This user manual provides instructions for operating a Pelican jamming system model CT-6067. It outputs between 15-100W on each of six frequency bands between 1570-1620MHz, 2400-2500MHz, 433MHz, 5700-5900MHz, 865-920MHz, and 1220-1260MHz. Safety guidelines warn to follow all instructions, handle it carefully due to heat dissipation, and only allow qualified service. It features omni-directional antennas, power input from 110V or 220V AC, and LED indicators of conditions. Quick installation involves connecting corresponding antennas to channels and turning the main power and each band power to maximum output. An external battery can also power the jam

1. 1
User manual
CT-6067 Series
Pelican jamming system

2. 2
Foreword
This manual is the operating instructions of the CT-6067 Series Jammer (referred to as the
“unit” in this manual). The unit outputs 15-100W for each of the 6 bands 1570-1620MHz,
2400-2500MHz, 433MHz, 5700-5900MHz, 865-920MHz, 1220-1260MHz
Safety guidelines
Read the following guidelines before using the unit. Failure to comply with these
guidelines may be dangerous or illegal. In any event of doubt, consult your local
distributor or Vendor’s support staff before use.
Handling and transportation
Take maximum care while handling the unit.
Environmental conditions
Do not place the unit near heat sources. The unit dissipates a lot of heat. Never
block its ventilation holes and do not insert any objects through them. Always
allow at least 10 cm clearance in front of ventilation holes on two sides for free air
circulation
Qualified service
Only trained service personnel qualified by Vendor are allowed to diagnose and maintain
the unit in accordance with established safety practices and standards.
Features
 Jamming frequency
 CH1: 1570MHz-1620MHz 100W
 CH2: 24000MHz-2500MHz 100W
 CH3: 433MHz 100W
 CH4: 5700MHz – 5900MHz 15W
 CH5: 860MHz – 920MHz:100W
 CH6: 1220MHz – 1260MHz :100W
 The unit has output power for 100W for each of Five bands and 5.8GHz is 15W
 Omni antennas (3-8dBi).

3. 3
 The Conditions in the system are indicated by the LEDs.
 The input power applied from 110V or 220V AC.
General Description
6 Omni
Antnnas
Power
Adapter
Antenna’s Cable
Main Power Switch
AC 110-240V
Power
Cable
Power Switch
All Dins Down…Max
Output Power
AC Power Adaper
External Battery

4. 4
Quick Installation:
Step 1:
Connect all antennas to the Same CH Bands…CH1 to CH1….
***NOTE***:
Before you turn on the jammer, please………..
Make sure connect all Antennas to the jammer
CH6: GPS L2 MHz
CH2: 2400MHz
CH5: 868MHz
CH3: 433MHzCH4: 5800MHz
CH1: GPS L1 MHz
CH1: 1575MHz
CH2: 2400MHz
CH3: 433MHz
CH4: 5800MHz
CH5: 868MHz
CH6: 1220MHz

5. 5
Step 2:
Turn “ Main Power” ON
Step 3:
Turn Each Band “ ON “…….
Step 4:
Turn Each Band Output Power to MAX… ALL Dins DOWN to MAX.
Step 2:
Switch ON
on Main Power after you
connect all Antennas to
the Jammer
Step 3:
Switch ON Each Band
Power Switch
All Dins Down…Max
Output Power

6. 6
External Battery Options: B-50AH
Connect to JammerAC 220V Power
Cord for Charging
Battery LED StatusMain Siwtch
Battery AH Left
Estimated Working
Time Left
Battery AH Percent
Left
Current Battery Vlotage The Jammer work
Current Amp