Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 924G WHEEL LOADER AAN
Configuration: 924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056 Engine
Disassembly and Assembly
924G and 924GZ Wheel Loaders Power Train
Media Number -RENR3506-05 Publication Date -01/05/2004 Date Updated -09/10/2017
i02055589
Power Shift Transmission - Assemble
SMCS - 3030-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 1U-9759 Jack Stand 1
C 6V-2156 Link Bracket 2
D 4C-6136 Lifting Bracket 1
E 4C-6399 Spring Compressor 1
F FT-2343 Plexiglass Cover 1
G 4C-6143 Clutch Piston Installer 1
H 4C-3652 Spring Compressor 1
J
4C-6137 Bearing Installer 1
4C-6142 Spacer 1
1P-531 Handle 1
K 4C-6402 Plug Installer 1
L 5P-3413 Pipe Sealant 1
M 9S-3263 Thread Lock Compound 1
N 1U-8846 Gasket Sealant 1
1/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056 E...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g00655451
1. Install gear (152) and ring (151). Heat bearing (150) to a temperature of 135 °C (275 °F).
Install bearing (150).
Illustration 2 g00655464
2. Heat bearing (149) to a temperature of 135 °C (275 °F). Install bearing (149).
2/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056 E...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00890761
3. ApplyTooling (L) to the seal bore.
4. Install lip seal (148). Lubricate the sealing lip with the lubricant that is being used.
5. Lower the temperature of bearing cup (146). Install bearing cup (146).
6. Use bolts (145) in order to install shield assembly (147). The torque for bolts (145) is
55 ± 10 N·m (40 ± 10 lb ft).
Illustration 4 g00655439
7. Install the output shaft and gear (144).
Illustration 5 g00890760
8. Use nuts (142) in order to install cover (143). The torque for nuts (142) is 9 ± 1 N·m
(6 ± 1 lb ft).
3/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056 E...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g00890759
9. Install lip type seal (141). Lubricate the sealing lip with the lubricant that is being used.
10. Lower the temperature of bearing cup (140). Install bearing cup (140).
11. Install seal (139).
Illustration 7 g00655206
12. Install shims (138). Use the shims in order to get 0.06 mm (0.002 inch) to 0.13 mm
(0.005 inch) end play on the output shaft.
Note: Lubricate the bore of the housing with the lubricant that is being used.
4/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056 E...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g00655180
13. Use bolts (135) in order to install the cage. The torque for bolts (135) is 70 ± 10 N·m
(50 ± 10 lb ft).
Illustration 9 g00890758
14. Install parking brake assembly (133) and lever (134).
15. Use bolts (131) in order to install plate (132). The torque for bolts (131) is 120 ± 20 N·m
(90 ± 15 lb ft).
Illustration 10 g00890622
16. Install brake drum (130) and yoke (129) together. Install seal (128).
5/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056 E...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00685060
17. Install the bolt and washer (127). The torque for bolt (127) is 120 ± 20 N·m (90 ± 15 lb ft).
Illustration 12 g00655120
18. Use washer (125), and bolt (124) in order to install yoke (126) . The torque for bolt (124) is
120 ± 20 N·m (90 ± 15 lb ft).
Illustration 13 g00655110
19. Lower the temperature of bearing cups (123). Install bearing cups (123). Use Tooling (J) to
install bearing (122).
6/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056 E...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00890621
20. Install gear (119). Heat bearing (118) to a temperature of 135 °C (275 °F). Install bearing
(118).
21. Install gear (120). Heat bearing (121) to a temperature of 135 °C (275 °F). Install bearing
(121).
22. Install seal (116) on carrier (117), and install carrier (117).
Illustration 15 g00655016
23. Install the input shaft assembly (115).
Illustration 16 g00654969
7/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056 E...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 24. Install seals (112), (113), and (114).
Illustration 17 g00654966
Note: Lubricate the piston, and the bore with clean transmission oil.
25. Use Tooling (G) in order to install piston (111).
Illustration 18 g00654842
26. Install spring (110).
Illustration 19 g00654837
8/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056 E...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 27. Install the retainer and seal assembly (109).
Illustration 20 g00654833
28. Put the clutch pack in a suitable press. Use Tooling (H) in order to install ring (108).
Illustration 21 g00654824
29. Lower the temperature of bearing assembly (107). Install bearing assembly (107).
Illustration 22 g00654818
30. Install ring (106).
9/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056 E...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 23 g00890619
Note: Refer to Specifications, SENR3504, "Power Shift Transmission" for the
specifications of the clutch discs.
31. Install plates and discs (105). Install ring (103). Install washers (104) and (102).
Illustration 24 g00654724
32. Install hub assembly (101).
Illustration 25 g00654719
33. Install gear (100) and ring (99). Install washer (98).
10/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 26 g00656434
34. Install gear (95) and washer (96). Heat bearing (97) to a temperature of 135 °C (275 °F).
Install bearing (97).
Note: This completes the assembly of the first gear clutch pack.
Note: Refer to Specifications, SENR3504, "Power Shift Transmission" for the procedure to
measure running clearance.
Illustration 27 g00654638
35. Install seals (94) and (93).
11/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 28 g00890838
Note: Lubricate the piston, and the bore with clean transmission oil.
36. Use Tooling (G) in order to install piston (90).
37. Install seals (92) on shaft (91).
Illustration 29 g00654534
38. Install spring (89), and retainer (88).
Illustration 30 g00654525
39. Put the third gear clutch pack in a suitable press. Use Tooling (H) in order to install ring
(87).
12/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 31 g00654519
Note: Refer to Specifications, SENR3504, "Power Shift Transmission" for the
specifications of the clutch discs.
40. Install plates and discs (86). Install ring (85).
41. Install washer (84).
Illustration 32 g00654517
42. Use a suitable press in order to install bearing (83). Install ring (82).
Illustration 33 g00654512
13/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 43. Install hub assembly (81).
Illustration 34 g00654507
44. Install gear (80) and ring (79).
Illustration 35 g00654497
45. Install washer (78) and ring (77).
Note: This completes the assembly of the third gear clutch pack.
Note: Refer to Specifications, SENR3504, "Power Shift Transmission" for the procedure to
measure running clearance .
14/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 36 g00654494
46. Use Tooling (D) in order to install third gear clutch pack (76). The weight of the clutch pack
is approximately 50 kg (110 lb).
Illustration 37 g00890612
Note: Use steps 47 through 50 for the assembly of the clutch of the second gear clutch pack.
Use Tooling (E) in step 50 instead of Tooling (H).
47. Install washers (75) and (74). Install spacer (73).
48. Install gear (72), spacer (70), and bearing (71).
Illustration 38 g00654403
49. Install seals (69) and (68).
15/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 39 g00890841
Illustration 40 g00654372
Note: Lubricate the piston and the bore with clean transmission oil.
50. Use Tooling (G) in order to install piston (65). Install seals (66) on shaft (67).
Illustration 41 g00654364
51. Install spring (64) and retainer (63).
16/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 42 g00654360
52. Put the reverse clutch pack in a suitable press. Use Tooling (H) in order to install ring (62).
Illustration 43 g00890611
53. Use a suitable press in order to install bearing (61). Install ring (60).
Illustration 44 g00890610
Note: Refer to Specifications, SENR3504, "Power Shift Transmission" for the
specifications of the clutch discs.
54. Install plates and discs (59). Install ring (57).
17/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 55. Install washer (58).
Illustration 45 g00654347
56. Install hub assembly (56).
Illustration 46 g00654328
57. Install gear (55) and ring (54).
Illustration 47 g00654339
58. Install washer (53) and ring (52).
18/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Note: This completes the assembly of the reverse second gear clutch pack.
Note: Refer to Specifications, SENR3504, "Power Shift Transmission" for the procedure to
measure running clearance.
Illustration 48 g00654301
59. Use Tooling (D) in order to install reverse second gear clutch pack (51). The weight of the
clutch pack is approximately 32 kg (70 lb).
Illustration 49 g00654292
60. Install seals (49) and (50).
19/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 50 g00654280
Note: Lubricate the piston, and the bore with clean transmission oil.
61. Use Tooling (G) in order to install piston (47).
62. Install spring (46), and retainer (45).
Illustration 51 g00654276
63. Put the forward high clutch pack in a suitable press. Use Tooling (H) in order to install ring
(44).
Illustration 52 g00654274
Note: Refer to Specifications, SENR3504, "Power Shift Transmission" for specifications of
the clutch discs.
64. Install plates and discs (43). Install ring (42). Install washer (41).
20/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 53 g00654263
65. Use a suitable press in order to install bearing (40). Install ring (39).
Illustration 54 g00654261
66. Install hub (38).
Illustration 55 g00654253
67. Heat gear (37) to a temperature of 135 °C (275 °F). Install gear (37). Install ring (36).
21/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 56 g00654078
68. Install washer (35) and ring (34).
Note: This completes the assembly of the forward high gear clutch pack.
Note: Refer to Specifications, SENR3504, "Power Shift Transmission" for the procedure to
measure running clearance.
Illustration 57 g00654063
69. Install O-ring seals (33).
Illustration 58 g00890845
22/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Note: Lubricate the piston, and the bore with clean transmission oil.
70. Use Tooling (G) in order to install piston (31). Install seals (32) on shaft (30).
Illustration 59 g00654029
71. Install spring (29) and retainer (28).
Illustration 60 g00654018
72. Put the forward low clutch pack in a press. Use Tooling (H) in order to compress the spring.
Install ring (27).
Illustration 61 g00890608
23/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 73. Use a suitable press in order to install bearing (25). Install ring (26) in hub (22).
Illustration 62 g00653959
74. Install washer (24).
Illustration 63 g00890607
Note: Refer to Specifications, SENR3504, "Power Shift Transmission" for specifications of
clutch discs.
75. Install plates and discs (23). Install hub (21). Install ring (22).
Illustration 64 g00653932
24/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 76. Heat gear (20) to a temperature of 135 °C (275 °F). Install gear (20). Install ring (19).
Illustration 65 g00653893
77. Install washer (18) and ring (17).
Note: This completes the assembly of the forward low gear clutch pack.
Note: Refer to Specifications, SENR3504, "Power Shift Transmission" for the procedure to
measure running clearance.
Illustration 66 g00653858
78. Use Tooling (D) in order to install the forward low and the forward high clutch pack (15).
The weight of the clutch pack is approximately 27 kg (60 lb).
Note: Use Tooling (K) in order to install plugs (16).
25/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 67 g00653848
79. Lower the temperature of bearings and race (14). Use Tooling (J) in order to install bearings
and race (14).
Illustration 68 g00653825
80. Use bolts (12) in order to install gear (13). The torque for bolts (12) is 12 ± 3 N·m
(10 ± 2 lb ft).
Illustration 69 g00653808
81. Install gear assembly (10).
26/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 82. Install O-ring seals (11).
Illustration 70 g00653806
83. Install bolts (9). The torque for bolts (9) is 55 ± 10 N·m (40 ± 10 lb ft).
Illustration 71 g00653801
84. Apply Tooling (L) to the seal bore.
85. Install lip type seal (7). Lubricate the sealing lip with the lubricant that is being used.
86. Install seal (8).
27/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 72 g00653775
Note: Lubricate the bore with the lubricant that is being used.
87. Use bolts (5) in order to install plate (6). The torque for bolts (5) is 55 ± 10 N·m
(40 ± 10 lb ft).
Illustration 73 g00671890
Note: Apply Tooling (M) to the threads of bolts (3).
88. Use bolts (3) in order to install flex plate (4) on torque converter (1). The torque for bolts
(151) is 60 ± 7 N·m (45 ± 5 lb ft).
Illustration 74 g00657224
89. Clean both mating surfaces of the transmission housing. Apply a continuous bead of
Tooling (N) to the mating surface of the transmission housing.
28/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 75 g00653680
90. Use Tooling (C) and a suitable lifting device in order to install the top transmission case.
Install bolts (2). The torque for bolts (2) is 55 ± 10 N·m (40 ± 10 lb ft). The weight of the
top transmission case is approximately 163 kg (360 lb).
Note: Install the selector and pressure control valve. Remove Tooling (F). Refer to
Disassembly and Assembly, "Selector And Pressure Control Valve (Transmission) -
Remove And Install".
91. Install torque converter (1).
92. Remove the transmission from Tooling (A) and (B). The weight of the transmission is
approximately 500 kg (1100 lb).
End By:
a. Connect the engine, and the transmission. Refer to Disassembly and Assembly, RENR3503,
"Engine to Torque Converter and Transmission - Connect".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jan 25 22:44:03 UTC+0800 2021
29/29
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
32. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 924G WHEEL LOADER AAN
Configuration: 924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056 Engine
Disassembly and Assembly
924G and 924GZ Wheel Loaders Power Train
Media Number -RENR3506-05 Publication Date -01/05/2004 Date Updated -09/10/2017
i01740177
Flow Control Valve - Remove and Install
SMCS - 5137-010-T3
Removal Procedure
Start By:
a. Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame
Lock - Separate and Connect".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1853 Retaining Pliers 1
Hot oil and hot components can cause personal injury. Do not allow hot
oil or hot components to contact skin.
At operating temperature, the engine coolant is hot and under pressure.
Steam can cause personal injury.
Check the coolant level only after the engine has been stopped and the
cooling system pressure cap is cool enough to touch with your bare
hand.
Remove the cooling system pressure cap slowly to relieve pressure.
1/8
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056 E...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. Cooling system conditioner contains alkali. Avoid contact with the skin
and eyes to prevent personal injury.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the transmission oil.
Illustration 1 g00664008
2. Remove hose assembly (1).
2/8
924G and 924Gz Wheel Loader AAN00001-UP (MACHINE) POWERED BY 3056 E...
2021/1/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...