This document provides instructions for removing and installing the unit injector sleeve and unit injector hydraulic pump on a Caterpillar C9 engine. The removal process involves disconnecting fuel lines and electrical connections, removing mounting bolts, and extracting the components. Installation is the reverse process, and includes cleaning parts, applying new seals, and reconnecting all connections once the components are secured with bolts. Proper containment of fluids and cleaning of parts to prevent contamination is emphasized.
Caterpillar cat 336 d2 l excavator (prefix lam) service repair manual (lam000...fjekkdmmem
This document provides instructions for removing and installing unit injector sleeves and the unit injector hydraulic pump on a Caterpillar C9 engine.
The removal procedure involves draining coolant, cutting threads in the injector sleeve using special tools, and removing the sleeve. For the pump, it describes disconnecting fuel lines and electrical connections before removing mounting bolts.
The installation procedure involves cleaning parts, applying new seals, and securing the sleeve and pump in place using the appropriate tools while applying retaining compound or grease as specified.
Caterpillar cat 336 d2 l excavator (prefix lam) service repair manual (lam000...fjjskekdm
This document provides instructions for removing and installing a unit injector sleeve and unit injector hydraulic pump on a Caterpillar C9 engine. The removal process involves draining coolant, using tools to cut threads and remove the sleeve, and cleaning parts. The installation process requires cleaning bores, applying sealant, and using a hammer and installer to position the sleeve. Proper containment of fluids is emphasized.
Caterpillar cat 336 d2 l excavator (prefix elr) service repair manual (elr000...fjjskmdmem
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tube assemblies, hoses, and electrical harnesses from the pump. Bolts are then removed to allow the pump to be lifted off. Installation involves reversing these steps and ensuring a new O-ring seal is installed. Proper cleanliness and containment of fluids is emphasized throughout.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tube assemblies, hoses, and electrical harnesses from the pump. Bolts are then removed to allow the pump to be lifted off. Installation involves reversing these steps and ensuring a new O-ring seal is installed. Proper cleanliness and containment of fluids is emphasized throughout.
Caterpillar cat 336 d2 l excavator (prefix elr) service repair manual (elr000...fhjsjkdmemm
This document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the process is reversed - mounting bolts are installed and all connections reattached. Proper cleaning and use of new O-rings is emphasized to prevent contamination.
This document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the process is reversed - mounting bolts are installed and all connections reattached. Proper cleaning and use of new O-rings is emphasized to prevent contamination.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tube assemblies, hoses, and electrical harnesses from the pump. Bolts are then removed to allow the pump to be lifted off. Installation involves reversing these steps, ensuring all connections are clean and sealing properly. Tools and safety precautions are also listed to contain fluids and prevent contamination.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix ELR) Service Repair Manua...fijsekkdmdm2w
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tube assemblies, hoses, and electrical harnesses from the pump. Bolts are then removed to allow the pump to be lifted off. Installation involves reversing these steps, ensuring all connections are clean and sealing properly. Tools and safety precautions are also listed.
Caterpillar cat 336 d2 l excavator (prefix lam) service repair manual (lam000...fjekkdmmem
This document provides instructions for removing and installing unit injector sleeves and the unit injector hydraulic pump on a Caterpillar C9 engine.
The removal procedure involves draining coolant, cutting threads in the injector sleeve using special tools, and removing the sleeve. For the pump, it describes disconnecting fuel lines and electrical connections before removing mounting bolts.
The installation procedure involves cleaning parts, applying new seals, and securing the sleeve and pump in place using the appropriate tools while applying retaining compound or grease as specified.
Caterpillar cat 336 d2 l excavator (prefix lam) service repair manual (lam000...fjjskekdm
This document provides instructions for removing and installing a unit injector sleeve and unit injector hydraulic pump on a Caterpillar C9 engine. The removal process involves draining coolant, using tools to cut threads and remove the sleeve, and cleaning parts. The installation process requires cleaning bores, applying sealant, and using a hammer and installer to position the sleeve. Proper containment of fluids is emphasized.
Caterpillar cat 336 d2 l excavator (prefix elr) service repair manual (elr000...fjjskmdmem
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tube assemblies, hoses, and electrical harnesses from the pump. Bolts are then removed to allow the pump to be lifted off. Installation involves reversing these steps and ensuring a new O-ring seal is installed. Proper cleanliness and containment of fluids is emphasized throughout.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tube assemblies, hoses, and electrical harnesses from the pump. Bolts are then removed to allow the pump to be lifted off. Installation involves reversing these steps and ensuring a new O-ring seal is installed. Proper cleanliness and containment of fluids is emphasized throughout.
Caterpillar cat 336 d2 l excavator (prefix elr) service repair manual (elr000...fhjsjkdmemm
This document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the process is reversed - mounting bolts are installed and all connections reattached. Proper cleaning and use of new O-rings is emphasized to prevent contamination.
This document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the process is reversed - mounting bolts are installed and all connections reattached. Proper cleaning and use of new O-rings is emphasized to prevent contamination.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tube assemblies, hoses, and electrical harnesses from the pump. Bolts are then removed to allow the pump to be lifted off. Installation involves reversing these steps, ensuring all connections are clean and sealing properly. Tools and safety precautions are also listed to contain fluids and prevent contamination.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix ELR) Service Repair Manua...fijsekkdmdm2w
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tube assemblies, hoses, and electrical harnesses from the pump. Bolts are then removed to allow the pump to be lifted off. Installation involves reversing these steps, ensuring all connections are clean and sealing properly. Tools and safety precautions are also listed.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix ELR) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix ELR) Service Repair Manua...fujkskemdmdm4r
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Caterpillar cat 336 d2 l excavator (prefix elr) service repair manual (elr000...ikdkdmddm
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...f8uesjdkdmdm
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...fujjekdmdmd
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the pump. The installation procedure specifies cleaning parts and applying a new O-ring seal before reversing the removal steps and reconnecting all lines and bolts. Proper containment of fluids is emphasized throughout.
This document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the process is reversed - mounting bolts are installed and all connections reattached. Proper cleaning and use of new seals is emphasized to prevent contamination.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...8ufjsekddm8u
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...f8uejkkdmdm8u
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix ELR) Service Repair Manua...ze3xiandiao
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tube assemblies, hoses, and electrical harnesses from the pump. Bolts are then removed to allow the pump to be lifted off. Installation involves reversing these steps, ensuring all connections are clean and sealing properly. Tools and safety precautions are also listed to ensure the work is done correctly.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...f7usuejkdkddm3
This document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the process is reversed - mounting bolts are installed and all connections reattached. Proper cleaning and use of new O-rings is emphasized to prevent contamination.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...ufjksemd8ujd
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tube assemblies, hoses, and electrical harnesses from the pump. Bolts are then removed to allow the pump to be lifted off. Installation involves reversing these steps, ensuring all connections are clean and sealing properly. Tools and safety precautions are listed to contain fluids and prevent contamination.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...fujskmd9dokk
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tube assemblies, hoses, and electrical harnesses from the pump. Bolts are then removed to allow the pump to be lifted off. Installation involves reversing these steps, ensuring all connections are clean and sealing properly. Tools and safety precautions are also listed to ensure the work is done correctly.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tube assemblies, hoses, and electrical harnesses from the pump. Bolts are then removed to allow the pump to be lifted off. Installation involves reversing these steps, ensuring all connections are clean and sealing properly. Tools and safety precautions are also listed to ensure the work is done correctly.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...km7seydwuhdw
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
More Related Content
Similar to Caterpillar Cat 336D2 L Excavator (Prefix LAM) Service Repair Manual (LAM00001 and up).pdf
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix ELR) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix ELR) Service Repair Manua...fujkskemdmdm4r
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Caterpillar cat 336 d2 l excavator (prefix elr) service repair manual (elr000...ikdkdmddm
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...f8uesjdkdmdm
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...fujjekdmdmd
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the pump. The installation procedure specifies cleaning parts and applying a new O-ring seal before reversing the removal steps and reconnecting all lines and bolts. Proper containment of fluids is emphasized throughout.
This document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the process is reversed - mounting bolts are installed and all connections reattached. Proper cleaning and use of new seals is emphasized to prevent contamination.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...8ufjsekddm8u
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...f8uejkkdmdm8u
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix ELR) Service Repair Manua...ze3xiandiao
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tube assemblies, hoses, and electrical harnesses from the pump. Bolts are then removed to allow the pump to be lifted off. Installation involves reversing these steps, ensuring all connections are clean and sealing properly. Tools and safety precautions are also listed to ensure the work is done correctly.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...f7usuejkdkddm3
This document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the process is reversed - mounting bolts are installed and all connections reattached. Proper cleaning and use of new O-rings is emphasized to prevent contamination.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...ufjksemd8ujd
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tube assemblies, hoses, and electrical harnesses from the pump. Bolts are then removed to allow the pump to be lifted off. Installation involves reversing these steps, ensuring all connections are clean and sealing properly. Tools and safety precautions are listed to contain fluids and prevent contamination.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...fujskmd9dokk
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tube assemblies, hoses, and electrical harnesses from the pump. Bolts are then removed to allow the pump to be lifted off. Installation involves reversing these steps, ensuring all connections are clean and sealing properly. Tools and safety precautions are also listed to ensure the work is done correctly.
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tube assemblies, hoses, and electrical harnesses from the pump. Bolts are then removed to allow the pump to be lifted off. Installation involves reversing these steps, ensuring all connections are clean and sealing properly. Tools and safety precautions are also listed to ensure the work is done correctly.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...km7seydwuhdw
The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Similar to Caterpillar Cat 336D2 L Excavator (Prefix LAM) Service Repair Manual (LAM00001 and up).pdf (20)
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
This document provides instructions for removing and installing a flywheel housing on a 416C Backhoe Loader with a 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and replacing seals is emphasized. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and securing it with mounting bolts. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new one. The procedures are separated into sections for engines with a 14-bolt housing assembly versus a 10-bolt housing assembly. Precise instructions are given for lubricating parts, inserting the seal, aligning components, and tightening bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening bolts to specifications.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...f7usuejkdkddm3
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It describes using a puller tool to remove the pulley and pressing the pulley onto the crankshaft during installation. Tightening specifications are included for attaching the pulley.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts, lifting the flywheel off, and potentially removing a ring gear. For the crankshaft rear seal, it differentiates between engines with 14-bolt and 10-bolt housings and explains cleaning, pressing or placing the seal, and torquing bolts.
This document provides instructions for removing the crankshaft front seal from a Caterpillar 3054 engine. The steps are:
1. Use a drill bit to drill out the lock tabs of the seal.
2. Pry the seal out of the housing with a seal removal tool.
3. Inspect the seal bore and remove any debris before installing the new seal.
Caterpillar Cat 345D L Excavator (Prefix RGG) Service Repair Manual (RGG00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, installing components like seals, spacers, washers, and plugs in reverse order of disassembly. Tools required are listed in tables. Cautions are provided about cleanliness, contamination, misassembly, and applying lubricant to parts.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the carrier assembly, ring gear, and bearings. Cleanliness is emphasized during assembly, with seals, O-rings and other parts replaced as needed. The instructions ensure the swing drive is properly disassembled and reassembled.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f7usuejkdkddm3
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
The document provides assembly instructions for a 345C excavator final drive system. It involves assembling three carrier assemblies that contain planetary gears, installing them into a ring gear housing along with other components like bearing cones and seals. The procedure has 26 steps and requires various tools. It ensures proper bearing preload is achieved and components are cleaned, lubricated and torqued correctly during reassembly.
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR LAM
Configuration: 336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i06737900
Unit Injector Sleeve - Remove
SMCS - 1713-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-3042 Plug Tap 1
B 221-0052 Guide Sleeve 1
C
9U-6858 Bridge Plate 1
1B-2886 Bolts 2
221-9778 Puller Stud 1
4K-0367 Full Nut 1
5P-8247 Hard Washer 1
9U-6877 Thrust Bearing 1
D 221-9803 Rubber Stopper 1
Start By:
a. Remove the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Remove".
NOTICE
Keep all parts clean from contaminants.
1/3
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Refill Capacities and Recommendations".
2. Position Tooling (D) at the bottom of the unit injector sleeve.
3. Coat Tooling (A) with clean grease. Use Tooling (A) and Tooling (B) to cut threads into the
unit injector sleeve.
2/3
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 1 g01137445
4. Install Tooling (C) in unit injector sleeve (1).
5. Remove unit injector sleeve (1). Remove the O-ring seals.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jun 1 23:05:57 UTC+0800 2020
3/3
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR LAM
Configuration: 336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i03742983
Unit Injector Sleeve - Install
SMCS - 1713-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
E 221-9777 Sleeve Installer 1
F 4C-5552 Large Bore Brush 1
G 4C-9507 Retaining Compound 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Thoroughly clean the unit injector sleeves and the bores for the unit injectors with Tooling
(F) .
1/2
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 1 g02021929
2. Apply clean engine oil to O-ring seals (2) . Install O-ring seals (2) on unit injector sleeve
(1) .
3. Position unit injector sleeve (1) on Tooling (E) .
4. Apply a thin coating of Tooling (G) around the outer circumference of unit injector sleeve
(1) at Area (C) .
5. Position unit injector sleeve (1) in the cylinder head. Use a hammer to install unit injector
sleeve (1) in the cylinder head.
Note: Allow Tooling (G) to cure for two hours at 21 °C (70 °F) before filling the engine
with fuel or coolant. Longer curing time is required for lower temperatures.
6. Fill the cooling system with coolant to the correct level. Refer to Operation and
Maintenance Manual, "Refill Capacities and Recommendations".
End By: Install the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jun 1 23:06:53 UTC+0800 2020
2/2
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR LAM
Configuration: 336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i05701078
Unit Injector Hydraulic Pump - Remove
SMCS - 1714-011
Removal Procedure for Non-Dual Tapered Roller Bearing
HEUI Pump
Start By:
A. Remove fuel filter base, if necessary.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/8
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 1 g03601539
Non-Dual Taper Roller Bearing HEUI pump
Illustration 2 g03601540
Dual Taper Roller Bearing HEUI pump
Note: Refer to Illustrations 1 and 2 in order to identify each unit injection hydraulic pump.
2/8
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 3 g03614617
1. Disconnect tube assemblies (3) , (4) , (5) , and (6) .
2. Disconnect hose assembly (7) .
3. Disconnect harness assembly (2) from unit injector hydraulic pump (1) .
3/8
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 4 g03614660
4. Support unit injector hydraulic pump (1) by hand and remove bolts (8) . Remove unit
injector hydraulic pump (1) .
4/8
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 5 g03614696
5. Remove O-ring seal (9) .
Removal Procedure for Dual Tapered Roller Bearing HEUI
Pump
Start By:
A. Remove fuel filter base, if necessary.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
5/8
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 6 g03615086
1. Disconnect harness assembly (1) . Disconnect hose assemblies (4) and tube assembly (3) .
Remove tube assembly (2) and tube assembly (5) .
6/8
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 7 g03615089
2. Support unit injector hydraulic pump (7) and remove bolts (6) .
Illustration 8 g03615416
3. Rotate counterclockwise as shown, then remove unit injector hydraulic pump (7) .
7/8
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 9 g03615091
4. Remove O-ring seal (8) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jun 1 23:07:49 UTC+0800 2020
8/8
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR LAM
Configuration: 336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i05701091
Unit Injector Hydraulic Pump - Install
SMCS - 1714-012
Installation Procedure for Non-Dual Taper Roller Bearing
HEUI Pump
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/9
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 1 g03601539
Non-Dual Taper Roller Bearing HEUI pump
Illustration 2 g03601540
Dual Taper Roller Bearing HEUI pump
Note: Refer to Illustrations 1 and 2 in order to identify each unit injection hydraulic pump.
2/9
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 3 g03614696
1. Install new O-ring seal (9) .
3/9
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 4 g03614660
2. Position unit injector hydraulic pump (1) in the front housing.
3. Support unit injector hydraulic pump (1) and install bolts (8) .
4/9
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 5 g03614617
4. Connect hose assembly (7) .
5. Connect tube assemblies (3) , (4) , (5) , and (6) .
6. Connect harness assembly (2) to unit injector hydraulic pump (1) .
Installation Procedure for Dual Tapered Roller Bearing
HEUI Pump
Table 1
Required Tools
Tool Part Number Part Description Qty
A 129-1967 Multipurpose Grease -
Note: If replacing a non-dual tapered roller bearing HEUI pump with a dual tapered roller bearing
HEUI pump, refer to Special Instruction, REHS7902 for rework and installation procedures.
5/9
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 6 g03601539
Non-Dual Taper Roller Bearing HEUI pump
Illustration 7 g03601540
Dual Taper Roller Bearing HEUI pump
Note: Refer to Illustrations 6 and 7 in order to identify each unit injection hydraulic pump.
Note: If a dowel pin is installed in the mounting flange of the unit injector hydraulic pump
or in the front housing at the unit injector hydraulic pump mounting location, remove the
dowel pin before installing the unit injector hydraulic pump.
6/9
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 8 g03615091
1. Install O-ring seal (8) . Apply Tooling (A) to O-ring seal (8) , the mounting flange of the
unit injector hydraulic pump, and the back of the front housing at the mounting location of
the unit injector hydraulic pump.
Illustration 9 g03615798
2. Position unit injector hydraulic pump (7) as shown, then rotate clockwise to final
installation orientation.
7/9
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 10 g03615089
3. Install bolts (6) hand-tight.
Note: Do not fully tighten bolts (6) until all of the hoses and the tubes are connected to unit
injection hydraulic pump (7) .
Illustration 11 g03615086
4. Install tube assembly (5) hand-tight.
5. Connect hose assemblies (4) . Install tube assembly (3) and tube assembly (2) hand-tight.
6. Tighten bolts (6) to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
8/9
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. 7. Tighten tube assemblies (2) , (3) , (5) and hose assemblies (4) .
8. Connect harness assembly (1) .
End By: Install fuel filter base, if necessary.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jun 1 23:08:45 UTC+0800 2020
9/9
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR LAM
Configuration: 336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i02297056
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1/2
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Illustration 1 g01150421
1. Disconnect hose assembly (1).
2. Remove bolts (4) and tube assembly (5).
3. Attach a suitable lifting device onto turbocharger (2). The weight of turbocharger (2) is
approximately 27 kg (60 lb). Remove nuts (3). Remove turbocharger (2) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jun 1 23:09:40 UTC+0800 2020
2/2
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR LAM
Configuration: 336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i04000968
Turbocharger - Install
SMCS - 1052-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-3931 Anti-Seize Compound -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Apply Tooling (A) to the turbocharger mounting studs on the exhaust manifold.
1/2
336D2 L Excavator LAM00001-UP (MACHINE) POWERED BY C9 Engine(SEBP7...
2020/6/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...