This document provides an overview of the hardware components used in a cosmic ray detector setup, including scintillation counters, a QuarkNet DAQ readout board, a GPS receiver, cables, and a power supply. The QuarkNet DAQ board receives signals from up to four scintillation counters, performs signal processing and logic, and outputs data records with timing information to study cosmic ray interactions. Students can perform calibration studies, flux experiments, muon lifetime experiments, and shower studies using this detector setup.
Elena Guardincerri of Los Alamos National Laboratory is developing a muon detector to image reinforcement structures inside the dome of Florence Cathedral in Italy. Her novel muon imaging technique can penetrate thick structures like the dome's masonry walls and identify dense materials like iron. She is designing lightweight muon trackers made of carbon fiber tubes that will be suspended inside the dome. This will help determine if iron reinforcement exists inside and provide a detailed crack profile to assess the dome's stability. The results could help preserve the architectural treasure by informing preservation efforts. Her work may also help nuclear security by detecting smuggled nuclear materials and mapping underground structures.
CERN is a global scientific research organization located in Geneva, Switzerland that operates the largest particle physics laboratory in the world. It was founded in 1954 and has over 10,000 scientists from over 100 countries working on experiments to study the fundamental constituents of matter and the forces that act between them. CERN generates enormous amounts of data from experiments like the Large Hadron Collider, with over 15 petabytes of new data generated each year that is distributed to computing centers around the world for analysis. Solving the mysteries of the universe through these experiments requires advanced computing technologies and global collaboration to process and make sense of the massive volumes of data being collected.
WE1.L10 - INTERANNUAL VARIABILITY IN CLIMATE PRODUCTS FROM THE ATMOSPHERIC IN...grssieee
The document summarizes the Atmospheric Infrared Sounder (AIRS) instrument on NASA's Aqua satellite. AIRS measures atmospheric temperature and humidity profiles as well as greenhouse gases. It has provided over 8 years of global observations used to improve weather forecasts and validate climate models. AIRS data has also enabled over 350 research publications studying topics like tropical cyclones, the Madden-Julian oscillation, and trends in outgoing longwave radiation.
Final year project: To Design and Test a low cost Gamma Ray detectorChristopher Mitchell
The document describes designing and testing a low-cost gamma radiation detector using a smartphone camera. The author tests various parameters of the smartphone detector such as calibration with radiation sources, thermal noise, distance effects, shielding effects, timing resolution, and efficiency compared to semiconductor detectors. Although not as efficient as professional detectors, the smartphone detector provides a low-cost option for estimating radiation dose that is more accessible than specialized equipment.
The document provides information about Dr. Debjyoti Banerjee and his research related to nano-devices for cooling, sensing, and storage. His lab focuses on multi-phase flows and heat transfer and has received over 20 grants for projects related to nano-sensors, thermal management, and biomedical microfluidics. Some of the key enhancements his research has demonstrated include a 40% improvement in heat exchanger performance using carbon nanotube nanofluids and a 300% improvement in pool boiling using carbon nanotube coatings.
This document summarizes the discovery and analysis of a Type Ia supernova (SN Ia) at a redshift of 1.71, the most distant spectroscopically confirmed SN Ia at the time. The Hubble Space Telescope was used to obtain spectroscopy and photometry of the supernova. Analysis of the spectroscopy confirms it as a SN Ia with 92% confidence. The photometry is used to determine the supernova's distance, which agrees with the predictions of the ΛCDM cosmological model. This distant supernova helps improve constraints on the nature and behavior of dark energy in the early universe.
Medical Imaging - Opportunities for Business Seminar
24/01/12
Session 2 Technology Showcase
Three technologies developed or enhances at the University of Leicester are presented
The document discusses various applications of the electromagnetic spectrum from visible light to radio frequencies. It describes instruments that observe different wavelengths, including the Hubble Space Telescope, weather satellites, infrared and ultraviolet telescopes, x-ray and gamma ray observatories, and radio antennas. Examples of images captured across the spectrum illustrate observations of astronomical phenomena, Earth's atmosphere and surface, and scientific discoveries enabled by each wavelength band.
Elena Guardincerri of Los Alamos National Laboratory is developing a muon detector to image reinforcement structures inside the dome of Florence Cathedral in Italy. Her novel muon imaging technique can penetrate thick structures like the dome's masonry walls and identify dense materials like iron. She is designing lightweight muon trackers made of carbon fiber tubes that will be suspended inside the dome. This will help determine if iron reinforcement exists inside and provide a detailed crack profile to assess the dome's stability. The results could help preserve the architectural treasure by informing preservation efforts. Her work may also help nuclear security by detecting smuggled nuclear materials and mapping underground structures.
CERN is a global scientific research organization located in Geneva, Switzerland that operates the largest particle physics laboratory in the world. It was founded in 1954 and has over 10,000 scientists from over 100 countries working on experiments to study the fundamental constituents of matter and the forces that act between them. CERN generates enormous amounts of data from experiments like the Large Hadron Collider, with over 15 petabytes of new data generated each year that is distributed to computing centers around the world for analysis. Solving the mysteries of the universe through these experiments requires advanced computing technologies and global collaboration to process and make sense of the massive volumes of data being collected.
WE1.L10 - INTERANNUAL VARIABILITY IN CLIMATE PRODUCTS FROM THE ATMOSPHERIC IN...grssieee
The document summarizes the Atmospheric Infrared Sounder (AIRS) instrument on NASA's Aqua satellite. AIRS measures atmospheric temperature and humidity profiles as well as greenhouse gases. It has provided over 8 years of global observations used to improve weather forecasts and validate climate models. AIRS data has also enabled over 350 research publications studying topics like tropical cyclones, the Madden-Julian oscillation, and trends in outgoing longwave radiation.
Final year project: To Design and Test a low cost Gamma Ray detectorChristopher Mitchell
The document describes designing and testing a low-cost gamma radiation detector using a smartphone camera. The author tests various parameters of the smartphone detector such as calibration with radiation sources, thermal noise, distance effects, shielding effects, timing resolution, and efficiency compared to semiconductor detectors. Although not as efficient as professional detectors, the smartphone detector provides a low-cost option for estimating radiation dose that is more accessible than specialized equipment.
The document provides information about Dr. Debjyoti Banerjee and his research related to nano-devices for cooling, sensing, and storage. His lab focuses on multi-phase flows and heat transfer and has received over 20 grants for projects related to nano-sensors, thermal management, and biomedical microfluidics. Some of the key enhancements his research has demonstrated include a 40% improvement in heat exchanger performance using carbon nanotube nanofluids and a 300% improvement in pool boiling using carbon nanotube coatings.
This document summarizes the discovery and analysis of a Type Ia supernova (SN Ia) at a redshift of 1.71, the most distant spectroscopically confirmed SN Ia at the time. The Hubble Space Telescope was used to obtain spectroscopy and photometry of the supernova. Analysis of the spectroscopy confirms it as a SN Ia with 92% confidence. The photometry is used to determine the supernova's distance, which agrees with the predictions of the ΛCDM cosmological model. This distant supernova helps improve constraints on the nature and behavior of dark energy in the early universe.
Medical Imaging - Opportunities for Business Seminar
24/01/12
Session 2 Technology Showcase
Three technologies developed or enhances at the University of Leicester are presented
The document discusses various applications of the electromagnetic spectrum from visible light to radio frequencies. It describes instruments that observe different wavelengths, including the Hubble Space Telescope, weather satellites, infrared and ultraviolet telescopes, x-ray and gamma ray observatories, and radio antennas. Examples of images captured across the spectrum illustrate observations of astronomical phenomena, Earth's atmosphere and surface, and scientific discoveries enabled by each wavelength band.
BOSCO Uganda is a non-profit organization located in Gulu District, Uganda that was established in 2006. Its mission is to provide information and communication technology solutions to foster socio-economic development and peace building in rural communities in Northern Uganda. It has installed rural computer and internet access at 25 sites including schools, communities, and institutions. It also provides training and develops local content. BOSCO Uganda has received recognition for its work, including winning the 2010 Breaking Borders Award for its promotion of online free expression.
This document describes a workshop where participants will build a mathematical model of the relationship between the height of stacked Styrofoam cups and the number of cups stacked. Participants will collect measurement data, analyze it using Excel to determine the linear regression model and assess goodness of fit, and explore how the model responds to changes in cup parameters and measurement errors. The goal is to demonstrate how Excel can be used to visualize data and build mathematical models.
This document provides instruction on basic internet usage, including navigating to websites via URLs, using search engines like Google to find information, and reading online news articles. It explains what the internet is, how to access websites, how to search for information and websites using keywords in Google, and how to find various news sources online to stay informed. The goal is to familiarize users with fundamental "Web 1.0" functions of the internet as a resource.
This lesson teaches users how to use Gmail for email communication and collaboration. It covers signing up for a Gmail account, sending and receiving emails, attaching documents to emails, forwarding emails, using the archive feature, and Gchat for instant messaging within Gmail. The goal is to familiarize users with Gmail's collaboration tools.
Pabo Save The Orphans Assn 2009 Annual ReportTom Loughran
Pabo Save the Orphans Association conducted various activities from July 2007 to December 2008 to support orphans and vulnerable children. Key activities included sensitizing over 1,100 community members on peace programs, generating income through bead making for child mothers, and supporting the education of 46 orphans and vulnerable children. The organization also documented community activities and promoted human rights. However, a lack of funds and equipment posed challenges to operations.
This document lists age-adjusted death rates per 100,000 population for various causes of death in the United States and its territories for 2004. The rates are highest in Mississippi at 300.1, Alabama at 276.3, and Oklahoma at 284.3. They are lowest in Minnesota at 144.3, Utah at 175, and Vermont at 186.6. The data comes from the Centers for Disease Control and Prevention's National Center for Health Statistics and is used to compare death rates between areas while controlling for differences in population composition.
Place-based education uses the local community and environment as a context for learning across subjects and helps increase academic achievement, social relationships, and environmental quality. The Our Place project will have students in Indiana, which ranks poorly for environmental quality, work on an inquiry-based environmental project to clean up their air and water while contributing to their community and learning cooperatively.
Mass, energy and momentum at cms i2 u2Tom Loughran
The document discusses mass, energy, and momentum at the CMS detector at the LHC. It explains that:
1) At high energies, energy and momentum are practically equivalent according to the equation E2 = p2 + m2, where mass terms become negligible. This allows energy to be calculated from momentum measurements.
2) The mass of a parent particle that decays can be determined by subtracting the momentum term p2 from the total energy term E2 of its decay products, giving m2.
3) At the LHC, initial energies and momenta of collisions are not precisely known, so conservation cannot be used directly, but transverse momentum is assumed to be zero initially and its conservation is used.
This document is a PhD thesis submitted by Jamie Fleming to the University of Edinburgh. It contains the following key points:
1. The thesis presents the first measurement of the E double-polarisation observable for the γn → K+Σ- reaction using data from CLAS at JLab.
2. It also provides an overview of Jamie's work developing and constructing the scintillating hodoscope for the CLAS12 Forward Tagger detector upgrade at JLab.
3. The thesis contains acknowledgements, an abstract, introduction to hadron spectroscopy and theoretical models, background on kaon photoproduction reactions, and a review of previous experimental data on the topic.
This two-day professional development course taught by Dr. Alan Tribble focuses on the space environment and its implications for spacecraft design. The course provides an introduction to the space environment, including the vacuum, neutral gases, plasma, radiation, and micrometeoroids. It emphasizes techniques for minimizing environmental effects through proactive design. Participants receive course materials and can apply the concepts to engineering systems with adequate performance margins and spacecraft survivability. The instructor has extensive experience in space environments and effects analysis for NASA and DoD programs.
The document provides an overview of the Science Gateway Group at Indiana University. It introduces the group members and describes their focus areas as developing open source software for cyberinfrastructure like Apache Rave and Apache Airavata. It discusses the group's work on extending collaborations with application scientists in various domains. The document also outlines possibilities for collaboration with the PTI CREST Lab on topics like scientific workflows and generalized execution frameworks.
Computational Training and Data Literacy for Domain ScientistsJoshua Bloom
This document discusses training domain scientists in computational and data skills. It notes the increasing amount of data in fields like astronomy and challenges of traditional approaches. It advocates teaching skills like statistics, machine learning, and programming. Examples are given of bootcamps, seminars and degree programs in these areas at UC Berkeley taught by CS and statistics faculty. Challenges discussed include fitting such training into formal curricula and ensuring participation from underrepresented groups. The creation of collaborative spaces is proposed to better connect domain scientists with methodological experts to help scientists address the growing role of data in their fields.
Research Poster: Radiation testing on electronics Jemaris Martes
This document summarizes a research project that aims to study the effects of radiation on electronics by exposing three modules - ArduLab, Kicksat, and ArduSat - to different space environments. The modules will run programmed algorithms to identify specific radiation effects like total ionizing dose, displacement damage, and single event effects. It is expected that the modules will experience some radiation damage, particularly single event effects, providing valuable data on how electronics are affected by these conditions in space. The results of this experiment could inform further research on developing radiation mitigation techniques.
This document provides an overview of a four-day course on space systems fundamentals taught by Dr. Mike Gruntman. The course covers topics such as space missions and applications, the space environment, orbital mechanics, spacecraft subsystems, and more. It aims to provide engineers and managers with an understanding of spacecraft design concepts and technologies. The document outlines the course schedule, learning objectives, and provides sample material on coordinate systems and time scales used in space exploration.
This document provides an overview of a four-day course on space systems fundamentals taught by Dr. Mike Gruntman. The course covers topics such as space missions and applications, the space environment, orbital mechanics, spacecraft subsystems, and more. It aims to provide engineers and managers with an understanding of spacecraft design concepts and technologies. The document includes the course outline, learning objectives, instructor biography, and information on registering for upcoming courses in New Mexico and Maryland in May and June 2009.
This document discusses the field of astroinformatics, which uses machine learning algorithms and computational tools to analyze large astronomy datasets. It summarizes that quasars are extremely luminous celestial objects located far from Earth that emit unusually large amounts of energy. The document also notes that analyzing detailed spectra of thousands of quasars using machine learning could help identify anomalous emission patterns. Finally, it predicts that astroinformatics will be crucial for making sense of the huge volumes of data that will be produced by next-generation telescopes.
Radiation testing on electronics official posterPROSSATeam
This document discusses an experiment to study the effects of radiation on electronics in space using three modules: ArduLab, KickSat, and ArduSat. ArduLab will be exposed on the International Space Station and run an algorithm to indicate radiation damage using LEDs. KickSat satellites will send a signal code to indicate long term effects. ArduSat will collect radiation exposure data while orbiting and is expected to experience single event effects. The modules will be programmed with algorithms and launched between 2013-2014 to test and compare the radiation effects on each in different orbital environments. The results could help develop techniques to mitigate radiation damage to electronics.
Lattice Energy LLC - Electroweak neutron production explains anomalous CNO el...Lewis Larsen
Many-body collective electroweak neutron production on dust grain surfaces and inside plasma-filled stellar magnetic flux tubes explains anomalous presence of CNO elements detected spectroscopically in atmospheres of some white dwarf stars. Closer to home, LENR CNO analogue could potentially be commercialized for green power generation here on Earth.
This document provides an outline and overview of the topics covered in a course on remote sensing and its applications in soil resource mapping. The outline includes definitions of remote sensing, the history and development of the technology, principles of electromagnetic radiation and its interactions with targets, spectral signatures, resolutions, satellite orbits, and applications of remote sensing. Examples are given of different remote sensing systems like the human eye. A definition of remote sensing is provided. The history section describes early developments dating back to the 1600s and important events in the 1900s. The document gives an overview of active and passive remote sensing as well as elements involved like the energy source, radiation, recording, transmission and more. Remote sensing principles, websites and literature are also listed.
This document discusses using k-means clustering to detect minerals from remote sensing images. It begins with an abstract describing using k-means clustering on hyperspectral images to segment and extract features to detect minerals like giacomo. It then provides background on remote sensing, k-means clustering algorithms, and describes the giacomo mineral deposit in Peru that contains silicon dioxide and titanium dioxide. It concludes with discussing using sobel edge detection as part of the mineral detection process from remote sensing images.
ExoSGAN and ExoACGAN: Exoplanet Detection using Adversarial Training AlgorithmsIRJET Journal
This document discusses using generative adversarial networks (GANs) to detect exoplanets from light curve data. Specifically, it proposes two models: ExoSGAN which uses a semi-supervised GAN (SGAN) and ExoACGAN which uses an auxiliary classifier GAN (ACGAN). SGAN and ACGAN are designed to handle issues with imbalanced and unlabeled data. The models are trained on K2 light curve data and achieve 100% recall and precision on the test set, outperforming previous methods. The document provides background on exoplanet detection techniques and reviews related work applying machine learning, including CNNs, to find planets from Kepler and K2 mission data.
BOSCO Uganda is a non-profit organization located in Gulu District, Uganda that was established in 2006. Its mission is to provide information and communication technology solutions to foster socio-economic development and peace building in rural communities in Northern Uganda. It has installed rural computer and internet access at 25 sites including schools, communities, and institutions. It also provides training and develops local content. BOSCO Uganda has received recognition for its work, including winning the 2010 Breaking Borders Award for its promotion of online free expression.
This document describes a workshop where participants will build a mathematical model of the relationship between the height of stacked Styrofoam cups and the number of cups stacked. Participants will collect measurement data, analyze it using Excel to determine the linear regression model and assess goodness of fit, and explore how the model responds to changes in cup parameters and measurement errors. The goal is to demonstrate how Excel can be used to visualize data and build mathematical models.
This document provides instruction on basic internet usage, including navigating to websites via URLs, using search engines like Google to find information, and reading online news articles. It explains what the internet is, how to access websites, how to search for information and websites using keywords in Google, and how to find various news sources online to stay informed. The goal is to familiarize users with fundamental "Web 1.0" functions of the internet as a resource.
This lesson teaches users how to use Gmail for email communication and collaboration. It covers signing up for a Gmail account, sending and receiving emails, attaching documents to emails, forwarding emails, using the archive feature, and Gchat for instant messaging within Gmail. The goal is to familiarize users with Gmail's collaboration tools.
Pabo Save The Orphans Assn 2009 Annual ReportTom Loughran
Pabo Save the Orphans Association conducted various activities from July 2007 to December 2008 to support orphans and vulnerable children. Key activities included sensitizing over 1,100 community members on peace programs, generating income through bead making for child mothers, and supporting the education of 46 orphans and vulnerable children. The organization also documented community activities and promoted human rights. However, a lack of funds and equipment posed challenges to operations.
This document lists age-adjusted death rates per 100,000 population for various causes of death in the United States and its territories for 2004. The rates are highest in Mississippi at 300.1, Alabama at 276.3, and Oklahoma at 284.3. They are lowest in Minnesota at 144.3, Utah at 175, and Vermont at 186.6. The data comes from the Centers for Disease Control and Prevention's National Center for Health Statistics and is used to compare death rates between areas while controlling for differences in population composition.
Place-based education uses the local community and environment as a context for learning across subjects and helps increase academic achievement, social relationships, and environmental quality. The Our Place project will have students in Indiana, which ranks poorly for environmental quality, work on an inquiry-based environmental project to clean up their air and water while contributing to their community and learning cooperatively.
Mass, energy and momentum at cms i2 u2Tom Loughran
The document discusses mass, energy, and momentum at the CMS detector at the LHC. It explains that:
1) At high energies, energy and momentum are practically equivalent according to the equation E2 = p2 + m2, where mass terms become negligible. This allows energy to be calculated from momentum measurements.
2) The mass of a parent particle that decays can be determined by subtracting the momentum term p2 from the total energy term E2 of its decay products, giving m2.
3) At the LHC, initial energies and momenta of collisions are not precisely known, so conservation cannot be used directly, but transverse momentum is assumed to be zero initially and its conservation is used.
This document is a PhD thesis submitted by Jamie Fleming to the University of Edinburgh. It contains the following key points:
1. The thesis presents the first measurement of the E double-polarisation observable for the γn → K+Σ- reaction using data from CLAS at JLab.
2. It also provides an overview of Jamie's work developing and constructing the scintillating hodoscope for the CLAS12 Forward Tagger detector upgrade at JLab.
3. The thesis contains acknowledgements, an abstract, introduction to hadron spectroscopy and theoretical models, background on kaon photoproduction reactions, and a review of previous experimental data on the topic.
This two-day professional development course taught by Dr. Alan Tribble focuses on the space environment and its implications for spacecraft design. The course provides an introduction to the space environment, including the vacuum, neutral gases, plasma, radiation, and micrometeoroids. It emphasizes techniques for minimizing environmental effects through proactive design. Participants receive course materials and can apply the concepts to engineering systems with adequate performance margins and spacecraft survivability. The instructor has extensive experience in space environments and effects analysis for NASA and DoD programs.
The document provides an overview of the Science Gateway Group at Indiana University. It introduces the group members and describes their focus areas as developing open source software for cyberinfrastructure like Apache Rave and Apache Airavata. It discusses the group's work on extending collaborations with application scientists in various domains. The document also outlines possibilities for collaboration with the PTI CREST Lab on topics like scientific workflows and generalized execution frameworks.
Computational Training and Data Literacy for Domain ScientistsJoshua Bloom
This document discusses training domain scientists in computational and data skills. It notes the increasing amount of data in fields like astronomy and challenges of traditional approaches. It advocates teaching skills like statistics, machine learning, and programming. Examples are given of bootcamps, seminars and degree programs in these areas at UC Berkeley taught by CS and statistics faculty. Challenges discussed include fitting such training into formal curricula and ensuring participation from underrepresented groups. The creation of collaborative spaces is proposed to better connect domain scientists with methodological experts to help scientists address the growing role of data in their fields.
Research Poster: Radiation testing on electronics Jemaris Martes
This document summarizes a research project that aims to study the effects of radiation on electronics by exposing three modules - ArduLab, Kicksat, and ArduSat - to different space environments. The modules will run programmed algorithms to identify specific radiation effects like total ionizing dose, displacement damage, and single event effects. It is expected that the modules will experience some radiation damage, particularly single event effects, providing valuable data on how electronics are affected by these conditions in space. The results of this experiment could inform further research on developing radiation mitigation techniques.
This document provides an overview of a four-day course on space systems fundamentals taught by Dr. Mike Gruntman. The course covers topics such as space missions and applications, the space environment, orbital mechanics, spacecraft subsystems, and more. It aims to provide engineers and managers with an understanding of spacecraft design concepts and technologies. The document outlines the course schedule, learning objectives, and provides sample material on coordinate systems and time scales used in space exploration.
This document provides an overview of a four-day course on space systems fundamentals taught by Dr. Mike Gruntman. The course covers topics such as space missions and applications, the space environment, orbital mechanics, spacecraft subsystems, and more. It aims to provide engineers and managers with an understanding of spacecraft design concepts and technologies. The document includes the course outline, learning objectives, instructor biography, and information on registering for upcoming courses in New Mexico and Maryland in May and June 2009.
This document discusses the field of astroinformatics, which uses machine learning algorithms and computational tools to analyze large astronomy datasets. It summarizes that quasars are extremely luminous celestial objects located far from Earth that emit unusually large amounts of energy. The document also notes that analyzing detailed spectra of thousands of quasars using machine learning could help identify anomalous emission patterns. Finally, it predicts that astroinformatics will be crucial for making sense of the huge volumes of data that will be produced by next-generation telescopes.
Radiation testing on electronics official posterPROSSATeam
This document discusses an experiment to study the effects of radiation on electronics in space using three modules: ArduLab, KickSat, and ArduSat. ArduLab will be exposed on the International Space Station and run an algorithm to indicate radiation damage using LEDs. KickSat satellites will send a signal code to indicate long term effects. ArduSat will collect radiation exposure data while orbiting and is expected to experience single event effects. The modules will be programmed with algorithms and launched between 2013-2014 to test and compare the radiation effects on each in different orbital environments. The results could help develop techniques to mitigate radiation damage to electronics.
Lattice Energy LLC - Electroweak neutron production explains anomalous CNO el...Lewis Larsen
Many-body collective electroweak neutron production on dust grain surfaces and inside plasma-filled stellar magnetic flux tubes explains anomalous presence of CNO elements detected spectroscopically in atmospheres of some white dwarf stars. Closer to home, LENR CNO analogue could potentially be commercialized for green power generation here on Earth.
This document provides an outline and overview of the topics covered in a course on remote sensing and its applications in soil resource mapping. The outline includes definitions of remote sensing, the history and development of the technology, principles of electromagnetic radiation and its interactions with targets, spectral signatures, resolutions, satellite orbits, and applications of remote sensing. Examples are given of different remote sensing systems like the human eye. A definition of remote sensing is provided. The history section describes early developments dating back to the 1600s and important events in the 1900s. The document gives an overview of active and passive remote sensing as well as elements involved like the energy source, radiation, recording, transmission and more. Remote sensing principles, websites and literature are also listed.
This document discusses using k-means clustering to detect minerals from remote sensing images. It begins with an abstract describing using k-means clustering on hyperspectral images to segment and extract features to detect minerals like giacomo. It then provides background on remote sensing, k-means clustering algorithms, and describes the giacomo mineral deposit in Peru that contains silicon dioxide and titanium dioxide. It concludes with discussing using sobel edge detection as part of the mineral detection process from remote sensing images.
ExoSGAN and ExoACGAN: Exoplanet Detection using Adversarial Training AlgorithmsIRJET Journal
This document discusses using generative adversarial networks (GANs) to detect exoplanets from light curve data. Specifically, it proposes two models: ExoSGAN which uses a semi-supervised GAN (SGAN) and ExoACGAN which uses an auxiliary classifier GAN (ACGAN). SGAN and ACGAN are designed to handle issues with imbalanced and unlabeled data. The models are trained on K2 light curve data and achieve 100% recall and precision on the test set, outperforming previous methods. The document provides background on exoplanet detection techniques and reviews related work applying machine learning, including CNNs, to find planets from Kepler and K2 mission data.
This proposal seeks funding to develop laser-based optical trapping, or "tractor beams", for remote sampling of particles in space. Tractor beams could non-invasively collect samples from comets, asteroids, planetary atmospheres and surfaces. This would enable new types of sampling missions without landers or sample return. The proposal outlines developing tractor beam technology through lab experiments and scaling it for potential applications on spacecraft. Developing tractor beams could significantly expand NASA's capability to remotely collect and analyze samples throughout the solar system.
Felipe A. Colazo Petit's curriculum vitae summarizes his education and professional experience in physics. He holds a Master's degree in Physics from Fisk University and has worked as an associate test engineer at NASA Goddard Space Flight Center. His experience includes designing, building, and testing detectors for studies of the cosmic microwave background and adaptive optics systems.
Introduction to the problem of spatial indexing for spherical coordinate systems, as those used in astronomy. Part of the virtual observatory course by Juan de Dios Santander Vela, as imparted for the MTAF (Métodos y Técnicas Avanzadas en Física, Advanced Methods and Techniques in Physics) Master at the University of Granada (UGR).
Strong field science core proposal for uph ill siteahsanrabbani
This document provides a 3-year project summary for an international collaboration on strong field science:
1. The project aims to strengthen India's participation in experiments studying matter under extreme light intensities through international collaboration.
2. Indian researchers will perform experiments at international facilities and host foreign researchers, while also building expertise for potential future domestic facilities.
3. The project aims to consolidate Indian efforts in this area and increase international exposure, with a goal of developing robust Indian competence in studying matter with petawatt laser pulses.
The presentation discusses the evolution of space-based magnetometers from early fluxgate designs to more advanced solid-state technologies. It provides context on magnetometry and its importance for scientific discovery in fields like heliophysics, planetary science, and earth science. Examples are given of magnetometers used on past and current NASA missions. The presentation then shifts to discussing the speaker's current research developing a new silicon carbide magnetometer for space applications.
Virtual Observatories as the Drivers of Space Science - Robert Rankin, Univer...Cybera Inc.
Robert Rankin, Professor of Physics and Astronomy at the University of Alberta, presented these slides as part of the Cybera Summit 2010 session "The Evolution of Collaborative Science." For more information please visit http://www.cybera.ca/evolution-collaborative-science
The document provides a vision for the future of ubiquitous sensor networks and introduces Quantum-Pi, a company developing quantum tunneling sensor technologies. Quantum-Pi was founded in 1999 and has developed nano-electro-mechanical sensors for applications such as oil/gas, security, medicine, aviation and more. The document discusses Quantum-Pi's devices, collaborations, facilities, and the market potential for its quantum tunneling linear encoder and dynamic sensor products. It presents the technological principles behind quantum tunneling sensors and examples of prototypes fabricated at research institutions.
These slides were presented at the 5th annual Collaboration for STEM Education, Research and Commercialization Forum, Winter 2012, at the University of Notre Dame
Collaborating for STEM Education, Research and Commercialization Forum VII ma...Tom Loughran
These slides were presented at the 8th annual Collaboration for STEM Education, Research and Commercialization Forum at the University of Notre Dame, March 1 2014.
This is the full set of slides from the 11th annual Collaboration for STEM Education, Research and Commercialization Forum held on Feb 24, 2018 at the University of Notre Dame's Jordan Hall of Science.
This study analyzed data from a detector that measured cosmic ray muons to determine their lifetime. The researcher used Matlab to draw a histogram of the data and fit an exponential decay curve to calculate the lifetime. The curve had a slope that corresponded to a lifetime of 2.63 microseconds, consistent with known literature values for the muon lifetime.
CE3-Uganda Fostering Entrepreneurship in an Electrified, Connected EcoysystemTom Loughran
This document outlines a plan to foster entrepreneurship in Northern Uganda through connectivity, electrification, and entrepreneurship (CE3). The region still has high rates of people living off-grid, but there are nascent livelihood ecosystems emerging around increased connectivity and electrification. The plan involves piloting small solar microgrids and providing training to 1,000 entrepreneurs, with a goal of contributing to 400 new jobs. Looking forward, the plan aims to create productive use CE3 ecosystems at a larger kW scale by having electrified businesses also reach households. The goal is a sustainable model of local off-grid utilities providing 30 kW of solar power with storage and entrepreneurial support programs.
Human week 2015 Pabo, Amuru District, UgandaTom Loughran
This document discusses the annual 16 Days of Activism Against Gender-Based Violence campaign which takes place from November 25th to December 10th each year. The campaign aims to raise awareness about violence against women and children and encourage society to acknowledge this as a societal problem. It also provides objectives of the campaign, which include attracting communities to fight violence against women and children and emphasizing that the solution lies with collective action from all members of society. The document encourages various actions people can take to support the campaign, such as wearing a white ribbon, volunteering with organizations, speaking out against abuse, and spreading awareness on social media.
The document announces a Science Forum & Tour being held on October 22nd as part of the 2nd Annual Notre Dame Soft Polymer Materials Symposium. The forum, targeted at local high school and college students and teachers, will include a faculty presentation on nanotechnology applications followed by discussion and a tour of campus facilities. The goal is to stimulate student interest in STEM fields by providing hands-on polymer materials experience, introducing characterization techniques, and helping connect students with university mentors for science fair projects.
Collaborating for Education and Research Forums I-VII SummaryTom Loughran
The Collaborating for Education and Research Forum has brought together K-12 teachers and university outreach professionals in Michiana for seven years, drawing an average of 150 participants annually. The Forum promotes integrated STEM education and provides opportunities for collaboration across educational institutions. Over 450 unique participants have attended, including more than 200 K-12 teachers who have also participated in other outreach events. The Forum highlights STEM programs and issues of importance to regional educators.
No place like home sept_18_2014_Ward_lectureTom Loughran
Over the past 20 years, techniques have discovered over 3000 exoplanets. While the search for an "Earth Twin" has so far been unsuccessful, it is increasingly recognized that habitable zones for life could be broader than initially thought, beyond conditions similar to Earth. The talk will explain exoplanet discovery techniques and explore new ideas about possible habitats for life in space, most of which would be very different than conditions on Earth.
Carl Wieman, a Nobel Laureate in Physics and professor at Stanford University, will give a talk titled "Taking a Scientific Approach to Science Education" on Monday, September 15 at 7 PM in the Leighton Concert Hall at the DeBartolo Performing Arts Center. He will discuss narrowing the gap between scientific advancements and science education by explaining the relationship between research and effective teaching and learning. The event is free and open to the public, with ticket distribution beginning one hour before.
The College of Science at the University of Notre Dame and the South Bend Alumni Association are hosting a mixed doubles tennis tournament called "ACE for Science" to raise money for K-12 science programs in South Bend schools. Players will be paired based on skill level and can include members of the Notre Dame community, local community members, and celebrities. The tournament will take place on April 26th at 10am at the Eck Tennis Pavilion on Notre Dame's campus.
Collaborating for Education and Research Forum IIITom Loughran
The document discusses plans to build an integrated STEM community in Michiana by creating engagement opportunities between university faculty, K-12 educators, and students. It aims to develop this into a set of regional professional development pathways defined and pursued collaboratively. Opportunities mentioned include building on the successful BioEYES model in other disciplines like nanotechnology and astronomy. Sessions at an upcoming forum will focus on sharing models like BioEYES, addressing new state science standards, exploring university involvement in K-12, and using online tools to collaborate more efficiently. The goal is to establish a research-centric, computationally literate, collaborative community that invites broad participation in advancing STEM.
Collaborating for Education and Research Forum IVTom Loughran
This document summarizes the keynote presentation "Collaborating for Education and Research: Why Forum IV" given by Thomas Loughran at Forum IV on January 22, 2011 at the University of Notre Dame. It outlines the challenges facing education, highlights opportunities through increased collaboration and advancing research, and proposes NDeRC's strategy of developing an integrated STEM community through craft, community, and culture to help revitalize the Michiana region. Specific initiatives and upcoming sessions at the forum are also listed.
Tourism Investment Opportunities in Northern UgandaTom Loughran
From the forward:
The departure of the Lord’s Resistance Army has breathed new life into northern Uganda. The region is enjoying more visitors and its reputation as a “no go” area is being gradually reversed. Improved security is allowing the rapid development of the region and generating increasing interest from businesses and tourists alike.
With this in mind, the Wildlife Conservation Society and the Uganda Tourism Association have undertaken a study, with support from USAID through the WILD programme, to gauge the potential of tourism in northern Uganda and to promote its development and expansion. The study focused on untapped or underutilized attractions in Nebbi, Arua, Moyo and Adjumani Districts in the West Nile sub-region; Amuru, Gulu, Lamwo, Kitgum and Pader Districts in the central part of the Northern Region and Kaabong District in Karamoja. Murchison Falls National Park was not included in this study in light of its already well-developed tourism infrastructure.
This publication is the result of that study and its purpose is to introduce prospective investors to the variety of natural, cultural and historical attractions in the region that can be drawn on for tourism. It also is intended to support the Ugandan government’s plans to diversify tourism products within the country – particularly along the Nile. It is our hope that it will inspire responsible private and government investment that will bring economic benefits to the local communities as well as protect and preserve the area’s varied and unique resources.
The Wildlife Conservation Society is thankful to Charles Abola and Jim Ayorekire of Image Consult for carrying out this study. We also acknowledge the valuable contributions of the Uganda Wildlife Authority, the National Forestry Authority, Uganda Museums, the Ministry of Trade, Tourism and Industry, the Ugandan Tourist Board and relevant district officials to this study, in addition to the development of Uganda’s tourism industry as a whole. We also appreciate the valuable input from private sector companies, who have shown genuine interest in the opportunities provided by northern Uganda.
A final word of thanks goes to USAID for its generous support to conservation and tourism in Uganda in general and the WILD programme in particular. It is USAID’s assistance that supported the study and allowed this brochure to be developed and printed.
Northern Uganda is open for business and tourists!
Jan F Broekhuis, Director, WCS
Amos Wekesa , Chairperson, UTA
Collaborating for Education and Research Forum VII ProgramTom Loughran
This is the program for our Collaborating for Education and Research Forum, our 7th annual, held in the Jordan Hall of Science on the campus of the University of Notre Dame on March 1, 2014 from 8:30 AM until 2:00 PM.
Dr. Klaus Mainzer public presentation at Notre Dame: "CNN Philosophy: From C...Tom Loughran
Cellular Nonlinear/Neural Network (CNN) technology is both a revolutionary concept and an experimentally proven new computing paradigm. It lays the groundwork for a new approach to information processing that is based on brain-inspired spatial-temporal behavior in large-scale, cellular arrays of nanoeletronic processing elements. Prof. and Dr. Klaus Mainzer will explore CNN philosophy’s links with deep problems of epistemology and broach the ways that bio-inspired computing leads to questions of societal acceptance and ethical benchmarks.
Prof. Dr. Klaus Mainzer is a philosopher of science and director of the Center for Technology and Society at the University of Technology, Munich. He studies the foundations and future perspectives of science and technology focusing on mathematical treatment and computer modeling as well as complex systems in the natural world, science, business, and society. His research areas include self-organization, chaos theory, artificial intelligence, and artificial life.
Mainzer is a participant in NDnano’s NSF-EAGER grant, “Computer Architectures for 2020 and Beyond.”
Spotlighting South Bend - December 20, 2013Tom Loughran
From the event organizer:
Dear Friend,
You are invited on Friday, December 20, 2013 to spend a day honoring the innovation that has built and is still growing South Bend.
As a community, we honor our past that relentlessly pursued the innovative spirit that built our community and embodied the name Studebaker. Fifty years ago on December 20th the lights turned off on the last Studebaker facility. However, the hard work and craftsmanship that thrived in those plants live on.
From 10:00 am to 4:30 pm, Union Station Technology Center is opening Ivy Tower (Building 84) for guided tours. The Studebaker Driver’s Club will offer special tours, with Studebaker retiree guides starting at 2:30 pm. The Studebaker Administration Building will also be available for tours from 12:00 pm to 4:30 pm. All tours will start from 635 S. Lafayette Street in South Bend. With the existing development plans, this could be one of the last times that the facility will be open for tours in its original state.
At 5:00 pm in Union Station’s grand hall, we will host an event to spotlight South Bend’s innovation. Specifically, the program will honor former Studebaker retirees, highlight current innovation in our community and point to innovation of the future.
Shortly after 6:00 pm, please join us outside Union Station, near Coveleski Stadium and throughout downtown to see our City spotlighted, demonstrating that the light of innovation that sparked our community remains on and bright today.
You are also encouraged to visit the Studebaker National Museum (free admission that day), the South Bend Museum of Art, and other downtown South Bend activities. All of the events are showcased in the attached flyer.
Please join us in spotlighting South Bend on this important day in our City’s history.
Sincerely,
Kevin M. Smith
President & CEO
Union Station Technology Center
Your One-Stop Shop for Python Success: Top 10 US Python Development Providersakankshawande
Simplify your search for a reliable Python development partner! This list presents the top 10 trusted US providers offering comprehensive Python development services, ensuring your project's success from conception to completion.
Driving Business Innovation: Latest Generative AI Advancements & Success StorySafe Software
Are you ready to revolutionize how you handle data? Join us for a webinar where we’ll bring you up to speed with the latest advancements in Generative AI technology and discover how leveraging FME with tools from giants like Google Gemini, Amazon, and Microsoft OpenAI can supercharge your workflow efficiency.
During the hour, we’ll take you through:
Guest Speaker Segment with Hannah Barrington: Dive into the world of dynamic real estate marketing with Hannah, the Marketing Manager at Workspace Group. Hear firsthand how their team generates engaging descriptions for thousands of office units by integrating diverse data sources—from PDF floorplans to web pages—using FME transformers, like OpenAIVisionConnector and AnthropicVisionConnector. This use case will show you how GenAI can streamline content creation for marketing across the board.
Ollama Use Case: Learn how Scenario Specialist Dmitri Bagh has utilized Ollama within FME to input data, create custom models, and enhance security protocols. This segment will include demos to illustrate the full capabilities of FME in AI-driven processes.
Custom AI Models: Discover how to leverage FME to build personalized AI models using your data. Whether it’s populating a model with local data for added security or integrating public AI tools, find out how FME facilitates a versatile and secure approach to AI.
We’ll wrap up with a live Q&A session where you can engage with our experts on your specific use cases, and learn more about optimizing your data workflows with AI.
This webinar is ideal for professionals seeking to harness the power of AI within their data management systems while ensuring high levels of customization and security. Whether you're a novice or an expert, gain actionable insights and strategies to elevate your data processes. Join us to see how FME and AI can revolutionize how you work with data!
Ivanti’s Patch Tuesday breakdown goes beyond patching your applications and brings you the intelligence and guidance needed to prioritize where to focus your attention first. Catch early analysis on our Ivanti blog, then join industry expert Chris Goettl for the Patch Tuesday Webinar Event. There we’ll do a deep dive into each of the bulletins and give guidance on the risks associated with the newly-identified vulnerabilities.
Main news related to the CCS TSI 2023 (2023/1695)Jakub Marek
An English 🇬🇧 translation of a presentation to the speech I gave about the main changes brought by CCS TSI 2023 at the biggest Czech conference on Communications and signalling systems on Railways, which was held in Clarion Hotel Olomouc from 7th to 9th November 2023 (konferenceszt.cz). Attended by around 500 participants and 200 on-line followers.
The original Czech 🇨🇿 version of the presentation can be found here: https://www.slideshare.net/slideshow/hlavni-novinky-souvisejici-s-ccs-tsi-2023-2023-1695/269688092 .
The videorecording (in Czech) from the presentation is available here: https://youtu.be/WzjJWm4IyPk?si=SImb06tuXGb30BEH .
Letter and Document Automation for Bonterra Impact Management (fka Social Sol...Jeffrey Haguewood
Sidekick Solutions uses Bonterra Impact Management (fka Social Solutions Apricot) and automation solutions to integrate data for business workflows.
We believe integration and automation are essential to user experience and the promise of efficient work through technology. Automation is the critical ingredient to realizing that full vision. We develop integration products and services for Bonterra Case Management software to support the deployment of automations for a variety of use cases.
This video focuses on automated letter generation for Bonterra Impact Management using Google Workspace or Microsoft 365.
Interested in deploying letter generation automations for Bonterra Impact Management? Contact us at sales@sidekicksolutionsllc.com to discuss next steps.
HCL Notes and Domino License Cost Reduction in the World of DLAUpanagenda
Webinar Recording: https://www.panagenda.com/webinars/hcl-notes-and-domino-license-cost-reduction-in-the-world-of-dlau/
The introduction of DLAU and the CCB & CCX licensing model caused quite a stir in the HCL community. As a Notes and Domino customer, you may have faced challenges with unexpected user counts and license costs. You probably have questions on how this new licensing approach works and how to benefit from it. Most importantly, you likely have budget constraints and want to save money where possible. Don’t worry, we can help with all of this!
We’ll show you how to fix common misconfigurations that cause higher-than-expected user counts, and how to identify accounts which you can deactivate to save money. There are also frequent patterns that can cause unnecessary cost, like using a person document instead of a mail-in for shared mailboxes. We’ll provide examples and solutions for those as well. And naturally we’ll explain the new licensing model.
Join HCL Ambassador Marc Thomas in this webinar with a special guest appearance from Franz Walder. It will give you the tools and know-how to stay on top of what is going on with Domino licensing. You will be able lower your cost through an optimized configuration and keep it low going forward.
These topics will be covered
- Reducing license cost by finding and fixing misconfigurations and superfluous accounts
- How do CCB and CCX licenses really work?
- Understanding the DLAU tool and how to best utilize it
- Tips for common problem areas, like team mailboxes, functional/test users, etc
- Practical examples and best practices to implement right away
Nunit vs XUnit vs MSTest Differences Between These Unit Testing Frameworks.pdfflufftailshop
When it comes to unit testing in the .NET ecosystem, developers have a wide range of options available. Among the most popular choices are NUnit, XUnit, and MSTest. These unit testing frameworks provide essential tools and features to help ensure the quality and reliability of code. However, understanding the differences between these frameworks is crucial for selecting the most suitable one for your projects.
Digital Marketing Trends in 2024 | Guide for Staying AheadWask
https://www.wask.co/ebooks/digital-marketing-trends-in-2024
Feeling lost in the digital marketing whirlwind of 2024? Technology is changing, consumer habits are evolving, and staying ahead of the curve feels like a never-ending pursuit. This e-book is your compass. Dive into actionable insights to handle the complexities of modern marketing. From hyper-personalization to the power of user-generated content, learn how to build long-term relationships with your audience and unlock the secrets to success in the ever-shifting digital landscape.
Programming Foundation Models with DSPy - Meetup SlidesZilliz
Prompting language models is hard, while programming language models is easy. In this talk, I will discuss the state-of-the-art framework DSPy for programming foundation models with its powerful optimizers and runtime constraint system.
TrustArc Webinar - 2024 Global Privacy SurveyTrustArc
How does your privacy program stack up against your peers? What challenges are privacy teams tackling and prioritizing in 2024?
In the fifth annual Global Privacy Benchmarks Survey, we asked over 1,800 global privacy professionals and business executives to share their perspectives on the current state of privacy inside and outside of their organizations. This year’s report focused on emerging areas of importance for privacy and compliance professionals, including considerations and implications of Artificial Intelligence (AI) technologies, building brand trust, and different approaches for achieving higher privacy competence scores.
See how organizational priorities and strategic approaches to data security and privacy are evolving around the globe.
This webinar will review:
- The top 10 privacy insights from the fifth annual Global Privacy Benchmarks Survey
- The top challenges for privacy leaders, practitioners, and organizations in 2024
- Key themes to consider in developing and maintaining your privacy program
In the rapidly evolving landscape of technologies, XML continues to play a vital role in structuring, storing, and transporting data across diverse systems. The recent advancements in artificial intelligence (AI) present new methodologies for enhancing XML development workflows, introducing efficiency, automation, and intelligent capabilities. This presentation will outline the scope and perspective of utilizing AI in XML development. The potential benefits and the possible pitfalls will be highlighted, providing a balanced view of the subject.
We will explore the capabilities of AI in understanding XML markup languages and autonomously creating structured XML content. Additionally, we will examine the capacity of AI to enrich plain text with appropriate XML markup. Practical examples and methodological guidelines will be provided to elucidate how AI can be effectively prompted to interpret and generate accurate XML markup.
Further emphasis will be placed on the role of AI in developing XSLT, or schemas such as XSD and Schematron. We will address the techniques and strategies adopted to create prompts for generating code, explaining code, or refactoring the code, and the results achieved.
The discussion will extend to how AI can be used to transform XML content. In particular, the focus will be on the use of AI XPath extension functions in XSLT, Schematron, Schematron Quick Fixes, or for XML content refactoring.
The presentation aims to deliver a comprehensive overview of AI usage in XML development, providing attendees with the necessary knowledge to make informed decisions. Whether you’re at the early stages of adopting AI or considering integrating it in advanced XML development, this presentation will cover all levels of expertise.
By highlighting the potential advantages and challenges of integrating AI with XML development tools and languages, the presentation seeks to inspire thoughtful conversation around the future of XML development. We’ll not only delve into the technical aspects of AI-powered XML development but also discuss practical implications and possible future directions.
Skybuffer AI: Advanced Conversational and Generative AI Solution on SAP Busin...Tatiana Kojar
Skybuffer AI, built on the robust SAP Business Technology Platform (SAP BTP), is the latest and most advanced version of our AI development, reaffirming our commitment to delivering top-tier AI solutions. Skybuffer AI harnesses all the innovative capabilities of the SAP BTP in the AI domain, from Conversational AI to cutting-edge Generative AI and Retrieval-Augmented Generation (RAG). It also helps SAP customers safeguard their investments into SAP Conversational AI and ensure a seamless, one-click transition to SAP Business AI.
With Skybuffer AI, various AI models can be integrated into a single communication channel such as Microsoft Teams. This integration empowers business users with insights drawn from SAP backend systems, enterprise documents, and the expansive knowledge of Generative AI. And the best part of it is that it is all managed through our intuitive no-code Action Server interface, requiring no extensive coding knowledge and making the advanced AI accessible to more users.
Generating privacy-protected synthetic data using Secludy and MilvusZilliz
During this demo, the founders of Secludy will demonstrate how their system utilizes Milvus to store and manipulate embeddings for generating privacy-protected synthetic data. Their approach not only maintains the confidentiality of the original data but also enhances the utility and scalability of LLMs under privacy constraints. Attendees, including machine learning engineers, data scientists, and data managers, will witness first-hand how Secludy's integration with Milvus empowers organizations to harness the power of LLMs securely and efficiently.
Dive into the realm of operating systems (OS) with Pravash Chandra Das, a seasoned Digital Forensic Analyst, as your guide. 🚀 This comprehensive presentation illuminates the core concepts, types, and evolution of OS, essential for understanding modern computing landscapes.
Beginning with the foundational definition, Das clarifies the pivotal role of OS as system software orchestrating hardware resources, software applications, and user interactions. Through succinct descriptions, he delineates the diverse types of OS, from single-user, single-task environments like early MS-DOS iterations, to multi-user, multi-tasking systems exemplified by modern Linux distributions.
Crucial components like the kernel and shell are dissected, highlighting their indispensable functions in resource management and user interface interaction. Das elucidates how the kernel acts as the central nervous system, orchestrating process scheduling, memory allocation, and device management. Meanwhile, the shell serves as the gateway for user commands, bridging the gap between human input and machine execution. 💻
The narrative then shifts to a captivating exploration of prominent desktop OSs, Windows, macOS, and Linux. Windows, with its globally ubiquitous presence and user-friendly interface, emerges as a cornerstone in personal computing history. macOS, lauded for its sleek design and seamless integration with Apple's ecosystem, stands as a beacon of stability and creativity. Linux, an open-source marvel, offers unparalleled flexibility and security, revolutionizing the computing landscape. 🖥️
Moving to the realm of mobile devices, Das unravels the dominance of Android and iOS. Android's open-source ethos fosters a vibrant ecosystem of customization and innovation, while iOS boasts a seamless user experience and robust security infrastructure. Meanwhile, discontinued platforms like Symbian and Palm OS evoke nostalgia for their pioneering roles in the smartphone revolution.
The journey concludes with a reflection on the ever-evolving landscape of OS, underscored by the emergence of real-time operating systems (RTOS) and the persistent quest for innovation and efficiency. As technology continues to shape our world, understanding the foundations and evolution of operating systems remains paramount. Join Pravash Chandra Das on this illuminating journey through the heart of computing. 🌟
Have you ever been confused by the myriad of choices offered by AWS for hosting a website or an API?
Lambda, Elastic Beanstalk, Lightsail, Amplify, S3 (and more!) can each host websites + APIs. But which one should we choose?
Which one is cheapest? Which one is fastest? Which one will scale to meet our needs?
Join me in this session as we dive into each AWS hosting service to determine which one is best for your scenario and explain why!
Taking AI to the Next Level in Manufacturing.pdfssuserfac0301
Read Taking AI to the Next Level in Manufacturing to gain insights on AI adoption in the manufacturing industry, such as:
1. How quickly AI is being implemented in manufacturing.
2. Which barriers stand in the way of AI adoption.
3. How data quality and governance form the backbone of AI.
4. Organizational processes and structures that may inhibit effective AI adoption.
6. Ideas and approaches to help build your organization's AI strategy.
1. QuarkNet/Walta/CROP
Cosmic Ray Detectors
User’s Manual
Jeff Rylander and Tom Jordan, Fermilab
R. J. Wilkes, Hans-Gerd Berns and Richard Gran, U. Washington
August 2004
3. Classroom Cosmic Ray Detector User’s Manual
QuarkNet/Walta/CROP
Cosmic Ray Detectors
User’s Manual
This manual provides information for setting up and using a cosmic ray detector with the
QuarkNet Version 2 Data Acquisition (DAQ) board and ancillary hardware. It serves both
beginning and advanced users.
Much of the technical information was originally compiled in a user’s manual written by R.
J. Wilkes. Hans Berns, Rik Gran, Sten Hansen, and Terry Kiper contributed some of the
technical documentation with input from the practical experience of many beta testers.1
Although some of the components of your cosmic ray detector may have come from various
sources, the heart of the detector is the QuarkNet DAQ board. The development of this board
is a collaborative effort involving Fermilab, the University of Nebraska and the University of
Washington. Appendix A has a description of the history of this project.
Project Development Team
Fermilab: Sten Hansen, Tom Jordan, Terry Kiper
Univeristy of Nebraska: Dan Claes, Jared Kite, Victoria Mariupolskaya,
Greg Snow
University of Washington: Hans Berns, Toby Burnett, Paul Edmon,
Rik Gran, Ben Laughlin, Jeremy Sandler, Graham Wheel, Jeffrey Wilkes
1
For more technical documentation on the DAQ board, see http://www.phys.washington.edu/~walta/qnet_daq/
i
4. Classroom Cosmic Ray Detector User’s Manual
Table of Contents
Chapter 1 In the Classroom
Cosmic Ray Experiments within the Classroom
How Can I Use Cosmic Ray Detectors in My Classroom?
What Experiments Can My Students Perform?
Chapter 2 Hardware Introduction
Hardware Overview
The DAQ Readout Board
Power Supply
GPS Receiver
Scintillation Counters
Cables for Connecting to PC
Chapter 3 Data Display
Data Display on a PC
Keyboard Commands
Chapter 4 The DAQ Card
GPS Observation
Singles and Coincidence Rate Measurement
Data Collection
Chapter 5 Data Upload and Analysis
QuarkNet Website Overview
Data Upload to the Server
Analysis Tools
Chapter 6 Advanced Topics
Counter Plateauing
Data Words
Coincidence Counting Variations
On-board Barometer Calibration
Appendices
Appendix A: History of Card Development
Appendix B: Schematic Diagrams
Appendix C: Terminal Emulator Setup
Appendix D: Precise Event Time Calculation Algorithm
Appendix E: Details of Time Coincidence and Data Handling
Appendix F: Acronym and Jargon Dictionary
ii
6. Classroom Cosmic Ray Detector User’s Manual
Chapter 1: In the Classroom
Cosmic Ray Experiments very short -ived and generally decay into
For most of today’s particle physics experi- daughter particles before reaching the
ments, large accelerators accelerate particles earth’s surface. The charged pions, for in-
to very high energies. However, it is possi- stance, will decay into a muon and a neu-
ble to do high-energy physics in your school trino:
without a particle accelerator! Nature serves
as an accelerator for cosmic rays—particles π- µ- + ν µ
that are of astrophysical origin (It is not
completely understood!) and seem to be eve- or
rywhere throughout the universe. These
“primary” cosmic rays, which are mainly π+ µ+ + ν µ.
protons (and a few heavier nuclei), interact
with nucleons in the earth’s upper atmos- Although these reactions are not the only
phere in much the same way that fixed target possibilities—they are examples of common
collisions occur at particle physics laborato- reactions that produce secondary particles
ries. When these primary particles interact and their daughters. Counting all secondary
with nucleons in the atmosphere, they pro- particles detected at sea level, 70% are
duce mainly pions and kaons. In the colli- muons, 29% are electrons and positrons, and
sions, if most of the incoming momentum is 1% are heavier particles.
transferred to an atmospheric proton, the
following reactions are common: If these secondary particles have sufficient
energy, they may in turn interact with other
p + p p + p + π+ + π° + π- particles in the atmosphere producing a
“shower” of secondary particles. The parti-
and cles in this shower will strike a wide area on
the earth’s surface (perhaps several m2 or
p + p p + n + π+ + π+ + π-. even km2) nearly simultaneously. Figure 1
illustrates one of these showers.
If most of the momentum is transferred to a
neutron, then these reactions are common: Although your students can do several cos-
mic ray experiments with a single classroom
p + n p + p + π+ + π- + π- setup, the QuarkNet website
<http://quarknet.fnal.gov/grid/> provides
and student access to data from multiple cosmic
ray detectors to detect and study larger
p + n p + n + π+ + π° + π-. showers. Several professional versions of
this same experiment are taking data that
may help determine the origin of some of
The products of such interactions are called
these highly energetic primary cosmic rays.
“secondary” particles or “secondary” cosmic
rays. Some of these products, however, are
7. Classroom Cosmic Ray Detector User’s Manual
experiments in parallel with your “standard”
curriculum with days set aside periodically
for cosmic ray detector work.
After an introduction to cosmic rays, the
equipment, and the research questions that
physicists ask in this field, have student
groups write up a proposal for the experi-
ment that they want to perform. These ex-
periments might include calibration and per-
formance studies, muon lifetime experi-
ments, shower studies, or flux studies as a
function of one of many variables, e.g., time
of day, solar activity, east/west asymmetry,
angle from vertical, barometric pressure, etc.
Your students can also look for particles that
are strongly correlated in time and may be
part of a wide-area shower.
Figure 1. A cosmic ray shower produced by Once proposals are accepted, give each stu-
a primary cosmic ray entering the earth’s dent “collaboration” a few days to a week to
atmosphere.
run their experiment. In some cases, two
groups might pool their time and share the
How Can I Use a Cosmic Ray same data but for different physics goals.
This is not unlike how real high-energy
Detector In My Classroom? physics experiments are done! If time per-
The very nature of cosmic ray experiments mits, students can do a second run with the
is quite different from traditional labs that student-suggested modifications.
can be completed in a lab period or a couple
of lab periods. Cosmic ray experiments typi- While one group is using the hardware,
cally require a great deal of run time to col- other groups can design their setup, analyze
lect data. Extra class time, however, is not their data (or other data), visit the “Poster”
something most teachers have in an already section of the QuarkNet cosmic ray website
full course. You may also wonder how to to research the results of other student
provide each student time to do an experi- groups, etc. Having your students post their
ment when you have only one setup. work here and/or having them give oral
These are realistic questions. As a possible presentations (sometimes with guest physi-
solution, the following approach allows you cists!) may make for a great summary to the
not only to incorporate these experiments project.
into your course but also to help your stu-
dents discover how high-energy physics ex-
periments are really done. What Experiments Can My
Organize the cosmic ray experiments as a Student Perform?
long-term project that spans a quarter or There are four categories of experiments that
even more. If students work on this project students can do with the comic ray detec-
intermittently, you can run these cosmic ray tors:
8. Classroom Cosmic Ray Detector User’s Manual
1. Calibrations and performance studies these muons as they travel to earth should be
2. Flux experiments at least 100 µs:
3. Muon lifetime experiments
4. Shower studies v muon 3x10 8 m / s
t flight = = = 100 µs .
d 30 x10 3 m
Calibrations and Performance This calculation assumes that muons are
Studies traveling at the speed of light—anything
Before students can “trust” the cosmic ray slower would require even more time. If a
equipment, they can and should do some student can determine the muon lifetime (as
calibrations to study the response of the described in Chapter 5) and show that it is
counters and the board. Calibration studies significantly less than this time, they are
include plateauing the counters, threshold presented with the wonderful dilemma that
selection and barometer calibration. These the muon’s time of flight is longer than its
are discussed in Chapter 5. In addition, the lifetime!
QuarkNet online analysis tools include a
“system performance” study for uploaded This time dilation “proof” assumes that all
data. The details of this study are outlined in muons are created in the upper atmosphere.
Chapter 5 and on the website. Although this is actually a good approxima-
tion, your students cannot test it. However,
by using the mean lifetime value and by
Flux Experiments measuring flux rates at two significantly dif-
Your students can do a variety of flux ex- ferent elevations, you can develop experi-
periments investigating such things as cos- mental proof for time dilation. This experi-
mic ray flux as a function of time of day, ment requires you to have access to a
solar activity, east/west asymmetry (show- mountain, an airplane, or collaboration with
ing the µ+/µ- ratio by assuming these a team from another school that is at a sig-
charged particles will bend in the earth’s nificantly different altitude! Here is a won-
magnetic field), angle from vertical, baro- derful opportunity for schools to work to-
metric pressure, altitude. The list goes on. gether proving time dilation. A very thor-
This can be an exciting set of experiments as ough explanation of this experiment is out-
students study the factors that they want to lined in the 1962 classroom movie titled,
test. Chapter 5 discusses flux studies in more “Time Dilation: An Experiment with Mu
detail. Mesons.” 2 This movie helps you (and your
students) understand how the muon lifetime
measurement (along with flux measurements
Muon Lifetime Experiment to Ver- at two different altitudes) can be used to
verify time dilation.
ify Time Dilation
A classic modern physics experiment to
verify time dilation is the measurement of
the muon mean lifetime. Since nearly all of
Shower Studies
With the GPS device connected to your
the cosmic ray muons are created in the up-
DAQ board, the absolute time stamp allows
per part of the atmosphere (≈30 km above
the earth’s surface), the time of flight for
2
This 30 minute movie can be ordered on CD for
$10 from http://www.physics2000.com/.
9. Classroom Cosmic Ray Detector User’s Manual
a network of detectors (at the same site or at
different schools) to study cosmic ray show-
ers. Your students can look for small show-
ers or collaborate with other schools in your
area to look for larger showers.
The QuarkNet online analysis tools allow
students to not only look for showers but to
make predictions about the direction from
which the shower (and thus the primary
cosmic ray) originated. Details for doing
shower studies can be found in Chapter 5
and on the QuarkNet website.
10. Classroom Cosmic Ray Detector User’s Manual
Chapter 2: Hardware Introduction
Hardware Overview For this setup, the DAQ board takes the sig-
Figure 2 shows a typical cosmic ray detector nals from the counters and provides signal
setup composed of: processing and logic basic to most nuclear
1. Counters—scintillators, light guides, and particle physics experiments. The DAQ
photomultiplier tubes and bases (two board can anlyze signals from up to four
shown). PMTs. (We show two in the figure.) The
2. QuarkNet DAQ board. board produces a record of output data
3. 5 VDC adapter. whenever the PMT signal meets a pre-
4. GPS receiver. defined trigger criterion (for example, when
5. GPS extension cable. two or more PMTs have signals above some
6. RS-232 cable (to link to computer serial predetermined threshold voltage, within a
port). certain time window). The output data re-
7. Optional RS-232 to USB adapter (to link cord, which can be sent via a standard RS-
to computer USB port instead of serial 232 serial interface to any PC, contains tem-
port). poral information about the PMT signals.
8. Lemo signal cables. This information includes: how many chan-
9. Daisy-chained power cables. nels had above-threshold signals, their
relative arrival times (precise to 0.75 ns),
1
9
4
3
9
8
2
5
7 6
Figure 2. A typical cosmic ray detector setup.
11. Classroom Cosmic Ray Detector User’s Manual
and the starting and stopping times for each such as counting rates, auxiliary GPS data,
detected pulse. In addition, an external GPS and environmental sensor data (temperature
receiver module provides the absolute UTC and pressure).
time of each trigger, accurate to about 50 ns.
This allows counter arrays using separate This chapter includes an overview of each
DAQ boards—such as different schools in a major component shown in Figure 2. Addi-
wide-area array or two sets of counters at the tional details regarding some components
same site—to correlate their timing data. are in the appendices.
Keyboard commands allow you to define
trigger criteria and retrieve additional data,
Figure 3. The QuarkNet DAQ v2 board with major components labeled.
DAQ Readout Board text lines readable by any terminal-emulator
Figure 3 is a picture of the DAQ board with program. In addition, a GPS clock provides
several major components labeled. This accurate event time data synchronized to
board is the logic link between the scintilla- Universal Time (UTC), so widely separated
tion counters and the PC. The board pro- sites can compare data. In datastream mode,
vides discriminators and trigger logic for the DAQ board outputs a series of text lines
four channels of PMTs. The board includes reporting event data: trigger time in UTC
five built-in scalers, allowing simultaneous (with 24 ns resolution and absolute accuracy
counts of singles on each channel, plus trig- about 100 ns), leading and trailing edge
gers at whatever logic level you specify (2- times for each pulse recorded within the
to 4-fold majority logic). coincidence time window (with 0.75 ns pre-
cision), and data from the GPS and internal
A standard RS-232 interface can be con- clocks. Additional keyboard commands al-
nected to any PC (Windows, Linux or Mac). low reading of temperature, barometric pres-
The datastream consists of simple ASCII sure and other sensors.
12. Classroom Cosmic Ray Detector User’s Manual
Figure 4. Block diagram of the QuarkNet DAQ v2 board.
Board Components mV threshold with NIM discriminators and
Figure 4 is a block diagram of the QuarkNet have x10 amplification, your threshold level
DAQ v2 board. (See Appendix B for a on the QuarkNet DAQ board should be set
schematic diagram.) to -300 mV.
Discriminators Complex Programmable Logic Device
PMT signals are first pre-amplified by a (CPLD)
factor determined from a set of changeable Trigger logic is implemented using a CPLD
resistors (Amplification factor x10 is used chip. Software revisions for this chip must
for QuarkNet, x2 by CROP, x1 by be prepared using special software but can
WALTA.) Discriminators are implemented be downloaded via the serial port. This
using voltage comparator chips with the ref- flexibility allows the engineers to distribute
erence threshold voltage varied via screw- updates that alter the fast logic, if necessary.
driver adjustable potentiometers (trimpots). Any trigger logic level from singles to 4-
Threshold levels can be set from 0 to -750 fold can be set by keyboard commands to
mV by adjusting each potentiometer while the board. Majority logic is used: any com-
monitoring voltage at a nearby test point. bination of three active channels causes a
It is important to remember that the voltage trigger at the 3-fold level, for example.
comparators look at the amplifier output, so
raw PMT signal levels are multiplied by any
amplification factor present before being
compared. For example, if you used a -30
13. Classroom Cosmic Ray Detector User’s Manual
Time-to-Digital Converters (TDCs) reported whenever the board is started up.
Discriminator output pulses are fed into While the board components are rated for
TDCs3 which measure the arrival time of temperatures between –20°C and +80°C, the
leading and trailing pulse edges. TDCs keep board temperature should not normally go
track of their state (high or low) at 0.75 ns above +50°C.
time intervals. If the trigger criterion is satis-
fied, the TDC data are latched and read out, A second temperature sensor is located on
giving leading and trailing edge times for the booster board built into the GPS cable’s
each channel relative to the trigger time in “far end” DB9 connector. This sensor can be
units of 0.75 ns. This allows you to calculate used to log outdoor temperature at the
PMT pulse widths (time over threshold, or counter locations, and is read out with a
TOT, see Figure 5) as a crude estimate of keyboard command. The GPS module may
pulse area and thus energy. be damaged if its temperature goes below
–40º C or above +85º C.4
A barometric pressure sensor is built into the
board as well. It can also be calibrated and
read out (in units of kPa) with a keyboard
command.
Board Functionality
Figure 5. Typical PMT pulse from which
the Time Over Threshold (TOT) can be
Threshold Detection and Setting
determined. After amplification, the PMT signals are fed
to voltage comparators. The comparators set
a HIGH logic level whenever the amplified
Microcontroller (MCU) PMT signal exceeds their negative threshold
The MCU is really just a special-purpose voltage setting as shown in Figure 6. This
CPU that provides the onboard ‘slow’ logic logic level has 0.75 ns resolution. This
(with a time scale of microseconds, not means that we can measure the time differ-
nanoseconds) to interface the board to you ence between pulses on different channels at
via a terminal window or equivalent on your the same site down to less than a nanosec-
PC. At present, the MCU can be repro- ond! We depend on the GPS clocks, with 24
grammed to redefine functionality only by ns resolution, for timing between school
using special software and burn-in hardware. sites.
Auxiliary Sensors
There is a temperature sensor built into the
microcontroller chip. This sensor is present
so that CPU temperature can be measured.
This temperature and the supply voltage are 4
At DAQ card power-up or reset, the temperature on the DAQ
card (actually, inside the MCU chip) is reported. Note that this is
3 not a good indicator of air temperature at the card site, even if the
“TDC” is a generic term in particle physics technology. The card is located outdoors, since the chip generates considerable heat
specific chips used on the board are TMCs (“Time Measurement while operating. It is a useful way to make sure the card is healthy,
Chips”). You may see this designation in some documentation. however! Temperatures over +40º C may be dangerous to the
card’s chips.
14. Classroom Cosmic Ray Detector User’s Manual
Reference
ground
Signal after User determined
amplification threshold
Figure 6. A typical negative PMT pulse
showing the user-defined threshold value
compared to reference ground.
To measure the current threshold voltage
value, compare the test points, to ground.
The test points for each threshold are labeled
“TPVTH” and the ground labeled “TPGND” TPVTH
in Figure 7. TPGND
Figure 7. Close-up picture of the DAQ board
Setting the threshold level too high will miss showing threshold test points used to measure
all but those events that correspond to a threshold voltage for each channel.
large amount of energy deposited in the de-
tector; setting the threshold too low will re-
sult in background noise within the elec- The plot shows the singles rate in that chan-
tronics being mistaken as event counts. nel as a function of threshold value. You can
see that the counting rate decreases as the
So how do you determine the appropriate threshold setting increases. Once the thresh-
threshold setting? Consider the graph Figure old value became as high as 0.5 V, the
8 on the next page as a ‘ballpark’ determi- counting rate decreased more linearly. The
nation of the optimum threshold value to use “kink” in the graph may be used to suggest
for a channel. For the data shown in this that noise contaminated the counting rate
graph, the PMT voltage was set to that de- much more significantly when the threshold
termined by plateauing the counter (see sec- was set below 0.5 V. Operating slightly
tion 6.1 for help on how this is done) and above this value is probably the optimum
kept constant throughout the experiment. threshold value to choose.
15. Classroom Cosmic Ray Detector User’s Manual
Threshold Determination
900
800
700
(counts/minute)
Frequency
600
500
400
300
200
100
0
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Threshold (V)
Figure 80. A graph of frequency vs. threshold for a counter used to de-
termine threshold setting.
Coincidence Logic Rate Counters
The DAQ board can also determine whether The card has five built-in counters, num-
signals in separate channels are coincident in bered 0 through 4: counters 0 through 3 re-
time. For example, if the trigger criterion is cord the singles count for each channel, and
set to 2-fold, then as soon as any channel counter 4 records the trigger count for what-
goes above threshold, a time window is ever coincidence level you have set. By ze-
opened. (Window time-width is adjustable.) roing these counters with a software com-
If any other channel goes above threshold mand, then running the board for a fixed
during this time window, all event data are length of time and reading out the counters
latched and outputted for the overlap time at the end, you can obtain singles rates for
interval when both are active. Notice that each channel as well as the coincidence
pulse data are reported for a time interval rates.
that is not of fixed length but just covers the
overlap period when two or more channels
are active. Leading and trailing edge times Power Supply
are reported for any active channels (not just The board requires a stable +5 VDC power
for the two channels that launched the trig- supply, with 800 mA or greater output cur-
ger), with empty data entries for channels rent. A 110VAC to 5VDC/2.4A modular
that remained inactive during the trigger switching power supply, of the type used for
window. For a single event trigger, the DAQ many small electronic devices, is supplied
board may need to output several lines of with the board. Replacements are readily
data. The first line has an “event flag” for available at Radio Shack or a similar elec-
identification. Any following lines without tronics store.
this flag are simply additional data for the
same event. PMT bases provided by QuarkNet can be
powered by the same +5 VDC power supply
16. Classroom Cosmic Ray Detector User’s Manual
that is plugged into the DAQ board. These if necessary. Although the GPS module’s
bases are daisy-chained from the board us- RS-232 D plug appears conventional, it has
ing a common male-male phono jack cable been modified with a special connector,
which is also readily available at Radio which contains the circuitry required to de-
Shack or similar store. liver DC power to the module and interface
the 1PPS (1 Pulse Per Second) signal to the
Note: It is important to distinguish these board. This connector should not be inserted
DAQ power supply modules from other directly into your PC’s serial port.
units used for computers or other electronic
devices requiring DV voltage. Connection of You may wish to use the GPS module alone
the wrong power supply to your DAQ board to observe satellite data without operating
will probably fry it. the DAQ card. For stand-alone operation of
the GPS module, you need to construct a
special adapter to allow connection of a
GPS Receiver +5VDC power supply directly to the mod-
The external LeadTek GPS module shown ule—you can use the same power supply
in Figure 9 is connected through a special used for the DAQ card. The wiring
cable which has a seemingly-standard D diagram for the adapter is shown in Figure
connector (serial port connector) on the far 10 on the next page. Parts shown in the
end. This connector mates with the commer- wiring diagram can be obtained at most
cial GPS module’s serial connector. How- electronics supply stores. The LED is op-
ever, the special cable’s D connector actu- tional and just blinks to display the 1PPS
ally contains a tiny circuit board with com- signal, indicating valid data.
ponents needed to ensure good performance
over 100’ or longer cables. The GPS clock The GPS module itself is weatherproof, but
will not work if the special cable is not used. the connectors should be protected. Also, the
screws on the cover of the GPS module tend
to rust, so they should be covered with plas-
tic paint or nail polish before deployment
Interfacing the GPS with the DAQ outdoors.
Board
The external GPS module is interfaced to
the Quarknet DAQ board with a special ex- GPS Startup
tension cable, which can be over 100’ long Once powered-up, the GPS module should
quickly “find itself” if it is in a location with
a clear view of at least half the sky. Usually
it does not work well through windows and
should be physically outdoors. The receiver
will lock onto four or more satellites,
download the data needed to operate accu-
rately and start averaging its position and
clock settings at one-second intervals.
Within a few minutes after startup, you
Figure 9. The LeadTek GPS receiver and should obtain accurate GPS data. The unit’s
cable. The cable shown here can be con- LED display blinks red when first powered-
nected to a GPS extension cable. up and searching, and changes to steady-
17. Classroom Cosmic Ray Detector User’s Manual
green when it has acquired enough satellite commercial GPS module transmits the 1PPS
data to locate itself accurately. Time data are signal about 100’ or more without excessive
not accurate until then. timing degradation.
The GPS module provides several kinds of
data. The commercial GPS module directly How to Calculate Event Times
supplies the date and “coarse” time (in UTC, The DAQ board has onboard a 41.667 MHz
not local time) down to milliseconds, or oscillator, which “ticks” every 24 nanosec-
three decimal places after seconds, and re- onds (1/41.667x106 sec). Such a device does
ports its geographic location in latitude and not maintain its frequency very accurately,
longitude down to the equivalent of a few and our oscillator’s frequency may drift by
10s of meters. 10-100 Hz from its nominal value (perhaps
even more under extreme temperature
changes). A counter (scaler) keeps counting
The “1PPS” Signal the clock ticks. Whenever this 32-bit counter
The stock LeadTek GPS module was modi- reaches its maximum capacity of 4.3 billion,
fied slightly for our application to allow the approximately every 100 seconds, it just
more precise timing we need down to 10s of “rolls over” back to zero, like an old car’s
nanoseconds (eight decimal places following odometer, and continues counting. Clock
integer seconds). The GPS receiver outputs calibration occurs the internal clock counter
a logic pulse at the beginning of each UTC every time a 1PPS signal arrives.
second, called the 1PPS (1 Pulse Per Sec-
ond) signal. Find the precise event time by getting the
date and time down to the nearest second
The GPS receiver sends two types of from the GPS module’s coarse time (with
datastreams to the board. The first is RS-232 one correction described below), finding the
ASCII data telling what time it is, at what number of clock ticks between the last 1PPS
latitude, longitude and altitude the receiver and the event trigger, and dividing by the
is, and information about the satellites the number of clock ticks between the last two
receiver is using. The other data is a 5V 1PPS pulses to get the fraction of a second
100ms pulse telling exactly when the data is down to 24 ns precision. Of course, you
true. Each stream of 5V 100ms pulses ar- have to know whether the counter rolled
rives every second, thus the 5V pulse is over during the last second when doing the
named 1 pulse per second (1PPS). The mi- arithmetic.
crocontroller on the board records the
counter value during which the pulse is re- There is a caveat to the previous paragraph:
ceived. The time is according to a counter If the data rate is very slow—less than about
running at ~41.67 MHz. one event per 100 sec—the internal counter
may roll over more than once between
In principle, the leading edges of 1PPS sig- readings. In this case, all bets are off, and
nals from GPS receivers anywhere in the the seconds cannot be reliably calculated.
world are all in synch, to within the accu- The next firmware update will include
racy of the non-military GPS system (about commands to produce an output line at each
100 ns.) This feature allows accurate time 1PPS, and/or automatic DG commands at
synchronization between school sites. The regular intervals, ensuring that the necessary
special connector and cable attached to the
18. Classroom Cosmic Ray Detector User’s Manual
information is logged between counter Using the GPS without the DAQ
rollovers. Board
To use the GPS module via the serial port of
One minor correction is also needed: the a PC (without the DAQ board) requires the
GPS module reports the time down to the construction of a simple adapter circuit
millisecond, but there is a delay of a fraction shown in Figure 10. The LED is optional
of a second relative to the 1PPS edge. For and simply blinks to display the 1PPS signal
example, when the 1PPS signal says it is and indicates when the GPS module has
exactly 12:01:25.000000000, the GPS time locked onto a position and time fix. 5VDC
field in the data record may say it is power can come from a 110VAC adapter or
12:01:24.850. This delay (reported as a PC’s PS/2 mouse jack. Power drawn is
+0.150 sec in this example) will cause you equivalent to what a mouse would consume,
to associate the wrong integer second with and will not affect your computer. You can
the event time if you are not careful. (The substitute a connector to mate with a stan-
GPS time delay may be negative, i.e., a for- dard 5VDC power adapter, available from
ward shift, with the ASCII time data ahead any electronics store.
of the 1PPS signal.) The DAQ board is pro-
grammed to list the delay in milliseconds for
each data record so the reported time in sec-
onds can be corrected to match the 1PPS
data. The algorithm described in Appendix
D implements these calculations.
For people who like really deep-down de-
tails, the delay mentioned above, which you
can determine and correct, is not the whole
story. There is an additional delay of 150-
250 ms, which is unresolvable, since it is
buried in the manufacturer’s firmware.
Luckily, it is too small to cause the rounding
procedure described above to go wrong. Figure 10. The adapter circuit wiring dia-
Remember, all this is just about determining gram required when the GPS is connected
the integer seconds part of the time. Nano- directly to the computer (without connection
second-level timing is not affected. Also, we to the DAQ board).
have not discussed corrections for the an-
tenna cable delay—the event time calculated
is when coincidence occurs at the DAQ Scintillation Counters
board, not at the counters. This is of no con- A typical counter used in this experiment is
sequence as long as all school sites in an ar- shown in Figure 11. A counter is comprised
ray use approximately the same cable of a plastic scintillator, a light guide, a PMT,
lengths, within a few 10s of meters. The al- and a PMT base which provides the neces-
gorithm showing how to get the precise sary operating voltage for the PMT and
event time is shown in Appendix D. sends an electrical signal to the DAQ board
when a light pulse is “seen” by the PMT.
For the counter shown in Figure 11, only the
square portion of the paddle actively scin-
tillates. The trapezoidal shape is merely a
19. Classroom Cosmic Ray Detector User’s Manual
light guide which directs the light toward the nomena, however, is an important one in
PMT using total internal reflection. When helping your students understand the opera-
calculating the surface area of the active tion of the detectors.
portion of your detector, use only the square
portion.
PMT/Base
Along with the production of the DAQ
board, QuarkNet and Fermilab have pro-
duced a Cockcroft-Walton base that can be
used with an RCA 6342 PMT or similar 2”
10-stage tube. This base does not require the
Figure11. A typical cosmic ray counter con- use of a high voltage power supply but is
sisting of scintillator and light guide (the flat powered by the same +5VDC supply that is
paddle region to the right), the PMT (black
cylinder), and the PMT base (light-colored used for the DAQ board. The base is housed
cylinder on the left end.) in an aluminum can (see Figure 12). Appen-
dix B includes a schematic for this PMT
base. If a separate tube and base are used in
It will be necessary to “plateau” your your experiment, you may need to make
counter before the counting rate can be slight resistor modifications to the board in
trusted. Small fluctuations in the high volt- order to achieve the proper signal size after
age can offer significant variations in amplification.
counter response if the operating voltage is
not near the voltage plateau. Details for how The PMT voltage across the first and last
to plateau a counter are in Chapter 6. dynode—the operating tube voltage—ranges
from 0–1600 VDC for the RCA 6342 PMT
and the corresponding base provided by
Scintillators QuarkNet. A potentiometer at the end of the
Since muon flux at sea level is ~1 x 10-2 base can be used for adjusting this voltage.
muons/cm2/sec, and since these comprise The “pot” is marked off from 0 to 10 which
about 70% of the cosmic rays at sea level, a correspond linearly to the voltages from 0 –
detector of significant surface area will help 1600 V. This means that increasing the pot
to increase the counting rate to 10s or even by “1 unit” corresponds to an increase in
100s of events each minute. If shower ex- 160 V across the first and last dynode.
periments or flux studies are of interest, then
increasing surface area is the primary way to If you want to check the value of the tube
increase the counting rate. If muon lifetime voltage, two test points on the end of the
experiments are of interest, however, then base are provided to probe with a standard
increasing the thickness of the scintillator DC low voltage voltmeter (see Figure 12).
will also increase the counting rate since This probe voltage measurement must be
only the muons that have stopped and decay multiplied by 385 to obtain the actual tube
within the detector can be used for lifetime voltage.
studies.
An important question to ask is, “What
The process by which a scintillator scintil- should be the voltage setting for my
lates light when a changed particle traverses counter?” Because the response of each
is not discussed in this manual. This phe- counter is unique, the answer to this ques-
20. Classroom Cosmic Ray Detector User’s Manual
tion is different for each counter. To deter- Lemo cables, which are thin coaxial cables
mine the operating voltage for a particular with “lemo” connectors on the ends, carry
counter, you must “plateau the counter.” the PMT signal to the DAQ board. A toggle
Details can be found in Chapter 6. switch on the end of the base allows you to
turn on/off the tube without disconnecting
the power cable. An amber LED near the
test points tells when the base is “on.”
Cables for Connecting to PC
The DAQ board connects to your PC’s serial
port with a standard serial cable. If your PC
does not have a standard RS-232 serial port,
you can use a USB-to-serial converter,
available commercially.
Test Points
Figure12. The end of a PMT base showing
test points that may be probed with a low
voltage DC voltmeter to measure PMT oper-
ating voltage. A multiplication factor of 385
is used to determine actual tube voltage.
21. Classroom Cosmic Ray Detector User’s Manual
Chapter 3: Data Display
Data Display on a PC a single event may result in more than one
View the data with a terminal emulation line of data! In this section, we discuss the
program such as Zterm (Mac or Windows), meaning of some of the keyboard commands
Hyperterminal (Windows) or a “homemade” that you can type in order to modify/read
Unix-based program you can download various values to/from the board that are not
from the QuarkNet website. See Appendix C displayed on the screen until requested.
for details on setting up these terminal
emulation programs. Your PC is capable of sending commands to
the DAQ board in addition to receiving the
datastream from the board. Figure 14 shows
an example of three keyboard commands
Keyboard Commands that you type in order to measure the tem-
Once the terminal emulator is initialized and perature at the GPS sensor, the value of the
the scintillation counters and board are pow- scalers, and to display GPS data.
ered, you should begin to see data on the
screen that looks something like that shown The “HE” (help) command sends a summary
in Figure 13. of all keyboard commands. Figure 15 shows
this command summary.
The meaning of these “words” will be dis-
cussed in great detail in Chapter 6. Note that
Figure 130. Sample screen of datastream from DAQ board when viewed with a terminal
emulation program.
22. Classroom Cosmic Ray Detector User’s Manual
Figure14. Example of keyboard commands that may be sent to the DAQ board with
the appropriate board responses.
Figure15. A list of all keyboard commands viewable by typing “HE.”
23. Classroom Cosmic Ray Detector User’s Manual
Some of the most commonly used com- Chapters 4 and 6 for more detailed descrip-
mands are discussed in Table 1. See tions of how and when to use these com-
mands.
Keyboard
Description
Command
CD Counters Disabled. Does not write event lines on the PC monitor
even though the scalers will still increment. This is useful when you do
not want to “see” all the data coming in.
CE Counters Enabled. Writes event lines on the PC monitor. This com-
mand has the opposite effect of the CD command.
DS Display Scalers. Displays values of the scalers in hexadecimal. Scal-
ers 0-3 store the singles rates for channels 0-3, and counter 4 records
the number of n-fold coincidences, where “n” is whatever level you
set. These counts are running totals since the last time the counters
were zeroed.
RB Reset Board. Resets scalers and TMC only.
RE Reset Everything. Resets everything (including card setup parameters
that you may have modified); will zero all scalers.
TH Thermometer. Reports reading of temperature sensor on the GPS
module connector, about 3 feet from the GPS module itself.
GP GPS Data. Displays current date, time, GPS position, and number of
satellites visible.
Table 1. Some of the most common keyboard commands with descriptions.
24. Classroom Cosmic Ray Detector User’s Manual
Chapter 4: The DAQ Card
GPS Observation
To read out the current GPS time, latitude, If you connect the GPS module directly to
longitude, altitude and number of satellites your PC’s serial port, as discussed before,
in view, type “GP” as shown in the previous you can also use a software package pro-
section. You can, however, directly monitor vided by LeadTek to display sky maps of
the GPS module’s serial datastream by satellites and other interesting data. This can
sending the command “NM 1.” This com- be found online.
mand will pass all data from the GPS mod- <http://www.phys.washington.edu/~berns/ar
ule directly to your PC. Normally, the chive/Leadtek/GMonitor.exe>
board’s MCU reads, interprets and distills
the raw GPS information to produce the DG
command output. Although this will con- Singles and Coincidence Rate
tinue to be true even after you send the “NM
1” command, you will get many more lines Measurement
of detailed data (in the GPS industry’s stan- Important measurements you want to make
dard NMEA format). Refer to the link to are the rate at which an individual counter is
understand this data format. hit (“singles rate”) as well as the rate at
<http://www.phys.washington.edu/~berns/ar which a 2- to 4-fold coincidence occurs
chive/Leadtek/GPS_Protocol_ReferenceMa (“coincidence rate”). To determine these,
nual.pdf> type the following commands shown in Ta-
ble 2:
To disable NMEA data-forwarding and re-
turn to normal operation, send the command
NM (i.e., no “1”).
CD Counter Disabled. Prevents the datastream from off your screen.
RB Reset Scalers. But immediately after type . . .
DG Display GPS Data. Gives the initial time—when you began counting. (You
could use a stopwatch to measure the elapsed time instead.)
DS Display Scaler. After an adequate amount of time has passed (say 5 min-
utes or so) take the final reading of the scalers and then immediate type . . .
DG Display GPS Data. Give the final time.
Table 2. The keyboard command sequence performed for determining
counting rate.
The counting rates for any particular scaler elapsed time is recorded in scaler 4. Divid-
(0-3) can be determined by dividing the hex ing the number of coincidences by the
valued scaler by the difference of the begin- elapsed time will yield the coincidence rate.
ning and ending times. The number of n-fold Figure 16 illustrates this command sequence
coincidences that occurred within the and the corresponding board outputs.
25. Classroom Cosmic Ray Detector User’s Manual
As an example of the singles rate, consider 3023counts counts
Rsin gles = = 607
the data in which the counting rate for chan- 4.98 min min
nel 0 was BCF = 3023 . The elapsed run
H 10
time was 21:35:45 – 21:30:46 = 4:59 or 4.98
minutes. Thus, the singles rate is
Initial GPS time
Scaler values after elapsed time
Ending GPS time
Figure16. An example of keyboard commands and board responses used to de-
termine the singles counting rate in a particular channel.
Data Collection the datastream appears on your monitor, se-
Once you have setup and tested your equip- lect the command that will allow you to be-
ment and have plateaued the counters, you gin capturing text. You will be prompted to
are ready to collect and save data for a run. type a name and a folder into which these
Although the commands for starting and data will be saved. Your emulator will save
stopping a run vary slightly with each termi- these data as a text file that can be analyzed
nal emulation program (see Appendix C for later. The data will be written to this file
these commands), the idea is the same: Once continuously. For example, opening this text
26. Classroom Cosmic Ray Detector User’s Manual
file while data is being saved will display all the stop command for your particular emu-
the data collected up to that moment. lator. (See Appendix C for this command.)
When you want to stop a run (which could This file can be uploaded to the server and
be minutes, hours or even weeks later!), use the data analyzed.
27. Classroom Cosmic Ray Detector User’s Manual
Chapter 5: Data Upload and Analysis
Figure 17. The QuarkNet Cosmic Ray Collaboration webpage serves as the studenthomepage for the cosmic
ray project.
QuarkNet Website Overview from their detector. A link to the student
homepage is also located here.
Teacher Pages
The QuarkNet teacher activities database is Student Pages
found at The student homepage for this project is
<http://eddata.fnal.gov/lasso/quarknet_g_act <http://quarknet.fnal.gov/grid> (Figure 17).
ivities/view.lasso>.
Among many resources, students will find:
By selecting the “Grid Cosmic Ray Collabo Studies – Interesting questions along
ration” link, you can find out more about with ideas to answer these questions
this project and use online tools for imple- through experiment.
menting this project in your classroom. You Resources – Links to related projects,
will find a page to register their school as physicists and other student group con-
part of the cosmic ray investigations net- tacts.
work so that your students may upload data Upload Data – Links to upload data and
geometry files.
28. Classroom Cosmic Ray Detector User’s Manual
Data Analysis – Powerful analysis tools data run spans more than one day, the data
to analyze data for a variety of experi- will be broken into separate files labeled
ments. Even students without a detector with the appropriate date.
can analyze data.
Poster Session – A method for students
to share their results, search the work of Analysis Tools
other students and collaborate with stu- Once your students have collected and up-
dents at other schools. loaded the data, there are four studies they
can do. Analyze data from your detector as
well any other detector that has uploaded
Data Upload to the Server data. You can even look for coincidences
While many of the cosmic ray detector experi- between your school and other schools if run
ments that your students can do require only the times overlap! This section will explain the
equipment at your local site, analyzing the data is nature of each study/analysis and provide a
cumbersome with software such as Excel. framework from which you can get started.
Working locally discourages student collaboration
like that found in real high-energy experiments.
Accordingly, QuarkNet is developing a website System Performance
that allows data uploads and analysis. This The main objective of the “system performance”
simplifies the analysis of these complex data and study is to understand the quality of the data that
supports student collaboration. you have collected or want to analyze.
Before students can upload data to the server, you The primary technique used to evaluate data in the
will need to register your detector as part of the performance study is a histogram of the number
cosmic ray investigations network. This is easily of events as a function of time over threshold
done on the teacher website. Registration will (TOT, see Chapter 2). In a very loose sense, TOT
require you to enter the serial number of the is a measure of the amount of energy deposited in
detector found on the bottom of the DAQ card the scintillator for a given event. Ideally, the DAQ
itself, or by typing the keyboard command “SN” board would have been equipped with an ADC
in the terminal emulator. (Analog-to-Digital Converter) to measure pulse
height and thus the energy deposited in the
By selecting the “Upload” link from the scintillator. To keep the cost down, however, a
<http://quarknet.fnal.gov/grid> page, you will TDC (Time to Digital Converter) was used. (See
seee instructions and links for uploading data. Chapter 2 for more on the TDC.). Since taller
(You do not need to worry about uploading data pulses (pulses with more energy) are generally
that may be “contaminated” by keyboard wider, there is a correlation between the time that
command lines typed during the operation of this the pulse exceeded the threshold value and the
run as the analysis software will create a new file amount of energy deposited in the scintillator.
for this data using only data lines that are the
complete 16 words across.)
Once you have uploaded data, to see that it
has been loaded successfully select the
“Data” link. You can “View” your data in
your school’s folder. The link to view this
data lists the date the data was collected. If a
29. Classroom Cosmic Ray Detector User’s Manual
Number of Events
Number of Events
Time over Threshold (ns) (ns)
Time over Threshold (ns)
a b
Figure 18. (a) The Gaussian distribution expected from an ‘ideal’ system performance
graph, (b) an actual system performance grph.
Figure 18(a)5 shows the ideal, Gaussian- traversing the counter. No real data histogram will
shaped distribution about a mean value for ever look perfectly Gaussian, but a shape
the time over threshold; Figure 18(b) shows somewhat resembling that of Figure 18(a) can be
an actual data run plot. a reasonable indicator that much of your data is
“good” and represents real muons.
The actual data run histogram peak does oc-
cur around 12 ns (which is typical for the One factor you can modify in plotting a histogram
1/2” thick scintillator, the PMT efficiency, is the number of bins into which the data are
and threshold settings used in our experi- divided. Choosing a different number of bins for
ment). This actual data, however, appears the same data set can significantly change the
more skewed than Gaussian. This histogram shape of the graph and may help evaluate the
may tell us that there is “good” data in our quality of the data.
actual run data, but that it is contaminated
with short pulses (a.k.a. noise) that were just
above threshold. Increasing the threshold Flux Experiments
value may “clean-up” this channel in the Cosmic ray flux, Φ CR , can be defined as
future.
There is probably a large portion of the actual run
events
data in Figure 18(b) that represents actual muons Φ CR = .
(time )(area )
Since the area of your detector will probably
5
Figure is used with permission. Eric W. Weisstein. not be varied in during an experiment, flux
quot;Gaussian Distribution.quot; From MathWorld--A Wolf- studies ask the question, “How does the rate
ram Web Resource. at which cosmic rays pass through my de-
http://mathworld.wolfram.com/GaussianDistribution.
html
tector depend on . . . ?” Since there are many
ways to complete this question, this study is
30. Classroom Cosmic Ray Detector User’s Manual
3
a fairly straightforward yet excellent open- time dilation. Chapter 1 discusses how the
ended research question for your students. lifetime measurement can be used to verify
time dilation. Here we develop the muon
Flux experiments may include several geo- lifetime measurement itself.
metries of your detectors such as (1) a single
counter, (2) multiple counters placed in the
same plane to increase detector area, (3)
closely stacked counters that require coinci-
dence, and (4) separated, stacked counters
that require coincidence used to look at flux
from only a particular direction of the sky. 1
There are several interesting variables to test 2
in flux studies. Have your students generate
the questions that they want to study.
In analyzing flux study data, students select
the data set and channel(s) to be analyzed. Figure20. A three counter muon lifetime de-
The analysis tools produce a histogram of tector system.
flux vs. time similar to the one shown in
Figure 19. Students can juxtapose data re- Consider Figure 20. When a muon enters a
garding their independent variable as a counter, a signal is generated in that counter.
function of time to look for correlations. If the muon traveled through counter 1 and
into counter 2, both of these counters should
have a signal at approximately the same
Muon Lifetime Experiments time. If the muon has stopped within counter
2, however, it will “wait around” until it de-
cays and generate a second signal in counter
2 upon decay. The time tDECAY, the time
between the two signals in counter 2, can be
extrapolated from the data file. Since no sig-
nal occurred in counter 3, this is a strong
indication that a muon did indeed decay in
counter 2.
Theory suggests that the muon lifetime ex-
hibits the characteristic exponential decay
that is common to other physical phenom-
ena, such as radioactive decay. In the case of
Figure19. Cosmic ray flux
(events/detector area/sec) vs. time graph
radioactive materials, the decay expression
over a period of two hours. is given by
t
−
A classic modern physics experiment is the N (t ) = N 0 e τ
measurement of the muon mean lifetime.
This experiment has historical significance
as the very first experimental evidence of
31. Classroom Cosmic Ray Detector User’s Manual
where N0 is the initial population, N(t) is the level should be set locally. Instead, coinci-
population after time t, and τ is the mean dence levels may be requested in the web
lifetime. The fact that muons in our experi- analysis. Students select the data file to be
ment do not coexist, whereas they do in ra- analyzed, the coincidence level, and the time
dioactive materials, does not change the de- interval between which coincidences must
cay expression. This does, however, give a have occurred. The lifetime can be deter-
slightly different meaning to N(t) and N0. In mined by fitting this decay plot with an ex-
this experiment, N0 is not the number of ponential decay function of the form de-
muons present at t = 0 but represents the to- scribed above. It is also possible for students
tal number of muons that were captured and to estimate the background value that should
decayed within the detector. N(t) is then the be subtracted from each bin before fitting.
number of these muons with tDECAY > t. This is also shown in Figure 21.
It should also be mentioned here that the
muon’s time of flight before it entered the Shower Studies
detector is of no concern. Though tDECAY is With the absolute time stamp that GPS of-
not its entire lifetime, plotting the number of fers, a network of detectors (at the same site,
decays as a function of decay time will yield or at different schools) can study cosmic ray
the same exponential decay shape from showers. The web analysis tools allow stu-
which lifetimes can be found. The common dents to make predictions about which di-
“zero time” that we use here is when each rection in the sky the shower (and thus the
muon entered the detector. If a large number primary cosmic ray) came from.
of decays are collected in the manner de-
scribed above, a plot can be produced using Students select the specific data sets to ana-
the web analysis tool similar to the one lyze (these may be from different locations),
shown in Figure 21. the coincidence level required, and the time
interval between which coincidences must
While doing a lifetime study, no coincidence have occurred. A 3-D plot of position on the
earth (xy) is graphed as a function of signal
time (z). This graph allows them to ‘see’ the
Muon Lifetime Decay Plot direction from which the shower came.
May 28, 2004
(ns)
Figure21. A lifetime graph showing number
Figure22. Shower study plot showing coinci-
of number of decays as a function decay
dences within a 70 ns time window.
from when the muon entered the scintilla-
tor. Fitting this data to an exponential de-
cay function can yield the lifetime.
32. Classroom Cosmic Ray Detector User’s Manual
Chapter 6: Advanced Topics
Plateauing Counters
In order to determine the operating voltage Noting the potentiometer reading on the
of each of your counters, it is necessary to bottom of the PMT base, perform a simple
perform a simple procedure in which you experiment to determine the singles rate for
“plateau the counter.” This step is necessary the channel that the counter is connected to
because counting variations due to drifts in using the method described on page 19.
the tube gain or voltage can occur during an Continue the process for many different
experiment. By using an operating voltage voltages (potentiometer settings) to produce
near the center of this plateau, these effects a graph similar to the one shown in Figure
are minimized. 23. Remember that the scalers increment in
hex format. Also, note that the channels are
numbered 1, 2, 3, and 4 on the board, num-
bered 0, 1, 2, and 3 respectively on the
How to Plateau a counter
monitor. This numbering scheme (starting
There are two methods to plateau a counter:
from 0 instead of 1) is consistent with engi-
1) Plateauing using a single counter
neering and computer programming prac-
2) Plateauing using multiple counters
tice.
The first technique is simpler, however, it
may make “seeing” the plateau more chal- Counter Plateau Plot
lenging. 100000
Singles Frequency
(counts/minute)
10000
1000
100
Plateauing Using a Single Counter 10
To plateau a single counter, choose a thresh- 1
4 4.5 5 5.5 6 6.5 7 7.5
old value for the discriminator and hold this Potentiometer Value
constant for your experiment. (Chapter 2 Figure23. Example of counter plateau graph
discusses how to choose a threshold value.) used to determine operating voltage of PMT.
Turn on the DAQ board and connect it to
your computer so that you can view the
The optimum operating voltage is where the
datastream on your monitor using a terminal
semi-log graph looks the most horizontal.
emulation program. (See Appendix C for
For the graph shown, this occurs around 5.5
help setting up a terminal emulation pro-
V. Sometimes it is difficult to “see” the pla-
gram.) Once you see the datastream, con-
teau with this technique. If multiple counters
vince yourself that lower potentiometer dial
are available, the technique outlined below
values result in a lower counting rate while
make the plateau more apparent.
higher settings produce a very high
datastream rate on your monitor.
33. Classroom Cosmic Ray Detector User’s Manual
Plateauing Using Multiple Counters Multiple Counter Plateau Plot
(Counter 2 is being plateaued)
Consider the three-counter setup in Figure
24. Let’s plateau counter 2. (This can occur 100
(1 & 2 / 1 & 3)
Coincidence
10
even if counters 1 and 3 have not been pla-
Frequency
1
teaued.) You can setup an experiment to in- 0.1
vestigate the coincidence frequency between 0.01
4 5 6 7
counters 1 & 2, 2 & 3, and 1 & 3 as a func- Potentiometer Value (for counter 2)
tion of the potentiometer setting on the base
of counter 2. (You may need to collect data Figure 25. Example of multiple counter
for these three coincidence sets during sepa- plateau graph used to determine operating
voltage of the PMT for counter 2.
rate runs unless you have a splitter for the
signal cables and a second DAQ board.)
Figure 25 shows that the “flattest” part of
the graph is near the potentiometer setting of
5.5. This value will serve as a reasonable
value at which to operate this counter.
1
Data Words
2 This section explains the meaning of each of
3
the data “words” that appear as a result of a
single event. It is not imperative for you to
understand these words in order to collect
and analyze data, but understanding these
words can help as you attempt to evaluate
Figure24. Shown here is a three-counter setup
used in plateauing a counter in order to deter-
the quality of your data.
mine the optimum operating tube voltage.
The datastream from the DAQ board is in
Since coincidences between 1 & 3 should be ASCII format. Each data line contains 16
relatively constant over the experiment, this words as shown are a sample set of data on
can serve as a baseline from which to com- the nest page in Figure 26. Words 1-9 are in
pare the 1 & 2 and/or 2 & 3 coincidences. A hex format. The data shown below is for a
single event—a single event can span sev-
1& 2
plot of vs. counter 2’s potentiometer eral lines of data!
1& 3
2&3
reading or a plot of vs. counter 2’s
1& 3
potentiometer reading produces a plateau
plot similar to that shown in Figure 25. You
can see that this plateau region is somewhat
“flatter” than was the case with the single
counter technique discussed above.
34. Classroom Cosmic Ray Detector User’s Manual
80EE0049 80 01 00 01 38 01 3C 01 7EB7491F 202133.242 080803 A 04 2 -0389
80EE004A 24 3D 25 01 00 01 00 01 7EB7491F 202133.242 080803 A 04 2 -0389
80EE004B 21 01 00 23 00 01 00 01 7EB7491F 202133.242 080803 A 04 2 -0389
80EE004C 01 2A 00 01 00 01 00 01 7EB7491F 202133.242 080803 A 04 2 -0389
80EE004D 00 01 00 01 00 39 32 2F 81331170 202133.242 080803 A 04 2 +0610
Figure26. A sample event containing five lines of data. Each line is comprised
of the same 16-word format with each word separated by a space.
Below is a brief description of each of the a new event; 0 = follow-up data of a trigger
“words.” event)
Word 1: A 32-bit trigger count of the 41.66 Word 3: TMC count of Falling Edge at in-
MHz CPLD clock mounted on the DAQ put 0 (FE0). The format used is shown be-
board with a range from low:
00000000...FFFFFFFF. Its resolution (1 bits 0-4 = TMC count of falling edge
LSB increment) is 24 ns.6,7 A trigger count bit 5 = channel edge tag (1 = valid falling
of 00000000 means that the DAQ card is edge, 0 = no falling edge)
still in the initialization phase, i.e., the GPS bits 6-7 = not used, always 0.
receiver has not started to generate 1PPS
pulses yet. Do not use the initial data until Word 4: TMC count of rising edge at input
the trigger count becomes non-zero! 1 (RE1); same format as RE0, except bit 7 is
always 0.
Word 2: TMC count of the Rising Edge at
input 0 (RE0). It is also the trigger tag. The Word 5: TMC count of falling edge at input
format used is shown below: 1 (FE1); same format as FE0.
bits 0-4 = TMC count of rising edge, reso-
lution = 0.75 ns (=24 ns/32) Word 6: TMC count of rising edge at input
bit 5 = channel edge tag (1 = valid rising 2 (RE2); same format as RE1.
edge, 0 = no rising edge)
bit 6 = not used, always 0 Word 7: TMC count of falling edge at input
bit 7 = trigger tag (1 = new trigger, start of 2 (FE2); same format as FE1.
6 Word 8: TMC count of rising edge at input
24.00 ns if the CPLD clock is exactly 41666666.67 Hz. The
actual CPLD frequency of each card is usually tuned within ±30
3 (RE3); same format as RE1.
Hz of the target frequency of 41666667 Hz. Generally, an Hz drift
from the target CPLD frequency result in accuracy errors of up to
n*24 ns. For example, a 30 Hz drift means that the accuracy time
Word 9: TMC count of falling edge at input
error has a range of ±720 ns if exactly 24.00 ns are assumed for a 3 (FE3); same format as FE1.
CPLD clock tick time. It is reasonable to assume that an error
within ±1000 ns is acceptable for a school network if the schools
are more than 1 mile apart from each other. Word 10: A 32-bit CPLD count of the most
7
recent 1PPS (1 pulse per second) time mark
The CPLD clock frequency fluctuates slightly over time, de-
from the GPS receiver. This hex word
pending on temperature changes and oscillator ageing drifts.
Therefore, in order to achieve high accuracy (±50 ns) in computing ranges from 00000000...FFFFFFFF and has
the absolute trigger times, you need to poll the current CPLD fre- a resolution of 24 ns just like word 1.8
quency at a regular basis (say once every 5 minutes) with com-
mand DG (Display GPS data). If the event rate is high enough (at
least 1 event per 100 seconds), the CPLD frequency can be com-
puted from the 1PPS counter numbers of consecutive events.
8
The same uncertainty comments apply here as in word 1.
35. Classroom Cosmic Ray Detector User’s Manual
Word 11: UTC time of most recent GPS re- 1 = GPS data possibly corrupted
ceiver data update. Although one update is while DAQ uC was/is busy.
sent each second, it is asynchronous with the bit 3: 0 = OK
1PPS pulse. The format used is shown be- 1 = Current or last 1PPS rate is not
low: within 41666666 ±50 CPLD
HHMMSS.mmm clock tick.s (This is a result of a
where: HH = hour [00...23] GPS glitch, the DAQ uC being
MM = minute [00...59] busy, or the CPLD oscillator not
SS = second [00...59] tuned correctly.)
mmm = millisecond [000...999]
Word 16: The time delay in milliseconds
Word 12: UTC date of most recent GPS re- between the 1PPS pulse and the GPS data
ceiver data update. The format used is interrupt. A positive number means 1PPS
shown below: pulse is ahead of GPS data, and negative
ddmmyy number means GPS data is ahead of 1PPS.
where: dd = day of month [01...31] To get the actual GPS time to the nearest
mm = month [01...12] second, round (word 11 + word 16/1000) to
yy = year [00...99] nearest full second. This gives the actual
e.g. 03=2003] GPS time at the last 1PPS pulse.
Word 13: A GPS valid/invalid flag. See Appendix F for the interpretation of the
A = valid (GPS data OK), data for the previous example.
V = invalid (insufficient satellite lock for 3-
D positioning, or GPS receiver is in ini-
tializing phase); time data might be OK Coincidence Counting Varia-
if number of GPS satellites is 3 or more
and previous GPS status was quot;Aquot; (valid)
tions
within the last minute.
Setting with Keyboard Commands
Word 14: The number of GPS satellites Chapter 4 discusses how to use some key-
visible for time and position information. board commands to read scaler values over a
This is a decimal number between 00…12. known period of time in an effort to deter-
mine basic counting rate. That simple cal-
Word 15: This hex word is a DAQ status culation does not discuss two parame-
flag. The format used is shown below: ters—gate window and TMC delay (d and w
bit 0: 0 = OK respectively). The gate window, d, refers to
1 = 1PPS interrupt pending (Warn- how close in time pulses must be to cause a
ing flag: If DAQ card is busy, trigger. The TMC delay, w, more difficult to
then 1PPS count might lag be- define, determines which pulse edges get
hind or get mismatched.) read out into the datastream when a trigger
bit 1: 0 = OK occurs, by delaying this information until
1 = trigger interrupt pending (pos- the trigger actually happens. (See Appendix
sibly high trigger rate; if con- E for a full explanation of each quantity and
tinues, then data might be cor- the details of time coincidence and data
rupted.) handling.)
bit 2: 0 = OK
36. Classroom Cosmic Ray Detector User’s Manual
Consider the actual physical quantities and Muon Lifetime Measurements
relate them to the two parameters, d and w. Set d = 2, and w = 401.
TTRG: This quantity is the maximum If you want to look for muons that stop and
time window during which real physics decay (2.2 µs mean lifetime) in a counter,
processes might cause a trigger. In other you look for the decay electron pulses sev-
words, if you set the card for 2-fold co- eral microseconds after the trigger, so you
incidences, and one channel receives a have TWIDTH = 400 (9600 ns, or about 10
signal at t = 0, at least one other channel µs).
must show a signal before t = TTRG or
you will not receive any information
about that pair of pulses. The examples Cosmic Ray Showers
in Appendix E may help. Set d = 50 (= 1.2 µs) and w = 100.
TWIDTH: This quantity is the duration In extensive air showers, the main “pan-
after the first pulse in a trigger during cake” of arriving particles should be be-
which you want to record all rising and tween 10 m and 200 m thick. The earliest
falling edge times. The channel in which and latest particles might arrive at the count-
these extra pulses occur does not matter; ers about 0.6 µs apart, for a vertical shower.
all of them will be saved. Thus you want TTRG to e about 1 µs. TWIDTH
can be about the same.
The physical quantities TTRG and TWIDTH are
the values for d and w you set on the board. However, you should not set huge time win-
You set TTRG and TWIDTH based on the type dows “just to be safe.” Doing this causes the
of experiment that you want to perform. card to be busy all the time, and its effective
Below is a list of several types of experi- dead time will become a serious problem.
ments and typical parameter values for each. The values of d and w should be as small as
possible for the given physics goals.
Muon Telescope Flux Experiments Default values, effective when the card is
Set d = 2, and w = 401. powered up, are d = 6 (= 144 ns) and w =
If you want to build a muon telescope with 10 (= 240 ns). Modifying these values is
counters less than a meter apart, TTRG is the probably unnecessary for muon telescope
time it takes a muon to go from the top experiments. However, for air shower de-
counter to the bottom counter. Since these tectors or muon lifetime experiments, you
muons travel at essentially the speed of light should set them at larger values. These val-
(≈ 1 ft/ns), the TTRG is only a few ns so you ues serve as a good guide. If you want to use
set d to the minimum value of 2 clock ticks, the values of d = 50 and w = 100, Table 3
or 48 ns. Similarly, to simply count muons, shows how to set the DAQ card to these
you are only interested in a short time win- values:
dow for edges, so you could take TWIDTH =
48 ns as well.
RE Resets the card by setting all counters to zero and return everything to de-
faults
CD Disables the counters and TMC
37. Classroom Cosmic Ray Detector User’s Manual
WT 01 00 Sets the time register with read pointer (register 01) = 00 and the write
WT 02 32 pointer (register 02) to d, in hexadecimal. The TMC delay d will be the dif-
ference of these values (so in fact you could set 01 to some value nn, and 02
to nn + d). This example sets d = 50. We have set register 02 to 32 = 50 . H 10
The maximum is 7F = 127 .
H 10
WC 00 1F Sets the coincidence level and enable desired channels. Set control reg-
isters with the WC (Write Control register) command. Register 0 sets the
coincidence level, using its first (left) hex character. Here, 0 means singles,
1 means 2-fold, and n-1 means n-fold coincidence level is to be required.
This is different from how coincidence is described in the data analysis
software found online. The second (right) hex character represents the de-
sired pattern of enabled/disabled channels in its bits, with 0s for disabled
channels and 1s for enabled channels. In this example, 1F means set 2-fold
coincidences with all 4 channels enabled: F = 1111. If you wanted to dis-
H
able channel 2 you would use 1101 = D . If you wanted to enable three-fold
H
coincidences with channel 2 turned off, you would use WC 00 2D.
WC 02 64 Sets the value of w (gate width). Registers 2 and 3 hold the gate width set-
WC 03 00 ting in integer clock ticks (units of 24 ns). The lower 8 bits of the binary
number representing w go in register 2, and the higher 8 bits in 3. Thus, the
desired gate width w is given as abcd and is typed as
WC 02 cd
WC 03 ab
As an example, to get w = 100 clock ticks (100 = 0064 = 0000 0000 0110
10 H
0100 ) you would type what is shown to the left.
2
CE Re-enables the onboard counters
DS Displays the scaler values
Table 3. A keyboard command sequence that allows for coincidence counting
variations of the gate window and TMC delay.
Interpreting Coincidence Data from has past, you type “DS,” the card will return
the DAQ Board the scaler values for each channel as dis-
This example shows how to interpret the cussed previously. In addition, the ‘@04’
coincidence data from the board. Assume line returns the value of the 2-fold coinci-
you are looking for 2-fold coincidence be- dences. This number is also in hexadecimal.
tween any two of the inputs. As discussed in The screen capture on the next page (Figure
the previous section, “WC 00 1F” will set up 27) illustrates these commands and outputs.
this 2-fold coincidence. If, after some time
38. Classroom Cosmic Ray Detector User’s Manual
RB—resets the scalers and TMC
WC 00 1F—sets up two fold coincidence between any
of the four channels
Board responds that coincidence is set as specified
DS—displays the scalers for channels 0-3 (@00
through @03), displays the number of coincidences
(@04) present for above defined criteria, displays the
1PPS signal (@5)
Figure27. A sample terminal emulation window displaying how to set coincidence
levels and how to read this coincidence data.
On-board Barometer Calibra- should be recorded every time the command
“BA” is typed on the keyboard. The ‘BA’
tion command displays a number that represents
You can measure air pressure with a ba- the ADC (analog-to-digital converter) count
rometer on the DAQ board. The barometer readout of the on-board barometer. Figure
sensor must be calibrated before it can yield 28 illustrates this command. Notice that the
pressure in units of kPa. To calibrate the value changes each time the “BA” command
sensor, you will need a real barometer (or is typed due to fluctuations in local air pres-
some way to retrieve actual pressure in the sure.
local area). The actual barometer reading
If you take actual barometer readings each sure), a graph similar to the one shown in
time the ADC count is recorded (over a pe- Figure 29 can be produced.
riod of significant fluctuation in air pres-
Figure28. The ADC count is displayed each time
the ‘BA’ command is typed.