2. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 657G WHEEL SCRAPER W1E
Configuration: 657G Wheel Scraper W1E00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
657G Wheel Scraper Power Train
Media Number -RENR9713-00 Publication Date -01/09/2006 Date Updated -19/09/2006
i02596939
Drive Shaft - Remove and Install
SMCS - 3253-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-7405 Eyebolt 1
B 5J-0490
Forcing Bolt
1/2 x 13 NC
2
C 2P-8312 Retaining Ring Pliers 1
Start By:
A. Remove the push-pull hook. Refer to Disassembly and Assembly, "Push-Pull Hook -
Remove and Install".
1. Move the ejector to the eject position.
1/16(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
4. Illustration 4 g01273346
5. Remove cover (4) .
Illustration 5 g01273347
6. Remove retaining ring (5) from drive shaft (6) .
3/16(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5. Illustration 6 g01273348
7. Install Tooling (A) in drive shaft (6). Use Tooling (A) in order to partially remove drive
shaft (6) .
Illustration 7 g01273349
8. Attach a suitable lifting device to drive shaft (6). Remove drive shaft (6). The weight of
drive shaft (6) is approximately 34 kg (75 lb).
Illustration 8 g01273350
9. Remove bolts (7). Use two people in order to remove tube assembly (8). The weight of tube
assembly (8) is approximately 24 kg (52 lb).
4/16(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
6. Illustration 9 g01273351
10. Remove yoke assembly (9) .
Illustration 10 g01273355
11. Use Tooling (C) to remove retaining ring (10) from yoke assembly (9) .
12. Remove bearing (11), spacer (12), bearing (13), and spacer (14) from yoke assembly (9) .
5/16(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
7. Illustration 11 g01273352
13. Remove nuts (15) .
Illustration 12 g01273354
14. Use Tooling (B) to remove bearing cage (16) .
15. If necessary, remove studs (17) .
Illustration 13 g01273356
6/16(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
8. 16. Remove seal (18) from bearing cage (16) .
Illustration 14 g01273370
17. Remove plugs (22) and the bearing dowels.
18. Remove bearing (19), spacer (20), and bearing (21) from bearing cage (16) .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1P-7405 Eyebolt 1
C 2P-8312 Retaining Ring Pliers 1
D 1P-0520 Driver Gp 1
E 297-8327 (1)
Alignment Adapter 1
F 1A-8063
Bolt
3/4 x 10 NC
1
G 297-8329 (1)
Alignment Shaft 1
H 297-8330 (1)
Alignment Adapter 1
( 1 )
Also part of 297-8326 Alignment Group
7/16(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
9. Illustration 15 g01273370
1. Install bearing (19), spacer (20), and bearing (21) into bearing cage (16) .
2. Install the bearing dowels and plugs (22) .
Illustration 16 g01273356
Note: Lubricate seal (18) with the lubricant that is being sealed.
3. Use Tooling (D) to install seal (18) into bearing cage (16) .
8/16(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
10. Illustration 17 g01274202
4. If necessary, install studs (17). Tighten studs (17) to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
Install bearing cage (16) and nuts (15) .
Note: Steps 5 through 12 must be preformed in order to ensure proper alignment of the
engine assembly to the axle.
Illustration 18 g01300092
5. Remove bolt (23), washer (24), and seal (25) (not shown).
9/16(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
11. Illustration 19 g01300095
Note: Do not tighten Tooling (F) .
6. Install Tooling (E). Install Tooling (F). Hand tighten Tooling (F) only.
Illustration 20 g01300096
7. Install Tooling (G) into Tooling (E) .
Illustration 21 g01300097
8. Install Tooling (H). Use Tooling (G) to check the alignment of the axle housing and the
engine.
10/16(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
12. Illustration 22 g01300099
9. When Tooling (G) can slide into both Tooling (E) and Tooling (H), the axle housing and the
engine are in alignment. If necessary, adjust the position of the engine in order to achieve
alignment.
Illustration 23 g01300097
10. Remove Tooling (H) and Tooling (G) .
Illustration 24 g01300095
11/16(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
13. 11. Remove Tooling (F) and Tooling (E) .
Illustration 25 g01300092
12. Install seal (25) (not shown), washer (24), and bolt (23) .
Illustration 26 g01273355
Note: Assemble the end of bearing (13) that has a radius toward the shoulder of yoke
assembly (9) .
13. Install bearing (11), spacer (12), bearing (13), and spacer (14) to yoke assembly (9) .
14. Use Tooling (C) to install retaining ring (10) to yoke assembly (9) .
12/16(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
14. Illustration 27 g01273351
15. Install yoke assembly (9) .
Illustration 28 g01273350
Note: Prior to the installation of tube assembly (8), place a dial indicator on the face of the
yoke assembly. Indicate the outside diameter of yoke of the transfer gear. This reading must
not exceed 5 mm (0.2 inch) total indicator reading.
16. Use two people in order to position tube assembly (8). The weight of tube assembly (8) is
approximately 24 kg (52 lb). Install bolts (7). Tighten bolts (7) to a torque of 435 ± 20 N·m
(321 ± 15 lb ft).
13/16(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
15. Illustration 29 g01273349
17. Attach a suitable lifting device to drive shaft (6). Install drive shaft (6). The weight of drive
shaft (6) is approximately 34 kg (75 lb).
Illustration 30 g01273348
18. Remove Tooling (A) from drive shaft (6) .
Illustration 31 g01273347
14/16(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
16. 19. Use Tooling (C) to install retaining ring (5) to drive shaft (6) .
Illustration 32 g01273346
20. Install cover (4) .
Illustration 33 g01273345
21. Install guard assemblies (3) .
15/16(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
17. Illustration 34 g01273344
22. Connect harness assembly (2). Position harness assembly (2) and install the clips.
Illustration 35 g01273343
23. Install guard assemblies (1) .
End By: Install the push-pull hook. Refer to Disassembly and Assembly, "Push-Pull Hook -
Remove and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Feb 4 01:00:43 UTC+0800 2021
16/16(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
18. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 657G WHEEL SCRAPER W1E
Configuration: 657G Wheel Scraper W1E00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
657G Wheel Scraper Power Train
Media Number -RENR9713-00 Publication Date -01/09/2006 Date Updated -19/09/2006
i02594202
Scavenge Pump and Mounting (Flywheel) - Remove
SMCS - 1167-011
Removal Procedure
Illustration 1 g01298546
1. Loosen clamp (6). Remove bolts (1) and reposition manifold (2) .
2. Disconnect hose assembly (3) .
3. Remove bolts (4) and flywheel scavenge pump (5) .
Thu Feb 4 01:01:39 UTC+0800 2021
1/2(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
19. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 657G WHEEL SCRAPER W1E
Configuration: 657G Wheel Scraper W1E00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
657G Wheel Scraper Power Train
Media Number -RENR9713-00 Publication Date -01/09/2006 Date Updated -19/09/2006
i02566083
Scavenge Pump and Mounting (Flywheel) - Disassemble
SMCS - 1167-015
Disassembly Procedure
Start By:
A. Remove the flywheel scavenge pump. Refer to Disassembly and Assembly, "Scavenge
Pump and Mounting (Flywheel) - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
20. Illustration 1 g01285135
1. Remove O-ring seal (2). Remove bolts (1) and body assembly (3) .
Illustration 2 g01285138
2. Remove O-ring seal (4). Remove bearing (5) .
Illustration 3 g01285145
3. Remove shaft assembly (6) and gear assembly (7) .
2/3(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
21. Illustration 4 g01285146
4. Remove dowel (8). Remove bearing (9). Remove shaft (10) .
Illustration 5 g01285147
5. Remove bearing (11) from gear assembly (7) .
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Feb 4 01:02:35 UTC+0800 2021
3/3(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
22. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 657G WHEEL SCRAPER W1E
Configuration: 657G Wheel Scraper W1E00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
657G Wheel Scraper Power Train
Media Number -RENR9713-00 Publication Date -01/09/2006 Date Updated -19/09/2006
i02566087
Scavenge Pump and Mounting (Flywheel) - Assemble
SMCS - 1167-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
Note: Lubricate the pump with oil before running.
Illustration 1 g01285147
1. Install bearing (11) into gear assembly (7) .
1/3(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
23. Illustration 2 g01285242
2. Install bearing (9) so that the joint is 30 ± 15 degrees from the centerline, as shown.
3. Use Tooling (A) to install bearing (9) by an additional 1.57 mm (0.062 inch).
4. Install dowel (8). Install shaft (10) .
Illustration 3 g01285145
5. Install shaft assembly (6) and gear assembly (7) .
2/3(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
24. Illustration 4 g01285245
6. Install bearing (5) so that the joint is 30 ± 15 degrees from the centerline, as shown.
7. Use Tooling (A) to install bearing (5) by an additional 1.04 mm (0.041 inch).
8. Install O-ring seal (4) .
Illustration 5 g01285135
9. Position body assembly (3) and install bolts (1). Install O-ring seal (2) .
End By: Install the flywheel scavenge pump. Refer to Disassembly and Assembly, "Scavenge
Pump and Mounting (Flywheel) - Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Feb 4 01:03:31 UTC+0800 2021
3/3(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
25. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 657G WHEEL SCRAPER W1E
Configuration: 657G Wheel Scraper W1E00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
657G Wheel Scraper Power Train
Media Number -RENR9713-00 Publication Date -01/09/2006 Date Updated -19/09/2006
i02594208
Scavenge Pump and Mounting (Flywheel) - Install
SMCS - 1167-012
Installation Procedure
Illustration 1 g01298546
1. Position flywheel scavenge pump (5) and install bolts (4) .
2. Connect hose assembly (3) .
3. Position manifold (2) and install bolts (1). Tighten clamp (6) .
Thu Feb 4 01:04:26 UTC+0800 2021
1/2(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
26. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 657G WHEEL SCRAPER W1E
Configuration: 657G Wheel Scraper W1E00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
657G Wheel Scraper Power Train
Media Number -RENR9713-00 Publication Date -01/09/2006 Date Updated -19/09/2006
i02544838
Retarder Hydraulic Control Valve - Remove
SMCS - 3123-011-HR
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
27. Illustration 1 g01273585
1. Disconnect hose assemblies (2), (3), and (4) from retarder hydraulic control valve (1) .
Illustration 2 g01273588
2. Disconnect harness assembly (6) and hose assemblies (5) and (7) from retarder hydraulic
control valve (1) .
3. Remove bolts (8) and retarder hydraulic control valve (1) .
2/3(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
28. Illustration 3 g01273579
4. Remove O-ring seals (9) .
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Feb 4 01:05:23 UTC+0800 2021
3/3(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
29. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
30. Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 657G WHEEL SCRAPER W1E
Configuration: 657G Wheel Scraper W1E00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
657G Wheel Scraper Power Train
Media Number -RENR9713-00 Publication Date -01/09/2006 Date Updated -19/09/2006
i02544836
Retarder Hydraulic Control Valve - Disassemble
SMCS - 3123-015-HR
Disassembly Procedure
Start By:
A. Remove the retarder hydraulic control valve. Refer to Disassembly and Assembly,
"Retarder Hydraulic Control Valve - Remove".
Illustration 1 g01273534
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
1/4(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
31. Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove covers (1) and (2) .
Illustration 2 g01273544
Illustration 3 g01273536
2. Remove spool assembly (3) .
2/4(W)
w
2021/2/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...