Delikli civata cekme kapasitesi
•
0 likes•48 views
This document provides information on allowable tension forces for bolts according to DIN elastic design standards. It lists bolt hole and thread diameters, cross sectional areas, yield strengths, and allowable stresses to determine the maximum permissible tension forces P(1-1) on the bolt body and P(2-2) on the thread. Bolt diameters range from 10mm to 64mm. The yield strength is 6400kg/cm2 for 10mm bolts and 9000kg/cm2 for bolts 12mm and larger. Allowable stresses range from 2560kg/cm2 to 3600kg/cm2 depending on the bolt size.
Report
Share
Report
Share
Download to read offline
Recommended
Macron dynamics msa_r6s_specsheet
This document appears to be a technical drawing for an actuator part called the MSA-R6S. It includes dimensions, tolerances, materials, notes and specifications for the part. It also lists mounting hardware and indicates the drawing is subject to change without notice. A company called Macron Dynamics is identified as the owner and creator of the technical drawing.
Cilindro
The document describes calculations to determine the optimal radius and dimensions for a cylindrical container. It provides equations for the area of the walls and base of the cylinder given the radius. A graph shows the total area increasing with radius until reaching an optimal point around a radius of 23.040 units, which maximizes volume while minimizing surface area.
Campo de un conductor
This document contains data from an experiment measuring the magnetic field (B) generated by varying currents (I) running through a conductor. It lists the theoretical and measured B values along with the associated error percentages. Two graphs are shown, with the first graph fitting the data to a linear equation with an R^2 value of 0.975, and the second graph fitting the data to a linear equation with an R^2 value of 1.
Macron dynamics msa_r20_specsheet
This document appears to be engineering drawings for a Macron Rail Actuator model MSA-R20. It includes dimensions, tolerances, notes, and provides information on mounting features, shaft configurations, and other specifications. The drawings are proprietary and confidential property of Macron Dynamics Inc.
Macron dynamics msa_r15_specsheet
The document appears to be a technical drawing for a pulley assembly, specifying dimensions, tolerances, materials, and other details. Key information includes that it is for a Macron R15 rail actuator, with a double shafted pulley assembly and part number MSA-R15-B-AB. Dimensions and mounting features are provided across two pages of the technical drawing. The pulley assembly is to be used with Macron Dynamics rail actuators.
Resume
Ching-sun Ti is a 55-year-old Taiwanese woman who is 167 cm tall and weighs 57 kg. Her contact information includes her email, phone number during working hours from 9:00 to 21:00, and office address on the 3rd floor. She studied at National Taiwan University from 1990 to 1997 and earned a master's degree. Her work experience includes positions at various companies between 1997 and 2012 involving internet technology and management information systems. She is currently self-employed working from home.
Metodo estatico equivalente jessica garcia
This document discusses calculating seismic design forces for a building structure. It provides details on the building type, location, soil conditions, and calculates the base shear and lateral forces for each level. The following values are determined:
- Base shear of 315.36 tons
- Top force of 18.02 tons
- Lateral forces for each of 10 levels ranging from 66.22 tons to 1188.22 tons
USA DE MDSOLIS
The document contains load and shear force diagrams for a structural element. It lists the applied loads P1 of 1289.66 N and P2 of 3543.31 N acting downward, and the reactions Ay of 1514.47 N and By of 1648.54 N. It also lists the distributed loads w1 of 0.0981 N/mm acting downward and w2 of 23.93 N/mm acting upward. Graphs show the shear force and bending moment diagrams, with the shear force ranging from -362.77 to 203.90 kN and the moment ranging from -196.64 to 74.32 kN-mm.
Recommended
Macron dynamics msa_r6s_specsheet
This document appears to be a technical drawing for an actuator part called the MSA-R6S. It includes dimensions, tolerances, materials, notes and specifications for the part. It also lists mounting hardware and indicates the drawing is subject to change without notice. A company called Macron Dynamics is identified as the owner and creator of the technical drawing.
Cilindro
The document describes calculations to determine the optimal radius and dimensions for a cylindrical container. It provides equations for the area of the walls and base of the cylinder given the radius. A graph shows the total area increasing with radius until reaching an optimal point around a radius of 23.040 units, which maximizes volume while minimizing surface area.
Campo de un conductor
This document contains data from an experiment measuring the magnetic field (B) generated by varying currents (I) running through a conductor. It lists the theoretical and measured B values along with the associated error percentages. Two graphs are shown, with the first graph fitting the data to a linear equation with an R^2 value of 0.975, and the second graph fitting the data to a linear equation with an R^2 value of 1.
Macron dynamics msa_r20_specsheet
This document appears to be engineering drawings for a Macron Rail Actuator model MSA-R20. It includes dimensions, tolerances, notes, and provides information on mounting features, shaft configurations, and other specifications. The drawings are proprietary and confidential property of Macron Dynamics Inc.
Macron dynamics msa_r15_specsheet
The document appears to be a technical drawing for a pulley assembly, specifying dimensions, tolerances, materials, and other details. Key information includes that it is for a Macron R15 rail actuator, with a double shafted pulley assembly and part number MSA-R15-B-AB. Dimensions and mounting features are provided across two pages of the technical drawing. The pulley assembly is to be used with Macron Dynamics rail actuators.
Resume
Ching-sun Ti is a 55-year-old Taiwanese woman who is 167 cm tall and weighs 57 kg. Her contact information includes her email, phone number during working hours from 9:00 to 21:00, and office address on the 3rd floor. She studied at National Taiwan University from 1990 to 1997 and earned a master's degree. Her work experience includes positions at various companies between 1997 and 2012 involving internet technology and management information systems. She is currently self-employed working from home.
Metodo estatico equivalente jessica garcia
This document discusses calculating seismic design forces for a building structure. It provides details on the building type, location, soil conditions, and calculates the base shear and lateral forces for each level. The following values are determined:
- Base shear of 315.36 tons
- Top force of 18.02 tons
- Lateral forces for each of 10 levels ranging from 66.22 tons to 1188.22 tons
USA DE MDSOLIS
The document contains load and shear force diagrams for a structural element. It lists the applied loads P1 of 1289.66 N and P2 of 3543.31 N acting downward, and the reactions Ay of 1514.47 N and By of 1648.54 N. It also lists the distributed loads w1 of 0.0981 N/mm acting downward and w2 of 23.93 N/mm acting upward. Graphs show the shear force and bending moment diagrams, with the shear force ranging from -362.77 to 203.90 kN and the moment ranging from -196.64 to 74.32 kN-mm.
Lintech 100series specsheet
This document provides ordering information for 100 Series screw drives, including:
- Table and carriage configurations with number of bearings and lengths
- Screw, motor mount, coupling, encoder, and brake options
- Load and torque specifications for different screw diameters and numbers of bearings
- Dimensional drawings of table, carriage, and motor mount configurations
Lintech 120series specsheet
This document provides ordering and specification information for the 120 Series belt drive system. It includes details on ordering options like carriage length, travel length, drive shaft configuration, motor mounts, couplings, switches, encoders, and brakes. It also provides technical specifications for the 120 Series like load capacities, position accuracy, friction coefficient, dimensions, materials, and more. The document is intended to help customers properly order and understand the technical capabilities of the 120 Series belt drive system.
Portofolio jacket platform dynamic analysis
The document summarizes the dynamic analysis of the XYZ wellhead platform based on API RP2A WSD. It includes redesign details, main data used in the analysis such as soil properties, wave and earthquake information. It then covers the steps of the seismic, fatigue and load out analyses including determination of critical members. The maximum member and joint utilisation checks are reported. Load out analysis is also presented for the BOA BARGE 21/22 carrying containers. Final ballasting steps to achieve the desired draft are provided.
Micron gearbox dura_true_specsheet
This document provides specifications for True Planetary gearheads from Thomson Industries. It includes performance specifications, dimensions, load ratings and contact information for the manufacturer and distributor for the DuraTrue size 60, 90, and 115 gearhead models. The gearheads offer high precision, low backlash and easy mounting. They are available in a variety of ratios and specifications to suit different speed and load requirements.
Thong so hilti
This document provides specifications and load data for Hilti HST stud anchors. It includes:
- Descriptions of HST, HST-R, and HST-HCR anchors made of carbon steel, stainless steel, or high-corrosion resistant stainless steel.
- Tables with mean ultimate resistance, characteristic resistance, design resistance, and recommended load for various anchor sizes in tension and shear for non-cracked and cracked concrete.
- Details on installation equipment, setting operations, and mechanical properties of anchor bolts.
- An explanation of the detailed design method for tension and concrete capacity design method used to determine load values.
Fatigue Limit of SPD.pdf
The document summarizes research on evaluating the low-cycle fatigue durability of shear panel dampers (SPDs) used in bridges. Finite element analysis was used to investigate the influence of SPD dimensional parameters on crack initiation life and critical crack length. The analysis considered factors like weld toe radius, aspect ratio, and width-to-thickness ratio. Regression analysis was used to determine a relationship between critical crack length and these parameters. The research aims to also evaluate crack propagation life using the J-integral approach to calculate crack growth per cycle and determine the number of cycles until failure.
Strauto 2015
StrAuto is an automated structural design and optimization software. It provides an iterative design process to generate and evaluate thousands of design alternatives to find the optimal solution that meets design targets like lowest cost. It was used to optimize the design of several large-scale building projects. For one project, a super tall tower, StrAuto optimized the outrigger levels, concrete strengths, and core wall thicknesses, analyzing over 4,600 design variations to minimize weight and lateral drift within limits. This led to a 7.8% reduction in weight from the initial design.
Lintech 90series specsheet
This document provides ordering information for screw drive tables including:
- Carriage lengths of 6 and 12 inches
- Screw options ranging from 0.625 to 1 inch diameters
- Motor mount, coupling, limit switch, and encoder options
- Load capacity and specification details for the 6 and 12 inch carriages
It includes tables listing dimensions, weights and mounting details for each model number.
Autodesk robot structural analysis professional 2013
This document provides details of a fixed column base design connection between a column and concrete foundation. It includes the geometry, materials, and loads for the column, baseplate, anchors, concrete, and rebar. The document then provides the results of structural calculations to check the resistances of the connection to compression, tension, bending, pull-out, splitting, and other failure modes according to Eurocode standards. Key values calculated include the bearing resistance, anchor tensile resistance, base plate bending resistance, and column web tensile resistance.
Sachpazis: Steel member design in biaxial bending and axial compression examp...
This document provides a summary of the design of a steel member according to Eurocode 3. It includes:
- Details of the steel section being designed, including dimensions, material properties, and classification.
- Checks for shear, bending, axial compression, and buckling according to Eurocode 3, ensuring the design capacities exceed the design forces in each case.
- A summary of the design confirming the steel member meets all requirements for its intended loading based on the specifications in Eurocode 3.
Design and Manufacturing of Press Tools for Compressor Shell
The role of Sheet Metal has become very prominent with the use of Press Tools. It is one of the fundamental forms used in metalworking, and can be cut and bent into a variety of different shapes. Countless everyday objects are constructed of the material. Thicknesses can vary significantly, although extremely thin thicknesses are considered foil or leaf, and pieces thicker than 6 mm (0.25 in) are considered plate.The project deals with Compressor Shell Lower Housing. The Compressor Shell holds all the parts of the compressor in pre-defined location for the compressor to fool proof. The component should be freed from burrs and also to dimensional accurate. The outcome component is been inspected in the Quality department so as to check the Dimensional accuracy is been achieved.
Slab panel desing sheet (1) (2)
The document provides details of the design of a monolithic reinforced concrete slab. It includes the material properties, slab dimensions, load calculations, and reinforcement design for three slab panels. The slab thickness is selected as 150mm. Factored dead and live loads are calculated. Bending moments are calculated using provided coefficients increased by 25% per the reference standard. Minimum steel reinforcement is calculated and bar schedules are provided for flexural reinforcement.
SARNATH-PROFILE-CAE
The document provides details of various CAE projects completed by Sarnath for different clients. It lists 13 clients from various industries that Sarnath has worked with on FEA, CFD and other simulation projects. It then describes Sarnath's domain expertise which includes customization, FEA, CFD, structural design, lean manufacturing, product development and reverse engineering. Finally, it provides brief descriptions and details of 20 different CAE projects completed for various clients across industries.
Sachpazis Steel Member Analysis & Design (EN1993 1-1 2005)
Steel Member Analysis & Design, In accordance with EN1993-1-1:2005 incorporating Corrigenda February 2006 and April 2009 and the recommended values.
AS4100 Steel Design Webinar Worked Examples
Worked examples from the ClearCalcs AS4100 Steel Design Webinar - slides: https://www.slideshare.net/clearcalcs/steel-design-to-as4100-1998-a12016-webinar-clearcalcs
IRJET-Study on Behaviour of Retrofitted RC Beam-Column Exterior Joints with G...
This document presents a study on retrofitting reinforced concrete beam-column exterior joints with glass fiber reinforced polymer (GFRP) wrapping to improve their seismic performance. Three 1/5th scale specimens of a beam-column joint from a prototype 5-story building were tested: one unretrofitted control specimen and two specimens retrofitted with one or two layers of GFRP wrapping after being loaded to 70% of their ultimate capacity. Testing showed that the retrofitted specimens had increased load capacity, energy absorption, and ductility compared to the unretrofitted joint. Specifically, the single layer retrofitted joint was able to regain its original strength and had 60% more energy absorption than the control, while the double layer retrofitted
Lintech 130series specsheet
The document provides specifications for a 130 series screw drive table, including:
- Details on the number of bearings, carriage length, travel length, cover plates, screw and motor options.
- Dimensions for the table base, carriage, end plates and various mounting options.
- Load capacity, thrust force capacity, acceleration limits and other performance specifications.
- Contact information for the manufacturer, Electromate, is provided at the end.
Structural Design
This document provides design calculations for structural elements of a concrete car park structure according to BS-8110, including:
1. A one-way spanning roof slab with a span of 2.8m, designed as simply supported with 10mm main reinforcement bars at 300mm spacing and 8mm secondary bars.
2. A load distribution beam D and non-load bearing beam E, with calculations provided for beam D's dead and imposed loads.
3. Requirements include individual work submission by January 2nd, 2016 and assumptions to be clearly stated.
Bolt and weld_capacities
This document provides tables of tensile bolt capacities and weld capacities. The bolt capacity table lists bolt sizes from M10 to M36 with their cross-sectional area and single shear tensile capacity in kilonewtons. A second bolt table provides minimum shank tension and slip resistance. A weld table provides longitudinal and transverse capacities for various weld sizes from 3mm to 25mm. Notes provide information on ply thickness required for single shear bolt capacity and countersunk bolt head thickness additions.
Bolt and weld_capacities
This document provides tables of tensile bolt capacities and weld capacities. The bolt capacity table lists bolt sizes from M10 to M36 with their cross-sectional area and single shear tensile capacity. A second bolt table provides minimum shank tension and slip resistance. A weld table gives longitudinal and transverse capacities for various weld sizes. Notes provide information on ply thickness required for bolt shear capacity and adjusting ply thickness for countersunk bolt heads.
官方认证美国密歇根州立大学毕业证学位证书原版一模一样
原版一模一样【微信：741003700 】【美国密歇根州立大学毕业证学位证书】【微信：741003700 】学位证，留信认证（真实可查，永久存档）offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原海外各大学 Bachelor Diploma degree, Master Degree Diploma
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
More Related Content
Similar to Delikli civata cekme kapasitesi
Lintech 100series specsheet
This document provides ordering information for 100 Series screw drives, including:
- Table and carriage configurations with number of bearings and lengths
- Screw, motor mount, coupling, encoder, and brake options
- Load and torque specifications for different screw diameters and numbers of bearings
- Dimensional drawings of table, carriage, and motor mount configurations
Lintech 120series specsheet
This document provides ordering and specification information for the 120 Series belt drive system. It includes details on ordering options like carriage length, travel length, drive shaft configuration, motor mounts, couplings, switches, encoders, and brakes. It also provides technical specifications for the 120 Series like load capacities, position accuracy, friction coefficient, dimensions, materials, and more. The document is intended to help customers properly order and understand the technical capabilities of the 120 Series belt drive system.
Portofolio jacket platform dynamic analysis
The document summarizes the dynamic analysis of the XYZ wellhead platform based on API RP2A WSD. It includes redesign details, main data used in the analysis such as soil properties, wave and earthquake information. It then covers the steps of the seismic, fatigue and load out analyses including determination of critical members. The maximum member and joint utilisation checks are reported. Load out analysis is also presented for the BOA BARGE 21/22 carrying containers. Final ballasting steps to achieve the desired draft are provided.
Micron gearbox dura_true_specsheet
This document provides specifications for True Planetary gearheads from Thomson Industries. It includes performance specifications, dimensions, load ratings and contact information for the manufacturer and distributor for the DuraTrue size 60, 90, and 115 gearhead models. The gearheads offer high precision, low backlash and easy mounting. They are available in a variety of ratios and specifications to suit different speed and load requirements.
Thong so hilti
This document provides specifications and load data for Hilti HST stud anchors. It includes:
- Descriptions of HST, HST-R, and HST-HCR anchors made of carbon steel, stainless steel, or high-corrosion resistant stainless steel.
- Tables with mean ultimate resistance, characteristic resistance, design resistance, and recommended load for various anchor sizes in tension and shear for non-cracked and cracked concrete.
- Details on installation equipment, setting operations, and mechanical properties of anchor bolts.
- An explanation of the detailed design method for tension and concrete capacity design method used to determine load values.
Fatigue Limit of SPD.pdf
The document summarizes research on evaluating the low-cycle fatigue durability of shear panel dampers (SPDs) used in bridges. Finite element analysis was used to investigate the influence of SPD dimensional parameters on crack initiation life and critical crack length. The analysis considered factors like weld toe radius, aspect ratio, and width-to-thickness ratio. Regression analysis was used to determine a relationship between critical crack length and these parameters. The research aims to also evaluate crack propagation life using the J-integral approach to calculate crack growth per cycle and determine the number of cycles until failure.
Strauto 2015
StrAuto is an automated structural design and optimization software. It provides an iterative design process to generate and evaluate thousands of design alternatives to find the optimal solution that meets design targets like lowest cost. It was used to optimize the design of several large-scale building projects. For one project, a super tall tower, StrAuto optimized the outrigger levels, concrete strengths, and core wall thicknesses, analyzing over 4,600 design variations to minimize weight and lateral drift within limits. This led to a 7.8% reduction in weight from the initial design.
Lintech 90series specsheet
This document provides ordering information for screw drive tables including:
- Carriage lengths of 6 and 12 inches
- Screw options ranging from 0.625 to 1 inch diameters
- Motor mount, coupling, limit switch, and encoder options
- Load capacity and specification details for the 6 and 12 inch carriages
It includes tables listing dimensions, weights and mounting details for each model number.
Autodesk robot structural analysis professional 2013
This document provides details of a fixed column base design connection between a column and concrete foundation. It includes the geometry, materials, and loads for the column, baseplate, anchors, concrete, and rebar. The document then provides the results of structural calculations to check the resistances of the connection to compression, tension, bending, pull-out, splitting, and other failure modes according to Eurocode standards. Key values calculated include the bearing resistance, anchor tensile resistance, base plate bending resistance, and column web tensile resistance.
Sachpazis: Steel member design in biaxial bending and axial compression examp...
This document provides a summary of the design of a steel member according to Eurocode 3. It includes:
- Details of the steel section being designed, including dimensions, material properties, and classification.
- Checks for shear, bending, axial compression, and buckling according to Eurocode 3, ensuring the design capacities exceed the design forces in each case.
- A summary of the design confirming the steel member meets all requirements for its intended loading based on the specifications in Eurocode 3.
Design and Manufacturing of Press Tools for Compressor Shell
The role of Sheet Metal has become very prominent with the use of Press Tools. It is one of the fundamental forms used in metalworking, and can be cut and bent into a variety of different shapes. Countless everyday objects are constructed of the material. Thicknesses can vary significantly, although extremely thin thicknesses are considered foil or leaf, and pieces thicker than 6 mm (0.25 in) are considered plate.The project deals with Compressor Shell Lower Housing. The Compressor Shell holds all the parts of the compressor in pre-defined location for the compressor to fool proof. The component should be freed from burrs and also to dimensional accurate. The outcome component is been inspected in the Quality department so as to check the Dimensional accuracy is been achieved.
Slab panel desing sheet (1) (2)
The document provides details of the design of a monolithic reinforced concrete slab. It includes the material properties, slab dimensions, load calculations, and reinforcement design for three slab panels. The slab thickness is selected as 150mm. Factored dead and live loads are calculated. Bending moments are calculated using provided coefficients increased by 25% per the reference standard. Minimum steel reinforcement is calculated and bar schedules are provided for flexural reinforcement.
SARNATH-PROFILE-CAE
The document provides details of various CAE projects completed by Sarnath for different clients. It lists 13 clients from various industries that Sarnath has worked with on FEA, CFD and other simulation projects. It then describes Sarnath's domain expertise which includes customization, FEA, CFD, structural design, lean manufacturing, product development and reverse engineering. Finally, it provides brief descriptions and details of 20 different CAE projects completed for various clients across industries.
Sachpazis Steel Member Analysis & Design (EN1993 1-1 2005)
Steel Member Analysis & Design, In accordance with EN1993-1-1:2005 incorporating Corrigenda February 2006 and April 2009 and the recommended values.
AS4100 Steel Design Webinar Worked Examples
Worked examples from the ClearCalcs AS4100 Steel Design Webinar - slides: https://www.slideshare.net/clearcalcs/steel-design-to-as4100-1998-a12016-webinar-clearcalcs
IRJET-Study on Behaviour of Retrofitted RC Beam-Column Exterior Joints with G...
This document presents a study on retrofitting reinforced concrete beam-column exterior joints with glass fiber reinforced polymer (GFRP) wrapping to improve their seismic performance. Three 1/5th scale specimens of a beam-column joint from a prototype 5-story building were tested: one unretrofitted control specimen and two specimens retrofitted with one or two layers of GFRP wrapping after being loaded to 70% of their ultimate capacity. Testing showed that the retrofitted specimens had increased load capacity, energy absorption, and ductility compared to the unretrofitted joint. Specifically, the single layer retrofitted joint was able to regain its original strength and had 60% more energy absorption than the control, while the double layer retrofitted
Lintech 130series specsheet
The document provides specifications for a 130 series screw drive table, including:
- Details on the number of bearings, carriage length, travel length, cover plates, screw and motor options.
- Dimensions for the table base, carriage, end plates and various mounting options.
- Load capacity, thrust force capacity, acceleration limits and other performance specifications.
- Contact information for the manufacturer, Electromate, is provided at the end.
Structural Design
This document provides design calculations for structural elements of a concrete car park structure according to BS-8110, including:
1. A one-way spanning roof slab with a span of 2.8m, designed as simply supported with 10mm main reinforcement bars at 300mm spacing and 8mm secondary bars.
2. A load distribution beam D and non-load bearing beam E, with calculations provided for beam D's dead and imposed loads.
3. Requirements include individual work submission by January 2nd, 2016 and assumptions to be clearly stated.
Bolt and weld_capacities
This document provides tables of tensile bolt capacities and weld capacities. The bolt capacity table lists bolt sizes from M10 to M36 with their cross-sectional area and single shear tensile capacity in kilonewtons. A second bolt table provides minimum shank tension and slip resistance. A weld table provides longitudinal and transverse capacities for various weld sizes from 3mm to 25mm. Notes provide information on ply thickness required for single shear bolt capacity and countersunk bolt head thickness additions.
Bolt and weld_capacities
This document provides tables of tensile bolt capacities and weld capacities. The bolt capacity table lists bolt sizes from M10 to M36 with their cross-sectional area and single shear tensile capacity. A second bolt table provides minimum shank tension and slip resistance. A weld table gives longitudinal and transverse capacities for various weld sizes. Notes provide information on ply thickness required for bolt shear capacity and adjusting ply thickness for countersunk bolt heads.
Similar to Delikli civata cekme kapasitesi (20)
Autodesk robot structural analysis professional 2013
Autodesk robot structural analysis professional 2013
Sachpazis: Steel member design in biaxial bending and axial compression examp...
Sachpazis: Steel member design in biaxial bending and axial compression examp...
Design and Manufacturing of Press Tools for Compressor Shell
Design and Manufacturing of Press Tools for Compressor Shell
Sachpazis Steel Member Analysis & Design (EN1993 1-1 2005)
Sachpazis Steel Member Analysis & Design (EN1993 1-1 2005)
IRJET-Study on Behaviour of Retrofitted RC Beam-Column Exterior Joints with G...
IRJET-Study on Behaviour of Retrofitted RC Beam-Column Exterior Joints with G...
Recently uploaded
官方认证美国密歇根州立大学毕业证学位证书原版一模一样
原版一模一样【微信：741003700 】【美国密歇根州立大学毕业证学位证书】【微信：741003700 】学位证，留信认证（真实可查，永久存档）offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原海外各大学 Bachelor Diploma degree, Master Degree Diploma
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
5214-1693458878915-Unit 6 2023 to 2024 academic year assignment (AutoRecovere...
Bigdata of technology
ISPM 15 Heat Treated Wood Stamps and why your shipping must have one
For International shipping and maritime laws all wood must contain the ISPM 15 Stamp. Here is how and why.
Harnessing WebAssembly for Real-time Stateless Streaming Pipelines
Traditionally, dealing with real-time data pipelines has involved significant overhead, even for straightforward tasks like data transformation or masking. However, in this talk, we’ll venture into the dynamic realm of WebAssembly (WASM) and discover how it can revolutionize the creation of stateless streaming pipelines within a Kafka (Redpanda) broker. These pipelines are adept at managing low-latency, high-data-volume scenarios.
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressions
K8sGPT is a tool that analyzes and diagnoses Kubernetes clusters. This presentation was used to share the requirements and dependencies to deploy K8sGPT in a local environment.
Computational Engineering IITH Presentation
This Presentation will give you a brief idea about what Computational Engineering at IIT Hyderabad has to offer.
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODEL
As digital technology becomes more deeply embedded in power systems, protecting the communication
networks of Smart Grids (SG) has emerged as a critical concern. Distributed Network Protocol 3 (DNP3)
represents a multi-tiered application layer protocol extensively utilized in Supervisory Control and Data
Acquisition (SCADA)-based smart grids to facilitate real-time data gathering and control functionalities.
Robust Intrusion Detection Systems (IDS) are necessary for early threat detection and mitigation because
of the interconnection of these networks, which makes them vulnerable to a variety of cyberattacks. To
solve this issue, this paper develops a hybrid Deep Learning (DL) model specifically designed for intrusion
detection in smart grids. The proposed approach is a combination of the Convolutional Neural Network
(CNN) and the Long-Short-Term Memory algorithms (LSTM). We employed a recent intrusion detection
dataset (DNP3), which focuses on unauthorized commands and Denial of Service (DoS) cyberattacks, to
train and test our model. The results of our experiments show that our CNN-LSTM method is much better
at finding smart grid intrusions than other deep learning algorithms used for classification. In addition,
our proposed approach improves accuracy, precision, recall, and F1 score, achieving a high detection
accuracy rate of 99.50%.
New techniques for characterising damage in rock slopes.pdf
rock mass characterization and New techniques for characterising damage in rock slopes
A SYSTEMATIC RISK ASSESSMENT APPROACH FOR SECURING THE SMART IRRIGATION SYSTEMS
The smart irrigation system represents an innovative approach to optimize water usage in agricultural and landscaping practices. The integration of cutting-edge technologies, including sensors, actuators, and data analysis, empowers this system to provide accurate monitoring and control of irrigation processes by leveraging real-time environmental conditions. The main objective of a smart irrigation system is to optimize water efficiency, minimize expenses, and foster the adoption of sustainable water management methods. This paper conducts a systematic risk assessment by exploring the key components/assets and their functionalities in the smart irrigation system. The crucial role of sensors in gathering data on soil moisture, weather patterns, and plant well-being is emphasized in this system. These sensors enable intelligent decision-making in irrigation scheduling and water distribution, leading to enhanced water efficiency and sustainable water management practices. Actuators enable automated control of irrigation devices, ensuring precise and targeted water delivery to plants. Additionally, the paper addresses the potential threat and vulnerabilities associated with smart irrigation systems. It discusses limitations of the system, such as power constraints and computational capabilities, and calculates the potential security risks. The paper suggests possible risk treatment methods for effective secure system operation. In conclusion, the paper emphasizes the significant benefits of implementing smart irrigation systems, including improved water conservation, increased crop yield, and reduced environmental impact. Additionally, based on the security analysis conducted, the paper recommends the implementation of countermeasures and security approaches to address vulnerabilities and ensure the integrity and reliability of the system. By incorporating these measures, smart irrigation technology can revolutionize water management practices in agriculture, promoting sustainability, resource efficiency, and safeguarding against potential security threats.
学校原版美国波士顿大学毕业证学历学位证书原版一模一样
原版一模一样【微信：741003700 】【美国波士顿大学毕业证学历学位证书】【微信：741003700 】学位证，留信认证（真实可查，永久存档）offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原海外各大学 Bachelor Diploma degree, Master Degree Diploma
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
Embedded machine learning-based road conditions and driving behavior monitoring
Car accident rates have increased in recent years, resulting in losses in human lives, properties, and other financial costs. An embedded machine learning-based system is developed to address this critical issue. The system can monitor road conditions, detect driving patterns, and identify aggressive driving behaviors. The system is based on neural networks trained on a comprehensive dataset of driving events, driving styles, and road conditions. The system effectively detects potential risks and helps mitigate the frequency and impact of accidents. The primary goal is to ensure the safety of drivers and vehicles. Collecting data involved gathering information on three key road events: normal street and normal drive, speed bumps, circular yellow speed bumps, and three aggressive driving actions: sudden start, sudden stop, and sudden entry. The gathered data is processed and analyzed using a machine learning system designed for limited power and memory devices. The developed system resulted in 91.9% accuracy, 93.6% precision, and 92% recall. The achieved inference time on an Arduino Nano 33 BLE Sense with a 32-bit CPU running at 64 MHz is 34 ms and requires 2.6 kB peak RAM and 139.9 kB program flash memory, making it suitable for resource-constrained embedded systems.
Iron and Steel Technology Roadmap - Towards more sustainable steelmaking.pdf
Iron and Steel Technology towards Sustainable Steelmaking
Optimizing Gradle Builds - Gradle DPE Tour Berlin 2024
Sinan from the Delivery Hero mobile infrastructure engineering team shares a deep dive into performance acceleration with Gradle build cache optimizations. Sinan shares their journey into solving complex build-cache problems that affect Gradle builds. By understanding the challenges and solutions found in our journey, we aim to demonstrate the possibilities for faster builds. The case study reveals how overlapping outputs and cache misconfigurations led to significant increases in build times, especially as the project scaled up with numerous modules using Paparazzi tests. The journey from diagnosing to defeating cache issues offers invaluable lessons on maintaining cache integrity without sacrificing functionality.
22CYT12-Unit-V-E Waste and its Management.ppt
Introduction- e - waste – definition - sources of e-waste– hazardous substances in e-waste - effects of e-waste on environment and human health- need for e-waste management– e-waste handling rules - waste minimization techniques for managing e-waste – recycling of e-waste - disposal treatment methods of e- waste – mechanism of extraction of precious metal from leaching solution-global Scenario of E-waste – E-waste in India- case studies.
TIME DIVISION MULTIPLEXING TECHNIQUE FOR COMMUNICATION SYSTEM
Time Division Multiplexing (TDM) is a method of transmitting multiple signals over a single communication channel by dividing the signal into many segments, each having a very short duration of time. These time slots are then allocated to different data streams, allowing multiple signals to share the same transmission medium efficiently. TDM is widely used in telecommunications and data communication systems.
### How TDM Works
1. **Time Slots Allocation**: The core principle of TDM is to assign distinct time slots to each signal. During each time slot, the respective signal is transmitted, and then the process repeats cyclically. For example, if there are four signals to be transmitted, the TDM cycle will divide time into four slots, each assigned to one signal.
2. **Synchronization**: Synchronization is crucial in TDM systems to ensure that the signals are correctly aligned with their respective time slots. Both the transmitter and receiver must be synchronized to avoid any overlap or loss of data. This synchronization is typically maintained by a clock signal that ensures time slots are accurately aligned.
3. **Frame Structure**: TDM data is organized into frames, where each frame consists of a set of time slots. Each frame is repeated at regular intervals, ensuring continuous transmission of data streams. The frame structure helps in managing the data streams and maintaining the synchronization between the transmitter and receiver.
4. **Multiplexer and Demultiplexer**: At the transmitting end, a multiplexer combines multiple input signals into a single composite signal by assigning each signal to a specific time slot. At the receiving end, a demultiplexer separates the composite signal back into individual signals based on their respective time slots.
### Types of TDM
1. **Synchronous TDM**: In synchronous TDM, time slots are pre-assigned to each signal, regardless of whether the signal has data to transmit or not. This can lead to inefficiencies if some time slots remain empty due to the absence of data.
2. **Asynchronous TDM (or Statistical TDM)**: Asynchronous TDM addresses the inefficiencies of synchronous TDM by allocating time slots dynamically based on the presence of data. Time slots are assigned only when there is data to transmit, which optimizes the use of the communication channel.
### Applications of TDM
- **Telecommunications**: TDM is extensively used in telecommunication systems, such as in T1 and E1 lines, where multiple telephone calls are transmitted over a single line by assigning each call to a specific time slot.
- **Digital Audio and Video Broadcasting**: TDM is used in broadcasting systems to transmit multiple audio or video streams over a single channel, ensuring efficient use of bandwidth.
- **Computer Networks**: TDM is used in network protocols and systems to manage the transmission of data from multiple sources over a single network medium.
### Advantages of TDM
- **Efficient Use of Bandwidth**: TDM all
Unit-III-ELECTROCHEMICAL STORAGE DEVICES.ppt
Batteries -Introduction – Types of Batteries – discharging and charging of battery - characteristics of battery –battery rating- various tests on battery- – Primary battery: silver button cell- Secondary battery :Ni-Cd battery-modern battery: lithium ion battery-maintenance of batteries-choices of batteries for electric vehicle applications.
Fuel Cells: Introduction- importance and classification of fuel cells - description, principle, components, applications of fuel cells: H2-O2 fuel cell, alkaline fuel cell, molten carbonate fuel cell and direct methanol fuel cells.
Recently uploaded (20)
5214-1693458878915-Unit 6 2023 to 2024 academic year assignment (AutoRecovere...
5214-1693458878915-Unit 6 2023 to 2024 academic year assignment (AutoRecovere...
ISPM 15 Heat Treated Wood Stamps and why your shipping must have one
ISPM 15 Heat Treated Wood Stamps and why your shipping must have one
Harnessing WebAssembly for Real-time Stateless Streaming Pipelines
Harnessing WebAssembly for Real-time Stateless Streaming Pipelines
BPV-GUI-01-Guide-for-ASME-Review-Teams-(General)-10-10-2023.pdf
BPV-GUI-01-Guide-for-ASME-Review-Teams-(General)-10-10-2023.pdf
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressions
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressions
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODEL
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODEL
New techniques for characterising damage in rock slopes.pdf
New techniques for characterising damage in rock slopes.pdf
A SYSTEMATIC RISK ASSESSMENT APPROACH FOR SECURING THE SMART IRRIGATION SYSTEMS
A SYSTEMATIC RISK ASSESSMENT APPROACH FOR SECURING THE SMART IRRIGATION SYSTEMS
Embedded machine learning-based road conditions and driving behavior monitoring
Embedded machine learning-based road conditions and driving behavior monitoring
Iron and Steel Technology Roadmap - Towards more sustainable steelmaking.pdf
Iron and Steel Technology Roadmap - Towards more sustainable steelmaking.pdf
Optimizing Gradle Builds - Gradle DPE Tour Berlin 2024
Optimizing Gradle Builds - Gradle DPE Tour Berlin 2024
TIME DIVISION MULTIPLEXING TECHNIQUE FOR COMMUNICATION SYSTEM
TIME DIVISION MULTIPLEXING TECHNIQUE FOR COMMUNICATION SYSTEM
Delikli civata cekme kapasitesi
- 1. ALLOWABLE TENSION FORCES FOR THE BOLTS ( DIN - ELASTIC DESIGN ) BEARING CAPACITY OF BOLT BOLT HOLE THREAD CROSSECTION CROSSECTION CROSSECTION YIELD ALLOWABLE P (1-1) P (2-2) DIAMETER DIA. DIAMETER AREA ON AREA ON AREA ON STRENGTH STRESSES ON THE HOLE ON THE THREAD ( M ) o Dk BODY (Ab) THE HOLE THE THREAD ( 10.9 ) ( R ) D (mm) ( mm ) ( mm ) ( cm2 ) ( cm2 ) ( cm2 ) ( kg/cm2) ( kg/cm2) (ton) (ton) 10 2,5 8,052 0,785398 0,535398 0,509211 6400 2560 1,37 1,30 12 3 9,726 1,130973 0,770973 0,742948 9000 3600 2,78 2,67 16 3 13,402 2,010619 1,530619 1,410682 9000 3600 5,51 5,08 20 4 16,752 3,141593 2,341593 2,204059 9000 3600 8,43 7,93 24 4 20,102 4,523893 3,563893 3,173719 9000 3600 12,83 11,43 26 4 21,335 5,309292 4,269292 3,574993 9000 3600 15,37 12,87 27 4 23,102 5,725553 4,645553 4,191689 9000 3600 16,72 15,09 30 5 25,454 7,068583 5,568583 5,088643 9000 3600 20,05 18,32 33 5 28,454 8,552986 6,902986 6,358820 9000 3600 24,85 22,89 36 5 30,804 10,178760 8,378760 7,452536 9000 3600 30,16 26,83 39 5 33,804 11,945906 9,995906 8,974827 9000 3600 35,99 32,31 42 5 36,154 13,854424 11,754424 10,266031 9000 3600 42,32 36,96 48 5 41,504 18,095574 15,695574 13,529128 9000 3600 56,50 48,70 56 6 48,856 24,630086 21,270086 18,746737 9000 3600 76,57 67,49 64 6 56,206 32,169909 28,329909 24,811627 9000 3600 101,99 89,32