This report discusses the development of a drone concept for wildlife observation. Two design alternatives were developed and evaluated using decision matrices and prototype testing. The second alternative was selected for its better aerodynamics and lift-to-drag ratio. A prototype of the second design was built and launch tested, with results showing discrepancies from modeled predictions likely due to modeling assumptions. The team developed requirements, evaluated designs, built and tested a prototype to create a drone concept for wildlife photography.
A pitonisa prevê que um famoso morrerá no próximo ano, o terrorismo continuará e a crise econômica piorará, mas Lula não irá para a cadeia. O cliente pergunta se há alguma novidade além dessas previsões negativas.
Este documento ofrece lecciones aprendidas a lo largo de un largo camino. Enseña que no basta con mirar o escuchar para ver u oír verdaderamente. Aprendió que caminar solo no es soledad y que la cobardía no es paz. Aunque la vida es breve, el amor puede florecer y marchitarse como una flor. La humildad no es sumisión sino servir a los demás. Cuando las cosas van mal, no hay que desistir sino insistir más. Los amigos brindan abrigo, refugio, esperanza y
Hillsborough County Fire Rescue is requesting $50,000 from The Leary Firefighters Foundation to support their Youth Opportunity Program. The grant would help fund the construction of a new training facility to provide free firefighter training to candidates from low-income communities. This is necessary because the current costs of firefighter training through colleges prevents many from underprivileged backgrounds from entering the profession. The program aims to recruit and train candidates to help address staffing needs and improve diversity within Hillsborough County Fire Rescue to better serve their diverse population.
This document describes the design and development of a hexa-copter (six rotor drone) called the KU-COPTER for environmental research applications. It discusses how the design of the hexa-copter frame was based on the logo of Kathmandu University, and various materials for the frame like aluminum composite panel and PVC foam were considered through simulations to optimize strength and weight. The developed hexa-copter is intended to enable applications like aerial surveillance, photogrammetry, and delivery for environmental research while being a low-cost alternative to manned aircrafts.
A pitonisa prevê que um famoso morrerá no próximo ano, o terrorismo continuará e a crise econômica piorará, mas Lula não irá para a cadeia. O cliente pergunta se há alguma novidade além dessas previsões negativas.
Este documento ofrece lecciones aprendidas a lo largo de un largo camino. Enseña que no basta con mirar o escuchar para ver u oír verdaderamente. Aprendió que caminar solo no es soledad y que la cobardía no es paz. Aunque la vida es breve, el amor puede florecer y marchitarse como una flor. La humildad no es sumisión sino servir a los demás. Cuando las cosas van mal, no hay que desistir sino insistir más. Los amigos brindan abrigo, refugio, esperanza y
Hillsborough County Fire Rescue is requesting $50,000 from The Leary Firefighters Foundation to support their Youth Opportunity Program. The grant would help fund the construction of a new training facility to provide free firefighter training to candidates from low-income communities. This is necessary because the current costs of firefighter training through colleges prevents many from underprivileged backgrounds from entering the profession. The program aims to recruit and train candidates to help address staffing needs and improve diversity within Hillsborough County Fire Rescue to better serve their diverse population.
This document describes the design and development of a hexa-copter (six rotor drone) called the KU-COPTER for environmental research applications. It discusses how the design of the hexa-copter frame was based on the logo of Kathmandu University, and various materials for the frame like aluminum composite panel and PVC foam were considered through simulations to optimize strength and weight. The developed hexa-copter is intended to enable applications like aerial surveillance, photogrammetry, and delivery for environmental research while being a low-cost alternative to manned aircrafts.
- AERONAUTIC OPTICS - A Proposal to Build...Erin Winkler
This proposal outlines a plan to design and build a drone equipped with a high-quality camera to analyze landslide risk in communities around Guatemala City. A team of students will design a drone that can take aerial photos to be compiled into 3D images and analyzed using software programs to map terrain and slope for landslide assessment. The drone aims to provide clear photos from high elevations and hazardous areas to help warn communities of risks and prevent loss of life from landslides.
The document describes Rutgers University's entry for the AUVSI SUAS competition. It summarizes the team's goals of meeting all threshold requirements and as many objective requirements as possible. The team chose to continue using its successful Skywalker X8 airframe design. Key systems include the 3DR Pixhawk autopilot, Canon T2i camera, and Intel NUC onboard computer. Extensive testing was performed on individual subsystems and an overall competition run-through. The team expects to meet all threshold tasks and many objective tasks through autonomous flight, search area coverage, and target recognition capabilities.
The document summarizes a company called Vantage Robotics that is developing an easy-to-use, safe, and portable drone called Snap. Snap competes in the $2.4 billion consumer drone market and has the potential to capture part of the $3.7 billion commercial drone market due to an FAA waiver allowing its use near people. Snap is lightweight, durable, has extended flight times through optional modules, and its safety features enable greater autonomy and new types of shots. The company is pursuing multiple revenue streams including hardware sales, commercial services, and software/content and has received strong pre-order demand. Vantage believes Snap is defensible due to its user-generated flight paths and modular ecosystem.
The document discusses drone delivery and its potential to disrupt last-mile delivery. It provides an overview of drone technology, including different types of drones, specifications, generations of delivery drones, and current players in the drone delivery market such as Amazon. Drone delivery can significantly reduce delivery times and costs while helping the environment by reducing emissions compared to conventional delivery vehicles. It also discusses how drone delivery is being used to save lives by delivering medical supplies in some parts of the world.
Drones are unmanned aerial vehicles that are made from lightweight composite materials and controlled remotely. They consist of two main parts - the drone itself and the ground control system. Drones can be equipped with cameras, sensors and other equipment. They come in various shapes and sizes and can be launched by hand or from ground stations. Common applications of drones include surveillance, inspections, aerial photography, search and rescue operations, and scientific research. Drone technology is constantly evolving with new innovations bringing more advanced drones to the market regularly.
This document proposes a drone-based system for inspecting bridges using 3D printed components. It describes a landing gear system that allows drones to perch on bridge structures for extended inspection times. Rotor shields are also designed to protect drones from collisions. Carbon fiber materials printed on a Markforged printer are used for strength and lightweighting. ABS shields printed on a Makerbot can be cheaply replaced if damaged. Financial analysis estimates the system could capture 0.5-1.5% of the $7.5 billion annual bridge inspection market in 5 years, yielding over $3 million in annual profits.
The document provides details on redesigning a gopher tortoise scoping system. It discusses:
1) Requirements for the redesign including making the system smaller, more maneuverable, able to capture video/photos, and withstand weather.
2) Design objectives like withstanding temperatures from 0-100°F, fitting in a backpack under 50 lbs, and navigating small 4-6 inch burrows.
3) Exploration of design options including using a Raspberry Pi, gamepad, camera, battery, motors, and enclosure to make a portable, durable system that improves on previous designs.
Drone Systems and Airframe Selection - Scope and OptionsColin Snow
Presentation to 2016 Commercial UAV Expo: SCOPE & OPTIONS FOR SPECIFIC PROJECTS
Knowing the reasons you want to implement a new technology and ensuring it’s achievable have a huge bearing on its success or failure. If business benefits are not realized, or budgets are busted, the project has failed. So if you are considering acquiring or incorporating an unmanned aircraft system for your business, it pays to be prepared. In this session we’ll cover the five most important things to consider when adopting drones for your business.
This document summarizes a research paper on drone delivery systems. It discusses how online shopping and delivery is increasingly relying on fast doorstep delivery. Drone delivery could allow for accelerated delivery times, improved accuracy, and reduced human costs compared to traditional delivery methods. The system is designed using a Naza M-lite flight controller, ESC (electronic speed controller), and GPS module. It then reviews related work on using drones for medical supply delivery in disaster relief situations and for agricultural purposes like plant protection.
This document summarizes the design and testing of an unmanned aerial vehicle (UAV) built by students to survey farmland by taking aerial images and recording GPS coordinates. The students followed an engineering design process, beginning with brainstorming how to survey large areas of rough terrain. They researched UAV types and flight principles and designed a flying wing platform suited for autonomous flight, first-person viewing, and ease of use. A quality function deployment analysis supported this design. The UAV was constructed of expanded polypropylene foam and tested through several flights. High definition video and images captured during test flights over a banana crop provided a valuable aerial view for monitoring the farm.
AIRCRAFT DESIGN PROJECT -I FIGHTER JETS A PROJECT REPORTDon Dooley
This document provides an overview of the design process for a fighter jet aircraft project. It includes acknowledgements, an abstract, table of contents, and sections on introduction to design, aircraft introduction, comparative details and graphs, weight estimation, airfoil and wing selection, tail plane, landing gear, power plant selection, drag estimation, V-N diagram, 3 view diagram, final parameters, and conclusion. The project involves students conceptualizing and designing a fighter jet to meet performance specifications while allowing for weapon carriage, efficiency, and reduced emissions.
Rapid Development of a Rotorcraft UAV System - AHS Tech Specialists Meeting 2005Mark Hardesty
This document summarizes the development of a rotorcraft unmanned aerial vehicle (UAV) system by Boeing Phantom Works over less than one year. They selected the MD 530F helicopter due to its performance capabilities and military counterpart. The design integrated commercial off-the-shelf hardware and proprietary Boeing flight control software. Bench and flight testing were prioritized to rapidly expand the flight envelope from initial engagement of the electrical flight controls to autonomous takeoffs, landings and navigation. The manual override capability allowed high-risk prototype systems to be safely tested.
This document provides details of an aircraft design project for a new personal jet called "The Flash" being designed by Kent Aerospace. It includes sections on requirements analysis, technical design, manufacturing plan, regulatory compliance, program management, finance, marketing, and socioeconomic impacts. The technical design section provides details on sizing methodology, assumptions, wing and tail geometry, thrust-to-weight ratio, powerplant specifications, wing loading data, and performance results. The design utilizes twin DGEN 380 turbofan engines from Price Induction and is intended to carry 3 passengers up to 800 nautical miles at a cruise speed of 230 knots.
The document describes the design and fabrication of a small-scale radio controlled unmanned aerial vehicle (UAV) for aerial photography. Key aspects of the project include:
1) The UAV will be constructed primarily of balsa wood with a wingspan of 120cm and powered by an 820kv brushless motor and 3-cell lithium polymer battery.
2) Aerodynamic and structural design calculations were performed to determine dimensions, required thrust and power, stall speed, and glide range.
3) The design and fabrication process will involve selecting an airfoil, creating CAD models, building the wing ribs and spars, assembling the fuselage, and installing electronic components before flight testing
This document discusses the need for and advantages of parachute recovery systems (PRS) for unmanned aerial systems (UAS). It begins by summarizing the company's history of developing PRS for rocketry and then expanding to UAS customers. The document then outlines several drivers for PRS adoption, including safety regulations, insurance requirements, and failure mitigation costs. It proceeds to describe different parachute designs and their characteristics. Finally, it discusses challenges to wider PRS adoption and opportunities for further standardization and integration with UAS.
The document provides information about Skylark Aerial Photography, a business that uses drones to provide aerial imagery services. It discusses Simon Handley's background as the owner, the types of drones used including quadcopters and fixed wing models, and the commercial services offered, which include aerial photography, inspections, surveys, and video/film work. Regulations for drone operation are also summarized, including licensing requirements from the CAA. Examples of assignments are shown to demonstrate the business' work.
ANALYSING AND MINIMIZATION OF SONIC BOOM IN SUPERSONIC COMMERCIAL AIRCRAFTIRJET Journal
This document discusses the analysis and minimization of sonic booms for a supersonic commercial aircraft. It describes calculating aerodynamic and structural properties of the aircraft, as well as modeling the aircraft in CATIA and performing computational fluid dynamics analysis in ANSYS Fluent. The document summarizes methods for approximating the sonic boom using Carlson theory and Sea Bass. It aims to design an aircraft that can achieve a cruise speed of Mach 1.6 over 4600km with a sonic boom overpressure of 0.547 psf and duration of 0.3 seconds.
Drone photography has revolutionized the field by allowing photographers to capture images from new perspectives. Drones provide affordable aerial photography and have been adopted by many industries like real estate, filmmaking, journalism, and environmental conservation. Some benefits of drone photography include unique angles, accessibility, efficiency, and safety. However, photographers must consider regulations, weather, battery life, and ethics when using drones. Aspiring drone photographers should learn regulations, practice in open spaces, and focus on composition.
- AERONAUTIC OPTICS - A Proposal to Build...Erin Winkler
This proposal outlines a plan to design and build a drone equipped with a high-quality camera to analyze landslide risk in communities around Guatemala City. A team of students will design a drone that can take aerial photos to be compiled into 3D images and analyzed using software programs to map terrain and slope for landslide assessment. The drone aims to provide clear photos from high elevations and hazardous areas to help warn communities of risks and prevent loss of life from landslides.
The document describes Rutgers University's entry for the AUVSI SUAS competition. It summarizes the team's goals of meeting all threshold requirements and as many objective requirements as possible. The team chose to continue using its successful Skywalker X8 airframe design. Key systems include the 3DR Pixhawk autopilot, Canon T2i camera, and Intel NUC onboard computer. Extensive testing was performed on individual subsystems and an overall competition run-through. The team expects to meet all threshold tasks and many objective tasks through autonomous flight, search area coverage, and target recognition capabilities.
The document summarizes a company called Vantage Robotics that is developing an easy-to-use, safe, and portable drone called Snap. Snap competes in the $2.4 billion consumer drone market and has the potential to capture part of the $3.7 billion commercial drone market due to an FAA waiver allowing its use near people. Snap is lightweight, durable, has extended flight times through optional modules, and its safety features enable greater autonomy and new types of shots. The company is pursuing multiple revenue streams including hardware sales, commercial services, and software/content and has received strong pre-order demand. Vantage believes Snap is defensible due to its user-generated flight paths and modular ecosystem.
The document discusses drone delivery and its potential to disrupt last-mile delivery. It provides an overview of drone technology, including different types of drones, specifications, generations of delivery drones, and current players in the drone delivery market such as Amazon. Drone delivery can significantly reduce delivery times and costs while helping the environment by reducing emissions compared to conventional delivery vehicles. It also discusses how drone delivery is being used to save lives by delivering medical supplies in some parts of the world.
Drones are unmanned aerial vehicles that are made from lightweight composite materials and controlled remotely. They consist of two main parts - the drone itself and the ground control system. Drones can be equipped with cameras, sensors and other equipment. They come in various shapes and sizes and can be launched by hand or from ground stations. Common applications of drones include surveillance, inspections, aerial photography, search and rescue operations, and scientific research. Drone technology is constantly evolving with new innovations bringing more advanced drones to the market regularly.
This document proposes a drone-based system for inspecting bridges using 3D printed components. It describes a landing gear system that allows drones to perch on bridge structures for extended inspection times. Rotor shields are also designed to protect drones from collisions. Carbon fiber materials printed on a Markforged printer are used for strength and lightweighting. ABS shields printed on a Makerbot can be cheaply replaced if damaged. Financial analysis estimates the system could capture 0.5-1.5% of the $7.5 billion annual bridge inspection market in 5 years, yielding over $3 million in annual profits.
The document provides details on redesigning a gopher tortoise scoping system. It discusses:
1) Requirements for the redesign including making the system smaller, more maneuverable, able to capture video/photos, and withstand weather.
2) Design objectives like withstanding temperatures from 0-100°F, fitting in a backpack under 50 lbs, and navigating small 4-6 inch burrows.
3) Exploration of design options including using a Raspberry Pi, gamepad, camera, battery, motors, and enclosure to make a portable, durable system that improves on previous designs.
Drone Systems and Airframe Selection - Scope and OptionsColin Snow
Presentation to 2016 Commercial UAV Expo: SCOPE & OPTIONS FOR SPECIFIC PROJECTS
Knowing the reasons you want to implement a new technology and ensuring it’s achievable have a huge bearing on its success or failure. If business benefits are not realized, or budgets are busted, the project has failed. So if you are considering acquiring or incorporating an unmanned aircraft system for your business, it pays to be prepared. In this session we’ll cover the five most important things to consider when adopting drones for your business.
This document summarizes a research paper on drone delivery systems. It discusses how online shopping and delivery is increasingly relying on fast doorstep delivery. Drone delivery could allow for accelerated delivery times, improved accuracy, and reduced human costs compared to traditional delivery methods. The system is designed using a Naza M-lite flight controller, ESC (electronic speed controller), and GPS module. It then reviews related work on using drones for medical supply delivery in disaster relief situations and for agricultural purposes like plant protection.
This document summarizes the design and testing of an unmanned aerial vehicle (UAV) built by students to survey farmland by taking aerial images and recording GPS coordinates. The students followed an engineering design process, beginning with brainstorming how to survey large areas of rough terrain. They researched UAV types and flight principles and designed a flying wing platform suited for autonomous flight, first-person viewing, and ease of use. A quality function deployment analysis supported this design. The UAV was constructed of expanded polypropylene foam and tested through several flights. High definition video and images captured during test flights over a banana crop provided a valuable aerial view for monitoring the farm.
AIRCRAFT DESIGN PROJECT -I FIGHTER JETS A PROJECT REPORTDon Dooley
This document provides an overview of the design process for a fighter jet aircraft project. It includes acknowledgements, an abstract, table of contents, and sections on introduction to design, aircraft introduction, comparative details and graphs, weight estimation, airfoil and wing selection, tail plane, landing gear, power plant selection, drag estimation, V-N diagram, 3 view diagram, final parameters, and conclusion. The project involves students conceptualizing and designing a fighter jet to meet performance specifications while allowing for weapon carriage, efficiency, and reduced emissions.
Rapid Development of a Rotorcraft UAV System - AHS Tech Specialists Meeting 2005Mark Hardesty
This document summarizes the development of a rotorcraft unmanned aerial vehicle (UAV) system by Boeing Phantom Works over less than one year. They selected the MD 530F helicopter due to its performance capabilities and military counterpart. The design integrated commercial off-the-shelf hardware and proprietary Boeing flight control software. Bench and flight testing were prioritized to rapidly expand the flight envelope from initial engagement of the electrical flight controls to autonomous takeoffs, landings and navigation. The manual override capability allowed high-risk prototype systems to be safely tested.
This document provides details of an aircraft design project for a new personal jet called "The Flash" being designed by Kent Aerospace. It includes sections on requirements analysis, technical design, manufacturing plan, regulatory compliance, program management, finance, marketing, and socioeconomic impacts. The technical design section provides details on sizing methodology, assumptions, wing and tail geometry, thrust-to-weight ratio, powerplant specifications, wing loading data, and performance results. The design utilizes twin DGEN 380 turbofan engines from Price Induction and is intended to carry 3 passengers up to 800 nautical miles at a cruise speed of 230 knots.
The document describes the design and fabrication of a small-scale radio controlled unmanned aerial vehicle (UAV) for aerial photography. Key aspects of the project include:
1) The UAV will be constructed primarily of balsa wood with a wingspan of 120cm and powered by an 820kv brushless motor and 3-cell lithium polymer battery.
2) Aerodynamic and structural design calculations were performed to determine dimensions, required thrust and power, stall speed, and glide range.
3) The design and fabrication process will involve selecting an airfoil, creating CAD models, building the wing ribs and spars, assembling the fuselage, and installing electronic components before flight testing
This document discusses the need for and advantages of parachute recovery systems (PRS) for unmanned aerial systems (UAS). It begins by summarizing the company's history of developing PRS for rocketry and then expanding to UAS customers. The document then outlines several drivers for PRS adoption, including safety regulations, insurance requirements, and failure mitigation costs. It proceeds to describe different parachute designs and their characteristics. Finally, it discusses challenges to wider PRS adoption and opportunities for further standardization and integration with UAS.
The document provides information about Skylark Aerial Photography, a business that uses drones to provide aerial imagery services. It discusses Simon Handley's background as the owner, the types of drones used including quadcopters and fixed wing models, and the commercial services offered, which include aerial photography, inspections, surveys, and video/film work. Regulations for drone operation are also summarized, including licensing requirements from the CAA. Examples of assignments are shown to demonstrate the business' work.
ANALYSING AND MINIMIZATION OF SONIC BOOM IN SUPERSONIC COMMERCIAL AIRCRAFTIRJET Journal
This document discusses the analysis and minimization of sonic booms for a supersonic commercial aircraft. It describes calculating aerodynamic and structural properties of the aircraft, as well as modeling the aircraft in CATIA and performing computational fluid dynamics analysis in ANSYS Fluent. The document summarizes methods for approximating the sonic boom using Carlson theory and Sea Bass. It aims to design an aircraft that can achieve a cruise speed of Mach 1.6 over 4600km with a sonic boom overpressure of 0.547 psf and duration of 0.3 seconds.
Drone photography has revolutionized the field by allowing photographers to capture images from new perspectives. Drones provide affordable aerial photography and have been adopted by many industries like real estate, filmmaking, journalism, and environmental conservation. Some benefits of drone photography include unique angles, accessibility, efficiency, and safety. However, photographers must consider regulations, weather, battery life, and ethics when using drones. Aspiring drone photographers should learn regulations, practice in open spaces, and focus on composition.
1. DPC Final Report
Team One
A. Whittle, P. Achari, S. Moseley, J. Halper, E. McCarty, and C. Hunt,
ENGE 1216
May 5, 2016
2. Executive Summary:
This report discusses the development and selection of a drone concept that has the intended
purpose of wildlife observation, photography, and filmography. Current models on the market
are expensive, heavy, and noisy, and our solution is meant to address such problems.
In order to develop a successful concept for our drone, we first had to define criteria, constraints,
and a use case scenario. We decided that the drone should be quiet, compact, lightweight, be
capable of carrying a camera, and be able to fly above 100 ft. We chose these criteria and
constraints based on an interest in ease of use for the consumer and to avoid disturbing wildlife
and natural ecosystems. The drone is intended for wildlife observation, photography, and
filmography by amateur and professional wildlife photographers and is designed to disturb the
environment as little as possible.
Our team developed two different design alternatives to choose from. The viability of each
alternative was determined via decision matrices in which we weighed the importance of the
following criteria: aesthetics, weight, aerodynamics, time of flight, max height, size, cost, and lift
to drag ratio, and scored each alternative accordingly. We also built prototypes of the two
alternatives and glide tested them from various heights under controlled conditions. We decided
that the second alternative was the better option in accordance with our objectives based on the
results from the decision matrices and the prototype glide test results.
After choosing the better alternative, we developed a second prototype of the design. We also
created a MATLAB synthesis code to model the prototype’s trajectory after launch based on
assumptions about the prototype, launch mechanism, and launch environment, excluding the
mass prototype, which is a user-inputted value. To test the performance of this prototype, we
launched it out of a tube using pressurized water and recorded its angle of trajectory, flight
distance, and maximum height of flight. We also recorded pressure of the water, the amount of
water used for launch, and the wind speed at the date and time of launch. After launch testing the
prototype, we found that our test results did not match our synthesis code results. This
discrepancy can be attributed to the differences between the assumed values for variables in the
synthesis code and reality.
During this design project, our team developed designs for a wildlife photography drone. We
chose which design to use based on decision matrix values and prototype glide test results and
we used this design to develop a prototype for launch testing. After comparing our test results
with our synthesis code results, we found that they did not match, which was a result of certain
assumptions and limitations in the synthesis code.
Table of Contents
I. Introduction
3. II. Use Case/Requirements
A. Table 1
III. Ethics
IV. Design Alternatives
A. Figure 1
B. Figure 2
V. Design Evaluation
A. Table 2
B. Table 3
C. Figure 3
VI. Prediction and Testing
A. Figure 4
B. Figure 5
C. Figure 6.0
D. Figure 6.1
E. Table 4
F. Figure 7
VII. Conclusion
VIII. Limitations and Future Plans
IX. References
X. Appendices
A. Appendix A
B. Appendix B
C. Appendix C
D. Appendix D
E. Appendix E
F. Appendix F
G. Appendix G
I. Introduction
Drones are becoming increasingly popular in today’s society. They can be used to conduct many
different operations, ranging from surveillance to package delivery. Each new drone that comes
on the market is competing to be the best in its field, and shows improvements upon previous
4. models. The drone has become progressively more technologically advanced, with an emphasis
in capturing pictures and films.
During this project, our design team developed a drone production concept (DPC) that would be
used to photograph and film wildlife in various environments. The drone will be a low cost, high
performing, and mobile competitor compared to other observer drones in the field. Two different
concepts were used to decide what features to implement in the DPC design. Through prototype
testing, research, and the development of a decision matrix, the second concept was determined
be the option that best fit our criteria, constraints, and use case scenario. Through more testing,
synthesis code development, and prototype launches, our team was able to successfully develop
our DPC.
Drones have a variety of different uses. For example, unmanned aircrafts that can be controlled
from the ground are incredibly useful in search and rescue operations, as these machines can
record events happening in dangerous situations and relay a live feed to the proper authorities,
enabling them to take action. Drones can also be used to deliver packages, as surveillance
machines for public or private use, or as a security measure for any member of the public.
Drones can also be used in aerial photography and filmography, however there are certain
drawbacks and limitations to this if one’s intention is capturing images of wildlife in nature.
These shortcomings have encouraged our design team to develop and produce a drone that can
capture high definition footage and photographs of wildlife from the air.
II. Use Case/Requirements
Our team is a small technology startup company that has designed a drone production concept
with the target demographic of professional and amateur photographers/filmographers. The
drone will specialize in observing wildlife located in potentially dangerous terrain or sensitive
ecosystems such as forests, isolated mountains, and glaciers. Modern observer drones implement
high-quality cameras and are composed of aerodynamic materials in order to ensure their
success, however these products cost approximately $1400 and their average battery life is
approximately 28 minutes [1]. Furthermore, drones are known to emit noises loud enough to
disturb its surrounding environment. There are solutions being developed with the aim of cutting
down on noise emissions, such as reducing the amount of propellers or employing several small
motors instead of one large one, however this is still an issue in the drone market [2]. High cost
and high noise emission are examples of features that we would like to improve upon in
constructing our drone, as these design changes would allow our product to be more practical for
consumers. There are several parties that could be affected by the production and success of our
drone, including company employees, drone manufacturers, investors, consumers, and
consumers’ clients, which may include wildlife magazines, movie producers, and advertisers.
Our DPC is less than 10 inches in diameter and less than 30 inches in total length, as seen in
Figure 1. These size constraints were created to ensure that the drone will be large enough to
support a camera and all of its inner components, while being small enough to foster easy
mobility. Although our length constraint is 30 inches, we expect the drone to be much shorter to
allow for even easier mobility. Most drones that implement cameras are quadcopters as opposed
to our airplane-like drone design. When being transported, quadcopters must be kept in their
boxes to avoid damage, so we aimed for a design that is lightweight and compact so it can be
5. easily carried. The drone’s tube-like structure and folding wings will allow it to easily fit into a
bag while remaining intact. The bag can then be carried to the desired destination and the drone
can be launched by gently throwing it like a model airplane.
The DPC’s weight should be less than 3 pounds to also allow for easier mobility and
maneuverability. The drone must be easy to carry and alleviate as much work for the user as
possible. We chose a constraint of 3 pounds, as our competitor, the Phantom 4, is 3.04
pounds[1]. Although a small difference, this lighter weight will give our drone an edge over the
Phantom 4 and other competitors. A lighter weight will also improve the lift upon drag ratio.
Since weight is the force a gravity, as the mass increases the force of gravity on the DPC would
also increase. The only force counteracting the weight is lift. This means weight and lift and
directly proportional; if weight goes up, so does the lift needed to keep it in the air. [3]
Table 1: Criteria and Constraints
In order for our DPC to be useful to our consumers, our team had to define important flight
requirements. Our drone must be able to maneuver around obstacles, such as trees and hills, in
different situations, so we decided that the drone must be able to reach a height of at least 100 ft.
Ideally our drone will be able to fly higher than this in order to provide more space to maneuver
around tall objects, and to allow enough time to locate and record footage of surrounding
wildlife. Another concern is the drone’s time of flight. As previously stated, the Phantom 4 can
maintain an air time of 28 minutes. We would like our drone to maintain an airtime of at least an
hour, over twice that of the Phantom 4. This extra time will give the user a longer period of
uninterrupted filming.
In addition to size, weight, and flight guidelines, we also considered the drone’s retail and
manufacturing cost. A high quality drone for commercial use can cost over $1000, retail; the
Phantom 4 costs $1400, retail. The materials chosen for our DPC cost a total $578. We
determined we would use a magnesium structure similar to the Phantom 4 and an aluminum
composite body to ensure a durable, lightweight product. [4][5]. Our solution includes the
implementation of a GoPro, which would provide the drone with the same quality camera as that
on the Phantom 4, but at a much cheaper price of $500 per camera [6]. Overall, with the
inclusion of labor and design, our price point for the DPC will be $900 which is lower than our
target price of $1000 as seen in Figure 1.
6. Our drone requires a propulsion system to keep our it in the air and to provide extra lift. The
propulsion system will be electronic and will be able to be recharged after each use. We will also
develop an app based controlling system, similar to that of the Phantom 4, instead of a remote to
cut down on material and manufacturing costs. The app will come free with the purchase of the
DPC.
III. Ethics
In regards to the ethics of our drone, several issues must be addressed. The drone is meant to fly
high above the land it is surveying, which brings up the issue of privacy infringement. The
camera could capture feed of civilians without their knowledge while in the air, which is could
be considered an invasion of privacy, but this cannot necessarily be controlled; campers and
hikers are at most risk of this happening. Another possible issue arises with the idea of
trespassing. These drones could potentially be used to survey and gain information on restricted
properties, which is definitely not one of its intended purposes. Furthermore, studies show that
the heart rates of animals such as bears and penguins spike drastically when a drone flies by
overhead. "The magnitude of some of the heart-rate spikes were shocking," says Mark Ditmer, a
wildlife ecologist at the University of Minnesota. “To see heart rates go from 41 beats per minute
prior to the unmanned aerial vehicles' flight to over 160 beats per minute during the flight was
far beyond what we expected[7]." This is not an ideal situation, as we do not want our drone to
scare those which we are trying to observe. The discovery of a species in a specific area could
also include ethical issues; this could lead to invasive human presence in sensitive environments,
which would impede on the welfare of the affected wildlife. There is no way to avoid all of these
ethical issues, however, we can work diligently to minimize their effects.
IV. DesignAlternatives
In order to decide how to construct our drone, we developed two design alternatives. Our first
DPC, Figure 1, implements short, rectangular wings. The wings tilt downward and are connected
by a thin structure that pierces the 4-inch diameter body. Both the nose and the tail converge at a
point. Most of the weight is located towards the front of the bullet-shaped design. Instead of our
desired teardrop wing shape, we settled for a rectangular design, which ended up being our
closest option. This model lacks stabilizer fins, but does incorporate vertical tailfin. The lack of
this feature, as described by Life Science, will not allow “air to move faster over the top” of the
wing than the bottom of the wing[3]. Ultimately, the lack of stabilizer fins is what caused this
model to fail. The vertical fin located at the back does little to stabilize our model, as the model
is not heavy enough for the center of mass to be located under the center of the wings, which is
necessary in a design without stabilizer. Additionally, the durability of this alternative was poor
and its wings had a tendency to bend at undesirable angles.
7. Figure 1: Design concept #1
Our second concept, Figure 2, incorporates distinct, more desirable features. Instead of
possessing two wings that penetrate the fuselage, there is a single, large wing attached to the top
of the drone. The body of the drone is connected to the tail by a narrow section and the tail is
equipped with a tailfin and stabilizers. The purpose of the stabilizers is to “provide stability for
the aircraft, to keep it flying straight,” and to prevent an “up-and-down, or pitching, motion of
the aircraft nose” [8]. The designs’s sleek body and long wings are an improvement upon the
bulky body and choppy wings of the first alternative. This model exhibited improved lift,
stability, and durability compared to our first concept.
Figure 2: Design concept #2
Several different materials, many household, were used in the construction of our low-fidelity
DPC prototypes. Assembling the prototypes was fairly simple with some trial and error.
Although the two different concepts seem similar in design, the only features that these two
alternatives share are the tailfin, the propulsion system, and the camera. The camera is located at
the bottom of the body and is positioned downward to help capture photographs of the wildlife at
hand.
8. V. DesignEvaluation
After we developed two alternatives for our DPC, we evaluated each concept individually. We
did this by testing the lift to drag ratio (L/D) of each alternative by glide testing each prototype
from different heights in a controlled environment and recording the horizontal distance of each
throw. Then the L/D ratio was then calculated using the mass of the prototype along with the
throw distance. This gave us an approximation of the L/D ratio which helped us determine which
alternative performed better. The results from these glide tests can be seen in Table 2 below.
Table 2: Prototype Testing Results
In addition to prototype glide testing, we also used decision matrices, see Table 3, to help us
determine the preferred alternative for our DPC. In the first step of our concept selection, we
rated our established criteria against one another. We decided that certain criteria were more
important than others in our design. Our criteria, in order of decreasing importance, are: lift to
drag ratio, aerodynamics, time of flight, size, weight, maximum height, cost, and aesthetic.
These criteria were rated as such because it is essential that the performance of the plane is the
most important factor in our design. Lift to drag ratio is essential to the performance of the plane
which is why it carries the most weight in our decision matrix. Half our criteria were rated on a
scale of 1 to 10 and were objective criteria. Objective criteria included: aesthetics, aerodynamics,
size, and cost, and could not be quantified under the circumstances of developing the decision
matrices. We did not include time of flight and max height in our concept selection because they
could not be recorded in our testing exercise. The weight was rated on a scale of .001-1 pounds.
This was decided because it was determined that a 1 pound concept would be ideal. Lift to drag
ratio had been rated on a 1-40 ratio. This was determined because it was discovered in our
research that some planes get up to 40 on there L/D ratio.
9. After we scored each of our criteria on their corresponding scales, each score was normalized
against the highest and lowest values of its grading scale. Then the normalized scores were
weighted and added up. After adding up the weighted scores, we determined that our second
design concept was the more viable option. Since design 2 was the most viable option, we
decided to base out DPC off of it. As you can see in Figure 3, we kept the wings on top, and
horizontal and vertical stabilizers just as concept 2 had them.
Table 3- Decision Matrix
Figure 3: Concept 2 DPC drawing
VI. Prediction and Testing
10. Before approving our DPC, it was necessary to create a higher fidelity prototype of our design.
We constructed the DPC with our constraints, criteria, and use case scenario in mind. Our DPC
had to be less than 3 pounds, less than 30 inches long, less than 10 inches in diameter, be able to
fly higher than 100 feet, and have a flight time above an hour. The implementation of these
guidelines can be seen in Figures 4 & 5 . When planning our materials, we had to ensure that the
weight of our prototype was similar to our actual DPC to be able to get an idea of how well it
will perform at that weight. To keep the prototype lightweight, we made the wings out of
styrofoam. Though styrofoam is fairly weak alone, stacking multiple layers of styrofoam on top
of eachother allowed the wings to stay study and light. We also added horizontal and vertical
stabilizers which were also made out of styrofoam to keep our total mass to a minimum. We
attached one AA battery to the nose and one on the bottom of the prototype to shift its overall
center of mass and account for the weight of the motor. The batteries also allowed us to fix the
position of the wings which, in turn, created the best lift to drag ratio.
Figure 4: Top view of prototype concept #2 Figure 5: Side view of prototype concept #2
For our project we programed a synthesis code to approximate the launch of our prototype. This
code had multiple equations that simulated and graphed the results of different aspects of the
launch. The code calculates the vertical position, velocity, pressure, and time of flight of the
prototype with a time interval of .001 seconds. Once the calculations are complete, each array of
information is plotted on a graph relative to the time of flight. Lines 35, 55, 57, and 59, see
Figures 6.0 and 6.1, are lines of code that store each calculation into an array; “p” is the variable
for pressure, “v” for velocity, “y” for horizontal position, and “time” for time of flight. Each of
the following equations use different assumptions made in the beginning to calculate each
variable. Lines 7 - 20 in Figure 6.0 show what each variable stands for and the units of the
variable. This code was useful in that it gave us a model of what our prototype launch might be
like. Because the code is dependent on the empty mass of our prototype, we can predict a
suitable empty mass for our prototype that will generate the best results within the code’s
predetermined conditions. However, there are a number of limitations in the synthesis code.
First, predetermined conditions such as drag, volume of water, and volume of bottle are not
always constant as assumed in the synthesis code. Each bottle (plastic, 2 Liter) is shaped
differently depending on the manufacturer, and therefore prevents the “VT” variable from being
11. the same in all cases. The code is also written for uncommon units of measurement. The values
are in units such as “slugs”, and “feet per seconds squared” put a bit of a mathematical language
barrier between our code and metric users.
Figure 6.0 First half of Synthesis Code
12. Figure 6.1 Second half of synthesis code
Using the simulation from the synthesis code we predicted our prototype would reach a height of
about 100 ft with 300 mL, see Figure 7. After testing, we measured the actual launch height to be
about 42 for the 300ml launch. A few reasons why our test results did not match our prediction
from the synthesis code is because of variables such as wind, drag, and the structure of our
prototype. Within our code there was no wind variable to accommodate for. Therefore, the wind
during our launch, which was calm [9], could have affected the distance, height, and direction
our prototype traveled. The drag ratio in the synthesis code, as previously mentioned, only
accommodates for the body of the prototype. Though the body of the prototype heavily affects
drag variable, the wings, horizontal and vertical stabilizers, and nose of the prototype also
account for the drag value. Because of these additions, the drag value for our prototype was
larger than the drag value generated by the synthesis code. Another reason for the discrepancies
between our prediction and our results was structure of our prototype. The wings on our
prototype were not structurally stable, so when the prototype was launched, the wings were
knocked out of place. The synthesis code could have been modified to produce more realistic
predictions of our launch if we calculated the drag caused by the wings and included a wind
variable. Optimal test conditions would have clear weather with no wind with perfect launch
execution. If there was zero wind, our wings were structurally sound, and we accommodated for
the drag caused by our additions to the body of our prototype, then we could have have,
theoretically, achieved a perfect launch resulting in the same results as predicted.
Table 4: Launch data of prototype
Table 4- Launch
13. Data
Launch
Ml of
Water
Appx. Simulated
Altitude (ft.)
Actual Altitude
(ft.)
Horizontal
Distance (ft.)
1 200 87 18.75 22
2 300 97 40.5 69
3 300 97 45 43
Average 93.66 34.75 44.67
Figure 7. Graph of Predicted Altitude versus Time
VII. Conclusion
Our goal for this design project was to develop a drone product concept that would take high
quality, aerial footage of wildlife and natural environments. Our drones would be smaller,
cheaper, and more versatile than the drones that are currently on the market. Initially we
developed two concepts, one that has square wing design without stabilizers and another that has
a larger, sturdier design with stabilizers. After testing the concepts we decided, with the help of a
decision matrix, that the sturdier, larger wingspan design would fly better than its competing
design. After selection a concept, the design of that concept was translated into a prototype. This
prototype was then tested and it reached average horizontal distance of 45 feet from the launch
site. Overall, the initial selection of our concept and the building of our prototype leads us to
believe that our final product will fly with great performance and credibility.
VIII. Limitations and Future Plans
Our design strategy was limited in a few key ways. Our synthesis code projected our flight
height to be about 100 ft. In reality, this value was only about 34 ft. Our code was inaccurate in
14. predicting the launch data. This code was inaccurate primarily due to the drag coefficient in the
code. This value was set at .0007 and in reality was probably a lot higher. Another limitation of
our code was several uncontrolled variables during the launch. These variables include wind
speed and the weak structure of the prototype. This had a substantial impact on the performance
of the prototype.
In future testing it might be best to incorporate air resistance into the synthesis code. This would
give us a better prediction on the performance of the launch. We might also choose to build our
prototype out of different materials besides plastic bottles and foam board. This would ensure
that the prototype has a strong structure, durable enough for multiple, successful launches. We
could also alter the angle of launch in future tests. This could give us a greater distance on the
launch.
15. XI. References
[1] "DJI Phantom 4", PCMAG, 2016. [Online]. Available:
http://www.pcmag.com/review/342895/dji-phantom-4. [Accessed: 30- Apr- 2016].
[2] D. Hambling, "Silence of the drones: How to quiet that annoying aerial buzz", New Scientist,
2016. [Online]. Available: https://www.newscientist.com/article/dn27696-silence-of-the-drones-
how-to-quiet-that-annoying-aerial-buzz/. [Accessed: 05- May- 2016].
[3] “The Physics of Flight,” Flight. [Online]. Available at:
http://www.lcse.umn.edu/~bruff/bernoulli.html. [Accessed: 05-May-2016].
[4] "Magnesium Metal Ingot, 99.95% Pure, 8 Ounces: Amazon.com: Industrial & Scientific",
Amazon.com, 2016. [Online]. Available: http://www.amazon.com/Magnesium-Metal-Ingot-99-
95-Ounces/dp/B005DPFJJO. [Accessed: 24- Apr- 2016].
[5] A. Gameros, "The Use of Composite Materials in Unmanned Aerial Vehicles (UAVs)",
Azom.com, 2016. [Online]. Available: http://www.azom.com/article.aspx?ArticleID=12234.
[Accessed: 24- Apr- 2016].
[6] H. Black, "GoPro Karma", Shop.gopro.com, 2016. [Online]. Available:
http://shop.gopro.com/hero4/hero4-black/CHDHX-401.html. [Accessed: 30- Apr- 2016].
[7] Charles Q. Choi, “Drones Spook Bears”, Life Science, 2014. [Online].
Available:http://www.livescience.com/51846-drones-spook-bears.html/ [Accessed: 24-Apr-
2016].
[8] N. Hall, Ed., “Horizontal Stabilizer - Elevator,” Horizontal Stabilizer - Elevator, 05-May-
2015. [Online]. Available: https://www.grc.nasa.gov/www/k-12/airplane/elv.html. [Accessed:
04-May-2016].
[9] “Weather History for KBCB - April, 2016,” Weather History for Blacksburg, VA,
13-Apr-2016. [Online]. Available at:
https://www.wunderground.com/history/airport/kbcb/2016/4/13/dailyhistory.html?req_city=blac
ksburg. [Accessed: 04-May-2016].
X. Appendices
Appendix A
16. Evaluation of Sources:
[1] Strong. This website dedicates its content to describing the product that is it selling, the
Phantom 4 drone, so the information stated contributes to an accurate representation of the
product itself.
[2] Medium to Strong. New Scientist is a magazine dedicated to providing accurate scientific and
technological information. The author of this article, David Hambling, is a credible journalist
who has been writing science articles for different magazines for years.
[3] Strong. This is a credible source as it comes straight from the University of Minnesota.
[4]Strong. This page is dedicated to selling magnesium, so the price must be exact.
[5]Medium to Strong. The author is an aerospace engineer, which gives him credibility over the
subject of aerospace, however the website does not provide any outside information regarding
publication, copyright, etc.
[6] Strong. This page is dedicated to selling its product, the GoPro, so the information it has on
this device must be accurate.
[7] Medium to Strong. Life Science is a reputable source, however not an official educational
science site. The author has a masters degree in journalism and typically covers many science
related articles for Life Science.
[8] Strong. This page does an exceptional job explaining what a horizontal stabilizer is and is
credible because it stems from a .gov site.
[9] Medium to Strong. This page is dedicated to displaying weather and all other aspects related
to weather, however it does not include any important outside information.
Appendix B
Table A. Invoice for Billable Hours
Week
Number
3 4 5 6 7 8 9 10 11 12 13 Total
Hours
per
Person
Task Team
Roles &
Team
Charter
Needs
Assessment
Report,
Project
Schedule
Begin
Research
Contin
ue
Resear
ch
Spring
Break
Trajecto
ry
Module
, Begin
Modeli
ng
Model
Design
Finish
Modeling,
Prepare
Design
Status
Review
DPC Four
Square,
Synthesis
Test Shape
Design
Prototype,
Initial
Concept
Selection
Launch
Prototype,
Final
Presentation
Preeya 0.5 1.5 1 1 0 0.5 0.5 4 2 4 6 21
Justin 0.5 1.5 1 1 0 0.5 0.5 2 2 4 6 19
Christian 0.5 2.5 1 1 0 0.5 0.5 4 3 4 6 23
Ethan 0.5 1.5 1 1 0 0.5 0.5 4 2 4 6 21
Alli 0.5 1.5 1 1 0 0.5 0.5 4 3 4 6 22
17. Saede 0.5 1.5 1 1 0 0.5 0.5 2 1 4 6 18
Grand Total
Hours
124
Total
Amount
($125
person/hour
$15,500
Appendix C
Drawings:
Concept #1
This concept includes square, downward-slanted wings that run through the fuselage. It also
contains a tailfin and a camera, which is positioned on the bottom of the body.
Concept #2
18. This concept has one large wing that is located on top of the body. It not only includes a tailfin
and a camera, but also a horizontal stabilizer.
Appendix D
Synthesis Code Program:
1. %4M Group 1
2. %This code calculates the pressure, velocity, and vertical position
3. %with in the bottle rocket as time moves on
4. clear
5. clc
6.
7. y0 = 0.0; % Initial altitude, ft
8. VT = 0.07063; % Total volume of bottle,2 Liters, expressed in cubic ft
9. VW = 0.01059; % Volume of water, 300 ml, expressed in cubic ft (this is the
recommended maximum volume of water to put in a 2 L bottle)
10. v0 = VT-VW; % Initial volume of air in cubic ft in a 2 liter bottle. A 2 liter
bottle contains 0.07063 cubic feet. The max water volume to put in a 2 L rocket is
0.01059 cubic ft or 300 ml. The air volume for that amount of water is 0.06004
ft^3
11. D = 0.000073; % Rocket drag: 0.5*Cd*x-sectArea *rho. Assume this value of
drag coefficient Cd=.7, rho=.0024sl/ft^3, and a 2 L bottle has 4 in diameter. mr =
.00367; % Empty Mass of the rocket in slugs (53.61 grams)
12. g = 32.2; % Acceleration due to gravity (ft/s^2)
13. P0 = 11520.0;% psf initial bottle air pressure(80 psi)
14. Ae = 0.004;%exit area, sq ft, of a 2 liter bottle
15. Pa = 2116.8;%ambient air pressure psf (14.7 psi)
16. Rho_w = 1.939;%water density in slugs/ft^3
17. mr = input('Enter the empty mass value:');
18. tspan = 5;
19. dt = 0.001; %time intervals
20. npoints = round(tspan/dt);
21.
19. 22. p = zeros(npoints,1);
23. time = zeros(npoints,1);
24. v = zeros(npoints,1);
25. y = zeros(npoints,1);
26.
27. % the initial conditions
28. p(1) = P0;
29. v(1)= v0;
30. y(1)=y0;
31. time(1) = 0.0;
32.
33. for step=1:npoints-1 % loop over the timesteps
34. p(step+1) = p(step) - ((p(step).^2)/(P0*v0))*Ae*(sqrt(2*(p(step)-
Pa)/Rho_w))*dt; %calculates pressure
35.
36. %Prevent rocket pressure from going below atmospheric pressure
37. if p(step+1) < Pa
38. p(step+1) = Pa;
39. end
40.
41. %compute new mass
42. if p(step+1) > Pa
43. Mass = Rho_w*(VT-(P0*v0/p(step))+mr);
44. else
45. Mass = mr;
46. end
47.
48. %Prevent mass from going below the empty rocket mass
49. if Mass < mr
50. Mass = mr;
51. p(step) = Pa;
52. end
53.
54. v(step+1) = v(step) + ((((2*Ae*(p(step)-Pa))-
(D*v(step)*abs(v(step))))/Mass)-g)*dt; %calculates velocity
55.
56. y(step+1) = y(step) + (v(step)*dt); %calculaes vertical position
57.
58. time(step+1) = time(step) + dt;
59.
60. %Prevent altitude from going below 0
61. if y(step+1) < 0
62. v(step+1) = 0;
63. y(step+1) = 0;
64. end
65.
20. 66. end
67.
68. plot(time,p);
69. xlabel('time(sec)')
70. ylabel('pressure (psf)')
71. title('Pressure Variation Over Time')
72. figure
73. plot(time,v);
74. xlabel('time(sec)')
75. ylabel('velocity (ft/sec)')
76. title('Velocity Variation Over Time')
77. figure
78. plot(time,y);
79. xlabel('time(sec)')
80. ylabel('Altitude (ft)')
81. title('Altitude Variation Over Time')
Appendix E
Project Schedule:
22. Figure 4: Side view of prototype concept #2 Figure 5: Top view of prototype concept #2
As seen in Figures 4 & 5, the wings of the model were created using 3 different layers of
styrofoam. They were glued and taped into place to ensure stability and to increase the
aerodynamics of the prototype. As shown at the bottom of Figure 4, a few platforms were placed
on the bottom of the prototype; these represent the camera that will be placed in the relative area
on our actual product. The AA battery shown on the left side of Figure 4 represents the electric
engine that will go inside our drone to power the propeller.