The selected item will be highlighted display. 
 Press “OK” to enter the selected item. 
 Under menu system, press “MENU” to back to previous menu. 
 The menu will automatically save and quit if it remains idle. 
4. Picture Settings Submenu 
The Picture Settings Submenu includes: 
⑴ 
CONTRAST: 0-100 value adjustment 
⑵ 
BRIGHTNESS: 0-100 value adjustment 
⑶ 
HUE: 0-100 value adjustment 
(Only available under Composite input) 
⑷ 
SATURATION: 0-100 value adjustment 
⑸ 
SHARPNESS: 0-100 value adjustment 
⑹ 
PIC.MODE: User defined and preset picture 
modes: standard, soft and vivid selection 
5. System Configuration Submenu 
The System Configuration Submenu includes: 
⑴ 
RATIO: Select “16:9” or “4:3” to adjust the aspect ratio. 
⑵ 
SCAN: “UNDERSCAN” / “OVERSCAN” selection 
ZOOM: “OFF”, “ZOOM1” and “ZOOM2” selection 
⑶ 
ZOOM1: Canon DSLR scale zoom-in 
ZOOM2: Pixel to Pixel zoom-in 
⑷ 
MARKER: Select and set the safety mark 
scale from 80%, 85%, 90% and 95%. 
FLIP: Select “YES” to flip the image by 180 
. 
⑸ 
° 
⑹ 
RESET: Revolve “OK” to RESET and press to 
recover all to factory setting.
6. OSD Settings Submenu 
The OSD Settings Submenu includes: 
⑴ 
LANGUAGE: Menu language English / Chinese selection 
⑵ 
H-POSITION: Menu horizontal position (0-100) adjustment, real-time preview, default value: 50, center. 
⑶ 
V-POSITION: Menu vertical position (0-100) adjustment, real-time preview, default value: 50, center. 
DURATION: Menu timeout setting 
⑷ 
Set a time (in seconds) in which the menu 
will automatically quit if remains idle. 
Default: 10 seconds; Range: 5 seconds to 
60 seconds. 
7. Title Settings Submenu 
Revolve OK button to select the letters, and press OK to input. Select SPACE to input space and DEL to 
delete the left letter. Max 10 letters are supported. 
After setting, press MENU, the system will 
save data to current user and quit menu. The 
menu will automatically save and quit if it 
remains idle. 
8. Display Settings Submenu 
The DISPLAY settings submenu is to select the 
items to be displayed on screen when 
‘DISPLAY” button is pressed. Revolve OK to 
turn on/off the items: 
(1) INFO: Including Input format, aspect ratio, 
underscan/overscan, zoom status 
(2) MARKER: Safety mark 
(3) TITLE: User edited title
9. FUNCTION KEY Settings Submenu 
The F KEY Settings Submenu is to define 
Function Keys on the front keyboard. 
The DT-X71F has 3 function keys: 
F1, F2 and F3; 
The DT-X71H and DT-X71C has 2 function 
keys: 
F1 and F2. 
The available function items of each model are: 
-------------------DT-X71F------------------- -------------------DT-X71H------------------- 
01-RATIO: Aspect ratio switch 01-RATIO: Aspect ratio switch 
02-SCAN: Underscan / Overscan switch 02-SCAN: Underscan / Overscan switch 
03-ZOOM: Picture Zoom-in 03-ZOOM: Picture Zoom-in 
04-PIC. MODE: Preset picture mode switch 04-B/W: Color / Black  white switch 
05-B/W: Color / Black  white switch 05-FLIP: Image flip 
06-BLUE ONLY: Blue only mode switch on/off 
07-ZEBRA: Zebra over exposure switch on/off 
08-VECTOR: Vector scope switch on/off 
09-PATTERN: Internal colorbar switch on/off -------------------DT-X71C------------------- 
10-RGB HIST: R, G, B Histogram switch on/off 01-RATIO: Aspect ratio switch 
11-TIMECODE: SDI timecode display switch on/off 02-SCAN: Underscan / Overscan switch 
12-F.COLOR: False color mode switch on/off 03-ZOOM: Picture Zoom-in 
13-AUDIO BAR: Audio meter display switch on/off 04-B/W: Color / Black  white switch 
14-FOCUS: Peaking focus assist switch on/off, and 05-FLIP: Image flip 
red/blue selection 
15-FLIP: Image flip
10. Specifications 
LCD Performance 
Size 7.0 inches 
Resolution 1024 
RGB 
× 
× 
600 
Aspect ratio 16:9/4:3 
Color system NTSC/PAL 
Brightness 400cd/m2 
Contrast 900:1 
Color 16.77 million colors 
Viewing angle H/V:160/160 
Video Format 
SMPTE-425M ** 1080p (60 / 59.94 / 50) 
1080i (60 / 59.94 / 50) 
SMPTE-274M 
1080p (30 / 29.97 / 25 / 24 / 23.98) 
SMPTE-296M 720p (60 / 59.94 / 50) 
SMPTE-125M 480i (59.94) 
SDI * 
ITU-R BT.656 576i (50) 
480I / 576I / 480P / 576P 
1080i (60 / 59.94 / 50) 
720p (60 / 59.94 / 50) 
HDMI 
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98) 
General 
Working voltage 
DC12V, or Battery 6.5V-17V 
DT-X71F 
≤ 
15W 
Power consumption 8W 
DT-X71H 
≤ 
DT-X71C 
≤ 
7W 
Working temperature 0 
+40 
℃ 
℃~ 
Working humidity 10% 
90% 
~ 
Storage temperature -15 
+60 
℃ 
℃~ 
Storage humidity 10% 
90% 
~ 
Dimensions 
192 
× 
139 
× 
47mm 
Net weight 550g 
* DT-X71C doesn’t support SDI input; 
** Only DT-X71H support SMPTE-425M format. 
11. Packing List 
1. Monitor 
1 
× 
2. User Manual 
1 
× 
3. Power adaptor 
1 
× 
4. Power cable 
1 
× 
5. Sun hood 
1 
× 
6. Screw ball head 
1 
× 
7. LCD protection film 
1 
×
This model is manufactured, warranted and supported by SWIT Electronics Co., Ltd. / SWIT Electronics USA, LLC, 
and distributed in North America by JVC Professional Video Products. 
To obtain service or for further information, please contact: 
SWIT Electronics USA, LLC. 
Address: 4300 Stevens Creek Blvd., Suite 230, San Jose, CA 95129 
Toll free: 1 866 986-SWIT (7948) • Tel: 408 260-8258 
· 
Fax: 408 228-8438 
Email: info@swit.us • Website: www.swit.us 
Version: 120807

More Related Content

What's hot

Sony LMD-4251TD
Sony LMD-4251TDSony LMD-4251TD
Sony LMD-4251TD
AV ProfShop
 
NEC X554 un 2
NEC X554 un 2NEC X554 un 2
NEC X554 un 2
SchoolVision Inc.
 
Sony LMD-4250W
Sony LMD-4250WSony LMD-4250W
Sony LMD-4250W
AV ProfShop
 
ELO ET 2494L
ELO ET 2494LELO ET 2494L
ELO ET 2494L
ScanSource Brasil
 
Sony LMD-1530W
Sony LMD-1530WSony LMD-1530W
Sony LMD-1530W
AV ProfShop
 
ELO ET 2293L e ET 2294L
ELO ET 2293L e ET 2294LELO ET 2293L e ET 2294L
ELO ET 2293L e ET 2294L
ScanSource Brasil
 
Sony LMD 1750W
Sony LMD 1750WSony LMD 1750W
Sony LMD 1750W
AV ProfShop
 
Specification Sheet for KPC-DNN100NHV15
Specification Sheet for KPC-DNN100NHV15Specification Sheet for KPC-DNN100NHV15
Specification Sheet for KPC-DNN100NHV15
KT&C America, Inc
 
AJA HDP2
AJA HDP2AJA HDP2
AJA HDP2
AV ProfShop
 
Panasonic AG-HMX100
Panasonic AG-HMX100Panasonic AG-HMX100
Panasonic AG-HMX100
AV ProfShop
 
AJA D10 CE
AJA D10 CEAJA D10 CE
AJA D10 CE
AV ProfShop
 
ELO ET 4202L
ELO ET 4202LELO ET 4202L
ELO ET 4202L
ScanSource Brasil
 

What's hot (12)

Sony LMD-4251TD
Sony LMD-4251TDSony LMD-4251TD
Sony LMD-4251TD
 
NEC X554 un 2
NEC X554 un 2NEC X554 un 2
NEC X554 un 2
 
Sony LMD-4250W
Sony LMD-4250WSony LMD-4250W
Sony LMD-4250W
 
ELO ET 2494L
ELO ET 2494LELO ET 2494L
ELO ET 2494L
 
Sony LMD-1530W
Sony LMD-1530WSony LMD-1530W
Sony LMD-1530W
 
ELO ET 2293L e ET 2294L
ELO ET 2293L e ET 2294LELO ET 2293L e ET 2294L
ELO ET 2293L e ET 2294L
 
Sony LMD 1750W
Sony LMD 1750WSony LMD 1750W
Sony LMD 1750W
 
Specification Sheet for KPC-DNN100NHV15
Specification Sheet for KPC-DNN100NHV15Specification Sheet for KPC-DNN100NHV15
Specification Sheet for KPC-DNN100NHV15
 
AJA HDP2
AJA HDP2AJA HDP2
AJA HDP2
 
Panasonic AG-HMX100
Panasonic AG-HMX100Panasonic AG-HMX100
Panasonic AG-HMX100
 
AJA D10 CE
AJA D10 CEAJA D10 CE
AJA D10 CE
 
ELO ET 4202L
ELO ET 4202LELO ET 4202L
ELO ET 4202L
 

Viewers also liked

Datavideo RMC-190 PTZ camara control unit
Datavideo RMC-190 PTZ camara control unitDatavideo RMC-190 PTZ camara control unit
Datavideo RMC-190 PTZ camara control unit
AV ProfShop
 
Datavideo DN-600 HArd Drive Recorder with removable hard drive
Datavideo DN-600 HArd Drive Recorder with removable hard driveDatavideo DN-600 HArd Drive Recorder with removable hard drive
Datavideo DN-600 HArd Drive Recorder with removable hard drive
AV ProfShop
 
Atomos Shogun Brochure
Atomos Shogun BrochureAtomos Shogun Brochure
Atomos Shogun Brochure
AV ProfShop
 
Datavideo TLM-170H 17" Widescreen LCD Monitor - Desktop Version
Datavideo TLM-170H 17" Widescreen LCD Monitor - Desktop VersionDatavideo TLM-170H 17" Widescreen LCD Monitor - Desktop Version
Datavideo TLM-170H 17" Widescreen LCD Monitor - Desktop Version
AV ProfShop
 
Sennheiser SKP 100 G3 plug on transmitter
Sennheiser SKP 100 G3 plug on transmitterSennheiser SKP 100 G3 plug on transmitter
Sennheiser SKP 100 G3 plug on transmitter
AV ProfShop
 
GoPro Hero 3 White Edition
GoPro Hero 3 White EditionGoPro Hero 3 White Edition
GoPro Hero 3 White Edition
AV ProfShop
 
Sony VPL-DX Series Projectors
Sony VPL-DX Series ProjectorsSony VPL-DX Series Projectors
Sony VPL-DX Series Projectors
AV ProfShop
 
Senheiser EW-145-G3 Wireless kit
Senheiser EW-145-G3 Wireless kitSenheiser EW-145-G3 Wireless kit
Senheiser EW-145-G3 Wireless kit
AV ProfShop
 
Datavideo PD-3 Power Distribution Center
Datavideo PD-3 Power Distribution CenterDatavideo PD-3 Power Distribution Center
Datavideo PD-3 Power Distribution Center
AV ProfShop
 
Sony NEX FS700R Brochure
Sony NEX FS700R BrochureSony NEX FS700R Brochure
Sony NEX FS700R Brochure
AV ProfShop
 
Gy hm850890 brochure2
Gy hm850890 brochure2Gy hm850890 brochure2
Gy hm850890 brochure2
AV ProfShop
 
ASL Intercom PS-19AM 1-channel beltpacks wth program (AUX) input
ASL Intercom PS-19AM 1-channel beltpacks wth program (AUX) inputASL Intercom PS-19AM 1-channel beltpacks wth program (AUX) input
ASL Intercom PS-19AM 1-channel beltpacks wth program (AUX) input
AV ProfShop
 
JVC Gy hm850brochure
JVC Gy hm850brochureJVC Gy hm850brochure
JVC Gy hm850brochure
AV ProfShop
 
Roland V-800HD Switcher
Roland V-800HD SwitcherRoland V-800HD Switcher
Roland V-800HD Switcher
AV ProfShop
 
Datavideo SE-500 4 Channel Analogue Micer / Switcher
Datavideo SE-500 4 Channel Analogue Micer / SwitcherDatavideo SE-500 4 Channel Analogue Micer / Switcher
Datavideo SE-500 4 Channel Analogue Micer / Switcher
AV ProfShop
 
Blackmagic Design Cinema Camera user manual
Blackmagic Design Cinema Camera user manualBlackmagic Design Cinema Camera user manual
Blackmagic Design Cinema Camera user manual
AV ProfShop
 

Viewers also liked (17)

Datavideo RMC-190 PTZ camara control unit
Datavideo RMC-190 PTZ camara control unitDatavideo RMC-190 PTZ camara control unit
Datavideo RMC-190 PTZ camara control unit
 
Hdr as15
Hdr as15Hdr as15
Hdr as15
 
Datavideo DN-600 HArd Drive Recorder with removable hard drive
Datavideo DN-600 HArd Drive Recorder with removable hard driveDatavideo DN-600 HArd Drive Recorder with removable hard drive
Datavideo DN-600 HArd Drive Recorder with removable hard drive
 
Atomos Shogun Brochure
Atomos Shogun BrochureAtomos Shogun Brochure
Atomos Shogun Brochure
 
Datavideo TLM-170H 17" Widescreen LCD Monitor - Desktop Version
Datavideo TLM-170H 17" Widescreen LCD Monitor - Desktop VersionDatavideo TLM-170H 17" Widescreen LCD Monitor - Desktop Version
Datavideo TLM-170H 17" Widescreen LCD Monitor - Desktop Version
 
Sennheiser SKP 100 G3 plug on transmitter
Sennheiser SKP 100 G3 plug on transmitterSennheiser SKP 100 G3 plug on transmitter
Sennheiser SKP 100 G3 plug on transmitter
 
GoPro Hero 3 White Edition
GoPro Hero 3 White EditionGoPro Hero 3 White Edition
GoPro Hero 3 White Edition
 
Sony VPL-DX Series Projectors
Sony VPL-DX Series ProjectorsSony VPL-DX Series Projectors
Sony VPL-DX Series Projectors
 
Senheiser EW-145-G3 Wireless kit
Senheiser EW-145-G3 Wireless kitSenheiser EW-145-G3 Wireless kit
Senheiser EW-145-G3 Wireless kit
 
Datavideo PD-3 Power Distribution Center
Datavideo PD-3 Power Distribution CenterDatavideo PD-3 Power Distribution Center
Datavideo PD-3 Power Distribution Center
 
Sony NEX FS700R Brochure
Sony NEX FS700R BrochureSony NEX FS700R Brochure
Sony NEX FS700R Brochure
 
Gy hm850890 brochure2
Gy hm850890 brochure2Gy hm850890 brochure2
Gy hm850890 brochure2
 
ASL Intercom PS-19AM 1-channel beltpacks wth program (AUX) input
ASL Intercom PS-19AM 1-channel beltpacks wth program (AUX) inputASL Intercom PS-19AM 1-channel beltpacks wth program (AUX) input
ASL Intercom PS-19AM 1-channel beltpacks wth program (AUX) input
 
JVC Gy hm850brochure
JVC Gy hm850brochureJVC Gy hm850brochure
JVC Gy hm850brochure
 
Roland V-800HD Switcher
Roland V-800HD SwitcherRoland V-800HD Switcher
Roland V-800HD Switcher
 
Datavideo SE-500 4 Channel Analogue Micer / Switcher
Datavideo SE-500 4 Channel Analogue Micer / SwitcherDatavideo SE-500 4 Channel Analogue Micer / Switcher
Datavideo SE-500 4 Channel Analogue Micer / Switcher
 
Blackmagic Design Cinema Camera user manual
Blackmagic Design Cinema Camera user manualBlackmagic Design Cinema Camera user manual
Blackmagic Design Cinema Camera user manual
 

Similar to JVC DT-E17L4G Full HD LCD 17" Studio Monitor

samsung_t220_t220g_t200_t200g_training.pdf
samsung_t220_t220g_t200_t200g_training.pdfsamsung_t220_t220g_t200_t200g_training.pdf
samsung_t220_t220g_t200_t200g_training.pdf
JoseAlfredoMuoz2
 
2010 Newest One Tech Product Leaflets
2010 Newest One Tech Product Leaflets2010 Newest One Tech Product Leaflets
2010 Newest One Tech Product Leaflets
newestonetech
 
Save professional lilliput 7 665 o 665 gl 70np ho y color tft lcd monitor ...
Save professional lilliput 7 665  o 665 gl 70np  ho  y color tft lcd monitor ...Save professional lilliput 7 665  o 665 gl 70np  ho  y color tft lcd monitor ...
Save professional lilliput 7 665 o 665 gl 70np ho y color tft lcd monitor ...
comeon studio
 
Sony LMD 4251TD
Sony LMD 4251TDSony LMD 4251TD
Sony LMD 4251TD
AV ProfShop
 
Dukane image pro 9008 hd
Dukane image pro 9008 hdDukane image pro 9008 hd
Dukane image pro 9008 hd
SchoolVision Inc.
 
43pp8545 69 dfu_eng
43pp8545 69 dfu_eng43pp8545 69 dfu_eng
43pp8545 69 dfu_eng
Malik Arif
 
Dukane Imagepro 8107 wib
Dukane Imagepro 8107 wibDukane Imagepro 8107 wib
Dukane Imagepro 8107 wib
DukaneAVMarketing
 
84 inch Large Format Professional Monitor
84 inch Large Format Professional Monitor84 inch Large Format Professional Monitor
84 inch Large Format Professional Monitor
Chris Bartram, Digital Displays Specialist
 
ELO ET 2794L
ELO ET 2794LELO ET 2794L
ELO ET 2794L
ScanSource Brasil
 
Sony LMD 2451TD
Sony LMD 2451TDSony LMD 2451TD
Sony LMD 2451TD
AV ProfShop
 
Hxrmc1accbroch
Hxrmc1accbrochHxrmc1accbroch
Hxrmc1accbroch
AV ProfShop
 
ELO ET 3243L
ELO ET 3243LELO ET 3243L
ELO ET 3243L
ScanSource Brasil
 
CDS Battery Shelf Edge Display
CDS Battery Shelf Edge Display CDS Battery Shelf Edge Display
CDS Battery Shelf Edge Display
Chris Bartram, Digital Displays Specialist
 
AJA RH10UC
AJA RH10UCAJA RH10UC
AJA RH10UC
AV ProfShop
 
Digital Watchdog DWC-D4363TIRB User Manual
Digital Watchdog DWC-D4363TIRB User ManualDigital Watchdog DWC-D4363TIRB User Manual
Digital Watchdog DWC-D4363TIRB User Manual
JMAC Supply
 
Digital Watchdog DWC-C261T User Manual
Digital Watchdog DWC-C261T User ManualDigital Watchdog DWC-C261T User Manual
Digital Watchdog DWC-C261T User Manual
JMAC Supply
 
Dukane Imagepro 9010
Dukane Imagepro 9010Dukane Imagepro 9010
Dukane Imagepro 9010
SchoolVision Inc.
 
ELO ET 1790L
ELO ET 1790LELO ET 1790L
ELO ET 1790L
ScanSource Brasil
 
LED HD VIDEO PROCESSOR USER’S MANUAL
LED HD VIDEO PROCESSOR USER’S MANUALLED HD VIDEO PROCESSOR USER’S MANUAL
LED HD VIDEO PROCESSOR USER’S MANUAL
Max Dan
 
HXR-MC2000E
HXR-MC2000EHXR-MC2000E
HXR-MC2000E
AVNed
 

Similar to JVC DT-E17L4G Full HD LCD 17" Studio Monitor (20)

samsung_t220_t220g_t200_t200g_training.pdf
samsung_t220_t220g_t200_t200g_training.pdfsamsung_t220_t220g_t200_t200g_training.pdf
samsung_t220_t220g_t200_t200g_training.pdf
 
2010 Newest One Tech Product Leaflets
2010 Newest One Tech Product Leaflets2010 Newest One Tech Product Leaflets
2010 Newest One Tech Product Leaflets
 
Save professional lilliput 7 665 o 665 gl 70np ho y color tft lcd monitor ...
Save professional lilliput 7 665  o 665 gl 70np  ho  y color tft lcd monitor ...Save professional lilliput 7 665  o 665 gl 70np  ho  y color tft lcd monitor ...
Save professional lilliput 7 665 o 665 gl 70np ho y color tft lcd monitor ...
 
Sony LMD 4251TD
Sony LMD 4251TDSony LMD 4251TD
Sony LMD 4251TD
 
Dukane image pro 9008 hd
Dukane image pro 9008 hdDukane image pro 9008 hd
Dukane image pro 9008 hd
 
43pp8545 69 dfu_eng
43pp8545 69 dfu_eng43pp8545 69 dfu_eng
43pp8545 69 dfu_eng
 
Dukane Imagepro 8107 wib
Dukane Imagepro 8107 wibDukane Imagepro 8107 wib
Dukane Imagepro 8107 wib
 
84 inch Large Format Professional Monitor
84 inch Large Format Professional Monitor84 inch Large Format Professional Monitor
84 inch Large Format Professional Monitor
 
ELO ET 2794L
ELO ET 2794LELO ET 2794L
ELO ET 2794L
 
Sony LMD 2451TD
Sony LMD 2451TDSony LMD 2451TD
Sony LMD 2451TD
 
Hxrmc1accbroch
Hxrmc1accbrochHxrmc1accbroch
Hxrmc1accbroch
 
ELO ET 3243L
ELO ET 3243LELO ET 3243L
ELO ET 3243L
 
CDS Battery Shelf Edge Display
CDS Battery Shelf Edge Display CDS Battery Shelf Edge Display
CDS Battery Shelf Edge Display
 
AJA RH10UC
AJA RH10UCAJA RH10UC
AJA RH10UC
 
Digital Watchdog DWC-D4363TIRB User Manual
Digital Watchdog DWC-D4363TIRB User ManualDigital Watchdog DWC-D4363TIRB User Manual
Digital Watchdog DWC-D4363TIRB User Manual
 
Digital Watchdog DWC-C261T User Manual
Digital Watchdog DWC-C261T User ManualDigital Watchdog DWC-C261T User Manual
Digital Watchdog DWC-C261T User Manual
 
Dukane Imagepro 9010
Dukane Imagepro 9010Dukane Imagepro 9010
Dukane Imagepro 9010
 
ELO ET 1790L
ELO ET 1790LELO ET 1790L
ELO ET 1790L
 
LED HD VIDEO PROCESSOR USER’S MANUAL
LED HD VIDEO PROCESSOR USER’S MANUALLED HD VIDEO PROCESSOR USER’S MANUAL
LED HD VIDEO PROCESSOR USER’S MANUAL
 
HXR-MC2000E
HXR-MC2000EHXR-MC2000E
HXR-MC2000E
 

More from AV ProfShop

Decimator MD-HX hardware-manual_fv1.3
Decimator MD-HX hardware-manual_fv1.3Decimator MD-HX hardware-manual_fv1.3
Decimator MD-HX hardware-manual_fv1.3
AV ProfShop
 
Panasonic AV-HS410 Multiformat Vision Mixer HD/SD
Panasonic AV-HS410 Multiformat Vision Mixer HD/SDPanasonic AV-HS410 Multiformat Vision Mixer HD/SD
Panasonic AV-HS410 Multiformat Vision Mixer HD/SD
AV ProfShop
 
Panasonic AW-HE40SW/SK/HW/HK PTZ Camera with HD-SDI / HDMI Output
Panasonic AW-HE40SW/SK/HW/HK PTZ Camera with HD-SDI / HDMI OutputPanasonic AW-HE40SW/SK/HW/HK PTZ Camera with HD-SDI / HDMI Output
Panasonic AW-HE40SW/SK/HW/HK PTZ Camera with HD-SDI / HDMI Output
AV ProfShop
 
Sony MCX-500 Live Production Switcher
Sony MCX-500 Live Production SwitcherSony MCX-500 Live Production Switcher
Sony MCX-500 Live Production Switcher
AV ProfShop
 
JVC GY-HM200 GY-HM170 Brochure AVProfShop
JVC GY-HM200 GY-HM170 Brochure AVProfShopJVC GY-HM200 GY-HM170 Brochure AVProfShop
JVC GY-HM200 GY-HM170 Brochure AVProfShop
AV ProfShop
 
JVC GY-HM620 Brochure AVProfShop
JVC GY-HM620 Brochure AVProfShopJVC GY-HM620 Brochure AVProfShop
JVC GY-HM620 Brochure AVProfShop
AV ProfShop
 
JVC GY-HM660 Brochure AVProfShop
JVC GY-HM660 Brochure AVProfShopJVC GY-HM660 Brochure AVProfShop
JVC GY-HM660 Brochure AVProfShop
AV ProfShop
 
Datavideo TP Kit (Teleprompter) Brochure
Datavideo TP Kit (Teleprompter) BrochureDatavideo TP Kit (Teleprompter) Brochure
Datavideo TP Kit (Teleprompter) Brochure
AV ProfShop
 
Datavideo MS-2800 Brochure
Datavideo MS-2800 BrochureDatavideo MS-2800 Brochure
Datavideo MS-2800 Brochure
AV ProfShop
 
Datavideo HS-2800 Brochure
Datavideo HS-2800 BrochureDatavideo HS-2800 Brochure
Datavideo HS-2800 Brochure
AV ProfShop
 
Datavideo CG-350 Brochure
Datavideo CG-350 BrochureDatavideo CG-350 Brochure
Datavideo CG-350 Brochure
AV ProfShop
 
Datavideo DVK-200 Brochure
Datavideo DVK-200 BrochureDatavideo DVK-200 Brochure
Datavideo DVK-200 Brochure
AV ProfShop
 
Datavideo ITC-100 Brochure
Datavideo ITC-100 BrochureDatavideo ITC-100 Brochure
Datavideo ITC-100 Brochure
AV ProfShop
 
Datavideo RMC-180 Brochure
Datavideo RMC-180 BrochureDatavideo RMC-180 Brochure
Datavideo RMC-180 Brochure
AV ProfShop
 
Datavideo HS-600 Hand Carry System Brochure
Datavideo HS-600 Hand Carry System BrochureDatavideo HS-600 Hand Carry System Brochure
Datavideo HS-600 Hand Carry System Brochure
AV ProfShop
 
Datavideo SE-600 Brochure
Datavideo SE-600 BrochureDatavideo SE-600 Brochure
Datavideo SE-600 Brochure
AV ProfShop
 
Datavideo SE-500 Brochure
Datavideo SE-500 BrochureDatavideo SE-500 Brochure
Datavideo SE-500 Brochure
AV ProfShop
 
Atomos Range Brochure
Atomos Range BrochureAtomos Range Brochure
Atomos Range Brochure
AV ProfShop
 
Sony PXW-Z450
Sony PXW-Z450Sony PXW-Z450
Sony PXW-Z450
AV ProfShop
 
Datavideo SE-2200 6 input HD broadcast quality switcher
Datavideo SE-2200 6 input HD broadcast quality switcherDatavideo SE-2200 6 input HD broadcast quality switcher
Datavideo SE-2200 6 input HD broadcast quality switcher
AV ProfShop
 

More from AV ProfShop (20)

Decimator MD-HX hardware-manual_fv1.3
Decimator MD-HX hardware-manual_fv1.3Decimator MD-HX hardware-manual_fv1.3
Decimator MD-HX hardware-manual_fv1.3
 
Panasonic AV-HS410 Multiformat Vision Mixer HD/SD
Panasonic AV-HS410 Multiformat Vision Mixer HD/SDPanasonic AV-HS410 Multiformat Vision Mixer HD/SD
Panasonic AV-HS410 Multiformat Vision Mixer HD/SD
 
Panasonic AW-HE40SW/SK/HW/HK PTZ Camera with HD-SDI / HDMI Output
Panasonic AW-HE40SW/SK/HW/HK PTZ Camera with HD-SDI / HDMI OutputPanasonic AW-HE40SW/SK/HW/HK PTZ Camera with HD-SDI / HDMI Output
Panasonic AW-HE40SW/SK/HW/HK PTZ Camera with HD-SDI / HDMI Output
 
Sony MCX-500 Live Production Switcher
Sony MCX-500 Live Production SwitcherSony MCX-500 Live Production Switcher
Sony MCX-500 Live Production Switcher
 
JVC GY-HM200 GY-HM170 Brochure AVProfShop
JVC GY-HM200 GY-HM170 Brochure AVProfShopJVC GY-HM200 GY-HM170 Brochure AVProfShop
JVC GY-HM200 GY-HM170 Brochure AVProfShop
 
JVC GY-HM620 Brochure AVProfShop
JVC GY-HM620 Brochure AVProfShopJVC GY-HM620 Brochure AVProfShop
JVC GY-HM620 Brochure AVProfShop
 
JVC GY-HM660 Brochure AVProfShop
JVC GY-HM660 Brochure AVProfShopJVC GY-HM660 Brochure AVProfShop
JVC GY-HM660 Brochure AVProfShop
 
Datavideo TP Kit (Teleprompter) Brochure
Datavideo TP Kit (Teleprompter) BrochureDatavideo TP Kit (Teleprompter) Brochure
Datavideo TP Kit (Teleprompter) Brochure
 
Datavideo MS-2800 Brochure
Datavideo MS-2800 BrochureDatavideo MS-2800 Brochure
Datavideo MS-2800 Brochure
 
Datavideo HS-2800 Brochure
Datavideo HS-2800 BrochureDatavideo HS-2800 Brochure
Datavideo HS-2800 Brochure
 
Datavideo CG-350 Brochure
Datavideo CG-350 BrochureDatavideo CG-350 Brochure
Datavideo CG-350 Brochure
 
Datavideo DVK-200 Brochure
Datavideo DVK-200 BrochureDatavideo DVK-200 Brochure
Datavideo DVK-200 Brochure
 
Datavideo ITC-100 Brochure
Datavideo ITC-100 BrochureDatavideo ITC-100 Brochure
Datavideo ITC-100 Brochure
 
Datavideo RMC-180 Brochure
Datavideo RMC-180 BrochureDatavideo RMC-180 Brochure
Datavideo RMC-180 Brochure
 
Datavideo HS-600 Hand Carry System Brochure
Datavideo HS-600 Hand Carry System BrochureDatavideo HS-600 Hand Carry System Brochure
Datavideo HS-600 Hand Carry System Brochure
 
Datavideo SE-600 Brochure
Datavideo SE-600 BrochureDatavideo SE-600 Brochure
Datavideo SE-600 Brochure
 
Datavideo SE-500 Brochure
Datavideo SE-500 BrochureDatavideo SE-500 Brochure
Datavideo SE-500 Brochure
 
Atomos Range Brochure
Atomos Range BrochureAtomos Range Brochure
Atomos Range Brochure
 
Sony PXW-Z450
Sony PXW-Z450Sony PXW-Z450
Sony PXW-Z450
 
Datavideo SE-2200 6 input HD broadcast quality switcher
Datavideo SE-2200 6 input HD broadcast quality switcherDatavideo SE-2200 6 input HD broadcast quality switcher
Datavideo SE-2200 6 input HD broadcast quality switcher
 

JVC DT-E17L4G Full HD LCD 17" Studio Monitor

  • 1. 7" Portable On-camera LCD Monitor User Manual Model: DT-X71F HDSDI&HDMI, Waveform, Audio meter, Focus assist DT-X71H 3GSDI&HDMI DT-X71C HDMI Please read this User Manual throughout before using.
  • 2. Preface Congratulations on your purchase of this product. Please read this user manual carefully. 1 . All internal technologies of this product are protected, including device, software and trademark. Reproduction in whole or in part without written permission is prohibited. 2 . All brands and trademarks are protected and other relative trademarks in this user manual are the properties of their respective owners. 3 . Due to constant effort of product development, SWIT Electronics reserves the right to make changes and improvements to the product described in this manual without prior notice. 4 . The warranty period of this product is 2 years, and does not cover the following: (1) Physical damage to the surface of the products, including scratches, cracks or other damage to the LCD screen or other externally exposed parts; (2) Misuse, abuse or negligent operation to the product; (3) The product is disassembled by anyone other than an authorized service center. It is considered normal that the LCD bright dot defects are not to exceed three. 5 . For any suggestions and requirements on this product, please contact us through phone, fax, Email, etc. SWIT Electronics Co., Ltd. / SWIT Electronics USA, LLC. Address: 4300 Stevens Creek Blvd. Suite 230 San Jose, CA 95129 Toll free: 1 866 986-SWIT(7948) Tel: 408 260-8258 Fax: 408 228-8438 Email: info@swit.us Website: www.swit.us
  • 3. Maintenance Monitor 1. Please keep the signal terminals and the cooling vent away from knife-edge, metal or liquid in order to avoid short-circuit and damage. 2. Please don't try to disassemble any parts of the monitor by yourself, which would probably damage the monitor and do harm to human body, and it will cause the invalidation of product warranty. 3. Please don't touch the screen with your fingers, which would probably deface the screen. 4. Please don't press the screen; the LCD is extremely exquisite and flimsy. The power Please use the provided power adapter or the battery recommended by the manufacturer in order to avoid damage. For a third party power adapter, please make sure the voltage range, supplied power, and polarity of power lead are fit. Please disconnect the power cable or take off the battery under the following situations: 1. If you do not operate this monitor for a period of time; 2. If the power cable or power adaptor is damaged; 3. If the monitor housing is broken. Working Environment 1. Please don't lay this product on the unstable place. 2. Please don't lay this product in hot, cold or wet location. Cleaning 1. Please clean the screen with dry and downy cloth or special LCD cleanser. 2. Please do not press hard when cleaning the screen. 3. Please do not use water or other chemical cleanser to clean the screen. The chemical may damage the LCD. 4. For first time use, please tear off the factory LCD film. To protect the LCD screen, please post the LCD protection film offered in the package.
  • 4. 1. Features DT-X71F New high resolution 7” LCD Panel 16:9, 1024×600, 16.77 million colors, 900:1 contrast, and H160 ° ◆ / V160 ° viewing angle. Multiple inputs 2 HD/SD-SDI, 1 HDMI and 1 Composite input. ◆ ◆ Loop through outputs Each of the 2 input HD/SD-SDI has loop through output. ◆ HDMI converted to SDI output Supported HDMI formats: 480i / 576i / 720p (50, 59.94, 60) / 1080i (50, 59.94, 60) / 1080P (23.98 24, 25, 29.97, 30), and the output SDI will embed the audio (48KHz) from HDMI. ◆ Waveform (Y, Cb, Cr, R, G, B) and full scale There are totally 6 kinds of waveform display, available under both SDI and HDMI, to check the Luminance (Y), Blue-difference (Cb), Red-difference (Cr), Red (R), Green (G), Blue (B), and the Y, Cb, Cr can be simultaneously displayed, R, G, B can be simultaneously displayed, and each of the waveforms can be set to full scale display. ◆ Vector scope The displayed vector scope pattern is available under both SDI and HDMI, represents saturation as distance from the center of the circle, and hue as the angle, in standard position, around it. ◆ Histogram (R, G, B) The histogram is a bar graph that shows the distribution of luminance values in the picture. There’re R, G, B histograms that individually displayed simultaneously, available under both SDI and HDMI. ◆ 16-ch audio meter Under HDSDI, it displays 16 channels audio bars, with mark, and under SDSDI or HDMI, it displays 2 channels audio bars with mark. The audio bar is green, and will turn yellow when audio exceeds -20dB, and turn red when exceeds -10dB. SDI timecode ◆ Under SDI input, it can display the SMPTE timecode, which is used extensively for synchronization, and for logging and identifying material in recorded media. Peaking focus assist (red/blue switch) ◆ The Peaking focus assist function is to mark the sharpest edges of the image with red or blue color, for users to check if the subjects are focused. ◆ Zebra stripes Zebra Stripes are used to check if the image is over exposed or not by showing black and white lines on the monitor. It is considered over exposed when luminance value exceeds 90%. ◆ False color The false color is used to aid in the setting of camera exposure. Under false color mode, there’s a false color key on the bottom of screen for reference. The over exposed subjects (above 101 IRE) on the monitor will display as RED, and the underexposed subjects will display as BLUE. For correct exposed subjects, it will display as green and pink. ◆ Blue Only Under the Blue Only Mode, only the blue pixels are used to generate the image, because hue and saturation can be adjusted quicker and more accurately. ◆ DSLR scale zoom in The Canon DSLR outputs the CMOS sensor ratio HDMI and this zoom in mode can make the effective image scale full screen on the monitor. ◆ User definable function keys There are 3 function keys on the monitor front panel, that permit users to define shortcuts for the various functions. ◆ User editable video title User can edit a video title for the current camera, and the title will display on the top of screen. ◆ Front and Rear 3-color TALLY light 2 TALLY lights design, to give “live” signals to people in front of the camera, as well as the camera operator behind. Image Flip ◆ Set image to rotate by 180 . °
  • 5. DT-X71H High resolution 7” LCD Panel 16:9, 1024×600, 16.77 million colors, 900:1 contrast, and H160 ° ◆ / V160 ° viewing angle. 3Gbps SDI support Accepts 3G/HD/SD-SDI input. ◆ ◆ Multiple inputs 1 3G/HD/SD-SDI, 1 HDMI, 1 Composite input and L/R stereo audio. ◆ Loop through outputs 1 3G/HD/SD-SDI, 1 HDMI and 1 Composite video loop through output. ◆ SDI embedded audio output The SDI embedded audio can be output through 3.5mm earphone on the front panel. Image Flip. ◆ Set image to rotate by 180 ° DSLR scale zoom in ◆ The Canon DSLR outputs the CMOS sensor ratio HDMI and this zoom in mode can make the effective image scale full screen on the monitor. ◆ User definable function keys There are 2 function keys on the monitor front panel, that permit users to define shortcuts for the various functions. ◆ User editable video title User can edit a video title for the current camera, and the title will display on the top of screen. Front and Rear 3-color TALLY light ◆ 2 TALLY lights design, to give “live” signals to people in front of the camera, as well as the camera operator behind. DT-X71C New high resolution 7” LCD Panel 16:9, 1024×600, 16.77 million colors, 900:1 contrast, and H160 ° ◆ / V160 ° viewing angle. Multiple inputs 1 HDMI, 1 Composite input and L/R stereo audio input. ◆ ◆ Loop through outputs 1 HDMI and 1 Composite loop through output. ◆ DSLR scale zoom in The Canon DSLR outputs the CMOS sensor ratio HDMI and this zoom in mode can make the effective image scale full screen on the monitor. Image Flip ◆ Set image to rotate by 180 . ° User definable function keys ◆ There are 2 function keys on the monitor front panel, that permit users to define shortcuts for the various functions. ◆ User editable video title User can edit a video title for the current camera, and the title will display on the top of screen. Front and Rear 3-color TALLY light ◆ 2 TALLY lights design, to give “live” signals to people in front of the camera, as well as the camera operator behind.
  • 6. 2. Panel Instruction DT-X71F Front view PHONE: Earphone jack ⑵ ⑴ POWER: Power on/off Connect with power cable or mount battery, press the “POWER” and the power indicator is turned on and after 10 seconds, the monitor will be switched on and get into normal working status. Press the “POWER” again, the indicator is turned off and monitor is switched off. Disconnect with power cable or take off the battery if the monitor will not be used for a period of time. IN: Input signal selection ⑶ Press “IN” and revolve the “OK” to select the input video signal. ⑷ F1: User definable function key 1 FOCUS: Peaking Focus Assist ⑸ Press “FOCUS” once, it will display the current peaking on/off status. Press “FOCUS” again to switch on RED line focus assist, switch on BLUE line focus assist, and switch off in turn. F.COLOR: False color ⑹ Press “F.COLOR” once, it will display the current false color on/off status. Press “F.COLOR” again to switch on/off the false color mode. DISPLAY: Display current settings ⑺ Press “Display” to display safety mark, title and the current input signal information ⑻ F2: User definable function key 2 ⑼ F3: User definable function key 3 WAVEFORM: Display waveform ⑽ Press “WAVEFORM” once, it will display the waveform menu as: Revolve “OK” to select a waveform display mode and turn it on. The selected waveform will display on the screen. ⑾ VECTOR: Display vector scope Press “VECTOR” to switched on/off the Vector scope ⑿ MENU: Press to enter Menu OK: Select and Apply ⒀ Under menu system, revolve “OK” to adjust settings and press to apply; and out of menu system, directly revolve “OK” to adjust volume. TALLY Light: Red, Green and Yellow 3-color TALLY indicator ⒁
  • 7. Rear view DC 12V IN: Connect with DC12V 4-pin XLR power adapter. ⑵ ⑴ TALLY Light: Red, Green and Yellow 3-color TALLY indicator Battery mount: ⑶ Connect with JVC battery BN-VF823 or SWIT battery BN-S8823 to power the monitor. ⑷ HDSDI IN1/2: HD/SD-SDI input (BNC connector) ⑸ HDSDI OUT: HDMI converted to SDI output (BNC connector) ⑹ HDSDI LOOP1/2: HD/SD-SDI loop through output (BNC connector) ⑺ VIDEO IN: Composite video input (BNC connector) ⑻ TALLY controlling port (RJ45): terminal description is as follows: The RED light is on when connecting the terminal “R” with “GND”, and goes out when disconnecting. The GREEN light is on when connecting the terminal “G” with “GND”, and goes out when disconnecting. The YELLOW light is on when connecting the terminal “Y” with “GND”, and goes out when disconnecting HDMI: HDMI input ⑼ Input formats Terminal 1 2 3 4 5 6 7 8 Description Y G GND R Input Supported formats CVBS PAL / NTSC 480I / 576I / 480P / 576P 1080i (60 / 59.94 / 50) 720p (60 / 59.94 / 50) HDMI 1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98) 1080i (60 / 59.94 / 50) SMPTE-274M 1080p (30 / 29.97 / 25 / 24 / 23.98) SMPTE-296M 720p (60 / 59.94 / 50) SMPTE-125M 480i (59.94) SDI ITU-R BT.656 576i (50)
  • 8. DT-X71H Front view PHONE: Earphone jack, for SDI embedded audio, HDMI audio and analog audio ⑵ ⑴ POWER: Power on/off Connect with power cable or mount battery, press the “POWER” and the power indicator is turned on and after 10 seconds, the monitor will be switched on and get into normal working status. Press the “POWER” again, the indicator is turned off and monitor is switched off. Remark: Disconnect with power cable or take off the battery if the monitor will not be used for a period of time. ⑶ CVBS: Press to switch the input signal to Composite video ⑷ HDMI: Press to switch the input signal to HDMI ⑸ SDI: Press to switch the input signal to SDI ⑹ OVERSCAN: Overscan / Underscan switch ⑺ MENU: Press to enter Menu ⑻ F1: User definable function key 1 ⑼ F2: User definable function key 2 ⑽ RATIO: 16:9 and 4:3 switch ZOOM: Picture Zoom-in ⑾ Press “ZOOM” to switch ZOOM1: Canon DSLR scale zoom-in, and ZOOM2: pixel to pixel zoom-in. DISPLAY: Display current settings ⑿ Press “Display” to display safety mark, title and the current input signal information OK: Select and Apply ⒀ Under menu system, revolve “OK” to adjust settings and press to apply; and out of menu system, directly revolve “OK” to adjust volume. TALLY Light: Red, Green and Yellow 3-color TALLY indicator ⒁
  • 9. Rear view DC 12V IN: Connect with DC12V 4-pin XLR power adapter. ⑵ ⑴ TALLY Light: Red, Green and Yellow 3-color TALLY indicator Battery mount: ⑶ Connect with JVC battery BN-VF823 or SWIT battery BN-S8823 to power the monitor. ⑷ CVBS IN: Composite video input (BNC connector) ⑸ SDI-LOOP: 3G/HD/SD-SDI loop through output (BNC connector) ⑹ SDI-IN: 3G/HD/SD-SDI input (BNC connector) ⑺ HDMI-LOOP: HDMI loop through output ⑻ HDMI-IN: HDMI input ⑼ TALLY controlling port (RS-232): terminal description is as follows: The RED light is on when connecting the terminal “R” with “GND”, and goes out when disconnecting. The GREEN light is on when connecting the terminal “G” with “GND”, and goes out when disconnecting. The YELLOW light is on when connecting the terminal “Y” with “GND”, and goes out when disconnecting. ⑽ AUDIO L: Stereo audio left channel input (RCA connector) ⑾ AUDIO R: Stereo audio right channel input (RCA connector) ⑿ CVBS-LOOP: Composite video loop through output (BNC connector) Input formats Terminal 1 2 3 4 5 6 7 8 9 Description Y G R GND GND GND Input Supported formats CVBS PAL / NTSC 480I / 576I / 480P / 576P 1080i (60 / 59.94 / 50) 720p (60 / 59.94 / 50) HDMI 1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98) SMPTE-425M 1080p (60 / 59.94 / 50) 1080i (60 / 59.94 / 50) SMPTE-274M 1080p (30 / 29.97 / 25 / 24 / 23.98) SMPTE-296M 720p (60 / 59.94 / 50) SMPTE-125M 480i (59.94) SDI ITU-R BT.656 576i (50)
  • 10. DT-X71C Front view PHONE: Earphone jack ⑵ ⑴ POWER: Power on/off Connect with power cable or mount battery, press the “POWER” and the power indicator is turned on and after 10 seconds, the monitor will be switched on and get into normal working status. Press the “POWER” again, the indicator is turned off and monitor is switched off. Remark: Disconnect with power cable or take off the battery if the monitor will not be used for a period of time. ⑶ VIDEO: Press to switch the input signal to Composite video ⑷ HDMI: Press to switch the input signal to HDMI ⑸ B/W: Black and White mode ⑹ OVERSCAN: Overscan / Underscan switch ⑺ MENU: Press to enter Menu ⑻ F1: User definable function key 1 ⑼ F2: User definable function key 2 ⑽ RATIO: 16:9 and 4:3 switch ZOOM: Picture Zoom-in ⑾ Press “ZOOM” to switch ZOOM1: Canon DSLR scale zoom-in, and ZOOM2: pixel to pixel zoom-in. DISPLAY: Display current settings ⑿ Press “Display” to display safety mark, title and the current input signal information ⒀ OK: Select and Apply Under menu system, revolve “OK” to adjust settings and press to apply; and out of menu system, directly revolve “OK” to adjust volume. TALLY Light: Red, Green and Yellow 3-color TALLY indicator ⒁
  • 11. Rear view DC 12V IN: Connect with DC12V 4-pin XLR power adapter. ⑵ ⑴ TALLY Light: Red, Green and Yellow 3-color TALLY indicator ⑶ Battery mount: Connect with JVC battery BN-VF823 or SWIT battery BN-S8823 to power the monitor. ⑷ CVBS IN: Composite video input (BNC connector) ⑸ HDMI-LOOP: HDMI loop through output ⑹ HDMI: HDMI input ⑺ TALLY controlling port (RS-232): terminal description is as follows: The RED light is on when connecting the terminal “R” with “GND”, and goes out when disconnecting. The GREEN light is on when connecting the terminal “G” with “GND”, and goes out when disconnecting. The YELLOW light is on when connecting the terminal “Y” with “GND”, and goes out when disconnecting ⑻ AUDIO L: Stereo audio L input (RCA connector) ⑼ AUDIO R: Stereo audio R input (RCA connector) ⑽ CVBS-LOOP: Composite video loop through output (BNC connector) Input formats Terminal 1 2 3 4 5 6 7 8 9 Description Y G R GND GND GND Input Supported formats CVBS PAL / NTSC 480I / 576I / 480P / 576P 1080i (60 / 59.94 / 50) 720p (60 / 59.94 / 50) HDMI 1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)
  • 12. 3. Menu Operation Press “MENU” and it will display menu system Revolve “OK” to select an item. The selected item will be highlighted display. Press “OK” to enter the selected item. Under menu system, press “MENU” to back to previous menu. The menu will automatically save and quit if it remains idle. 4. Picture Settings Submenu The Picture Settings Submenu includes: ⑴ CONTRAST: 0-100 value adjustment ⑵ BRIGHTNESS: 0-100 value adjustment ⑶ HUE: 0-100 value adjustment (Only available under Composite input) ⑷ SATURATION: 0-100 value adjustment ⑸ SHARPNESS: 0-100 value adjustment ⑹ PIC.MODE: User defined and preset picture modes: standard, soft and vivid selection 5. System Configuration Submenu The System Configuration Submenu includes: ⑴ RATIO: Select “16:9” or “4:3” to adjust the aspect ratio. ⑵ SCAN: “UNDERSCAN” / “OVERSCAN” selection ZOOM: “OFF”, “ZOOM1” and “ZOOM2” selection ⑶ ZOOM1: Canon DSLR scale zoom-in ZOOM2: Pixel to Pixel zoom-in ⑷ MARKER: Select and set the safety mark scale from 80%, 85%, 90% and 95%. FLIP: Select “YES” to flip the image by 180 . ⑸ ° ⑹ RESET: Revolve “OK” to RESET and press to recover all to factory setting.
  • 13. 6. OSD Settings Submenu The OSD Settings Submenu includes: ⑴ LANGUAGE: Menu language English / Chinese selection ⑵ H-POSITION: Menu horizontal position (0-100) adjustment, real-time preview, default value: 50, center. ⑶ V-POSITION: Menu vertical position (0-100) adjustment, real-time preview, default value: 50, center. DURATION: Menu timeout setting ⑷ Set a time (in seconds) in which the menu will automatically quit if remains idle. Default: 10 seconds; Range: 5 seconds to 60 seconds. 7. Title Settings Submenu Revolve OK button to select the letters, and press OK to input. Select SPACE to input space and DEL to delete the left letter. Max 10 letters are supported. After setting, press MENU, the system will save data to current user and quit menu. The menu will automatically save and quit if it remains idle. 8. Display Settings Submenu The DISPLAY settings submenu is to select the items to be displayed on screen when ‘DISPLAY” button is pressed. Revolve OK to turn on/off the items: (1) INFO: Including Input format, aspect ratio, underscan/overscan, zoom status (2) MARKER: Safety mark (3) TITLE: User edited title
  • 14. 9. FUNCTION KEY Settings Submenu The F KEY Settings Submenu is to define Function Keys on the front keyboard. The DT-X71F has 3 function keys: F1, F2 and F3; The DT-X71H and DT-X71C has 2 function keys: F1 and F2. The available function items of each model are: -------------------DT-X71F------------------- -------------------DT-X71H------------------- 01-RATIO: Aspect ratio switch 01-RATIO: Aspect ratio switch 02-SCAN: Underscan / Overscan switch 02-SCAN: Underscan / Overscan switch 03-ZOOM: Picture Zoom-in 03-ZOOM: Picture Zoom-in 04-PIC. MODE: Preset picture mode switch 04-B/W: Color / Black white switch 05-B/W: Color / Black white switch 05-FLIP: Image flip 06-BLUE ONLY: Blue only mode switch on/off 07-ZEBRA: Zebra over exposure switch on/off 08-VECTOR: Vector scope switch on/off 09-PATTERN: Internal colorbar switch on/off -------------------DT-X71C------------------- 10-RGB HIST: R, G, B Histogram switch on/off 01-RATIO: Aspect ratio switch 11-TIMECODE: SDI timecode display switch on/off 02-SCAN: Underscan / Overscan switch 12-F.COLOR: False color mode switch on/off 03-ZOOM: Picture Zoom-in 13-AUDIO BAR: Audio meter display switch on/off 04-B/W: Color / Black white switch 14-FOCUS: Peaking focus assist switch on/off, and 05-FLIP: Image flip red/blue selection 15-FLIP: Image flip
  • 15. 10. Specifications LCD Performance Size 7.0 inches Resolution 1024 RGB × × 600 Aspect ratio 16:9/4:3 Color system NTSC/PAL Brightness 400cd/m2 Contrast 900:1 Color 16.77 million colors Viewing angle H/V:160/160 Video Format SMPTE-425M ** 1080p (60 / 59.94 / 50) 1080i (60 / 59.94 / 50) SMPTE-274M 1080p (30 / 29.97 / 25 / 24 / 23.98) SMPTE-296M 720p (60 / 59.94 / 50) SMPTE-125M 480i (59.94) SDI * ITU-R BT.656 576i (50) 480I / 576I / 480P / 576P 1080i (60 / 59.94 / 50) 720p (60 / 59.94 / 50) HDMI 1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98) General Working voltage DC12V, or Battery 6.5V-17V DT-X71F ≤ 15W Power consumption 8W DT-X71H ≤ DT-X71C ≤ 7W Working temperature 0 +40 ℃ ℃~ Working humidity 10% 90% ~ Storage temperature -15 +60 ℃ ℃~ Storage humidity 10% 90% ~ Dimensions 192 × 139 × 47mm Net weight 550g * DT-X71C doesn’t support SDI input; ** Only DT-X71H support SMPTE-425M format. 11. Packing List 1. Monitor 1 × 2. User Manual 1 × 3. Power adaptor 1 × 4. Power cable 1 × 5. Sun hood 1 × 6. Screw ball head 1 × 7. LCD protection film 1 ×
  • 16. This model is manufactured, warranted and supported by SWIT Electronics Co., Ltd. / SWIT Electronics USA, LLC, and distributed in North America by JVC Professional Video Products. To obtain service or for further information, please contact: SWIT Electronics USA, LLC. Address: 4300 Stevens Creek Blvd., Suite 230, San Jose, CA 95129 Toll free: 1 866 986-SWIT (7948) • Tel: 408 260-8258 · Fax: 408 228-8438 Email: info@swit.us • Website: www.swit.us Version: 120807