The document describes a study that prepared carbon-supported PtRu nanocatalysts using an ethanol reduction method for different reaction times. The catalysts were characterized using various techniques and tested for their electrocatalytic activity in methanol oxidation. XRD and TEM analysis showed the catalysts had an FCC structure with an average particle size of 3.7 nm. Cyclic voltammetry tests found that the catalyst prepared at a 2h reduction time had higher electrocatalytic activity and stability for methanol electrooxidation compared to the other samples. The results suggest these catalysts could be promising anode catalysts for direct methanol fuel cells.
Electrooxidation of methanol on carbon supported pt ru nanocatalysts prepared...suresh899
Carbon Supported PtRu nanocatalysts have been prepared by simple impregnation reduction method in which Pt and Ru precursors are reduced by ethanol under reflux conditions for different reaction times. The prepared nanocatalysts were characterized by means of XRD, EDAX, ICP-AAS, FESEM and TEM. XRD analyses showed that all nanocatalysts exhibited f.c.c crystal structure, the structure characteristic for pure Pt, except for that reduced at prolonged reaction time of 4h which showed the presence of characteristic peak for Ru metal. The lattice constant calculations indicate that all catalysts are present in unalloyed phase and the average particle size as determined by TEM was in the range of 3.7 nm. The electrocatalytic activities and stability for the prepared nanocatalysts methanol electro-oxidation reaction (MOR) were studied by cyclic voltammetry. The catalysts prepared at 2h reduction time showed higher electrocatalytic activity in terms of mass specific activity and good stability over potential sweep for 100 cycles for methanol electro-oxidation. The results showed that the prepared nanocatalysts are considered as promising electrode catalyst (anode catalyst) for electro-oxidation of methanol in direct methanol fuel cells.
Parallel Reaction Kinetic Modelling Of Biogas To Biomethanol With Zno/Sio2 Na...IJERD Editor
Kinetic model proposed in this study is a single reaction kinetic model of parallel biogas into
biomethanol (CO2 + H2) and CO2 gas (CO + O2) in the gas phase. The phenomenon of this reaction is a new
breakthrough in the field of renewable energy and very exciting to be modeled kinetic. These parallel reactions
biomethanol and biogas into CO2 gas in this study utilizes content of methane (CH4) which is converted to CO2
by nanoprticles biomethanol and ZnO impregnated silica. Nanoparticles ZnO made with Zn (SO4) 7H2O and
NaOH with co precipitation method with stirring pressure of 1.2 bar and an isothermal drying temperature
180oC. Reaction biogas into biomethanol and CO2 takes place at a temperature of 350oC and a pressure of 1.2
bar produce biogas conversion into biomethanol 70% and 25% CO2 gas. at a temperature of 350oC and
volumetric rate of 5 ml per minute. Effect of water formed in this reaction will inhibit the formation of
biomethanol and hydrocarbons.
PEGylated magnetic nanoparticles (PEG@Fe3O4) as cost effectivealternative for...Pawan Kumar
An efficient, cost effective and environmental friendly PEGylated magnetic nanoparticle catalyzed oxida-tive cyanation via CH activation of tertiary amines to corresponding -aminonitriles using hydrogenperoxide as oxidant and sodium cyanide as cyanide source is described. The synthesized nanocatalyst waseasily recovered with the help of external magnet and was successfully reused for several runs withoutany significant loss in catalytic activity.
PEGylated magnetic nanoparticles (PEG@Fe3O4) as cost effectivealternative for...Pawan Kumar
tAn efficient, cost effective and environmental friendly PEGylated magnetic nanoparticle catalyzed oxida-tive cyanation via CH activation of tertiary amines to corresponding -aminonitriles using hydrogenperoxide as oxidant and sodium cyanide as cyanide source is described. The synthesized nanocatalyst waseasily recovered with the help of external magnet and was successfully reused for several runs withoutany significant loss in catalytic activity.
Effect of Solvent Swelling on the reactivity of demineralized Turkish LigniteIJERA Editor
In this research, effect of demineralization and solvent swelling on pyrolysis kinetics was investigated. The experiments were carried out to investigate theeffects of solvent swelling with different solvents, such as THF, Pyridine and DMSO after demineralization with HCl, HNO3 and HF successively. To calculate the activation energies of lignite sample during pyrolysis, TGA analyses were performed with raw and swollen samples at 5, 10 and 20° C/min heating rates. Coast-Redfernmodel was used for the determination of kinetic parameters. According to the results, the macromolecular structure of lignite was affected from these hydrogen bonding solvents. So, the activation energies of swollen samples found to be less than the raw lignite sample for all heating rates. The reactivity of lignite samples can be ordered as follows; DMSO swollen sample > Pyridine swollen sample> THF swollen sample. Activation energy of DMSO swollen lignite sample is 10.62 kJ/mole whereas activation energies of pyridine swollen and THF swollen sample are 17.83, 25.76 kJ/mol, respectively at a heating rate of 10° C/min. The results indicated that, solvent swelling has catalytic effect on pyrolysis kinetics.
A highly efficient, recyclable and magnetically separable core-shell structured CuZnO@Fe3O4 microsphere
wrapped with reduced graphene oxide (rGO@CuZnO@Fe3O4) photocatalyst has been developed and used
for the photoreduction of carbon dioxide with water to produce methanol under visible light irradiation.
Owing to the synergistic effect of the components and to the presence of a thin Fe2O3 layer on Fe3O4,
rGO@CuZnO@Fe3O4 4 exhibited higher catalytic activity as compared to the other possible combinations
such as CuZnO@Fe3O4 2 and GO@CuZnO@Fe3O4 3 microspheres. The yield of methanol in case of using
2 and 3 as photocatalyst was found to be 858 and 1749 mol g−1 cat, respectively. However, the yield
was increased to 2656 mol g−1 cat when rGO@CuZnO@Fe3O4 4 was used as photocatalyst under similar
experimental conditions. This superior photocatalytic activity of 4 was assumed to be due to the
restoration of the sp2 hybridized aromatic system in rGO, which facilitated the movement of electrons
and resulted in better charge separation. The synthesized heterogeneous photocatalyst could readily be
recovered by external magnet and successfully reused for six subsequent cycles without significant loss
in the product yield
Electrooxidation of methanol on carbon supported pt ru nanocatalysts prepared...suresh899
Carbon Supported PtRu nanocatalysts have been prepared by simple impregnation reduction method in which Pt and Ru precursors are reduced by ethanol under reflux conditions for different reaction times. The prepared nanocatalysts were characterized by means of XRD, EDAX, ICP-AAS, FESEM and TEM. XRD analyses showed that all nanocatalysts exhibited f.c.c crystal structure, the structure characteristic for pure Pt, except for that reduced at prolonged reaction time of 4h which showed the presence of characteristic peak for Ru metal. The lattice constant calculations indicate that all catalysts are present in unalloyed phase and the average particle size as determined by TEM was in the range of 3.7 nm. The electrocatalytic activities and stability for the prepared nanocatalysts methanol electro-oxidation reaction (MOR) were studied by cyclic voltammetry. The catalysts prepared at 2h reduction time showed higher electrocatalytic activity in terms of mass specific activity and good stability over potential sweep for 100 cycles for methanol electro-oxidation. The results showed that the prepared nanocatalysts are considered as promising electrode catalyst (anode catalyst) for electro-oxidation of methanol in direct methanol fuel cells.
Parallel Reaction Kinetic Modelling Of Biogas To Biomethanol With Zno/Sio2 Na...IJERD Editor
Kinetic model proposed in this study is a single reaction kinetic model of parallel biogas into
biomethanol (CO2 + H2) and CO2 gas (CO + O2) in the gas phase. The phenomenon of this reaction is a new
breakthrough in the field of renewable energy and very exciting to be modeled kinetic. These parallel reactions
biomethanol and biogas into CO2 gas in this study utilizes content of methane (CH4) which is converted to CO2
by nanoprticles biomethanol and ZnO impregnated silica. Nanoparticles ZnO made with Zn (SO4) 7H2O and
NaOH with co precipitation method with stirring pressure of 1.2 bar and an isothermal drying temperature
180oC. Reaction biogas into biomethanol and CO2 takes place at a temperature of 350oC and a pressure of 1.2
bar produce biogas conversion into biomethanol 70% and 25% CO2 gas. at a temperature of 350oC and
volumetric rate of 5 ml per minute. Effect of water formed in this reaction will inhibit the formation of
biomethanol and hydrocarbons.
PEGylated magnetic nanoparticles (PEG@Fe3O4) as cost effectivealternative for...Pawan Kumar
An efficient, cost effective and environmental friendly PEGylated magnetic nanoparticle catalyzed oxida-tive cyanation via CH activation of tertiary amines to corresponding -aminonitriles using hydrogenperoxide as oxidant and sodium cyanide as cyanide source is described. The synthesized nanocatalyst waseasily recovered with the help of external magnet and was successfully reused for several runs withoutany significant loss in catalytic activity.
PEGylated magnetic nanoparticles (PEG@Fe3O4) as cost effectivealternative for...Pawan Kumar
tAn efficient, cost effective and environmental friendly PEGylated magnetic nanoparticle catalyzed oxida-tive cyanation via CH activation of tertiary amines to corresponding -aminonitriles using hydrogenperoxide as oxidant and sodium cyanide as cyanide source is described. The synthesized nanocatalyst waseasily recovered with the help of external magnet and was successfully reused for several runs withoutany significant loss in catalytic activity.
Effect of Solvent Swelling on the reactivity of demineralized Turkish LigniteIJERA Editor
In this research, effect of demineralization and solvent swelling on pyrolysis kinetics was investigated. The experiments were carried out to investigate theeffects of solvent swelling with different solvents, such as THF, Pyridine and DMSO after demineralization with HCl, HNO3 and HF successively. To calculate the activation energies of lignite sample during pyrolysis, TGA analyses were performed with raw and swollen samples at 5, 10 and 20° C/min heating rates. Coast-Redfernmodel was used for the determination of kinetic parameters. According to the results, the macromolecular structure of lignite was affected from these hydrogen bonding solvents. So, the activation energies of swollen samples found to be less than the raw lignite sample for all heating rates. The reactivity of lignite samples can be ordered as follows; DMSO swollen sample > Pyridine swollen sample> THF swollen sample. Activation energy of DMSO swollen lignite sample is 10.62 kJ/mole whereas activation energies of pyridine swollen and THF swollen sample are 17.83, 25.76 kJ/mol, respectively at a heating rate of 10° C/min. The results indicated that, solvent swelling has catalytic effect on pyrolysis kinetics.
A highly efficient, recyclable and magnetically separable core-shell structured CuZnO@Fe3O4 microsphere
wrapped with reduced graphene oxide (rGO@CuZnO@Fe3O4) photocatalyst has been developed and used
for the photoreduction of carbon dioxide with water to produce methanol under visible light irradiation.
Owing to the synergistic effect of the components and to the presence of a thin Fe2O3 layer on Fe3O4,
rGO@CuZnO@Fe3O4 4 exhibited higher catalytic activity as compared to the other possible combinations
such as CuZnO@Fe3O4 2 and GO@CuZnO@Fe3O4 3 microspheres. The yield of methanol in case of using
2 and 3 as photocatalyst was found to be 858 and 1749 mol g−1 cat, respectively. However, the yield
was increased to 2656 mol g−1 cat when rGO@CuZnO@Fe3O4 4 was used as photocatalyst under similar
experimental conditions. This superior photocatalytic activity of 4 was assumed to be due to the
restoration of the sp2 hybridized aromatic system in rGO, which facilitated the movement of electrons
and resulted in better charge separation. The synthesized heterogeneous photocatalyst could readily be
recovered by external magnet and successfully reused for six subsequent cycles without significant loss
in the product yield
Mechanistic Aspects of Oxidation of P-Bromoacetophen one by Hexacyanoferrate ...IJERA Editor
The kinetics of oxidation of p-bromoacetophenone by hexacyanoferrate (III) has been studied in alkaline
medium. The order of reaction with respect of both acetophenone and hexacynoferrate (III) has been found to be
unity. The rate of reaction increases with increase in the concentration of sodium hydroxide.On addition of
neutral KCl, reaction rate increases. The effects of solvent and temperature have been also studied. The product
p-bromophenyl glyoxal have been characterized by IR studies.
Kinetics and feasibility studies of thiol oxidation using magnetically separa...Pawan Kumar
This work describes kinetic studies of the catalytic oxidation of thiols (RSHs) found in kerosene to disulphides using a magnetically separable iron oxide coated Mg-Al layered double hydroxide supported tetra-sulphonated cobalt phthalocyanine (CoPcS/LDH@Fe3O4) catalyst in an alkali-free environment. Using 1-octanethiol as a representative RSH, we investigated the effects of different experimental parameters on RSH oxidation kinetics, including catalyst concentration, temperature (30–60 °C), and initial thiol concentration ([RSH]0, 100–300 ppm). The catalyst concentration was varied so that the [RSH]0/[Co]tot molar ratio ranged from 45 to 180. Based on the results, we propose a mechanistic rate expression to explain the observed oxidation of RSH in the presence of the CoPcS/LDH@Fe3O4 catalyst. The proposed rate law resembles double substrate Michaelis-Menten kinetics, however, for commonly …
Sunlight-driven water-splitting using two-dimensional carbon based semiconduc...Pawan Kumar
The overwhelming challenge of depleting fossil fuels and anthropogenic carbon emissions has driven research into alternative clean sources of energy. To achieve the goal of a carbon neutral economy, the harvesting of sunlight by using photocatalysts to split water into hydrogen and oxygen is an expedient approach to fulfill the energy demand in a sustainable way along with reducing the emission of greenhouse gases. Even though the past few decades have witnessed intensive research into inorganic semiconductor photocatalysts, their quantum efficiencies for hydrogen production from visible photons remain too low for the large scale deployment of this technology. Visible light absorption and efficient charge separation are two key necessary conditions for achieving the scalable production of hydrogen from water. Two-dimensional carbon based nanoscale materials such as graphene oxide, reduced …
Magnetic Fe3O4@MgAl–LDH composite grafted with cobalt phthalocyanine as an ef...Pawan Kumar
Magnetically separable layered double hydroxide MgAl–LDH@Fe3O4 composite supported cobalt
phthalocyanine catalyst was synthesized and used for the aerobic oxidation of mercaptans to corresponding
disulfides under alkali free conditions. The catalyst exhibited excellent activity for the oxidation of
mercaptans using molecular oxygen as an oxidant which can be effectively recovered by using an external
magnetic field. In addition, the covalent immobilization of cobalt phthalocyanine to MgAl–LDH@Fe3O4
support prevents the leaching of the catalyst and improves its activity and stability
Electro catalytic performance of pt-supported poly (o-phenylenediamine) micro...sunitha81
Poly (o-phenylenediamine) (PoPD) microrods were obtained by interfacial
polymerization using ferric chloride as oxidant and without any template or
functional dopant. Pt/PoPD nanocatalysts were prepared by the reduction of chloroplatinic
acid with sodium borohydride, and the composite catalysts formed were
characterized by X-ray diffraction and electrochemical methods. The nanocomposite
of Pt/PoPD microrods has been explored for their electro-catalytic performance
towards oxidation of methanol. The electro-catalytic activity of Pt/PoPD was
found to be much higher (current density 1.96 mA/cm2 at 0.70 V) in comparison to
Pt/Vulcan electrodes (the current density values of 1.56 mA/cm2 at 0.71 V) which
may be attributed to the microrod morphology of PoPD that facilitate the effective
dispersion of Pt particles and easier access of methanol towards the catalytic sites.
Iron Doped Titania Nanostructures Synthesis, DFT modelling and Photocatalysisioneec
In this work, Fe-doped TiO2 nanoparticles ranging from a 0.2 to 1 weight % were grown from
the surface of graphene sheet templates containing –COOH functionalities using sol–gel
chemistry in a green solvent, a mixture of water/ethanol. The assemblies were characterized by a
variety of analytical techniques, with the coordination mechanism examined theoretically using
the density functional theory (DFT). Scanning electron microscopy and transmission electron
microscopy images showed excellent decoration of the Fe-doped TiO2 nanoparticles on the
surface of the graphene sheets >5 nm in diameter. The surface area and optical properties of the
Fe-doped photocatalysts were measured by BET, UV and PL spectrometry and compared to
non-graphene and pure TiO2 analogs, showing a plateau at 0.6% Fe. Interactions between
graphene and Fe-doped anatase TiO2 were also studied theoretically using the Vienna ab initio
Simulation Package based on DFT. Our first-principles theoretical investigations validated the
experimental findings, showing the strength in the physical and chemical adsorption between the
graphene and Fe-doped TiO2. The resulting assemblies were tested for photodegradation under
visible light using 17β-estradiol (E2) as a model compound, with all investigated catalysts
showing significant enhancements in photocatalytic activity in the degradation of E2.
Reduced graphene oxide–CuO nanocomposites for photocatalyticconversion of CO2...Pawan Kumar
tReduced graphene oxide (rGO)–copper oxide nanocomposites are prepared by covalent grafting of CuOnanorods on the rGO skeleton. Chemical and structural features of rGO–CuO nanocomposites are probedby FTIR, XPS, XRD and HRTEM analyses. Photocatalytic potential of rGO–CuO nanocomposites is exploredfor reduction of CO2into the methanol under the visible light irradiation. The breadth of CuO nanorods andthe oxidation state of Cu in the rGO–CuO/Cu2O nanocomposites are systematically varied to investigatetheir photocatalytic activities. The pristine CuO nanorods exhibited very low photocatalytic activity owingto fast recombination of charge carriers and yielded 175 mol g−1methanol, whereas rGO–Cu2O andrGO–CuO exhibited significantly improved photocatalytic activities and yielded five (862 mol g−1) andseven (1228 mol g−1) folds methanol, respectively. The superior photocatalytic activity of CuO in therGO–CuO nanocomposites was attributed to slow recombination of charge carriers and efficient transferof photo-generated electrons through the rGO skeleton. This study further excludes the use of scavengingdonor.
Visible Light Photocatalytic Degradation of Methylene Blue and Malachite Gree...IJEAB
A facile solid state metathesis synthesis of barium tungstate (BaWO4) followed by ball milling and subsequent preparation of barium tungstate-graphene oxide (BaWO4–GO) nano composite using a colloidal blending process and its application as a visible light photocatalyst for the degradation of Malachite green and Methylene blue dyes. The morphology and composition of barium tungstate (BaWO4) nano composite have been characterized using X-Ray Diffraction (XRD), UV–Visible Diffuse Reflectance Spectra (UV-DRS), Raman Spectra, Field Emission Scanning Electron Microscopy (FESEM) – EDAX and UV Visible Spectroscopy. This composite material is found to be a wide band gap semiconductor with band gap of 4.3 eV. The sample shows poor transmittance in ultraviolet region while it has maximum transmittance in visible-near infrared regions. It shows an increase in range and intensity of light absorption and the reduction of electron–hole pair recombination in BaWO4 with the introducing of GO on to it.
Dynamic and Equilibrium Studies on the sorption of Basic dye (Basic Brown 4) ...madlovescience
Dynamic and Equilibrium Studies on the sorption of Basic dye (Basic Brown 4) onto Multi-walled Carbon Nanotubes Prepared from Renewable Carbon Precursors
Mechanistic Aspects of Oxidation of P-Bromoacetophen one by Hexacyanoferrate ...IJERA Editor
The kinetics of oxidation of p-bromoacetophenone by hexacyanoferrate (III) has been studied in alkaline
medium. The order of reaction with respect of both acetophenone and hexacynoferrate (III) has been found to be
unity. The rate of reaction increases with increase in the concentration of sodium hydroxide.On addition of
neutral KCl, reaction rate increases. The effects of solvent and temperature have been also studied. The product
p-bromophenyl glyoxal have been characterized by IR studies.
Kinetics and feasibility studies of thiol oxidation using magnetically separa...Pawan Kumar
This work describes kinetic studies of the catalytic oxidation of thiols (RSHs) found in kerosene to disulphides using a magnetically separable iron oxide coated Mg-Al layered double hydroxide supported tetra-sulphonated cobalt phthalocyanine (CoPcS/LDH@Fe3O4) catalyst in an alkali-free environment. Using 1-octanethiol as a representative RSH, we investigated the effects of different experimental parameters on RSH oxidation kinetics, including catalyst concentration, temperature (30–60 °C), and initial thiol concentration ([RSH]0, 100–300 ppm). The catalyst concentration was varied so that the [RSH]0/[Co]tot molar ratio ranged from 45 to 180. Based on the results, we propose a mechanistic rate expression to explain the observed oxidation of RSH in the presence of the CoPcS/LDH@Fe3O4 catalyst. The proposed rate law resembles double substrate Michaelis-Menten kinetics, however, for commonly …
Sunlight-driven water-splitting using two-dimensional carbon based semiconduc...Pawan Kumar
The overwhelming challenge of depleting fossil fuels and anthropogenic carbon emissions has driven research into alternative clean sources of energy. To achieve the goal of a carbon neutral economy, the harvesting of sunlight by using photocatalysts to split water into hydrogen and oxygen is an expedient approach to fulfill the energy demand in a sustainable way along with reducing the emission of greenhouse gases. Even though the past few decades have witnessed intensive research into inorganic semiconductor photocatalysts, their quantum efficiencies for hydrogen production from visible photons remain too low for the large scale deployment of this technology. Visible light absorption and efficient charge separation are two key necessary conditions for achieving the scalable production of hydrogen from water. Two-dimensional carbon based nanoscale materials such as graphene oxide, reduced …
Magnetic Fe3O4@MgAl–LDH composite grafted with cobalt phthalocyanine as an ef...Pawan Kumar
Magnetically separable layered double hydroxide MgAl–LDH@Fe3O4 composite supported cobalt
phthalocyanine catalyst was synthesized and used for the aerobic oxidation of mercaptans to corresponding
disulfides under alkali free conditions. The catalyst exhibited excellent activity for the oxidation of
mercaptans using molecular oxygen as an oxidant which can be effectively recovered by using an external
magnetic field. In addition, the covalent immobilization of cobalt phthalocyanine to MgAl–LDH@Fe3O4
support prevents the leaching of the catalyst and improves its activity and stability
Electro catalytic performance of pt-supported poly (o-phenylenediamine) micro...sunitha81
Poly (o-phenylenediamine) (PoPD) microrods were obtained by interfacial
polymerization using ferric chloride as oxidant and without any template or
functional dopant. Pt/PoPD nanocatalysts were prepared by the reduction of chloroplatinic
acid with sodium borohydride, and the composite catalysts formed were
characterized by X-ray diffraction and electrochemical methods. The nanocomposite
of Pt/PoPD microrods has been explored for their electro-catalytic performance
towards oxidation of methanol. The electro-catalytic activity of Pt/PoPD was
found to be much higher (current density 1.96 mA/cm2 at 0.70 V) in comparison to
Pt/Vulcan electrodes (the current density values of 1.56 mA/cm2 at 0.71 V) which
may be attributed to the microrod morphology of PoPD that facilitate the effective
dispersion of Pt particles and easier access of methanol towards the catalytic sites.
Iron Doped Titania Nanostructures Synthesis, DFT modelling and Photocatalysisioneec
In this work, Fe-doped TiO2 nanoparticles ranging from a 0.2 to 1 weight % were grown from
the surface of graphene sheet templates containing –COOH functionalities using sol–gel
chemistry in a green solvent, a mixture of water/ethanol. The assemblies were characterized by a
variety of analytical techniques, with the coordination mechanism examined theoretically using
the density functional theory (DFT). Scanning electron microscopy and transmission electron
microscopy images showed excellent decoration of the Fe-doped TiO2 nanoparticles on the
surface of the graphene sheets >5 nm in diameter. The surface area and optical properties of the
Fe-doped photocatalysts were measured by BET, UV and PL spectrometry and compared to
non-graphene and pure TiO2 analogs, showing a plateau at 0.6% Fe. Interactions between
graphene and Fe-doped anatase TiO2 were also studied theoretically using the Vienna ab initio
Simulation Package based on DFT. Our first-principles theoretical investigations validated the
experimental findings, showing the strength in the physical and chemical adsorption between the
graphene and Fe-doped TiO2. The resulting assemblies were tested for photodegradation under
visible light using 17β-estradiol (E2) as a model compound, with all investigated catalysts
showing significant enhancements in photocatalytic activity in the degradation of E2.
Reduced graphene oxide–CuO nanocomposites for photocatalyticconversion of CO2...Pawan Kumar
tReduced graphene oxide (rGO)–copper oxide nanocomposites are prepared by covalent grafting of CuOnanorods on the rGO skeleton. Chemical and structural features of rGO–CuO nanocomposites are probedby FTIR, XPS, XRD and HRTEM analyses. Photocatalytic potential of rGO–CuO nanocomposites is exploredfor reduction of CO2into the methanol under the visible light irradiation. The breadth of CuO nanorods andthe oxidation state of Cu in the rGO–CuO/Cu2O nanocomposites are systematically varied to investigatetheir photocatalytic activities. The pristine CuO nanorods exhibited very low photocatalytic activity owingto fast recombination of charge carriers and yielded 175 mol g−1methanol, whereas rGO–Cu2O andrGO–CuO exhibited significantly improved photocatalytic activities and yielded five (862 mol g−1) andseven (1228 mol g−1) folds methanol, respectively. The superior photocatalytic activity of CuO in therGO–CuO nanocomposites was attributed to slow recombination of charge carriers and efficient transferof photo-generated electrons through the rGO skeleton. This study further excludes the use of scavengingdonor.
Visible Light Photocatalytic Degradation of Methylene Blue and Malachite Gree...IJEAB
A facile solid state metathesis synthesis of barium tungstate (BaWO4) followed by ball milling and subsequent preparation of barium tungstate-graphene oxide (BaWO4–GO) nano composite using a colloidal blending process and its application as a visible light photocatalyst for the degradation of Malachite green and Methylene blue dyes. The morphology and composition of barium tungstate (BaWO4) nano composite have been characterized using X-Ray Diffraction (XRD), UV–Visible Diffuse Reflectance Spectra (UV-DRS), Raman Spectra, Field Emission Scanning Electron Microscopy (FESEM) – EDAX and UV Visible Spectroscopy. This composite material is found to be a wide band gap semiconductor with band gap of 4.3 eV. The sample shows poor transmittance in ultraviolet region while it has maximum transmittance in visible-near infrared regions. It shows an increase in range and intensity of light absorption and the reduction of electron–hole pair recombination in BaWO4 with the introducing of GO on to it.
Dynamic and Equilibrium Studies on the sorption of Basic dye (Basic Brown 4) ...madlovescience
Dynamic and Equilibrium Studies on the sorption of Basic dye (Basic Brown 4) onto Multi-walled Carbon Nanotubes Prepared from Renewable Carbon Precursors
Maiyalagan,Electrochemical oxidation of methanol on pt v2 o5–c composite cata...kutty79
Platinum nanoparticles have been supported on V2O5–C composite through the reduction of chloroplatinic
acid with formaldehyde. The catalyst was characterized by X-ray diffraction and transmission electron
microscopy. Catalytic activity and stability for the oxidation of methanol were studied by using
cyclic voltammetry and chronoamperometry. Pt/V2O5–C composite anode catalyst on glassy carbon electrode
show higher electro-catalytic activity for the oxidation of methanol. High electro-catalytic activities
and good stabilities could be attributed to the synergistic effect between Pt and V2O5, avoiding the electrodes
being poisoned.
Maiyalagan, Synthesis and electro catalytic activity of methanol oxidation on...kutty79
Template synthesis of various nitrogen containing carbon nanotubes using different nitrogen containing polymers and the variation of nitrogen
content in carbon nanotube (CNT) on the behaviour of supported Pt electrodes in the anodic oxidation of methanol in direct methanol fuel cells was
investigated. Characterizations of the as-prepared catalysts are investigated by electron microscopy and electrochemical analysis. The catalyst with
N-containing CNT as a support exhibits a higher catalytic activity than that carbon supported platinum electrode and CNT supported electrodes.
The N-containing CNT supported electrodes with 10.5% nitrogen content show a higher catalytic activity compared to other N-CNT supported
electrodes. This could be due to the existence of additional active sites on the surface of the N-containing CNT supported electrodes, which favours
better dispersion of Pt particles. Also, the strong metal-support interaction plays a major role in enhancing the catalytic activity for methanol
oxidation.
The present work demonstrates for the first time the facile fabrication of TiO2
nanotube arrays (TNTAs) by a fluoride-free
solid-state anodization process using LiClO4
containing solid polymeric electrolyte. The resulting nanotubes were tested
for photoelectrochemical water splitting. The elimination of liquid electrolytes in electrochemical anodization constitutes
a paradigm shift for the formation of nanoporous and nanotubular metal oxides. Our results open a new area of research
that uses the distinctive properties of solid polymer electrolytes to achieve targeted doping and nano-morphologies. Characterization
of the grown TNTAs indicated solid state anodized TNTAs to consist purely of the anatase phase of titania.
The solid-state anodization process provides several advantages over conventional liquid electrolytes such as easy handling
and processing, better charge transport, environmentally benign chemicals and methodology. Photoelectrochemical water
splitting experiments were performed which confirmed the viability of TNTAs grown by the new solid-state process for
photocatalytic applications.
Similar to Electrooxidation of methanol on carbon supported pt ru nanocatalysts prepared by ethanol reduction method (20)
The French Revolution, which began in 1789, was a period of radical social and political upheaval in France. It marked the decline of absolute monarchies, the rise of secular and democratic republics, and the eventual rise of Napoleon Bonaparte. This revolutionary period is crucial in understanding the transition from feudalism to modernity in Europe.
For more information, visit-www.vavaclasses.com
We all have good and bad thoughts from time to time and situation to situation. We are bombarded daily with spiraling thoughts(both negative and positive) creating all-consuming feel , making us difficult to manage with associated suffering. Good thoughts are like our Mob Signal (Positive thought) amidst noise(negative thought) in the atmosphere. Negative thoughts like noise outweigh positive thoughts. These thoughts often create unwanted confusion, trouble, stress and frustration in our mind as well as chaos in our physical world. Negative thoughts are also known as “distorted thinking”.
How to Make a Field invisible in Odoo 17Celine George
It is possible to hide or invisible some fields in odoo. Commonly using “invisible” attribute in the field definition to invisible the fields. This slide will show how to make a field invisible in odoo 17.
Instructions for Submissions thorugh G- Classroom.pptxJheel Barad
This presentation provides a briefing on how to upload submissions and documents in Google Classroom. It was prepared as part of an orientation for new Sainik School in-service teacher trainees. As a training officer, my goal is to ensure that you are comfortable and proficient with this essential tool for managing assignments and fostering student engagement.
How to Create Map Views in the Odoo 17 ERPCeline George
The map views are useful for providing a geographical representation of data. They allow users to visualize and analyze the data in a more intuitive manner.
Synthetic Fiber Construction in lab .pptxPavel ( NSTU)
Synthetic fiber production is a fascinating and complex field that blends chemistry, engineering, and environmental science. By understanding these aspects, students can gain a comprehensive view of synthetic fiber production, its impact on society and the environment, and the potential for future innovations. Synthetic fibers play a crucial role in modern society, impacting various aspects of daily life, industry, and the environment. ynthetic fibers are integral to modern life, offering a range of benefits from cost-effectiveness and versatility to innovative applications and performance characteristics. While they pose environmental challenges, ongoing research and development aim to create more sustainable and eco-friendly alternatives. Understanding the importance of synthetic fibers helps in appreciating their role in the economy, industry, and daily life, while also emphasizing the need for sustainable practices and innovation.
Read| The latest issue of The Challenger is here! We are thrilled to announce that our school paper has qualified for the NATIONAL SCHOOLS PRESS CONFERENCE (NSPC) 2024. Thank you for your unwavering support and trust. Dive into the stories that made us stand out!
The Roman Empire A Historical Colossus.pdfkaushalkr1407
The Roman Empire, a vast and enduring power, stands as one of history's most remarkable civilizations, leaving an indelible imprint on the world. It emerged from the Roman Republic, transitioning into an imperial powerhouse under the leadership of Augustus Caesar in 27 BCE. This transformation marked the beginning of an era defined by unprecedented territorial expansion, architectural marvels, and profound cultural influence.
The empire's roots lie in the city of Rome, founded, according to legend, by Romulus in 753 BCE. Over centuries, Rome evolved from a small settlement to a formidable republic, characterized by a complex political system with elected officials and checks on power. However, internal strife, class conflicts, and military ambitions paved the way for the end of the Republic. Julius Caesar’s dictatorship and subsequent assassination in 44 BCE created a power vacuum, leading to a civil war. Octavian, later Augustus, emerged victorious, heralding the Roman Empire’s birth.
Under Augustus, the empire experienced the Pax Romana, a 200-year period of relative peace and stability. Augustus reformed the military, established efficient administrative systems, and initiated grand construction projects. The empire's borders expanded, encompassing territories from Britain to Egypt and from Spain to the Euphrates. Roman legions, renowned for their discipline and engineering prowess, secured and maintained these vast territories, building roads, fortifications, and cities that facilitated control and integration.
The Roman Empire’s society was hierarchical, with a rigid class system. At the top were the patricians, wealthy elites who held significant political power. Below them were the plebeians, free citizens with limited political influence, and the vast numbers of slaves who formed the backbone of the economy. The family unit was central, governed by the paterfamilias, the male head who held absolute authority.
Culturally, the Romans were eclectic, absorbing and adapting elements from the civilizations they encountered, particularly the Greeks. Roman art, literature, and philosophy reflected this synthesis, creating a rich cultural tapestry. Latin, the Roman language, became the lingua franca of the Western world, influencing numerous modern languages.
Roman architecture and engineering achievements were monumental. They perfected the arch, vault, and dome, constructing enduring structures like the Colosseum, Pantheon, and aqueducts. These engineering marvels not only showcased Roman ingenuity but also served practical purposes, from public entertainment to water supply.
Welcome to TechSoup New Member Orientation and Q&A (May 2024).pdfTechSoup
In this webinar you will learn how your organization can access TechSoup's wide variety of product discount and donation programs. From hardware to software, we'll give you a tour of the tools available to help your nonprofit with productivity, collaboration, financial management, donor tracking, security, and more.
Welcome to TechSoup New Member Orientation and Q&A (May 2024).pdf
Electrooxidation of methanol on carbon supported pt ru nanocatalysts prepared by ethanol reduction method
1. Int. J. Electrochem. Sci., 6 (2011) 379 - 393
International Journal of
ELECTROCHEMICAL
SCIENCE
www.electrochemsci.org
Electrooxidation of Methanol on Carbon Supported PtRu Nanocatalysts Prepared by Ethanol Reduction Method
A. B. Kashyout1,*, Abu Bakr A.A. Nassr1, 2, Leonardo Giorgi2, T. Maiyalagan3,
Bayumy A. B. Youssef 4
1
Electronic Materials Department, Advanced Technology and New Materials Research Institute,
Mubarak City for Scientific Research and Technology Applications, 21934 New Borg El-Arab City,
Alexandria, Egypt.
2
ENEA, Casaccia Research Centre, Department of Physical Technologies and New Materials, Via
Anguillarese 301, 00123 S. Maria di Galeria, Rome, Italy
3
Department of Chemistry, VIT University, Vellore-632014, India
4
Department of Computer Based Engineering Applications, Informatics Research Institute, Mubarak
City for Scientific Research and Technologies Applications, 21934 New Borg El-Arab City,
Alexandria, Egypt
*
E-mail: akashyout@mucsat.sci.eg
Received: 26 January 2010 / Accepted: 1 December 2010 / Published: 1 February 2011
Carbon Supported PtRu nanocatalysts have been prepared by simple impregnation reduction method in
which Pt and Ru precursors are reduced by ethanol under reflux conditions for different reaction times.
The prepared nanocatalysts were characterized by means of XRD, EDAX, ICP-AAS, FESEM and
TEM. XRD analyses showed that all nanocatalysts exhibited f.c.c crystal structure, the structure
characteristic for pure Pt, except for that reduced at prolonged reaction time of 4h which showed the
presence of characteristic peak for Ru metal. The lattice constant calculations indicate that all catalysts
are present in unalloyed phase and the average particle size as determined by TEM was in the range of
3.7 nm. The electrocatalytic activities and stability for the prepared nanocatalysts methanol electrooxidation reaction (MOR) were studied by cyclic voltammetry. The catalysts prepared at 2h reduction
time showed higher electrocatalytic activity in terms of mass specific activity and good stability over
potential sweep for 100 cycles for methanol electro-oxidation. The results showed that the prepared
nanocatalysts are considered as promising electrode catalyst (anode catalyst) for electro-oxidation of
methanol in direct methanol fuel cells.
Keywords: PtRu nanocatalysts, methanol electro-oxidation, cyclic voltammetry, DMFCs
2. Int. J. Electrochem. Sci., Vol. 6, 2011
380
1. INTRODUCTION
The electro-oxidation of small organic molecules on Pt electrocatalysts based electrodes has
received more attention in the last decades due their application for electrochemical energy conversion
in direct liquid feed fuel cells [1-3]. Among these molecules; methanol is used as liquid fuel for direct
methanol fuel cells (DMFCs). It has a higher electron density (six electron production during its
electro-oxidation) and it has a good electrochemical activity due to the presence of electroactive
hydroxyl group which can be attached or adsorbed to the electrode surface [4].
The electro-oxidation of methanol has been studied on many electrode fabricated from
unsupported metals and metal supported onto different supporting materials. Pt catalysts are still the
most active catalysts materials for electro-oxidation of methanol [3, 5-9]. The electro-oxidation of
methanol on Pt electrode surface is combined with several steps of dehydrogenation to form CO which
is oxidized into CO2 [10, 11]. The poisoning of the electrode surface (anode) by CO molecules formed
during the methanol oxidation is one of the obstacles in the development of DMFCs for commercial
applications. The modification of Pt catalysts with other metals or metal oxides which have higher
tendency to form surface oxygenated species at lower potential is considered as one of the best ways to
solve this problem [12, 13]. In this regard, many efforts have been done by many groups to synthesis
new catalysts systems for methanol oxidation based on bimetallic catalysts such as PtRu[14-17],
PtSn[18,19], PtNi[20,21], PtMo[22,23],ternary alloy ; PtRuNi[24-26], PtRuMo[25,27,28], and PtMOx
(where M is, Ti, V, Mn, W) [29-32].
Among all catalyst systems, PtRu catalysts prepared as nanoparticles have received more
attention due to its high CO tolerance. The formation of surface oxygenated species on Ru takes place
at a potential lower than that on Pt. So, the presence of Ru adjacent to Pt reduces the poisoning of Pt
surface by CO [8,9]. In this catalyst system, Pt services as active sites for methanol adsorption and
dehydrogenation while Ru serves as catalyst promoter on which CO is oxidized into CO 2. This model
mechanism is known as bifunctional mechanism. Other model is suggested based on electronic
structure change upon addition of Ru. According to this model, the addition of Ru can change the
electronic structure of catalyst surface which lead to decrease the bonding between the CO molecules
and Pt catalyst surface [8, 9, 33].
Many research groups are working to explore preparation method for PtRu catalyst system [7].
The catalytic activity of the catalysts depends on their preparation methods. Also, the cost of catalysts
preparation process should be taken into consideration for the application in fuel cells. Therefore; the
searching for simple preparation methods with low cost and high catalytic activity will lead to the
development of fuel cells industry.
Wet chemical method or some times called chemical impregnation method is considered as the
most powerful method for preparation of catalysts nanoparticles specially; supported PtRu catalysts.
The procedures for this method are easy and can be developed for large-scale production [7, 34]. In
wet chemical method, the metal precursors are impregnated on the carbon support in aqueous or/and
organic media followed by the reduction using reducing agent such as sodium borohydride, formic
acid, hydrazine. Also, the organic alcohols (methanol, ethanol, isopropanol and ethylene glycol,
glycerol and diethylene glycol) are known as good reducing agents for the preparation of PtRu and
3. Int. J. Electrochem. Sci., Vol. 6, 2011
381
other nanoparticles. Advantages of using alcohols as reducing agent are that there is no side reaction
products can be obtained and the formation of relative pure nanoparticles are well synthesized
[7,34,35].
The reduction process are carried out in presence of stabilizers such as PVA or other polymers
or surfactant materials which serve as capping agent to prevent the particle agglomeration. In fact,
these capping materials have adverse effect on the electrocatalytic activity, since these stabilizers are
adsorbed on the surface of the nanoparticles catalysts and blocking the active sites available for the
electrochemical reaction in addition to its lower electrical conductivity. Also, the removal of these
protective agents by heat treatment may be has side-effect on the electrocatalytic activity due the
change of crystal structure of the active phase in the catalysts or increase their particle size [36, 37].
Lee e.t al. prepared PtRu/C nanocataysts using ethanol reduction method and tested the
prepared catalysts for methanol electooxidation reaction [38]. The results showed that the preparation
process has adverse effect on the electrocatalytic activity when carried out in alkaline media. Also,
carbon supported Pt and PtAu catalysts as electrocatalysts for oxygen reduction reaction (ORR) have
been prepared by ethanol reduction method in the presence of PVP as stabilizing and complexing
agent. The reduction process were carried out in alkaline media. The removal of the stabilizing agent
was carried out by heating the catalysts at high temperature in air followed by their reduction in flow
of hydrogen at elevated temperature. The prepared electrocatalysts showed good electrocatalytic
activity towards ORR [39].
In this work, we report a simple method for preparation of PtRu nanoparticles supported on
carbon support (Vulcan XC-72R) by using ethanol as a reducing agent without using any stabilizers
and no modification of the preparation media (pH) and without heat treatment. The prepared
nanocatalysts are characterized by means of structural tools; XRD, FESEM and TEM and chemical
analyses by EDAX and ICP-AAS. The electrocatalytic activity is tested for methanol electrooxidation
by cyclic voltammetry technique. The effect of reduction time on the durability of the catalysts is also
studied.
2. EXPERIMENTAL PART
2.1. Electrocatalyst Preparation
In this work, a carbon supported PtRu nanoparticles electrocatalyst with atomic ratio Pt:Ru
(1:1) and 20% wt of metal loading (PtRu) on carbon was prepared according to the following
procedures. 100 mg of carbon (Vulcan XC-72R) was dispersed in 20 ml ethanol in an ultrasonic bath
for 15 min. To the above suspension; 34.6 mg of H2PtCl6 dissolved in 5 ml water and 17.5 mg of
RuCl3 dissolved in 5 ml of water were added and then 80 ml of ethanol was also added to the reaction
mixture. The total mixture was kept under stirring for 1h followed by sonication in an ultrasonic bath
for 30 min to insure the adsorption and dispersion of the metal precursors on the carbon support. The
resulted mixture was heated under reflux at (80 ± 2°C) under stirring for different reaction times after
which the reaction mixture was leaved to cool to room temperature and then centrifuged to separate the
4. Int. J. Electrochem. Sci., Vol. 6, 2011
382
catalysts powder. The catalysts were subjected to many cycles of washing with water and centrifuge
until no Cl – ions were detected (silver nitrite test) and then dried in vacuum oven at 100°C for 12h.
The reductive reactions can be represented by the following equations [38]:
H2PtCl6 + 2C2H5OH → Pt + 2 CH3CHO + 6 HCl
2RuCl3 + 3C2H5OH
→ 2Ru + 2 CH3CHO + 6 HCl
The PtRu/C catalysts produced during this work are (PtRu/C1, PtRu/C2 and PtRu/C4). These
labels are giving according to their reaction times of 1h, 2h and 4h; respectively.
2.2. Electrocatalyst Characterization
2.2.1. Physical and Chemical Characterization
The total metal loading was determined by ICP-AAS (Prodigy, high dispersion ICP, Leman).
The measurement was carried out by collecting all the filtrates during the washing process and
determining the concentration of Pt and Ru contents in the filtrate from which we can calculate the
amount of metal loading on the carbon support. The chemical composition of the prepared catalysts
was determined by the energy dispersive X-ray analysis (EDAX) combined with SEM (JEOL JSM
6360LA). X-ray diffraction study of the prepared nanocatalysts were carried out using (Schimadzu
7000) diffractometer, operating with Cu Kα radiation (λ=0.154060 nm) generated at 30 kV and 30 mA
with scanning rate of 2º min-1 for 2θ values between 20 and 90º degree. The nanocatalysts morphology
and dispersion on the support and their particle size were investigated by FESEM (LEO 1530) and
TEM (JEOL, 200CX). The samples were prepared by dispersion of the catalysts powder in ethanol and
sonication, then the sample was deposited on a diamond polished graphite paper supported on
aluminum sample holder for FESEM analysis and on carbon coated Cu grid for TEM analysis.
The average particle size and particle size distribution are acquired using FORTRAN code. The
code has been made to apply the image processing rules on the TEM images of PtRu/C catalysts to
determine exactly the average particle size and the particles size distribution from digital images.
The code design steps are removing the background (the carbon support), clustering the pixels
which form each particle and finally computing the diameter of each particle [40]. Removing of
background has been done using the threshold technique. For clustering of the pixels; the clustering
based iterative method has been used. The method mainly depends on getting certain relation between
each pixel and its neighbors. This relation is applied iteratively until the results of this relation have no
variation with increasing the iteration:
1.
Starting with two arrays (A, B) which have a number of elements. Each element is
corresponding to each pixel of image.
5. Int. J. Electrochem. Sci., Vol. 6, 2011
2.
383
Fill the arrays A and B with large number. This number must be greater than the expected
particles number (LN)
3.
Putting a variable N as counter for particle Number
4.
Starting N=0
5.
Calculating every array elements according the next relation:
Bi , j Min( Ai 1, j , Ai 1, j , Ai , j 1 , Ai , j 1 )
6.
If Ai , j is equal to the larger number LN then N N 1 and Ai , j N
7.
If Ai , j is less than (LN) , Ai , j remains unchanged
8.
Getting r A B
9.
If r equal zero the solution is accomplished if not the program must execute steps 5,6,7,8,9
after putting A B
Finally, the array A contains the particle numbers corresponding to all pixels of the image.
From the total number of pixel we calculated the area of each particle which subsequently used to
calculate the particle size.
2.2.2. Electrochemical Measurements
The electrocatalytic activities of the prepared catalysts were evaluated towards methanol
electrooxidation reaction (MOR) in a standard three electrodes electrochemical cell in which statured
calomel electrode (SCE) (0.241 vs. NHE) and high purity graphite electrode were used as reference
electrode and counter electrode; respectively. The working electrode is glass carbon disc (GCD)
electrode coated with the catalyst layer. The catalysts layer was prepared by mixing the catalyst
powder with Nafion solution (10% Wt , DuPont), water and isopropanol and then sonicated in
ultrasonic water bath for 15 min followed by magnetic stirring for1h to form a catalyst ink which
finally coated on GCD and dried for 20 min at 80 ºC. The working electrode area was 0.79 cm2 and the
amount of catalysts loading (PtRu in mg/cm2) in the working electrode was controlled to be 0.2
mg/cm2. The measurements were carried out with EG&G 273A potentiostat/galvanostat from
Princeton Applied Research (PAR) and controlled with Corware/Corview software (Scribner
Associates). The electrode measurements were activated in 1M H2SO4 by sweep the electrode between
-0.28 – 1 V (SCE) with a scan rate of 100 mVs-1 till the reproducible voltammogram was obtained
(about 100 cycles). The electrocatalytic activity for methanol electro-oxidation was tested in 0.5 M
CH3OH/1 M H2SO4 solution in the same potential window and at the same scan rate. Before the
electrochemical measurements, the cell was bubbled with N2 gas for at least 20 min and the N2 gas
flow was maintained over the solution surface during the measurements. All chemicals during this
6. Int. J. Electrochem. Sci., Vol. 6, 2011
384
work were an analytical reagent grade and the solutions were prepared from distilled water. The
measurements were carried out at room temperature.
3. RESULTS AND DISCUSSION
3.1. Physical and chemical characterization
3.1.1. Chemical composition analysis
Metal atomic composition (Pt:Ru, atomic ratio) and weight percent determined by EDAX and
the ICP are shown in Table (1). Pt:Ru is very closed to 1:1 atomic ratio which agrees with the nominal
concentration of Pt and Ru in the starting precursor. During the EDAX analysis, no peaks for Cl or Na
were observed, which insure that these undesirable elements were removed during the washing
process. On the other hand, ICP analyses showed that the PtRu loading was 18 wt% for all catalysts
which is near to the starting loading percentage of 20 % and confirms that almost all the Pt and Ru ions
are reduced to their corresponding metallic state.
Table 1. Chemical composition of PtRu/C catalysts from EDAX and ICP-ASS Analyses
Catalysts Type Reaction time
hr
PtRu/C1
1
PtRu/C2
2
PtRu/C4
4
At % (from EDAX)
Pt
Ru
47.59
52.41
48.05
51.95
45.11
54.89
Wt % (From ICP-Ass)
Pt
Ru
11
7
11
7
11
7
3.1.2. X-ray diffraction
Fig.(1) shows the X-ray diffraction patterns for the prepared catalysts, e.g. PtRu/C1, PtRuC2
and PtRuC3 respectively. X-ray diffraction analyses show that all catalysts exhibit the diffraction
peaks of (111), (200), (220) and (311), respectively.
Table (2): Diffraction peaks for PtRu/C catalysts and pure Pt with their corresponding 2θ value
Catalysts Type
(111)
(200)
(220)
(311)
Pure Pt
39.7º
46.2º
67.4º
81.2º
PtRu/C1
39.8º
46.2º
67.8º
81.6º
PtRu/C2
39.8º
46.2º
67.7º
81.6º
PtRu/C4
39.9º
46.1º
67.8º
81.6º
These peaks are the characteristic for Pt face-centered cubic structure (f.c.c) (JCPDS Card No.
04-802). The wide peak near 2θ = 25° corresponds to the diffraction of the carbon support (Vulcan
7. Int. J. Electrochem. Sci., Vol. 6, 2011
385
XC-72R). The diffraction peaks are located approximately at nearly 2θ values as that of pure metallic
Pt as shown in Table 2. Since there is no shift of the diffraction peaks for higher 2θ value than that of
pure Pt, no alloys formation or solid solution between Pt and Ru in the prepared PtRu/C can be
detected which is in agree with the results of lattice constant calculated for all the prepared catalysts
(Table. 3) [41].
350
(111)
(PtRu/C4)
(200)
Intensity (a.u)
(220)
(311)
(PtRu/C2)
(PtRu/C1)
20
30
40
50
60
70
80
90
2 (Degree)
Figure 1. XRD patterns for PtRu/C catalysts prepared at different reaction time.
For the catalysts PtRu/C1 and PtRu/C2, there are no diffraction peaks characteristic for
Ru or its oxide, even with the smooth profile obtained after elimination of the back ground and high
frequency noise by the instrumental software. The same results are reported by many groups for
PtRu/C catalysts [41-43] and this may be attributed to Pt that is decorated by Ru particles or may be
Ru is present in amorphous phase or in form of hydrous Ru-oxide [43-46]. For PtRu/C4 catalyst, there
is a new low intensity diffraction peak at about 2θ =44° between those of Pt (111) and (200). The peak
was detected from the smooth profile of XRD pattern for PtRu/C4. This peak is the characteristic for
(101) diffraction plane of Ru, most intense reflection plane for h.c.p Ru [46]. This suggests that in
PtRu/C4, Ru is presence as a separate phase.
The particle size for all the prepared catalysts is calculated from the width of (220) diffraction
peak using Gaussian fitting using Scherer equation [42,43,47]:
D
0.95
2 cos max
Where D is the particle size in (nm), λ is the wave length (0.15406 nm), β2θ is the fullwidth at
half maxima in radius and θmax is the angle at high maxima.
8. Int. J. Electrochem. Sci., Vol. 6, 2011
386
The lattice constant for the prepared catalysts was calculated from (220) diffraction peak by
using Bragg law according to the following equation [42, 43]:
a fcc
2
sin
The particle size and the lattice constant for all prepared catalysts are given in Table (3). For all
the prepared catalysts, the calculated particle size is nearly equal to about 3.7 and 3.8 nm which
indicates that the particle size is slightly influenced by the reaction time.
Also, the lattice constants for all the catalysts are much closed to that of pure Pt which confirms
that PtRu catalysts are present in unalloyed form.
The relative crystallinity of the prepared catalysts can be calculated from the ratio between the
height peak of Pt (111) and peak reflection of the carbon. These values of relative crystallinity are
given in Table (3). From Table (3), catalysts PtRu/C2 has a higher crystallinity than that of PtRu/C1
and PtRu/C4.
Table 3. The structural parameters for PtRu/C catalysts from XRD analysis and average particle size
from TEM calculations.
Catalysts type Particle size Lattice constant
Relative crystallinity Average
particle size
XRD (nm)
(nm)
TEM (nm)
PtRu/C1
4.9
0.3906
4.85
3.7
PtRu/C2
4.9
0.3908
5
3.7
PtRu/C4
4.7
0.3906
3
3.8
PtRu/C [38].
-
-
-
6.96
3.1.3. FESEM and TEM analysis
Fig (2) and Fig (3) show the FESEM and TEM images of the synthesized PtRu/C catalysts.
From both FESEM and TEM images we observe the deposits of PtRu nanoparticles on the carbon
support. The nanoparticles are in good dispersion on the support.
For PtRu/C4, the presence of large amount of agglomeration is observed and some of the
carbon particles were not covered by PtRu nanoparticles.
The histograms for particle size distribution are shown in Fig (3). The average particle sizes
were 3.7, 3.7, 3.8 for PtRu/C1, PtRu/C2, PtRu/C4; respectively.
The average particle for PtRu/C catalysts reported in this work is smaller than that reported by
Lee et al using the same preparation method, which was 6.96 nm and 10.2 nm upon addition of 1M
NaOH. [38]
10. Int. J. Electrochem. Sci., Vol. 6, 2011
388
30
Particle size =3.7
S.D.= 1.1
Frequency %
25
20
15
10
5
0
2.5
3
3.5
4
4.5
5
5.5
6
Particle size (nm)
30
Particle Size =3.7
S.D.= 0.96
Frequency %
25
20
15
10
5
0
2.5
3
3.5
4
4.5
5
6
Particle size (nm)
25
Particle size =3.8
S.D.= 1.05
Frequency %
20
15
10
5
0
1
2
3
4
5
6
7
8
Particle size (nm)
Figure 3. TEM photographs for PtRu/C catalysts (PtRu/C1;(a), PtRu/C2; (b), PtRu/C4; (c)) and the
corresponding histograms.
3.2. Electrochemical measurements
The cyclic voltammograms for PtRu/C catalysts in H2SO4 are shown in Fig (4, column A). The
PtRu/C1 and PtRu/C4 showed the typical behavior of Pt electrode in H2SO4 with peaks in hydrogen
11. Int. J. Electrochem. Sci., Vol. 6, 2011
389
adsorption-desorption region (-0.2– 0.15 V vs. SCE) and a peak for PtOx reduction in the reverse scan.
The characteristic peaks were well defined in case of PtRu/C1 than that on PtRu/C4. It appears from
these characteristics that the two catalysts have Pt-rich surface. On the other hand, for PtRu/C2, the Hdesorption peaks are very low and the peak for PtOx is suppressed completely. It is reported that the
behavior of Pt catalyst electrode in H2SO4 is affected by the incorporation of Ru and its percent on the
surface and PtRu catalysts with 50 At. % doesn't show the same behavior of Pt catalysts. The
suppressed of hydrogen desorption process in PtRu/C2 may be attributed to the formation RuOx at
lower potential and it could be due to the presence of hydrous Ru-oxide [45].
The CV’s for methanol oxidation on all prepared catalysts electrodes are shown in Fig (4,
column B). All cyclic voltammograms are similar to methanol oxidation voltammograms reported in
the literature [32, 46], with the peak for oxidation of methanol in the forward scan and another peak in
backward scan characteristic for oxidation of intermediate adsorbed on the electrode surface in the
forward scan. For the PtRu/C4, the peak potential for methanol oxidation is shifted for higher potential
than that of other catalysts. This may be attributed to the agglomeration of nanoparticles catalysts as it
detected by FESEM and TEM. The high dispersion and uniform distribution of nanoparticles catalysts
in the carbon supports could enhance the electrocatalytic activity of the nanocatalysts. The
electrocatalytic activities for all the catalysts are evaluated using mass specific activity (MSA) and
peak potential for methanol electrooxidation. The MSA was calculated by integration of the charge
density corresponding for methanol oxidation divided by metal loading according to the following
equation [48-50]:
Q
MSA MOR
LPtRu
Where the MSA is the mass specific activity for MOR (mCmg-1), QMOR is the charge density
for methanol oxidation peak (mC/cm2) and LPtRu is the loading of PtRu in the electrode (mg/cm2)
The values for mass specific activities for all catalysts electrodes at steady state (after 50
cycles) and the peak potential for methanol electrooxidation are shown in Table (4).
Table 4.Mass specific activities for PtRu/C catalysts
Catalysts type
PtRu/C1
PtRu/C2
PtRu/C4
MSA (mCmg-1)
175
196
165
CH3OH oxidation peak potential (V)
0.69
0.68
0.75
PtRu/C2 showed higher MSA which indicates that the electrode fabricated from this catalyst has
higher electrocatalytic activity towards methanol electro-oxidation reaction. This higher
electrocatalytic activity of PtRu/C2 could be attributed to high dispersion or more homogenous of
nanoparticles catalysts on the support and the formation of hydrous ruthenium oxide. It is reported that
the hydrous ruthenium oxide has promoter effect in PtRu catalysts more than that the Ru alloyed in
PtRu [51]
12. Int. J. Electrochem. Sci., Vol. 6, 2011
390
(A)
225
0
150
mA/cm
2
mA/mgPtRu
10
-10
-20
-30
-40
10
-0.4 -0.2 0.0 0.2 0.4 0.6 0.8 1.0 1.2
PtRu/C4
225
-0.4 -0.2 0.0 0.2 0.4 0.6 0.8 1.0 1.2
150
mA/mgPtRu
2
mA/cm
0
-150
0
-10
-20
-30
75
-75
PtRu/C4
(B)
75
0
-75
PtRu/C2
-40
PtRu/C2
-150
-0.4 -0.2 0.0 0.2 0.4 0.6 0.8 1.0 1.2
225
0
-0.4 -0.2 0.0 0.2 0.4 0.6 0.8 1.0 1.2
150
mA/mgPtRu
mA/cm
2
10
-10
-20
-30
PtRu/C1
-40
75
0
-75
PtRu/C1
-150
-0.4 -0.2 0.0 0.2 0.4 0.6 0.8 1.0 1.2
P o t e n t i a l (V) vs. S C E
-0.4 -0.2 0.0 0.2 0.4 0.6 0.8 1.0 1.2
P o t e n t i a l (V) vs. S C E
Figure 4. Cyclic voltammograms for PtRu/C electrocatalysts in 1M H2SO4 (column, A) and 0.5M
CH3OH/1M H2SO4 (column, B) (scan rate 100 mV/sec).
For methanol electro-oxidation potential peaks, PtRu/C2 showed lower peak potential among
all catalysts which indicate that this catalyst has good electrocatalytic activity for methanol
electrooxidation. On the other side, PtRu/C4 showed higher peak potential which could be attributed to
the presence of large agglomeration in this catalyst that could retard the oxidation of methanol at lower
potential. The peak potentials for methanol oxidation on the catalysts prepared in this work are very
13. Int. J. Electrochem. Sci., Vol. 6, 2011
391
closed to the peak potential for methanol oxidation on PtRu supported on acid functionalized carbon
nanotubes (PtRu/CNTs) reported by Chetty et.al.and prepared by impregnation in ethanol followed by
reduction at high temperature with flow of hydrogen and helium[46].
To test the durability and stability of electrode catalysts to be applicable in DMFCs, all
electrodes were cycled in methanol for 100 cycles of potential sweep. The MAS activities for all
electrodes against cycle number of potential sweep are plotted in Fig (5). PtRu/C1 showed a decay for
MSA and it decreases rapidly with increasing the cycle number. On the other hand for other electrodes,
the MSA activities start low but increases with cycling, which is an indication that the cycling process
activates the electrode for methanol oxidation by adsorption of more methanol molecules and then the
MSA is extremely stabilized. From Fig (5) we can detect that PtRu/C2 has higher MSA and good
stability, which futures this catalyst to be a promising catalyst electrode for methanol electro-oxidation
in DMFCs.
260
PtRu/C1
PtRu/C2
PtRu/C4
240
220
-1
MSA (mCmg )
200
180
160
140
120
100
80
60
40
0
10
20
30
40
50
60
70
Cycle Number
80
90
100
110
Figure 5. The MSA activities for PtRu/C catalysts electrodes as function of cycle number of potential
sweep in 0.5M CH3OH/1M H2SO4.
4. CONCLUSIONS
The carbon supported PtRu nanocatalysts have been synthesized using a simple impregnation
reduction method in ethanol as solvent and reducing agent at the same time. The XRD characterization
showed that all catalysts exhibit f.c.c structure phase and only Ru h.c.p structure phase can be detected
at higher reaction time. From lattice constant calculations, the prepared catalysts are present in
unalloyed form.
14. Int. J. Electrochem. Sci., Vol. 6, 2011
392
The PtRu nanoparticles showed a good dispersion on the support and the average particle size
was in range of 3.7 nm with narrow particles distribution for PtRu/C prepared at 2h (PtRu/C2). The
electrocatalytic activities of nanocatalysts evaluated in terms of mass specific activity. Among all
catalysts, PtRu/C2 showed higher electrocatalytic activity for methanol electro-oxidation. This work
indicate how the reaction time and therefore the morphological feature influence the electrocatalytic
activity despite that all catalysts almost have the same crystal structure and the particle size. An
optimum reaction time of 2h was able to produce nanoparticles with good dispersion and narrow
particle size distribution which enhance the catalytic activity. The work demonstrates that ethanol
impregnation reduction method is simple and low cost method for preparation of nanocatalysts as
promising materials for application in direct methanol fuel cells.
ACKNOWLEDGMENTS
The authors are provided thanks for Emanuele Serra and Elena Salernitano, ENEA, Casaccia Research
Centre, for the FESEM analyses and for help during the work. One of the authors, Abu Bakr A.A.
Nassr is grateful thanks for Abdus Salam International Centre for Theoretical Physics (ICTP) and
International Italian Agency for New Technologies; Energy and Environment (ENEA) for (ICTPENEA) fellowship on Training and Research in Italian Laboratories programme (TRIL- programme).
References
1. E. L. Gyenge, Chapter 4: Electrocatalytic oxidation of methanol, ethanol and formic acid’, in
PEM Fuel Cell Electrocatalysts and Catalyst Layers, editor; Jiujun Zhang, Springer, New York, p.
165-270 (2008).
2. A. O. Neto, R. W. R. Verjulio-Silva, M. Linardi and E.V. Spinacé, Int. J. Electrochem. Sci., 4
(2009) 954.
3. A. B. Kashyout, A. A. A. Nasr, M. S. Mohy Eldin , Alexandria Engineering Journal, 48 (2009)
491.
4. G.T. Burstein, C.J. Barnett, A.R. Kucernak, K.R. Williams; Catal. Today 38 (1997) 425.
5. T. Iwasita, Electrochim. Acta 47 (2002) 3663.
6. M. Brandalise, M. M. Tusi, R. M. Piasentin, M. Linardi, E.V. Spinacé, A. O. Neto, Int. J.
Electrochem. Sci., 5 (2010) 39.
7. H. Liu, C. Song, L. Zhang , J. Zhang, H. Wang, D.P. Wilkinson; J. Power Sources 155 (2006) 95.
8. W. M. Martínez, T. T. Thompson, M. A. Smit, Int. J. Electrochem. Sci., 5 (2010) 931.
9. A. Hamnett; Catal. Today 38 (1997) 445.
10. J.L. Go´mez de la Fuente, M.V. Martı´nez-Huerta, S. Rojas, P. Terreros, J.L.G. Fierro, M.A. Pena;
Catal. Today 116 (2006) 442.
11. E.A. Bagotski, Y.B. Vassiliev, O.A. Khazova, J. Electroanal. Chem. 81 (1977) 229.
12. G. Stalnionis , L. Tamasauskaite-Tamasiunaite , V. Pautieniene , A. Sudavicius, Z. Jusys, J. Solid
State Electrochem. 8 (2004) 892.
13. B. Gurau, R.Viswanathan, R.Liu, T.J. Lafrenz, K.L. Ley, and E. S. Smotkin, E.Reddington,
A.Sapienza, B.C. Chan, T.E. Mallouk, S. Sarangapani, J. Phys. Chem. B 102(1998) 9997.
14. Z. Liu, J.Y. Lee, W. Chen, M. Han, L.M. Gan, Langmuir 20(2004) 181.
15. T. Maiyalagan Int. J. Hyd. Energy. 34 (2009) 2874.
16. T. Maiyalagan, J Solid State Electrochem 13 (2009) 1561.
17. S. Jingyu, H. Tianshu, C. Yanxia, Z. Xiaogang, Int. J. Electrochem. Sci. 2 (2007) 64.
18. A.O. Neto, R.R. Dias, M.M. Tusi , M. Linardi, E.V. Spinacé, J. Power Sources 166(2007) 87.