The document summarizes the control systems used in the JATCO CVT transmission found in some Jeep and Dodge vehicles. It describes the valve body and how the ratio control valve works to change gear ratios. It also discusses the electronic control module and how it uses various sensors and solenoids to control line pressures, variator pressures, and torque converter clutch operation. Diagnostic trouble codes related to CVT operation are provided at the end.
Developing Commercial Vehicles Inspired by NatureAltair
As Germany's largest independent engineering partner to the worldwide automotive industry, EDAG is continuously seeking for new technologies and innovative processes to streamline vehicle development. EDAG has a profound expertise in integrated development and the optimization of vehicles, production facilities, derivatives, and modules. To meet fuel efficiency and emission reduction goals, structurally efficient lightweight designs are demanded in the development of passenger cars and commercial vehicles alike. To fulfill customer demands and to deliver lighter and yet fully functional and validated components in shorter time, EDAG is leveraging its engineering knowledge to combine state-of-the-art computer aided engineering tools, in this case Altair's OptiStruct, with new production technologies such as additive manufacturing. OptiStruct enabled the EDAG engineers to design lightweight and, by being inspired by nature, yet stiff structures of a cabin and a chassis. The components were then manufactured using additive manufacturing methods. To find the optimal solution for the final design the engineers later also conducted multi-physical optimizations, combining strength and crash demands of the vehicle, using an equivalent linear approach. The entire development and manufacturing process for the cabin and chassis structures will be subject of this presentation, showing how a combination of topology optimization and additive manufacturing leads to lighter and stiffer products. The project is a prime example of how mature CAE technology can be adjusted and used in combination with new manufacturing methods to introduce revolutionary structural enhancements within the transportation sector.
Speakers
Andreas Pfeiffer, Development Engineer, EDAG
Three steps to design car seats at vehicle concept using digital human body models with Oscar and H-point to remain consistent with Federal laws and SAE recommended practicies.
Manual: 2005 and Newer - LS2 LS3 Drive By EFI Wiring Harness PSI Conversion
Specifically designed for complete wiring
harness for the fuel injection system on General Motors 2005 and newer- LS2/LS3 Gen IV fuel
injected engines with Drive By Cable Throttle Body and 4L60E or 4L80E transmission. If using a
58x Engine (LS3, etc) then a Lingenfelter Crank Signal Converter box (available through PSI) is
required so the 411 PCM (Red/Blue Connectors) can be utilized. The factory E38 or E67 controller
does not have the ability to operate a cable throttle body. If using a 24x LS2 no converter box is
required, however a 411 PCM (Red/Blue Connectors) is required.
This harness is constructed with GM Delphi Connectors and Terminals with GXL/TXL (600 volt
polyethylene cross-linked) wire which is professionally assembled and 100% quality inspected prior
to shipping. This harness includes all wiring that is needed by the PCM to run and control the fuel
injection system and transmission.
This is the first article I ever had published with Gears magazine. A controversial repair, but it's worked for years now.
Shown courtesy of Gears Magazine.
Developing Commercial Vehicles Inspired by NatureAltair
As Germany's largest independent engineering partner to the worldwide automotive industry, EDAG is continuously seeking for new technologies and innovative processes to streamline vehicle development. EDAG has a profound expertise in integrated development and the optimization of vehicles, production facilities, derivatives, and modules. To meet fuel efficiency and emission reduction goals, structurally efficient lightweight designs are demanded in the development of passenger cars and commercial vehicles alike. To fulfill customer demands and to deliver lighter and yet fully functional and validated components in shorter time, EDAG is leveraging its engineering knowledge to combine state-of-the-art computer aided engineering tools, in this case Altair's OptiStruct, with new production technologies such as additive manufacturing. OptiStruct enabled the EDAG engineers to design lightweight and, by being inspired by nature, yet stiff structures of a cabin and a chassis. The components were then manufactured using additive manufacturing methods. To find the optimal solution for the final design the engineers later also conducted multi-physical optimizations, combining strength and crash demands of the vehicle, using an equivalent linear approach. The entire development and manufacturing process for the cabin and chassis structures will be subject of this presentation, showing how a combination of topology optimization and additive manufacturing leads to lighter and stiffer products. The project is a prime example of how mature CAE technology can be adjusted and used in combination with new manufacturing methods to introduce revolutionary structural enhancements within the transportation sector.
Speakers
Andreas Pfeiffer, Development Engineer, EDAG
Three steps to design car seats at vehicle concept using digital human body models with Oscar and H-point to remain consistent with Federal laws and SAE recommended practicies.
Manual: 2005 and Newer - LS2 LS3 Drive By EFI Wiring Harness PSI Conversion
Specifically designed for complete wiring
harness for the fuel injection system on General Motors 2005 and newer- LS2/LS3 Gen IV fuel
injected engines with Drive By Cable Throttle Body and 4L60E or 4L80E transmission. If using a
58x Engine (LS3, etc) then a Lingenfelter Crank Signal Converter box (available through PSI) is
required so the 411 PCM (Red/Blue Connectors) can be utilized. The factory E38 or E67 controller
does not have the ability to operate a cable throttle body. If using a 24x LS2 no converter box is
required, however a 411 PCM (Red/Blue Connectors) is required.
This harness is constructed with GM Delphi Connectors and Terminals with GXL/TXL (600 volt
polyethylene cross-linked) wire which is professionally assembled and 100% quality inspected prior
to shipping. This harness includes all wiring that is needed by the PCM to run and control the fuel
injection system and transmission.
This is the first article I ever had published with Gears magazine. A controversial repair, but it's worked for years now.
Shown courtesy of Gears Magazine.
Affordable Stationery Printing Services in Jaipur | Navpack n PrintNavpack & Print
Looking for professional printing services in Jaipur? Navpack n Print offers high-quality and affordable stationery printing for all your business needs. Stand out with custom stationery designs and fast turnaround times. Contact us today for a quote!
[Note: This is a partial preview. To download this presentation, visit:
https://www.oeconsulting.com.sg/training-presentations]
Sustainability has become an increasingly critical topic as the world recognizes the need to protect our planet and its resources for future generations. Sustainability means meeting our current needs without compromising the ability of future generations to meet theirs. It involves long-term planning and consideration of the consequences of our actions. The goal is to create strategies that ensure the long-term viability of People, Planet, and Profit.
Leading companies such as Nike, Toyota, and Siemens are prioritizing sustainable innovation in their business models, setting an example for others to follow. In this Sustainability training presentation, you will learn key concepts, principles, and practices of sustainability applicable across industries. This training aims to create awareness and educate employees, senior executives, consultants, and other key stakeholders, including investors, policymakers, and supply chain partners, on the importance and implementation of sustainability.
LEARNING OBJECTIVES
1. Develop a comprehensive understanding of the fundamental principles and concepts that form the foundation of sustainability within corporate environments.
2. Explore the sustainability implementation model, focusing on effective measures and reporting strategies to track and communicate sustainability efforts.
3. Identify and define best practices and critical success factors essential for achieving sustainability goals within organizations.
CONTENTS
1. Introduction and Key Concepts of Sustainability
2. Principles and Practices of Sustainability
3. Measures and Reporting in Sustainability
4. Sustainability Implementation & Best Practices
To download the complete presentation, visit: https://www.oeconsulting.com.sg/training-presentations
Kseniya Leshchenko: Shared development support service model as the way to ma...Lviv Startup Club
Kseniya Leshchenko: Shared development support service model as the way to make small projects with small budgets profitable for the company (UA)
Kyiv PMDay 2024 Summer
Website – www.pmday.org
Youtube – https://www.youtube.com/startuplviv
FB – https://www.facebook.com/pmdayconference
Skye Residences | Extended Stay Residences Near Toronto Airportmarketingjdass
Experience unparalleled EXTENDED STAY and comfort at Skye Residences located just minutes from Toronto Airport. Discover sophisticated accommodations tailored for discerning travelers.
Website Link :
https://skyeresidences.com/
https://skyeresidences.com/about-us/
https://skyeresidences.com/gallery/
https://skyeresidences.com/rooms/
https://skyeresidences.com/near-by-attractions/
https://skyeresidences.com/commute/
https://skyeresidences.com/contact/
https://skyeresidences.com/queen-suite-with-sofa-bed/
https://skyeresidences.com/queen-suite-with-sofa-bed-and-balcony/
https://skyeresidences.com/queen-suite-with-sofa-bed-accessible/
https://skyeresidences.com/2-bedroom-deluxe-queen-suite-with-sofa-bed/
https://skyeresidences.com/2-bedroom-deluxe-king-queen-suite-with-sofa-bed/
https://skyeresidences.com/2-bedroom-deluxe-queen-suite-with-sofa-bed-accessible/
#Skye Residences Etobicoke, #Skye Residences Near Toronto Airport, #Skye Residences Toronto, #Skye Hotel Toronto, #Skye Hotel Near Toronto Airport, #Hotel Near Toronto Airport, #Near Toronto Airport Accommodation, #Suites Near Toronto Airport, #Etobicoke Suites Near Airport, #Hotel Near Toronto Pearson International Airport, #Toronto Airport Suite Rentals, #Pearson Airport Hotel Suites
RMD24 | Debunking the non-endemic revenue myth Marvin Vacquier Droop | First ...BBPMedia1
Marvin neemt je in deze presentatie mee in de voordelen van non-endemic advertising op retail media netwerken. Hij brengt ook de uitdagingen in beeld die de markt op dit moment heeft op het gebied van retail media voor niet-leveranciers.
Retail media wordt gezien als het nieuwe advertising-medium en ook mediabureaus richten massaal retail media-afdelingen op. Merken die niet in de betreffende winkel liggen staan ook nog niet in de rij om op de retail media netwerken te adverteren. Marvin belicht de uitdagingen die er zijn om echt aansluiting te vinden op die markt van non-endemic advertising.
Improving profitability for small businessBen Wann
In this comprehensive presentation, we will explore strategies and practical tips for enhancing profitability in small businesses. Tailored to meet the unique challenges faced by small enterprises, this session covers various aspects that directly impact the bottom line. Attendees will learn how to optimize operational efficiency, manage expenses, and increase revenue through innovative marketing and customer engagement techniques.
Premium MEAN Stack Development Solutions for Modern BusinessesSynapseIndia
Stay ahead of the curve with our premium MEAN Stack Development Solutions. Our expert developers utilize MongoDB, Express.js, AngularJS, and Node.js to create modern and responsive web applications. Trust us for cutting-edge solutions that drive your business growth and success.
Know more: https://www.synapseindia.com/technology/mean-stack-development-company.html
Enterprise Excellence is Inclusive Excellence.pdfKaiNexus
Enterprise excellence and inclusive excellence are closely linked, and real-world challenges have shown that both are essential to the success of any organization. To achieve enterprise excellence, organizations must focus on improving their operations and processes while creating an inclusive environment that engages everyone. In this interactive session, the facilitator will highlight commonly established business practices and how they limit our ability to engage everyone every day. More importantly, though, participants will likely gain increased awareness of what we can do differently to maximize enterprise excellence through deliberate inclusion.
What is Enterprise Excellence?
Enterprise Excellence is a holistic approach that's aimed at achieving world-class performance across all aspects of the organization.
What might I learn?
A way to engage all in creating Inclusive Excellence. Lessons from the US military and their parallels to the story of Harry Potter. How belt systems and CI teams can destroy inclusive practices. How leadership language invites people to the party. There are three things leaders can do to engage everyone every day: maximizing psychological safety to create environments where folks learn, contribute, and challenge the status quo.
Who might benefit? Anyone and everyone leading folks from the shop floor to top floor.
Dr. William Harvey is a seasoned Operations Leader with extensive experience in chemical processing, manufacturing, and operations management. At Michelman, he currently oversees multiple sites, leading teams in strategic planning and coaching/practicing continuous improvement. William is set to start his eighth year of teaching at the University of Cincinnati where he teaches marketing, finance, and management. William holds various certifications in change management, quality, leadership, operational excellence, team building, and DiSC, among others.
Falcon stands out as a top-tier P2P Invoice Discounting platform in India, bridging esteemed blue-chip companies and eager investors. Our goal is to transform the investment landscape in India by establishing a comprehensive destination for borrowers and investors with diverse profiles and needs, all while minimizing risk. What sets Falcon apart is the elimination of intermediaries such as commercial banks and depository institutions, allowing investors to enjoy higher yields.
What are the main advantages of using HR recruiter services.pdfHumanResourceDimensi1
HR recruiter services offer top talents to companies according to their specific needs. They handle all recruitment tasks from job posting to onboarding and help companies concentrate on their business growth. With their expertise and years of experience, they streamline the hiring process and save time and resources for the company.
1. JATCO CVT and
DaimlerChrysler by Sean Boyle
Part 2 Control Systems
Electronic and Computer
I n the last issue of GEARS,
we began looking at the
JATCO Continuously Variable
Transmission (CVT) being offered with
the 2007 Jeep Compass, Patriot, and
ratio to reduce engine RPM, the stepper
motor (1) moves out, which moves the
ratio control valve (2) out. This allows
line pressure to enter the primary varia-
tor (4). The additional pressure entering
Dodge Caliber. We examined its basic the primary variator causes the variator
construction, and discussed powerflow halves to squeeze together, causing the
through the unit. belt to ride toward the outer diameter
In this issue, we’re going to look (simulate large gear). Once the primary
into the electronics and control systems variator moves enough to satisfy the
used to operate this new transmission, TCM, the ratio control valve moves
beginning with the valve body. back into the hold position.
The position of the ratio control
Valve Body valve depends on the position of the
The JATCO CVT valve body variator and the stepper motor. The
consists of pressure sensors, variator TCM can alter the ratio by actuating
pressure solenoids, torque converter the stepper motor, letting the variator
clutch solenoids, and a unique stepper change until it moves the ratio control
motor for controlling the pressure split valve back into the hold position. This
between the primary and secondary is possible because these three compo- Figure 1: Ratio Hold Mode
variators. nents are linked together mechanically.
The stepper motor works (1) in The fluid release in the secondary
conjunction with the Ratio Control variator is controlled by the secondary
Valve and (2) as a mechanical link, pressure control solenoid and valve (3).
which connects the ratio control valve As this solenoid is actuated, the pres-
and stepper motor to the primary varia- sure trapped in the secondary variator
tor (4). (5) can either exhaust, or line pressure
The ratio control valve works in can be directed to it to increase the
three different modes: feed, hold, and clamping load. This is all controlled by
vent. These modes detemine the ulti- the TCM.
mate position of the variators and con- During the ratio change from low
trol the resulting ratios (Figure 1). to high, the secondary variator pres-
When the TCM is satisfied with sure exhausts to allow the ratio change.
the ratio and the position of the varia- Once the change is complete, line pres-
tors, the ratio control valve (2) is in the sure is once again directed into the
hold position. Line pressure from the secondary variator to provide clamping
pump is fed into the secondary variator load (Figure 3).
(5) to establish the necessary clamping When shifting from high to low
force on the belt (Figure 2). ratio, the TCM moves the stepper motor
When the TCM wants a higher in, which moves the ratio control valve Figure 2: Low to High Ratio
4 GEARS April 2007
4seanboylex2.indd 4 3/13/07 12:05:06 PM
2. Windings &
terminal
connections
impervious to
contamination
Plastic fully
encloses
lead wire
for support
Plastic fully
surrounds coil
Extended
Sure-Signal™tip
ensures stronger
signal
Part No. RE92888 Part No. RE92887
964 East Market St., Crawfordsville, IN 47933 • Toll Free: 800-729-7763 • Fax: 765-364-4576 • Email: raypt@raybestospowertrain.com
www.raybestospowertrain.com
raybestos407.indd 5 3/12/07 2:22:21 PM
3. JATCO CVT and DaimlerChrysler, Part 2
Figure 3: High to Low Ratio
Figure 6
1 Secondary Pulley Control
2 Clutch Reducing Regulator Valve
3 Lockup Control
4 Select Switch Valve
5 Select Control Valve
6 Solenoid Regulator Valve
Figure 4
into the vent position. The fluid in the
primary variator exhausts, which allows Figure 7
the sheaves to spread and allows the 1 Secondary Pulley Regulator
belt to ride toward its inner diameter. 2 Pressure Regulator 1
The secondary variator is still fed 3 Pressure Regulator 2
line pressure, which in turn causes it to 4 TCC Regulator Valve
5 Manual Valve
squeeze the sheaves together, making Figure 5
the belt ride toward its outer diameter.
The net result is a lower gear ratio. JATCO CVT has a few other very
Once the ratio has changed enough important valves.
to move the ratio control valve into Pressure regulator type valves: The
the hold positon, pressures are stabi- oil pump (Figure 4) has the ability to
lized between the primary and seconary generate over 1000 PSI, but not every-
variators. thing in the CVT needs this much
Obviously, this can happen at any pressure. Because 800+ PSI is more
speed and any engine RPM. The TCM than most circuits need, line pressure is
uses electical inputs, such as throttle regulated down to three lower levels.
position, manifold absolute pressure, 1) 218 PSI max for the clutches
fluid temperature, speed sensors (CKP, 2) 145 PSI max for the TCC Figure 8
ISS, OSS), pressure sensors, range sen- 3) 60 PSI max for the lube and
sor, etc., to determine the proper ratio. cooler circuits other pressures originate from line
So far we’ve looked primarily at The line pressure regulator valve pressure, which can vary between 72
the ratio control valve and the sec- (Figure 5) determines the overall high- and 870 PSI, depending on operating
ondary pressure control valve, but the est pressure in the transmission. All conditions. The pressure is controlled
6 GEARS April 2007
4seanboylex2.indd 6 3/13/07 12:05:32 PM
4. Figure 10
by the line pressure control solenoid,
which is pulse width modulated (PWM)
and high-side (B+) driven by the TCM.
Line pressure is fed directly to the ratio
control valve and the secondary valve
Figure 9 to influence ratios and belt side loads
1 TCC Lockup/Select Switch Solenoid 7 Stepper Motor (Figure 6).
2 TCC Control Solenoid 8 Ratio Control Valve The Valve body has a number of Screens
3 Secondary Pressure Solenoid 9 Ratio Control Link
and Valves (Figure 7 and 8).
4 Line Pressure Solenoid 10 ROM
5 Primary Pressure Sensor 11 Transmission Temperature Sensor The clutch reducing regulator valve low-
6 Secondary Pressure Sensor ers line pressure to 15 – 218 PSI to accomo-
date the forward and reverse clutches. These
pistons only need enough pressure to apply
adaquate force on the clutch packs to prevent
them from slipping.
When engaging drive or reverse, the
TCC/clutch control PWM solenoid modu-
lates to allow for smooth clutch apply. Once
the vehicle is in gear, the select switch/TCC
lockup solenoid allows the TCC/clutch control
PWM solenoid to modulate the torque con-
verter clutch apply and release.
The TCC/clutch control solenoid controls
the apply pressure to the torque converter
clutch. Once the TCC lockup control valve
shuttles to the apply position, apply pressure
regulated by the TCC/clutch control solenoid
enters the torque converter. The regulated
pressure allows for seamless application of
the torque converter clutch. The pressures in
the TCC apply circuit can vary between 0 to
145 PSI.
Unlike the Honda CVT, the JATCO CVT
uses a torque converter. The purpose of the
torque converter is to allow smooth accelera-
tion from a standstill by providing a hydraulic
disconnect from the engine. After rolling away
from a stop sign, the torque converter clutch
applies very early, usually at about 12 MPH.
Some of the advantages of a CVT include
increased efficiency of power transfer and
unlimited ratios, so the transmission control
module (TCM) makes the most from the CVT
by locking the converter as early as possible.
Figure 11
GEARS April 2007 7
4seanboylex2.indd 7 3/13/07 12:06:32 PM
5. JATCO CVT and DaimlerChrysler, Part 2
ety of DTCs will set tors and hydraulic system. The ROM
CASE CONNECTOR PINOUT depending on a circuit should never be interchanged with any
AND REFERENCE VALUES or mechanical failure other CVT. It is unique to the CVT it
with the line pressure came with. In fact, if you exchange a
Cav Color Function Measurements
1 DG/LB Line Press Sol PWM 3 – 9 ohms
solenoid: DTCs P0746, CVT while reusing the original TCM,
2 YL/DB Sec Press Sol PWM 3 – 9 ohms P0962, P0963. or swapping the original TCM with a
3 YL/LB TCC Sol PWM 3 – 9 ohms The Secondary used one, a “calibration mismatch” code
4 YL/GY TCC On/Off 10 – 15 ohms (a) Variator Pressure P167A will set. In that case, you’ll have
5 PK/LB 5-Volt Supply 5 volts
6 BK Ground
Control solenoid con- to use a factory scan tool to go through
7 PK/LB Sec Press Signal 0.7 – 3.5V (b) trols the position of a calibration procedure to recalibrate the
8 LB/YL Motor C 10 – 20 ohms the secondary variator TCM and ROM.
9 YL/OR Motor A 10 – 20 ohms pressure control valve. If you install a new TCM, a DTC
10 YL/WT Motor B 10 – 20 ohms
11 TN/YL Motor D 10 – 20 ohms
This valve regulates the P1679 “calibration not learned” will set,
16 YL/LB Chip Select for ROM release of fluid from which will also require a recalibration
17 RD/WT Trans Temp Signal 5k ohms at 75ºF the secondary variator using a scan tool. Regardless, it is impor-
18 DG/YL Primary Press Signal 0.7 – 3.5V (b) during movement from tant that the ROM assembly be kept with
19 DG/VT Sensor Ground
21 DG/BR Clock Select for ROM
high ratio to low ratio. its original transmission.
22 GY/YL Data In/Out for ROM Since the CVT relys on The Transmission connector (Figure
the secondary variator 10) has 22 pins but not all of the pins are
(a) Observed 26.5 ohms on training center bench unit to provide the neces- used. These JATCO CVT equipped vehi-
(b) Pressure transducers will output a varying voltage
based on pressure. Monitor pressure with a scan tool then
sary clamping force cles use the Controller Area Network
compare to actual pressure gauge readings. In neutral with on the belt, it’s very (CAN) heavily for module-to-module
the engine running, expect between 0.7 and 3.5 volts from important for this sole- communication (figure 11). The CAN
the primary, and around 1 volt from the secondary. noid and valve assem- is capable of sending up to 1 Mb/s of
bly to work properly. information across two wires, including
Electronics The following DTCs will set if vital sensor info such as TP, MAP, ECT,
The CVT has three PWM sole- there’s a failure in the Secondary Variator CKP, ect. When reviewing the TCM
noids: Line Pressure, Secondary Variator circuit or valve: DTC P0776, P0777, schematic, notice there are no dedicated
Pressure, and Torque Converter Clutch/ P0966, and P0967. The TCM will look circuits for engine speed, throttle posi-
Clutch Engagement. In addition to the at the secondary variator pressure sensor tion or load. The TCM relies on the CAN
PWM solenoids, the CVT has a single to determine if the solenoid is operating for these essential inputs.
on/off solenoid for the TCC lockup/ properly. If the actual and target pres- Since the CVT is only available in
select switch valve (Figure 9). sures don’t match, a DTC will set. new model vehicles that use the CAN
The line pressure PWM solenoid While reviewing the wiring sche- bus, it’s imperative that your scan tool
controls the position of the line pressure matic, you might notice the ROM assem- be CAN capable. The DaimlerChrysler
regulator based on TCM decisions. The bly. This is a chipset programmed when StarScan or StarMobile will undoubt-
typical resistance of the line pressure the transmission was assembled and edly have the most features available for
solenoid is between 3 – 9 ohms. A vari- carries vital information on the varia- diagnostics.
Here are diagnostic trouble codes related to the CVT:
DTC DESCRIPTION NOTES
P0219 Engine Overspeed Sets when CAN bus detects engine speed over 6800 RPM.
P0571 Brake Switch Sets if the brake switch status doesn't change but the computer registers
MPH. This needs to fail in two consecutive key cycles to set a DTC. Beware
two footed drivers.
P0602 Control Module Programming TCM doesn't receive valid vehicle info from FCM.
Error/Not Programmed
P0610 ECU Vehicle Options Mismatch Probably set from using a different module for the TCM. FCM/TIPM
P0641 Sensor Reference Voltage Circuit Pressure sensors have less than 0.05V. Open or short to ground in sensor
supply circuit.
P0707 Transmission Range Sensor Circuit Low Continuous loss of valid signal. Takes two failures to set a DTC.
P0708 Transmission Range Sensor Circuit High TCM receives more than two valid TR signals.
P0711 Transmission Temp Sensor Performance Trans temp doesn’t change for 10 minutes or the calculated vs. actual temp
varies by more than 104ºF.
P0712 Transmission Temp Sensor Low Scan tool indicates 356ºF. Short to ground, sensor failure, 68ºF = 2.5k – 6.5k
ohm, 176ºF = 300 – 900 ohms.
P0713 Transmission Temp Sensor High Scan tool indicates –40ºF. Short to power, open,
sensor failure.
8 GEARS April 2007
4seanboylex2.indd 8 3/13/07 12:07:29 PM
7. JATCO CVT and DaimlerChrysler, Part 2
DTC DESCRIPTION NOTES
P0716 ISS Circuit Performance All must be met for this DTC: • CKP-Pri RPM > 1000 RPM
• (Sec RPM x Est. Ratio) - Pri RPM > 1000 RPM
• (CKP-Sec RPM) x Est. Ratio < 1000 RPM
P0717 ISS Circuit No Signal If OSS DTC sets there might be an issue with power. Both sensors are
fed 12V from TIPM. Hall Effect: center terminal toggles 5V to ground.
P0721 OSS Circuit Performance All must be met for this DTC: • CKP-Pri RPM > 1000 RPM
• (Sec RPM x Est. Ratio) - Pri RPM > 1000RPM
• VSS - VSS Est. (using Sec RPM) ≥ 12.5 MPH
P0722 OSS No Signal If OSS DTC sets there might be an issue with power. Both sensors are fed 12V
from TIPM. Hall Effect: center terminal toggles 5V to ground.
P0730 Incorrect Gear Ratio Sets when a difference between actual and target ratio exceeds 1000 RPM for
5 seconds.
P0741 TCC Circuit Performance Excess TCC slip detected for 30 seconds. Takes two failures to set a DTC.
P0746 Line Pressure Solenoid Performance A ratio of 2.7:1 detected for 0.2 second or 3.5:1 detected for 0.1 second. This
would indicate a slipping belt.
P0776 Secondary Pressure Solenoid Stuck Off (High Difference between actual and target pressure is over 174 PSI for 30 sec-
Pressure) onds.
P0777 Secondary Pressure Solenoid Stuck On (Low Pressure) If actual is lower than target by 36 PSI for at least 1.5 seconds twice within a 30
second window, or if actual is 291 PSI less than target for 800 ms.
P0826 Up/Downshift Switch Circuit (Autostick Switches) Sets when the upshift and downshift switches are closed at the same time or
the switches are closed when the shifter isn't in drive.
P0842 Primary Oil Pressure Circuit Low Sets when voltage drops below 0.09V for 5 seconds.
P0843 Primary Oil Pressure Circuit High Sets when voltage rises above 4.7V for 5 seconds.
P0847 Secondary Oil Pressure Sensor Low Sets when voltage drops below 0.09V for 5 seconds.
P0848 Secondary Oil Pressure Sensor High Sets when voltage rises above 4.7V for 5 seconds.
P0962 Pressure Control Solenoid A Circuit Low (Line Press Check for short to ground and lack of power output from TCM. High side driv-
Solenoid) ers in the TCM.
P0963 Pressure Control Solenoid A Circuit High (Line Pressure Check for opens and high resistance. TCM monitors current flow.
Solenoid)
P0966 Pressure Control Solenoid B Circuit Low (Secondary Check for short to ground and lack of power output from TCM. High side driv-
Pressure Solenoid) ers in the TCM.
P0967 Pressure Control Solenoid B Circuit High Check for opens and high resistance. TCM monitors current flow.
(Secondary Pressure Solenoid)
P161B Battery Disconnect/TCM Internal Sets with a loss of power to the TCM.
P1661 Sensor Ground Reference High Check for opens or short to B+ on the sensor ground circuit.
P1679 Calibration Not Learned New TCM installed.
P167A Calibration Mismatch Swapping TCMs or Transmissions.
P1702 Primary Oil Pressure Sensor/Secondary Oil Pressure Comparison between valid signals between the two sensors.
Correlation
P1723 Lockup/Select Control Circuit Invalid electrical voltages.
P1729 Transmission Ratio Control Circuit (Stepper Motor) Invalid electrical voltages.
P2769 TCC Circuit Low Check for short to ground and lack of power output from TCM. High side driv-
ers in the TCM.
P2770 TCC Circuit High Check for opens and high resistance.
U0001 CAN C Bus Communication network problem. Might not get communication with scan tool
if the problem is present.
U0100 Lost Communication with PCM Check connections and see if other modules can communicate.
U0121 Lost Communication with ABS Check connections and see if other modules can communicate.
U0141 Lost Communication with IPM (FCM/TIPM) Check connections and see if other modules can communicate.
Although it may be a while before even eight speed transmissions are roll- market right now, including weight,
you see one of these CVTs in your ing off the assembly line every day, but torque capacity, and ratio-change speed.
shop, it’s definitely time to get ready they’ll never achieve the infinite num- And at the rate technology is increasing,
for this technology. CVTs could very ber of ratios found with a CVT. don’t be surprised to see these issues
well be the next trend for the automatic With that said, there are a few addressed very soon.
transmission industry. Six, seven, and things holding back a widespread CVT
10 GEARS April 2007
4seanboylex2.indd 10 3/13/07 12:08:00 PM
8. It’s a tough decision.
Take your time.
Our Kits. Their Kits.
1. Better Parts 1. Price
Nobody makes transmission parts more
dependable. Freudenberg-NOK’s Technology
Center houses 70 engineering and materials
professionals that have developed hundreds
of patents and proprietary compounds
that improve gasket and seal performance. Our globally
integrated supply of products from
85 automotive operations in 27
countries insures that we produce
the best gaskets and seals.
2. More Parts.
We offer more parts and sell more parts than any other kit sup-
plier. Every 12.7 seconds someone, somewhere,
rebuilds a transmission with a TransTec® kit.
That’s 24 hours a day, 7 days a week, 365 days a
year... and that doesn’t even include our O.E.
service kits.
3. History of Satisfied Customers
The companies that formed to bring you TransTec® kits have a
long history of serving satisfied customers. In fact,
we’ve been an O.E. supplier as long as there
have been cars!
4. Lowest Overall Cost
Add it all up and you’ll find TransTec®
kits have the lowest overall cost. Better
parts and better performance means
less chance of a comeback. Get it all with
TransTec® kits from Freudenberg-NOK,
the O.E. supplier with aftermarket vision.
T: 419.499.2502 • F: 419.499.3337
www.TransTec.com • Milan, OH 44846
transtec407plcd.indd 11 3/13/07 12:40:28 PM