What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
2. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 637G WHEEL SCRAPER DEY
Configuration: 637G Wheel Scraper Coal Bowl DEY00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
637G Wheel Tractor-Scraper
Wheel Scraper Power Train
Media Number -RENR8606-00 Publication Date -01/04/2006 Date Updated -21/04/2006
i04332691
Torque Converter - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-1861 Retaining Ring Pliers 1
C 1P-0520 Driver Gp 1
D 2P-8312
Retaining Ring Pliers
(External)
1
E 8H-0663
Bearing Puller Gp
(Nine Ton Capacity)
1
F
1P-2322
Combination Puller
(Two Jaw or Three Jaw)
1
1P-0546 Puller Jaw 1
1P-0510 Driver Gp 1
Start By:
a. Separate the torque converter from the transmission. Refer to Disassembly and Assembly,
"Torque Converter, Transmission and Transfer Gear - Separate".
1/11(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00833596
1. Remove retaining ring (1). Remove retarder rotor (2).
Illustration 2 g00833624
2. Remove seal ring (4) from carrier (3) on each side of retarder rotor (2).
3. Remove carrier (3).
2/11(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Note: The carrier will be destroyed when the carrier is removed from the retarder.
Illustration 3 g00833629
4. Remove bolts (5). Remove race (6).
Illustration 4 g00833647
5. Attach Tooling (A) and a suitable lifting device to housing assembly (7). The weight of
housing assembly (7) is approximately 73 kg (160 lb).
6. Remove housing assembly (7) from the torque converter.
3/11(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 5 g00833655
7. Position housing assembly (7), as shown.
8. Remove bolts (9). Remove gear (8).
Illustration 6 g00833666
9. Use Tooling (B) to remove retaining ring (10) from each side of gear (8).
Illustration 7 g00833676
10. Remove shaft (11).
4/11(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 8 g00833678
11. Use a suitable press and Tooling (C) to remove the bearing from gear (8).
Illustration 9 g01160856
Illustration 10 g00837275
12. Remove bolts (12). Remove housing assembly (13).
13. Remove piston (14) from housing assembly (13). Remove seals (15).
Illustration 11 g00837277
5/11(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. 14. Remove disc assembly (16).
Illustration 12 g00837274
Illustration 13 g00837280
Illustration 14 g01160859
15. Remove retainer (17) from shaft (22). Remove ring seals (18).
16. Remove gear (19) from shaft (22).
17. Remove bolts (20) and retainer (21). Use Tooling (D) to remove retaining ring (23).
6/11(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 15 g01160895
18. Position the torque converter, as shown. Remove bolts (24).
Illustration 16 g01160896
19. Attach Tooling (A) and a suitable lifting device to impeller assembly (25). The weight of
impeller assembly (25) is approximately 41 kg (90 lb).
20. Remove impeller assembly (25) from housing (26).
Illustration 17 g01160897
21. Remove retaining ring (27) and the bearing.
7/11(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 18 g01160860
22. Use Tooling (F) to separate shaft (22) from carrier assembly (28) and the bearing. Remove
the bearing.
Illustration 19 g00837179
23. Remove bolts (29). Remove stator assembly (31) from impeller (30).
Illustration 20 g01160933
8/11(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 21 g01160931
24. Remove bolts (32) from gear (33).
25. Use Tooling (B) to drive carrier assembly (28) and gear (33) out of impeller (30).
Illustration 22 g00837205
26. Use Tooling (B) to drive carrier (34) out of impeller (30).
Illustration 23 g01054015
27. Use Tooling (B) to drive carrier assembly (28) out of bearing (35).
9/11(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 24 g01054017
28. Remove gear (33) from carrier assembly (28).
Illustration 25 g01054020
29. Remove seal ring (36).
Illustration 26 g01160861
30. Remove rings (37). Use Tooling (D) to remove ring (38) from shaft (22).
10/11(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 27 g01160862
31. Install Tooling (E). Tooling (E) must be seated on the shoulders of turbine (39). Tooling (E)
must not contact the splines on shaft (22).
Note: Tooling (E) must be used in order to support turbine (39) or damage to turbine (39)
will result.
Illustration 28 g01160863
32. Use a suitable press to remove shaft (22) from turbine (39). Remove bearing race (40) and
the spacer from turbine (39).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 26 16:17:10 UTC+0800 2021
11/11(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 637G WHEEL SCRAPER DEY
Configuration: 637G Wheel Scraper Coal Bowl DEY00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
637G Wheel Tractor-Scraper
Wheel Scraper Power Train
Media Number -RENR8606-00 Publication Date -01/04/2006 Date Updated -21/04/2006
i02322407
Torque Converter - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-1861 Retaining Ring Pliers 1
C 1P-0520 Driver Gp 1
D 2P-8312
Retaining Ring Pliers
(External)
1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/10(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 1 g01160861
1. Lower the temperature of shaft (22). Use Tooling (D) to install ring (38). Install shaft (22) in
the turbine until ring (38) rests on the turbine. Install rings (37).
Illustration 2 g01160941
2. Install the spacer. Raise the temperature of bearing race (40). Install bearing race (40) to
turbine (39) and shaft (22).
Illustration 3 g01054020
3. Install seal ring (36).
2/10(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 4 g01054017
4. Install gear (33) to carrier assembly (28).
Illustration 5 g01054015
5. Raise the temperature of bearing (35). Install bearing (35) on carrier assembly (28).
Illustration 6 g00837205
6. Lower the temperature of carrier (34). Install carrier (34) into impeller (30).
Note: Make sure that the bolt holes are aligned.
3/10(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 7 g00837194
7. Position gear (33). Install bolts (32). Tighten bolts (32) to a torque of 50 ± 7 N·m
(37 ± 5 lb ft).
Illustration 8 g00837179
8. Position stator assembly (31) on impeller (30) and on carrier assembly (28). Install bolts
(29). Tighten bolts (29) to a torque of 40 ± 5 N·m (30 ± 4 lb ft).
Illustration 9 g01160943
9. Install carrier assembly (28) on impeller (39).
4/10(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. 10. Raise the temperature of the bearing. Install the bearing on shaft (22).
Illustration 10 g01160897
11. Lower the temperature of the bearing. Install the bearing. Install retaining ring (27).
Illustration 11 g01160896
12. Use Tooling (A) and a suitable lifting device to install impeller assembly (25) to housing
(26). The weight of impeller assembly (25) is approximately 41 kg (90 lb).
Illustration 12 g01160895
5/10(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. 13. Position the torque converter, as shown. Install bolts (24). Tighten bolts (24) to a torque of
30 ± 5 N·m (22 ± 4 lb ft).
Illustration 13 g01160859
Illustration 14 g00837280
Illustration 15 g00837274
14. Use Tooling (D) to install retaining ring (23). Position retainer (21). Install bolts (20).
Tighten bolts (20) to a torque of 50 ± 7 N·m (37 ± 5 lb ft).
15. Install gear (19) on shaft (22).
6/10(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. 20. Install bolts (12). Tighten bolts (12) to a torque of 50 ± 7 N·m (37 ± 5 lb ft).
Illustration 19 g00833678
21. Use a suitable press and Tooling (C) to install the bearing to gear (8).
Illustration 20 g00833676
22. Install shaft (11).
Illustration 21 g00833666
23. Use Tooling (B) to install retaining ring (10) on each side of gear (8).
8/10(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 22 g00833655
24. Position housing assembly (7), as shown.
25. Position gear (8). Install bolts (9).
Illustration 23 g00833647
26. Attach Tooling (A) and a suitable lifting device to housing assembly (7). The weight of
housing assembly (7) is approximately 73 kg (160 lb).
27. Install housing assembly (7) onto the torque converter.
Illustration 24 g00833629
9/10(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. 28. Install race (6). Install bolts (5).
Illustration 25 g00833624
29. Install carrier (3).
30. Install seal ring (4) to carrier (3) on each side of retarder rotor (2).
Illustration 26 g00833596
31. Install retarder rotor (2). Install retaining ring (1).
End By:
a. Connect the torque converter to the transmission. Refer to Disassembly and Assembly,
"Torque Converter, Transmission and Transfer Gear - Connect".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 26 16:18:06 UTC+0800 2021
10/10(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 637G WHEEL SCRAPER DEY
Configuration: 637G Wheel Scraper Coal Bowl DEY00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
637G Wheel Tractor-Scraper
Wheel Scraper Power Train
Media Number -RENR8606-00 Publication Date -01/04/2006 Date Updated -21/04/2006
i02331325
Transfer Gears - Disassemble
SMCS - 3159-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
B
1P-0820 Hydraulic Puller 1
3H-0465 Push-Puller Plate 4
8B-7549 Puller Leg 2
8B-7551 Bearing Puller Gp 1
C 138-7573 Link Bracket 2
D
5F-7343
Bearing Puller Gp
(Twenty Ton Capacity)
1
1P-0520 Driver Gp 1
E
8B-7551 Bearing Puller Gp 1
1P-0520 Driver Gp 1
Start By:
A. Remove the transmission. Refer to Disassembly and Assembly, "Torque Converter,
Transmission, and Transfer Gear - Separate".
1/9(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00834630
1. Remove cover (1) .
2/9(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. 5. Position cage assembly (3). Remove bolts (8). Remove plate (9). Remove O-ring seal (10) .
Illustration 5 g00834589
Illustration 6 g00834834
6. Use Tooling (A) and a suitable press in order to remove bearings (11) from cage assembly
(3) .
4/9(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Illustration 7 g00834594
Note: If the shaft is not supported, the shaft will fall when bolt (13) is removed.
7. Position transfer case (12). Support shaft (14). Remove bolt (13). Remove the retainer.
Remove shaft (14) .
8. Remove gear (15) from transfer case (12) .
Illustration 8 g00834598
9. Use Tooling (B) in order to remove bearing (16) from shaft (14) .
Illustration 9 g00834608
10. Remove bolts (17) .
5/9(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. Illustration 10 g00834615
11. Attach Tooling (C) and a suitable lifting device to cage (18). Remove cage (18) and the
pinion as a unit. The weight of cage (18) and the pinion is approximately 34 kg (76 lb).
Illustration 11 g00834620
12. Remove bolts (19). Remove plate (20). Remove bearing cone (21) .
Illustration 12 g00834621
6/9(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
29. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
30. 13. Use Tooling (D) and a suitable press in order to remove cage (18) from pinion (22) .
Illustration 13 g00834623
14. If necessary, use Tooling (E) in order to remove bearing cone (23) from pinion (22). If
necessary, use Tooling (E) in order to remove bearing cone (24) from pinion (22) .
Illustration 14 g00834625
15. Remove retaining ring (25) in order to remove bearing cup (26) from cage (18) .
7/9(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
31. Illustration 15 g00834626
16. Use Tooling (A) and a suitable press in order to remove the bearing cup from cage (18) .
Illustration 16 g00834628
17. Remove plug (27). Remove the dowel that holds the race in position.
Illustration 17 g00834629
18. Remove bearing race (28). Remove bearing race (29) .
8/9(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...