1. The document provides assembly instructions for a transmission and torque converter for wheel loader models 924G and 924Gz.
2. It lists required tools and parts and provides detailed steps and illustrations for assembling various transmission components like bearings, seals, gears, clutches, and shafts.
3. Cleanliness is important during assembly and inspect all parts for wear or damage before installing. Lubricate parts as specified and use locking compounds and sealants where indicated.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix AAN) Service Repair Manua...9fikslkddmd8u
This document provides assembly instructions for a power shift transmission in a 924G wheel loader. It outlines 56 steps to assemble the transmission components, including installing bearings and seals, assembling various clutch packs, and attaching housing components. Tools required include presses, heaters, installers, and sealants. Proper cleaning and lubrication of parts is emphasized. Torque specifications are provided for housing bolts.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix 3PZ) Service Repair Manua...9fikslkddmd8u
This document provides instructions for assembling the power shift transmission for 924G and 924Gz wheel loaders. It outlines 54 steps to assemble the various components, including installing gears, bearings, seals, pistons, springs, plates, discs, hubs and other parts. Tools required are listed. Cleanliness is important during assembly to prevent contamination. Torque specifications are provided for certain fasteners. References are made to other documents for specifications on components like clutch discs and procedures to measure running clearances.
This document provides instructions for servicing a 924K wheel loader. It lists 66 steps to disassemble and reassemble components of the transmission, including installing seals, bearings, sensors, shafts and housing components. Precise torques and tools are specified. Safety precautions are noted for installing spring-loaded parts.
This document provides instructions for assembling the transmission and torque converter of a 924H wheel loader. It lists required tools and gives step-by-step instructions with illustrations. Some key steps include installing bearings and seals, assembling various clutch packs using special tools to compress springs, and ensuring proper end play and lubrication during assembly. Cleanliness and heating/cooling parts as needed during assembly is emphasized to avoid damage.
This document provides assembly instructions for a transmission and torque converter in a wheel loader. It lists required tools and parts and provides step-by-step instructions with illustrations. The instructions involve assembling bearings, seals, gears, clutches, shafts and other components in a precise order while maintaining cleanliness and lubrication. Special tools and heating/cooling of some parts is required to properly assemble the transmission.
This document provides instructions for assembling the transmission and torque converter of a 924H wheel loader. It lists required tools and gives step-by-step instructions with illustrations. Some key steps include installing bearings and seals, assembling various clutch packs using specialized tools to compress springs, and ensuring proper end play and lubrication during assembly. Cleanliness and heating/cooling parts as needed during assembly is emphasized to avoid damage.
This document provides instructions for assembling the transmission and torque converter of a 924H wheel loader. It lists required tools and gives step-by-step instructions with illustrations. Some key steps include installing bearings and seals, assembling various clutch packs using specialized tools, and ensuring proper end play and lubrication during assembly. Cleanliness and heating/cooling parts as needed during assembly is emphasized to avoid damage.
This document provides assembly instructions for a transmission and torque converter in a wheel loader. It lists required tools and parts and provides step-by-step instructions with illustrations. The instructions include installing bearings and seals, assembling clutch packs, installing gears and shafts, and setting end play. Cleanliness is emphasized and inspecting components for wear or damage before assembly is noted.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix AAN) Service Repair Manua...9fikslkddmd8u
This document provides assembly instructions for a power shift transmission in a 924G wheel loader. It outlines 56 steps to assemble the transmission components, including installing bearings and seals, assembling various clutch packs, and attaching housing components. Tools required include presses, heaters, installers, and sealants. Proper cleaning and lubrication of parts is emphasized. Torque specifications are provided for housing bolts.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix 3PZ) Service Repair Manua...9fikslkddmd8u
This document provides instructions for assembling the power shift transmission for 924G and 924Gz wheel loaders. It outlines 54 steps to assemble the various components, including installing gears, bearings, seals, pistons, springs, plates, discs, hubs and other parts. Tools required are listed. Cleanliness is important during assembly to prevent contamination. Torque specifications are provided for certain fasteners. References are made to other documents for specifications on components like clutch discs and procedures to measure running clearances.
This document provides instructions for servicing a 924K wheel loader. It lists 66 steps to disassemble and reassemble components of the transmission, including installing seals, bearings, sensors, shafts and housing components. Precise torques and tools are specified. Safety precautions are noted for installing spring-loaded parts.
This document provides instructions for assembling the transmission and torque converter of a 924H wheel loader. It lists required tools and gives step-by-step instructions with illustrations. Some key steps include installing bearings and seals, assembling various clutch packs using special tools to compress springs, and ensuring proper end play and lubrication during assembly. Cleanliness and heating/cooling parts as needed during assembly is emphasized to avoid damage.
This document provides assembly instructions for a transmission and torque converter in a wheel loader. It lists required tools and parts and provides step-by-step instructions with illustrations. The instructions involve assembling bearings, seals, gears, clutches, shafts and other components in a precise order while maintaining cleanliness and lubrication. Special tools and heating/cooling of some parts is required to properly assemble the transmission.
This document provides instructions for assembling the transmission and torque converter of a 924H wheel loader. It lists required tools and gives step-by-step instructions with illustrations. Some key steps include installing bearings and seals, assembling various clutch packs using specialized tools to compress springs, and ensuring proper end play and lubrication during assembly. Cleanliness and heating/cooling parts as needed during assembly is emphasized to avoid damage.
This document provides instructions for assembling the transmission and torque converter of a 924H wheel loader. It lists required tools and gives step-by-step instructions with illustrations. Some key steps include installing bearings and seals, assembling various clutch packs using specialized tools, and ensuring proper end play and lubrication during assembly. Cleanliness and heating/cooling parts as needed during assembly is emphasized to avoid damage.
This document provides assembly instructions for a transmission and torque converter in a wheel loader. It lists required tools and parts and provides step-by-step instructions with illustrations. The instructions include installing bearings and seals, assembling clutch packs, installing gears and shafts, and setting end play. Cleanliness is emphasized and inspecting components for wear or damage before assembly is noted.
Caterpillar cat 992 k wheel loader (prefix zmx) service repair manual (zmx000...fjjskkdmnsme
This document provides assembly instructions for a torque converter used in a 992K wheel loader. It lists over 40 steps and references various tools and components. Key steps include installing seals and bearings onto shafts, positioning carrier and gear assemblies weighing up to 57kg, and checking bearing end play using dial indicators to ensure proper clearance of 0.10±0.05mm. The overall process assembles the various internal components of the torque converter in the correct order.
Caterpillar cat 992 k wheel loader (prefix zmx) service repair manual (zmx000...fjjskqweekfsmem
This document provides assembly instructions for a torque converter used in a 992K wheel loader. It lists over 60 steps and accompanying illustrations to assemble the various components of the torque converter in the proper order. Key components include seals, bearings, gears, plates, pistons, discs, sleeves, and housings. Special tools and lifting devices are required due to the large size and weights of components, which range from 25-680 kg. Proper temperatures and torques are specified for a safe and accurate reassembly of the torque converter.
Caterpillar cat 992 k wheel loader (prefix zmx) service repair manual (zmx000...fudjsjfekskkem
This document provides assembly instructions for a torque converter used in a 992K wheel loader. It lists over 60 steps and accompanying illustrations to assemble the various components of the torque converter in the proper order. Key components include seals, bearings, gears, plates, pistons, discs, sleeves, and housings. Special tools and lifting devices are required due to the large size and weights of components, which range from 25-680 kg. Proper temperatures and torques are specified for a safe and accurate reassembly of the torque converter.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, seals, gears, discs, plates, pistons, housings and other components. Proper cleaning, lubrication, and use of installation tools are emphasized.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a planetary transmission used in a 972H wheel loader. It describes how to assemble the input shaft, carrier assemblies, clutch components, output shaft, and other parts. Detailed steps and illustrations are provided to guide technicians through the assembly process. Cleanliness is emphasized and special tools are required to properly install some components like bearings. The assembly involves over 40 individual steps and requires lifting heavy parts into place.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections detailing the assembly of the transmission's planetary gear sets and clutches. The summary includes:
1) Cleaning and preparing transmission components before assembly.
2) Assembling the three planetary gear sets which include installing bearings, gears, shafts, seals and retaining rings.
3) Installing clutches which involve alternating friction discs and plates, installing seals, pistons and springs.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, gears, seals, springs, and other components. Proper cleaning and use of installation tools are noted.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, gears, seals, springs, and other components. Proper cleaning and use of installation tools are emphasized.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, gears, seals, springs, and other components. Proper cleaning and use of installation tools are emphasized.
This document provides assembly instructions for a 992K wheel loader torque converter. It lists over 60 steps and required tools to assemble the various components of the torque converter. Key parts that are assembled include the shaft assembly, carrier assembly, gears, housing assembly, impeller clutch, turbine assembly, clutch housing assembly, and pump adapters. Lifting devices and special tools are required due to the heavy weights of components like the housing assembly and impeller clutch.
This document provides assembly instructions for a torque converter in a 992K wheel loader. It lists over 40 steps and required tools to assemble internal components like seals, bearings, gears, and housings. Proper lifting equipment is needed due to component weights up to 590kg. Tolerances and torque specifications are provided.
This document provides assembly instructions for a 992K wheel loader torque converter. It lists over 60 steps and required tools to assemble the various components of the torque converter. Key parts that are assembled include the shaft assembly, carrier assembly, gears, housing assembly, impeller clutch, turbine assembly, clutch housing assembly, and pump adapters. Lifting devices and special tools are required due to the heavy weights of components like the housing assembly and impeller clutch.
Caterpillar Cat CP-663E Vibratory Compactor (Prefix AEF) Service Repair Manua...ujkfdkkmsmd
This document provides disassembly and assembly instructions for a piston pump used in vibratory compactors. It describes 41 steps to fully disassemble the pump into individual components. This includes removing seals, springs, valves, pistons, plates, blocks, bearings and other parts. Similarly, it lists 41 steps for reassembling all the components in the reverse order. Cleanliness is emphasized throughout the process.
Caterpillar Cat CP-583E Vibratory Compactor (Prefix CNX) Service Repair Manua...ujkfdkkmsmd
This document provides instructions for removing and installing piston cooling jets, pistons, connecting rods, and related components on a Caterpillar 3056E engine. The removal process involves taking out the engine oil pan, removing valve assemblies from the piston cooling jets, and pushing pistons and connecting rods out of the cylinder block. The installation process requires cleaning components, lubricating them with oil, and reinserting pistons and connecting rods into the cylinder block before replacing other parts. Safety notices are provided to keep components clean and contain fluids.
Caterpillar Cat CP-573E Vibratory Compactor (Prefix CEB) Service Repair Manua...ujkfdkkmsmd
The document provides instructions for removing and installing the final drive planetary and piston motor components on a CS-573E and CP-573E vibratory compactor. It describes using various tools to disassemble components like the housing, hub, gears, seals and installing new components in the reverse order. Precise torques and clear illustrations are provided to correctly assemble the final drive planetary.
Caterpillar Cat CP-563D Vibratory Compactors (Prefix 2RZ) Service Repair Manu...ujkfdkkmsmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on CP-563D and CS-563D vibratory compactors powered by a 3116 engine. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure refers to ensuring parts are clean and checking guidelines for determining if valve seats can be reused.
Caterpillar Cat CP-533E Vibratory Compactor (Prefix ASL) Service Repair Manua...ujkfdkkmsmd
This document provides instructions for disassembling and assembling the piston pump used for drum propulsion on vibratory compactor models CS-533E and CP-533E. The disassembly procedure involves removing 28 components from the pump in 12 steps using various tools. Cleaning and inspecting parts is emphasized before reassembly in the reverse order over 28 steps.
Caterpillar Cat CP-533D Vibratory Compactor (Prefix AET) Service Repair Manua...ujkfdkkmsmd
This document provides instructions for removing and installing inlet and exhaust valve guides on a CS-533D and CP-533D vibratory compactor. It outlines the required tools and gives step-by-step instructions for removing the old guides and pressing new guides into the cylinder head assembly. Proper cleaning and lubrication of parts is emphasized to prevent premature wear. Reusability guidelines for different components are also referenced.
Caterpillar Cat CP-433E Vibratory Compactor (Prefix DAC) Service Repair Manua...ujkfdkkmsmd
The document provides instructions for assembling and disassembling various components of a vibratory compactor model CS-433E or CP-433E, including:
- Assembling the piston motor drum propel system in 24 steps requiring various tools.
- Installing the assembled piston motor drum propel system with 2 illustrations.
- Removing the final drive planetary from the drum propel in 7 steps requiring lifting tools and draining the oil first.
More Related Content
Similar to Caterpillar Cat 924Gz Wheel Loader (Prefix WMB) Service Repair Manual (WMB00001 and up).pdf
Caterpillar cat 992 k wheel loader (prefix zmx) service repair manual (zmx000...fjjskkdmnsme
This document provides assembly instructions for a torque converter used in a 992K wheel loader. It lists over 40 steps and references various tools and components. Key steps include installing seals and bearings onto shafts, positioning carrier and gear assemblies weighing up to 57kg, and checking bearing end play using dial indicators to ensure proper clearance of 0.10±0.05mm. The overall process assembles the various internal components of the torque converter in the correct order.
Caterpillar cat 992 k wheel loader (prefix zmx) service repair manual (zmx000...fjjskqweekfsmem
This document provides assembly instructions for a torque converter used in a 992K wheel loader. It lists over 60 steps and accompanying illustrations to assemble the various components of the torque converter in the proper order. Key components include seals, bearings, gears, plates, pistons, discs, sleeves, and housings. Special tools and lifting devices are required due to the large size and weights of components, which range from 25-680 kg. Proper temperatures and torques are specified for a safe and accurate reassembly of the torque converter.
Caterpillar cat 992 k wheel loader (prefix zmx) service repair manual (zmx000...fudjsjfekskkem
This document provides assembly instructions for a torque converter used in a 992K wheel loader. It lists over 60 steps and accompanying illustrations to assemble the various components of the torque converter in the proper order. Key components include seals, bearings, gears, plates, pistons, discs, sleeves, and housings. Special tools and lifting devices are required due to the large size and weights of components, which range from 25-680 kg. Proper temperatures and torques are specified for a safe and accurate reassembly of the torque converter.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, seals, gears, discs, plates, pistons, housings and other components. Proper cleaning, lubrication, and use of installation tools are emphasized.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a planetary transmission used in a 972H wheel loader. It describes how to assemble the input shaft, carrier assemblies, clutch components, output shaft, and other parts. Detailed steps and illustrations are provided to guide technicians through the assembly process. Cleanliness is emphasized and special tools are required to properly install some components like bearings. The assembly involves over 40 individual steps and requires lifting heavy parts into place.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections detailing the assembly of the transmission's planetary gear sets and clutches. The summary includes:
1) Cleaning and preparing transmission components before assembly.
2) Assembling the three planetary gear sets which include installing bearings, gears, shafts, seals and retaining rings.
3) Installing clutches which involve alternating friction discs and plates, installing seals, pistons and springs.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, gears, seals, springs, and other components. Proper cleaning and use of installation tools are noted.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, gears, seals, springs, and other components. Proper cleaning and use of installation tools are emphasized.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, gears, seals, springs, and other components. Proper cleaning and use of installation tools are emphasized.
This document provides assembly instructions for a 992K wheel loader torque converter. It lists over 60 steps and required tools to assemble the various components of the torque converter. Key parts that are assembled include the shaft assembly, carrier assembly, gears, housing assembly, impeller clutch, turbine assembly, clutch housing assembly, and pump adapters. Lifting devices and special tools are required due to the heavy weights of components like the housing assembly and impeller clutch.
This document provides assembly instructions for a torque converter in a 992K wheel loader. It lists over 40 steps and required tools to assemble internal components like seals, bearings, gears, and housings. Proper lifting equipment is needed due to component weights up to 590kg. Tolerances and torque specifications are provided.
This document provides assembly instructions for a 992K wheel loader torque converter. It lists over 60 steps and required tools to assemble the various components of the torque converter. Key parts that are assembled include the shaft assembly, carrier assembly, gears, housing assembly, impeller clutch, turbine assembly, clutch housing assembly, and pump adapters. Lifting devices and special tools are required due to the heavy weights of components like the housing assembly and impeller clutch.
Similar to Caterpillar Cat 924Gz Wheel Loader (Prefix WMB) Service Repair Manual (WMB00001 and up).pdf (15)
Caterpillar Cat CP-663E Vibratory Compactor (Prefix AEF) Service Repair Manua...ujkfdkkmsmd
This document provides disassembly and assembly instructions for a piston pump used in vibratory compactors. It describes 41 steps to fully disassemble the pump into individual components. This includes removing seals, springs, valves, pistons, plates, blocks, bearings and other parts. Similarly, it lists 41 steps for reassembling all the components in the reverse order. Cleanliness is emphasized throughout the process.
Caterpillar Cat CP-583E Vibratory Compactor (Prefix CNX) Service Repair Manua...ujkfdkkmsmd
This document provides instructions for removing and installing piston cooling jets, pistons, connecting rods, and related components on a Caterpillar 3056E engine. The removal process involves taking out the engine oil pan, removing valve assemblies from the piston cooling jets, and pushing pistons and connecting rods out of the cylinder block. The installation process requires cleaning components, lubricating them with oil, and reinserting pistons and connecting rods into the cylinder block before replacing other parts. Safety notices are provided to keep components clean and contain fluids.
Caterpillar Cat CP-573E Vibratory Compactor (Prefix CEB) Service Repair Manua...ujkfdkkmsmd
The document provides instructions for removing and installing the final drive planetary and piston motor components on a CS-573E and CP-573E vibratory compactor. It describes using various tools to disassemble components like the housing, hub, gears, seals and installing new components in the reverse order. Precise torques and clear illustrations are provided to correctly assemble the final drive planetary.
Caterpillar Cat CP-563D Vibratory Compactors (Prefix 2RZ) Service Repair Manu...ujkfdkkmsmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on CP-563D and CS-563D vibratory compactors powered by a 3116 engine. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure refers to ensuring parts are clean and checking guidelines for determining if valve seats can be reused.
Caterpillar Cat CP-533E Vibratory Compactor (Prefix ASL) Service Repair Manua...ujkfdkkmsmd
This document provides instructions for disassembling and assembling the piston pump used for drum propulsion on vibratory compactor models CS-533E and CP-533E. The disassembly procedure involves removing 28 components from the pump in 12 steps using various tools. Cleaning and inspecting parts is emphasized before reassembly in the reverse order over 28 steps.
Caterpillar Cat CP-533D Vibratory Compactor (Prefix AET) Service Repair Manua...ujkfdkkmsmd
This document provides instructions for removing and installing inlet and exhaust valve guides on a CS-533D and CP-533D vibratory compactor. It outlines the required tools and gives step-by-step instructions for removing the old guides and pressing new guides into the cylinder head assembly. Proper cleaning and lubrication of parts is emphasized to prevent premature wear. Reusability guidelines for different components are also referenced.
Caterpillar Cat CP-433E Vibratory Compactor (Prefix DAC) Service Repair Manua...ujkfdkkmsmd
The document provides instructions for assembling and disassembling various components of a vibratory compactor model CS-433E or CP-433E, including:
- Assembling the piston motor drum propel system in 24 steps requiring various tools.
- Installing the assembled piston motor drum propel system with 2 illustrations.
- Removing the final drive planetary from the drum propel in 7 steps requiring lifting tools and draining the oil first.
This document provides disassembly instructions for the final drive of a 5110B mining excavator. It lists the required tools and steps to disassemble the various components of the final drive. The major steps include removing the gears, carriers, housings and other components using specialized tools like pullers and presses. Cleanliness is emphasized to prevent contamination of hydraulic components during disassembly and reassembly.
Caterpillar Cat CB534B Roller Service Repair Manual.pdfujkfdkkmsmd
This document provides instructions for replacing the propel speed range switch on models CB534B and CB534C rollers. It describes removing the operator station panel assembly, propel speed range switch, and associated wires and lockwashers. It then describes installing the new propel speed range switch with wires and lockwashers and reinstalling the panel assembly.
Caterpillar Cat CB534C Roller Service Repair Manual.pdfujkfdkkmsmd
This document provides instructions for replacing the propel speed range switch on models CB534B and CB534C rollers. It describes removing the operator station panel assembly, propel speed range switch, and associated wires and lockwashers. It then describes installing the new propel speed range switch with wires and lockwashers and reinstalling the panel assembly.
This document provides disassembly instructions for the final drive of a 5110B mining excavator. It outlines 33 steps to fully disassemble the final drive, including removing gears, carriers, housings, seals, bearings, and other components. Special tools are required and cleanliness is important to prevent contamination of parts. The document emphasizes safety precautions due to heavy component weights and potential for flying debris or released spring forces during disassembly.
Caterpillar Cat 5080 FRONT SHOVEL (Prefix 8SL) Service Repair Manual (8SL0000...ujkfdkkmsmd
This document provides instructions for removing and installing fuel injection nozzles and adapters on a 5080 FRONT SHOVEL excavator with a 3406B engine. It describes using various tools to disconnect fuel lines, remove retainers and nozzles, and clean parts. Detailed steps are given for installing nozzles, adapters, seals and applying lubricants. Similar level of detail is provided for removing and installing the cylinder head assembly, spacer plate, and valves.
This document provides disassembly instructions for a 992K wheel loader torque converter. It lists over 50 individual steps to disassemble the various components of the torque converter housing assembly, including removing pumps, gears, seals, bearings, and other internal parts. Detailed illustrations accompany each step to show how to position the assembly, what tools are needed, and how to separate the individual components. The overall process involves disassembling the entire torque converter and transmission housing to access all internal parts.
This document provides instructions for servicing the power train components of a 992B wheel loader, including removing and installing axles, final drive carriers, ring gears, hubs, wheels, and wheel brakes. The document is divided into several sections covering different components, and each section provides detailed step-by-step instructions and diagrams for disassembly and assembly of the specified components. Safety precautions and notes are included throughout.
This document provides disassembly instructions for a 992K wheel loader torque converter. It describes removing 57 individual components through a step-by-step process involving specialized tools. Key parts that must be removed include the torque converter housing, pump adapter, idler gear, housing assembly, pump drive gear, turbine assembly, impeller clutch, and shaft assembly. Precise instructions are given for each removal to ensure safety and prevent damage to precision components.
This document provides instructions for servicing the power train components of a Caterpillar 992B wheel loader, including removing and installing axles, final drive carriers, ring gears, hubs, wheels, and wheel brakes. The steps describe using hoists and tools to remove heavy components and reassemble them in reverse order. Weights of removed parts are provided to aid technicians performing the work.
This document provides disassembly instructions for the transmission planetary system of a 992G wheel loader. It outlines 52 steps to fully disassemble the transmission, including removing components like the transmission case assembly, end plates, clutches, planetary carrier, and sun gear. Various tools are required to separate, remove, and disassemble the different transmission parts. Detailed illustrations accompany each step to show how to properly disassemble the transmission planetary.
This document provides disassembly instructions for the transmission planetary of a 992G wheel loader. It lists 57 steps to fully disassemble the transmission planetary, including removing components like the transmission case assembly, carrier assembly, clutch housings, and planetary gears. Detailed illustrations accompany each step to show how to remove seals, bolts, springs, and other parts. Special tools are required for tasks like separating transmission components and removing bearings.
This document provides instructions for removing and installing an electronic unit injector on a Caterpillar 3508 engine. It describes:
1. Removing the rocker shaft assembly, pushrods, clamps and bolts to remove the injector.
2. Cleaning the cylinder head bore before installing the new injector.
3. Installing the injector, connecting the harness, and reinstalling removed components.
This document provides instructions for removing and installing the cylinder head on a Caterpillar 3412E engine. It lists the required tools and gives step-by-step details of the removal and installation process. The removal process involves detaching hoses, bolts, and manifolds. Lifting devices are needed due to the heavy weight of parts. The installation process reverses the removal steps and provides tightening specifications for bolts. Precautions are given to keep parts clean and apply lubricants to seals.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 924G WHEEL LOADER WMB
Configuration: 924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Power
Train
Media Number -RENR6422-07 Publication Date -01/10/2017 Date Updated -09/10/2017
i06103589
Transmission and Torque Converter - Assemble
SMCS - 3001-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 180-3033 Repair Stand Set 1
C 138-7574 Link Bracket 2
D 4C-6136 Lifting Bracket 1
E 4C-6399 Compressor Assembly (Clutch Spring) 1
F FT-2343 Plexiglass Cover 1
H 4C-3652 Compressor Assembly (Clutch Spring) 1
J 4C-6402 Expander Tool Gp 1
K
4C-6137 Bearing Installer 1
4C-6142 Spacer 1
1P-0531 Handle 1
L 5P-3413 Pipe Sealant 1
M 9S-3263 Thread Lock Compound 1
N 1U-8846 Gasket Sealant 1
1/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. P 4C-6143 Clutch Piston Installer 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01005243
1. Install gear (149) and retaining ring (148) . Raise the temperature of bearing cone (147) .
Install bearing cone (147) .
Illustration 2 g01005241
2. Raise the temperature of bearing cone (146) . Install bearing cone (146) .
2/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01005239
3. Apply Tooling (L) to the seal bore.
4. Install lip seal (145) . Lubricate the sealing lip with the lubricant that is being used.
5. Lower the temperature of bearing cup (143) . Install bearing cup (143) .
6. Use bolts (142) in order to install shield assembly (144) . Tighten bolts (142) to a torque of
55 ± 10 N·m (40 ± 10 lb ft).
Illustration 4 g01005238
7. Install the output shaft and gear (141) .
3/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01005236
8. Install lip seal (140) . Lubricate the sealing lip with the lubricant that is being used.
9. Lower the temperature of bearing cup (139) . Install bearing cup (139) .
10. Install seal (138) .
11. Install shims (137) . Use the shims in order to get 0.06 mm (0.002 inch) to 0.13 mm (0.005
inch) end play on the output shaft.
Note: Lubricate the bore of the housing with the lubricant that is being used.
Illustration 6 g00655180
12. Use bolts (135) in order to install the cage. Tighten bolts (135) to a torque of 70 ± 10 N·m
(50 ± 10 lb ft).
4/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 7 g00890758
13. Install parking brake assembly (133) and lever (134) .
14. Use bolts (131) in order to install plate (132) . Tighten bolts (131) to a torque of 120 ± 20
N·m (90 ± 15 lb ft).
Illustration 8 g00890622
15. Install brake drum (130) and yoke (129) together. Install seal (128) .
5/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 9 g00685060
16. Install the bolt and washer (127) . Tighten bolt (127) to a torque of 120 ± 20 N·m (90 ± 15
lb ft).
Illustration 10 g00655120
17. Use washer (125) and bolt (124) in order to install yoke (126) . Tighten bolt (124) to a
torque of 120 ± 20 N·m (90 ± 15 lb ft).
Illustration 11 g00655110
18. Lower the temperature of bearing cups (123) . Install bearing cups (123) . Use Tooling (J) to
install bearing (122) .
6/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g00890621
19. Install gear (119) . Raise the temperature of bearing cone (118) . Install bearing cone (118) .
20. Install gear (120) . Raise the temperature of bearing cone (121) . Install bearing cone (121) .
21. Install seal (116) on carrier (117) and install carrier (117) .
Illustration 13 g00655016
22. Install the input shaft assembly (115) .
7/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 14 g00654969
23. Install seals (112) , (113) , and (114) .
Illustration 15 g00654966
Note: Lubricate the piston, and the bore with clean transmission oil.
24. Use Tooling (P) in order to install piston (111) .
Illustration 16 g00654842
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
8/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 25. Install spring (110) .
Illustration 17 g00654837
26. Install the retainer and seal assembly (109) .
Illustration 18 g00654833
27. Put the clutch pack in a suitable press. Use Tooling (H) in order to install retaining ring
(108) .
9/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 19 g00654824
28. Lower the temperature of bearing assembly (107) . Install bearing assembly (107) .
Illustration 20 g00654818
29. Install ring (106) .
Illustration 21 g00890619
10/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Note: Refer to Specifications, "Power Shift Transmission" for the specifications of the
clutch discs.
30. Install plates and discs (105) . Install retaining ring (103) . Install washers (104) and (102) .
Illustration 22 g00654724
31. Install hub assembly (101) .
Illustration 23 g00654719
32. Install gear (100) and retaining ring (99) . Install washer (98) .
11/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 24 g00656434
33. Install gear (95) and washer (96) . Raise the temperature of bearing (97) . Install bearing
(97) .
Note: This completes the assembly of the first gear clutch pack.
Note: Refer to Specifications, "Power Shift Transmission" for the procedure to measure
running clearance.
Illustration 25 g00654638
34. Install seals (94) and (93) .
12/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 26 g00890838
Note: Lubricate the piston, and the bore with clean transmission oil.
35. Use Tooling (P) in order to install piston (90) .
36. Install seals (92) on shaft (91) .
Illustration 27 g00654534
37. Install spring (89) and retainer (88) .
13/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 28 g00654525
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
38. Put the third gear clutch pack in a suitable press. Use Tooling (H) in order to install
retaining ring (87) .
Illustration 29 g00654519
Note: Refer to Specifications, "Power Shift Transmission" for the specifications of the
clutch discs.
39. Install plates and discs (86) . Install retaining ring (85) .
40. Install washer (84) .
14/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 30 g00654517
41. Use a suitable press in order to install bearing (83) . Install retaining ring (82) .
Illustration 31 g00654512
42. Install hub assembly (81) .
Illustration 32 g00654507
43. Install gear (80) and retaining ring (79) .
15/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 33 g00654497
44. Install washer (78) and retaining ring (77) .
Note: This completes the assembly of the third gear clutch pack.
Note: Refer to Specifications, SENR3504, "Power Shift Transmission" for the procedure to
measure running clearance .
Illustration 34 g00654494
45. Use Tooling (D) in order to install third gear clutch pack (76) . The weight of third gear
clutch pack (76) is approximately 50 kg (110 lb).
16/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 35 g00890612
Note: Use Steps 46 through 49 for the assembly of the clutch of the second gear clutch
pack. Use Tooling (E) in step 49 instead of Tooling (H) .
46. Install washers (75) and (74) . Install spacer (73) .
47. Install gear (72) , spacer (70) , and bearing cone (71) .
Illustration 36 g00654403
48. Install seals (69) and (68) .
17/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 37 g00890841
Illustration 38 g00654372
Note: Lubricate the piston and the bore with clean transmission oil.
49. Use Tooling (P) in order to install piston (65) . Install seals (66) on shaft (67) .
Illustration 39 g00654364
50. Install spring (64) and retainer (63) .
18/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 40 g00654360
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
51. Put the reverse clutch pack in a suitable press. Use Tooling (H) in order to install retaining
ring (62) .
Illustration 41 g00890611
52. Use a suitable press in order to install bearing (61) . Install retaining ring (60) .
19/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 42 g00890610
Note: Refer to Specifications, "Power Shift Transmission" for the specifications of the
clutch discs.
53. Install plates and discs (59) . Install retaining ring (57) .
54. Install washer (58) .
Illustration 43 g00654347
55. Install hub assembly (56) .
20/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 44 g00654328
56. Install gear (55) and retaining ring (54) .
Illustration 45 g00654339
57. Install washer (53) and retaining ring (52) .
Note: This completes the assembly of the reverse second gear clutch pack.
Note: Refer to Specifications, "Power Shift Transmission" for the procedure to measure
running clearance.
21/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 46 g00654301
58. Use Tooling (D) in order to install reverse second gear clutch pack (51) . The weight of
reverse second gear clutch pack (51) is approximately 32 kg (70 lb).
Illustration 47 g00654292
59. Install seals (49) and (50) .
Illustration 48 g00654280
22/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Note: Lubricate the piston, and the bore with clean transmission oil.
60. Use Tooling (P) in order to install piston (47) .
61. Install spring (46) and retainer (45) .
Illustration 49 g00654276
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
62. Put the forward high clutch pack in a suitable press. Use Tooling (H) in order to install
retaining ring (44) .
23/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 50 g00654274
Note: Refer to Specifications, "Power Shift Transmission" for specifications of the clutch
discs.
63. Install plates and discs (43) . Install retaining ring (42) . Install washer (41) .
Illustration 51 g00654263
64. Use a suitable press in order to install bearing (40) . Install retaining ring (39) .
Illustration 52 g00654261
65. Install hub (38) .
24/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 53 g00654253
66. Raise the temperature of gear (37) . Install gear (37) . Install retaining ring (36) .
Illustration 54 g00654078
67. Install washer (35) and retaining ring (34) .
Note: This completes the assembly of the forward high gear clutch pack.
Note: Refer to Specifications, "Power Shift Transmission" for the procedure to measure
running clearance.
25/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 55 g00654063
68. Install O-ring seals (33) .
Illustration 56 g00890845
Note: Lubricate the piston, and the bore with clean transmission oil.
69. Use Tooling (P) in order to install piston (31) . Install seals (32) on shaft (30) .
Illustration 57 g00654029
26/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 70. Install spring (29) and retainer (28) .
Illustration 58 g00654018
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
71. Put the forward low clutch pack in a suitable press. Use Tooling (H) in order to compress
the spring. Install retaining ring (27) .
Illustration 59 g00890608
72. Use a suitable press in order to install bearing (25) . Install retaining ring (26) in hub (22) .
27/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 60 g00653959
73. Install washer (24) .
Illustration 61 g00890607
Note: Refer to Specifications, "Power Shift Transmission" for specifications of clutch discs.
74. Install plates and discs (23) . Install hub (21) . Install retaining ring (22) .
28/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
31. Illustration 62 g00653932
75. Raise the temperature of gear (20) . Install gear (20) . Install retaining ring (19) .
Illustration 63 g00653893
76. Install washer (18) and retaining ring (17) .
Note: This completes the assembly of the forward low gear clutch pack.
Note: Refer to Specifications, "Power Shift Transmission" for the procedure to measure
running clearance.
Illustration 64 g00653858
77. Use Tooling (D) in order to install the forward low and the forward high clutch pack (15) .
The weight of forward high clutch pack (15) is approximately 27 kg (60 lb).
Note: Use Tooling (J) in order to install plugs (16) .
29/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. Illustration 65 g00653848
78. Lower the temperature of bearing cups (14) . Use Tooling (K) in order to install bearing
cups (14) .
Illustration 66 g00653825
79. Use bolts (12) in order to install gear (13) . Tighten bolts (12) to a torque of 12 ± 3 N·m (10
± 2 lb ft).
Illustration 67 g00653808
30/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. 80. Install gear assembly (10) .
81. Install O-ring seals (11) .
Illustration 68 g00653806
82. Install bolts (9) . Tighten bolts (9) to a torque of 55 ± 10 N·m (40 ± 10 lb ft).
Illustration 69 g00653801
83. ApplyTooling (L) to the seal bore.
84. Install lip seal (7) . Lubricate the sealing lip with the lubricant that is being used.
85. Install seal (8) .
31/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...