This document provides instructions for assembling the transmission and torque converter of a 924H wheel loader. It lists required tools and gives step-by-step instructions with illustrations. Some key steps include installing bearings and seals, assembling various clutch packs using specialized tools, and ensuring proper end play and lubrication during assembly. Cleanliness and heating/cooling parts as needed during assembly is emphasized to avoid damage.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
1. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 924H WHEEL LOADER KLN
Configuration: 924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
924H, 924HZ, 928HZ and 930H Wheel Loaders Power Train
Media Number -KENR7606-09 Publication Date -01/03/2015 Date Updated -09/10/2017
i07377005
Transmission and Torque Converter - Assemble
SMCS - 3001-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-9200 Lever Puller Hoist 1
138-7575 Link Bracket 3
B
8T-0372
Bolt
M12 - 1.75 by 90mm
3
180-3033 Jack Stand Gp 2
180-3032 Jack Stand Gp 1
189-0410 Shackle As 2
D
1U-9200 Lever Puller Hoist 1
138-7575 Link Bracket 4
189-0409 Shackle As 1
F 136-1452 Retaining Ring Pliers As 1
H 1P-1863 Retaining Ring Pliers 1
J 4C-6136 Lifting Bracket 1
K 1P-1861 Retaining Ring Pliers 1
L 1P-0510 Driver Gp 1
1/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2. M 4C-3652 Compressor Assembly 1
N 1P-1857 Retaining Ring Pliers 1
R 4C-6399 Compressor Assembly 1
S 9S-3263 Thread Lock Compound -
T 1U-8846 Gasket Sealant -
U 4C-6402 Expander Tool Gp 1
V 8S-2328 Dial Indicator Gp 1
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning
fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be
deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. Dirt and other contaminants can damage the precision
component. Perform assembly procedures on a clean work surface. Keep components covered and
protected at all times.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
2/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01399408
1. Install gear (148) and retaining ring (147). Raise the temperature of bearing cone (146) to
install bearing cone (146).
Illustration 2 g01399402
2. Raise the temperature of bearing cone (145) to install bearing cone (145).
Illustration 3 g01399398
3. Lower the temperature of bearing cup (143) and install bearing cup (143). Install lip seal
(144).
Note: Lubricate the sealing lip with the lubricant that is being sealed.
4. Install shield assembly (142) and bolts (141). Tighten bolts (141) to a torque of 55 ± 10 N·m
(41 ± 7 lb ft).
3/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g01399397
5. Install the output shaft and gear (140).
Illustration 5 g01399379
6. Install lip seal (137). Lower the temperature of bearing cup (136) and install bearing cup
(143). Install seal (135).
Illustration 6 g06299489
7. Install shims (134), cage (133), and bolts (132).
4/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 8. Use shims as required to achieve 0.06 mm (0.002 inch) to 0.13 mm (0.005 inch) of end play
on the output shaft.
9. Tighten bolts (132) to a torque of 70 ± 10 N·m (52 ± 7 lb ft).
Illustration 7 g01399325
10. Install lever (131) and parking brake assembly (130).
11. Install plate (129). Install bolts (128).
Illustration 8 g01399321
12. Install brake drum (127) and yoke (126) together. Install seal (125).
5/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g01399193
13. Install washer (124) and bolt (123). Tighten bolt (123) to a torque of 120 ± 20 N·m
(89 ± 15 lb ft).
Illustration 10 g01399185
14. Install yoke (122), washer (121), and bolt (120). Tighten bolt (120) to a torque of
120 ± 20 N·m (89 ± 15 lb ft).
Illustration 11 g01399032
15. Lower the temperature of bearing cup (117) and install bearing cup (117). Install bearings
(118) and (119).
6/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 12 g01399007
16. Install gear (114). Raise the temperature of bearing cone (113) and carrier (111). Install
bearing cone (113) and carrier (111). Install ring seal (112) onto carrier (111).
17. Raise the temperature of bearing cone (116). Install gear (115) and bearing cone (116).
Illustration 13 g01398975
18. Install input shaft assembly (110).
Illustration 14 g01400893
19. Install seals (109) onto the piston.
7/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g01401266
Illustration 16 g01398781
Note: Lubricate the seals and the bore with the lubricant that is being sealed.
20. Position first gear and third gear clutch group (81), as shown. Install piston (108) and spring
(107).
21. Install seal assembly (105) and ring (106).
Illustration 17 g01398814
8/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
22. Position Tooling (R) onto seal assembly (105). Use Tooling (R) and a suitable press to
compress the clutch spring. Install retaining ring (104). Slowly release the spring tension.
Illustration 18 g01398776
23. Install retaining ring (102). Install clutch plates and discs (103).
24. Install plate (101) and retaining ring (100).
Illustration 19 g01398774
25. Install washer (99) and thrust disc (98).
9/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 20 g01398773
26. Lower the temperature of bearing (97) to install bearing (97) into hub (96). Install hub (96)
onto gear (94).
27. Use Tooling (H) to install retaining ring (95).
Illustration 21 g01398567
28. Install gear (94) and thrust disc (93).
Illustration 22 g01398565
29. Install gear (92) and spacer (91).
10/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 23 g01401044
30. Raise the temperature of bearing (90) to install bearing (90).
31. Refer to Step 58 through 65 for the assembly of the clutch pack.
Illustration 24 g01398664
32. Install thrust disc (89).
11/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 25 g01398657
33. Lower the temperature of bearing (88) to install bearing (88) into hub (85). Use Tooling (K)
to Install retaining ring (87).
Illustration 26 g01398645
34. Use Tooling (L) to install hub (85) into gear (84). Use Tooling (H) to install retaining ring
(86).
Illustration 27 g01398561
35. Install gear (84), thrust disc (83), and retaining ring (82).
12/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 28 g01398560
36. Attach Tooling (J) and a suitable lifting device to first gear and third gear clutch group (81).
The weight of clutch group (81) is approximately 45 kg (100 lb). Install clutch group (81).
Illustration 29 g01401308
37. Position the reverse and second clutch group (60), as shown.
38. Refer to Step 58 through 65 for the assembly of the clutch pack.
39. Install thrust disc (80).
Illustration 30 g01398456
40. Lower the temperature of bearing (79) to install bearing (79) into hub (76). Use Tooling (K)
to Install retaining ring (78).
13/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 31 g01398437
41. Use Tooling (L) to install hub (76) into gear (75). Use Tooling (H) to install retaining ring
(77).
Illustration 32 g01398280
42. Install gear (75).
14/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 33 g01398180
43. Install thrust disc (74), thrust disc (73), spacer (72), gear (71), spacer (70), and bearing (69).
44. Raise the temperature of bearing (69) to install bearing cone (69).
15/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 34 g01401335
45. Reposition the reverse and second clutch group (60), as shown.
46. Refer to Step 58 through 65 for the assembly of the clutch pack.
47. Install thrust disc (68).
Illustration 35 g01398270
48. Lower the temperature of bearing (67) to install bearing (67) into hub (64). Use Tooling (K)
to install retaining ring (66).
Illustration 36 g01398268
49. Use Tooling (L) to install hub (64) into gear (63). Use Tooling (H) to install retaining ring
(63).
16/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 37 g01397987
50. Install gear (63), thrust disc (62), and retaining ring (61).
Illustration 38 g01397984
51. Attach Tooling (J) and a suitable lifting device to the reverse and second clutch group (60).
The weight of clutch group (60) is approximately 32 kg (70 lb). Install clutch group (60).
Illustration 39 g01397953
52. Position the forward low and the forward high clutch group (26), as shown.
53. Refer to Step 58 through 65 for the assembly of the clutch pack.
17/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 54. Install thrust disc (59).
Illustration 40 g01397964
Illustration 41 g01401685
Dimension (X) is 5.25 ± 0.25 mm (0.207 ± 0.010 inch).
55. Install bearing (58) into the hub at the depth of 5.25 ± 0.25 mm (0.207 ± 0.010 inch).
56. Use Tooling (K) to remove retaining ring (57) from hub (56).
18/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 42 g01397884
57. Install hub (56), thrust disc (55), and retaining ring (54).
Illustration 43 g01397564
19/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
58. Reposition the clutch group, as shown. If equipped, install ball (51), spring (50), retainer
(49), seal (48), and retaining ring (47) into body (52).
59. Lubricate the bore and seal (48) with the lubricant that is being sealed and install valve
assembly (53).
60. Install rings (46).
Illustration 44 g01397562
61. Install seals (45) onto piston (44).
Note: Lubricate the seals with the lubricant that is being sealed.
20/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 45 g01397502
62. Install piston (44).
63. Install spring (43) and retainer (42).
Illustration 46 g01397484
21/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
64. Install Tooling (M) onto retainer (42). Use Tooling (M) and a suitable press to compress the
clutch spring. Install retaining ring (41). Slowly release the spring tension.
Illustration 47 g01397401
65. Install discs (39) and plates (40). Install plate (38) and retaining ring (37).
22/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 48 g01396540
66. Install thrust disc (36).
Illustration 49 g01396539
67. Lower the temperature of bearing (35) to install bearing (35) into hub (32). Use Tooling (K)
to install retaining ring (34).
23/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 50 g01396271
68. Use Tooling (L) to install hub (32) into gear assembly (31). Use Tooling (H) to install
retaining ring (33).
Illustration 51 g01397412
69. Install gear assembly (31).
Illustration 52 g01397406
70. Install thrust disc (30) and retaining ring (29).
Note: If the plugs in the shaft were removed during disassembly use Tooling (U) to install
the plugs.
24/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 53 g01396258
71. Use Tooling (J) and a suitable lifting device to remove the forward low and the forward
high clutch group (26). The weight of the clutch group is approximately 27 kg (60 lb).
Position shaft assembly (27) out of the way and install the forward low and the forward high
clutch group (26).
72. Install sensors (28). Tighten sensors (28) to a torque of 37 ± 7 N·m (27 ± 5 lb ft).
Illustration 54 g01396015
73. Lower the temperature of bearing cup (24) and install bearing cup (24). Lower the
temperature of bearings (25) and install bearings (25).
25/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 55 g01396014
74. Install bearing (22) into bearing support (21). Install bearing support (21) into the bearing.
Use Tooling (H) to install retaining ring (23).
Illustration 56 g01401529
Illustration 57 g01396199
26/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 75. Use a suitable press to install bearing assembly (20) into gear (18). Use Tooling (F) to
install retaining ring (19).
76. Install gear (18) onto the stator support. Apply Tooling (S) to the threads of bolts (17).
Install bolts (17).
77. Tighten bolts (17) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
Illustration 58 g01393451
Illustration 59 g01395994
78. Install gear assembly (16) and bolts (15). Tighten bolts (15) to a torque of 55 ± 10 N·m
(41 ± 7 lb ft).
27/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
29. Illustration 60 g01393407
79. Apply a continuous bead of Tooling (T) to the mating surface of the transmission housings.
80. Attach Tooling (D) and a suitable lifting device to housing assembly (13). The weight of
housing assembly (13) is approximately 141 kg (310 lb). Position housing assembly (13)
and install bolts (14). Tighten bolts (14) to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
Illustration 61 g03336943
81. Use Tooling (V) to check the end play. Make sure that the shafts are free. After checking
clearence, rotate shaft 7 times to ensure tapered roller bearing is seated. Use shims to obtain
0.05 mm (0.002 inch) to 0.15 mm (0.006 inch) of end play.
28/32
924H Wheel Loader KLN00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...