Caterpillar Cat 627G Wheel Tractor (Prefix AXF) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
627G Wheel Scraper

Shutdown SIS
Previous Screen
Product: WHEEL TRACTOR
Model: 627G WHEEL TRACTOR AXF
Configuration: 627G Wheel Tractor AXF00001-UP (MACHINE) POWERED BY 3406E Engine
Disassembly and Assembly
627G Wheel Tractor
Power Train
Media Number -RENR5736-02 Publication Date -01/08/2007 Date Updated -14/08/2007
i02301155
Transfer Gears - Disassemble
SMCS - 3159-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B
8B-7548 Push-Puller Tool Gp 1
8B-7551 Bearing Puller Gp 1
1P-0498 Drive Plate 1
C
5P-4170 Step Plate 1
1P-2321 Combination Puller 1
D
8B-7554 Bearing Cup Puller Gp 1
5P-4170 Step Plate 1
1P-0518 Drive Plate 1
E
8B-7560 Step Plate 1
5F-7345 Screw 1
8B-7554 Bearing Cup Puller Gp 1
F -
Bolts
3/8" - 16 NC by 3 inch
3
1/8(W)
w
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

Start By:
a. Remove the transfer gear case. Refer to Disassembly and Assembly, "Transfer Gears -
Remove".
b. Remove the transmission oil filter base. Refer to Disassembly and Assembly, "Transmission
Oil Filter Base - Remove and Install".
c. Remove the transmission scavenge pump. Refer to Disassembly and Assembly,
"Transmission Scavenge Pump - Remove".
d. Remove the transmission oil pump. Refer to Disassembly and Assembly, "Transmission Oil
Pump - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
1. Put identification marks on components for installation purposes.
2/8(W)
w
2021/5/15

Illustration 1 g01048669
2. Remove the bolts that secure bearing cage (1) to the transfer gear case. Use Tooling (F) in
order to separate bearing cage (1) from the transfer gear case.
3. Remove bearing cage (1), shims (2), and pump drive gear (3) from the transfer gear case.
5. Remove bearing cage (4), shims (5), and gear (6) from the transfer gear case.
3/8(W)
w
2021/5/15

6. Remove bearing cups (7) and (8) from the transfer gear case. Attach Tooling (A) and a
suitable lifting device onto the transfer gear case. The weight of the transfer gear case is
approximately 340 kg (750 lb). Turn over the transfer gear case. Remove Tooling (A).
8. Remove bearing cage (9), shims (10), and gear (11) from the transfer gear case.
9. Remove bearing cup (12) from the transfer gear case. Attach Tooling (A) and a suitable
lifting device onto the transfer gear case. Turn over the transfer gear case.
4/8(W)
w
2021/5/15

10. Remove bolts (13) that secure bearing cage (14) to the transfer gear case. If necessary, rotate
the gear until the three threaded holes are visible in bearing cage (14). Install Tooling (F)
through gear (15) and into bearing cage (14). Tighten Tooling (F) evenly until bearing cage
(14) and gear (15) separate from the transfer gear case. Remove bearing cage (14) and gear
(15) as a unit from the transfer gear case.
11. Remove retaining ring (16) from gear (15). Remove bearing (17) and bearing cage (14)
from gear (15).
5/8(W)
w
2021/5/15

12. Remove bearing (17) from bearing cage (14).
13. Remove bolts (19) and separate gear (20) from gear (11). Use Tooling (B) to remove
bearing cone (18) from gear (11). Repeat the procedure for the bearing cone on the opposite
side of the gear.
14. Use Tooling (C) to remove bearing cone (21) from gear (6). Repeat the procedure for the
bearing cone on the opposite side of gear (6).
6/8(W)
w
2021/5/15

15. Use Tooling (C) to remove bearing cone (22) from gear (3). Repeat the procedure for the
bearing cone on the opposite side of gear (3).
16. Use Tooling (D) to remove bearing cup (23) from bearing cage (4). Remove O-ring seal
(24) from bearing cage (4).
17. Remove bearing cup (25) from bearing cage (9).
7/8(W)
w
2021/5/15

18. Use Tooling (E) to remove bearing cup (26) from bearing cage (1). Remove O-ring seal (27)
from bearing cage (1).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 15 13:01:48 UTC+0800 2021
8/8(W)
w
2021/5/15

Shutdown SIS
Previous Screen
627G Wheel Tractor
Power Train
i07232119
Transfer Gears - Assemble
SMCS - 3159-016
Assembly Procedure
Table 1
Required Tools
G 1P-0510 Driver Group 1
H 8T-5096 Dial Indicator 1
NOTICE
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
1/9(W)
w
2021/5/15

1. Clean all parts and inspect all parts. If any parts are worn or damaged, use new parts for
replacement.
2. Lubricate O-ring seals with the lubricant that is being sealed.
3. Install bearing (17) into bearing cage (14).
4. Use Tooling (G) to install bearing (17) and bearing cage (14) to gear (15). Install bearing
(17) and bearing cage (14) until the retaining ring groove is visible. Install retaining ring
(16) to gear (15).
2/9(W)
w
2021/5/15

5. Position gear (15) and bearing cage (14) in the transfer gear case. Install bolts (13) that
secure bearing cage (14) to the transfer gear case. Tighten bolts (13) to a torque of
55 ± 10 N·m (41 ± 7 lb ft).
6. Install O-ring seal (27) onto bearing cage (1). Lower the temperature of bearing cup (26).
Install bearing cup (26) to bearing cage (1). Check that bearing cup (26) is seated in the bore
of bearing cage (1).
7. Lower the temperature of bearing cup (25). Install bearing cup (25) to bearing cage (9).
Check that bearing cup (25) is seated in the bore of bearing cage (9).
3/9(W)
w
2021/5/15

8. Install O-ring seal (24) to bearing cage (4). Lower the temperature of bearing cup (23).
Install bearing cup (23) to bearing cage (4). Check that bearing cup (23) is seated in the bore
of bearing cage (4).
9. Raise the temperature of bearing cone (22). Install bearing cone (22) on gear (3). Repeat the
procedure for the bearing cone on the opposite side of gear (3).
4/9(W)
w
2021/5/15

10. Raise the temperature of bearing cone (21). Install bearing cone (21) on gear (6). Repeat the
procedure for the bearing cone on the opposite side of gear (6).
11. Raise the temperature of bearing cone (18). Install bearing cone (18) on gear (11). Repeat
the procedure for the bearing cone on the opposite side of gear (11).
12. Position gear (20) on gear (11). Install bolts (19). Tighten bolts (19) to a torque of
55 ± 10 N·m (41 ± 7 lb ft). Attach Tooling (A) and a suitable lifting device onto the transfer
gear case. The weight of the transfer gear case is approximately 340 kg (750 lb). Turn over
the transfer gear case. Remove Tooling (A).
13. Lower the temperature of bearing cup (12). Use Tooling (G) to install bearing cup (12) to
the transfer gear case. Check that bearing cup (12) is seated in the bore of the transfer gear
case.
5/9(W)
w
2021/5/15

14. Position gear (11) in the transfer gear case. Install bearing cage (9) and shims (10). Install
bolts (28) that hold bearing cage (9) in position. Tighten bolts (28) to a torque of
55 ± 10 N·m (41 ± 7 lb ft).
15. Position Tooling (H) in the transfer gear case, as shown. Make sure that the dial indicator is
in contact with gear (11). Use a pry bar to move gear (11) up and down. Adjust shims (10)
to obtain an end play of 0.15 ± 0.05 mm (0.006 ± 0.002 inch). Tighten bolts (28) to a torque
of 55 ± 10 N·m (41 ± 7 lb ft).
6/9(W)
w
2021/5/15

16. Use Tooling (G) to install bearing cups (7) and (8) to the transfer gear case. Check that
bearing cups (7) and (8) is seated in the bore of the transfer gear case.
17. Position gear (6) in the transfer gear case with the internal snap ring groove facing up.
Install bearing cage (4) and shims (5). Install the bolts (29) that hold bearing cage (4) in
position. Tighten bolts (29) to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
18. Attach Tooling (A) and a suitable lifting device to the transfer gear case. Place the transfer
gear case on wood blocks, as shown. Position Tooling (H) on the transfer gear case, as
shown. Make sure that the dial indicator is in contact with gear (6). Use a pry bar to move
gear (6) up and down. Adjust shims (5) to obtain an end play of 0.15 ± 0.05 mm
(0.006 ± 0.002 inch). Tighten bolts (29) to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
7/9(W)
w
2021/5/15

19. Position gear (3) in the transfer gear case. Install bearing cage (1) and shims (2). Install the
bolts (30) that hold bearing cage (1) in position. Tighten bolts (30) to a torque of
55 ± 10 N·m (41 ± 7 lb ft).
20. Position Tooling (H) on the transfer gear case, as shown. Make sure that the dial indicator is
in contact with gear (3). Use a pry bar to move gear (3) up and down. Adjust shims (2) to
obtain an end play of 0.15 ± 0.05 mm (0.006 ± 0.002 inch). Tighten bolts (30) to a torque of
55 ± 10 N·m (41 ± 7 lb ft).
End By:
a. Install the transmission oil pump. Refer to Disassembly and Assembly, "Transmission Oil
Pump - Install".
b. Install the transmission scavenge pump. Refer to Disassembly and Assembly, "Transmission
Scavenge Pump - Install".
c. Install the transmission oil filter base. Refer to Disassembly and Assembly, "Transmission
Oil Filter Base - Remove and Install".
d. Install the transfer gear case. Refer to Disassembly and Assembly, "Transfer Gears -
Install".
8/9(W)
w
2021/5/15

Shutdown SIS
Previous Screen
627G Wheel Tractor
Power Train
i02038459
Transfer Gears - Install - In Chassis
SMCS - 3159-012
Installation Procedure
Table 1
Required Tools
C 1/2 - 13 NC by 6 inch Threaded Rod 2
1. Clean all parts and inspect all parts. If any parts are worn or damaged, use new parts for
replacement.
2. Lubricate O-ring seals with the lubricant that is being sealed.
3. Install the O-ring seal to the transfer gear case.
4. Install Tooling (C) in the transmission case.
1/3(W)
w
2021/5/15

5. Use Tooling (A) and a suitable lifting device to position the transfer gear case to the
transmission.
6. Remove Tooling (C). Install the nuts (not shown) and bolts (3) that secure the transfer gear
case to the transmission case. Tighten the nuts (not shown) and bolts (3) to a torque of 105 ±
20 N·m (77 ± 15 lb ft).
7. Install the piston pump for the cushion-hitch. Refer to Machine Systems Disassembly and
Assembly, "Piston Pump (Cushion-Hitch) - Install".
8. Install the vane pump for the hydraulic system and the steering system. Refer to Machine
Systems Disassembly and Assembly, "Vane Pump (Hydraulic and Steering) - Install".
9. Install the drive shaft. Refer to Disassembly and Assembly, "Drive Shaft - Remove and
Install".
10. Install the speed sensor. Refer to Disassembly and Assembly, "Speed Sensor (Transmission)
- Install".
2/3(W)
w
2021/5/15

11. Install drain plugs (1) and (2). Fill the transmission case with oil. Refer to Operation and
Maintenance Manual for the appropriate oil and the procedure to fill the transmission case.
12. Install the power train guard. Refer to Disassembly and Assembly, "Power Train Guard
(Transmission) - Remove and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 15 13:03:40 UTC+0800 2021
3/3(W)
w
2021/5/15

Shutdown SIS
Previous Screen
627G Wheel Tractor
Power Train
i01625485
Transmission Planetary - Disassemble
SMCS - 3030-015
Disassembly Procedure
Start By:
A. Separate the transfer gears from the transmission. Refer to Disassembly and Assembly,
"Transmission and Transfer Gears - Separate".
B. Remove the transmission hydraulic control valve. Refer to Disassembly and Assembly,
"Transmission Hydraulic Control Valve - Remove".
Table 1
Required Tools
A 1P-2420 Transmission Repair Stand 1
B FT-0833 Clamp 2
C 2P-8312 Pliers 1
D FT-1335 Transmission Fixture 1
E 1P-0520 Driver Group 1
NOTICE
Contaminants may cause rapid wear and shortened component life.
1/34(W)
w
2021/5/15

1. Install two 1/2 inch - 13 NC eyebolts, lifting chains, and a hoist onto transmission assembly
(1). Position transmission assembly (1) onto tooling (A). The transmission assembly weighs
approximately 703 kg (1550 lb).
2. Remove eighteen bolts (2) and the washers that secure the transmission assembly to
transmission housing (3). Remove the transmission assembly from transmission housing (3).
Position the transmission assembly onto two wood blocks. Remove the tooling.
2/34(W)
w
2021/5/15

3. Remove sixteen bolts (4) and the washers from clutch housing (5) .
4. Use tooling (B) in order to hold the piston into clutch housing (5). Install two 1/2 inch - 13
NC eyebolts, lifting chains, and a hoist onto clutch housing (5). Remove clutch housing (5)
from the transmission assembly. The clutch housing weighs approximately 27 kg (60 lb).
Remove the tooling.
3/34(W)
w
2021/5/15

5. Remove piston (6) from clutch housing (5). Remove a seal ring (7) from piston (6) and from
clutch housing (5) .
Note: Friction discs and clutch plates that are removed from each clutch housing should be
kept with the correct clutch housing. Mixing the clutch plates and friction discs may cause
improper operation of the transmission or damage to the transmission.
6. Remove ten springs (8), five dowels (9), four friction discs (10) and three clutch plates (11)
from clutch housing (12) .
7. Remove ring gear (13) from clutch housing (12) .
4/34(W)
w
2021/5/15

NC eyebolts, lifting chains, and a hoist onto clutch housing (12). Remove clutch housing
(12) from housing assembly (14). The clutch housing weighs approximately 27 kg (60 lb).
Remove the tooling.
9. Remove piston (15) from clutch housing (12). Remove a seal ring (16) from piston (15) and
5/34(W)
w
2021/5/15

10. Remove ten springs (17), five dowels (18), four friction discs (19) and three clutch plates
(20) from housing assembly (14) .
11. Remove retaining ring (21) from shaft (22) .
12. Install two 3/8 inch - 16 NC eyebolts, lifting chains, and a hoist onto carrier assembly (23).
Remove carrier assembly (23) from housing assembly (14). Remove the tooling. The carrier
assembly weighs approximately 34 kg (75 lb).
6/34(W)
w
2021/5/15

13. Remove eight bolts (24) and oil slinger (25) from carrier assembly (23). Remove bearing
(26) from carrier assembly (23) .
14. Use a hammer and a punch in order to push pin (27) into shaft (28) .
7/34(W)
w
2021/5/15

15. Remove shaft (28), four thrust discs (29) and two planetary gears (30) from carrier assembly
(23). Remove pin (27) from shaft (28) .
16. Remove two bearings (31) from planetary gear (30) .
17. Repeat Steps 14, 15, and 16 in order to remove the remaining three shaft assemblies.
8/34(W)
w
2021/5/15

19. Remove shaft (33), two thrust discs (34) and gear (35) from carrier assembly (23). Remove
tube (36) from shaft (33). Remove pin (32) from shaft (33) .
20. Remove two bearings (37) and spacer (38) from gear (35).
21. Repeat Steps 18, 19, and 20 in order to remove the remaining three shaft assemblies from
the carrier assembly.
9/34(W)
w
2021/5/15

22. Remove six bolts (39) and three plates (40) from clutch housing (41). Remove ring gear
(42) from clutch housing (41) .
23. Remove two bolts (43) that secure clutch housing (41) to housing assembly (14) .
NC eyebolts, lifting chains, and a hoist onto clutch housing (41). Remove clutch housing
(41) from housing assembly (14). The clutch housing weighs approximately 27 kg (60 lb).
Remove the tooling.
10/34(W)
w
2021/5/15

25. Remove piston (44) from clutch housing (41). Remove a seal ring (45) from piston (44) and
26. Remove ten springs (46), two friction discs (47), and clutch plate (48) from housing
assembly (14) .
11/34(W)
w
2021/5/15

27. Remove ring gear (49) from housing assembly (14). Remove plate assembly (50) from
housing assembly (14) .
28. Remove retaining ring (51) from shaft (22). Remove sun gear (52) and sun gear (53) from
shaft (22) .
29. Remove eight bolts (54) and the washers in order to remove carrier assembly (55) from
housing assembly (14).
12/34(W)
w
2021/5/15

30. Install two 3/8 inch - 16 NC eyebolts, lifting chains, and a hoist onto carrier assembly (55).
Remove carrier assembly (55) from housing assembly (14). The carrier assembly weighs
approximately 14 kg (30 lb). Remove the tooling.
13/34(W)
w
2021/5/15

32. Remove shaft (57), two thrust discs (58) and gear (59) from carrier assembly (55). Remove
pin (56) from shaft (57) .
33. Remove bearing (60) from gear (59) .
34. Follow Steps 31, 32, and 33 in order to remove the remaining two shaft assemblies from the
carrier assembly.
35. Remove five springs (61), ten spring assemblies (62), two friction discs (63) and clutch
plate (64) from housing assembly (65). Remove five reaction dowels (66) from housing
assembly (65) .
14/34(W)
w
2021/5/15

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

36. Remove ten spring assemblies (67) and five lock plates (68) from housing assembly (65) .
37. Remove coupling (69) and gear (70) as one unit from housing assembly (65) .
38. Remove two seal rings (71) from gear (70) .
15/34(W)
w
2021/5/15

39. Remove piston (72) from housing assembly (65). Remove seal ring (73) from piston (72) .
40. Use tooling (C) in order to remove retaining ring (74) from shaft (22) .
16/34(W)
w
2021/5/15

Caterpillar Cat 627G Wheel Tractor (Prefix AXF) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 627G Wheel Tractor (Prefix AXF) Service Repair Manual Instant Download.pdf

Similar to Caterpillar Cat 627G Wheel Tractor (Prefix AXF) Service Repair Manual Instant Download.pdf (11)

More from 9fiisekodkdmd

More from 9fiisekodkdmd (20)

Recently uploaded

Recently uploaded (19)

Caterpillar Cat 627G Wheel Tractor (Prefix AXF) Service Repair Manual Instant Download.pdf